1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
* Samsung Exynos 5440 PCIe interface
This PCIe host controller is based on the Synopsis Designware PCIe IP
and thus inherits all the common properties defined in designware-pcie.txt.
Required properties:
- compatible: "samsung,exynos5440-pcie"
- reg: base addresses and lengths of the pcie controller,
the phy controller, additional register for the phy controller.
(Registers for the phy controller are DEPRECATED.
Use the PHY framework.)
- reg-names : First name should be set to "elbi".
And use the "config" instead of getting the confgiruation address space
from "ranges".
NOTE: When use the "config" property, reg-names must be set.
- interrupts: A list of interrupt outputs for level interrupt,
pulse interrupt, special interrupt.
- phys: From PHY binding. Phandle for the Generic PHY.
Refer to Documentation/devicetree/bindings/phy/samsung-phy.txt
Other common properties refer to
Documentation/devicetree/binding/pci/designware-pcie.txt
Example:
SoC specific DT Entry:
pcie@290000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x290000 0x1000
0x270000 0x1000
0x271000 0x40>;
interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
clocks = <&clock 28>, <&clock 27>;
clock-names = "pcie", "pcie_bus";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */
0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
num-lanes = <4>;
};
pcie@2a0000 {
compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
reg = <0x2a0000 0x1000
0x272000 0x1000
0x271040 0x40>;
interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
clocks = <&clock 29>, <&clock 27>;
clock-names = "pcie", "pcie_bus";
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */
0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
num-lanes = <4>;
};
With using PHY framework:
pcie_phy0: pcie-phy@270000 {
...
reg = <0x270000 0x1000>, <0x271000 0x40>;
reg-names = "phy", "block";
...
};
pcie@290000 {
...
reg = <0x290000 0x1000>, <0x40000000 0x1000>;
reg-names = "elbi", "config";
phys = <&pcie_phy0>;
ranges = <0x81000000 0 0 0x60001000 0 0x00010000
0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>;
...
};
Board specific DT Entry:
pcie@290000 {
reset-gpio = <&pin_ctrl 5 0>;
};
pcie@2a0000 {
reset-gpio = <&pin_ctrl 22 0>;
};
|
