| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
|
|
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
|
|
A user may call listen with binding an explicit port with the intent
that the kernel will assign an available port to the socket. In this
case inet_csk_get_port does a port scan. For such sockets, the user may
also set soreuseport with the intent a creating more sockets for the
port that is selected. The problem is that the initial socket being
opened could inadvertently choose an existing and unreleated port
number that was already created with soreuseport.
This patch adds a boolean parameter to inet_bind_conflict that indicates
rather soreuseport is allowed for the check (in addition to
sk->sk_reuseport). In calls to inet_bind_conflict from inet_csk_get_port
the argument is set to true if an explicit port is being looked up (snum
argument is nonzero), and is false if port scan is done.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
|
|
Commit 4f7df337fe79bba1e4c2d525525d63b5ba186bbd
"netlink: 2-clause nla_ok()" is BROKEN.
First clause tests if "->nla_len" could even be accessed at all,
it can not possibly be omitted.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
sk_drops can be an often written field, do not read it unless
application showed interest.
Note that sk_drops can be read via inet_diag, so applications
can avoid getting this info from every received packet.
In the future, 'reading' sk_drops might require folding per node or per
cpu fields, and thus become even more expensive than today.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFS is not commonly used, so add a jump label to avoid some conditionals
in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow dissection of ICMP(V6) type and code. This should only occur
if a packet is ICMP(V6) and the dissector has FLOW_DISSECTOR_KEY_ICMP set.
There are currently no users of FLOW_DISSECTOR_KEY_ICMP.
A follow-up patch will allow FLOW_DISSECTOR_KEY_ICMP to be used by
the flower classifier.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains a large Netfilter update for net-next,
to summarise:
1) Add support for stateful objects. This series provides a nf_tables
native alternative to the extended accounting infrastructure for
nf_tables. Two initial stateful objects are supported: counters and
quotas. Objects are identified by a user-defined name, you can fetch
and reset them anytime. You can also use a maps to allow fast lookups
using any arbitrary key combination. More info at:
http://marc.info/?l=netfilter-devel&m=148029128323837&w=2
2) On-demand registration of nf_conntrack and defrag hooks per netns.
Register nf_conntrack hooks if we have a stateful ruleset, ie.
state-based filtering or NAT. The new nf_conntrack_default_on sysctl
enables this from newly created netnamespaces. Default behaviour is not
modified. Patches from Florian Westphal.
3) Allocate 4k chunks and then use these for x_tables counter allocation
requests, this improves ruleset load time and also datapath ruleset
evaluation, patches from Florian Westphal.
4) Add support for ebpf to the existing x_tables bpf extension.
From Willem de Bruijn.
5) Update layer 4 checksum if any of the pseudoheader fields is updated.
This provides a limited form of 1:1 stateless NAT that make sense in
specific scenario, eg. load balancing.
6) Add support to flush sets in nf_tables. This series comes with a new
set->ops->deactivate_one() indirection given that we have to walk
over the list of set elements, then deactivate them one by one.
The existing set->ops->deactivate() performs an element lookup that
we don't need.
7) Two patches to avoid cloning packets, thus speed up packet forwarding
via nft_fwd from ingress. From Florian Westphal.
8) Two IPVS patches via Simon Horman: Decrement ttl in all modes to
prevent infinite loops, patch from Dwip Banerjee. And one minor
refactoring from Gao feng.
9) Revisit recent log support for nf_tables netdev families: One patch
to ensure that we correctly handle non-ethernet packets. Another
patch to add missing logger definition for netdev. Patches from
Liping Zhang.
10) Three patches for nft_fib, one to address insufficient register
initialization and another to solve incorrect (although harmless)
byteswap operation. Moreover update xt_rpfilter and nft_fib to match
lbcast packets with zeronet as source, eg. DHCP Discover packets
(0.0.0.0 -> 255.255.255.255). Also from Liping Zhang.
11) Built-in DCCP, SCTP and UDPlite conntrack and NAT support, from
Davide Caratti. While DCCP is rather hopeless lately, and UDPlite has
been broken in many-cast mode for some little time, let's give them a
chance by placing them at the same level as other existing protocols.
Thus, users don't explicitly have to modprobe support for this and
NAT rules work for them. Some people point to the lack of support in
SOHO Linux-based routers that make deployment of new protocols harder.
I guess other middleboxes outthere on the Internet are also to blame.
Anyway, let's see if this has any impact in the midrun.
12) Skip software SCTP software checksum calculation if the NIC comes
with SCTP checksum offload support. From Davide Caratti.
13) Initial core factoring to prepare conversion to hook array. Three
patches from Aaron Conole.
14) Gao Feng made a wrong conversion to switch in the xt_multiport
extension in a patch coming in the previous batch. Fix it in this
batch.
15) Get vmalloc call in sync with kmalloc flags to avoid a warning
and likely OOM killer intervention from x_tables. From Marcelo
Ricardo Leitner.
16) Update Arturo Borrero's email address in all source code headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo noticed a cache line miss in UDP recvmsg() to access
sk_rxhash, sharing a cache line with sk_drops.
sk_drops might be heavily incremented by cpus handling a flood targeting
this socket.
We might place sk_drops on a separate cache line, but lets try
to avoid wasting 64 bytes per socket just for this, since we have
other bottlenecks to take care of.
sock_rps_record_flow() should only access sk_rxhash for connected
flows.
Testing sk_state for TCP_ESTABLISHED covers most of the cases for
connected sockets, for a zero cost, since system calls using
sock_rps_record_flow() also access sk->sk_prot which is on the
same cache line.
A follow up patch will provide a static_key (Jump Label) since most
hosts do not even use RFS.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for set flushing, that consists of walking over
the set elements if the NFTA_SET_ELEM_LIST_ELEMENTS attribute is set.
This patch requires the following changes:
1) Add set->ops->deactivate_one() operation: This allows us to
deactivate an element from the set element walk path, given we can
skip the lookup that happens in ->deactivate().
2) Add a new nft_trans_alloc_gfp() function since we need to allocate
transactions using GFP_ATOMIC given the set walk path happens with
held rcu_read_lock.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch allows you to refer to stateful objects from set elements.
This provides the infrastructure to create maps where the right hand
side of the mapping is a stateful object.
This allows us to build dictionaries of stateful objects, that you can
use to perform fast lookups using any arbitrary key combination.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Notify on depleted quota objects. The NFT_QUOTA_F_DEPLETED flag
indicates we have reached overquota.
Add pointer to table from nft_object, so we can use it when sending the
depletion notification to userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Introduce nf_tables_obj_notify() to notify internal state changes in
stateful objects. This is used by the quota object to report depletion
in a follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds a new NFT_MSG_GETOBJ_RESET command perform an atomic
dump-and-reset of the stateful object. This also comes with add support
for atomic dump and reset for counter and quota objects.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch augments nf_tables to support stateful objects. This new
infrastructure allows you to create, dump and delete stateful objects,
that are identified by a user-defined name.
This patch adds the generic infrastructure, follow up patches add
support for two stateful objects: counters and quotas.
This patch provides a native infrastructure for nf_tables to replace
nfacct, the extended accounting infrastructure for iptables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
... so we can use current skb instead of working with a clone.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds a new flag that signals the kernel to update layer 4
checksum if the packet field belongs to the layer 4 pseudoheader. This
implicitly provides stateless NAT 1:1 that is useful under very specific
usecases.
Since rules mangling layer 3 fields that are part of the pseudoheader
may potentially convey any layer 4 packet, we have to deal with the
layer 4 checksum adjustment using protocol specific code.
This patch adds support for TCP, UDP and ICMPv6, since they include the
pseudoheader in the layer 4 checksum calculation. ICMP doesn't, so we
can skip it.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
nf_defrag modules for ipv4 and ipv6 export an empty stub function.
Any module that needs the defragmentation hooks registered simply 'calls'
this empty function to create a phony module dependency -- modprobe will
then load the defrag module too.
This extends netfilter ipv4/ipv6 defragmentation modules to delay the hook
registration until the functionality is requested within a network namespace
instead of module load time for all namespaces.
Hooks are only un-registered on module unload or when a namespace that used
such defrag functionality exits.
We have to use struct net for this as the register hooks can be called
before netns initialization here from the ipv4/ipv6 conntrack module
init path.
There is no unregister functionality support, defrag will always be
active once it was requested inside a net namespace.
The reason is that defrag has impact on nft and iptables rulesets
(without defrag we might see framents).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
1) Old code was hard to maintain, due to complex lock chains.
(We probably will be able to remove some kfree_rcu() in callers)
2) Using a single timer to update all estimators does not scale.
3) Code was buggy on 32bit kernel (WRITE_ONCE() on 64bit quantity
is not supposed to work well)
In this rewrite :
- I removed the RB tree that had to be scanned in
gen_estimator_active(). qdisc dumps should be much faster.
- Each estimator has its own timer.
- Estimations are maintained in net_rate_estimator structure,
instead of dirtying the qdisc. Minor, but part of the simplification.
- Reading the estimator uses RCU and a seqcount to provide proper
support for 32bit kernels.
- We reduce memory need when estimators are not used, since
we store a pointer, instead of the bytes/packets counters.
- xt_rateest_mt() no longer has to grab a spinlock.
(In the future, xt_rateest_tg() could be switched to per cpu counters)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
on success
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-12-03
Here's a set of Bluetooth & 802.15.4 patches for net-next (i.e. 4.10
kernel):
- Fix for a potential NULL deref in the ieee802154 netlink code
- Fix for the ED values of the at86rf2xx driver
- Documentation updates to ieee802154
- Cleanups to u8 vs __u8 usage
- Timer API usage cleanups in HCI drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Group fields used in TX path, and keep some cache lines mostly read
to permit sharing among cpus.
Gained two 4 bytes holes on 64bit arches.
Added a place holder for tcp tsq_flags, next to sk_wmem_alloc
to speed up tcp_wfree() in the following patch.
I have not added ____cacheline_aligned_in_smp, this might be done later.
I prefer doing this once inet and tcp/udp sockets reorg is also done.
Tested with both TCP and UDP.
UDP receiver performance under flood increased by ~20 % :
Accessing sk_filter/sk_wq/sk_napi_id no longer stalls because sk_drops
was moved away from a critical cache line, now mostly read and shared.
/* --- cacheline 4 boundary (256 bytes) --- */
unsigned int sk_napi_id; /* 0x100 0x4 */
int sk_rcvbuf; /* 0x104 0x4 */
struct sk_filter * sk_filter; /* 0x108 0x8 */
union {
struct socket_wq * sk_wq; /* 0x8 */
struct socket_wq * sk_wq_raw; /* 0x8 */
}; /* 0x110 0x8 */
struct xfrm_policy * sk_policy[2]; /* 0x118 0x10 */
struct dst_entry * sk_rx_dst; /* 0x128 0x8 */
struct dst_entry * sk_dst_cache; /* 0x130 0x8 */
atomic_t sk_omem_alloc; /* 0x138 0x4 */
int sk_sndbuf; /* 0x13c 0x4 */
/* --- cacheline 5 boundary (320 bytes) --- */
int sk_wmem_queued; /* 0x140 0x4 */
atomic_t sk_wmem_alloc; /* 0x144 0x4 */
long unsigned int sk_tsq_flags; /* 0x148 0x8 */
struct sk_buff * sk_send_head; /* 0x150 0x8 */
struct sk_buff_head sk_write_queue; /* 0x158 0x18 */
__s32 sk_peek_off; /* 0x170 0x4 */
int sk_write_pending; /* 0x174 0x4 */
long int sk_sndtimeo; /* 0x178 0x8 */
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switch (default on) can be used to disable automatic registration
of connection tracking functionality in newly created network
namespaces.
This means that when net namespace goes down (or the tracker protocol
module is unloaded) we *might* have to unregister the hooks.
We can either add another per-netns variable that tells if
the hooks got registered by default, or, alternatively, just call
the protocol _put() function and have the callee deal with a possible
'extra' put() operation that doesn't pair with a get() one.
This uses the latter approach, i.e. a put() without a get has no effect.
Conntrack is still enabled automatically regardless of the new sysctl
setting if the new net namespace requires connection tracking, e.g. when
NAT rules are created.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This makes use of nf_ct_netns_get/put added in previous patch.
We add get/put functions to nf_conntrack_l3proto structure, ipv4 and ipv6
then implement use-count to track how many users (nft or xtables modules)
have a dependency on ipv4 and/or ipv6 connection tracking functionality.
When count reaches zero, the hooks are unregistered.
This delays activation of connection tracking inside a namespace until
stateful firewall rule or nat rule gets added.
This patch breaks backwards compatibility in the sense that connection
tracking won't be active anymore when the protocol tracker module is
loaded. This breaks e.g. setups that ctnetlink for flow accounting and
the like, without any '-m conntrack' packet filter rules.
Followup patch restores old behavour and makes new delayed scheme
optional via sysctl.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
currently aliased to try_module_get/_put.
Will be changed in next patch when we add functions to make use of ->net
argument to store usercount per l3proto tracker.
This is needed to avoid registering the conntrack hooks in all netns and
later only enable connection tracking in those that need conntrack.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
since adf0516845bcd0 ("netfilter: remove ip_conntrack* sysctl compat code")
the only user (ipv4 tracker) sets this to an empty stub function.
After this change nf_ct_l3proto_pernet_register() is also empty,
but this will change in a followup patch to add conditional register
of the hooks.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_CT_PROTO_UDPLITE is no more a tristate. When set to y,
connection tracking support for UDPlite protocol is built-in into
nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_udplite,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| udplite| ipv4 | ipv6 |nf_conntrack
---------++--------+--------+--------+--------------
none || 432538 | 828755 | 828676 | 6141434
UDPlite || - | 829649 | 829362 | 6498204
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_CT_PROTO_SCTP is no more a tristate. When set to y, connection
tracking support for SCTP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_sctp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| sctp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 498243 | 828755 | 828676 | 6141434
SCTP || - | 829254 | 829175 | 6547872
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_CT_PROTO_DCCP is no more a tristate. When set to y, connection
tracking support for DCCP protocol is built-in into nf_conntrack.ko.
footprint test:
$ ls -l net/netfilter/nf_conntrack{_proto_dccp,}.ko \
net/ipv4/netfilter/nf_conntrack_ipv4.ko \
net/ipv6/netfilter/nf_conntrack_ipv6.ko
(builtin)|| dccp | ipv4 | ipv6 | nf_conntrack
---------++--------+--------+--------+--------------
none || 469140 | 828755 | 828676 | 6141434
DCCP || - | 830566 | 829935 | 6533526
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In netdev family, we will handle non ethernet packets, so using
eth_hdr(skb)->h_proto is incorrect.
Meanwhile, we can use socket(AF_PACKET...) to sending packets, so
skb->protocol is not always set in bridge family.
Add an extra parameter into nf_log_l2packet to solve this issue.
Fixes: 1fddf4bad0ac ("netfilter: nf_log: add packet logging for netdev family")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_NAT_PROTO_UDPLITE is no more a tristate. When set to y, NAT
support for UDPlite protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) |udplite || nf_nat
--------------------------+--------++--------
no builtin | 408048 || 2241312
UDPLITE builtin | - || 2577256
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_NAT_PROTO_SCTP is no more a tristate. When set to y, NAT
support for SCTP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | sctp || nf_nat
--------------------------+--------++--------
no builtin | 428344 || 2241312
SCTP builtin | - || 2597032
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
CONFIG_NF_NAT_PROTO_DCCP is no more a tristate. When set to y, NAT
support for DCCP protocol is built-in into nf_nat.ko.
footprint test:
(nf_nat_proto_) | dccp || nf_nat
--------------------------+--------++--------
no builtin | 409800 || 2241312
DCCP builtin | - || 2578968
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b90eb7549499 ("fib: introduce FIB notification infrastructure")
introduced a new notification chain to notify listeners (f.e., switchdev
drivers) about addition and deletion of routes.
However, upon registration to the chain the FIB tables can already be
populated, which means potential listeners will have an incomplete view
of the tables.
Solve that by dumping the FIB tables and replaying the events to the
passed notification block. The dump itself is done using RCU in order
not to starve consumers that need RTNL to make progress.
The integrity of the dump is ensured by reading the FIB change sequence
counter before and after the dump under RTNL. This allows us to avoid
the problematic situation in which the dumping process sends a ENTRY_ADD
notification following ENTRY_DEL generated by another process holding
RTNL.
Callers of the registration function may pass a callback that is
executed in case the dump was inconsistent with current FIB tables.
The number of retries until a consistent dump is achieved is set to a
fixed number to prevent callers from looping for long periods of time.
In case current limit proves to be problematic in the future, it can be
easily converted to be configurable using a sysctl.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch will enable listeners of the FIB notification chain to
request a dump of the FIB tables. However, since RTNL isn't taken during
the dump, it's possible for the FIB tables to change mid-dump, which
will result in inconsistency between the listener's table and the
kernel's.
Allow listeners to know about changes that occurred mid-dump, by adding
a change sequence counter to each net namespace. The counter is
incremented just before a notification is sent in the FIB chain.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in the previous commit, modules are going to need to take a
reference on fib info and then drop it using fib_info_put().
Add the fib_info_hold() helper to make the code more readable and also
symmetric with fib_info_put().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net_generic() function is both a) inline and b) used ~600 times.
It has the following code inside
...
ptr = ng->ptr[id - 1];
...
"id" is never compile time constant so compiler is forced to subtract 1.
And those decrements or LEA [r32 - 1] instructions add up.
We also start id'ing from 1 to catch bugs where pernet sybsystem id
is not initialized and 0. This is quite pointless idea (nothing will
work or immediate interference with first registered subsystem) in
general but it hints what needs to be done for code size reduction.
Namely, overlaying allocation of pointer array and fixed part of
structure in the beginning and using usual base-0 addressing.
Ids are just cookies, their exact values do not matter, so lets start
with 3 on x86_64.
Code size savings (oh boy): -4.2 KB
As usual, ignore the initial compiler stupidity part of the table.
add/remove: 0/0 grow/shrink: 12/670 up/down: 89/-4297 (-4208)
function old new delta
tipc_nametbl_insert_publ 1250 1270 +20
nlmclnt_lookup_host 686 703 +17
nfsd4_encode_fattr 5930 5941 +11
nfs_get_client 1050 1061 +11
register_pernet_operations 333 342 +9
tcf_mirred_init 843 849 +6
tcf_bpf_init 1143 1149 +6
gss_setup_upcall 990 994 +4
idmap_name_to_id 432 434 +2
ops_init 274 275 +1
nfsd_inject_forget_client 259 260 +1
nfs4_alloc_client 612 613 +1
tunnel_key_walker 164 163 -1
...
tipc_bcbase_select_primary 392 360 -32
mac80211_hwsim_new_radio 2808 2767 -41
ipip6_tunnel_ioctl 2228 2186 -42
tipc_bcast_rcv 715 672 -43
tipc_link_build_proto_msg 1140 1089 -51
nfsd4_lock 3851 3796 -55
tipc_mon_rcv 1012 956 -56
Total: Before=156643951, After=156639743, chg -0.00%
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is precursor to fixing "[id - 1]" bloat inside net_generic().
Name "s" is chosen to complement name "u" often used for dummy unions.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nla_ok() consists of 3 clauses:
1) int rem >= (int)sizeof(struct nlattr)
2) u16 nla_len >= sizeof(struct nlattr)
3) u16 nla_len <= int rem
The statement is that clause (1) is redundant.
What it does is ensuring that "rem" is a positive number,
so that in clause (3) positive number will be compared to positive number
with no problems.
However, "u16" fully fits into "int" and integers do not change value
when upcasting even to signed type. Negative integers will be rejected
by clause (3) just fine. Small positive integers will be rejected
by transitivity of comparison operator.
NOTE: all of the above DOES NOT apply to nlmsg_ok() where ->nlmsg_len is
u32(!), so 3 clauses AND A CAST TO INT are necessary.
Obligatory space savings report: -1.6 KB
$ ./scripts/bloat-o-meter ../vmlinux-000* ../vmlinux-001*
add/remove: 0/0 grow/shrink: 3/63 up/down: 35/-1692 (-1657)
function old new delta
validate_scan_freqs 142 155 +13
tcf_em_tree_validate 867 879 +12
dcbnl_ieee_del 328 338 +10
netlbl_cipsov4_add_common.isra 218 215 -3
...
ovs_nla_put_actions 888 806 -82
netlbl_cipsov4_add_std 1648 1566 -82
nl80211_parse_sched_scan 2889 2780 -109
ip_tun_from_nlattr 3086 2945 -141
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add socket family, type and protocol to bpf_sock allowing bpf programs
read-only access.
Add __sk_flags_offset[0] to struct sock before the bitfield to
programmtically determine the offset of the unsigned int containing
protocol and type.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
