From 87f966d97b89774162df04d2106c6350c8fe4cb3 Mon Sep 17 00:00:00 2001 From: Markos Chandras Date: Thu, 19 Mar 2015 10:28:14 +0000 Subject: net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5} On a MIPS Malta board, tons of fifo underflow errors have been observed when using u-boot as bootloader instead of YAMON. The reason for that is that YAMON used to set the pcnet device to SRAM mode but u-boot does not. As a result, the default Tx threshold (64 bytes) is now too small to keep the fifo relatively used and it can result to Tx fifo underflow errors. As a result of which, it's best to setup the SRAM on supported controllers so we can always use the NOUFLO bit. Cc: Cc: Cc: Cc: Don Fry Signed-off-by: Markos Chandras Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/pcnet32.c | 31 +++++++++++++++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/amd/pcnet32.c b/drivers/net/ethernet/amd/pcnet32.c index 11d6e6561df1..15a8190a6f75 100644 --- a/drivers/net/ethernet/amd/pcnet32.c +++ b/drivers/net/ethernet/amd/pcnet32.c @@ -1543,7 +1543,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) { struct pcnet32_private *lp; int i, media; - int fdx, mii, fset, dxsuflo; + int fdx, mii, fset, dxsuflo, sram; int chip_version; char *chipname; struct net_device *dev; @@ -1580,7 +1580,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) } /* initialize variables */ - fdx = mii = fset = dxsuflo = 0; + fdx = mii = fset = dxsuflo = sram = 0; chip_version = (chip_version >> 12) & 0xffff; switch (chip_version) { @@ -1613,6 +1613,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) chipname = "PCnet/FAST III 79C973"; /* PCI */ fdx = 1; mii = 1; + sram = 1; break; case 0x2626: chipname = "PCnet/Home 79C978"; /* PCI */ @@ -1636,6 +1637,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) chipname = "PCnet/FAST III 79C975"; /* PCI */ fdx = 1; mii = 1; + sram = 1; break; case 0x2628: chipname = "PCnet/PRO 79C976"; @@ -1664,6 +1666,31 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) dxsuflo = 1; } + /* + * The Am79C973/Am79C975 controllers come with 12K of SRAM + * which we can use for the Tx/Rx buffers but most importantly, + * the use of SRAM allow us to use the BCR18:NOUFLO bit to avoid + * Tx fifo underflows. + */ + if (sram) { + /* + * The SRAM is being configured in two steps. First we + * set the SRAM size in the BCR25:SRAM_SIZE bits. According + * to the datasheet, each bit corresponds to a 512-byte + * page so we can have at most 24 pages. The SRAM_SIZE + * holds the value of the upper 8 bits of the 16-bit SRAM size. + * The low 8-bits start at 0x00 and end at 0xff. So the + * address range is from 0x0000 up to 0x17ff. Therefore, + * the SRAM_SIZE is set to 0x17. The next step is to set + * the BCR26:SRAM_BND midway through so the Tx and Rx + * buffers can share the SRAM equally. + */ + a->write_bcr(ioaddr, 25, 0x17); + a->write_bcr(ioaddr, 26, 0xc); + /* And finally enable the NOUFLO bit */ + a->write_bcr(ioaddr, 18, a->read_bcr(ioaddr, 18) | (1 << 11)); + } + dev = alloc_etherdev(sizeof(*lp)); if (!dev) { ret = -ENOMEM; -- cgit v1.2.3 From 435452aa88474fae5a31fd14fca88f0802e66f53 Mon Sep 17 00:00:00 2001 From: Vasundhara Volam Date: Fri, 20 Mar 2015 06:28:23 -0400 Subject: be2net: Prevent VFs from enabling VLAN promiscuous mode Currently, a PF does not restrict its VF interface from enabling vlan promiscuous mode. This breaks vlan isolation when a vlan (transparent tagging) is configured on a VF. This patch fixes this problem by disabling the vlan promisc capability for VFs. Reported-by: Yoann Juet Signed-off-by: Vasundhara Volam Signed-off-by: Sathya Perla Signed-off-by: David S. Miller --- drivers/net/ethernet/emulex/benet/be.h | 1 + drivers/net/ethernet/emulex/benet/be_cmds.c | 3 +- drivers/net/ethernet/emulex/benet/be_cmds.h | 2 +- drivers/net/ethernet/emulex/benet/be_main.c | 98 ++++++++++++++++++++++------- 4 files changed, 80 insertions(+), 24 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h index 27de37aa90af..92eb0c82bb04 100644 --- a/drivers/net/ethernet/emulex/benet/be.h +++ b/drivers/net/ethernet/emulex/benet/be.h @@ -354,6 +354,7 @@ struct be_vf_cfg { u16 vlan_tag; u32 tx_rate; u32 plink_tracking; + u32 privileges; }; enum vf_state { diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c index 36916cfa70f9..3e894f449cc1 100644 --- a/drivers/net/ethernet/emulex/benet/be_cmds.c +++ b/drivers/net/ethernet/emulex/benet/be_cmds.c @@ -1918,7 +1918,7 @@ int be_cmd_modify_eqd(struct be_adapter *adapter, struct be_set_eqd *set_eqd, /* Uses sycnhronous mcc */ int be_cmd_vlan_config(struct be_adapter *adapter, u32 if_id, u16 *vtag_array, - u32 num) + u32 num, u32 domain) { struct be_mcc_wrb *wrb; struct be_cmd_req_vlan_config *req; @@ -1936,6 +1936,7 @@ int be_cmd_vlan_config(struct be_adapter *adapter, u32 if_id, u16 *vtag_array, be_wrb_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_COMMON, OPCODE_COMMON_NTWK_VLAN_CONFIG, sizeof(*req), wrb, NULL); + req->hdr.domain = domain; req->interface_id = if_id; req->untagged = BE_IF_FLAGS_UNTAGGED & be_if_cap_flags(adapter) ? 1 : 0; diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.h b/drivers/net/ethernet/emulex/benet/be_cmds.h index db761e8e42a3..a7634a3f052a 100644 --- a/drivers/net/ethernet/emulex/benet/be_cmds.h +++ b/drivers/net/ethernet/emulex/benet/be_cmds.h @@ -2256,7 +2256,7 @@ int lancer_cmd_get_pport_stats(struct be_adapter *adapter, int be_cmd_get_fw_ver(struct be_adapter *adapter); int be_cmd_modify_eqd(struct be_adapter *adapter, struct be_set_eqd *, int num); int be_cmd_vlan_config(struct be_adapter *adapter, u32 if_id, u16 *vtag_array, - u32 num); + u32 num, u32 domain); int be_cmd_rx_filter(struct be_adapter *adapter, u32 flags, u32 status); int be_cmd_set_flow_control(struct be_adapter *adapter, u32 tx_fc, u32 rx_fc); int be_cmd_get_flow_control(struct be_adapter *adapter, u32 *tx_fc, u32 *rx_fc); diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c index 0a816859aca5..eb2bed92bf60 100644 --- a/drivers/net/ethernet/emulex/benet/be_main.c +++ b/drivers/net/ethernet/emulex/benet/be_main.c @@ -1171,7 +1171,7 @@ static int be_vid_config(struct be_adapter *adapter) for_each_set_bit(i, adapter->vids, VLAN_N_VID) vids[num++] = cpu_to_le16(i); - status = be_cmd_vlan_config(adapter, adapter->if_handle, vids, num); + status = be_cmd_vlan_config(adapter, adapter->if_handle, vids, num, 0); if (status) { dev_err(dev, "Setting HW VLAN filtering failed\n"); /* Set to VLAN promisc mode as setting VLAN filter failed */ @@ -1380,11 +1380,67 @@ static int be_get_vf_config(struct net_device *netdev, int vf, return 0; } +static int be_set_vf_tvt(struct be_adapter *adapter, int vf, u16 vlan) +{ + struct be_vf_cfg *vf_cfg = &adapter->vf_cfg[vf]; + u16 vids[BE_NUM_VLANS_SUPPORTED]; + int vf_if_id = vf_cfg->if_handle; + int status; + + /* Enable Transparent VLAN Tagging */ + status = be_cmd_set_hsw_config(adapter, vlan, vf + 1, vf_if_id, 0); + if (status) + return status; + + /* Clear pre-programmed VLAN filters on VF if any, if TVT is enabled */ + vids[0] = 0; + status = be_cmd_vlan_config(adapter, vf_if_id, vids, 1, vf + 1); + if (!status) + dev_info(&adapter->pdev->dev, + "Cleared guest VLANs on VF%d", vf); + + /* After TVT is enabled, disallow VFs to program VLAN filters */ + if (vf_cfg->privileges & BE_PRIV_FILTMGMT) { + status = be_cmd_set_fn_privileges(adapter, vf_cfg->privileges & + ~BE_PRIV_FILTMGMT, vf + 1); + if (!status) + vf_cfg->privileges &= ~BE_PRIV_FILTMGMT; + } + return 0; +} + +static int be_clear_vf_tvt(struct be_adapter *adapter, int vf) +{ + struct be_vf_cfg *vf_cfg = &adapter->vf_cfg[vf]; + struct device *dev = &adapter->pdev->dev; + int status; + + /* Reset Transparent VLAN Tagging. */ + status = be_cmd_set_hsw_config(adapter, BE_RESET_VLAN_TAG_ID, vf + 1, + vf_cfg->if_handle, 0); + if (status) + return status; + + /* Allow VFs to program VLAN filtering */ + if (!(vf_cfg->privileges & BE_PRIV_FILTMGMT)) { + status = be_cmd_set_fn_privileges(adapter, vf_cfg->privileges | + BE_PRIV_FILTMGMT, vf + 1); + if (!status) { + vf_cfg->privileges |= BE_PRIV_FILTMGMT; + dev_info(dev, "VF%d: FILTMGMT priv enabled", vf); + } + } + + dev_info(dev, + "Disable/re-enable i/f in VM to clear Transparent VLAN tag"); + return 0; +} + static int be_set_vf_vlan(struct net_device *netdev, int vf, u16 vlan, u8 qos) { struct be_adapter *adapter = netdev_priv(netdev); struct be_vf_cfg *vf_cfg = &adapter->vf_cfg[vf]; - int status = 0; + int status; if (!sriov_enabled(adapter)) return -EPERM; @@ -1394,24 +1450,19 @@ static int be_set_vf_vlan(struct net_device *netdev, int vf, u16 vlan, u8 qos) if (vlan || qos) { vlan |= qos << VLAN_PRIO_SHIFT; - if (vf_cfg->vlan_tag != vlan) - status = be_cmd_set_hsw_config(adapter, vlan, vf + 1, - vf_cfg->if_handle, 0); + status = be_set_vf_tvt(adapter, vf, vlan); } else { - /* Reset Transparent Vlan Tagging. */ - status = be_cmd_set_hsw_config(adapter, BE_RESET_VLAN_TAG_ID, - vf + 1, vf_cfg->if_handle, 0); + status = be_clear_vf_tvt(adapter, vf); } if (status) { dev_err(&adapter->pdev->dev, - "VLAN %d config on VF %d failed : %#x\n", vlan, - vf, status); + "VLAN %d config on VF %d failed : %#x\n", vlan, vf, + status); return be_cmd_status(status); } vf_cfg->vlan_tag = vlan; - return 0; } @@ -3339,7 +3390,6 @@ static int be_if_create(struct be_adapter *adapter, u32 *if_handle, u32 cap_flags, u32 vf) { u32 en_flags; - int status; en_flags = BE_IF_FLAGS_UNTAGGED | BE_IF_FLAGS_BROADCAST | BE_IF_FLAGS_MULTICAST | BE_IF_FLAGS_PASS_L3L4_ERRORS | @@ -3347,10 +3397,7 @@ static int be_if_create(struct be_adapter *adapter, u32 *if_handle, en_flags &= cap_flags; - status = be_cmd_if_create(adapter, cap_flags, en_flags, - if_handle, vf); - - return status; + return be_cmd_if_create(adapter, cap_flags, en_flags, if_handle, vf); } static int be_vfs_if_create(struct be_adapter *adapter) @@ -3368,8 +3415,13 @@ static int be_vfs_if_create(struct be_adapter *adapter) if (!BE3_chip(adapter)) { status = be_cmd_get_profile_config(adapter, &res, vf + 1); - if (!status) + if (!status) { cap_flags = res.if_cap_flags; + /* Prevent VFs from enabling VLAN promiscuous + * mode + */ + cap_flags &= ~BE_IF_FLAGS_VLAN_PROMISCUOUS; + } } status = be_if_create(adapter, &vf_cfg->if_handle, @@ -3403,7 +3455,6 @@ static int be_vf_setup(struct be_adapter *adapter) struct device *dev = &adapter->pdev->dev; struct be_vf_cfg *vf_cfg; int status, old_vfs, vf; - u32 privileges; old_vfs = pci_num_vf(adapter->pdev); @@ -3433,15 +3484,18 @@ static int be_vf_setup(struct be_adapter *adapter) for_all_vfs(adapter, vf_cfg, vf) { /* Allow VFs to programs MAC/VLAN filters */ - status = be_cmd_get_fn_privileges(adapter, &privileges, vf + 1); - if (!status && !(privileges & BE_PRIV_FILTMGMT)) { + status = be_cmd_get_fn_privileges(adapter, &vf_cfg->privileges, + vf + 1); + if (!status && !(vf_cfg->privileges & BE_PRIV_FILTMGMT)) { status = be_cmd_set_fn_privileges(adapter, - privileges | + vf_cfg->privileges | BE_PRIV_FILTMGMT, vf + 1); - if (!status) + if (!status) { + vf_cfg->privileges |= BE_PRIV_FILTMGMT; dev_info(dev, "VF%d has FILTMGMT privilege\n", vf); + } } /* Allow full available bandwidth */ -- cgit v1.2.3 From c8ba4ad0b59c511578f8f706aae711f01c990794 Mon Sep 17 00:00:00 2001 From: Suresh Reddy Date: Fri, 20 Mar 2015 06:28:24 -0400 Subject: be2net: restrict MODIFY_EQ_DELAY cmd to a max of 8 EQs Issuing this cmd for more than 8 EQs does not have the intended effect even on BEx and Skyhawk-R. This patch fixes this by issuing this cmd for upto 8 EQs at a time. Signed-off-by: Suresh Reddy Signed-off-by: Sathya Perla Signed-off-by: David S. Miller --- drivers/net/ethernet/emulex/benet/be_cmds.c | 14 +++++--------- 1 file changed, 5 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/emulex/benet/be_cmds.c b/drivers/net/ethernet/emulex/benet/be_cmds.c index 3e894f449cc1..7f05f309e935 100644 --- a/drivers/net/ethernet/emulex/benet/be_cmds.c +++ b/drivers/net/ethernet/emulex/benet/be_cmds.c @@ -1902,15 +1902,11 @@ int be_cmd_modify_eqd(struct be_adapter *adapter, struct be_set_eqd *set_eqd, { int num_eqs, i = 0; - if (lancer_chip(adapter) && num > 8) { - while (num) { - num_eqs = min(num, 8); - __be_cmd_modify_eqd(adapter, &set_eqd[i], num_eqs); - i += num_eqs; - num -= num_eqs; - } - } else { - __be_cmd_modify_eqd(adapter, set_eqd, num); + while (num) { + num_eqs = min(num, 8); + __be_cmd_modify_eqd(adapter, &set_eqd[i], num_eqs); + i += num_eqs; + num -= num_eqs; } return 0; -- cgit v1.2.3 From 25848c9015964d9d97dffd48bbb88b75a25d0a1b Mon Sep 17 00:00:00 2001 From: Suresh Reddy Date: Fri, 20 Mar 2015 06:28:25 -0400 Subject: be2net: use PCI MMIO read instead of config read for errors When an EEH error occurs, the device/slot is disconnected. This condition is more reliably detected (i.e., returns all ones) with an MMIO read rather than a config read -- especially on power platforms. Hence, this patch fixes EEH error detection by replacing config reads with MMIO reads for reading the error registers. The error registers in Skyhawk-R/BE2/BE3 are accessible both via the config space and the PCICFG (BAR0) memory space. Reported-by: Gavin Shan Signed-off-by: Suresh Reddy Signed-off-by: Sathya Perla Signed-off-by: David S. Miller --- drivers/net/ethernet/emulex/benet/be.h | 1 + drivers/net/ethernet/emulex/benet/be_main.c | 33 +++++++++++++++++++---------- 2 files changed, 23 insertions(+), 11 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h index 92eb0c82bb04..27b9fe99a9bd 100644 --- a/drivers/net/ethernet/emulex/benet/be.h +++ b/drivers/net/ethernet/emulex/benet/be.h @@ -424,6 +424,7 @@ struct be_adapter { u8 __iomem *csr; /* CSR BAR used only for BE2/3 */ u8 __iomem *db; /* Door Bell */ + u8 __iomem *pcicfg; /* On SH,BEx only. Shadow of PCI config space */ struct mutex mbox_lock; /* For serializing mbox cmds to BE card */ struct be_dma_mem mbox_mem; diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c index eb2bed92bf60..e6b790f0d9dc 100644 --- a/drivers/net/ethernet/emulex/benet/be_main.c +++ b/drivers/net/ethernet/emulex/benet/be_main.c @@ -2823,14 +2823,12 @@ void be_detect_error(struct be_adapter *adapter) } } } else { - pci_read_config_dword(adapter->pdev, - PCICFG_UE_STATUS_LOW, &ue_lo); - pci_read_config_dword(adapter->pdev, - PCICFG_UE_STATUS_HIGH, &ue_hi); - pci_read_config_dword(adapter->pdev, - PCICFG_UE_STATUS_LOW_MASK, &ue_lo_mask); - pci_read_config_dword(adapter->pdev, - PCICFG_UE_STATUS_HI_MASK, &ue_hi_mask); + ue_lo = ioread32(adapter->pcicfg + PCICFG_UE_STATUS_LOW); + ue_hi = ioread32(adapter->pcicfg + PCICFG_UE_STATUS_HIGH); + ue_lo_mask = ioread32(adapter->pcicfg + + PCICFG_UE_STATUS_LOW_MASK); + ue_hi_mask = ioread32(adapter->pcicfg + + PCICFG_UE_STATUS_HI_MASK); ue_lo = (ue_lo & ~ue_lo_mask); ue_hi = (ue_hi & ~ue_hi_mask); @@ -4874,24 +4872,37 @@ static int be_roce_map_pci_bars(struct be_adapter *adapter) static int be_map_pci_bars(struct be_adapter *adapter) { + struct pci_dev *pdev = adapter->pdev; u8 __iomem *addr; if (BEx_chip(adapter) && be_physfn(adapter)) { - adapter->csr = pci_iomap(adapter->pdev, 2, 0); + adapter->csr = pci_iomap(pdev, 2, 0); if (!adapter->csr) return -ENOMEM; } - addr = pci_iomap(adapter->pdev, db_bar(adapter), 0); + addr = pci_iomap(pdev, db_bar(adapter), 0); if (!addr) goto pci_map_err; adapter->db = addr; + if (skyhawk_chip(adapter) || BEx_chip(adapter)) { + if (be_physfn(adapter)) { + /* PCICFG is the 2nd BAR in BE2 */ + addr = pci_iomap(pdev, BE2_chip(adapter) ? 1 : 0, 0); + if (!addr) + goto pci_map_err; + adapter->pcicfg = addr; + } else { + adapter->pcicfg = adapter->db + SRIOV_VF_PCICFG_OFFSET; + } + } + be_roce_map_pci_bars(adapter); return 0; pci_map_err: - dev_err(&adapter->pdev->dev, "Error in mapping PCI BARs\n"); + dev_err(&pdev->dev, "Error in mapping PCI BARs\n"); be_unmap_pci_bars(adapter); return -ENOMEM; } -- cgit v1.2.3 From f40bff4239d45ac061044a8a79cf6868c62df345 Mon Sep 17 00:00:00 2001 From: Ondrej Zary Date: Sat, 21 Mar 2015 11:29:37 +0100 Subject: cx82310_eth: wait for firmware to become ready When the device is powered up, some (older) firmware versions fail to work properly if we send commands before the boot is complete (everything is OK when the device is hot-plugged). The firmware indicates its ready status by putting the link up. Newer firmwares delay the first command so they don't suffer from this problem. They also report the link being always up. Wait for firmware to become ready (link up) before sending any commands and/or data. This also allows lowering CMD_TIMEOUT value to a reasonable time. Tested with 4.1.0.9 (old) and 4.1.0.30 (new) firmware versions. Signed-off-by: Ondrej Zary Signed-off-by: David S. Miller --- drivers/net/usb/cx82310_eth.c | 30 ++++++++++++++++++++++++------ 1 file changed, 24 insertions(+), 6 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/cx82310_eth.c b/drivers/net/usb/cx82310_eth.c index fe48f4c51373..1762ad3910b2 100644 --- a/drivers/net/usb/cx82310_eth.c +++ b/drivers/net/usb/cx82310_eth.c @@ -46,8 +46,7 @@ enum cx82310_status { }; #define CMD_PACKET_SIZE 64 -/* first command after power on can take around 8 seconds */ -#define CMD_TIMEOUT 15000 +#define CMD_TIMEOUT 100 #define CMD_REPLY_RETRY 5 #define CX82310_MTU 1514 @@ -78,8 +77,9 @@ static int cx82310_cmd(struct usbnet *dev, enum cx82310_cmd cmd, bool reply, ret = usb_bulk_msg(udev, usb_sndbulkpipe(udev, CMD_EP), buf, CMD_PACKET_SIZE, &actual_len, CMD_TIMEOUT); if (ret < 0) { - dev_err(&dev->udev->dev, "send command %#x: error %d\n", - cmd, ret); + if (cmd != CMD_GET_LINK_STATUS) + dev_err(&dev->udev->dev, "send command %#x: error %d\n", + cmd, ret); goto end; } @@ -90,8 +90,10 @@ static int cx82310_cmd(struct usbnet *dev, enum cx82310_cmd cmd, bool reply, buf, CMD_PACKET_SIZE, &actual_len, CMD_TIMEOUT); if (ret < 0) { - dev_err(&dev->udev->dev, - "reply receive error %d\n", ret); + if (cmd != CMD_GET_LINK_STATUS) + dev_err(&dev->udev->dev, + "reply receive error %d\n", + ret); goto end; } if (actual_len > 0) @@ -134,6 +136,8 @@ static int cx82310_bind(struct usbnet *dev, struct usb_interface *intf) int ret; char buf[15]; struct usb_device *udev = dev->udev; + u8 link[3]; + int timeout = 50; /* avoid ADSL modems - continue only if iProduct is "USB NET CARD" */ if (usb_string(udev, udev->descriptor.iProduct, buf, sizeof(buf)) > 0 @@ -160,6 +164,20 @@ static int cx82310_bind(struct usbnet *dev, struct usb_interface *intf) if (!dev->partial_data) return -ENOMEM; + /* wait for firmware to become ready (indicated by the link being up) */ + while (--timeout) { + ret = cx82310_cmd(dev, CMD_GET_LINK_STATUS, true, NULL, 0, + link, sizeof(link)); + /* the command can time out during boot - it's not an error */ + if (!ret && link[0] == 1 && link[2] == 1) + break; + msleep(500); + }; + if (!timeout) { + dev_err(&udev->dev, "firmware not ready in time\n"); + return -ETIMEDOUT; + } + /* enable ethernet mode (?) */ ret = cx82310_cmd(dev, CMD_ETHERNET_MODE, true, "\x01", 1, NULL, 0); if (ret) { -- cgit v1.2.3