From cda4ee3f2e6907e89baf7a12e02e02fa208c0625 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Fri, 14 Oct 2011 12:54:47 -0700 Subject: iwlagn: fix the race in the unmapping of the HCMD As Stanislaw pointed out, my patch iwlagn: fix a race in the unmapping of the TFDs solved only part of the problem. The race still exists for TFDs of the host commands. Fix that too. Reported-by: Stanislaw Gruszka Signed-off-by: Emmanuel Grumbach Signed-off-by: Wey-Yi Guy Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-trans-pcie.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c b/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c index 8e8c75c997ee..da3411057afc 100644 --- a/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c +++ b/drivers/net/wireless/iwlwifi/iwl-trans-pcie.c @@ -407,6 +407,7 @@ static void iwl_tx_queue_unmap(struct iwl_trans *trans, int txq_id) struct iwl_queue *q = &txq->q; enum dma_data_direction dma_dir; unsigned long flags; + spinlock_t *lock; if (!q->n_bd) return; @@ -414,19 +415,22 @@ static void iwl_tx_queue_unmap(struct iwl_trans *trans, int txq_id) /* In the command queue, all the TBs are mapped as BIDI * so unmap them as such. */ - if (txq_id == trans->shrd->cmd_queue) + if (txq_id == trans->shrd->cmd_queue) { dma_dir = DMA_BIDIRECTIONAL; - else + lock = &trans->hcmd_lock; + } else { dma_dir = DMA_TO_DEVICE; + lock = &trans->shrd->sta_lock; + } - spin_lock_irqsave(&trans->shrd->sta_lock, flags); + spin_lock_irqsave(lock, flags); while (q->write_ptr != q->read_ptr) { /* The read_ptr needs to bound by q->n_window */ iwlagn_txq_free_tfd(trans, txq, get_cmd_index(q, q->read_ptr), dma_dir); q->read_ptr = iwl_queue_inc_wrap(q->read_ptr, q->n_bd); } - spin_unlock_irqrestore(&trans->shrd->sta_lock, flags); + spin_unlock_irqrestore(lock, flags); } /** -- cgit v1.2.3 From 52d6d4ef5e6d1517688e27c11c01ab303ec681dd Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Thu, 20 Oct 2011 14:22:43 +0530 Subject: ath9k_hw: Fix regression of register offset for AR9003 chips My recent commits (3782c69d, 324c74a) introduced regression for register offset selection that based on the macversion. Not using parentheses in proper manner for ternary operator leads to select wrong offset for the registers. This issue was observed with AR9462 chip that immediate disconnect after the association with the following message ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47 after 500ms, disconnecting. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ar9003_phy.h | 24 ++++++++++++------------ 1 file changed, 12 insertions(+), 12 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h index 2f4023e66081..70e01031714f 100644 --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h @@ -572,14 +572,14 @@ #define AR_PHY_TXGAIN_TABLE (AR_SM_BASE + 0x300) -#define AR_PHY_TX_IQCAL_CONTROL_0 (AR_SM_BASE + AR_SREV_9485(ah) ? \ - 0x3c4 : 0x444) -#define AR_PHY_TX_IQCAL_CONTROL_1 (AR_SM_BASE + AR_SREV_9485(ah) ? \ - 0x3c8 : 0x448) -#define AR_PHY_TX_IQCAL_START (AR_SM_BASE + AR_SREV_9485(ah) ? \ - 0x3c4 : 0x440) -#define AR_PHY_TX_IQCAL_STATUS_B0 (AR_SM_BASE + AR_SREV_9485(ah) ? \ - 0x3f0 : 0x48c) +#define AR_PHY_TX_IQCAL_CONTROL_0 (AR_SM_BASE + (AR_SREV_9485(ah) ? \ + 0x3c4 : 0x444)) +#define AR_PHY_TX_IQCAL_CONTROL_1 (AR_SM_BASE + (AR_SREV_9485(ah) ? \ + 0x3c8 : 0x448)) +#define AR_PHY_TX_IQCAL_START (AR_SM_BASE + (AR_SREV_9485(ah) ? \ + 0x3c4 : 0x440)) +#define AR_PHY_TX_IQCAL_STATUS_B0 (AR_SM_BASE + (AR_SREV_9485(ah) ? \ + 0x3f0 : 0x48c)) #define AR_PHY_TX_IQCAL_CORR_COEFF_B0(_i) (AR_SM_BASE + \ (AR_SREV_9485(ah) ? \ 0x3d0 : 0x450) + ((_i) << 2)) @@ -931,10 +931,10 @@ #define AR_PHY_AIC_SRAM_ADDR_B1 (AR_SM1_BASE + 0x5f0) #define AR_PHY_AIC_SRAM_DATA_B1 (AR_SM1_BASE + 0x5f4) -#define AR_PHY_RTT_TABLE_SW_INTF_B(i) (0x384 + (i) ? \ - AR_SM1_BASE : AR_SM_BASE) -#define AR_PHY_RTT_TABLE_SW_INTF_1_B(i) (0x388 + (i) ? \ - AR_SM1_BASE : AR_SM_BASE) +#define AR_PHY_RTT_TABLE_SW_INTF_B(i) (0x384 + ((i) ? \ + AR_SM1_BASE : AR_SM_BASE)) +#define AR_PHY_RTT_TABLE_SW_INTF_1_B(i) (0x388 + ((i) ? \ + AR_SM1_BASE : AR_SM_BASE)) /* * Channel 2 Register Map */ -- cgit v1.2.3 From 91ae4d02913808fc4056168766185d1a3bd63f65 Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Thu, 20 Oct 2011 14:29:38 +0530 Subject: ath9k_hw: Fix radio retention for AR9462 IQ calibration during fast channel change sometimes failed with RTT. And also restoring invalid radio retention readings during init cal could cause failure to set the channel properly. This patch counts the valid rtt history readings and clears rtt mask. Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ar9003_calib.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c index 16851cb109a6..a4cd1617092b 100644 --- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c +++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c @@ -908,12 +908,15 @@ static bool ar9003_hw_rtt_restore(struct ath_hw *ah, struct ath9k_channel *chan) int i; bool restore; - if (!(ah->caps.hw_caps & ATH9K_HW_CAP_RTT) || !ah->caldata) + if (!ah->caldata) return false; hist = &ah->caldata->rtt_hist; + if (!hist->num_readings) + return false; + ar9003_hw_rtt_enable(ah); - ar9003_hw_rtt_set_mask(ah, 0x10); + ar9003_hw_rtt_set_mask(ah, 0x00); for (i = 0; i < AR9300_MAX_CHAINS; i++) { if (!(ah->rxchainmask & (1 << i))) continue; @@ -1070,6 +1073,7 @@ skip_tx_iqcal: if (is_reusable && (hist->num_readings < RTT_HIST_MAX)) { u32 *table; + hist->num_readings++; for (i = 0; i < AR9300_MAX_CHAINS; i++) { if (!(ah->rxchainmask & (1 << i))) continue; -- cgit v1.2.3 From fd26981cf53ee91951a92fae53416e4ce639164c Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Fri, 21 Oct 2011 12:53:51 +0530 Subject: ath9k_hw: Fix regression of register offset of AR9330/AR9340 The commit ce407afc10 introduced regression for AR9330/AR9340 register offsets. Some of the register offsets are common for AR9330/AR9340/AR9485 except AR9380. Fix that. Cc: stable@kernel.org [3.1.0+] Cc: Senthil Balasubramanian Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ar9003_phy.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h index 70e01031714f..4114fe752c6b 100644 --- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h +++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h @@ -651,7 +651,7 @@ #define AR_SWITCH_TABLE_ALL_S (0) #define AR_PHY_65NM_CH0_THERM (AR_SREV_9300(ah) ? 0x16290 :\ - (AR_SREV_9485(ah) ? 0x1628c : 0x16294)) + (AR_SREV_9462(ah) ? 0x16294 : 0x1628c)) #define AR_PHY_65NM_CH0_THERM_LOCAL 0x80000000 #define AR_PHY_65NM_CH0_THERM_LOCAL_S 31 @@ -668,12 +668,12 @@ #define AR_PHY_65NM_CH2_RXTX2 0x16904 #define AR_CH0_TOP2 (AR_SREV_9300(ah) ? 0x1628c : \ - (AR_SREV_9485(ah) ? 0x16284 : 0x16290)) + (AR_SREV_9462(ah) ? 0x16290 : 0x16284)) #define AR_CH0_TOP2_XPABIASLVL 0xf000 #define AR_CH0_TOP2_XPABIASLVL_S 12 #define AR_CH0_XTAL (AR_SREV_9300(ah) ? 0x16294 : \ - (AR_SREV_9485(ah) ? 0x16290 : 0x16298)) + (AR_SREV_9462(ah) ? 0x16298 : 0x16290)) #define AR_CH0_XTAL_CAPINDAC 0x7f000000 #define AR_CH0_XTAL_CAPINDAC_S 24 #define AR_CH0_XTAL_CAPOUTDAC 0x00fe0000 @@ -908,8 +908,8 @@ #define AR_PHY_TPC_5_B1 (AR_SM1_BASE + 0x208) #define AR_PHY_TPC_6_B1 (AR_SM1_BASE + 0x20c) #define AR_PHY_TPC_11_B1 (AR_SM1_BASE + 0x220) -#define AR_PHY_PDADC_TAB_1 (AR_SM1_BASE + (AR_SREV_AR9300(ah) ? \ - 0x240 : 0x280)) +#define AR_PHY_PDADC_TAB_1 (AR_SM1_BASE + (AR_SREV_AR9462(ah) ? \ + 0x280 : 0x240)) #define AR_PHY_TPC_19_B1 (AR_SM1_BASE + 0x240) #define AR_PHY_TPC_19_B1_ALPHA_THERM 0xff #define AR_PHY_TPC_19_B1_ALPHA_THERM_S 0 -- cgit v1.2.3 From 94d55d62bd757611f07a9122e5e07ce929b8d38d Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Fri, 21 Oct 2011 18:38:56 +0200 Subject: carl9170: fix AMPDU TX_CTL_REQ_TX_STATUS handling Previously the driver did not care if TX_CTL_REQ_TX_STATUS was set on aggregated frames or not and it would silently drop successfully sent frames if possible [much like: "no news is good news!"]. But, TX_CTL_REQ_TX_STATUS was invented for a reason and no tx status report should ever be dropped if it is set. Reported-by: Johannes Berg Signed-off-by: Christian Lamparter Signed-off-by: John W. Linville --- drivers/net/wireless/ath/carl9170/tx.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/carl9170/tx.c b/drivers/net/wireless/ath/carl9170/tx.c index d20946939cd8..59472e1605cd 100644 --- a/drivers/net/wireless/ath/carl9170/tx.c +++ b/drivers/net/wireless/ath/carl9170/tx.c @@ -296,7 +296,8 @@ static void carl9170_tx_release(struct kref *ref) super = (void *)skb->data; txinfo->status.ampdu_len = super->s.rix; txinfo->status.ampdu_ack_len = super->s.cnt; - } else if (txinfo->flags & IEEE80211_TX_STAT_ACK) { + } else if ((txinfo->flags & IEEE80211_TX_STAT_ACK) && + !(txinfo->flags & IEEE80211_TX_CTL_REQ_TX_STATUS)) { /* * drop redundant tx_status reports: * @@ -308,15 +309,17 @@ static void carl9170_tx_release(struct kref *ref) * * 3. minstrel_ht is picky, it only accepts * reports of frames with the TX_STATUS_AMPDU flag. + * + * 4. mac80211 is not particularly interested in + * feedback either [CTL_REQ_TX_STATUS not set] */ dev_kfree_skb_any(skb); return; } else { /* - * Frame has failed, but we want to keep it in - * case it was lost due to a power-state - * transition. + * Either the frame transmission has failed or + * mac80211 requested tx status. */ } } -- cgit v1.2.3 From 98fb2cc115b4ef1ea0a2d87a170c183bd395dd6c Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Mon, 24 Oct 2011 18:13:40 +0530 Subject: ath9k_hw: Update AR9485 initvals to fix system hang issue This patch fixes system hang when resuming from S3 state and lower rate sens failure issue. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ar9485_initvals.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/ar9485_initvals.h b/drivers/net/wireless/ath/ath9k/ar9485_initvals.h index 611ea6ce8508..d16d029f81a9 100644 --- a/drivers/net/wireless/ath/ath9k/ar9485_initvals.h +++ b/drivers/net/wireless/ath/ath9k/ar9485_initvals.h @@ -521,7 +521,7 @@ static const u32 ar9485_1_1_radio_postamble[][2] = { {0x000160ac, 0x24611800}, {0x000160b0, 0x03284f3e}, {0x0001610c, 0x00170000}, - {0x00016140, 0x10804008}, + {0x00016140, 0x50804008}, }; static const u32 ar9485_1_1_mac_postamble[][5] = { @@ -603,7 +603,7 @@ static const u32 ar9485_1_1_radio_core[][2] = { static const u32 ar9485_1_1_pcie_phy_pll_on_clkreq_enable_L1[][2] = { /* Addr allmodes */ - {0x00018c00, 0x10052e5e}, + {0x00018c00, 0x18052e5e}, {0x00018c04, 0x000801d8}, {0x00018c08, 0x0000080c}, }; @@ -776,7 +776,7 @@ static const u32 ar9485_modes_green_ob_db_tx_gain_1_1[][5] = { static const u32 ar9485_1_1_pcie_phy_clkreq_disable_L1[][2] = { /* Addr allmodes */ - {0x00018c00, 0x10013e5e}, + {0x00018c00, 0x18013e5e}, {0x00018c04, 0x000801d8}, {0x00018c08, 0x0000080c}, }; @@ -882,7 +882,7 @@ static const u32 ar9485_fast_clock_1_1_baseband_postamble[][3] = { static const u32 ar9485_1_1_pcie_phy_pll_on_clkreq_disable_L1[][2] = { /* Addr allmodes */ - {0x00018c00, 0x10012e5e}, + {0x00018c00, 0x18012e5e}, {0x00018c04, 0x000801d8}, {0x00018c08, 0x0000080c}, }; @@ -1021,7 +1021,7 @@ static const u32 ar9485_common_rx_gain_1_1[][2] = { static const u32 ar9485_1_1_pcie_phy_clkreq_enable_L1[][2] = { /* Addr allmodes */ - {0x00018c00, 0x10053e5e}, + {0x00018c00, 0x18053e5e}, {0x00018c04, 0x000801d8}, {0x00018c08, 0x0000080c}, }; -- cgit v1.2.3 From 93348928f2c980718434b1bc42f9d7638d665db4 Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Tue, 25 Oct 2011 16:47:36 +0530 Subject: ath9k_hw: Fix noise floor calibration timeout on fast channel change During the fast channel change noise floor values are being loaded twice at init_cal and after channel_change. The commit "ath9k_hw: Improve fast channel change for AR9003 chips" overlooked it that caused failure to load nf while doing bgscan. This patch performs noise floor calibration after the fast and full reset. Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ar9002_calib.c | 4 ---- drivers/net/wireless/ath/ath9k/ar9003_calib.c | 3 --- drivers/net/wireless/ath/ath9k/hw.c | 3 +++ 3 files changed, 3 insertions(+), 7 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/ar9002_calib.c b/drivers/net/wireless/ath/ath9k/ar9002_calib.c index e0ab0657cc3a..88279e325dca 100644 --- a/drivers/net/wireless/ath/ath9k/ar9002_calib.c +++ b/drivers/net/wireless/ath/ath9k/ar9002_calib.c @@ -868,10 +868,6 @@ static bool ar9002_hw_init_cal(struct ath_hw *ah, struct ath9k_channel *chan) /* Do PA Calibration */ ar9002_hw_pa_cal(ah, true); - /* Do NF Calibration after DC offset and other calibrations */ - ath9k_hw_loadnf(ah, chan); - ath9k_hw_start_nfcal(ah, true); - if (ah->caldata) ah->caldata->nfcal_pending = true; diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c index a4cd1617092b..12a730dcb500 100644 --- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c +++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c @@ -1085,9 +1085,6 @@ skip_tx_iqcal: ar9003_hw_rtt_disable(ah); } - ath9k_hw_loadnf(ah, chan); - ath9k_hw_start_nfcal(ah, true); - /* Initialize list pointers */ ah->cal_list = ah->cal_list_last = ah->cal_list_curr = NULL; ah->supp_cals = IQ_MISMATCH_CAL; diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c index f16d2033081f..b479160dc262 100644 --- a/drivers/net/wireless/ath/ath9k/hw.c +++ b/drivers/net/wireless/ath/ath9k/hw.c @@ -1724,6 +1724,9 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, if (!ath9k_hw_init_cal(ah, chan)) return -EIO; + ath9k_hw_loadnf(ah, chan); + ath9k_hw_start_nfcal(ah, true); + ENABLE_REGWRITE_BUFFER(ah); ath9k_hw_restore_chainmask(ah); -- cgit v1.2.3 From 3209e061ad04465b3999091f315049c95ac6cbcb Mon Sep 17 00:00:00 2001 From: Andres Salomon Date: Wed, 26 Oct 2011 10:19:26 -0700 Subject: libertas: ensure we clean up a scan request properly Commit 2e30168b ("libertas: terminate scan when stopping interface") adds cleanup code to lbs_eth_stop to call cfg80211_scan_done if there's an outstanding cfg80211_scan_request. However, it assumes that the scan request was allocated via the cfg80211 stack. Libertas has its own internal allocation method, kept track of with priv->internal_scan. This doesn't set scan_req->wiphy, amongst other things, which results in hitting a BUG() when we call cfg80211_scan_done on the request. This provides a function to take care of the low-level scan_req cleanup details. We simply call that to deal with finishing up scan requests. The bug we were hitting was: [ 964.321495] kernel BUG at net/wireless/core.h:87! [ 964.329970] Unable to handle kernel NULL pointer dereference at virtual address 00000000 [ 964.341963] pgd = dcf80000 ... [ 964.849998] 9fe0: 00000000 beb417b8 4018e280 401e822c 60000010 00000004 00000000 00000000 [ 964.865007] [] (__bug+0x1c/0x28) from [] (cfg80211_scan_done+0x54/0x6c) [ 964.895324] [] (cfg80211_scan_done+0x54/0x6c) from [] (lbs_eth_stop+0x10c/0x188 [libertas]) [ 964.895324] [] (lbs_eth_stop+0x10c/0x188 [libertas]) from [] (__dev_close_many+0x94/0xc4) [ 964.918995] [] (__dev_close_many+0x94/0xc4) from [] (dev_close_many+0x78/0xe0) Signed-off-by: Andres Salomon Acked-by: Dan Williams Signed-off-by: John W. Linville --- drivers/net/wireless/libertas/cfg.c | 25 +++++++++++++++++-------- drivers/net/wireless/libertas/cfg.h | 1 + drivers/net/wireless/libertas/main.c | 6 ++---- 3 files changed, 20 insertions(+), 12 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/libertas/cfg.c b/drivers/net/wireless/libertas/cfg.c index ff6378276ff0..4fcd653bddc4 100644 --- a/drivers/net/wireless/libertas/cfg.c +++ b/drivers/net/wireless/libertas/cfg.c @@ -728,15 +728,9 @@ static void lbs_scan_worker(struct work_struct *work) le16_to_cpu(scan_cmd->hdr.size), lbs_ret_scan, 0); - if (priv->scan_channel >= priv->scan_req->n_channels) { + if (priv->scan_channel >= priv->scan_req->n_channels) /* Mark scan done */ - if (priv->internal_scan) - kfree(priv->scan_req); - else - cfg80211_scan_done(priv->scan_req, false); - - priv->scan_req = NULL; - } + lbs_scan_done(priv); /* Restart network */ if (carrier) @@ -774,6 +768,21 @@ static void _internal_start_scan(struct lbs_private *priv, bool internal, lbs_deb_leave(LBS_DEB_CFG80211); } +/* + * Clean up priv->scan_req. Should be used to handle the allocation details. + */ +void lbs_scan_done(struct lbs_private *priv) +{ + WARN_ON(!priv->scan_req); + + if (priv->internal_scan) + kfree(priv->scan_req); + else + cfg80211_scan_done(priv->scan_req, false); + + priv->scan_req = NULL; +} + static int lbs_cfg_scan(struct wiphy *wiphy, struct net_device *dev, struct cfg80211_scan_request *request) diff --git a/drivers/net/wireless/libertas/cfg.h b/drivers/net/wireless/libertas/cfg.h index a02ee151710e..558168ce634d 100644 --- a/drivers/net/wireless/libertas/cfg.h +++ b/drivers/net/wireless/libertas/cfg.h @@ -16,6 +16,7 @@ int lbs_reg_notifier(struct wiphy *wiphy, void lbs_send_disconnect_notification(struct lbs_private *priv); void lbs_send_mic_failureevent(struct lbs_private *priv, u32 event); +void lbs_scan_done(struct lbs_private *priv); void lbs_scan_deinit(struct lbs_private *priv); int lbs_disconnect(struct lbs_private *priv, u16 reason); diff --git a/drivers/net/wireless/libertas/main.c b/drivers/net/wireless/libertas/main.c index b03779bcd547..39a6a7a40244 100644 --- a/drivers/net/wireless/libertas/main.c +++ b/drivers/net/wireless/libertas/main.c @@ -255,10 +255,8 @@ static int lbs_eth_stop(struct net_device *dev) lbs_update_mcast(priv); cancel_delayed_work_sync(&priv->scan_work); - if (priv->scan_req) { - cfg80211_scan_done(priv->scan_req, false); - priv->scan_req = NULL; - } + if (priv->scan_req) + lbs_scan_done(priv); netif_carrier_off(priv->dev); -- cgit v1.2.3 From 8a39ef8ba0fa0410d71db8e981e887fe4fdeca88 Mon Sep 17 00:00:00 2001 From: Wey-Yi Guy Date: Thu, 27 Oct 2011 17:19:39 -0700 Subject: iwlwifi: allow pci_enable_msi fail Continue the init process even fail to enable msi out_iounmap is no longer used, remove it Reported-by: werner Tested-by: werner Signed-off-by: Wey-Yi Guy Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-pci.c | 8 +++----- 1 file changed, 3 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/iwl-pci.c b/drivers/net/wireless/iwlwifi/iwl-pci.c index 3b6cc66365e5..19cc6a81da57 100644 --- a/drivers/net/wireless/iwlwifi/iwl-pci.c +++ b/drivers/net/wireless/iwlwifi/iwl-pci.c @@ -445,10 +445,9 @@ static int iwl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) pci_write_config_byte(pdev, PCI_CFG_RETRY_TIMEOUT, 0x00); err = pci_enable_msi(pdev); - if (err) { - dev_printk(KERN_ERR, &pdev->dev, "pci_enable_msi failed"); - goto out_iounmap; - } + if (err) + dev_printk(KERN_ERR, &pdev->dev, + "pci_enable_msi failed(0X%x)", err); /* TODO: Move this away, not needed if not MSI */ /* enable rfkill interrupt: hw bug w/a */ @@ -469,7 +468,6 @@ static int iwl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent) out_disable_msi: pci_disable_msi(pdev); -out_iounmap: pci_iounmap(pdev, pci_bus->hw_base); out_pci_release_regions: pci_set_drvdata(pdev, NULL); -- cgit v1.2.3 From addc98519207fb8ca0609da720469e415f784d0c Mon Sep 17 00:00:00 2001 From: Larry Finger Date: Fri, 28 Oct 2011 12:17:49 -0500 Subject: b43: Remove unneeded message The driver can spam the logs with "RX: Packet dropped" messages. These drops originate from 1. a correpted PLCP, 2. decryption errors, and 3. packet size underruns. Condition #3 logs a separate message, thus no dropped message is needed. Signed-off-by: Larry Finger Signed-off-by: John W. Linville --- drivers/net/wireless/b43/xmit.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/xmit.c b/drivers/net/wireless/b43/xmit.c index c73e8600d218..58ea0e5fabfd 100644 --- a/drivers/net/wireless/b43/xmit.c +++ b/drivers/net/wireless/b43/xmit.c @@ -827,7 +827,6 @@ void b43_rx(struct b43_wldev *dev, struct sk_buff *skb, const void *_rxhdr) #endif return; drop: - b43dbg(dev->wl, "RX: Packet dropped\n"); dev_kfree_skb_any(skb); } -- cgit v1.2.3 From f956c34e2a665a1c457d0af7db7604b22f5acb19 Mon Sep 17 00:00:00 2001 From: Wey-Yi Guy Date: Sat, 29 Oct 2011 23:15:15 -0700 Subject: iwlwifi: don't perform "echo test" when cmd queue stuck Perform "echo test" when cmd queue stuck detected, somethime it will cause calltrace. I am not sure how to fix it yet, just remove the action now until find a better way to handle it. Reported-by: Reinette Chatre Signed-off-by: Wey-Yi Guy Signed-off-by: John W. Linville --- drivers/net/wireless/iwlwifi/iwl-core.c | 10 ---------- 1 file changed, 10 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c index b247a56d5135..001fdf140abb 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.c +++ b/drivers/net/wireless/iwlwifi/iwl-core.c @@ -1755,16 +1755,6 @@ static inline int iwl_check_stuck_queue(struct iwl_priv *priv, int txq) { if (iwl_trans_check_stuck_queue(trans(priv), txq)) { int ret; - if (txq == priv->shrd->cmd_queue) { - /* - * validate command queue still working - * by sending "ECHO" command - */ - if (!iwl_cmd_echo_test(priv)) - return 0; - else - IWL_DEBUG_HC(priv, "echo testing fail\n"); - } ret = iwl_force_reset(priv, IWL_FW_RESET, false); return (ret == -EAGAIN) ? 0 : 1; } -- cgit v1.2.3