| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.
The patchset implements the support in kernel by searching the device
tree under the root port.
Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
We should not assign 64bit ranges to PCI devices that only take 32bit
prefetchable addresses.
Try to set IORESOURCE_MEM_64 in 64bit resource of pci_device/pci_bridge
and make the bus resource only have that bit set when all devices under
it support 64bit prefetchable memory. Use that flag to allocate
resources from that range.
Reported-by: Yannick <yannick.roehlly@free.fr>
Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
In preparation for PCI core hotplug, we need to ensure that we do
not attempt to re-enable bridges that have already been enabled.
Reported-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
drivers/pci/hotplug/fakephp.c:283: warning: passing argument 1 of 'pci_bus_add_devices' discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch splits a new function, pci_bus_add_child(), from
pci_bus_add_devices(). The new function can be used to register PCI
buses to the device core.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Cleanup pci_bus_add_devices() by negating the conditional and
continuing, rather than having a single conditional take up the whole
body.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Currently, only PHBs get the legacy_* files, which makes it tricky for
userland to get access to the legacy space. This commit exposes them in
every bus, since even child buses may forward legacy cycles if
configured properly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Stephen Hemminger wrote:
> Looks like Mike created cpulistaffinty in sysfs but never completed
> the job.
This patch hooks things up correctly, taking care to remove the new file
when the bus is destroyed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This patch finally removes the global list of PCI devices. We are
relying entirely on the list held in the driver core now, and do not
need a separate "shadow" list as no one uses it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists. The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
PCI busses can be registered multiple times, so we need to detect if we
have registered our bus structure in sysfs already. If so, don't do it
again.
Thanks to Guennadi Liakhovetski <g.liakhovetski@gmx.de> for reporting
the problem, and to Linus for poking me to get me to believe that it was
a real problem.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Due to the class_device cleanup of pci_bus, the error messages when
things go wrong are incorrect. So fix this up to properly report what
is really happening, if things go wrong.
Thanks to Kay for pointing out the issue.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.
Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it. If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch removes the following unused exports:
- remove the following unused EXPORT_SYMBOL's:
- pci-acpi.c: pci_osc_support_set
- proc.c: pci_proc_detach_bus
- remove the following unused EXPORT_SYMBOL_GPL's:
- bus.c: pci_walk_bus
- probe.c: pci_create_bus
- setup-res.c: pci_claim_resource
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Functions marked __devinit will be removed after kernel init. But being
exported they are potentially called by a module much later.
So the safer choice seems to be to keep the function even in the non
CONFIG_HOTPLUG case.
This silence the follwoing section mismatch warnings:
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_device from __ksymtab_gpl between '__ksymtab_pci_bus_add_device' (at offset 0x20) and '__ksymtab_pci_walk_bus'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_create_bus from __ksymtab_gpl between '__ksymtab_pci_create_bus' (at offset 0x40) and '__ksymtab_pci_stop_bus_device'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_max_busnr from __ksymtab_gpl between '__ksymtab_pci_bus_max_busnr' (at offset 0xc0) and '__ksymtab_pci_assign_resource_fixed'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_claim_resource from __ksymtab_gpl between '__ksymtab_pci_claim_resource' (at offset 0xe0) and '__ksymtab_pcie_port_bus_type'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_devices from __ksymtab between '__ksymtab_pci_bus_add_devices' (at offset 0x70) and '__ksymtab_pci_bus_alloc_resource'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_scan_bus_parented from __ksymtab between '__ksymtab_pci_scan_bus_parented' (at offset 0x90) and '__ksymtab_pci_root_buses'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_assign_resources from __ksymtab between '__ksymtab_pci_bus_assign_resources' (at offset 0x4d0) and '__ksymtab_pci_bus_size_bridges'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_size_bridges from __ksymtab between '__ksymtab_pci_bus_size_bridges' (at offset 0x4e0) and '__ksymtab_pci_setup_cardbus'
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
pci_walk_bus has a race with pci_destroy_dev. When cb is called
in pci_walk_bus, pci_destroy_dev might unlink the dev pointed by next.
Later on in the next loop, pointer next becomes NULL and cause
kernel panic.
Below patch against 2.6.17-rc4 fixes it by changing pci_bus_lock (spin_lock)
to pci_bus_sem (rw_semaphore).
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The PCI error recovery infrastructure needs to be able to contact all
the drivers affected by a PCI error event, which may mean traversing
all the devices under a given PCI-PCI bridge. This patch adds a
function to the PCI core that traverses all the PCI devices on a PCI
bus and under any PCI-PCI bridges on that bus (and so on), calling a
given function for each device. This provides a way for the error
recovery code to iterate through all devices that are affected by an
error event.
This version is not implemented as a recursive function. Instead,
when we reach a PCI-PCI bridge, we set the pointers to start doing the
devices on the bus under the bridge, and when we reach the end of a
bus's devices, we use the bus->self pointer to go back up to the next
higher bus and continue doing its devices.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The reason we have PCIBIOS_MIN_IO and PCIBIOS_MIN_CARDBUS_IO is because
we want to protect badly documented motherboard PCI resources and thus
don't want to allocate new resources in low IO/MEM space.
However, if we have already discovered a PCI bridge with a specified
resource base, that should override that decision.
This change will allow us to move the "careful" region upwards without
resulting in problems allocating resources in low mappings. This was
brought on by us having allocated a bus resource at 0x1000, conflicting
with a undocumented VAIO Sony PI resources.
|
|
on creation
When a pci child bus is created, add it to the parent's children list
immediately rather than waiting till pci_bus_add_devices(). For hot-plug
bridges/devices, pci_bus_add_devices() may be called much later, after they
have been properly configured. In the meantime, this allows us to use the
normal pci bus search functions for the hot-plug bridges/buses.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
|
