blob: bec48ca89bbadd80500cfcfbceaa8547bcd1d30f (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
|
/*
* include/asm-arm/arch-at91rm9200/at91_spi.h
*
* Copyright (C) 2005 Ivan Kokshaysky
* Copyright (C) SAN People
*
* Serial Peripheral Interface (SPI) registers.
* Based on AT91RM9200 datasheet revision E.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef AT91_SPI_H
#define AT91_SPI_H
#define AT91_SPI_CR 0x00 /* Control Register */
#define AT91_SPI_SPIEN (1 << 0) /* SPI Enable */
#define AT91_SPI_SPIDIS (1 << 1) /* SPI Disable */
#define AT91_SPI_SWRST (1 << 7) /* SPI Software Reset */
#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */
#define AT91_SPI_MR 0x04 /* Mode Register */
#define AT91_SPI_MSTR (1 << 0) /* Master/Slave Mode */
#define AT91_SPI_PS (1 << 1) /* Peripheral Select */
#define AT91_SPI_PS_FIXED (0 << 1)
#define AT91_SPI_PS_VARIABLE (1 << 1)
#define AT91_SPI_PCSDEC (1 << 2) /* Chip Select Decode */
#define AT91_SPI_DIV32 (1 << 3) /* Clock Selection [AT91RM9200 only] */
#define AT91_SPI_MODFDIS (1 << 4) /* Mode Fault Detection */
#define AT91_SPI_LLB (1 << 7) /* Local Loopback Enable */
#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */
#define AT91_SPI_DLYBCS (0xff << 24) /* Delay Between Chip Selects */
#define AT91_SPI_RDR 0x08 /* Receive Data Register */
#define AT91_SPI_RD (0xffff << 0) /* Receive Data */
#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */
#define AT91_SPI_TDR 0x0c /* Transmit Data Register */
#define AT91_SPI_TD (0xffff << 0) /* Transmit Data */
#define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */
#define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */
#define AT91_SPI_SR 0x10 /* Status Register */
#define AT91_SPI_RDRF (1 << 0) /* Receive Data Register Full */
#define AT91_SPI_TDRE (1 << 1) /* Transmit Data Register Full */
#define AT91_SPI_MODF (1 << 2) /* Mode Fault Error */
#define AT91_SPI_OVRES (1 << 3) /* Overrun Error Status */
#define AT91_SPI_ENDRX (1 << 4) /* End of RX buffer */
#define AT91_SPI_ENDTX (1 << 5) /* End of TX buffer */
#define AT91_SPI_RXBUFF (1 << 6) /* RX Buffer Full */
#define AT91_SPI_TXBUFE (1 << 7) /* TX Buffer Empty */
#define AT91_SPI_NSSR (1 << 8) /* NSS Rising [SAM9261 only] */
#define AT91_SPI_TXEMPTY (1 << 9) /* Transmission Register Empty [SAM9261 only] */
#define AT91_SPI_SPIENS (1 << 16) /* SPI Enable Status */
#define AT91_SPI_IER 0x14 /* Interrupt Enable Register */
#define AT91_SPI_IDR 0x18 /* Interrupt Disable Register */
#define AT91_SPI_IMR 0x1c /* Interrupt Mask Register */
#define AT91_SPI_CSR(n) (0x30 + ((n) * 4)) /* Chip Select Registers 0-3 */
#define AT91_SPI_CPOL (1 << 0) /* Clock Polarity */
#define AT91_SPI_NCPHA (1 << 1) /* Clock Phase */
#define AT91_SPI_CSAAT (1 << 3) /* Chip Select Active After Transfer [SAM9261 only] */
#define AT91_SPI_BITS (0xf << 4) /* Bits Per Transfer */
#define AT91_SPI_BITS_8 (0 << 4)
#define AT91_SPI_BITS_9 (1 << 4)
#define AT91_SPI_BITS_10 (2 << 4)
#define AT91_SPI_BITS_11 (3 << 4)
#define AT91_SPI_BITS_12 (4 << 4)
#define AT91_SPI_BITS_13 (5 << 4)
#define AT91_SPI_BITS_14 (6 << 4)
#define AT91_SPI_BITS_15 (7 << 4)
#define AT91_SPI_BITS_16 (8 << 4)
#define AT91_SPI_SCBR (0xff << 8) /* Serial Clock Baud Rate */
#define AT91_SPI_DLYBS (0xff << 16) /* Delay before SPCK */
#define AT91_SPI_DLYBCT (0xff << 24) /* Delay between Consecutive Transfers */
#endif
|
