diff options
Diffstat (limited to 'arch/mips/include/asm/mach-au1x00')
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/au1000.h | 876 | ||||
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/au1100_mmc.h | 2 | ||||
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h | 24 | ||||
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/au1xxx_eth.h | 17 | ||||
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/gpio-au1000.h | 164 | ||||
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/gpio.h | 2 | ||||
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/ioremap.h | 2 | ||||
-rw-r--r-- | arch/mips/include/asm/mach-au1x00/prom.h | 1 |
8 files changed, 486 insertions, 602 deletions
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h index 854e95f1b07c..ae07423e6e82 100644 --- a/arch/mips/include/asm/mach-au1x00/au1000.h +++ b/arch/mips/include/asm/mach-au1x00/au1000.h @@ -130,6 +130,56 @@ static inline int au1xxx_cpu_needs_config_od(void) return 0; } +#define ALCHEMY_CPU_UNKNOWN -1 +#define ALCHEMY_CPU_AU1000 0 +#define ALCHEMY_CPU_AU1500 1 +#define ALCHEMY_CPU_AU1100 2 +#define ALCHEMY_CPU_AU1550 3 +#define ALCHEMY_CPU_AU1200 4 + +static inline int alchemy_get_cputype(void) +{ + switch (read_c0_prid() & 0xffff0000) { + case 0x00030000: + return ALCHEMY_CPU_AU1000; + break; + case 0x01030000: + return ALCHEMY_CPU_AU1500; + break; + case 0x02030000: + return ALCHEMY_CPU_AU1100; + break; + case 0x03030000: + return ALCHEMY_CPU_AU1550; + break; + case 0x04030000: + case 0x05030000: + return ALCHEMY_CPU_AU1200; + break; + } + + return ALCHEMY_CPU_UNKNOWN; +} + +static inline void alchemy_uart_putchar(u32 uart_phys, u8 c) +{ + void __iomem *base = (void __iomem *)KSEG1ADDR(uart_phys); + int timeout, i; + + /* check LSR TX_EMPTY bit */ + timeout = 0xffffff; + do { + if (__raw_readl(base + 0x1c) & 0x20) + break; + /* slow down */ + for (i = 10000; i; i--) + asm volatile ("nop"); + } while (--timeout); + + __raw_writel(c, base + 0x04); /* tx */ + wmb(); +} + /* arch/mips/au1000/common/clocks.c */ extern void set_au1x00_speed(unsigned int new_freq); extern unsigned int get_au1x00_speed(void); @@ -143,20 +193,332 @@ void au_sleep(void); void save_au1xxx_intctl(void); void restore_au1xxx_intctl(void); -/* - * Every board describes its IRQ mapping with this table. - */ -struct au1xxx_irqmap { - int im_irq; - int im_type; - int im_request; + +/* SOC Interrupt numbers */ + +#define AU1000_INTC0_INT_BASE (MIPS_CPU_IRQ_BASE + 8) +#define AU1000_INTC0_INT_LAST (AU1000_INTC0_INT_BASE + 31) +#define AU1000_INTC1_INT_BASE (AU1000_INTC0_INT_LAST + 1) +#define AU1000_INTC1_INT_LAST (AU1000_INTC1_INT_BASE + 31) +#define AU1000_MAX_INTR AU1000_INTC1_INT_LAST + +enum soc_au1000_ints { + AU1000_FIRST_INT = AU1000_INTC0_INT_BASE, + AU1000_UART0_INT = AU1000_FIRST_INT, + AU1000_UART1_INT, + AU1000_UART2_INT, + AU1000_UART3_INT, + AU1000_SSI0_INT, + AU1000_SSI1_INT, + AU1000_DMA_INT_BASE, + + AU1000_TOY_INT = AU1000_FIRST_INT + 14, + AU1000_TOY_MATCH0_INT, + AU1000_TOY_MATCH1_INT, + AU1000_TOY_MATCH2_INT, + AU1000_RTC_INT, + AU1000_RTC_MATCH0_INT, + AU1000_RTC_MATCH1_INT, + AU1000_RTC_MATCH2_INT, + AU1000_IRDA_TX_INT, + AU1000_IRDA_RX_INT, + AU1000_USB_DEV_REQ_INT, + AU1000_USB_DEV_SUS_INT, + AU1000_USB_HOST_INT, + AU1000_ACSYNC_INT, + AU1000_MAC0_DMA_INT, + AU1000_MAC1_DMA_INT, + AU1000_I2S_UO_INT, + AU1000_AC97C_INT, + AU1000_GPIO0_INT, + AU1000_GPIO1_INT, + AU1000_GPIO2_INT, + AU1000_GPIO3_INT, + AU1000_GPIO4_INT, + AU1000_GPIO5_INT, + AU1000_GPIO6_INT, + AU1000_GPIO7_INT, + AU1000_GPIO8_INT, + AU1000_GPIO9_INT, + AU1000_GPIO10_INT, + AU1000_GPIO11_INT, + AU1000_GPIO12_INT, + AU1000_GPIO13_INT, + AU1000_GPIO14_INT, + AU1000_GPIO15_INT, + AU1000_GPIO16_INT, + AU1000_GPIO17_INT, + AU1000_GPIO18_INT, + AU1000_GPIO19_INT, + AU1000_GPIO20_INT, + AU1000_GPIO21_INT, + AU1000_GPIO22_INT, + AU1000_GPIO23_INT, + AU1000_GPIO24_INT, + AU1000_GPIO25_INT, + AU1000_GPIO26_INT, + AU1000_GPIO27_INT, + AU1000_GPIO28_INT, + AU1000_GPIO29_INT, + AU1000_GPIO30_INT, + AU1000_GPIO31_INT, }; -/* core calls this function to let boards initialize other IRQ sources */ -void board_init_irq(void); +enum soc_au1100_ints { + AU1100_FIRST_INT = AU1000_INTC0_INT_BASE, + AU1100_UART0_INT = AU1100_FIRST_INT, + AU1100_UART1_INT, + AU1100_SD_INT, + AU1100_UART3_INT, + AU1100_SSI0_INT, + AU1100_SSI1_INT, + AU1100_DMA_INT_BASE, + + AU1100_TOY_INT = AU1100_FIRST_INT + 14, + AU1100_TOY_MATCH0_INT, + AU1100_TOY_MATCH1_INT, + AU1100_TOY_MATCH2_INT, + AU1100_RTC_INT, + AU1100_RTC_MATCH0_INT, + AU1100_RTC_MATCH1_INT, + AU1100_RTC_MATCH2_INT, + AU1100_IRDA_TX_INT, + AU1100_IRDA_RX_INT, + AU1100_USB_DEV_REQ_INT, + AU1100_USB_DEV_SUS_INT, + AU1100_USB_HOST_INT, + AU1100_ACSYNC_INT, + AU1100_MAC0_DMA_INT, + AU1100_GPIO208_215_INT, + AU1100_LCD_INT, + AU1100_AC97C_INT, + AU1100_GPIO0_INT, + AU1100_GPIO1_INT, + AU1100_GPIO2_INT, + AU1100_GPIO3_INT, + AU1100_GPIO4_INT, + AU1100_GPIO5_INT, + AU1100_GPIO6_INT, + AU1100_GPIO7_INT, + AU1100_GPIO8_INT, + AU1100_GPIO9_INT, + AU1100_GPIO10_INT, + AU1100_GPIO11_INT, + AU1100_GPIO12_INT, + AU1100_GPIO13_INT, + AU1100_GPIO14_INT, + AU1100_GPIO15_INT, + AU1100_GPIO16_INT, + AU1100_GPIO17_INT, + AU1100_GPIO18_INT, + AU1100_GPIO19_INT, + AU1100_GPIO20_INT, + AU1100_GPIO21_INT, + AU1100_GPIO22_INT, + AU1100_GPIO23_INT, + AU1100_GPIO24_INT, + AU1100_GPIO25_INT, + AU1100_GPIO26_INT, + AU1100_GPIO27_INT, + AU1100_GPIO28_INT, + AU1100_GPIO29_INT, + AU1100_GPIO30_INT, + AU1100_GPIO31_INT, +}; -/* boards call this to register additional (GPIO) interrupts */ -void au1xxx_setup_irqmap(struct au1xxx_irqmap *map, int count); +enum soc_au1500_ints { + AU1500_FIRST_INT = AU1000_INTC0_INT_BASE, + AU1500_UART0_INT = AU1500_FIRST_INT, + AU1500_PCI_INTA, + AU1500_PCI_INTB, + AU1500_UART3_INT, + AU1500_PCI_INTC, + AU1500_PCI_INTD, + AU1500_DMA_INT_BASE, + + AU1500_TOY_INT = AU1500_FIRST_INT + 14, + AU1500_TOY_MATCH0_INT, + AU1500_TOY_MATCH1_INT, + AU1500_TOY_MATCH2_INT, + AU1500_RTC_INT, + AU1500_RTC_MATCH0_INT, + AU1500_RTC_MATCH1_INT, + AU1500_RTC_MATCH2_INT, + AU1500_PCI_ERR_INT, + AU1500_RESERVED_INT, + AU1500_USB_DEV_REQ_INT, + AU1500_USB_DEV_SUS_INT, + AU1500_USB_HOST_INT, + AU1500_ACSYNC_INT, + AU1500_MAC0_DMA_INT, + AU1500_MAC1_DMA_INT, + AU1500_AC97C_INT = AU1500_FIRST_INT + 31, + AU1500_GPIO0_INT, + AU1500_GPIO1_INT, + AU1500_GPIO2_INT, + AU1500_GPIO3_INT, + AU1500_GPIO4_INT, + AU1500_GPIO5_INT, + AU1500_GPIO6_INT, + AU1500_GPIO7_INT, + AU1500_GPIO8_INT, + AU1500_GPIO9_INT, + AU1500_GPIO10_INT, + AU1500_GPIO11_INT, + AU1500_GPIO12_INT, + AU1500_GPIO13_INT, + AU1500_GPIO14_INT, + AU1500_GPIO15_INT, + AU1500_GPIO200_INT, + AU1500_GPIO201_INT, + AU1500_GPIO202_INT, + AU1500_GPIO203_INT, + AU1500_GPIO20_INT, + AU1500_GPIO204_INT, + AU1500_GPIO205_INT, + AU1500_GPIO23_INT, + AU1500_GPIO24_INT, + AU1500_GPIO25_INT, + AU1500_GPIO26_INT, + AU1500_GPIO27_INT, + AU1500_GPIO28_INT, + AU1500_GPIO206_INT, + AU1500_GPIO207_INT, + AU1500_GPIO208_215_INT, +}; + +enum soc_au1550_ints { + AU1550_FIRST_INT = AU1000_INTC0_INT_BASE, + AU1550_UART0_INT = AU1550_FIRST_INT, + AU1550_PCI_INTA, + AU1550_PCI_INTB, + AU1550_DDMA_INT, + AU1550_CRYPTO_INT, + AU1550_PCI_INTC, + AU1550_PCI_INTD, + AU1550_PCI_RST_INT, + AU1550_UART1_INT, + AU1550_UART3_INT, + AU1550_PSC0_INT, + AU1550_PSC1_INT, + AU1550_PSC2_INT, + AU1550_PSC3_INT, + AU1550_TOY_INT, + AU1550_TOY_MATCH0_INT, + AU1550_TOY_MATCH1_INT, + AU1550_TOY_MATCH2_INT, + AU1550_RTC_INT, + AU1550_RTC_MATCH0_INT, + AU1550_RTC_MATCH1_INT, + AU1550_RTC_MATCH2_INT, + + AU1550_NAND_INT = AU1550_FIRST_INT + 23, + AU1550_USB_DEV_REQ_INT, + AU1550_USB_DEV_SUS_INT, + AU1550_USB_HOST_INT, + AU1550_MAC0_DMA_INT, + AU1550_MAC1_DMA_INT, + AU1550_GPIO0_INT = AU1550_FIRST_INT + 32, + AU1550_GPIO1_INT, + AU1550_GPIO2_INT, + AU1550_GPIO3_INT, + AU1550_GPIO4_INT, + AU1550_GPIO5_INT, + AU1550_GPIO6_INT, + AU1550_GPIO7_INT, + AU1550_GPIO8_INT, + AU1550_GPIO9_INT, + AU1550_GPIO10_INT, + AU1550_GPIO11_INT, + AU1550_GPIO12_INT, + AU1550_GPIO13_INT, + AU1550_GPIO14_INT, + AU1550_GPIO15_INT, + AU1550_GPIO200_INT, + AU1550_GPIO201_205_INT, /* Logical or of GPIO201:205 */ + AU1550_GPIO16_INT, + AU1550_GPIO17_INT, + AU1550_GPIO20_INT, + AU1550_GPIO21_INT, + AU1550_GPIO22_INT, + AU1550_GPIO23_INT, + AU1550_GPIO24_INT, + AU1550_GPIO25_INT, + AU1550_GPIO26_INT, + AU1550_GPIO27_INT, + AU1550_GPIO28_INT, + AU1550_GPIO206_INT, + AU1550_GPIO207_INT, + AU1550_GPIO208_215_INT, /* Logical or of GPIO208:215 */ +}; + +enum soc_au1200_ints { + AU1200_FIRST_INT = AU1000_INTC0_INT_BASE, + AU1200_UART0_INT = AU1200_FIRST_INT, + AU1200_SWT_INT, + AU1200_SD_INT, + AU1200_DDMA_INT, + AU1200_MAE_BE_INT, + AU1200_GPIO200_INT, + AU1200_GPIO201_INT, + AU1200_GPIO202_INT, + AU1200_UART1_INT, + AU1200_MAE_FE_INT, + AU1200_PSC0_INT, + AU1200_PSC1_INT, + AU1200_AES_INT, + AU1200_CAMERA_INT, + AU1200_TOY_INT, + AU1200_TOY_MATCH0_INT, + AU1200_TOY_MATCH1_INT, + AU1200_TOY_MATCH2_INT, + AU1200_RTC_INT, + AU1200_RTC_MATCH0_INT, + AU1200_RTC_MATCH1_INT, + AU1200_RTC_MATCH2_INT, + AU1200_GPIO203_INT, + AU1200_NAND_INT, + AU1200_GPIO204_INT, + AU1200_GPIO205_INT, + AU1200_GPIO206_INT, + AU1200_GPIO207_INT, + AU1200_GPIO208_215_INT, /* Logical OR of 208:215 */ + AU1200_USB_INT, + AU1200_LCD_INT, + AU1200_MAE_BOTH_INT, + AU1200_GPIO0_INT, + AU1200_GPIO1_INT, + AU1200_GPIO2_INT, + AU1200_GPIO3_INT, + AU1200_GPIO4_INT, + AU1200_GPIO5_INT, + AU1200_GPIO6_INT, + AU1200_GPIO7_INT, + AU1200_GPIO8_INT, + AU1200_GPIO9_INT, + AU1200_GPIO10_INT, + AU1200_GPIO11_INT, + AU1200_GPIO12_INT, + AU1200_GPIO13_INT, + AU1200_GPIO14_INT, + AU1200_GPIO15_INT, + AU1200_GPIO16_INT, + AU1200_GPIO17_INT, + AU1200_GPIO18_INT, + AU1200_GPIO19_INT, + AU1200_GPIO20_INT, + AU1200_GPIO21_INT, + AU1200_GPIO22_INT, + AU1200_GPIO23_INT, + AU1200_GPIO24_INT, + AU1200_GPIO25_INT, + AU1200_GPIO26_INT, + AU1200_GPIO27_INT, + AU1200_GPIO28_INT, + AU1200_GPIO29_INT, + AU1200_GPIO30_INT, + AU1200_GPIO31_INT, +}; #endif /* !defined (_LANGUAGE_ASSEMBLY) */ @@ -549,78 +911,16 @@ void au1xxx_setup_irqmap(struct au1xxx_irqmap *map, int count); #define IC1_TESTBIT 0xB1800080 -/* Interrupt Numbers */ + /* Au1000 */ #ifdef CONFIG_SOC_AU1000 -enum soc_au1000_ints { - AU1000_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, - AU1000_UART0_INT = AU1000_FIRST_INT, - AU1000_UART1_INT, /* au1000 */ - AU1000_UART2_INT, /* au1000 */ - AU1000_UART3_INT, - AU1000_SSI0_INT, /* au1000 */ - AU1000_SSI1_INT, /* au1000 */ - AU1000_DMA_INT_BASE, - - AU1000_TOY_INT = AU1000_FIRST_INT + 14, - AU1000_TOY_MATCH0_INT, - AU1000_TOY_MATCH1_INT, - AU1000_TOY_MATCH2_INT, - AU1000_RTC_INT, - AU1000_RTC_MATCH0_INT, - AU1000_RTC_MATCH1_INT, - AU1000_RTC_MATCH2_INT, - AU1000_IRDA_TX_INT, /* au1000 */ - AU1000_IRDA_RX_INT, /* au1000 */ - AU1000_USB_DEV_REQ_INT, - AU1000_USB_DEV_SUS_INT, - AU1000_USB_HOST_INT, - AU1000_ACSYNC_INT, - AU1000_MAC0_DMA_INT, - AU1000_MAC1_DMA_INT, - AU1000_I2S_UO_INT, /* au1000 */ - AU1000_AC97C_INT, - AU1000_GPIO_0, - AU1000_GPIO_1, - AU1000_GPIO_2, - AU1000_GPIO_3, - AU1000_GPIO_4, - AU1000_GPIO_5, - AU1000_GPIO_6, - AU1000_GPIO_7, - AU1000_GPIO_8, - AU1000_GPIO_9, - AU1000_GPIO_10, - AU1000_GPIO_11, - AU1000_GPIO_12, - AU1000_GPIO_13, - AU1000_GPIO_14, - AU1000_GPIO_15, - AU1000_GPIO_16, - AU1000_GPIO_17, - AU1000_GPIO_18, - AU1000_GPIO_19, - AU1000_GPIO_20, - AU1000_GPIO_21, - AU1000_GPIO_22, - AU1000_GPIO_23, - AU1000_GPIO_24, - AU1000_GPIO_25, - AU1000_GPIO_26, - AU1000_GPIO_27, - AU1000_GPIO_28, - AU1000_GPIO_29, - AU1000_GPIO_30, - AU1000_GPIO_31, -}; #define UART0_ADDR 0xB1100000 -#define UART1_ADDR 0xB1200000 -#define UART2_ADDR 0xB1300000 #define UART3_ADDR 0xB1400000 #define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */ #define USB_HOST_CONFIG 0xB017FFFC +#define FOR_PLATFORM_C_USB_HOST_INT AU1000_USB_HOST_INT #define AU1000_ETH0_BASE 0xB0500000 #define AU1000_ETH1_BASE 0xB0510000 @@ -631,78 +931,13 @@ enum soc_au1000_ints { /* Au1500 */ #ifdef CONFIG_SOC_AU1500 -enum soc_au1500_ints { - AU1500_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, - AU1500_UART0_INT = AU1500_FIRST_INT, - AU1000_PCI_INTA, /* au1500 */ - AU1000_PCI_INTB, /* au1500 */ - AU1500_UART3_INT, - AU1000_PCI_INTC, /* au1500 */ - AU1000_PCI_INTD, /* au1500 */ - AU1000_DMA_INT_BASE, - - AU1000_TOY_INT = AU1500_FIRST_INT + 14, - AU1000_TOY_MATCH0_INT, - AU1000_TOY_MATCH1_INT, - AU1000_TOY_MATCH2_INT, - AU1000_RTC_INT, - AU1000_RTC_MATCH0_INT, - AU1000_RTC_MATCH1_INT, - AU1000_RTC_MATCH2_INT, - AU1500_PCI_ERR_INT, - AU1500_RESERVED_INT, - AU1000_USB_DEV_REQ_INT, - AU1000_USB_DEV_SUS_INT, - AU1000_USB_HOST_INT, - AU1000_ACSYNC_INT, - AU1500_MAC0_DMA_INT, - AU1500_MAC1_DMA_INT, - AU1000_AC97C_INT = AU1500_FIRST_INT + 31, - AU1000_GPIO_0, - AU1000_GPIO_1, - AU1000_GPIO_2, - AU1000_GPIO_3, - AU1000_GPIO_4, - AU1000_GPIO_5, - AU1000_GPIO_6, - AU1000_GPIO_7, - AU1000_GPIO_8, - AU1000_GPIO_9, - AU1000_GPIO_10, - AU1000_GPIO_11, - AU1000_GPIO_12, - AU1000_GPIO_13, - AU1000_GPIO_14, - AU1000_GPIO_15, - AU1500_GPIO_200, - AU1500_GPIO_201, - AU1500_GPIO_202, - AU1500_GPIO_203, - AU1500_GPIO_20, - AU1500_GPIO_204, - AU1500_GPIO_205, - AU1500_GPIO_23, - AU1500_GPIO_24, - AU1500_GPIO_25, - AU1500_GPIO_26, - AU1500_GPIO_27, - AU1500_GPIO_28, - AU1500_GPIO_206, - AU1500_GPIO_207, - AU1500_GPIO_208_215, -}; - -/* shortcuts */ -#define INTA AU1000_PCI_INTA -#define INTB AU1000_PCI_INTB -#define INTC AU1000_PCI_INTC -#define INTD AU1000_PCI_INTD #define UART0_ADDR 0xB1100000 #define UART3_ADDR 0xB1400000 #define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */ #define USB_HOST_CONFIG 0xB017fffc +#define FOR_PLATFORM_C_USB_HOST_INT AU1500_USB_HOST_INT #define AU1500_ETH0_BASE 0xB1500000 #define AU1500_ETH1_BASE 0xB1510000 @@ -713,74 +948,13 @@ enum soc_au1500_ints { /* Au1100 */ #ifdef CONFIG_SOC_AU1100 -enum soc_au1100_ints { - AU1100_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, - AU1100_UART0_INT = AU1100_FIRST_INT, - AU1100_UART1_INT, - AU1100_SD_INT, - AU1100_UART3_INT, - AU1000_SSI0_INT, - AU1000_SSI1_INT, - AU1000_DMA_INT_BASE, - - AU1000_TOY_INT = AU1100_FIRST_INT + 14, - AU1000_TOY_MATCH0_INT, - AU1000_TOY_MATCH1_INT, - AU1000_TOY_MATCH2_INT, - AU1000_RTC_INT, - AU1000_RTC_MATCH0_INT, - AU1000_RTC_MATCH1_INT, - AU1000_RTC_MATCH2_INT, - AU1000_IRDA_TX_INT, - AU1000_IRDA_RX_INT, - AU1000_USB_DEV_REQ_INT, - AU1000_USB_DEV_SUS_INT, - AU1000_USB_HOST_INT, - AU1000_ACSYNC_INT, - AU1100_MAC0_DMA_INT, - AU1100_GPIO_208_215, - AU1100_LCD_INT, - AU1000_AC97C_INT, - AU1000_GPIO_0, - AU1000_GPIO_1, - AU1000_GPIO_2, - AU1000_GPIO_3, - AU1000_GPIO_4, - AU1000_GPIO_5, - AU1000_GPIO_6, - AU1000_GPIO_7, - AU1000_GPIO_8, - AU1000_GPIO_9, - AU1000_GPIO_10, - AU1000_GPIO_11, - AU1000_GPIO_12, - AU1000_GPIO_13, - AU1000_GPIO_14, - AU1000_GPIO_15, - AU1000_GPIO_16, - AU1000_GPIO_17, - AU1000_GPIO_18, - AU1000_GPIO_19, - AU1000_GPIO_20, - AU1000_GPIO_21, - AU1000_GPIO_22, - AU1000_GPIO_23, - AU1000_GPIO_24, - AU1000_GPIO_25, - AU1000_GPIO_26, - AU1000_GPIO_27, - AU1000_GPIO_28, - AU1000_GPIO_29, - AU1000_GPIO_30, - AU1000_GPIO_31, -}; #define UART0_ADDR 0xB1100000 -#define UART1_ADDR 0xB1200000 #define UART3_ADDR 0xB1400000 #define USB_OHCI_BASE 0x10100000 /* phys addr for ioremap */ #define USB_HOST_CONFIG 0xB017FFFC +#define FOR_PLATFORM_C_USB_HOST_INT AU1100_USB_HOST_INT #define AU1100_ETH0_BASE 0xB0500000 #define AU1100_MAC0_ENABLE 0xB0520000 @@ -788,87 +962,12 @@ enum soc_au1100_ints { #endif /* CONFIG_SOC_AU1100 */ #ifdef CONFIG_SOC_AU1550 -enum soc_au1550_ints { - AU1550_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, - AU1550_UART0_INT = AU1550_FIRST_INT, - AU1550_PCI_INTA, - AU1550_PCI_INTB, - AU1550_DDMA_INT, - AU1550_CRYPTO_INT, - AU1550_PCI_INTC, - AU1550_PCI_INTD, - AU1550_PCI_RST_INT, - AU1550_UART1_INT, - AU1550_UART3_INT, - AU1550_PSC0_INT, - AU1550_PSC1_INT, - AU1550_PSC2_INT, - AU1550_PSC3_INT, - AU1000_TOY_INT, - AU1000_TOY_MATCH0_INT, - AU1000_TOY_MATCH1_INT, - AU1000_TOY_MATCH2_INT, - AU1000_RTC_INT, - AU1000_RTC_MATCH0_INT, - AU1000_RTC_MATCH1_INT, - AU1000_RTC_MATCH2_INT, - - AU1550_NAND_INT = AU1550_FIRST_INT + 23, - AU1550_USB_DEV_REQ_INT, - AU1000_USB_DEV_REQ_INT = AU1550_USB_DEV_REQ_INT, - AU1550_USB_DEV_SUS_INT, - AU1000_USB_DEV_SUS_INT = AU1550_USB_DEV_SUS_INT, - AU1550_USB_HOST_INT, - AU1000_USB_HOST_INT = AU1550_USB_HOST_INT, - AU1550_MAC0_DMA_INT, - AU1550_MAC1_DMA_INT, - AU1000_GPIO_0 = AU1550_FIRST_INT + 32, - AU1000_GPIO_1, - AU1000_GPIO_2, - AU1000_GPIO_3, - AU1000_GPIO_4, - AU1000_GPIO_5, - AU1000_GPIO_6, - AU1000_GPIO_7, - AU1000_GPIO_8, - AU1000_GPIO_9, - AU1000_GPIO_10, - AU1000_GPIO_11, - AU1000_GPIO_12, - AU1000_GPIO_13, - AU1000_GPIO_14, - AU1000_GPIO_15, - AU1550_GPIO_200, - AU1500_GPIO_201_205, /* Logical or of GPIO201:205 */ - AU1500_GPIO_16, - AU1500_GPIO_17, - AU1500_GPIO_20, - AU1500_GPIO_21, - AU1500_GPIO_22, - AU1500_GPIO_23, - AU1500_GPIO_24, - AU1500_GPIO_25, - AU1500_GPIO_26, - AU1500_GPIO_27, - AU1500_GPIO_28, - AU1500_GPIO_206, - AU1500_GPIO_207, - AU1500_GPIO_208_218, /* Logical or of GPIO208:218 */ -}; - -/* shortcuts */ -#define INTA AU1550_PCI_INTA -#define INTB AU1550_PCI_INTB -#define INTC AU1550_PCI_INTC -#define INTD AU1550_PCI_INTD - #define UART0_ADDR 0xB1100000 -#define UART1_ADDR 0xB1200000 -#define UART3_ADDR 0xB1400000 #define USB_OHCI_BASE 0x14020000 /* phys addr for ioremap */ #define USB_OHCI_LEN 0x00060000 #define USB_HOST_CONFIG 0xB4027ffc +#define FOR_PLATFORM_C_USB_HOST_INT AU1550_USB_HOST_INT #define AU1550_ETH0_BASE 0xB0500000 #define AU1550_ETH1_BASE 0xB0510000 @@ -877,78 +976,10 @@ enum soc_au1550_ints { #define NUM_ETH_INTERFACES 2 #endif /* CONFIG_SOC_AU1550 */ + #ifdef CONFIG_SOC_AU1200 -enum soc_au1200_ints { - AU1200_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, - AU1200_UART0_INT = AU1200_FIRST_INT, - AU1200_SWT_INT, - AU1200_SD_INT, - AU1200_DDMA_INT, - AU1200_MAE_BE_INT, - AU1200_GPIO_200, - AU1200_GPIO_201, - AU1200_GPIO_202, - AU1200_UART1_INT, - AU1200_MAE_FE_INT, - AU1200_PSC0_INT, - AU1200_PSC1_INT, - AU1200_AES_INT, - AU1200_CAMERA_INT, - AU1000_TOY_INT, - AU1000_TOY_MATCH0_INT, - AU1000_TOY_MATCH1_INT, - AU1000_TOY_MATCH2_INT, - AU1000_RTC_INT, - AU1000_RTC_MATCH0_INT, - AU1000_RTC_MATCH1_INT, - AU1000_RTC_MATCH2_INT, - AU1200_GPIO_203, - AU1200_NAND_INT, - AU1200_GPIO_204, - AU1200_GPIO_205, - AU1200_GPIO_206, - AU1200_GPIO_207, - AU1200_GPIO_208_215, /* Logical OR of 208:215 */ - AU1200_USB_INT, - AU1000_USB_HOST_INT = AU1200_USB_INT, - AU1200_LCD_INT, - AU1200_MAE_BOTH_INT, - AU1000_GPIO_0, - AU1000_GPIO_1, - AU1000_GPIO_2, - AU1000_GPIO_3, - AU1000_GPIO_4, - AU1000_GPIO_5, - AU1000_GPIO_6, - AU1000_GPIO_7, - AU1000_GPIO_8, - AU1000_GPIO_9, - AU1000_GPIO_10, - AU1000_GPIO_11, - AU1000_GPIO_12, - AU1000_GPIO_13, - AU1000_GPIO_14, - AU1000_GPIO_15, - AU1000_GPIO_16, - AU1000_GPIO_17, - AU1000_GPIO_18, - AU1000_GPIO_19, - AU1000_GPIO_20, - AU1000_GPIO_21, - AU1000_GPIO_22, - AU1000_GPIO_23, - AU1000_GPIO_24, - AU1000_GPIO_25, - AU1000_GPIO_26, - AU1000_GPIO_27, - AU1000_GPIO_28, - AU1000_GPIO_29, - AU1000_GPIO_30, - AU1000_GPIO_31, -}; #define UART0_ADDR 0xB1100000 -#define UART1_ADDR 0xB1200000 #define USB_UOC_BASE 0x14020020 #define USB_UOC_LEN 0x20 @@ -974,15 +1005,9 @@ enum soc_au1200_ints { #define USBMSRMCFG_RDCOMB 30 #define USBMSRMCFG_PFEN 31 -#endif /* CONFIG_SOC_AU1200 */ - -#define AU1000_INTC0_INT_BASE (MIPS_CPU_IRQ_BASE + 8) -#define AU1000_INTC0_INT_LAST (AU1000_INTC0_INT_BASE + 31) -#define AU1000_INTC1_INT_BASE (AU1000_INTC0_INT_BASE + 32) -#define AU1000_INTC1_INT_LAST (AU1000_INTC1_INT_BASE + 31) +#define FOR_PLATFORM_C_USB_HOST_INT AU1200_USB_INT -#define AU1000_MAX_INTR AU1000_INTC1_INT_LAST -#define INTX 0xFF /* not valid */ +#endif /* CONFIG_SOC_AU1200 */ /* Programmable Counters 0 and 1 */ #define SYS_BASE 0xB1900000 @@ -1231,14 +1256,6 @@ enum soc_au1200_ints { #define MAC_RX_BUFF3_STATUS 0x30 #define MAC_RX_BUFF3_ADDR 0x34 -/* UARTS 0-3 */ -#define UART_BASE UART0_ADDR -#ifdef CONFIG_SOC_AU1200 -#define UART_DEBUG_BASE UART1_ADDR -#else -#define UART_DEBUG_BASE UART3_ADDR -#endif - #define UART_RX 0 /* Receive buffer */ #define UART_TX 4 /* Transmit buffer */ #define UART_IER 8 /* Interrupt Enable Register */ @@ -1251,84 +1268,6 @@ enum soc_au1200_ints { #define UART_CLK 0x28 /* Baud Rate Clock Divider */ #define UART_MOD_CNTRL 0x100 /* Module Control */ -#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */ -#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */ -#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */ -#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */ -#define UART_FCR_TRIGGER_MASK 0xF0 /* Mask for the FIFO trigger range */ -#define UART_FCR_R_TRIGGER_1 0x00 /* Mask for receive trigger set at 1 */ -#define UART_FCR_R_TRIGGER_4 0x40 /* Mask for receive trigger set at 4 */ -#define UART_FCR_R_TRIGGER_8 0x80 /* Mask for receive trigger set at 8 */ -#define UART_FCR_R_TRIGGER_14 0xA0 /* Mask for receive trigger set at 14 */ -#define UART_FCR_T_TRIGGER_0 0x00 /* Mask for transmit trigger set at 0 */ -#define UART_FCR_T_TRIGGER_4 0x10 /* Mask for transmit trigger set at 4 */ -#define UART_FCR_T_TRIGGER_8 0x20 /* Mask for transmit trigger set at 8 */ -#define UART_FCR_T_TRIGGER_12 0x30 /* Mask for transmit trigger set at 12 */ - -/* - * These are the definitions for the Line Control Register - */ -#define UART_LCR_SBC 0x40 /* Set break control */ -#define UART_LCR_SPAR 0x20 /* Stick parity (?) */ -#define UART_LCR_EPAR 0x10 /* Even parity select */ -#define UART_LCR_PARITY 0x08 /* Parity Enable */ -#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */ -#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */ -#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */ -#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */ -#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */ - -/* - * These are the definitions for the Line Status Register - */ -#define UART_LSR_TEMT 0x40 /* Transmitter empty */ -#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */ -#define UART_LSR_BI 0x10 /* Break interrupt indicator */ -#define UART_LSR_FE 0x08 /* Frame error indicator */ -#define UART_LSR_PE 0x04 /* Parity error indicator */ -#define UART_LSR_OE 0x02 /* Overrun error indicator */ -#define UART_LSR_DR 0x01 /* Receiver data ready */ - -/* - * These are the definitions for the Interrupt Identification Register - */ -#define UART_IIR_NO_INT 0x01 /* No interrupts pending */ -#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */ -#define UART_IIR_MSI 0x00 /* Modem status interrupt */ -#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */ -#define UART_IIR_RDI 0x04 /* Receiver data interrupt */ -#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */ - -/* - * These are the definitions for the Interrupt Enable Register - */ -#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */ -#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */ -#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */ -#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */ - -/* - * These are the definitions for the Modem Control Register - */ -#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */ -#define UART_MCR_OUT2 0x08 /* Out2 complement */ -#define UART_MCR_OUT1 0x04 /* Out1 complement */ -#define UART_MCR_RTS 0x02 /* RTS complement */ -#define UART_MCR_DTR 0x01 /* DTR complement */ - -/* - * These are the definitions for the Modem Status Register - */ -#define UART_MSR_DCD 0x80 /* Data Carrier Detect */ -#define UART_MSR_RI 0x40 /* Ring Indicator */ -#define UART_MSR_DSR 0x20 /* Data Set Ready */ -#define UART_MSR_CTS 0x10 /* Clear to Send */ -#define UART_MSR_DDCD 0x08 /* Delta DCD */ -#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */ -#define UART_MSR_DDSR 0x02 /* Delta DSR */ -#define UART_MSR_DCTS 0x01 /* Delta CTS */ -#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */ - /* SSIO */ #define SSI0_STATUS 0xB1600000 # define SSI_STATUS_BF (1 << 4) @@ -1720,7 +1659,7 @@ enum soc_au1200_ints { #define IOPORT_RESOURCE_START 0x00001000 /* skip legacy probing */ #define IOPORT_RESOURCE_END 0xffffffff #define IOMEM_RESOURCE_START 0x10000000 -#define IOMEM_RESOURCE_END 0xffffffff +#define IOMEM_RESOURCE_END 0xfffffffffULL #else /* Au1000 and Au1100 and Au1200 */ @@ -1728,7 +1667,7 @@ enum soc_au1200_ints { #define IOPORT_RESOURCE_START 0x10000000 #define IOPORT_RESOURCE_END 0xffffffff #define IOMEM_RESOURCE_START 0x10000000 -#define IOMEM_RESOURCE_END 0xffffffff +#define IOMEM_RESOURCE_END 0xfffffffffULL #define PCI_IO_START 0 #define PCI_IO_END 0 @@ -1739,53 +1678,4 @@ enum soc_au1200_ints { #endif -#ifndef _LANGUAGE_ASSEMBLY -typedef volatile struct { - /* 0x0000 */ u32 toytrim; - /* 0x0004 */ u32 toywrite; - /* 0x0008 */ u32 toymatch0; - /* 0x000C */ u32 toymatch1; - /* 0x0010 */ u32 toymatch2; - /* 0x0014 */ u32 cntrctrl; - /* 0x0018 */ u32 scratch0; - /* 0x001C */ u32 scratch1; - /* 0x0020 */ u32 freqctrl0; - /* 0x0024 */ u32 freqctrl1; - /* 0x0028 */ u32 clksrc; - /* 0x002C */ u32 pinfunc; - /* 0x0030 */ u32 reserved0; - /* 0x0034 */ u32 wakemsk; - /* 0x0038 */ u32 endian; - /* 0x003C */ u32 powerctrl; - /* 0x0040 */ u32 toyread; - /* 0x0044 */ u32 rtctrim; - /* 0x0048 */ u32 rtcwrite; - /* 0x004C */ u32 rtcmatch0; - /* 0x0050 */ u32 rtcmatch1; - /* 0x0054 */ u32 rtcmatch2; - /* 0x0058 */ u32 rtcread; - /* 0x005C */ u32 wakesrc; - /* 0x0060 */ u32 cpupll; - /* 0x0064 */ u32 auxpll; - /* 0x0068 */ u32 reserved1; - /* 0x006C */ u32 reserved2; - /* 0x0070 */ u32 reserved3; - /* 0x0074 */ u32 reserved4; - /* 0x0078 */ u32 slppwr; - /* 0x007C */ u32 sleep; - /* 0x0080 */ u32 reserved5[32]; - /* 0x0100 */ u32 trioutrd; -#define trioutclr trioutrd - /* 0x0104 */ u32 reserved6; - /* 0x0108 */ u32 outputrd; -#define outputset outputrd - /* 0x010C */ u32 outputclr; - /* 0x0110 */ u32 pinstaterd; -#define pininputen pinstaterd -} AU1X00_SYS; - -static AU1X00_SYS * const sys = (AU1X00_SYS *)SYS_BASE; - -#endif - #endif diff --git a/arch/mips/include/asm/mach-au1x00/au1100_mmc.h b/arch/mips/include/asm/mach-au1x00/au1100_mmc.h index c35e20918490..94000a3b6f0b 100644 --- a/arch/mips/include/asm/mach-au1x00/au1100_mmc.h +++ b/arch/mips/include/asm/mach-au1x00/au1100_mmc.h @@ -46,6 +46,7 @@ struct au1xmmc_platform_data { int(*card_readonly)(void *mmc_host); void(*set_power)(void *mmc_host, int state); struct led_classdev *led; + unsigned long mask_host_caps; }; #define SD0_BASE 0xB0600000 @@ -205,4 +206,3 @@ struct au1xmmc_platform_data { #endif /* __ASM_AU1100_MMC_H */ - diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h b/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h index 06f68f43800a..8c6b1105ce0b 100644 --- a/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h +++ b/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h @@ -305,6 +305,7 @@ typedef struct dbdma_chan_config { dbdev_tab_t *chan_dest; au1x_dma_chan_t *chan_ptr; au1x_ddma_desc_t *chan_desc_base; + u32 cdb_membase; /* kmalloc base of above */ au1x_ddma_desc_t *get_ptr, *put_ptr, *cur_ptr; void *chan_callparam; void (*chan_callback)(int, void *); @@ -338,8 +339,8 @@ u32 au1xxx_dbdma_set_devwidth(u32 chanid, int bits); u32 au1xxx_dbdma_ring_alloc(u32 chanid, int entries); /* Put buffers on source/destination descriptors. */ -u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags); -u32 _au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags); +u32 au1xxx_dbdma_put_source(u32 chanid, dma_addr_t buf, int nbytes, u32 flags); +u32 au1xxx_dbdma_put_dest(u32 chanid, dma_addr_t buf, int nbytes, u32 flags); /* Get a buffer from the destination descriptor. */ u32 au1xxx_dbdma_get_dest(u32 chanid, void **buf, int *nbytes); @@ -362,25 +363,6 @@ void au1xxx_dbdma_suspend(void); void au1xxx_dbdma_resume(void); #endif - -/* - * Some compatibilty macros -- needed to make changes to API - * without breaking existing drivers. - */ -#define au1xxx_dbdma_put_source(chanid, buf, nbytes) \ - _au1xxx_dbdma_put_source(chanid, buf, nbytes, DDMA_FLAGS_IE) -#define au1xxx_dbdma_put_source_flags(chanid, buf, nbytes, flags) \ - _au1xxx_dbdma_put_source(chanid, buf, nbytes, flags) -#define put_source_flags(chanid, buf, nbytes, flags) \ - au1xxx_dbdma_put_source_flags(chanid, buf, nbytes, flags) - -#define au1xxx_dbdma_put_dest(chanid, buf, nbytes) \ - _au1xxx_dbdma_put_dest(chanid, buf, nbytes, DDMA_FLAGS_IE) -#define au1xxx_dbdma_put_dest_flags(chanid, buf, nbytes, flags) \ - _au1xxx_dbdma_put_dest(chanid, buf, nbytes, flags) -#define put_dest_flags(chanid, buf, nbytes, flags) \ - au1xxx_dbdma_put_dest_flags(chanid, buf, nbytes, flags) - /* * Flags for the put_source/put_dest functions. */ diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_eth.h b/arch/mips/include/asm/mach-au1x00/au1xxx_eth.h new file mode 100644 index 000000000000..bae9b758fcde --- /dev/null +++ b/arch/mips/include/asm/mach-au1x00/au1xxx_eth.h @@ -0,0 +1,17 @@ +#ifndef __AU1X00_ETH_DATA_H +#define __AU1X00_ETH_DATA_H + +/* Platform specific PHY configuration passed to the MAC driver */ +struct au1000_eth_platform_data { + int phy_static_config; + int phy_search_highest_addr; + int phy1_search_mac0; + int phy_addr; + int phy_busid; + int phy_irq; +}; + +void __init au1xxx_override_eth_cfg(unsigned port, + struct au1000_eth_platform_data *eth_data); + +#endif /* __AU1X00_ETH_DATA_H */ diff --git a/arch/mips/include/asm/mach-au1x00/gpio-au1000.h b/arch/mips/include/asm/mach-au1x00/gpio-au1000.h index 91595fa89034..62d2f136d941 100644 --- a/arch/mips/include/asm/mach-au1x00/gpio-au1000.h +++ b/arch/mips/include/asm/mach-au1x00/gpio-au1000.h @@ -35,15 +35,13 @@ static inline int au1000_gpio2_to_irq(int gpio) return -ENXIO; } -#ifdef CONFIG_SOC_AU1000 static inline int au1000_irq_to_gpio(int irq) { - if ((irq >= AU1000_GPIO_0) && (irq <= AU1000_GPIO_31)) - return ALCHEMY_GPIO1_BASE + (irq - AU1000_GPIO_0) + 0; + if ((irq >= AU1000_GPIO0_INT) && (irq <= AU1000_GPIO31_INT)) + return ALCHEMY_GPIO1_BASE + (irq - AU1000_GPIO0_INT) + 0; return -ENXIO; } -#endif static inline int au1500_gpio1_to_irq(int gpio) { @@ -71,27 +69,25 @@ static inline int au1500_gpio2_to_irq(int gpio) return -ENXIO; } -#ifdef CONFIG_SOC_AU1500 static inline int au1500_irq_to_gpio(int irq) { switch (irq) { - case AU1000_GPIO_0 ... AU1000_GPIO_15: - case AU1500_GPIO_20: - case AU1500_GPIO_23 ... AU1500_GPIO_28: - return ALCHEMY_GPIO1_BASE + (irq - AU1000_GPIO_0) + 0; - case AU1500_GPIO_200 ... AU1500_GPIO_203: - return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO_200) + 0; - case AU1500_GPIO_204 ... AU1500_GPIO_205: - return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO_204) + 4; - case AU1500_GPIO_206 ... AU1500_GPIO_207: - return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO_206) + 6; - case AU1500_GPIO_208_215: + case AU1500_GPIO0_INT ... AU1500_GPIO15_INT: + case AU1500_GPIO20_INT: + case AU1500_GPIO23_INT ... AU1500_GPIO28_INT: + return ALCHEMY_GPIO1_BASE + (irq - AU1500_GPIO0_INT) + 0; + case AU1500_GPIO200_INT ... AU1500_GPIO203_INT: + return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO200_INT) + 0; + case AU1500_GPIO204_INT ... AU1500_GPIO205_INT: + return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO204_INT) + 4; + case AU1500_GPIO206_INT ... AU1500_GPIO207_INT: + return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO206_INT) + 6; + case AU1500_GPIO208_215_INT: return ALCHEMY_GPIO2_BASE + 8; } return -ENXIO; } -#endif static inline int au1100_gpio1_to_irq(int gpio) { @@ -108,19 +104,17 @@ static inline int au1100_gpio2_to_irq(int gpio) return -ENXIO; } -#ifdef CONFIG_SOC_AU1100 static inline int au1100_irq_to_gpio(int irq) { switch (irq) { - case AU1000_GPIO_0 ... AU1000_GPIO_31: - return ALCHEMY_GPIO1_BASE + (irq - AU1000_GPIO_0) + 0; - case AU1100_GPIO_208_215: + case AU1100_GPIO0_INT ... AU1100_GPIO31_INT: + return ALCHEMY_GPIO1_BASE + (irq - AU1100_GPIO0_INT) + 0; + case AU1100_GPIO208_215_INT: return ALCHEMY_GPIO2_BASE + 8; } return -ENXIO; } -#endif static inline int au1550_gpio1_to_irq(int gpio) { @@ -149,24 +143,22 @@ static inline int au1550_gpio2_to_irq(int gpio) return -ENXIO; } -#ifdef CONFIG_SOC_AU1550 static inline int au1550_irq_to_gpio(int irq) { switch (irq) { - case AU1000_GPIO_0 ... AU1000_GPIO_15: - return ALCHEMY_GPIO1_BASE + (irq - AU1000_GPIO_0) + 0; - case AU1550_GPIO_200: - case AU1500_GPIO_201_205: - return ALCHEMY_GPIO2_BASE + (irq - AU1550_GPIO_200) + 0; - case AU1500_GPIO_16 ... AU1500_GPIO_28: - return ALCHEMY_GPIO1_BASE + (irq - AU1500_GPIO_16) + 16; - case AU1500_GPIO_206 ... AU1500_GPIO_208_218: - return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO_206) + 6; + case AU1550_GPIO0_INT ... AU1550_GPIO15_INT: + return ALCHEMY_GPIO1_BASE + (irq - AU1550_GPIO0_INT) + 0; + case AU1550_GPIO200_INT: + case AU1550_GPIO201_205_INT: + return ALCHEMY_GPIO2_BASE + (irq - AU1550_GPIO200_INT) + 0; + case AU1550_GPIO16_INT ... AU1550_GPIO28_INT: + return ALCHEMY_GPIO1_BASE + (irq - AU1550_GPIO16_INT) + 16; + case AU1550_GPIO206_INT ... AU1550_GPIO208_215_INT: + return ALCHEMY_GPIO2_BASE + (irq - AU1550_GPIO206_INT) + 6; } return -ENXIO; } -#endif static inline int au1200_gpio1_to_irq(int gpio) { @@ -187,23 +179,21 @@ static inline int au1200_gpio2_to_irq(int gpio) return -ENXIO; } -#ifdef CONFIG_SOC_AU1200 static inline int au1200_irq_to_gpio(int irq) { switch (irq) { - case AU1000_GPIO_0 ... AU1000_GPIO_31: - return ALCHEMY_GPIO1_BASE + (irq - AU1000_GPIO_0) + 0; - case AU1200_GPIO_200 ... AU1200_GPIO_202: - return ALCHEMY_GPIO2_BASE + (irq - AU1200_GPIO_200) + 0; - case AU1200_GPIO_203: + case AU1200_GPIO0_INT ... AU1200_GPIO31_INT: + return ALCHEMY_GPIO1_BASE + (irq - AU1200_GPIO0_INT) + 0; + case AU1200_GPIO200_INT ... AU1200_GPIO202_INT: + return ALCHEMY_GPIO2_BASE + (irq - AU1200_GPIO200_INT) + 0; + case AU1200_GPIO203_INT: return ALCHEMY_GPIO2_BASE + 3; - case AU1200_GPIO_204 ... AU1200_GPIO_208_215: - return ALCHEMY_GPIO2_BASE + (irq - AU1200_GPIO_204) + 4; + case AU1200_GPIO204_INT ... AU1200_GPIO208_215_INT: + return ALCHEMY_GPIO2_BASE + (irq - AU1200_GPIO204_INT) + 4; } return -ENXIO; } -#endif /* * GPIO1 block macros for common linux gpio functions. @@ -246,19 +236,19 @@ static inline int alchemy_gpio1_is_valid(int gpio) static inline int alchemy_gpio1_to_irq(int gpio) { -#if defined(CONFIG_SOC_AU1000) - return au1000_gpio1_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1100) - return au1100_gpio1_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1500) - return au1500_gpio1_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1550) - return au1550_gpio1_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1200) - return au1200_gpio1_to_irq(gpio); -#else + switch (alchemy_get_cputype()) { + case ALCHEMY_CPU_AU1000: + return au1000_gpio1_to_irq(gpio); + case ALCHEMY_CPU_AU1100: + return au1100_gpio1_to_irq(gpio); + case ALCHEMY_CPU_AU1500: + return au1500_gpio1_to_irq(gpio); + case ALCHEMY_CPU_AU1550: + return au1550_gpio1_to_irq(gpio); + case ALCHEMY_CPU_AU1200: + return au1200_gpio1_to_irq(gpio); + } return -ENXIO; -#endif } /* @@ -316,19 +306,19 @@ static inline int alchemy_gpio2_is_valid(int gpio) static inline int alchemy_gpio2_to_irq(int gpio) { -#if defined(CONFIG_SOC_AU1000) - return au1000_gpio2_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1100) - return au1100_gpio2_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1500) - return au1500_gpio2_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1550) - return au1550_gpio2_to_irq(gpio); -#elif defined(CONFIG_SOC_AU1200) - return au1200_gpio2_to_irq(gpio); -#else + switch (alchemy_get_cputype()) { + case ALCHEMY_CPU_AU1000: + return au1000_gpio2_to_irq(gpio); + case ALCHEMY_CPU_AU1100: + return au1100_gpio2_to_irq(gpio); + case ALCHEMY_CPU_AU1500: + return au1500_gpio2_to_irq(gpio); + case ALCHEMY_CPU_AU1550: + return au1550_gpio2_to_irq(gpio); + case ALCHEMY_CPU_AU1200: + return au1200_gpio2_to_irq(gpio); + } return -ENXIO; -#endif } /**********************************************************************/ @@ -384,10 +374,13 @@ static inline void alchemy_gpio2_enable_int(int gpio2) gpio2 -= ALCHEMY_GPIO2_BASE; -#if defined(CONFIG_SOC_AU1100) || defined(CONFIG_SOC_AU1500) /* Au1100/Au1500 have GPIO208-215 enable bits at 0..7 */ - gpio2 -= 8; -#endif + switch (alchemy_get_cputype()) { + case ALCHEMY_CPU_AU1100: + case ALCHEMY_CPU_AU1500: + gpio2 -= 8; + } + local_irq_save(flags); __alchemy_gpio2_mod_int(gpio2, 1); local_irq_restore(flags); @@ -405,10 +398,13 @@ static inline void alchemy_gpio2_disable_int(int gpio2) gpio2 -= ALCHEMY_GPIO2_BASE; -#if defined(CONFIG_SOC_AU1100) || defined(CONFIG_SOC_AU1500) /* Au1100/Au1500 have GPIO208-215 enable bits at 0..7 */ - gpio2 -= 8; -#endif + switch (alchemy_get_cputype()) { + case ALCHEMY_CPU_AU1100: + case ALCHEMY_CPU_AU1500: + gpio2 -= 8; + } + local_irq_save(flags); __alchemy_gpio2_mod_int(gpio2, 0); local_irq_restore(flags); @@ -494,19 +490,19 @@ static inline int alchemy_gpio_to_irq(int gpio) static inline int alchemy_irq_to_gpio(int irq) { -#if defined(CONFIG_SOC_AU1000) - return au1000_irq_to_gpio(irq); -#elif defined(CONFIG_SOC_AU1100) - return au1100_irq_to_gpio(irq); -#elif defined(CONFIG_SOC_AU1500) - return au1500_irq_to_gpio(irq); -#elif defined(CONFIG_SOC_AU1550) - return au1550_irq_to_gpio(irq); -#elif defined(CONFIG_SOC_AU1200) - return au1200_irq_to_gpio(irq); -#else + switch (alchemy_get_cputype()) { + case ALCHEMY_CPU_AU1000: + return au1000_irq_to_gpio(irq); + case ALCHEMY_CPU_AU1100: + return au1100_irq_to_gpio(irq); + case ALCHEMY_CPU_AU1500: + return au1500_irq_to_gpio(irq); + case ALCHEMY_CPU_AU1550: + return au1550_irq_to_gpio(irq); + case ALCHEMY_CPU_AU1200: + return au1200_irq_to_gpio(irq); + } return -ENXIO; -#endif } /**********************************************************************/ diff --git a/arch/mips/include/asm/mach-au1x00/gpio.h b/arch/mips/include/asm/mach-au1x00/gpio.h index f9b7d41c659a..c3f60cdc3203 100644 --- a/arch/mips/include/asm/mach-au1x00/gpio.h +++ b/arch/mips/include/asm/mach-au1x00/gpio.h @@ -1,7 +1,7 @@ #ifndef _ALCHEMY_GPIO_H_ #define _ALCHEMY_GPIO_H_ -#if defined(CONFIG_ALCHEMY_GPIO_AU1000) +#if defined(CONFIG_ALCHEMY_GPIOINT_AU1000) #include <asm/mach-au1x00/gpio-au1000.h> diff --git a/arch/mips/include/asm/mach-au1x00/ioremap.h b/arch/mips/include/asm/mach-au1x00/ioremap.h index 364cea2dc71f..75a94ad3ac91 100644 --- a/arch/mips/include/asm/mach-au1x00/ioremap.h +++ b/arch/mips/include/asm/mach-au1x00/ioremap.h @@ -11,7 +11,7 @@ #include <linux/types.h> -#ifdef CONFIG_64BIT_PHYS_ADDR +#if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_PCI) extern phys_t __fixup_bigphys_addr(phys_t, phys_t); #else static inline phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size) diff --git a/arch/mips/include/asm/mach-au1x00/prom.h b/arch/mips/include/asm/mach-au1x00/prom.h index e38715577c51..4c0e09cf1735 100644 --- a/arch/mips/include/asm/mach-au1x00/prom.h +++ b/arch/mips/include/asm/mach-au1x00/prom.h @@ -6,7 +6,6 @@ extern char **prom_argv; extern char **prom_envp; extern void prom_init_cmdline(void); -extern char *prom_getcmdline(void); extern char *prom_getenv(char *envname); extern int prom_get_ethernet_addr(char *ethernet_addr); |