| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The SPI_MASTER_NO_TX bit (can't do buffer write) wasn't tested. This
code was introduced in commit 3c8e1a84 (spi/spi-gpio: add support for
controllers without MISO or MOSI pin). This patch fixes a bug in
choosing which transfer ops to use.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
There are some boards that do not strictly follow SPI standard and use
only 3 wires (SCLK, MOSI or MISO, SS) for connecting some simple auxiliary
chips and controls them with GPIO based 'spi controller'. In this
configuration the MISO or MOSI line is missing (it is not required if the
chip does not transfer any data back to host or host only reads data from
chip).
This patch adds support for such non-standard configuration in GPIO-based
SPI controller. It has been tested in configuration without MISO pin.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds a new flags argument to bitbang_txrx_be_cpha0 and
bitbang_txrx_be_cpha1 transfer functions. This enables support for
SPI_MASTER_NO_{TX,RX} transfer modes. The change should have no impact
on speed of the existing drivers. bitbank_txrx_* functions are usually
inlined into the drivers. When the argument is equal to constant zero,
the optimizer would be able to eliminate the dead code (flags checks)
easily. Tested on ARM and GCC 4.4.x and in all cases the checks were
eliminated in the inlined function.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
A number of files in drivers/spi fail checkincludes.pl due to the double
include of <linux/spi/spi_bitbang.h>.
The first include is needed to get the struct spi_bitbang definition and
the spi_bitbang_* function prototypes.
The second include happens after defining EXPAND_BITBANG_TXRX to get the
inlined bitbang_txrx_* utility functions.
The <linux/spi/spi_bitbang.h> header is also included by a number of other
spi drivers, as well as some arch/ code, in order to use struct spi_bitbang
and the associated functions.
To fix the double include, and remove any potential confusion about it, move
the inlined bitbang_txrx_* functions to a new private header in drivers/spi
and also remove the need to define EXPAND_BITBANG_TXRX.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Change spi-gpio so that it is possible to drive SPI communications over
GPIO without the need for a chipselect signal.
This is useful in very small setups where there's only one slave device
on the bus.
This patch does not affect existing setups.
I use this for a tiny communication channel between an embedded device and
a microcontroller. There are not enough GPIOs available for chipselect
and it's not needed anyway in this case.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cc: dbrownell@users.sourceforge.net
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
|
|
gpio_get_value() returns 0 or nonzero, but getmiso() expects 0 or 1.
Sanitize the value to a 0/1 boolean.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data. Such SPI masters support:
- any number of bus instances (bus_num is the platform_device.id)
- any number of chipselects (one GPIO per spi_device)
- all four SPI_MODE values, and SPI_CS_HIGH
- i/o word sizes from 1 to 32 bits;
- devices configured as with any other spi_master controller
When configured using platform_data, this provides relatively low clock
rates. On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)
Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
