1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify
# it under the terms of the GNU Lesser General Public License as
# published by the Free Software Foundation; either version 2.1 of the
# License, or (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, write to the Free Software Foundation,
# Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
; Common part of all paths
; So here's generally how mixer paths are used by PA: PA goes through
; a mixer path file from top to bottom and checks if a mixer element
; described therein exists. If so it is added to the list of mixer
; elements PA will control, keeping the order it read them in. If a
; mixer element described here has set the required= or
; required-absent= directives a path might not be accepted as valid
; and is ignored in its entirety (see below). However usually if a
; element listed here is missing this one element is ignored but not
; the entire path.
;
; When a device shall be muted/unmuted *all* elements listed in a path
; file with "switch = mute" will be toggled.
;
; When a device shall change its volume, PA will got through the list
; of all elements with "volume = merge" and set the volume on the
; first element. If that element does not support dB volumes, this is
; where the story ends. If it does support dB volumes, PA divides the
; requested volume by the volume that was set on this element, and
; then go on to the next element with "volume = merge" and then set
; that there, and so on. That way the first volume element in the
; path will be the one that does the 'biggest' part of the overall
; volume adjustment, with the remaining elements usually being set to
; some value next to 0dB. This logic makes sure we get the full range
; over all volume sliders and a very high granularity of volumes
; already in hardware.
;
; All switches and enumerations set to "select" are exposed via the
; "port" functionality of sinks/sources. Basically every possible
; switch setting and every possible enumeration setting will be
; combined and made into a "port". So make sure you don't list too
; many switches/enums for exposing, because the number of ports might
; rise exponentially.
;
; Only one path can be selected at a time. All paths that are valid
; for an audio device will be exposed as "port" for the sink/source.
; [General]
; priority = ... # Priority for this path
; description = ...
;
; [Option ...:...] # For each option of an enumeration or switch element
; # that shall be exposed as a sink/source port. Needs to
; # be named after the Element, followed by a colon, followed
; # by the option name, resp. on/off if the element is a switch.
; name = ... # Logical name to use in the path identifier
; priority = ... # Priority if this is made into a device port
;
; [Element ...] # For each element that we shall control
; required = ignore | switch | volume | enumeration | any # If set, require this element to be of this kind and available,
; # otherwise don't consider this path valid for the card
; required-absent = ignore | switch | volume # If set, require this element to not be of this kind and not
; # available, otherwise don't consider this path valid for the card
;
; switch = ignore | mute | off | on | select # What to do with this switch: ignore it, make it follow mute status,
; # always set it to off, always to on, or make it selectable as port.
; # If set to 'select' you need to define an Option section for on
; # and off
; volume = ignore | merge | off | zero # What to do with this volume: ignore it, merge it into the device
; # volume slider, always set it to the lowest value possible, or always
; # set it to 0 dB (for whatever that means)
; enumeration = ignore | select # What to do with this enumeration, ignore it or make it selectable
; # via device ports. If set to 'select' you need to define an Option section
; # for each of the items you want to expose
; direction = playback | capture # Is this relevant only for playback or capture? If not set this will implicitly be
; # set the direction of the PCM device is opened as. Generally this doesn't need to be set
; # unless you have a broken driver that has playback controls marked for capture or vice
; # versa
; direction-try-other = no | yes # If the element does not supported what is requested, try the other direction, too?
;
; override-map.1 = ... # Override the channel mask of the mixer control if the control only exposes a single channel
; override-map.2 = ... # Override the channel masks of the mixer control if the control only exposes two channels
; # Override maps should list for each element channel which high-level channels it controls via a
; # channel mask. A channel mask may either be the name of a single channel, or the words "all-left",
; # "all-right", "all-center", "all-front", "all-rear", and "all" to encode a specific subset of
; # channels in a mask
[Element PCM]
switch = mute
volume = merge
override-map.1 = all
override-map.2 = all-left,all-right
[Element External Amplifier]
switch = select
[Option External Amplifier:on]
name = output-amplifier-on
priority = 10
[Option External Amplifier:off]
name = output-amplifier-off
priority = 0
;;; 'Analog Output'
[Element Analog Output]
enumeration = select
[Option Analog Output:Speakers]
name = output-speaker
priority = 10
[Option Analog Output:Headphones]
name = output-headphones
priority = 9
[Option Analog Output:FP Headphones]
name = output-headphones
priority = 8
|
