'\" t
.\" This manpage is Copyright (C) 1996 Michael Haardt.
.\" Updates Nov 1998, Andries Brouwer
.\"
.\" %%%LICENSE_START(VERBATIM)
.\" Permission is granted to make and distribute verbatim copies of this
.\" manual provided the copyright notice and this permission notice are
.\" preserved on all copies.
.\"
.\" Permission is granted to copy and distribute modified versions of this
.\" manual under the conditions for verbatim copying, provided that the
.\" entire resulting derived work is distributed under the terms of a
.\" permission notice identical to this one.
.\"
.\" Since the Linux kernel and libraries are constantly changing, this
.\" manual page may be incorrect or out-of-date.  The author(s) assume no
.\" responsibility for errors or omissions, or for damages resulting from
.\" the use of the information contained herein.  The author(s) may not
.\" have taken the same level of care in the production of this manual,
.\" which is licensed free of charge, as they might when working
.\" professionally.
.\"
.\" Formatted or processed versions of this manual, if unaccompanied by
.\" the source, must acknowledge the copyright and authors of this work.
.\" %%%LICENSE_END
.TH MOUSE 4 1996-02-10 "Linux" "Linux Programmer's Manual"
.SH NAME
mouse \- serial mouse interface
.SH CONFIGURATION
Serial mice are connected to a serial RS232/V24 dialout line, see
.BR ttyS (4)
for a description.
.SH DESCRIPTION
.SS Introduction
The pinout of the usual 9 pin plug as used for serial mice is:
.TS
center;
r c l.
pin	name	used for
2	RX	Data
3	TX	\-12 V, Imax = 10 mA
4	DTR	+12 V, Imax = 10 mA
7	RTS	+12 V, Imax = 10 mA
5	GND	Ground
.TE

This is the specification, in fact 9 V suffices with most mice.
.PP
The mouse driver can recognize a mouse by dropping RTS to low and raising
it again.
About 14 ms later the mouse will send 0x4D (\(aqM\(aq) on the data line.
After a further 63 ms, a Microsoft-compatible 3-button mouse will send
0x33 (\(aq3\(aq).
.PP
The relative mouse movement is sent as \fIdx\fP (positive means right)
and \fIdy\fP (positive means down).
Various mice can operate at different speeds.
To select speeds, cycle through the
speeds 9600, 4800, 2400 and 1200 bit/s, each time writing the two characters
from the table below and waiting 0.1 seconds.
The following table shows available speeds and the strings that select them:
.TS
center;
l l.
bit/s	string
9600	*q
4800	*p
2400	*o
1200	*n
.TE

The first byte of a data packet can be used to synchronization purposes.
.SS Microsoft protocol
The \fBMicrosoft\fP protocol uses 1 start bit, 7 data bits, no parity
and one stop bit at the speed of 1200 bits/sec.
Data is sent to RxD in 3-byte packets.
The \fIdx\fP and \fIdy\fP movements are sent as
two's-complement, \fIlb\fP (\fIrb\fP) are set when the left (right)
button is pressed:
.TS
center;
r c c c c c c c.
byte	d6	d5	d4	d3	d2	d1	d0
1	1	lb	rb	dy7	dy6	dx7	dx6
2	0	dx5	dx4	dx3	dx2	dx1	dx0
3	0	dy5	dy4	dy3	dy2	dy1	dy0
.TE
.SS 3-button Microsoft protocol
Original Microsoft mice only have two buttons.
However, there are some
three button mice which also use the Microsoft protocol.
Pressing or
releasing the middle button is reported by sending a packet with zero
movement and no buttons pressed.
(Thus, unlike for the other two buttons, the status of the middle
button is not reported in each packet.)
.SS Logitech protocol
Logitech serial 3-button mice use a different extension of the
Microsoft protocol: when the middle button is up, the above 3-byte
packet is sent.
When the middle button is down a 4-byte packet is
sent, where the 4th byte has value 0x20 (or at least has the 0x20
bit set).
In particular, a press of the middle button is reported
as 0,0,0,0x20 when no other buttons are down.
.SS Mousesystems protocol
The \fBMousesystems\fP protocol uses 1 start bit, 8 data bits, no parity
and two stop bits at the speed of 1200 bits/sec.
Data is sent to RxD in
5-byte packets.
\fIdx\fP is sent as the sum of the two two's-complement
values, \fIdy\fP is send as negated sum of the two two's-complement
values.
\fIlb\fP (\fImb\fP, \fIrb\fP) are cleared when the left (middle,
right) button is pressed:
.TS
center;
r c c c c c c c c.
byte	d7	d6	d5	d4	d3	d2	d1	d0
1	1	0	0	0	0	lb	mb	rb
2	0	dxa6	dxa5	dxa4	dxa3	dxa2	dxa1	dxa0
3	0	dya6	dya5	dya4	dya3	dya2	dya1	dya0
4	0	dxb6	dxb5	dxb4	dxb3	dxb2	dxb1	dxb0
5	0	dyb6	dyb5	dyb4	dyb3	dyb2	dyb1	dyb0
.TE

Bytes 4 and 5 describe the change that occurred since bytes 2 and 3
were transmitted.
.SS Sun protocol
The \fBSun\fP protocol is the 3-byte version of the above 5-byte
Mousesystems protocol: the last two bytes are not sent.
.SS MM protocol
The \fBMM\fP protocol uses 1 start bit, 8 data bits, odd parity and one
stop bit at the speed of 1200 bits/sec.
Data is sent to RxD in 3-byte
packets.
\fIdx\fP and \fIdy\fP are sent as single signed values, the
sign bit indicating a negative value.
\fIlb\fP (\fImb\fP, \fIrb\fP) are
set when the left (middle, right) button is pressed:
.TS
center;
r c c c c c c c c.
byte	d7	d6	d5	d4	d3	d2	d1	d0
1	1	0	0	dxs	dys	lb	mb	rb
2	0	dx6	dx5	dx4	dx3	dx2	dx1	dx0
3	0	dy6	dy5	dy4	dy3	dy2	dy1	dy0
.TE
.SH FILES
.TP
.I /dev/mouse
A commonly used symlink pointing to a mouse device.
.SH SEE ALSO
.BR ttyS (4),
.BR gpm (8)