diff options
Diffstat (limited to 'src/libXNVCtrl/NVCtrl.h')
| -rw-r--r-- | src/libXNVCtrl/NVCtrl.h | 1408 |
1 files changed, 168 insertions, 1240 deletions
diff --git a/src/libXNVCtrl/NVCtrl.h b/src/libXNVCtrl/NVCtrl.h index 8f1289a..79af282 100644 --- a/src/libXNVCtrl/NVCtrl.h +++ b/src/libXNVCtrl/NVCtrl.h @@ -1357,1205 +1357,6 @@ #define NV_CTRL_GPU_OPTIMAL_CLOCK_FREQS_DETECTION_STATE_BUSY 1 - -/************************************************************************* - * DDC/CI VCP codes * - * From the VESA Monitor Control Command Set (MCCS) Standard - Version 2 * - *************************************************************************/ - -#define NV_CTRL_DDCCI_ON 1 -#define NV_CTRL_DDCCI_OFF 0 - -/************************************* - * DDC/CI VCP CODES: GEOMETRY ADJUST * - *************************************/ - -/* Increasing (decreasing) this value moves the image toward the right - * (left) side of the screen. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_POSITION 97 /* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the width - * of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_SIZE 98 /* RWD */ - -/* Increasing (decreasing) this value will cause the right and left sides - * of the image to become more (less) convex. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_PINCUSHION 99 /* RWD */ - -/* Increasing (decreasing) this value will move the center section of the - * image towards the right(left) side of the display. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_PINCUSHION_BALANCE 100/* RWD */ - -/* Increasing (decreasing) this value will shift the red pixels to the right - * (left) across the image and the blue pixels left (right) across the image - * with respect to the green pixels. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_CONVERGENCE 101/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * density of pixels in the image center. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_LINEARITY 102/* RWD */ - -/* Increasing (decreasing) this value shifts the density of pixels from - * the left (right) side to the right (left) side of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_LINEARITY_BALANCE 103/* RWD */ - -/* Increasing (decreasing) this value moves the image toward the - * top (bottom) edge of the display. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_POSITION 104/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * height of the image - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_SIZE 105/* RWD */ - -/* Increasing (decreasing) this value will cause the top and bottom - * edges of the image to become more (less) convex. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_PINCUSHION 106/* RWD */ - -/* Increasing (decreasing) this value will move the center section of - * the image toward the top (bottom) edge of the display. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_PINCUSHION_BALANCE 107/* RWD */ - -/* Increasing (decreasing) this value shifts the red pixels up (down) - * across the image and the blue pixels down (up) across the image - * with respect to the green pixels. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_CONVERGENCE 108/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * density of scan lines in the image center. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_LINEARITY 109/* RWD */ - -/* Increasing (decreasing) this value shifts the density of scan lines - * from the top (bottom) end to the bottom (top) end of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_LINEARITY_BALANCE 110/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * degree of keystone distortion in the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_KEYSTONE 111/* RWD */ - -/* Increasing (decreasing) this value shifts the top section of the - * image to the right (left) with respect to the bottom section of the - * image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_KEY_BALANCE 112/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * degree of trapezoid distortion in the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_TRAPEZOID 113/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * ratio between the horizontal size at the top of the image and the - * horizontal size at the bottom of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_TRAPEZOID 114/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * ratio between the vertical size at the left of the image and the - * vertical size at the right of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_VERTICAL_TRAPEZOID 115/* RWD */ - -/* Increasing (decreasing) this value rotates the image (counter) - clockwise about the center point of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_TILT 116/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * distance between the left and right sides at the top of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_TOP_CORNER 117/* RWD */ - -/* Increasing (decreasing) this value moves the top end of the - * image to the right (left). - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_TOP_CORNER_BALANCE 118/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * distance between the left and right sides at the bottom of the - * image. - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_BOTTOM_CORNER 119/* RWD */ - -/* Increasing (decreasing) this value moves the bottom end of the - * image to the right (left). - * Type: Range - */ -#define NV_CTRL_DDCCI_GEOMETRY_BOTTOM_CORNER_BALANCE 120/* RWD */ - - -/************************************** - * DDC/CI VCP CODES: PRESET SELECTION * - **************************************/ - -/* Restore all factory presets including brightness / contrast, - * geometry, color and TV defaults. - * NV__CTRL_DDCCI_ON causes defaults to be restored - * A value of NV_CTRL_DDCCI_OFF shall be ignored - * Type: Boolean - */ -#define NV_CTRL_DDCCI_PRESET_RESTORE_DEFAULTS 121/* -WD */ - -/* Restores factory defaults for brightness and contrast adjustments. - * NV_CTRL_DDCCI_ON causes defaults to be restored - * A value of NV_CTRL_DDCCI_OFF shall be ignored - * Type: Boolean - */ -#define NV_CTRL_DDCCI_PRESET_RESTORE_DEFAULTS_BRIGHTNESS_CONTRAST 122/* -WD */ - -/* Restore factory defaults for geometry adjustments. - * NV_CTRL_DDCCI_ON causes defaults to be restored - * A value of NV_CTRL_DDCCI_OFF shall be ignored - * Type: Boolean - */ -#define NV_CTRL_DDCCI_PRESET_RESTORE_DEFAULTS_GEOMETRY 123/* -WD */ - -/* Restore factory defaults for color settings. - * NV_CTRL_DDCCI_ON causes defaults to be restored - * A value of NV_CTRL_DDCCI_OFF shall be ignored - * Type: Boolean - */ -#define NV_CTRL_DDCCI_PRESET_RESTORE_DEFAULTS_COLOR 124/* -WD */ - -/* Restore factory defaults for TV functions. - * NV_CTRL_DDCCI_ON causes defaults to be restored - * A value of NV_CTRL_DDCCI_OFF shall be ignored - * Type: Boolean - */ -#define NV_CTRL_DDCCI_PRESET_RESTORE_DEFAULTS_TV 125/* -WD */ - -/* Store / Restore the user saved values for current mode. - * - NV_CTRL_DDCCI_PRESET_SETTINGS_STORE_CURRENT: - * Store current settings in the monitor. - * - NV_CTRL_DDCCI_PRESET_SETTINGS_RESTORE_FACTORY_DEFAULTS: - * Restore factory defaults for current mode. If no factory - * defaults then restore user values for current mode. - * - All other values are reserved and shall be ignored. - * Type: Integer - */ -#define NV_CTRL_DDCCI_PRESET_SETTINGS 126/* -WD */ -#define NV_CTRL_DDCCI_PRESET_SETTINGS_STORE_CURRENT 1 -#define NV_CTRL_DDCCI_PRESET_SETTINGS_RESTORE_FACTORY_DEFAULTS 2 - - -/*************************************** - * DDC/CI VCP CODES: IMAGE ADJUSTMENTS * - ***************************************/ - -/* - * Increasing (decreasing) this value will increase (decrease) the - * Brightness of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_BRIGHTNESS 127/* RWD */ - -/* - * Increasing (decreasing) this value will increase (decrease) the - * Contrast of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_CONTRAST 128/* RWD */ - -/* - * Turn on / off an auto setup function (periodic or event driven) - * 0 and 3 : Shall be ignored - * NV_CTRL_DDCCI_IMAGE_AUTO_SETUP_TOGGLE_OFF : Turn auto setup off - * NV_CTRL_DDCCI_IMAGE_AUTO_SETUP_TOGGLE_ON : Turn auto setup on - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_AUTO_SETUP_TOGGLE 129/* -WD */ -#define NV_CTRL_DDCCI_IMAGE_AUTO_SETUP_TOGGLE_OFF 1 -#define NV_CTRL_DDCCI_IMAGE_AUTO_SETUP_TOGGLE_ON 2 - -/* - * Perform autosetup function (H/V position, clock, clock phase, A/D - * converter, etc) - * NV_CTRL_OFF : Indicates that auto-setup is not active - * NV_CTRL_ON : Perform autosetup - * >=2 : Shall be ignored - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_AUTO_SETUP 130/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * sampling clock frequency - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_CLOCK 131/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * phase shift of the sampling clock - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_CLOCK_PHASE 132/* RWD */ - -/* Allows the display to specify the minimum increment in which it - * can adjust the color temperature. - * This will be used in conjunction with - * NV_CTRL_DDCCI_IMAGE_COLOR_TEMPERATURE_REQUEST, Color temperature request. - * Values of 0 and > 5000 are invalid and shall be ignored. - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_COLOR_TEMPERATURE_INCREMENT 133/* R-D */ - -/* Allows a specified color temperature (in °K) to be requested. If - * display is unable to achieve requested color temperature, then it - * should move to the closest possible temperature. - * A value of 0 shall be treated as a request for a color temperature - * of 3000°K. Values greater than 0 shall be used as a multiplier of - * the color temperature increment (read using - * NV_CTRL_DDCCI_IMAGE_COLOR_TEMPERATURE_INCREMENT) and the - * result added to the base value of 3000°K - * Example: - * If NV_CTRL_DDCCI_IMAGE_COLOR_TEMPERATURE_INCREMENT returns a value of - * 50°K and NV_CTRL_DDCCI_IMAGE_COLOR_TEMPERATURE_INCREMENT sends a - * value of 50 (decimal) then the display shall interpret this as a - * request to adjust the color temperature to 5500°K - * (3000 + (50 * 50))°K = 5500°K - * Notes: - * 1) Applications using this function are recommended to read the - * actual color temperature after using this command and taking - * appropriate action. - * 2) This control is only recommended if the display can produce a - * continuously (at defined increment, see VCP code 0Bh) variable - * color temperature. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_COLOR_TEMPERATURE_REQUEST 134/* RWD */ - -/* Select a specified color temperature. - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_SRGB : sRGB - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_NATIVE : Display native - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_4000K : 4000 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_5000K : 5000 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_6500K : 6500 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_7500K : 7500 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_8200K : 8200 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_9300K : 9300 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_10000K : 10000 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_USER1 : 11500 K - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_USER1 : User 1 - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_USER2 : User 2 - * NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_USER3 : User 3 - * 00 and >=0E shall be ignored - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET 135/* RWD */ -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_SRGB 0x01 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_NATIVE 0x02 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_4000K 0x03 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_5000K 0x04 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_6500K 0x05 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_7500K 0x06 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_8200K 0x07 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_9300K 0x08 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_10000K 0x09 -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_11500K 0x0A -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_USER1 0x0B -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_USER2 0x0C -#define NV_CTRL_DDCCI_IMAGE_SELECT_COLOR_PRESET_USER3 0x0D - -/* - * Increasing (decreasing) this value will increase (decrease) the - * luminance of red pixels. - * The value returned shall be an indication of the actual red gain at - * the current color temperature and not be normalized. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_RED_VIDEO_GAIN 136/* RWD */ - -/* - * Increasing (decreasing) this value will increase (decrease) the - * luminance of green pixels. - * The value returned shall be an indication of the actual green gain at - * the current color temperature and not be normalized. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_GREEN_VIDEO_GAIN 137/* RWD */ - -/* - * Increasing (decreasing) this value will increase (decrease) the - * luminance of blue pixels. - * The value returned shall be an indication of the actual blue gain at - * the current color temperature and not be normalized. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_BLUE_VIDEO_GAIN 138/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * black level of red pixels. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_RED_VIDEO_BLACK_LEVEL 139/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * black level of green pixels. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_GREEN_VIDEO_BLACK_LEVEL 140/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * black level of blue pixels. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_BLUE_VIDEO_BLACK_LEVEL 141/* RWD */ - -/* Increasing (decreasing) this value will adjust the focus of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_FOCUS 142/* RWD */ - -/* Increasing (decreasing) this value controls the horizontal picture - * moiré cancellation. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_HORIZONTAL_MOIRE 143/* RWD */ - -/* Increasing (decreasing) this value controls the vertical picture - * moiré cancellation. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_VERTICAL_MOIRE 144/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * distance to the focal plane of the image. - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_ADJUST_FOCAL_PLANE 145/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * zoom function of the optics - * Type: Range - */ -#define NV_CTRL_DDCCI_IMAGE_ADJUST_ZOOM 146/* RWD */ - -/* This value will cause the picture to flip horizontally. - * NV_CTRL_DDCCI_ON : flip horizontally - * NV_CTRL_DDCCI_OFF : Shall be ignored - * Type: Boolean - */ -#define NV_CTRL_DDCCI_IMAGE_HOR_FLIP 147/* -WD */ - -/* This value will cause the picture to flip vertically. - * NV_CTRL_DDCCI_ON : flip vertically - * NV_CTRL_DDCCI_OFF : Shall be ignored - * Type: Boolean - */ -#define NV_CTRL_DDCCI_IMAGE_VER_FLIP 148/* -WD */ - -/* Changing this value will affect the scaling (input versus output) - * function of the display. - * NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_NO_SCALING : No scaling, 1:1 relationship - * NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_MAX_NO_DISTORT2 : Scale to maximum - * without AR distortion - * NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_MAX_VERTICAL : Scale to maximum vertical - size - * NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_MAX_HORIZONTAL ; Scale to maximum - horizontal size - * 0 and >=5 : Shall be ignored - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING 149/* RWD */ -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_NO_SCALING 1 -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_MAX_NO_DISTORT 2 -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_MAX_VERTICAL 3 -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_SCALING_MAX_HORIZONTAL 4 - -/* Allows one of several image expansion algorithms to be selecte - * to suit different types of image and/or different personal - * preference. - * NV_CTRL_DDCCI_IMAGE_SHARPNESS_FILTER_FUNC(1) : Filter function 1 - * NV_CTRL_DDCCI_IMAGE_SHARPNESS_FILTER_FUNC(2) : Filter function 2 - * NV_CTRL_DDCCI_IMAGE_SHARPNESS_FILTER_FUNC(3) : Filter function 3 - * NV_CTRL_DDCCI_IMAGE_SHARPNESS_FILTER_FUNC(4) : Filter function 4 - * 0 and 5 shall be ignored - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_SHARPNESS 150/* RWD */ -#define NV_CTRL_DDCCI_IMAGE_SHARPNESS_FILTER_FUNC(n) n - -/* Indicates the orientation of the screen. - * NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_0 - * The normal landscape mode. - * NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_90 - * Portrait mode achieved by clockwise rotation of the display 90 degrees. - * NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_180 - * Landscape mode achieved by rotation of the display 180 degrees. - * NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_270 - * Portrait mode achieved by clockwise rotation of the display 270 degrees. - * NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_NA - * Indicates that the display cannot supply the current orientation - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION 151/* R-D */ -#define NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_0 0x01 -#define NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_90 0x02 -#define NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_180 0x03 -#define NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_270 0x04 -#define NV_CTRL_DDCCI_IMAGE_SCREEN_ORIENTATION_NA 0xFF - -/* Selects a scan format. - * NV_CTRL_DDCCI_IMAGE_SCAN_FORMAT_UNDERSCAN: Underscan - * NV_CTRL_DDCCI_IMAGE_SCAN_FORMAT_OVERSCAN: Overscan - * NV_CTRL_DDCCI_IMAGE_SCAN_FORMAT_WIDESCREEN: Widescreen - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_SCAN_FORMAT 152/* RWD */ -#define NV_CTRL_DDCCI_IMAGE_SCAN_FORMAT_UNDERSCAN 1 -#define NV_CTRL_DDCCI_IMAGE_SCAN_FORMAT_OVERSCAN 2 -#define NV_CTRL_DDCCI_IMAGE_SCAN_FORMAT_WIDESCREEN 3 -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE 153/* RWD */ - -/* Display mode: - * NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_PRODUCTIVITY : - * Productivity (e.g. office applications) - * NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_MIXED : Mixed (e.g. internet) - * NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_ENTERTAINMENT : - Entertainment (e.g. TV / movie) - * NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_USERDEFINED : User defined - * Note: - * The condition(s) associated with options 1, 2 and 3 are defined - * by the display manufacturer - * Type: Integer - */ -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_PRODUCTIVITY 1 -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_MIXED 2 -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_ENTERTAINMENT 3 -#define NV_CTRL_DDCCI_IMAGE_DISPLAY_MODE_USERDEFINED 4 - -/*********************************************** - * DDC/CI VCP CODES: WINDOWED IMAGE OPERATIONS * - ***********************************************/ - -/* Defines the top left X pixel of an area of the image. Specified in - * co-ordinates of incoming image before any scaling etc in the display. - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_POSITION_TOP_LEFT_X 154/* RWD */ - -/* Defines the top left Y pixel of an area of the image. Specified in - * co-ordinates of incoming image before any scaling etc in the display. - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_POSITION_TOP_LEFT_Y 155/* RWD */ - -/* Defines the bottom right X pixel of an area of the image. - * Specified in co-ordinates of incoming image before any scaling - * in the display. - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_POSITION_BOTTOM_RIGHT_X 156/* RWD */ - -/* Defines the bottom right Y pixel of an area of the image. - * Specified in co-ordinates of incoming image before any scaling - * in the display. - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_POSITION_BOTTOM_LEFT_X 157/* RWD */ - -/* Window control, enables the brightness and color within a - * window to be different from the desktop. - * NV_CTRL_DDCCI_WINDOWEDIMAGE_OLD_CONTROL_TOGGLE_OFF : Off - * NV_CTRL_DDCCI_WINDOWEDIMAGE_OLD_CONTROL_TOGGLE_ON: On - * All other values are reserved. - * Notes: - * 1. This control should be used in conjunction with - * NV_CTRL_DDCCI_WINDOWEDIMAGE_BACKGROUND - * 2. This command structure is not recommended for new designs, - * see NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE for alternate. - * Type: Integer - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_OLD_CONTROL_TOGGLE 158/* RWD */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_OLD_CONTROL_TOGGLE_OFF 1 -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_OLD_CONTROL_TOGGLE_ON 2 - -/* Changes the contrast ratio between the area of the window and - * the rest of the desktop - * Lower (higher) values will cause the desktop brightness to - * decrease (increase) - * Notes: - * 1. This contropl should be used in conjunction with - * NV_CTRL_DDCCI_WINDOWEDIMAGE_OLD_CONTROL_TOGGLE - * 2. This command structure is not recommended for new designs, - * see NV_CTRL_DDCCI_WINDOWEDIMAGE_WINDOW_SELECT for alternate. - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_BACKGROUND 159/* RWD */ - -/* A value of 127 shall have no effect. - * A value > 127 shall cause the color to shift towards yellow - * A value < 127 shall cause the color to shift towards magenta - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_6AXIS_COLOR_CONTROL_RED 160/* RWD */ - -/* A value of 127 shall have no effect. - * A value > 127 shall cause the color to shift towards green - * A value < 127 shall cause the color to shift towards red - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_6AXIS_COLOR_CONTROL_YELLOW 161/* RWD */ - -/* A value of 127 shall have no effect. - * A value > 127 shall cause the color to shift towards cyan - * A value < 127 shall cause the color to shift towards yellow - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_6AXIS_COLOR_CONTROL_GREEN 162/* RWD */ - -/* A value of 127 shall have no effect. - * A value > 127 shall cause the color to shift towards blue - * A value < 127 shall cause the color to shift towards green - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_6AXIS_COLOR_CONTROL_CYAN 163/* RWD */ - -/* A value of 127 shall have no effect. - * A value > 127 shall cause the color to shift towards magenta - * A value < 127 shall cause the color to shift towards cyan - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_6AXIS_COLOR_CONTROL_BLUE 164/* RWD */ - -/* A value of 127 shall have no effect. - * A value > 127 shall cause the color to shift towards red - * A value < 127 shall cause the color to shift towards blue - * Type: Range - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_6AXIS_COLOR_CONTROL_MAGENTA 165/* RWD */ - -/* Turn the selected window operation on / off. - * Bit: NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE_DPY_IMAGE - * 0 Window controls have no effect on the - * displayed image - * 1 Window controls effect the displayed image - * (full image area) - * Bit: NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE_WINDOW(n) - * 0 Window controls have no effect on the - * displayed image (window n) - * 1 Window controls effect the displayed image - * (window n) - * n is between 1 and 7 - * Note: This command structure is recommend, in conjunction with - * NV_CTRL_DDCCI_WINDOWEDIMAGE_WINDOW_SELECT, for all new designs. - * Type: Bitmask - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE 166/* RWD */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE_DPY_IMAGE 1 -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE_WINDOW(n) (1<<n) - -/* Change the selected window as defined with - * NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE - * When a window is selected then all commands that the display - * controller supports for window operations are valid, this may - * include but is not limited to: brightness, contrast, R/G/B gain, 6- - * axis color, sharpness, etc. - * meaning of value NV_CTRL_DDCCI_WINDOWEDIMAGE_WINDOW_SELECT_DPY_IMAGE: - * Full display image area is selected except for - * area(s) of active windows - * meaning of value NV_CTRL_DDCCI_WINDOWEDIMAGE_WINDOW_SELECT_WINDOW(n) - * Window n is selected - * If this command is not supported then the `full image area' shall - * be the default. - * This command structure is recommend, in conjunction with - * NV_CTRL_DDCCI_WINDOWEDIMAGE_CONTROL_TOGGLE, for all new designs. - * Type: Integer - */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_WINDOW_SELECT 167/* RWD */ -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_WINDOW_SELECT_DPY_IMAGE 0 -#define NV_CTRL_DDCCI_WINDOWEDIMAGE_WINDOW_SELECT_WINDOW(n) (1<<n) - - -/*************************************/ -/* DDC/CI VCP CODES: AUDIO FUNCTIONS */ -/*************************************/ - -/* Increasing (decreasing) this value will increase (decrease) the - * audio volume. - * Type: Range - */ -#define NV_CTRL_DDCCI_AUDIO_SPEAKER_VOLUME 168/* RWD */ - -/* Increasing (decreasing) this value will increase (decrease) the - * microphone gain. - * Type: Range - */ -#define NV_CTRL_DDCCI_AUDIO_MICROPHONE_VOLUME 169/* RWD */ - -/* Increasing (decreasing) this control will cause high frequency - * audio to be emphasized (de-emphasised). - * Type: Range - */ -#define NV_CTRL_DDCCI_AUDIO_TV_AUDIO_TREBLE 170/* RWD */ - -/* Increasing (decreasing) this control will cause low frequency - * audio to be emphasized (de-emphasised). - * Type: Range - */ -#define NV_CTRL_DDCCI_AUDIO_TV_AUDIO_BASS 171/* RWD */ - -/* This control affects the left right balance of audio output. - * Increasing (decreasing) the value will cause the balance to move - * to the right (left). - * Type: Range - */ -#define NV_CTRL_DDCCI_AUDIO_TV_AUDIO_BALANCE 172/* RWD */ - -/* This control allows one of several audio modes to be selected. - * NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_OFF: Display audio is disabled, - * NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_MONO: Both display audio channels, - * use the left audio channel - * NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_STEREO: Incoming left and right - * audio. Channels feed separate display output audio channels. - * NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_STEREO_EXPANDED: As defined - * by the manufacturer. - * Type: Integer - */ -#define NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE 173/* RWD */ -#define NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_OFF 0 -#define NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_MONO 1 -#define NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_STEREO 2 -#define NV_CTRL_DDCCI_AUDIO_TV_STEREO_MODE_SPEAKER_STEREO_EXPANDED 3 - - -/************************************/ -/* DDC/CI VCP CODES: DPVL Functions */ -/************************************/ - -/* Video mode and status of a DPVL capable monitor - * Bit Value Meaning - * 0 0 Raster scan mode - * 1 DPVL mode - * 1 0 Monitor is able to receive the next packet - * 1 Monitor is unable to accept another packet - * 2 0 No error detected in the last header received - * 1 Error detected in the last header received - * Other bits are reserved and shall be set to '0'. - * Type: Bitmask - */ -#define NV_CTRL_DDCCI_DPVL_MONITOR_STATUS 174/* R-D */ -#define NV_CTRL_DDCCI_DPVL_MONITOR_STATUS_DPVL_MODE (1<<0) -#define NV_CTRL_DDCCI_DPVL_MONITOR_STATUS_UNABLE_TO_RECEIVE_NEXT_PACKET (1<<1) -#define NV_CTRL_DDCCI_DPVL_MONITOR_STATUS_ERROR_DETECTED_IN_LAST_HEADER (1<<2) - -/* Counter for the DPVL packets received (valid and invalid ones). - * This value counts from 0000h to FFFFh and then rolls over to 0000h. - * The host can reset the value to 0000h. - * Type: Range - */ -#define NV_CTRL_DDCCI_DPVL_PACKET_COUNT 175/* RWD */ - -/* The X origin of the monitor in the virtual screen. The support of - * this command indicates the multi-display support of the display. If - * a display supports this command, the monitor must also support - * Monitor Y Origin command. - * Type: Range; "0000h" to "FFFFh" or 0 to 65535 - */ -#define NV_CTRL_DDCCI_DPVL_MONITOR_X_ORIGIN 176/* RWD */ - -/* The Y origin of the display in the virtual screen. The support of - * this command indicates the multi-display support of the display. If - * a display supports this command, the monitor must also support - * Monitor X Origin command. - * Type: Range; "0000h" to "FFFFh" or 0 to 65535 - */ -#define NV_CTRL_DDCCI_DPVL_MONITOR_Y_ORIGIN 177/* RWD */ - -/* Error Counter for the DPVL header. The counter value saturates - * at FFFFh. Host can reset to 0000h. - * Type: Range - */ -#define NV_CTRL_DDCCI_DPVL_HEADER_ERROR_COUNT 178/* RWD */ - -/* CRC error Counter for the DPVL body (containing video data). - * The counter value saturates at FFFFh. The Host can reset to 0000h - * Type: Range - */ -#define NV_CTRL_DDCCI_DPVL_BODY_CRC_ERROR_COUNT 179/* RWD */ - -/* Assigned identification number for the monitor. - * Type: Valid range is 0000h to FFFEh, FFFFh is reserved for broadcast. - */ -#define NV_CTRL_DDCCI_DPVL_CLIENT_ID 180/* RWD */ - -/* Indicates the status of the DVI link - * NV_CTRL_DDCCI_DPVL_LINK_CONTROL_DISABLED: Link shutdown is disabled - * NV_CTRL_DDCCI_DPVL_LINK_CONTROL_ENABLED: Link shutdown is enabled - * Type: Boolean - */ -#define NV_CTRL_DDCCI_DPVL_LINK_CONTROL 181/* RWD */ -#define NV_CTRL_DDCCI_DPVL_LINK_CONTROL_DISABLED 0 -#define NV_CTRL_DDCCI_DPVL_LINK_CONTROL_ENABLED 1 - -/**********************************************/ -/* DDC/CI VCP CODES: Miscellaneous Functions */ -/**********************************************/ - -/* Causes a CRT display to perform a degauss cycle with - * NV_CTRL_DDCCI_ON - * Type: Boolean - */ -#define NV_CTRL_DDCCI_MISC_DEGAUSS 182/* -WD */ - -/* Used to indicate that a display user control (excluding power - * controls) has been used to change and save (or autosave) a new value. - * NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NO_NEW : No new control value - * NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NO_USER_CONTROLS : A new control value - * has been saved - * NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NO_USER_CONTROLS : No user controls are present - * Note: - * A value = NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NEW should only be reset to - * a value = NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NO_NEW by a host write - * operation and not by the display - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE 183/* RWD */ -#define NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NO_NEW 0x01 -#define NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NEW 0x02 -#define NV_CTRL_DDCCI_MISC_NEW_CONTROL_VALUE_NO_USER_CONTROLS 0xFF - -/* Allows display controls to be used as soft keys - * NV_CTRL_DDCCI_MISC_SOFT_CONTROLS_NO_BUTTON_ACTIVE : No button active - * NV_CTRL_DDCCI_MISC_SOFT_CONTROLS_BUTTON(n): Button n active - * n is between 1 and 7. - * NV_CTRL_DDCCI_MISC_SOFT_CONTROLS_NONE : No controls present - * Note: - * A `button active' value should only be reset to a value = 0 by - * host write operation and not by the display - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_SOFT_CONTROLS 184/* RWD */ -#define NV_CTRL_DDCCI_MISC_SOFT_CONTROLS_NO_BUTTON_ACTIVE 0 -#define NV_CTRL_DDCCI_MISC_SOFT_CONTROLS_BUTTON(n) n -#define NV_CTRL_DDCCI_MISC_SOFT_CONTROLS_NONE 0xFF - -/* When read this control returns the VCP code associated with - * the new control value reported using 02H - * Examples: - * If brightness has been changed then return value of 10h - * If red gain has been changed then return value of 16h. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_ACTIVE_CONTROL 185/* R-D */ - -/* Used to select the active video source - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_ANALOG_1: Analog video (R/G/B) 1 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_ANALOG_2: Analog video (R/G/B) 2 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_DIGITAL_1: Digital video (TMDS) 1 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_DIGITAL_2: Digital video (TMDS) 2 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPOSITE_1: Composite video 1 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPOSITE_2: Composite video 2 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_SVIDEO_1: S-video 1 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_SVIDEO_2: S-video 2 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_TUNER_1: Tuner 1 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_TUNER_2: Tuner 2 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_TUNER_3: Tuner 3 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPONENT_1: Component video (YPrPb/YCrCb) 1 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPONENT_2: Component video (YPrPb/YCrCb) 2 - * NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPONENT_3: Component video (YPrPb/YCrCb) 3 - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE 186/* RWD */ -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_ANALOG_1 1 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_ANALOG_2 2 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_DIGITAL_1 3 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_DIGITAL_2 4 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPOSITE_1 5 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPOSITE_2 6 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_SVIDEO_1 7 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_SVIDEO_2 8 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_TUNER_1 9 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_TUNER_2 10 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_TUNER_3 11 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPONENT_1 12 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPONENT_2 13 -#define NV_CTRL_DDCCI_MISC_INPUT_SOURCE_COMPONENT_3 14 - -/* ncreasing (decreasing) this value will increase (decrease) the - * velocity modulation of the horizontal scan as a function of a - * change in the luminance level. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_VELOCITY_SCAN_MODULATION 187/* RWD */ - -/* Increasing this control increases the amplitude of the color - * difference components of the video signal. - * The result is an increase in the amount of pure color relative to - * white in the video. This control does not affect the RGB input, - * only the TV video inputs. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_TV_COLOR_SATURATION 188/* RWD */ - -/* Used to increment / decrement between TV-channels, the exact - * behavior is implementation specific (e.g. increment / decrement - * to next numeric channel or increment / decrement to next - * channel with a signal) - * NV_CTRL_DDCCI_MISC_TV_CHANNEL_UP_DOWN_INCREMENT: Increment channel - * NV_CTRL_DDCCI_MISC_TV_CHANNEL_UP_DOWN_DECREMENT: Decrement channel - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_TV_CHANNEL_UP_DOWN 189/* -WD */ -#define NV_CTRL_DDCCI_MISC_TV_CHANNEL_UP_DOWN_INCREMENT 1 -#define NV_CTRL_DDCCI_MISC_TV_CHANNEL_UP_DOWN_DECREMENT 2 - -/* Increasing this control increases the amplitude of the high - * frequency components of the video signal. - * This allows fine details to be accentuated. This control does not - * affect the RGB input, only the TV video inputs. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_TV_SHARPNESS 190/* RWD */ - -/* Provides for the TV-audio to be muted or unmated. - * NV_CTRL_DDCCI_MISC_TV_AUDIO_MUTE_ON: Mute the audio - * NV_CTRL_DDCCI_MISC_TV_AUDIO_MUTE_OFF: Unmute the audio - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_TV_AUDIO_MUTE 191/* RWD */ -#define NV_CTRL_DDCCI_MISC_TV_AUDIO_MUTE_ON 1 -#define NV_CTRL_DDCCI_MISC_TV_AUDIO_MUTE_OFF 2 - -/* Increasing (decreasing) this control increases (decreases) the - * ratio between whites and blacks in the video. - * This control does not affect the RGB input, only the TV video - * inputs. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_TV_CONTRAST 192/* RWD */ - -/* Also known as `tint' - * Increasing (decreasing) this control increases (decreases) the - * wavelength of the color component of the video signal. - * The result is a shift towards red (blue) in the hue of all colors. - * This control does not affect the RGB input, only the TV video - * inputs. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_TV_HUE 193/* RWD */ - -/* Increasing this control increases the black level of the video, - * resulting in an increase of the luminance level of the video. - * A value of zero represents the darkest level possible. - * This control does not affect the RGB input, only the TV video - * inputs. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_TV_BLACK_LEVEL_SHARPNESS 194/* RWD */ - -/* Horizontal synchronization signal frequency in Hz as determined - * by the display. - * FFh: Indicates that the display cannot supply this information - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_HORIZONTAL_FREQUENCY 195/* R-D */ - -/* Vertical synchronization signal frequency in 0.01Hz as - * determined by the display. - * FFh: Indicates that the display cannot supply this information - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_VERTICAL_FREQUENCY 196/* R-D */ - -/* Select a type of LCD sub-pixel structure - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_UNDEFINED: - * Sub-pixel layout is not defined - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_RGB_V: - * Red / Green / Blue vertical stripe - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_RGB_H: - * Red / Green / Blue horizontal stripe - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_BGR_V: - * Blue / Green / Red vertical stripe - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_BGR_H: - * Blue/ Green / Red horizontal stripe - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_QUAD_1: - * Quad-pixel, a 2 x 2 sub-pixel structure with red at top - * left, blue at bottom right and green at top right and - * bottom left - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_QUAD_2: - * Quad-pixel, a 2 x 2 sub-pixel structure with red at - * bottom left, blue at top right and green at top left and - * bottom right - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_DELTA: - * Delta (triad) - * NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_MOSAIC: - * Mosaic with red, green and blue fields overlayed - * (field sequential color) - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT 197/* R-D */ -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_UNDEFINED 0 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_RGB_V 1 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_RGB_H 2 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_BGR_V 3 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_BGR_H 4 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_QUAD_1 5 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_QUAD_2 6 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_DELTA 7 -#define NV_CTRL_DDCCI_MISC_FLATPANEL_SUBPIXEL_LAYOUT_MOSAIC 8 - -/* Select the base technology type - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_CRT_SHADOWMASK: CRT (shadowmask) - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_CRT_APERTURE_GRILL: CRT (aperture - * grill) - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_TFT: TFT - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_LCOS: LCoS - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_PLASMA: Plasma - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_OLED: OLED - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_EL: EL - * NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_MEM: MEM - * Type: integer - */ -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE 198/* R-D */ -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_CRT_SHADOWMASK 1 -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_CRT_APERTURE_GRILL 2 -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_TFT 3 -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_LCOS 4 -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_PLASMA 5 -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_OLED 6 -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_EL 7 -#define NV_CTRL_DDCCI_MISC_DISPLAY_TECHNOLOGY_TYPE_MEM 8 - -/* Returns the current value (in hours) of `active power on' time - * accumulated by the display a 2 byte value. - * "Active power on" time is defined as the period when the - * emissive elements(s) of the display cathodes for a CRT, - * fluorescent lamps for a LCD, etc are active. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_DISPLAY_USAGE_TIME 199/* R-D */ - -/* Returns the length (in bytes) of non-volatile storage in the display - * available for writing a display descriptor the maximum - * descriptor length is 256 bytes - * See - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_DISPLAY_DESCRIPTOR_LENGTH 200/* R-D */ - -/* If enabled (NV_CTRL_DDCCI_ON), the display descriptor written to the - * display using XNVCTRLSetDDCCIDisplayDescriptor() shall be displayed when - * no video is being received. - * The duration for which it is displayed is left to individual manufacturers. - * NV_CTRL_DDCCI_ON: Display is enabled - * NV_CTRL_DDCCI_OFF: The display descriptor shall not be displayed. - * Type: Boolean - */ -#define NV_CTRL_DDCCI_MISC_ENABLE_DISPLAY_OF_DISPLAY_DESCRIPTOR 201/* RWD */ - -/* A 2 byte value used to allow an application to only operate with - * known products. The display manufacturer and application author - * agree to a code such that application will only run when a valid - * code is present in the display. - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_APPLICATION_ENABLE_KEY 202/* R-D */ - -/* This VCP code provides allows a 2 byte value identifying the - * firmware level installed in the display to be determined. - * Type: Range - */ -#define NV_CTRL_DDCCI_MISC_DISPLAY_FIRMWARE_LEVEL 203/* R-D */ - -/* Indicates the current state of the display OSD - * NV_CTRL_DDCCI_MISC_OSD_DISABLED: OSD is disabled - * NV_CTRL_DDCCI_MISC_OSD_ENABLED: OSD is enabled - * NV_CTRL_DDCCI_MISC_OSD_CANNOT_SUPPLY: Indicates that the display cannot - * supply this information. - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_OSD 204/* RWD */ -#define NV_CTRL_DDCCI_MISC_OSD_DISABLED 1 -#define NV_CTRL_DDCCI_MISC_OSD_ENABLED 2 -#define NV_CTRL_DDCCI_MISC_OSD_CANNOT_SUPPLY 0xFF - -/* Allows the displayed OSD language to be selected. - * Type: Integer */ -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE 205/* RWD */ -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_CHINESE 1 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_ENGLISH 2 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_FRENCH 3 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_GERMAN 4 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_ITALIAN 5 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_JAPANESE 6 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_KOREAN 7 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_PORTUGESE 8 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_RUSSIAN 9 -#define NV_CTRL_DDCCI_MISC_OSD_LANGUAGE_SPANISH 10 - -/* An `auxiliary display' is a small alpha-numeric display associated - * with the primary display and able to be accessed via the primary - * display. - * This command returns a 1 byte value that defines the number of - * characters and the number of rows available. The format is: - * Bits 0 to 5 : The number of characters / row - * Bits 6 to 7 : The number of rows - * I.e. The maximum auxiliary display size is 4 rows each with 64 characters - * Type: Bitmask - */ -#define NV_CTRL_DDCCI_MISC_AUXILIARY_DISPLAY_SIZE 206/* R-D */ -#define NV_CTRL_DDCCI_MISC_AUXILIARY_DISPLAY_SIZE_COLUMNS_MASK 0x1F -#define NV_CTRL_DDCCI_MISC_AUXILIARY_DISPLAY_SIZE_ROWS_MASK 0x60 - -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT 207/* RWD */ - -/* Used to selects the active output. - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_ANALOG_1: Analog video (R/G/B) 1 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_ANALOG_2: Analog video (R/G/B) 2 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_DIGITAL_1: Digital video (TMDS) 1 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_DIGITAL_2: Digital video (TMDS) 2 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPOSITE_1: Composite video 1 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPOSITE_2: Composite video 2 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_SVIDEO_1: S-video 1 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_SVIDEO_2: S-video 2 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_TUNER_1: Tuner 1 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_TUNER_2: Tuner 2 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_TUNER_3: Tuner 3 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPONENT_1: Component video (YPrPb/YCrCb) 1 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPONENT_2: Component video (YPrPb/YCrCb) 2 - * NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPONENT_3: Component video (YPrPb/YCrCb) 3 - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_ANALOG_1 1 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_ANALOG_2 2 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_DIGITAL_1 3 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_DIGITAL_2 4 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPOSITE_1 5 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPOSITE_2 6 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_SVIDEO_1 7 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_SVIDEO_2 8 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_TUNER_1 9 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_TUNER_2 10 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_TUNER_3 11 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPONENT_1 12 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPONENT_2 13 -#define NV_CTRL_DDCCI_MISC_OUTPUT_SELECT_COMPONENT_3 14 - -/* Used to select the video mode with respect to 2D or 3D video. - * Here is the meaning of the bitmask: - * NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_FIELD_SEQUENTIAL_RIGHT_FIRST: - * Enable Field-Sequential Right Eye First - * NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_FIELD_SEQUENTIAL_LEFT_FIRST: - * Enable Field-Sequential Left Eye First - * NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_2WAY_INTERLEAVED_RIGHT_FIRST: - * Enable 2-Way Interleaved Right Eye First - * NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_2WAY_INTERLEAVED_LEFT_FIRST: - * Enable 2-Way Interleaved Left Eye First - * NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_4WAY_INTERLEAVED_ODD_LINES: - * Enable 4-Way Interleaved, Display Stereo Buffer 0 (even scan lines) - * NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_4WAY_INTERLEAVED_ODD_LINES: - * Enable 4-Way Interleaved, Display Stereo Buffer 1 (odd scan lines) - * NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_SIDE_BY_SIDE_INTERLEAVED: - * Enable Side-by-Side Interleaved - * Note: It is permissible, during a read operation, for a display to indicate - * support for 2 or more stereo modes - * Type: Bitmask - */ -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE 208/* RWD */ -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_FIELD_SEQUENTIAL_RIGHT_FIRST (1<<6) -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_FIELD_SEQUENTIAL_LEFT_FIRST (1<<5) -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_2WAY_INTERLEAVED_RIGHT_FIRST (1<<4) -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_2WAY_INTERLEAVED_LEFT_FIRST (1<<3) -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_4WAY_INTERLEAVED_EVEN_LINES (1<<2) -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_4WAY_INTERLEAVED_ODD_LINES (1<<1) -#define NV_CTRL_DDCCI_MISC_STEREO_VIDEO_MODE_SIDE_BY_SIDE_INTERLEAVED (1<<0) - -/* Power Mode DPMS and DPM standards are supported. - * Value DPMS DPM - * NV_CTRL_DDCCI_MISC_POWER_MODE_ON On On - * NV_CTRL_DDCCI_MISC_POWER_MODE_STANDBY Standby Off - * NV_CTRL_DDCCI_MISC_POWER_MODE_SUSPEND Suspend Off - * NV_CTRL_DDCCI_MISC_POWER_MODE_OFF Off Off - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_POWER_MODE 209/* RWD */ -#define NV_CTRL_DDCCI_MISC_POWER_MODE_ON 1 -#define NV_CTRL_DDCCI_MISC_POWER_MODE_STANDBY 2 -#define NV_CTRL_DDCCI_MISC_POWER_MODE_SUSPEND 3 -#define NV_CTRL_DDCCI_MISC_POWER_MODE_OFF 4 - -/* Controls output of an auxiliary power output from a display to a host device. - * NV_CTRL_DDCCI_MISC_AUXILIARY_POWER_OUTPUT_DISABLE: - * Disable auxiliary output power - * NV_CTRL_DDCCI_MISC_AUXILIARY_POWER_OUTPUT_ENABLE: - * Enable auxiliary output power - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_AUXILIARY_POWER_OUTPUT 210/* RWD */ -#define NV_CTRL_DDCCI_MISC_AUXILIARY_POWER_OUTPUT_DISABLE 1 -#define NV_CTRL_DDCCI_MISC_AUXILIARY_POWER_OUTPUT_ENABLE 2 - -/* Operation mode - * NV_CTRL_DDCCI_MISC_OPERATION_MODE_STANDALONE: Stand alone - * NV_CTRL_DDCCI_MISC_OPERATION_MODE_SLAVE: Slave (full PC control) - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_OPERATION_MODE 211/* -WD */ -#define NV_CTRL_DDCCI_MISC_OPERATION_MODE_STANDALONE 1 -#define NV_CTRL_DDCCI_MISC_OPERATION_MODE_SLAVE 2 - -/* Define the version number of VCP list recognized by the display. - * This is a 2 byte value, byte 1 defines the version number and - * byte 2 defines the revision number - * e.g 02 00 (hex) defines Version 2, Revision 0 - * Type: Integer - */ -#define NV_CTRL_DDCCI_MISC_VCP_VERSION 212/* R-D */ - -/* Save the current adjustment data to EEPROM or other - * non-volatile storage inside the display - * Returns TRUE on success - * Type: Boolean - */ -#define NV_CTRL_DDCCI_SAVE_CURRENT_SETTINGS 213/* -WD */ - -/* Detects if the display is DDC/CI capable - * Returns TRUE on success - * Type: Boolean - */ -#define NV_CTRL_DDCCI_CAPABLE 214/* R-D*/ - -#define NV_CTRL_DDCCI_FIRST_VCP NV_CTRL_DDCCI_GEOMETRY_HORIZONTAL_POSITION -#define NV_CTRL_DDCCI_LAST_VCP NV_CTRL_DDCCI_CAPABLE -/**************************************************************************/ - /* * NV_CTRL_FLATPANEL_CHIP_LOCATION - for the specified display device, * report whether the flat panel is driven by the on-chip controller, @@ -2700,11 +1501,11 @@ #define NV_CTRL_GVO_OUTPUT_VIDEO_FORMAT2 227 /* --- */ /* - * Override the SDI hardware's Color Space Conversion with the values - * controlled through XNVCTRLSetGvoColorConversion() and - * XNVCTRLGetGvoColorConversion(). If this attribute is FALSE, then - * the values specified through XNVCTRLSetGvoColorConversion() are - * ignored. + * NV_CTRL_GVO_OVERRIDE_HW_CSC - Override the SDI hardware's Color Space + * Conversion with the values controlled through + * XNVCTRLSetGvoColorConversion() and XNVCTRLGetGvoColorConversion(). If + * this attribute is FALSE, then the values specified through + * XNVCTRLSetGvoColorConversion() are ignored. */ #define NV_CTRL_GVO_OVERRIDE_HW_CSC 228 /* RW- */ @@ -3121,7 +1922,7 @@ #define NV_CTRL_HWOVERLAY_TRUE 1 /* - * NV_CTRL_NUM_GPU_ERRORS_RECOVERED - Returns the number of gpu errors + * NV_CTRL_NUM_GPU_ERRORS_RECOVERED - Returns the number of GPU errors * occured. This attribute may be queried through XNVCTRLQueryTargetAttribute() * using a NV_CTRL_TARGET_TYPE_X_SCREEN target. */ @@ -3318,15 +2119,18 @@ /* - * NV_CTRL_SWITCH_TO_DISPLAYS takes display to which - * user wants to switch. + * NV_CTRL_SWITCH_TO_DISPLAYS - Can be used to select which displays + * to switch to (as a hotkey event). */ #define NV_CTRL_SWITCH_TO_DISPLAYS 276 /* -W- */ + /* - * NV_CTRL_NOTEBOOK_DISPLAY_CHANGE_LID_EVENT can be used to send event - * to notify open/closure of the lid. + * NV_CTRL_NOTEBOOK_DISPLAY_CHANGE_LID_EVENT - Event that notifies + * when a notebook lid change occurs (i.e. when the lid is opened or + * closed.) This attribute can be queried to retrieve the current + * notebook lid status (opened/closed.) */ #define NV_CTRL_NOTEBOOK_DISPLAY_CHANGE_LID_EVENT 277 /* RW- */ @@ -3334,8 +2138,8 @@ #define NV_CTRL_NOTEBOOK_DISPLAY_CHANGE_LID_EVENT_OPEN 1 /* - * NV_CTRL_NOTEBOOK_INTERNAL_LCD returns intenal LCD - * of Notebook. + * NV_CTRL_NOTEBOOK_INTERNAL_LCD - Returns the display device mask of + * the intenal LCD of a notebook. */ #define NV_CTRL_NOTEBOOK_INTERNAL_LCD 278 /* R-- */ @@ -3347,6 +2151,7 @@ #define NV_CTRL_DEPTH_30_ALLOWED 279 /* R--G */ + /* * NV_CTRL_MODE_SET_EVENT This attribute is sent as an event * when hotkey, ctrl-alt-+/- or randr event occurs. Note that @@ -3357,6 +2162,26 @@ #define NV_CTRL_MODE_SET_EVENT 280 /* --- */ + +/* + * NV_CTRL_OPENGL_AA_LINE_GAMMA_VALUE - the gamma value used by + * OpenGL when NV_CTRL_OPENGL_AA_LINE_GAMMA is enabled + */ + +#define NV_CTRL_OPENGL_AA_LINE_GAMMA_VALUE 281 /* RW-X */ + + +/* + * NV_CTRL_VCSC_HIGH_PERF_MODE - Is used to both query High Performance Mode + * status on the Visual Computing System, and also to enable or disable High + * Performance Mode. + */ + +#define NV_CTRL_VCSC_HIGH_PERF_MODE 282 /* RW-V */ +#define NV_CTRL_VCSC_HIGH_PERF_MODE_DISABLE 0 +#define NV_CTRL_VCSC_HIGH_PERF_MODE_ENABLE 1 + + /* * NV_CTRL_OPENGL_AA_LINE_GAMMA_VALUE - the gamma value used by * OpenGL when NV_CTRL_OPENGL_AA_LINE_GAMMA is enabled @@ -3403,6 +2228,14 @@ #define NV_CTRL_GVO_CSC_CHANGED_EVENT 294 /* --- */ +/* + * NV_CTRL_FRAMELOCK_SLAVEABLE - Returns a bitmask of the display devices + * that are (currently) allowed to be selected as slave devices for the + * given GPU + */ + +#define NV_CTRL_FRAMELOCK_SLAVEABLE 295 /* R-DG */ + /* * NV_CTRL_GVO_SYNC_TO_DISPLAY This attribute controls whether or not * the non-SDI display device will be sync'ed to the SDI display device @@ -3414,8 +2247,37 @@ #define NV_CTRL_GVO_SYNC_TO_DISPLAY_DISABLE 0 #define NV_CTRL_GVO_SYNC_TO_DISPLAY_ENABLE 1 +/* + * NV_CTRL_PIXMAP_CACHE - This attribute controls whether the driver attempts to + * store video memory pixmaps in a cache. The cache speeds up allocation and + * deallocation of pixmaps, but could use more memory than when the cache is + * disabled. + */ + +#define NV_CTRL_PIXMAP_CACHE 298 /* RW-X */ +#define NV_CTRL_PIXMAP_CACHE_DISABLE 0 +#define NV_CTRL_PIXMAP_CACHE_ENABLE 1 + +/* + * NV_CTRL_PIXMAP_CACHE_ROUNDING_SIZE_KB - When the pixmap cache is enabled and + * there is not enough free space in the cache to fit a new pixmap, the driver + * will round up to the next multiple of this number of kilobytes when + * allocating more memory for the cache. + */ + +#define NV_CTRL_PIXMAP_CACHE_ROUNDING_SIZE_KB 299 /* RW-X */ + +/* + * NV_CTRL_IS_GVO_DISPLAY - returns whether or not a given display is an + * SDI device. + */ + +#define NV_CTRL_IS_GVO_DISPLAY 300 /* R-D */ +#define NV_CTRL_IS_GVO_DISPLAY_FALSE 0 +#define NV_CTRL_IS_GVO_DISPLAY_TRUE 1 + -#define NV_CTRL_LAST_ATTRIBUTE NV_CTRL_GVO_SYNC_TO_DISPLAY +#define NV_CTRL_LAST_ATTRIBUTE NV_CTRL_IS_GVO_DISPLAY /**************************************************************************/ @@ -3483,33 +2345,6 @@ #define NV_CTRL_STRING_TV_ENCODER_NAME 5 /* R-DG */ -/* NV_CTRL_STRING_DDCCI_MISC_TRANSMIT_DISPLAY_DESCRIPTOR - - * Allows a display descriptor (up to maximum length defined by the - * display (see NV_CTRL_DDCCI_MISC_DISPLAY_DESCRIPTOR_LENGTHC2h) to be written - * (read) to (from) non-volatile storage in the display. - * If an attempt is made to write beyond the maximum storage - * length, the descriptor shall be truncated with the excess bytes - * being discarded. - */ - -#define NV_CTRL_STRING_DDCCI_MISC_TRANSMIT_DISPLAY_DESCRIPTOR 6 /* RWD */ - - -/* NV_CTRL_STRING_DDCCI_MISC_AUXILIARY_DISPLAY_DATA - - * An `auxiliary display' is a small alpha-numeric display associated - * with the primary display and able to be accessed via the primary - * display. - * This command transmits a number of bytes of alpha-numeric - * data to be displayed on the auxiliary display. The data shall - * conform to ISO 8859-2 (Latin 1) code set. - * The auxiliary display will be written from the top left position, - * moving to right along each line and then starting at left end of the - * next line. - */ - -#define NV_CTRL_STRING_DDCCI_MISC_AUXILIARY_DISPLAY_DATA 7 /* -WD */ - - /* * NV_CTRL_STRING_GVO_FIRMWARE_VERSION - indicates the version of the * Firmware on the GVO device. @@ -3840,8 +2675,101 @@ #define NV_CTRL_STRING_PERFORMANCE_MODES 29 /* R--G */ + +/* + * NV_CTRL_STRING_VCSC_FAN_STATUS - returns a string with status of all the + * fans in the Visual Computing System, if such a query is supported. Fan + * information is reported along with its tachometer reading (in RPM) and a + * flag indicating whether the fan has failed or not. + * + * Valid tokens: + * + * Token Value + * "fan" integer - the Fan index + * "speed" integer - the tachometer reading of the fan in rpm + * "fail" integer - flag to indicate whether the fan has failed + * + * Example: + * + * fan=0, speed=694, fail=0 ; fan=1, speed=693, fail=0 + * + * This attribute must be queried through XNVCTRLQueryTargetStringAttribute() + * using a NV_CTRL_TARGET_TYPE_VCSC target. + * + */ + +#define NV_CTRL_STRING_VCSC_FAN_STATUS 30 /* R---V */ + + +/* + * NV_CTRL_STRING_VCSC_TEMPERATURES - returns a string with all Temperature + * readings in the Visual Computing System, if such a query is supported. + * Intake, Exhaust and Board Temperature values are reported in Celcius. + * + * Valid tokens: + * + * Token Value + * "intake" integer - the intake temperature for the VCS + * "exhaust" integer - the exhaust temperature for the VCS + * "board" integer - the board temperature of the VCS + * + * Example: + * + * intake=29, exhaust=46, board=41 + * + * This attribute must be queried through XNVCTRLQueryTargetStringAttribute() + * using a NV_CTRL_TARGET_TYPE_VCSC target. + * + */ + +#define NV_CTRL_STRING_VCSC_TEMPERATURES 31 /* R---V */ + + +/* + * NV_CTRL_STRING_VCSC_PSU_INFO - returns a string with all Power Supply Unit + * related readings in the Visual Computing System, if such a query is + * supported. Current in amperes, Power in watts, Voltage in volts and PSU + * state may be reported. Not all PSU types support all of these values, and + * therefore some readings may be unknown. + * + * Valid tokens: + * + * Token Value + * "current" integer - the current drawn in amperes by the VCS + * "power" integer - the power drawn in watts by the VCS + * "voltage" integer - the voltage reading of the VCS + * "state" integer - flag to indicate whether PSU is operating normally + * + * Example: + * + * current=10, power=15, voltage=unknown, state=normal + * + * This attribute must be queried through XNVCTRLQueryTargetStringAttribute() + * using a NV_CTRL_TARGET_TYPE_VCSC target. + * + */ + + +#define NV_CTRL_STRING_VCSC_PSU_INFO 32 /* R---V */ + + +/* + * NV_CTRL_STRING_GVO_VIDEO_FORMAT_NAME - query the name for the specified + * NV_CTRL_GVO_VIDEO_FORMAT_*. So that this can be queried with existing + * interfaces, XNVCTRLQueryStringAttribute() should be used, and the video + * format specified in the display_mask field; eg: + * + * XNVCTRLQueryStringAttribute(dpy, + * screen, + * NV_CTRL_GVO_VIDEO_FORMAT_720P_60_00_SMPTE296, + * NV_CTRL_GVO_VIDEO_FORMAT_NAME, + * &name); + */ + +#define NV_CTRL_STRING_GVO_VIDEO_FORMAT_NAME 33 /* R--- */ + #define NV_CTRL_STRING_LAST_ATTRIBUTE \ - NV_CTRL_STRING_PERFORMANCE_MODES + NV_CTRL_STRING_GVO_VIDEO_FORMAT_NAME /**************************************************************************/ |