1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
|
.. SPDX-License-Identifier: GPL-2.0
============
I3C protocol
============
Disclaimer
==========
This chapter will focus on aspects that matter to software developers. For
everything hardware related (like how things are transmitted on the bus, how
collisions are prevented, ...) please have a look at the I3C specification.
This document is just a brief introduction to the I3C protocol and the concepts
it brings to the table. If you need more information, please refer to the MIPI
I3C specification (can be downloaded here
https://resources.mipi.org/mipi-i3c-v1-download).
Introduction
============
The I3C (pronounced 'eye-three-see') is a MIPI standardized protocol designed
to overcome I2C limitations (limited speed, external signals needed for
interrupts, no automatic detection of the devices connected to the bus, ...)
while remaining power-efficient.
I3C Bus
=======
An I3C bus is made of several I3C devices and possibly some I2C devices as
well, but let's focus on I3C devices for now.
An I3C device on the I3C bus can have one of the following roles:
* Master: the device is driving the bus. It's the one in charge of initiating
transactions or deciding who is allowed to talk on the bus (slave generated
events are possible in I3C, see below).
* Slave: the device acts as a slave, and is not able to send frames to another
slave on the bus. The device can still send events to the master on
its own initiative if the master allowed it.
I3C is a multi-master protocol, so there might be several masters on a bus,
though only one device can act as a master at a given time. In order to gain
bus ownership, a master has to follow a specific procedure.
Each device on the I3C bus has to be assigned a dynamic address to be able to
communicate. Until this is done, the device should only respond to a limited
set of commands. If it has a static address (also called legacy I2C address),
the device can reply to I2C transfers.
In addition to these per-device addresses, the protocol defines a broadcast
address in order to address all devices on the bus.
Once a dynamic address has been assigned to a device, this address will be used
for any direct communication with the device. Note that even after being
assigned a dynamic address, the device should still process broadcast messages.
I3C Device discovery
====================
The I3C protocol defines a mechanism to automatically discover devices present
on the bus, their capabilities and the functionalities they provide. In this
regard I3C is closer to a discoverable bus like USB than it is to I2C or SPI.
The discovery mechanism is called DAA (Dynamic Address Assignment), because it
not only discovers devices but also assigns them a dynamic address.
During DAA, each I3C device reports 3 important things:
* BCR: Bus Characteristic Register. This 8-bit register describes the device bus
related capabilities
* DCR: Device Characteristic Register. This 8-bit register describes the
functionalities provided by the device
* Provisional ID: A 48-bit unique identifier. On a given bus there should be no
Provisional ID collision, otherwise the discovery mechanism may fail.
I3C slave events
================
The I3C protocol allows slaves to generate events on their own, and thus allows
them to take temporary control of the bus.
This mechanism is called IBI for In Band Interrupts, and as stated in the name,
it allows devices to generate interrupts without requiring an external signal.
During DAA, each device on the bus has been assigned an address, and this
address will serve as a priority identifier to determine who wins if 2 different
devices are generating an interrupt at the same moment on the bus (the lower the
dynamic address the higher the priority).
Masters are allowed to inhibit interrupts if they want to. This inhibition
request can be broadcast (applies to all devices) or sent to a specific
device.
I3C Hot-Join
============
The Hot-Join mechanism is similar to USB hotplug. This mechanism allows
slaves to join the bus after it has been initialized by the master.
This covers the following use cases:
* the device is not powered when the bus is probed
* the device is hotplugged on the bus through an extension board
This mechanism is relying on slave events to inform the master that a new
device joined the bus and is waiting for a dynamic address.
The master is then free to address the request as it wishes: ignore it or
assign a dynamic address to the slave.
I3C transfer types
==================
If you omit SMBus (which is just a standardization on how to access registers
exposed by I2C devices), I2C has only one transfer type.
I3C defines 3 different classes of transfer in addition to I2C transfers which
are here for backward compatibility with I2C devices.
I3C CCC commands
----------------
CCC (Common Command Code) commands are meant to be used for anything that is
related to bus management and all features that are common to a set of devices.
CCC commands contain an 8-bit CCC ID describing the command that is executed.
The MSB of this ID specifies whether this is a broadcast command (bit7 = 0) or a
unicast one (bit7 = 1).
The command ID can be followed by a payload. Depending on the command, this
payload is either sent by the master sending the command (write CCC command),
or sent by the slave receiving the command (read CCC command). Of course, read
accesses only apply to unicast commands.
Note that, when sending a CCC command to a specific device, the device address
is passed in the first byte of the payload.
The payload length is not explicitly passed on the bus, and should be extracted
from the CCC ID.
Note that vendors can use a dedicated range of CCC IDs for their own commands
(0x61-0x7f and 0xe0-0xef).
I3C Private SDR transfers
-------------------------
Private SDR (Single Data Rate) transfers should be used for anything that is
device specific and does not require high transfer speed.
It is the equivalent of I2C transfers but in the I3C world. Each transfer is
passed the device address (dynamic address assigned during DAA), a payload
and a direction.
The only difference with I2C is that the transfer is much faster (typical clock
frequency is 12.5MHz).
I3C HDR commands
----------------
HDR commands should be used for anything that is device specific and requires
high transfer speed.
The first thing attached to an HDR command is the HDR mode. There are currently
3 different modes defined by the I3C specification (refer to the specification
for more details):
* HDR-DDR: Double Data Rate mode
* HDR-TSP: Ternary Symbol Pure. Only usable on busses with no I2C devices
* HDR-TSL: Ternary Symbol Legacy. Usable on busses with I2C devices
When sending an HDR command, the whole bus has to enter HDR mode, which is done
using a broadcast CCC command.
Once the bus has entered a specific HDR mode, the master sends the HDR command.
An HDR command is made of:
* one 16-bits command word in big endian
* N 16-bits data words in big endian
Those words may be wrapped with specific preambles/post-ambles which depend on
the chosen HDR mode and are detailed here (see the specification for more
details).
The 16-bits command word is made of:
* bit[15]: direction bit, read is 1, write is 0
* bit[14:8]: command code. Identifies the command being executed, the amount of
data words and their meaning
* bit[7:1]: I3C address of the device this command is addressed to
* bit[0]: reserved/parity-bit
Backward compatibility with I2C devices
=======================================
The I3C protocol has been designed to be backward compatible with I2C devices.
This backward compatibility allows one to connect a mix of I2C and I3C devices
on the same bus, though, in order to be really efficient, I2C devices should
be equipped with 50 ns spike filters.
I2C devices can't be discovered like I3C ones and have to be statically
declared. In order to let the master know what these devices are capable of
(both in terms of bus related limitations and functionalities), the software
has to provide some information, which is done through the LVR (Legacy I2C
Virtual Register).
|
