diff options
Diffstat (limited to 'sound')
| -rw-r--r-- | sound/pci/hda/patch_realtek.c | 173 |
1 files changed, 170 insertions, 3 deletions
diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 8ec2db2e9b60..ea4200a4ee42 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -6,6 +6,7 @@ * Copyright (c) 2004 Kailang Yang <kailang@realtek.com.tw> * PeiSen Hou <pshou@realtek.com.tw> * Takashi Iwai <tiwai@suse.de> + * Jonathan Woithe <jwoithe@physics.adelaide.edu.au> * * This driver is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -63,6 +64,9 @@ enum { ALC260_HP, ALC260_HP_3013, ALC260_FUJITSU_S702X, +#ifdef CONFIG_SND_DEBUG + ALC260_TEST, +#endif ALC260_AUTO, ALC260_MODEL_LAST /* last tag */ }; @@ -223,13 +227,19 @@ static int alc_ch_mode_put(struct snd_kcontrol *kcontrol, struct snd_ctl_elem_va * instead of "%" to avoid consequences of accidently treating the % as * being part of a format specifier. Maximum allowed length of a value is * 63 characters plus NULL terminator. + * + * Note: some retasking pin complexes seem to ignore requests for input + * states other than HiZ (eg: PIN_VREFxx) and revert to HiZ if any of these + * are requested. Therefore order this list so that this behaviour will not + * cause problems when mixer clients move through the enum sequentially. + * NIDs 0x0f and 0x10 have been observed to have this behaviour. */ static char *alc_pin_mode_names[] = { - "Line in", "Mic 80pc bias", "Mic 50pc bias", - "Line out", "Headphone out", + "Mic 50pc bias", "Mic 80pc bias", + "Line in", "Line out", "Headphone out", }; static unsigned char alc_pin_mode_values[] = { - PIN_IN, PIN_VREF80, PIN_VREF50, PIN_OUT, PIN_HP, + PIN_VREF50, PIN_VREF80, PIN_IN, PIN_OUT, PIN_HP, }; /* The control can present all 5 options, or it can limit the options based * in the pin being assumed to be exclusively an input or an output pin. @@ -2770,6 +2780,146 @@ static struct hda_verb alc260_fujitsu_init_verbs[] = { { } }; +/* Test configuration for debugging, modelled after the ALC880 test + * configuration. + */ +#ifdef CONFIG_SND_DEBUG +static hda_nid_t alc260_test_dac_nids[1] = { + 0x02, +}; +static hda_nid_t alc260_test_adc_nids[2] = { + 0x04, 0x05, +}; +static struct hda_input_mux alc260_test_capture_source = { + .num_items = 7, + .items = { + { "MIC1 pin", 0x0 }, + { "MIC2 pin", 0x1 }, + { "LINE1 pin", 0x2 }, + { "LINE2 pin", 0x3 }, + { "CD pin", 0x4 }, + { "LINE-OUT pin", 0x5 }, + { "HP-OUT pin", 0x6 }, + }, +}; +static struct snd_kcontrol_new alc260_test_mixer[] = { + /* Output driver widgets */ + HDA_CODEC_VOLUME_MONO("Mono Playback Volume", 0x0a, 1, 0x0, HDA_OUTPUT), + HDA_BIND_MUTE_MONO("Mono Playback Switch", 0x0a, 1, 2, HDA_INPUT), + HDA_CODEC_VOLUME("LOUT2 Playback Volume", 0x09, 0x0, HDA_OUTPUT), + HDA_BIND_MUTE("LOUT2 Playback Switch", 0x09, 2, HDA_INPUT), + HDA_CODEC_VOLUME("LOUT1 Playback Volume", 0x08, 0x0, HDA_OUTPUT), + HDA_BIND_MUTE("LOUT1 Playback Switch", 0x08, 2, HDA_INPUT), + + /* Modes for retasking pin widgets */ + ALC_PIN_MODE("HP-OUT pin mode", 0x10, ALC_PIN_DIR_INOUT), + ALC_PIN_MODE("LINE-OUT pin mode", 0x0f, ALC_PIN_DIR_INOUT), + ALC_PIN_MODE("LINE2 pin mode", 0x15, ALC_PIN_DIR_INOUT), + ALC_PIN_MODE("LINE1 pin mode", 0x14, ALC_PIN_DIR_INOUT), + ALC_PIN_MODE("MIC2 pin mode", 0x13, ALC_PIN_DIR_INOUT), + ALC_PIN_MODE("MIC1 pin mode", 0x12, ALC_PIN_DIR_INOUT), + + /* Loopback mixer controls */ + HDA_CODEC_VOLUME("MIC1 Playback Volume", 0x07, 0x00, HDA_INPUT), + HDA_CODEC_MUTE("MIC1 Playback Switch", 0x07, 0x00, HDA_INPUT), + HDA_CODEC_VOLUME("MIC2 Playback Volume", 0x07, 0x01, HDA_INPUT), + HDA_CODEC_MUTE("MIC2 Playback Switch", 0x07, 0x01, HDA_INPUT), + HDA_CODEC_VOLUME("LINE1 Playback Volume", 0x07, 0x02, HDA_INPUT), + HDA_CODEC_MUTE("LINE1 Playback Switch", 0x07, 0x02, HDA_INPUT), + HDA_CODEC_VOLUME("LINE2 Playback Volume", 0x07, 0x03, HDA_INPUT), + HDA_CODEC_MUTE("LINE2 Playback Switch", 0x07, 0x03, HDA_INPUT), + HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT), + HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT), + HDA_CODEC_VOLUME("Beep Playback Volume", 0x07, 0x05, HDA_INPUT), + HDA_CODEC_MUTE("Beep Playback Switch", 0x07, 0x05, HDA_INPUT), + HDA_CODEC_VOLUME("LINE-OUT loopback Playback Volume", 0x07, 0x06, HDA_INPUT), + HDA_CODEC_MUTE("LINE-OUT loopback Playback Switch", 0x07, 0x06, HDA_INPUT), + HDA_CODEC_VOLUME("HP-OUT loopback Playback Volume", 0x07, 0x7, HDA_INPUT), + HDA_CODEC_MUTE("HP-OUT loopback Playback Switch", 0x07, 0x7, HDA_INPUT), + { } /* end */ +}; +static struct hda_verb alc260_test_init_verbs[] = { + /* Disable all GPIOs */ + {0x01, AC_VERB_SET_GPIO_MASK, 0}, + /* Enable retasking pins as output, initially without power amp */ + {0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, + {0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, + {0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, + {0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, + {0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, + {0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT}, + + /* Disable digital (SPDIF) pins for now */ + {0x03, AC_VERB_SET_DIGI_CONVERT_1, 0}, + {0x06, AC_VERB_SET_DIGI_CONVERT_1, 0}, + + /* Ensure mic1, mic2, line1 and line2 pin widget take input from the + * OUT1 sum bus when acting as an output. + */ + {0x0b, AC_VERB_SET_CONNECT_SEL, 0}, + {0x0c, AC_VERB_SET_CONNECT_SEL, 0}, + {0x0d, AC_VERB_SET_CONNECT_SEL, 0}, + {0x0e, AC_VERB_SET_CONNECT_SEL, 0}, + + /* Start with output sum widgets muted and their output gains at min */ + {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, + {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, + {0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, + {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, + {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, + {0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, + {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, + {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, + {0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO}, + + /* Unmute retasking pin widget output amp left/right (no mixer ctrl) */ + {0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + {0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + {0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + {0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + /* Also unmute the mono-out pin widget */ + {0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE}, + + /* Also unmute the retasking pin input amps. Having the input and + * output amps unmuted at the same time doesn't appear to cause any + * trouble. + */ + {0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, + {0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, + {0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, + {0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, + {0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, + {0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)}, + + /* Mute capture amp left and right */ + {0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, + /* Set ADC connection select to match default mixer setting - line + * in (on mic1 pin) + */ + {0x04, AC_VERB_SET_CONNECT_SEL, 0x00}, + + /* Do the same for the second ADC: mute capture input amp and + * set ADC connection to line in + */ + {0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, + {0x05, AC_VERB_SET_CONNECT_SEL, 0x00}, + + /* Mute all inputs to mixer widget (even unconnected ones) */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */ + {0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */ + + { } +}; +#endif + static struct hda_pcm_stream alc260_pcm_analog_playback = { .substreams = 1, .channels_min = 2, @@ -3053,6 +3203,9 @@ static struct hda_board_config alc260_cfg_tbl[] = { { .pci_subvendor = 0x103c, .pci_subdevice = 0x3016, .config = ALC260_HP }, { .modelname = "fujitsu", .config = ALC260_FUJITSU_S702X }, { .pci_subvendor = 0x10cf, .pci_subdevice = 0x1326, .config = ALC260_FUJITSU_S702X }, +#ifdef CONFIG_SND_DEBUG + { .modelname = "test", .config = ALC260_TEST }, +#endif { .modelname = "auto", .config = ALC260_AUTO }, {} }; @@ -3110,6 +3263,20 @@ static struct alc_config_preset alc260_presets[] = { .channel_mode = alc260_modes, .input_mux = &alc260_fujitsu_capture_source, }, +#ifdef CONFIG_SND_DEBUG + [ALC260_TEST] = { + .mixers = { alc260_test_mixer, + alc260_capture_mixer }, + .init_verbs = { alc260_test_init_verbs }, + .num_dacs = ARRAY_SIZE(alc260_test_dac_nids), + .dac_nids = alc260_test_dac_nids, + .num_adc_nids = ARRAY_SIZE(alc260_test_adc_nids), + .adc_nids = alc260_test_adc_nids, + .num_channel_mode = ARRAY_SIZE(alc260_modes), + .channel_mode = alc260_modes, + .input_mux = &alc260_test_capture_source, + }, +#endif }; static int patch_alc260(struct hda_codec *codec) |