| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When the interface is down and we are using polled mode for MCDI
operations, we busy-wait for completion for approximately 1 jiffy
using udelay() and then back off to schedule(). But the completion
will not wake the task, since we are using polled mode! We must use
schedule_timeout_uninterruptible() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes a delay in hardware after every received packet allowing
more time for transmitted packets to go out in between received packets in
half duplex.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A previous 82577 workaround that set the MDIO access speed to slow mode for
every PHY register read/write when the cable is unplugged should instead
set the access mode to always be slow before any PHY register access.
Since the mode bit gets cleared when the PHY is reset, set the mode after
every PHY reset.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch resolves issues seen when running netconsole and rebooting via
reboot -f. The issue was due to the fact that we were attempting to
perform interrupt actions when the q_vectors and rings had already been
freed via the ixgbe_shutdown routines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://xenbits.xensource.com/people/ianc/linux-2.6
* 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: fix hang on suspend.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: change drm set mode messages as DRM_DEBUG
drm: fix crtc no modes printf + typo
drm/radeon/kms: only evict to GTT if CP is ready
drm/radeon/kms: Fix crash getting TV info with no BIOS.
drm/radeon/kms/rv100: reject modes > 135 Mhz on DVI (v2)
drm/radeon/kms/r6xx+: make irq handler less verbose
drm/radeon/kms: fix up LVDS handling on macs (v2)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: Add BTN_TOOL_FINGER for pad button reporting
HID: add device IDs for new model of Apple Wireless Keyboard
HID: fix pad button definition in hid-wacom
HID: Support 171 byte variant of Samsung USB IR receiver
HID: blacklist ET&T TC5UH touchscreen controller
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
It's not obvious that copy_from_user() is called with a sane length
parameter here. Even though it currently seems to be correct better
add a check to prevent stack corruption / exploits.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
...instead of adding a compat ioctl function which would do nothing
as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This is just a complicated construct which always returns -EINVAL.
Just remove it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add missing compat ptr conversion including two additional
whitespace changes that aren't worth a separate patch.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Without this patch xf86-input-wacom driver wasn't able to properly recognise
pad button events. It was also causing some problems with button mapping.
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Added device IDs for the new model of the Apple Wireless Keyboard
(November 2009).
Signed-off-by: Christian Schuerer-Waldheim <csw@xray.at>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This fix is required for xorg driver to recognise 2 pad buttons
Signed-off-by: Przemo Firszt <przemo@firszt.eu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In 65f63384 "xen: improve error handling in do_suspend" I said:
- xs_suspend()/xs_resume() and dpm_suspend_noirq()/dpm_resume_noirq() were not
nested in the obvious way.
and changed the ordering of the calls as so:
BEFORE AFTER
xs_suspend dpm_suspend_noirq
dpm_suspend_noirq xs_suspend
*SUSPEND* *SUSPEND*
dpm_resume_noirq dpm_resume_noirq
xs_resume xs_resume
Clearly this is not an improvement and I was talking rubbish.
In particular the new ordering is susceptible to a hang if a xenstore write is
in progress at the point at which the suspend kicks in. When the suspend
process calls xs_suspend it tries to take the request_mutex but if a write is
in progress it could be looping in xenbus_xs.c:read_reply() waiting for
something to arrive on &xs_state.reply_list while holding the request_mutex
(taken in the caller of read_reply).
However if we have done dpm_suspend_noirq before xs_suspend then we won't get
any more xenstore interrupts and process_msg() will never be woken up to add
anything to the reply_list.
Fix this by calling xs_suspend before dpm_suspend_noirq. If dpm_suspend_noirq
fails then make sure we go through the xs_suspend_cancel() code path.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
|
|
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Sentelic probes confuse IBM trackpoints so they stop responding to
TP_READ_ID command. See:
http://bugzilla.kernel.org/show_bug.cgi?id=14970
Let's move FSP detection lower so it is probed after trackpoint and
others, just before we strat probing for Intellimouse Explorer.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
* korg/drm-radeon-next
drm/radeon/kms: only evict to GTT if CP is ready
drm/radeon/kms: Fix crash getting TV info with no BIOS.
drm/radeon/kms/rv100: reject modes > 135 Mhz on DVI (v2)
drm/radeon/kms/r6xx+: make irq handler less verbose
drm/radeon/kms: fix up LVDS handling on macs (v2)
|
|
Following drm info repeat 207 times during one hour, it's quite annoying
[ 1266.286747] [drm] TV-19: set mode NTSC 480i 0
Change from DRM_INFO to DRM_DEBUG
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Toralf Förster pointed out the typo, the fact I forget the if
statement is purely personal fail.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
* git://git.infradead.org/battery-2.6:
pmu_battery: Fix battery full reporting
|
|
/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior).
This turns off group and user write permissions, so that on typical
production systems only root can write to it.
Signed-off-by: Bryn M. Reeves <bmr@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
OMAP: DSS2: OMAPFB: fix crash when panel driver was not loaded
OMAP: DSS2: Reject scaling settings when they cannot be supported
OMAP: DSS2: Make check-delay-loops consistent
OMAP: DSS2: OMAPFB: fix omapfb_free_fbmem()
video/omap: add __init/__exit macros to drivers/video/omap/lcd_htcherald.c
OMAP: DSS2: Fix compile warning
MAINTAINERS: Combine DSS2 and OMAPFB2 into one entry
MAINTAINERS: change omapfb maintainer
OMAP: OMAPFB: add dummy release function for omapdss
OMAP: OMAPFB: fix clk_get for RFBI
OMAP: DSS2: RFBI: convert to new kfifo API
OMAP: DSS2: Fix crash when panel doesn't define enable_te()
OMAP: DSS2: Collect interrupt statistics
OMAP: DSS2: DSI: print debug DCS cmd in hex
OMAP: DSS2: DSI: fix VC channels in send_short and send_null
|
|
There are two copies of list_sort() in the tree already, one in the DRM
code, another in ubifs. Now XFS needs this as well. Create a generic
list_sort() function from the ubifs version and convert existing users
to it so we don't end up with yet another copy in the tree.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: retry link resume if necessary
ata_piix: enable 32bit PIO on SATA piix
sata_promise: don't classify overruns as HSM errors
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
sky2: Fix oops in sky2_xmit_frame() after TX timeout
Documentation/3c509: document ethtool support
af_packet: Don't use skb after dev_queue_xmit()
vxge: use pci_dma_mapping_error to test return value
netfilter: ebtables: enforce CAP_NET_ADMIN
e1000e: fix and commonize code for setting the receive address registers
e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
e1000e: perform 10/100 adaptive IFS only on parts that support it
e1000e: don't accumulate PHY statistics on PHY read failure
e1000e: call pci_save_state() after pci_restore_state()
netxen: update version to 4.0.72
netxen: fix set mac addr
netxen: fix smatch warning
netxen: fix tx ring memory leak
tcp: update the netstamp_needed counter when cloning sockets
TI DaVinci EMAC: Handle emac module clock correctly.
dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
ixgbe: Fix compiler warning about variable being used uninitialized
netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
mv643xx_eth: don't include cache padding in rx desc buffer size
...
Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
|
|
Testing GTT ready might be more correct but cp.ready
works fine and has been tested on irc by 2-3 ppl.
fixes bug k.org 15035 and fd.o 25733
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Due to heat issues. Fixes fdo bug 25992
v2: fix typo noticed by Maarten Maathuis
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Unhandled vectors can be safely ignored, no need
to spam the kernel log by default.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Based on radeonfb code and recent ddx fix.
v2: minor formatting fix from Michel Dänzer
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Tested-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 871af1210f13966ab911ed2166e4ab2ce775b99d enabled 32bit PIO for
PATA piix but didn't for SATA. There's no reason not to use 32bit PIO
on SATA piix. Enable it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When sata_promise encounters an overrun or underrun error it
translates that to a libata AC_ERR_HSM, causing a hard reset.
Since over/under-runs were thought to be rare and transient,
this action seemed reasonable.
Unfortunately it turns out that the controller throws overrun
errors when e.g. hal polls a CD or DVD writer containing blank
media, causing long sequences of hard resets and retries before
EH finally gives up.
This patch updates sata_promise to classify over/under-runs as
AC_ERR_OTHER instead. This allows libata EH and upper layers to
retry or fail the operation as they see fit without the disruption
caused by repeated hard resets.
This fixes a problem using a DVD-RAM drive with sata_promise,
reported by Thomas Schorpp. I also tested it on a DVD-RW drive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: thomas schorpp <thomas.schorpp@googlemail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Input core displays capabilities bitmasks in form of one or more longs printed
in hex form and separated by spaces. Unfortunately it does not work well
for 32-bit applications running on 64-bit kernels since applications expect
that number is "worth" only 32 bits when kernel advances by 64 bits.
Fix that by ensuring that output produced for compat tasks uses 32-bit units.
Reported-and-tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
During TX timeout procedure dev could be awoken too early, e.g. by
sky2_complete_tx() called from sky2_down(). Then sky2_xmit_frame()
can run while buffers are freed causing an oops. This patch fixes it
by adding netif_device_present() test in sky2_tx_complete().
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=14925
With debugging by: Mike McCormack <mikem@ring3k.org>
Reported-by: Berck E. Nash <flyboy@gmail.com>
Tested-by: Berck E. Nash <flyboy@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the panel's probe had failed, omapfb would still go on, eventually
crashing.
A better fix would be to handle each display properly, and leaving just
the failed display out. But that is a bigger change.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
If the scaling ratio is below 0.5 video output width can't be identical
to the display width. Reject such settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
|
|
Smatch (and presumably other static checkers) complain that MAX_TID_COUNT is
past the end of the array. In the resulting discussion, Zhu Yi pointed out
that this value is not used in real life and the assignment was only there to
silence a gcc warning.
If there were a bug in the surrounding code and the value were used, the
WARN_ON(!qc) would print a warning before the crash.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/hp: fail gracefully if we don't find an IOC
agp/hp: fixup hp agp after ACPI changes
agp: correct missing cleanup on error in agp_add_bridge
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (45 commits)
drm/nv04: Fix set_operation software method.
drm/nouveau: initialise DMA tracking parameters earlier
drm/nouveau: use dma.max rather than pushbuf size for checking GET validity
drm/nv04: differentiate between nv04/nv05
drm/nouveau: Fix null deref in nouveau_fence_emit due to deleted fence
drm/nv50: prevent a possible ctxprog hang
drm/nouveau: have ttm's fault handler called directly
drm/nv50: restore correct cache1 get/put address on fifoctx load
drm/nouveau: create function for "dealing" with gpu lockup
drm/nouveau: remove unused nouveau_channel_idle() function
drm/nouveau: fix handling of fbcon colours in 8bpp
drm/nv04: Context switching fixes.
drm/nouveau: Use the software object for fencing.
drm/nouveau: Allocate a per-channel instance of NV_SW.
drm/nv50: make the blocksize depend on vram size
drm/nouveau: better alignment of bo sizes and use roundup instead of ALIGN
drm/nouveau: Don't skip card take down on nv0x.
drm/nouveau: Implement nv42-nv43 TV load detection.
drm/nouveau: Clean up the nv17-nv4x load detection code a bit.
drm/nv50: fix fillrect color
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: Make PCI device ids constant
hwmon: (coretemp) Fix TjMax for Atom N450/D410/D510 CPUs
hwmon: (k10temp) Blacklist more family 10h processors
hwmon: (asus_atk0110) Add debugfs interface
hwmon: (asus_atk0110) Refactor interface probe code
hwmon: (adt7462) Fix pin 28 monitoring
|
