| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
The encoding is tightly packed, and future changes (such as
pinconf-generic support) can easily lead to a situation where we violate
the encoding constraints and trample data bit/reg bits. This plugs in
some sanity checks by way of a BUILD_BUG_ON() to blow up if we fail to
fit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
WANT_PULLUP/DOWN were never interfaced with anything, so just kill them
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This implements some Kconfig knobs for ensuring that the PFC gpio chip
can be disabled or built as a module in the cases where it's optional, or
forcibly enabled in cases where it's not.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This implements a bit of rework for the PFC code, making the core itself
slightly more pluggable and moving out the gpio chip handling completely.
The API is preserved in such a way that platforms that depend on it for
early configuration are still able to do so, while making it possible to
migrate to alternate interfaces going forward.
This is the first step of chainsawing necessary to support the pinctrl
API, with the eventual goal being able to decouple pin function state
from the gpio API while retaining gpio chip tie-in for gpio pin functions
only, relying on the pinctrl/pinmux API for non-gpio function demux.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One small bug fix, plus a rename of all the ST Ericsson regulators in
the device tree since all the device trees had been written with
different names and some infelicities in the test proceedures meant
that the device tree code had apparently never actually been run
against the upstream device tree."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Change db8500-prcmu match names to reflect Device Tree
regulator: Change ab8500 match names to reflect Device Tree
regulator: Fix the s5m8767a problem of the division by null
|
|
Pull EDAC fixes from Mauro Carvalho Chehab.
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: Do alignment logic properly in edac_align_ptr()
mpc85xx_edac: fix error: too few arguments to function 'edac_mc_alloc'
edac: fix the error about memory type detection on SandyBridge
edac: avoid mce decoding crash after edac driver unloaded
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull a 9p bugfix from Eric Van Hensbergen.
* 'v9fs-devel' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: BUG before corrupting memory
|
|
Pull a crypto fix from Herbert Xu:
"This push fixes another bug in the atmel-rng that made it produce
completely useless output."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: atmel-rng - fix data valid check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- atmel-mci: Fixes for NULL timer and DMA burst/chunk size
- dw_mmc: Fix DMA ordering, clkdiv calculation, NULL host->data
- mxs_mmc: Compile fix for CONFIG_OF=y && CONFIG_PM=n
- omap: Fix NULL deref in mmc_omap_remove_slot(), reg_shift initialization
- sdhci-s3c: Fix boot regression by adding IRQF_ONESHOT flag
- Small fixes to core/sd, core/sdio, sdhci
* tag 'mmc-fixes-for-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: mxs-mmc: Move of_match_table out of CONFIG_PM
mmc: sdhci-s3c: pass IRQF ONESHOT to request threaded irq
mmc: core: return an error on suspend if mmc_deselect_cards fails
mmc: omap: Fix broken reg_shift initialization
mmc: omap: Fix NULL pointer dereference if mmc_omap_new_slot() fails
mmc: omap: Fix a section warning regression
mmc: dw_mmc: correct the calculation for CLKDIV
mmc: dw_mmc: fix incorrect setting of host->data of NULL
mmc: dw_mmc: fix the IDMAC sw reset
mmc: dw_mmc: fix the transmission handling in IDMAC
mmc: sdio: fix setting card data bus width as 4-bit
mmc: atmel-mci: fix burst/chunk size modification
mmc: atmel-mci: fix data timeout issue
mmc: sdhci: Use DBG() instead of pr_warning() on large timeout
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc
Pull remoteproc fixes from Ohad Ben-Cohen:
"A few relatively-small remoteproc fixes for 3.5: two error path fixes,
and one -Wformat warning fix."
* tag 'rproc-fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ohad/remoteproc:
remoteproc/omap: fix dev_err typo
remoteproc: fix missing fault indication in error-path
remoteproc: fix print format warnings
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon subsystem fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (coretemp) Drop needless initialization
hwmon: (coretemp) Document TjMax for 3rd generation i5/i7 processors
hwmon: (coretemp) Improve support for TjMax detection on Atom CPUs
hwmon: (coretemp) Add support for Atom D2000 and N2000 series CPU models
hwmon: (coretemp) Improve support of recent Atom CPU models
|
|
The asm-generic/bug.h __ASSEMBLY__ guarding is completely bogus, which
tripped up the powerpc build when the kernel.h include was added:
In file included from include/asm-generic/bug.h:5:0,
from arch/powerpc/include/asm/bug.h:127,
from arch/powerpc/kernel/head_64.S:31:
include/linux/kernel.h:44:0: warning: "ALIGN" redefined [enabled by default]
include/linux/linkage.h:57:0: note: this is the location of the previous definition
include/linux/sysinfo.h: Assembler messages:
include/linux/sysinfo.h:7: Error: Unrecognized opcode: `struct'
include/linux/sysinfo.h:8: Error: Unrecognized opcode: `__kernel_long_t'
Moving the __ASSEMBLY__ guard up and stashing the kernel.h include under
it fixes this up, as well as covering the case the original fix was
attempting to handle.
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the READABLE_ASM cc-option tests were added they were done so prior
to the arch Makefile include, resulting in cc-option being run on the
host cc instead of the factoring in the cross prefix set up by the
architecture.
This bumps the include back up so that cc-option actually runs on the
compiler that we're building with.
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge hfsplus fixes from Christoph Hellwig:
"Two small hfsplus fixes:
- a one liner regression fix for large volume handling from Janne
Kalliomäki.
- a fixup for the boot image blessing feature to make it work with
the fake "hardlinks" in hfsplus from Matthew Garrett."
* branch 'hfsplus':
hfsplus: fix bless ioctl when used with hardlinks
hfsplus: fix overflow in sector calculations in hfsplus_submit_bio
|
|
HFS+ doesn't really implement hard links - instead, hardlinks are indicated
by a magic file type which refers to an indirect node in a hidden
directory. The spec indicates that stat() should return the inode number
of the indirect node, but it turns out that this doesn't satisfy the
firmware when it's looking for a bootloader - it wants the catalog ID of
the hardlink file instead. Fix up this case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The variable io_size was unsigned int, which caused the wrong sector number
to be calculated after aligning it. This then caused mount to fail with big
volumes, as backup volume header information was searched from a
wrong sector.
Signed-off-by: Janne Kalliomäki <janne@tuxera.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the db8500-prcum regulator driver so
this is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
If ramp_delay is 0, delay value can be divided by zero.
This patch can fix the problem.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The value is overridden a few lines later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Tjmax values from Intel datasheets.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Atom CPUs don't have a register to retrieve TjMax. Detection so far was
incomplete. Use the X86 model ID to improve it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Document the Atom series D2000 and N2000 (Cedar Trail) as being supported.
List and set TjMax for those series.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Document the new Atom series (Tunnel Creek and Medfield) as being
supported, and list TjMax for the Atom E600 series.
Also enable the Atom tjmax heuristic for these Atom CPU models.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
|
|
Pull drm fixes from Dave Airlie:
"Radeon is most of the work, one regression, one BUG fix in the new
prime code, some fixes to init code to make streamout not lock up the
hardware, and just some code to enable users to test HDMI audio on
later hw (its off by default).
Intel adds edp edid caching for some strange Dell Vostros that black
screen on startup if keep reading their EDID, and a fix for a DP
regression.
Otherwise fix for via/sis and one to stop udl binding to multiple
non-video usb."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
drm/radeon: add support for STRMOUT_BASE_UPDATE on 7xx
drm/radeon: add some additional 6xx/7xx/EG register init
drm/radeon: enable HDMI on DCE5 (AKA NI excluding Aruba)
drm sis: initialize object_idr
drm via: initialize object_idr
drm/radeon/prime: reserve/unreserve around pin
drm/radeon: fix regression in dynpm due to multi-ring rework
vga_switcheroo.h: fix pci_dev warning
drm/udl: only bind to the video devices on the hub.
|
|
For some reason one of the dev_err invocations is using a wrong
device so fix that.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A bit larger set than usual, unfortunately -- I've been sitting on
them longer than I meant to so it's really more like 2 -rc pull
requests in one, volume-wise.
Nearly everything is fixes for fallout from the merge window, or other
fixes for bugs. The one exception is the highbank L2-enablement
patch, but it was contained enough that I picked it up anyway:
- i.MX fixes, mostly for clock and pinctrl changes
- OMAP fixes, mostly PM-related
- A patch to enable L2 on highbank
- A couple of fixes for PXA, Kirkwood, Versatile"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: Kirkwood: Fix clk problems modular ethernet driver
arm: versatile: fix and enable PCI I/O space
ARM: highbank: Add smc calls to enable/disable the L2
ARM i.MX imx21ads: Fix overlapping static i/o mappings
ARM: imx6: exit coherency when shutting down a cpu
ARM: mx51: Add pinctrl_provide_dummies()
ARM: mx31: Add pinctrl_provide_dummies()
ARM: OMAP2+: Fix compile for CONFIG_TIDSPBRIDGE platform init code
ARM: OMAP3: Fix omap3_l3_block_irq warning when CONFIG_BUG is not set
ARM: OMAP: Fix MMC_OMAP build when only MMC_OMAP_HS is selected
OMAP2+: UART: Add mechanism to probe uart pins and configure rx wakeup
ARM: mmp: fix missing cascade_irq in irq handler
ARM: dts: update memory size on brownstone
ARM i.MX27 Visstrim M10: fix gpio handling.
ARM i.MX53: Fix PLL4 base address
ARM i.MX pllv2: make round_rate accurate
ARM i.MX pllv2: use standard register set unconditionally
ARM: OMAP: Fix lis3lv02d accelerometer to use gpio_to_irq
ARM: imx: only call l2x0_init if it's available
ARM: imx: only specify i2c device type once
...
|
|
When the ethernet driver was built as a module, it would lock the
machine when loaded. At boot the ethernet clks are unused, so get
turned off. Later, when the module is loaded, the probe function
would access the hardware before the clock was restarted, and the
machine would lock. It has also been determined that when the clk is
turned off, the interface forgets its MAC address, which for most
systems, is set by the boot loader.
When the machine setup file creates a platform device for the
interface, prepare and enable the clock for the interface. This will
ensure it is not turned off. However, if the setup file only
instantiates one platform device, the other will have its clk
disabled, thus maybe saving a little power.
Report-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With commit 4d5fc58dbe34b (ARM: remove bunch of now unused
mach/io.h files), the I/O space setup was completely broken on
versatile. This patch fixes that and prepares for further
I/O space clean-up.
I/O space handling on the versatile platform is currently
broken in multiple ways. Most importantly, the ports do
not get mapped into the virtual address space at all.
Also, there is some amount of confusion between PCI I/O
space and other statically mapped MMIO registers in the
platform code:
* The __io_address() macro that is used to access the
platform register maps to the same __io macro that gets
used for I/O space.
* The IO_SPACE_LIMIT is set to a value that is much larger
than the total available space.
* The I/O resource of the PCI bus is set to the physical
address of the mapping, which is way outside of the
actual I/O space limit as well as the address range that
gets decoded by traditional PCI cards.
* No attempt is made to stay outside of the ISA port range
that some device drivers try access.
* No resource gets requested as a child of ioport_resource,
but an IORESOURCE_IO type mapping gets requested
as a child of iomem_resource.
This patch attempts to correct all of the above. This makes
it possible to use virtio-pci based virtual devices as well
as actual PCI cards including those with legacy ISA port
ranges like VGA.
Some of the issues seem to be duplicated on other platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[rob: update to 3.5-rc2 and io.h cleanup related changes]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* 'fixes' of git://github.com/hzhuang1/linux:
ARM: mmp: fix missing cascade_irq in irq handler
ARM: dts: update memory size on brownstone
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs compile warning fixes from Chris Mason.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: cast devid to unsigned long long for printk %llu
Btrfs: init old_generation in get_old_root
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile update from Chris Metcalf:
"This one-line bug fix unbreaks glibc robust mutexes (among other
things no doubt), from code merged in during the 3.5 merge window but
which we had been running internally at Tilera for almost a year."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: fix bug in get_user() for 4-byte values
|
|
Pull fbdev fixes from Florian Tobias Schandinat:
- two fixes for s3c-fb by Jingoo Han (including a fix for a potential
division by zero)
- a couple of randconfig fixes by Arnd Bergmann
- a cleanup for bfin_adv7393fb by Emil Goode
* tag 'fbdev-fixes-for-3.5-1' of git://github.com/schandinat/linux-2.6:
video: s3c-fb: fix possible division by zero in s3c_fb_calc_pixclk
video: s3c-fb: clear SHADOWCON register when clearing hardware window registers
drivers/tosa: driver needs I2C and SPI to compile
drivers/savagefb: use mdelay instead of udelay
video/console: automatically select a font
video/ili9320: do not mark exported functions __devexit
drivers/video: use correct __devexit_p annotation
video: bfin_adv7393fb: Convert to kstrtouint_from_user
|
|
The definition of 32-bit values in the 64-bit tilegx architecture is that
they should be sign-extended regardless of whether they are considered
signed or unsigned by the compiler. Accordingly, we need to use an
"ld4s" rather than "ld4u" to load and sign-extend for get_user().
This fixes glibc bug 14238 (see http://sourceware.org/bugzilla),
introduced during the 3.5 merge window.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
|
|
They aren't going anywhere, and probing on DDC can cause the panel to
blank briefly, so read them up front and cache them for later queries.
v2: fix potential NULL derefs in intel_dp_get_edid_modes and
intel_dp_get_edid (Jani)
copy full EDID length, including extension blocks (Takashi)
free EDID on teardown (Takashi)
v3: malloc a new EDID buffer that's big enough for the memcpy (Chris)
v4: change handling of NULL EDIDs, just preserve the NULL behavior
across detects and mode list fetches rather than trying to re-fetch
the EDID (Chris)
v5: be glad that Chris is around to remind me to hit C-x C-s before
committing.
References: https://bugs.freedesktop.org/show_bug.cgi?id=46856
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This reverts commit 092945e11c5b84f66dd08f0b87fb729715d377bc.
This commit prevents a DP screen from properly training the link.
Oddly enough it works, once the machine has been warm-booted with an
older kernel.
According to DP docs this _should_ have been the right precharge time.
Also, the commit that originally introduces this was just general snb
DP enabling and didn't mention any specific reason for this special
value. Whatever, trust the reporter that this makes things worse and
let's just revert it.
v2: Less spelling fail.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: "Wouter M. Koolen" <W.M.Koolen-Wijkstra@cwi.nl>
Buglink: https://lkml.org/lkml/2012/6/14/301
Cc: stable@vger.kernel.org (only for 3.4)
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The new oui probe has been missing these.
This issue has been introduce in
commit 0d198328538276c4459ef5de081e68ae60e6c4c2
Author: Adam Jackson <ajax@redhat.com>
Date: Mon May 14 16:05:47 2012 -0400
drm/i915/dp: Probe branch/sink OUIs
v2: Do the eDP vdd dance of simply not probing the OUI on eDP panels
as suggested by Chris Wilson.
v3: Fix up the error path fail - I suck.
Cc: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50808
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugreport: http://permalink.gmane.org/gmane.comp.video.dri.devel/69695
Tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This prevents the HDMI detect functions from poking at an eDP
connected panel, which can lead to trouble.
[danvet: Note that we have some other reports of DP vs. HDMI fighting,
but the general case is a much bigger fish to fry.]
References: https://bugs.freedesktop.org/show_bug.cgi?id=42278
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Required for streamout. Bump drm minor.
Marek v2: fix pkt->count check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
After recent changes HDMI code is ready to be enabled on DCE5. This
patch just changes conditions to execute already present code on DCE5.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Christian König <christian.koenig@amd.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The filed object_idr of struct drm_sis_private was introduced with
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=6de8a748881f1cd9d795454da2b6db616d5ca3d7 .
The idr_init(&dev->object_name_idr) is called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving object_idr
uninitialized. Correct this.
This patch was not tested because of lack of hardware.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The field obejct_idr of struct drm_via_private was introduced with the
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=77ee8f3825054f23b17e9c8f728f061defd86cdc .
In that patch idr_init(&dev->object_name_idr) was called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving the dev_priv->object_idr
uninitialized. To be more exact, the object_idr buffer is filled with zeros
because of kzalloc(), but the dev_priv->object_idr.lock spinlock can cause
system freeze at lib/idr.c:move_to_free_list() when spin_lock_irqsave()
is called on this spinlock.
The patch was tested on Clevo D4J, model D410J laptop, on the following
hardware, without AGP kernel module loaded:
# lspci -s 01:00.0 -n
01:00.0 0300: 1106:3108 (rev 01)
# lspci -s 01:00.0 -v
01:00.0 VGA compatible controller: VIA Technologies, Inc. K8M800/K8N800/K8N800A [S3 UniChrome Pro] (rev 01) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device 4702
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [70] AGP version 3.0
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
I finally got to test this code a bit more and hit the ttm
no reserved assert, so add the reservations around the pinning.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Not all asics have all rings, so make sure the ring is ready
before attempting to check it in the dynpm work handler.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=43367
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fix warnings on some architectures/configs (not on x86):
include/linux/vga_switcheroo.h:28:30: warning: 'struct pci_dev' declared inside parameter list [enabled by default]
include/linux/vga_switcheroo.h:28:30: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Takashi Iwai <tiwai@suse.de>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
