| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-3.6
Conflicts:
drivers/net/benet/be_main.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/net-next-2.6
|
|
|
|
TTY layer expects 0 if the ldisc->open operation succeeded.
Reported-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Like other mobile broadband device ethernet interfaces, mark the LG
VL600 with the 'wwan' devtype so userspace knows it needs additional
configuration via the AT port before the interface can be used.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unlike the standard case, disabled anti replay detection needs some
nontrivial extra treatment on ESN. RFC 4303 states:
Note: If a receiver chooses to not enable anti-replay for an SA, then
the receiver SHOULD NOT negotiate ESN in an SA management protocol.
Use of ESN creates a need for the receiver to manage the anti-replay
window (in order to determine the correct value for the high-order
bits of the ESN, which are employed in the ICV computation), which is
generally contrary to the notion of disabling anti-replay for an SA.
So return an error if an ESN state with disabled anti replay detection
is inserted for now and add the extra treatment later if we need it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As it is, we assign the outer modes output function to the dst entry
when we create the xfrm bundle. This leads to two problems on interfamily
scenarios. We might insert ipv4 packets into ip6_fragment when called
from xfrm6_output. The system crashes if we try to fragment an ipv4
packet with ip6_fragment. This issue was introduced with git commit
ad0081e4 (ipv6: Fragment locally generated tunnel-mode IPSec6 packets
as needed). The second issue is, that we might insert ipv4 packets in
netfilter6 and vice versa on interfamily scenarios.
With this patch we assign the inner mode output function to the dst entry
when we create the xfrm bundle. So xfrm4_output/xfrm6_output from the inner
mode is used and the right fragmentation and netfilter functions are called.
We switch then to outer mode with the output_finish functions.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 443457242beb (factorize sync-rcu call in
unregister_netdevice_many) mistakenly removed one test from dev_close()
Following actions trigger a BUG :
modprobe bonding
modprobe dummy
ifconfig bond0 up
ifenslave bond0 dummy0
rmmod dummy
dev_close() must not close a non IFF_UP device.
With help from Frank Blaschka and Einar EL Lueck
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Reported-by: Einar EL Lueck <ELELUECK@de.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip link add link eth2 eth2.103 type vlan id 103 gvrp on loose_binding on
ip link set eth2.103 up
rmmod tg3 # driver providing eth2
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffffa0030c9e>] garp_request_leave+0x3e/0xc0 [garp]
PGD 11d251067 PUD 11b9e0067 PMD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/virtual/net/eth2.104/ifindex
CPU 0
Modules linked in: tg3(-) 8021q garp nfsd lockd auth_rpcgss sunrpc libphy sg [last unloaded: x_tables]
Pid: 11494, comm: rmmod Tainted: G W 2.6.39-rc6-00261-gfd71257-dirty #580 HP ProLiant BL460c G6
RIP: 0010:[<ffffffffa0030c9e>] [<ffffffffa0030c9e>] garp_request_leave+0x3e/0xc0 [garp]
RSP: 0018:ffff88007a19bae8 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff88011b5e2000 RCX: 0000000000000002
RDX: 0000000000000000 RSI: 0000000000000175 RDI: ffffffffa0030d5b
RBP: ffff88007a19bb18 R08: 0000000000000001 R09: ffff88011bd64a00
R10: ffff88011d34ec00 R11: 0000000000000000 R12: 0000000000000002
R13: ffff88007a19bc48 R14: ffff88007a19bb88 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff88011fc00000(0063) knlGS:00000000f77d76c0
CS: 0010 DS: 002b ES: 002b CR0: 000000008005003b
CR2: 0000000000000000 CR3: 000000011a675000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process rmmod (pid: 11494, threadinfo ffff88007a19a000, task ffff8800798595c0)
Stack:
ffff88007a19bb36 ffff88011c84b800 ffff88011b5e2000 ffff88007a19bc48
ffff88007a19bb88 0000000000000006 ffff88007a19bb38 ffffffffa003a5f6
ffff88007a19bb38 670088007a19bba8 ffff88007a19bb58 ffffffffa00397e7
Call Trace:
[<ffffffffa003a5f6>] vlan_gvrp_request_leave+0x46/0x50 [8021q]
[<ffffffffa00397e7>] vlan_dev_stop+0xb7/0xc0 [8021q]
[<ffffffff8137e427>] __dev_close_many+0x87/0xe0
[<ffffffff8137e507>] dev_close_many+0x87/0x110
[<ffffffff8137e630>] rollback_registered_many+0xa0/0x240
[<ffffffff8137e7e9>] unregister_netdevice_many+0x19/0x60
[<ffffffffa00389eb>] vlan_device_event+0x53b/0x550 [8021q]
[<ffffffff8143f448>] ? ip6mr_device_event+0xa8/0xd0
[<ffffffff81479d03>] notifier_call_chain+0x53/0x80
[<ffffffff81062539>] __raw_notifier_call_chain+0x9/0x10
[<ffffffff81062551>] raw_notifier_call_chain+0x11/0x20
[<ffffffff8137df82>] call_netdevice_notifiers+0x32/0x60
[<ffffffff8137e69f>] rollback_registered_many+0x10f/0x240
[<ffffffff8137e85f>] rollback_registered+0x2f/0x40
[<ffffffff8137e8c8>] unregister_netdevice_queue+0x58/0x90
[<ffffffff8137e9eb>] unregister_netdev+0x1b/0x30
[<ffffffffa005d73f>] tg3_remove_one+0x6f/0x10b [tg3]
We should call vlan_gvrp_request_leave() from unregister_vlan_dev(),
not from vlan_dev_stop(), because vlan_gvrp_uninit_applicant()
is called right after unregister_netdevice_queue(). In batch mode,
unregister_netdevice_queue() doesn’t immediately call vlan_dev_stop().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit e67f88dd12f6 (net: dont hold rtnl mutex during netlink dump
callbacks) switched rtnl protection to RCU, but we forgot to adjust two
rcu_dereference() lockdep annotations :
inet_get_link_af_size() or inet_fill_link_af() might be called with
rcu_read_lock or rtnl held, so use rcu_dereference_rtnl()
instead of rtnl_dereference()
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rearrange xfrm4_dst_lookup() so that it works by calling a helper
function __xfrm_dst_lookup() that takes an explicit flow key storage
area as an argument.
Use this new helper in xfrm4_get_saddr() so we can fetch the selected
source address from the flow instead of from rt->rt_src
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use an explicit flow key and fetch it from there.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flow key is available, so fetch it from there.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already track and pass around the correct flow key,
so simply use it in udp_send_skb().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On input packets, rt->rt_src always equals ip_hdr(skb)->saddr
Anything that mangles or otherwise changes the IP header must
relookup the route found at skb_rtable(). Therefore this
invariant must always hold true.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This eliminates an access to rt->rt_src.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Revises the algorithm governing the sending of link request messages
to take into account the number of nodes each bearer is currently in
contact with, and to ensure more rapid rediscovery of neighboring nodes
if a bearer fails and then recovers.
The discovery object now sends requests at least once a second if it
is not in contact with any other nodes, and at least once a minute if
it has at least one neighbor; if contact with the only neighbor is
lost, the object immediately reverts to its initial rapid-fire search
timing to accelerate the rediscovery process.
In addition, the discovery object now stops issuing link request
messages if it is in contact with the only neighboring node it is
configured to communicate with, since further searching is unnecessary.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Augments TIPC's discovery object to track the number of neighboring nodes
having an active link to the associated bearer.
This means tipc_disc_update_link_req() becomes either one of:
tipc_disc_add_dest()
or:
tipc_disc_remove_dest()
depending on the code flow direction of things.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Augments TIPC's discovery object to send its initial neighbor discovery
request message as soon as the associated bearer is created, rather than
waiting for its first periodic timeout to occur, thereby speeding up the
discovery process. Also adds a check to suppress the initial request or
subsequent requests if the bearer is blocked at the time the request is
scheduled for transmission.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies bearer creation and deletion code to improve handling of
scenarios when a neighbor discovery object cannot be created. The
creation routine now aborts the creation of a bearer if its discovery
object cannot be created, and deletes the newly created bearer, rather
than failing quietly and leaving an unusable bearer hanging around.
Since the exit via the goto label really isn't a definitive failure
in all cases, relabel it appropriately.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Create a helper routine to enqueue a chain of sk_buffs to a link's
transmit queue. It improves readability and the new function is
anticipated to be used more than just once in the future as well.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Rework TIPC's message sending routines to take advantage of the total
amount of data value passed to it by the kernel socket infrastructure.
This change eliminates the need for TIPC to compute the size of outgoing
messages itself, as well as the check for an oversize message in
tipc_msg_build(). In addition, this change warrants an explanation:
- res = send_packet(NULL, sock, &my_msg, 0);
+ res = send_packet(NULL, sock, &my_msg, bytes_to_send);
Previously, the final argument to send_packet() was ignored (since the
amount of data being sent was recalculated by a lower-level routine)
and we could just pass in a dummy value (0). Now that the
recalculation is being eliminated, the argument value being passed to
send_packet() is significant and we have to supply the actual amount
of data we want to send.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Adds checks to TIPC's socket send routines to promptly detect and
abort attempts to send more than 66,000 bytes in a single TIPC
message or more than 2**31-1 bytes in a single TIPC byte stream request.
In addition, this ensures that the number of iovecs in a send request
does not exceed the limits of a standard integer variable.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Enhances existing checks on the discovery domain associated with a TIPC
bearer. A bearer can no longer be configured to accept links from itself
only (which would be pointless), or to nodes outside its own cluster
(since multi-cluster support has now been removed from TIPC). Also, the
neighbor discovery routine now validates link setup requests against the
configured discovery domain for the bearer, rather than simply ensuring
the requesting node belongs to the node's own cluster.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This allows them to be available for easy re-use in other places
and avoids trivial mistakes caused by "count the f's and 0's".
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies a TIPC send routine that did not discard the outgoing sk_buff
if it was not transmitted because of link congestion; this eliminates
the potential for buffer leakage in the many callers who did not clean up
the unsent buffer. (The two routines that previously did discard the unsent
buffer have been updated to eliminate their now-redundant clean up.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Sets the destination node field of an incoming multicast message
to the receiving node's network address before handing off the message
to each receiving port. This ensures that, in the event the destination
port returns the message to the sender, the sender can identify which
node the destination port belonged to.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Set the destination node and destination port fields of an outgoing
multicast message header to zero; this is necessary to ensure that
the receiving node can route the message properly if it was packed
into a bundle due to link congestion. (Previously, there was a chance
that the receiving node would send the unbundled message to a random
node & port, rather than processing the message itself.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Ensures that all outgoing data messages have the "name lookup scope"
field of their header set correctly; that is, named multicast messages
now specify cluster-wide name lookup, while messages not using TIPC
naming zero out the lookup field. (Previously, the lookup scope specified
for these types of messages was inherited from the last message sent
by the sending port.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Modifies the routine that fragments an existing message buffer to
use similar logic to that used when generating fragments from an iovec.
The routine now creates a complete chain of fragments and adds them to
the link transmit queue as a unit, so that the link sends all fragments
or none; this prevents the incomplete transmission of a fragmented
message that might otherwise result because of link congestion or
memory exhaustion. This change also ensures that the counter recording
the number of fragmented messages sent by the link is now incremented
only if the message is actually sent.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Eliminates code that restricts a link's counter of its fragmented
messages to a 16-bit value, since the counter value is automatically
restricted to this range when it is written into the message header.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Eliminates code that sets the link selector field in the header of
fragmented messages, since this information is never referenced.
(The unnecessary initialization was harmless as it was over-written
by the fragmented message identifier value before the fragments were
transmitted.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Eliminates optional code used to test TIPC's ability to recover
from lost broadcast messages. This code duplicates functionality
already provided by the network stack's QoS option "network emulator".
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Half of the #define entries in msg.h were down at the bottom
of the header, instead of up at the top before any of the static
inlines etc. Relocate them up to the top, to be consistent with
the other normal linux header file layout conventions.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Gets rid of unused constants defining the types used in routing
messages. These messages no longer exist in TIPC now that multicluster
and multizone support has been eliminated.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Removes comments in TIPC's message header include file that are
outdated and/or unnecessary. Also introduces short comments (or
supplements existing ones) to better describe several set of existing
symbolic constants.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
This patch reverts a2361c8735e07322023aedc36e4938b35af31eb0:
"[PATCH] netfilter: xt_conntrack: warn about use in raw table"
Florian Wesphal says:
"... when the packet was sent from the local machine the skb
already has ->nfct attached, and -m conntrack seems to do
the right thing."
Acked-by: Jan Engelhardt <jengelh@medozas.de>
Reported-by: Florian Wesphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The mask indicates the bits one wants to zero out, so it needs to be
inverted before applying to the original TOS field.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The IPv6 header is not zeroed out in alloc_skb so we must initialize
it properly unless we want to see IPv6 packets with random TOS fields
floating around. The current implementation resets the flow label
but this could be changed if deemed necessary.
We stumbled upon this issue when trying to apply a mangle rule to
the RST packet generated by the REJECT target module.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
DESCRIPTION
This patch tries to restore the initial init and cleanup
sequences that was before namspace patch.
Netns also requires action when net devices unregister
which has never been implemented. I.e this patch also
covers when a device moves into a network namespace,
and has to be released.
IMPLEMENTATION
The number of calls to register_pernet_device have been
reduced to one for the ip_vs.ko
Schedulers still have their own calls.
This patch adds a function __ip_vs_service_cleanup()
and an enable flag for the netfilter hooks.
The nf hooks will be enabled when the first service is loaded
and never disabled again, except when a namespace exit starts.
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
[horms@verge.net.au: minor edit to changelog]
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
If the sync daemons run in a name space while it crashes
or get killed, there is no way to stop them except for a reboot.
When all patches are there, ip_vs_core will handle register_pernet_(),
i.e. ip_vs_sync_init() and ip_vs_sync_cleanup() will be removed.
Kernel threads should not increment the use count of a socket.
By calling sk_change_net() after creating a socket this is avoided.
sock_release cant be used intead sk_release_kernel() should be used.
Thanks Eric W Biederman for your advices.
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
[horms@verge.net.au: minor edit to changelog]
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The optimizations in commit 255d0dc34068a976
(netfilter: x_table: speedup compat operations) assume that
xt_compat_add_offset is called once per rule.
ebtables however called it for each match/target found in a rule.
The match/watcher/target parser already returns the needed delta, so it
is sufficient to move the xt_compat_add_offset call to a more reasonable
location.
While at it, also get rid of the unused COMPAT iterator macros.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
commit 255d0dc34068a976 (netfilter: x_table: speedup compat operations)
made ebtables not working anymore.
1) xt_compat_calc_jump() is not an exact match lookup
2) compat_table_info() has a typo in xt_compat_init_offsets() call
3) compat_do_replace() misses a xt_compat_init_offsets() call
Reported-by: dann frazier <dannf@dannf.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
This patch fixes the missing initialization of the start time if
the timestamp support is enabled.
libnetfilter_conntrack/utils# conntrack -E &
libnetfilter_conntrack/utils# ./conntrack_create
tcp 6 109 ESTABLISHED src=1.1.1.1 dst=2.2.2.2 sport=1025 dport=21 packets=0 bytes=0 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=21 dport=1025 packets=0 bytes=0 mark=0 delta-time=1303296401 use=2
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Use the current logging styles.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert logging messages to more current styles.
Added -DDEBUG to Makefile to maintain current message logging.
This could be converted to a specific CONFIG_TULIP_DEBUG option.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the current more descriptive logging styles.
Add pr_fmt and remove PFX where appropriate.
Use netif_<level>, netdev_<level>
Indent a few blocks in xircom_cb where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the blocks that are guarded by #if DEBUG to
be #if defined DEBUG && DEBUG > 1 so that pr_debug
can be used later.
Remove enter/leave macros and uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6
|
