| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Expand the rq_addr field to allow it to contain larger addresses.
Specifically, we replace a 'sockaddr_in' with a 'sockaddr_storage', then
everywhere the 'sockaddr_in' was referenced, we use instead an accessor
function (svc_addr_in) which safely casts the _storage to _in.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sockaddr_storage will allow us to store arbitrary socket addresses in the
svc_deferred_req struct.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
for printing
There are loads of places where the RPC server assumes that the rq_addr fields
contains an IPv4 address. Top among these are error and debugging messages
that display the server's IP address.
Let's refactor the address printing into a separate function that's smart
enough to figure out the difference between IPv4 and IPv6 addresses.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sock_recvmsg
Clean-up: msg_name and msg_namelen are not used by sock_recvmsg, so don't
bother to set them in svc_recvfrom.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The remote peer's address won't change after the socket has been accepted. We
don't need to call ->getname on every incoming request.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rather than calling svc_sock_enqueue at the end of svc_setup_socket, we now
call it (via svc_sock_recieved) after calling svc_setup_socket at each call
site.
We do this because a subsequent patch will insert some code between the two
calls at one call site.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
with portmapper
Sometimes we need to create an RPC service but not register it with the local
portmapper. NFSv4 delegation callback, for example.
Change the svc_makesock() API to allow optionally creating temporary or
permanent sockets, optionally registering with the local portmapper, and make
it return the ephemeral port of the new socket.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
sockets
Currently in the RPC server, registering with the local portmapper and
creating "permanent" sockets are tied together. Expand the internal APIs to
allow these two socket characteristics to be separately specified.
This will be externalized in the next patch.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Aurelien Charbon <aurelien.charbon@ext.bull.net>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I think the following patch should go into the kernel, until the ISDN/CAPI
guys create the real fix for this issue.
The issue is a concurrency issue with some internal CAPI data structure
which can crash the kernel.
On my FritzCard DSL with the AVM driver it crashes about once a day without
this workaround patch. With this workaround patch it's rock-stable (at
least on UP, but I don't see why this shouldn't work on SMP as well. But
maybe I'm missing something.)
This workaround is kind of a sledgehammer which inserts a global lock to
wrap around all the critical sections. Of course, this is a scalability
issue, if you have many ISDN/CAPI cards. But it prevents a crash. So I
vote for this fix to get merged, until people come up with a better
solution. Better have a stable kernel that's less scalable, than a
crashing and useless kernel.
This bug is in the kernel since 2.6.15 (at least).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Kai Germaschewski <kai.germaschewski@gmx.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rename the macro CONFIG_HISAX_HFC4S8S_PCIMEM to simply HISAX_HFC4S8S_PCIMEM so
that it no longer resembles a user-settable kernel config macro.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Based on advice from K. Keil, get rid of remaining traces of defunct test
emulator for HISAX.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Based on advice from K. Keil, rename the special debug option
CONFIG_SERIAL_NOPAUSE_IO to ELSA_SERIAL_NOPAUSE_IO so it no longer resembles a
user-selectable kernel config option.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Rename some of the debugging macros for ISDN AVM so that they don't resemble
kernel config settings, as they're primarily for author debugging instead.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace misspelled CONFIG_HISAX_QUADRO with CONFIG_HISAX_SCT_QUADRO.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add proper prototypes in a header file for global code under
drivers/isdn/sc/.
Since the GNU C compiler is now able do tell us that caller and callee
disagreed about the number of arguments of setup_buffers(), this patch
also fixes this bug.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- add functions prototypes for some global functions to header files
- remove unneeded "extern"s from some function prototypes
You might note that this patch results in a new warning - that's due to the
fact that with a proper prototype gcc is able to discover a broken
work_struct conversion.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add correct prototypes in header files for global functions and variables.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Arch-neutral GPIO calls for S3C24xx.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Arch-neutral GPIO calls for SA-1100.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Arch-neutral GPIO calls for PXA.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a first cut at making the AT91 code use the generic GPIO calls.
Note that the original AT91 GPIO calls merged the "mux pin as GPIO" and "set
GPIO direction" functionality into one API call, contrary to what's specified
as a cross-platform portable model. So this involved a few non-inlinable
functions.
[akpm@osdl.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This teaches OMAP how to implement the cross-platform GPIO interfaces.
[akpm@osdl.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This defines a simple and minimalist programming interface for GPIO APIs:
- Documentation/gpio.txt ... describes things (read it)
- include/asm-arm/gpio.h ... defines the ARM hook, which just punts
to <asm/arch/gpio.h> for any implementation
- include/asm-generic/gpio.h ... implement "can sleep" variants as calling
the normal ones, for systems that don't handle i2c expanders.
The immediate need for such a cross-architecture API convention is to support
drivers that work the same on AT91 ARM and AVR32 AP7000 chips, which embed many
of the same controllers but have different CPUs. However, several other users
have been reported, including a driver for a hardware watchdog chip and some
handhelds.org multi-CPU button drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Eric Wollesen ported the Bluesmoke Memory Controller driver for the Intel
5000X/V/P (Blackford/Greencreek) chipset to the in kernel EDAC model.
This patch incorporates those required changes to the edac_mc.c and edac_mc.h
core files by added new Fully Buffered DIMM interface to the EDAC Core module.
Signed-off-by: eric wollesen <ericw@xmtp.net>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is an attempt of providing an interface for memory scrubbing control in
EDAC.
This patch modifies the EDAC Core to provide the Interface for memory
controller modules to implment.
The following things are still outstanding:
- K8 is the first implemenation,
The patch provide a method of configuring the K8 hardware memory scrubber
via the 'mcX' sysfs directory. There should be some fallback to a generic
scrubber implemented in software if the hardware does not support
scrubbing.
Or .. the scrubbing sysfs entry should not be visible at all.
- Only works with SDRAM, not cache,
The K8 can scrub cache and l2cache also - but I think this is not so
useful as the cache is busy all the time (one hopes).
One would also expect that cache scrubbing requires hardware support.
- Error Handling,
I would like that errors are returned to the user in "terms of file
system".
- Presentation,
I chose Bandwidth in Bytes/Second as a representation of the scrubbing
rate for the following reasons:
I like that the sysfs entries are sort-of textual, related to something
that makes sense instead of magical values that must be looked up.
"My People" wants "% main memory scrubbed per hour" others prefer "%
memory bandwidth used" as representation, "bandwith used" makes it easy to
calculate both versions in one-liner scripts.
If one later wants to scrub cache, the scaling becomes wierd for K8
changing from "blocks of 64 byte memory" to "blocks of 64 cache lines" to
"blocks of 64 bit". Using "bandwidth used" makes sense in all three cases,
(I.M.O. anyway ;-).
- Discovery,
There is no way to discover the possible settings and what they do
without reading the code and the documentation.
*I* do not know how to make that work in a practical way.
- Bugs(??),
other tools can set invalid values in the memory scrub control register,
those will read back as '-1', requiring the user to reset the scrub rate.
This is how *I* think it should be.
- Afflicting other areas of code,
I made changes to edac_mc.c and edac_mc.h which will show up globally -
this is not nice, it would be better that the memory scrubbing fuctionality
and interface could be entirely contained within the memory controller it
applies to.
Frithiof Jensen
edac_mc.c and its .h file is a CORE helper module for EDAC
driver modules. This provides the abstraction for device specific
drivers. It is fine to modify this CORE to provide help for
new features of the the drivers
doug thompson
Signed-off-by: Frithiof Jensen <frithiof.jensen@ericson.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This fix/change returns the offset into the page for the ce/ue error, instead
of just 0. The e752x dram controller reads 34:6 of the linear address with
the error.
Signed-off-by: Mike Chan <mikechan@google.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The reading of the DRA registers should be a byte at a time (one register at a
time) instead of 4 bytes at a time (four registers). Reading a dword at a
time retrieves erroneous information from all but the first register. A
change was made to read in each register in a loop prior to using the data in
those registers.
Signed-off-by: Brian Pomerantz <bapper@mvista.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The fatal vs. non-fatal mask for the sysbus FERR status is incorrect
according to the E7520 datasheet. This patch corrects the mask to correctly
handle fatal and non-fatal errors.
Signed-off-by: Brian Pomerantz <bapper@mvista.com>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that I have changed all of the in-tree users remove the old version of
these functions. This should make it clear to any out of tree users that they
should be using kill_pgrp kill_pgrp_info or __kill_pgrp_info instead.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that I have changed all of the users remove the old version of these
functions. This should be a clear hint to any out of tree users that they
should use do_each_pid_task and while_each_pid_task for new code.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There isn't any real advantage to this change except that it allows the old
functions to be removed. Which is easier on maintenance and puts the code in
a more uniform style.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Of kernel subsystems that work with pids the tty layer is probably the largest
consumer. But it has the nice virtue that the assiation with a session only
lasts until the session leader exits. Which means that no reference counting
is required. So using struct pid winds up being a simple optimization to
avoid hash table lookups.
In the long term the use of pid_nr also ensures that when we have multiple pid
spaces mixed everything will work correctly.
Signed-off-by: Eric W. Biederman <eric@maxwell.lnxi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Every call to is_orphaned_pgrp passed in process_group(current) which is racy
with respect to another thread changing our process group. It didn't bite us
because we were dealing with integers and the worse we would get would be a
stale answer.
In switching the checks to use struct pid to be a little more efficient and
prepare the way for pid namespaces this race became apparent.
So I simplified the calls to the more specialized is_current_pgrp_orphaned so
I didn't have to worry about making logic changes to avoid the race.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Modify has_stopped_jobs and will_become_orphan_pgrp to use struct pid based
process groups. This reduces the number of hash tables looks ups and paves
the way for multiple pid spaces.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To properly implement a pid namespace I need to deal exclusively in terms of
struct pid, because pid_t values become ambiguous.
To this end session_of_pgrp is transformed to take and return a struct pid
pointer. To avoid the need to worry about reference counting I now require my
caller to hold the appropriate locks. Leaving callers repsonsible for
increasing the reference count if they need access to the result outside of
the locks.
Since session_of_pgrp currently only has one caller and that caller simply
uses only test the result for equality with another process group, the locking
change means I don't actually have to acquire the tasklist_lock at all.
tiocspgrp is also modified to take and release the lock. The logic there is a
little more complicated but nothing I won't need when I convert pgrp of a tty
to a struct pid pointer.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The goal is to remove users of the old signal helper functions so they can be
removed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I am slowly moving to a model where all process killing is struct pid based
instead of pid_t based. The sunos compatibility code is one of the last users
of the old pid_t based kill_pg in the kernel. By being complete I allow for
the future removal of kill_pg from the kernel, which will ensure I don't miss
something.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 24ec839c431eb79bb8f6abc00c4e1eb3b8c4d517 while fixing the locking for
signal->tty got the locking wrong for signal->session. This places our
accesses of signal->session back under the tasklist_lock where they belong.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The code to look at tty_old_pgrp and send SIGHUP and SIGCONT when it is
present only executes when disassociate_ctty is called from do_exit. Make
this clear by adding an explict on_exit check, and explicitly setting
tty_old_pgrp to 0.
In addition fix the locking by reading tty_old_pgrp under the siglock.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The aim of this patch set is to start wrapping up the struct pid conversions.
As such this patchset culminates with the removal of kill_pg, kill_pg_info,
__kill_pg_info, do_each_task_pid, and while_each_task_pid.
kill_proc, daemonize, and kernel_thread are still in my sights but there is
still work to get to them.
The first three are basic cleanups around disassociate_ctty, while working on
converting it I found several issues. tty_old_pgrp can be a tricky concept to
wrap your head around.
1 tty: Make __proc_set_tty static.
2 tty: Clarify disassociate_ctty
3 tty: Fix the locking for signal->session in disassociate_ctty
These just stop using the old helper functions.
4 signal: Use kill_pgrp not kill_pg in the sunos compatibility code.
5 signal: Rewrite kill_something_info so it uses newer helpers.
Then the grind to convert the tty layer and all of it's helper functions to
struct pid.
6 pid: Make session_of_pgrp use struct pid instead of pid_t.
7 pid: Use struct pid for talking about process groups in exit.c
8 pid: Replace is_orphaned_pgrp with is_current_pgrp_orphaned
9 tty: Update the tty layer to work with struct pid.
A final helper function update.
10 pid: Replace do/while_each_task_pid with do/while_each_pid_task
And the removal of the functions that are now unused.
11 pid: Remove now unused do_each_task_pid and while_each_task_pid
12 pid: Remove the now unused kill_pg kill_pg_info and __kill_pg_info
All of these should be fairly simple and to the point.
This patch:
Currently all users of __proc_set_tty are in tty_io.c so make the function
static.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This morning I needed to read a Minix V3 filesystem, but unfortunately my
2.6.19 did not support that, and neither did the downloaded 2.6.20rc4.
Fortunately, google told me that Daniel Aragones had already done the work,
patch found at http://www.terra.es/personal2/danarag/
Unfortunaly, looking at the patch was painful to my eyes, so I polished it
a bit before applying. The resulting kernel boots, and reads the
filesystem it needed to read.
Signed-off-by: Daniel Aragones <danarag@gmail.com>
Signed-off-by: Andries Brouwer <aeb@cwi.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is adds a simple SPI EEPROM driver, providing access to the EEPROM
through sysfs much like the I2C "eeprom" driver ... except this driver
supports write access, and multiple EEPROM sizes.
From: "Tuppa, Walter" <walter.tuppa@siemens.com>
Since I have EEPROMs on SPI with different address sizing, I made some
changes to your at25.c to support them. Works perfectly. (Also includes a
small bugfix for the "what size address" test.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Walter Tuppa <walter.tuppa@siemens.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds a new "wakealarm" sysfs attribute to RTC class devices which support
alarm operations and are wakeup-capable:
- It reads as either empty, or the scheduled alarm time as seconds
since the POSIX epoch. (That time may already have passed, since
nothing currently enforces one-shot alarm semantics.)
- It can be written with an alarm time in the future, again seconds
since the POSIX epoch, which enables the alarm.
- It can be written with an alarm time not in the future (such as 0,
the start of the POSIX epoch) to disable the alarm.
Usage examples (some need GNU date) after "cd /sys/class/rtc/rtcN":
alarm after 10 minutes:
# echo $(( $(cat since_epoch) + 10 * 60 )) > wakealarm
alarm tuesday evening 10pm:
# date -d '10pm tuesday' "+%s" > wakealarm
disable alarm:
# echo 0 > wakealarm
This resembles the /proc/acpi/alarm file in that nothing happens when the
alarm triggers ... except possibly waking the system from sleep. It's also
like that in a nasty way: not much can be done to prevent one task from
clobbering another task's alarm settings.
It differs from that file in that there's no in-kernel date parser.
Note that a few RTCs ignore rtc_wkalrm.enabled when setting alarms, or aren't
set up correctly, so they won't yet behave with this attribute.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This clarifies some aspects of the SPI programming interface, based on
feedback from Hans-Peter Nilsson. The in-memory representation of words is
right-aligned, so for example a twelve bit word is stored using sixteen bits
with four undefined bits in the MSB. And controller drivers must reject
protocol tweaking modes they do not support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'd like to assign NULL to kfree()d members of a structure. I can't do
that without ugly casting (see the PXA patch) when the structure pointed to
is const-qualified. I don't really see a reason why the cleanup method
isn't allowed to alter the object it should clean up. :-)
No, I didn't test the PXA patch, but I verified that the NULL-assignment
doesn't stop me from doing rmmod/insmodding my own spi_bitbang-based
driver.
Signed-off-by: Hans-Peter Nilsson <hp@axis.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A small bug-fix for spi_bitbang: it must always call the setup_transfer
function via the overridable pointer, not assume that its
spi_bitbang_setup_transfer is sufficient. Otherwise, if all options in the
transfers are default (0), the overrided function will never be called.
Granted, the function replacing it must call spi_bitbang_setup_transfer,
but it might also have other important things to do, even if the second
argument (the spi_transfer) is NULL. Tested together with the other
patches on the spi_crisv32_sser and spi_crisv32_gpio drivers (not yet in
the kernel, will IIUC be submitted as part of the usual
arch-maintainer-pushes).
Signed-off-by: Hans-Peter Nilsson <hp@axis.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
