1 files changed, 74 insertions, 0 deletions
diff --git a/xc/programs/Xserver/hw/xfree86/drivers/siliconmotion/README b/xc/programs/Xserver/hw/xfree86/drivers/siliconmotion/README
new file mode 100644
index 000000000..3e8b8b264
--- /dev/null
+++ b/xc/programs/Xserver/hw/xfree86/drivers/siliconmotion/README
@@ -0,0 +1,74 @@
+What works:
+- Supports 8bpp, 16bpp and 24bpp. Heavy testing on SM720.
+
+XCONFIG options:
+
+The driver supports quite a few different XConfig options, which can
+be used to tune the driver and improve performance. Without any options,
+the driver will use conservative settings which should work on most
+hardware. Large improvements in performance are possible by selecting
+the proper options, which will probably work on most systems.
+
+Cursor:
+
+- "hwcursor" "off" behaves exactly like "swcursor".  Default: "on"
+- "swcursor" will disable the HW Cursor.  HW Cursor is used by default and
+	no option is needed to enable it.
+
+Display:
+
+- "ShadowFB"  Use shadow framebuffer.  Default: off.
+- "Rotate" "cw" | "ccw"  Rotate the screen CW - clockwise or CCW - counter
+    clockwise.  Uses ShadowFB.  Default: no rotation.
+
+Overlays:
+
+- "VideoKey"  Set chroma key for video.  Default:  Off blue.
+- "ByteSwap"  Turn on YUV byte swapping.  Defaul: off.
+
+Video memory:
+
+- "set_mclk" sets the memory clock, format is:
+	Option "set_mclk" "50000"
+	in the XF86Config file.  Valid values are any
+	integer <= 100000, where 100000 == 100 MHz.
+
+Acceleration and graphic engine:
+
+- "NoAccel" turns off all acceleration
+- "fifo_aggressive", "fifo_moderate" and "fifo_conservative" alter the settings
+	for the threshold at which the pixel FIFO takes over the internal
+	memory bus to refill itself. The smaller this threshold, the better
+	the acceleration performance of the card. You may try the fastest
+	setting ("aggressive") and move down if you encounter pixel corruption.
+	The optimal setting will probably depend on dot-clock and on color
+	depth. Note that specifying any of these options will also alter other
+	memory settings which should increase performance, so you should at
+        least use "fifo_conservative" (this uses the chip defaults).
+- Common XAA acceleration options to disable primitives for test purposes:
+	"XaaNoScreenToScreenCopy"
+	"XaaNoSolidFillRect"
+	"XaaNoColor8x8PatternFillRect"
+	"XaaNoImageWriteRect"
+	"XaaNoPixmapCache"
+
+PCI bus:
+
+- "pci_burst" will enable PCI burst mode. This should work on all but a
+	few "broken" PCI chipsets, and will increase performance.  Option may
+	take a parameter "on", "off", "yes", etc...
+- "pci_retry" will allow the driver to rely on PCI Retry to program the
+	ViRGE registers. "pci_burst" must be enabled for this to work.
+	This will increase performance, especially for small fills/blits,
+        because the driver does not have to poll the ViRGE before sending it
+        commands to make sure it is ready. It should work on most
+        recent PCI chipsets.
+
+Debug:
+
+- "ShowCache"  Enable or disable viewing offscreen cache memory.  A
+    development debug option.  Default: off.
+
+Header:   //Mercury/Projects/archives/XFree86/4.0/README.-arc   1.2   14 Sep 2000 12:28:36   Frido  $
+
+$XFree86: xc/programs/Xserver/hw/xfree86/drivers/siliconmotion/README,v 1.1 2000/11/28 20:59:18 dawes Exp $