| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In power_supply_show_property() routine, we call ->get_property() conditionally
and should check for failure in that case only. There is no point comparing
'ret' for errors when 'ret' is surely zero.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Usually PMIC's come with coulomb counting mechanism which can be
used to implement a Fuel Gauginig solution in Software itself.
One of key input to these SW Fuel Gauge solutioons is the boot up
parameters like boot voltage and boot current.
This patch adds the VOLTAGE_BOOT and CURRENT_BOOT power supply attributes
to report bootup voltage and current.
This patch also adds CALIBRATE power supply attribute which useful is
for calibrating the battery/coulomb counter.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add new power supply properties for input current, charge termination
current, min and max temperature
POWER_SUPPLY_PROP_TEMP_MIN - minimum operatable temperature
POWER_SUPPLY_PROP_TEMP_MAX - maximum operatable temperature
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT - input current limit programmed
by charger. Indicates the input current for a charging source.
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT - Charge termination current used
to detect the end of charge condition
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The usage of strict_strtol() is not preferred, because strict_strtol() is
obsolete. Thus, kstrtol() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
As most of the charger chips come with two kinds of safety features
related to timing:
1. Watchdog Timer (interms of seconds/mins)
2. Safety Timer (interms of hours)
This patch adds these to fault causes in POWER_SUPPLY_PROP_HEALTH_* enums
so that whenever there is either watchdog timeout or safety timer timeout
driver could notify the user space accurately about the fault and will
also be helpful for debug.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Add support for power supply attributes CHARGE_CONTROL_LIMIT
and CHARGE_CONTROL_LIMIT_MAX.
These new attributes will enable the user space to implement
custom charging algorithms based on platform state.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
There are different types of chargers avalibale like AC, Solar, USB,
etc.. Even in USB we have different types SDP/DCP/CDP/ACA and all these
chargers have different o/p ratings. For example SDP supports only 500mA
of charge current whereas AC charger can support upto 8A or more.
Similarly batteries also come with charge current and voltage ratings
and these ratings vary depending on its capacity and the technology
used.
This patch adds two new power supply properties
CONSTANT_CHARGE_CURRENT_MAX and CONSTANT_CHARGE_CURRENT_MAX.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
It is possible that users can use non-standard chargers or use invalid
batteries especially with mobile devices.
This patch adds a new power supply property called 'AUTHENTIC' to
indicate this to the user(user space).
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Minimum and maximum alerts on power supply properties will help or allow
the user space to "proactively" create policies like connect/disconnect
charger or stop/start the user apps based on capacity or temperature
parameters.
These parameters can be used to avoid unnecessary polling from user space
and even from kernel space if the underlying HW can support INT triggers
(ex: max17042/47).
This patch adds the following power supply alert type properties:
CAPACITY_ALERT_MIN
CAPACITY_ALERT_MAX
TEMP_ALERT_MIN
TEMP_ALERT_MAX
TEMP_AMBIENT_ALERT_MIN
TEMP_AMBIENT_ALERT_MAX
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Constant Charge Current(CC) is charging parameter which limit the
maximum current which can be pumped into the battery during charge cycle.
Constant Charge Voltage(CV) is also charging parameter which limit the
maximum voltage that battery can reach during charge cycle.
It is very common practice that at low or high temperatures we
do not charge the batteries upto it's fullest charge voltage
to avoid battery and user safety issues.
These sysfs properties will be useful for debug and to implement
certain user space policies like "Charging limited due to OverTemp".
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This adds a new sysfs file called 'voltage_ocv' which gives the
Open Circuit Voltage of the battery.
This property can be used for platform shutdown policies and
can be useful for initial capacity estimations.
Note: This patch is generated against linux-next branch.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
For files that are actively using linux/device.h, make sure
that they call it out. This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.
Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered. This ensures we don't introduce
build regressions into the git history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
|
|
For the default value of power supply type, "unknown" is added.
With default prop value, supply type property can be displayed
as default - "Unknown".
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This adds a "scope" attribute to a power_supply, which indicates how
much of the system it powers. It appears in sysfs as "scope" or in
the uevent file as POWER_SUPPLY_SCOPE=. There are presently three
possible values:
Unknown - unknown power topology
System - the power supply powers the whole system
Device - it powers a specific device, or tree of devices
A power supply which doesn't have a "scope" attribute should be assumed to
have "System" scope.
In general, usermode should assume that loss of all System-scoped power
supplies will power off the whole system, but any single one is sufficient
to power the system.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Richard Hughes <richard@hughsie.com>
|
|
It was actually getting this before by a tangled mess of implict
includes that is going to be cleaned up. Fix it now, so we don't
get this after the cleanup.
power_supply_sysfs.c: In function ‘power_supply_attr_is_visible’:
power_supply_sysfs.c:184: error: ‘S_IRUSR’ undeclared (first use in this function)
power_supply_sysfs.c:184: error: (Each undeclared identifier is reported only once
power_supply_sysfs.c:184: error: for each function it appears in.)
power_supply_sysfs.c:184: error: ‘S_IRGRP’ undeclared (first use in this function)
power_supply_sysfs.c:184: error: ‘S_IROTH’ undeclared (first use in this function)
power_supply_sysfs.c:196: error: ‘S_IWUSR’ undeclared (first use in this function)
make[3]: *** [drivers/power/power_supply_sysfs.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Fix format warning:
drivers/power/power_supply_sysfs.c:82: warning: format '%d' expects type 'int', but argument 4 has type 'ssize_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Don't tell the system about the battery charger if it's not enabled, we
can reasonably assume that if the charger is not enabled then no battery
will ever be connected so reporting state is at best going to waste time
and at worst going to cause confusing information in the UI.
For simplicity and robustness we continue to register and handle interrupts
from the charger.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Sometimes a driver can not report a meaningful value for a certain property
and returns -ENODATA.
Currently when generating a uevent and a property return -ENODATA it is
treated as an error an no uevent is generated at all. This is not an
desirable behavior.
This patch adds a special case for -ENODATA and ignores properties which
return this error code when generating the uevent.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
|
|
USB only gives the maximum current allowed to draw.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This adds power supply types for USB chargers defined in
Battery Charging Specification 1.1.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Commit 5f487cd34f4337f9bc27ca19da72a39d1b0a0ab4 (power_supply: Use
attribute groups) causes a regression the power supply core does not
export the 'type' attribute anymore.
POWER_SUPPLY_PROP_TYPE is handled by the power supply core without the
low-level driver, so power_supply_attr_is_visible() must always return
the entry as readable.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This patch adds support for writeable power supply properties and
exposes them as writeable to sysfs.
A power supply implementation must implement two new function calls in
order to use that feature:
int set_property(struct power_supply *psy,
enum power_supply_property psp,
const union power_supply_propval *val);
int property_is_writeable(struct power_supply *psy,
enum power_supply_property psp);
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Cc: Len Brown <len.brown@intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Matt Reimer <mreimer@vpop.net>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This fixes a race between power supply device and initial
attributes creation, plus makes it possible to implement
writable properties.
[Daniel Mack - removed superflous return statement
and dropped .mode attribute from POWER_SUPPLY_ATTR]
Suggested-by: Greg KH <gregkh@suse.de>
Suggested-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There are cases when some device can not report any meaningful value,
e.g. TWL4030 charger can report voltage only when charging is
active.
In these cases drivers will return -ENODATA, and we shouldn't flood
kernel log with error messages.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
This adds a new sysfs file called 'charge_type' which displays the
type of charging (unknown, n/a, trickle charge, or fast charging).
This allows things like battery diagnostics to determine what the
battery/EC is doing without resorting to changing the 'status' sysfs
output.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This reverts commit 8efe444038a205e79b38b7ad03878824901849a8 and
4cbc76eadf56399cd11fb736b33c53aec9caab8c.
Richard@laptop.org was apparently using CAPACITY_LEVEL for debugging
battery/EC problems, and was upset that it was removed. This readds it.
Conflicts:
Documentation/power_supply_class.txt
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
ACPI has smart batteries, which work in units of energy and measure
rate of (dis)charge as power, thus it is not appropriate to export it
as a current_now. Current_now will still be exported to allow
for userland applications to match.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Some systems are able to report problems with batteries being under
temperature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Tejun's commit 7b595756ec1f49e0049a9e01a1298d53a7faaa15 made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
drivers/power/Kconfig
drivers/power/Makefile
|
|
Commit 54d29ad33e3483bcc7ca433a21cf294854e5154a (Power Supply: fix race
in device_create) introduced a race in power_supply_uevent. Previously it
checked that power_supply is available by checking for dev->driver_data.
But now dev->driver_data is set before power_supply->dev is initialised.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This adds PROP_CHARGE_COUNTER to the power supply class (documenting it
as well). The OLPC battery driver uses this for spitting out its ACR
values (in uAh). We have some rounding errors (the data sheet claims
416.7, the math actually works out to 416.666667, so we're forced to
choose between overflows or precision loss. I chose precision loss,
and stuck w/ data sheet values), but I don't think anyone will care
that much.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (112 commits)
ACPI: fix build warning
Revert "cpuidle: build fix for non-x86"
ACPI: update intrd DSDT override console messages
ACPI: update DSDT override documentation
ACPI: Add "acpi_no_initrd_override" kernel parameter
ACPI: its a directory not a folder....
ACPI: misc cleanups
ACPI: add missing prink prefix strings
ACPI: cleanup acpi.h
ACPICA: fix CONFIG_ACPI_DEBUG_FUNC_TRACE build
ACPI: video: Ignore ACPI video devices that aren't present in hardware
ACPI: video: reset brightness on resume
ACPI: video: call ACPI notifier chain for ACPI video notifications
ACPI: create notifier chain to get hotkey events to graphics driver
ACPI: video: delete unused display switch on hotkey event code
ACPI: video: create "brightness_switch_enabled" modparam
cpuidle: Add a poll_idle method
ACPI: cpuidle: Support C1 idle time accounting
ACPI: enable MWAIT for C1 idle
ACPI: idle: Fix acpi_safe_halt usages and interrupt enabling/disabling
...
|
|
This commit:
commit 8efe444038a205e79b38b7ad03878824901849a8
Author: Andres Salomon <dilinger@queued.net>
Date: Wed Dec 12 14:12:56 2007 -0500
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
Removed CAPACITY_LEVEL from every other code, leaving the array with sysfs
attributes with one more entry than the number of enums in power_supply.h.
This leads to some attributes containing the value of the attribute right
after it. For example, temp_ambient would have the value of
time_to_empty_now. In my case, I had time_to_full_avg have the value which
should be in model_name, when the former was usually empty.
Cc: Andres Salomon <dilinger@debian.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
egrep serial /proc/acpi/battery/BAT0/info
serial number: 32090
serial number can tell you from the imminent danger
of beeing set on fire.
Signed-off-by: maximilian attems <max@stro.at>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add LiMn (one of the most common for small non-rechargable batteries)
battery technology and voltage_min/_max properties support.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
|
|
In power_supply_create_attrs(), we create static attributes as referenced
by power_supply_static_attrs[i]. After that, if we fail, we unregister
via power_supply_static_attrs[psy->properties[i]]. This is incorrect, as
psy->properties has absolutely no bearing on static attribs. This patch
fixes it to unregister the correct attrib.
Another line which was unnecessarily line wrapped is also unwrapped.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The CAPACITY_LEVEL stuff defines various levels of charge; however, what
is the difference between them? What differentiates between HIGH and NORMAL,
LOW and CRITICAL, etc?
As it appears that these are fairly arbitrary, we end up making such policy
decisions in the kernel (or in hardware). This is the sort of decision that
should be made in userspace, not in the kernel.
If the hardware does not support _CAPACITY and it cannot be easily calculated,
then perhaps the driver should register a custom CAPACITY_LEVEL attribute;
however, userspace should not become accustomed to looking for such a thing,
and we should certainly not encourage drivers to provide CAPACITY_LEVEL
stubs.
The following removes support for POWER_SUPPLY_PROP_CAPACITY_LEVEL. The
OLPC battery driver is the only driver making use of this, so it's
removed from there as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
for its global functions.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
|
|
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Need to null terminate environment. Found by inspection
while looking for similar problems to platform uevent bug
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
|
|
Per Jeff Garzik request.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
|
|
This class is result of "external power" and "battery" classes merge,
as suggested by David Woodhouse. He also implemented uevent support.
Here how userspace seeing it now:
# ls /sys/class/power\ supply/
ac main-battery usb
# cat /sys/class/power\ supply/ac/type
AC
# cat /sys/class/power\ supply/usb/type
USB
# cat /sys/class/power\ supply/main-battery/type
Battery
# cat /sys/class/power\ supply/ac/online
1
# cat /sys/class/power\ supply/usb/online
0
# cat /sys/class/power\ supply/main-battery/status
Charging
# cat /sys/class/leds/h5400\:red-left/trigger
none h5400-radio timer hwtimer ac-online usb-online
main-battery-charging-or-full [main-battery-charging]
main-battery-full
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
