summaryrefslogtreecommitdiff
path: root/drivers/net/bnx2x_main.c
AgeCommit message (Collapse)AuthorFilesLines
2009-07-21bnx2x: Version 1.48.113-1Eilon Greenstein1-2/+2
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21bnx2x: Supporting BCM8727 PHYEilon Greenstein1-14/+53
Adding support for BCM8727 - a dual port SFP+ PHY. That includes verification of the optic module vendor and part number - the list of approved modules resides on the nvram and the module is verified by the FW. Since not all users would like to use this verification feature, it can be disabled. The default behavior is to issue a warning if the module is not approved, but still allow using it - but it is also possible to disable the link if the module is not approved. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21bnx2x: Update vlan_featuresEilon Greenstein1-2/+17
As noted by Or Gerlitz <ogerlitz@Voltaire.com>, the vlan_features was not updated Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21bnx2x: SMP-safe inter_semEilon Greenstein1-1/+9
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21bnx2x: Adding some mmiowbEilon Greenstein1-0/+17
Signed-off-by: Vlad Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21bnx2x: Fan failure early detectionEilon Greenstein1-0/+5
Check if fan failure happened before the driver was loaded and notify the user Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21bnx2x: Fan failureEilon Greenstein1-37/+75
Setup fan failure for different PHY types or according to nvram settings Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21bnx2x: Stop management traffic in loopback testEilon Greenstein1-0/+11
Since management traffic cannot go on the wire while configured to loopback, simply stop it to avoid race condition when the MAC is set to loopback in the middle of a packet Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05bnx2x: Fix the maximal values of coalescing timeouts.Eilon Greenstein1-4/+4
This patch properly defines the maximum values for rx/tx coalescing timeouts. Signed-off-by: Vlad Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05bnx2x: Disable HC coalescing when setting timeout to zero.Eilon Greenstein1-2/+2
Problem reported by Flavio Leitner <fleitner@redhat.com>: When setting rx/tx coalescing timeout to the values less than 12 traffic was stopped. The FW supports coalescing in 12us granularity, and so value of less then 12 should be interpreted as disabling coalescing Signed-off-by: Vlad Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-30bnx2x: Fix the behavior of ethtool when ONBOOT=noNaohiro Ooiwa1-1/+9
This is the same fix as commit 7959ea254ed18faee41160b1c50b3c9664735967 ("bnx2: Fix the behavior of ethtool when ONBOOT=no"), but for bnx2x: -------------------- When configure in ifcfg-eth* is ONBOOT=no, the behavior of ethtool command is wrong. # grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2 ONBOOT=no # ethtool eth2 | tail -n1 Link detected: yes I think "Link detected" should be "no". -------------------- Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29net: dont update dev->trans_start in 10GB driversEric Dumazet1-1/+0
Followup of commits 9d21493b4beb8f918ba248032fefa393074a5e2b and 08baf561083bc27a953aa087dd8a664bb2b88e8e (net: tx scalability works : trans_start) (net: txq_trans_update() helper) Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Multi queue drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers (vxge & tehuti) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-08bnx2x: do not return negative number of received packagesStanislaw Gruszka1-1/+1
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-08bnx2x: free workqueue when driver fail to registerStanislaw Gruszka1-1/+8
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-27bnx2x: driver version 1.48.105-1Vladislav Zolotarov1-2/+2
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-27bnx2x: Separated FW from the source.Vladislav Zolotarov1-62/+281
>From now on FW will be downloaded from the binary file using request_firmware. There will be different files for every supported chip. Currently 57710 (e1) and 57711 (e1h). File names have the following format: bnx2x-<chip version>-<FW version>.fw. ihex versions of current FW files are submitted in the next patch. Each binary file has a header in the following format: struct bnx2x_fw_file_section { __be32 len; __be32 offset; } struct bnx2x_fw_file_hdr { struct bnx2x_fw_file_section init_ops; struct bnx2x_fw_file_section init_ops_offsets; struct bnx2x_fw_file_section init_data; struct bnx2x_fw_file_section tsem_int_table_data; struct bnx2x_fw_file_section tsem_pram_data; struct bnx2x_fw_file_section usem_int_table_data; struct bnx2x_fw_file_section usem_pram_data; struct bnx2x_fw_file_section csem_int_table_data; struct bnx2x_fw_file_section csem_pram_data; struct bnx2x_fw_file_section xsem_int_table_data; struct bnx2x_fw_file_section xsem_pram_data; struct bnx2x_fw_file_section fw_version; } Each bnx2x_fw_file_section contains the length and the offset of the appropriate section in the binary file. Values are stored in the big endian format. Data types of arrays: init_data __be32 init_ops_offsets __be16 XXsem_pram_data u8 XXsem_int_table_data u8 init_ops struct raw_op { u8 op; __be24 offset; __be32 data; } fw_version u8 >From now boundaries of a specific initialization stage are stored in init_ops_offsets array instead of being defined by separate macroes. The index in init_ops_offsets is calculated by BLOCK_OPS_IDX macro: #define BLOCK_OPS_IDX(block, stage, end) \ (2*(((block)*STAGE_IDX_MAX) + (stage)) + (end)) Security: In addition to sanity check of array boundaries bnx2x will check a FW version. Additional checks might be added in the future. Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-07dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)Yang Hongyang1-1/+1
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07dma-mapping: replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)Yang Hongyang1-2/+2
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-02bnx2x: Version updateEilon Greenstein1-2/+2
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Register dumpEilon Greenstein1-0/+81
Adding "ethtool -d" support. Due to the complexity of the FW and HW, there are a lot of different regions in the chip - to keep the code as clean as possible, the ranges were put in an H file. Some areas cannot be read if the driver is running - so by default, the driver will not access those areas - but any programmer facing a problem will be able to easily manipulate the driver to extract full dump. The full dump can also be used with kernel dump modules in case of kernel panic. Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Debug printsEilon Greenstein1-19/+19
Add the FP index to relevant debug prints and simply beautify some others Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: WhitespaceEilon Greenstein1-0/+1
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Calling tx disable unconditionallyEilon Greenstein1-4/+2
On unload, the FW assumes that no packets will be sent after the driver sends the FW stop command. To ensure that, the driver must always call netif_tx_disable Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Using DMA engineEilon Greenstein1-39/+12
Using DMA engine (DMAE) to initialize large consecutive memories in the chip Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Missing module parameter descriptionEilon Greenstein1-0/+1
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: napi_poll budget checkEilon Greenstein1-4/+18
Check the napi_poll budget only when updating it. Also add a comment to explain the rmb Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Unlimited Tx interrupt workEilon Greenstein1-7/+4
The Tx interrupt is very short and there is no need to limit it to a budget Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Add rmb to read status block indices on loadEilon Greenstein1-0/+4
Add rmb to read status block indices on load Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Reduce the likelihood of smb_mbEilon Greenstein1-7/+8
As the comment explains, this smb_mb is needed only if the queue is stopped (which is unlikely) so the barrier can be moved to that location Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02bnx2x: Remove redundant smb_mb on unloadEilon Greenstein1-2/+0
As noted by Ben Hutchings <bhutchings@solarflare.com>, these smb_mb are not needed Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: VersionEilon Greenstein1-2/+2
And updating the year Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Clean-upEilon Greenstein1-12/+23
Whitespaces, empty lines, 80 columns, indentations and removing redundant parenthesis Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Comments and printsEilon Greenstein1-21/+22
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Re-arrange module parametersEilon Greenstein1-7/+7
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Moving includesEilon Greenstein1-4/+1
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Driver dumpEilon Greenstein1-38/+59
Re-arrange the driver debug print to support the Tx multi-queue and add support for debug prints at the end of the ring (when start<end) Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Sparse endianity annotationEilon Greenstein1-31/+32
Resolving the majority of the issues, but there are still some left for future patches. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Removing redundant macrosEilon Greenstein1-26/+26
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Loopback in diag modeEilon Greenstein1-24/+33
When loading in diag mode, set the device to loopback instead of normal link and then changing it to loopback mode Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Using nvram default WoL configEilon Greenstein1-0/+6
The driver default WoL setting is set to the nvram default value Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: smp_mb and not just smp_rmbEilon Greenstein1-2/+2
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Increasing FW timeoutEilon Greenstein1-2/+6
When enabling many debug prints, it can take a while before processing an event. To ease the debug process, allow bigger timeout before giving up Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Returning EBUSY in debug mode as wellEilon Greenstein1-2/+1
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Manual setting for MRRSEilon Greenstein1-0/+6
Allows better debug capabilities if the user wants to force an MRRS value Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Pre emphasis configurationEilon Greenstein1-6/+25
Supporting non-default pre-emphasis settings for the internal and some external PHYs Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Supporting BCM8481 PHYEilon Greenstein1-0/+17
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: PHY lock listEilon Greenstein1-10/+10
Some dual port PHY require HW lock since they are used by both interfaces (different driver instances). Since this list is getting longer, update a parameter at load time instead of calculating it on runtime Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Supporting BCM8726 PHYEilon Greenstein1-15/+75
Also adding the ability to recognize the optic module and disable it if it is not authorized for safety reasons - since this feature might upset some users which are willing to take the risk, it is optional and can be disabled by setting an nvram bit (or a trivial driver patch to set this bit). This dual port PHY requires special handling if the ports are swapped. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: GPIO accessoriesEilon Greenstein1-2/+78
A GPIO is used with the 8726 PHY. Adding the GPIO related functions in this Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15bnx2x: Removing redundant device parametersEilon Greenstein1-10/+9
Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-19 11:29:03 +0000