summaryrefslogtreecommitdiff
path: root/arch/arm/mach-omap2/dpll44xx.c
AgeCommit message (Collapse)AuthorFilesLines
2014-01-17ARM: OMAP2+: clock: use driver API instead of direct memory read/writeTero Kristo1-6/+6
Clock nodes shall use the services provided by underlying drivers to access the hardware registers instead of direct memory read/write. Thus, change all the code to use the new omap2_clk_readl / omap2_clk_writel APIs for this. Signed-off-by: Tero Kristo <t-kristo@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-12-15ARM: OMAP4: Enhance support for DPLLs with 4X multiplierJon Hunter1-9/+55
On OMAP4 devices, the ABE DPLL has an internal 4X multiplier that can be enabled or disabled in addition to the standard configurable multiplier (M) for OMAP DPLLs. When configuring the ABE DPLL the 4X multiplier is accounted for by checking to see whether it is enabled or not. However, when calculating a new rate we only check to see if the rate can be achieved with the current setting for the 4X multiplier. Enhance the round_rate() function for such DPLLs to see if the rate can be achieved with the 4X multiplier if it cannot be achieved without the 4X multiplier. This change is necessary, because when using the 32kHz clock as the source clock for the ABE DPLL, the default DPLL frequency for the ABE DPLL cannot be achieved without enabling the 4X multiplier. When using the 32kHz clock as the source clock for the ABE DPLL and attempting to lock the DPLL to 98.304MHz (default frequency), it was found that the DPLL would fail to lock if the low-power mode for the DPLL was not enabled. From reviewing boot-loader settings that configure the ABE DPLL it was found that the low-power mode is enabled when using the 32kHz clock source, however, the documentation for OMAP does not state that this is a requirement. Therefore, introduce a new function for OMAP4 devices to see if low-power mode can be enabled when calculating a new rate to ensure the DPLL will lock. New variables for the last calculated 4X multiplier and low-power setting have been added to the dpll data structure as well as variables defining the bit mask for enabling these features via the DPLL's control_reg. It is possible that we could eliminate these bit masks from the dpll data structure as these bit masks are not unique to OMAP4, if it is preferred. The function omap3_noncore_program_dpll() has been updated to avoid passing the calculated values for the multiplier (M) and divider (N) as these are stored in the clk structure. Signed-off-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2012-11-12ARM: OMAP4: clock: Cleanup !CONFIG_COMMON_CLK partsRajendra Nayak1-33/+0
Clean all #ifdef's added to OMAP4 clock code to make it COMMON clk ready, now that CONFIG_COMMON_CLK is enabled. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: remove some ifdefs in mach-omap2/io.c] Signed-off-by: Paul Walmsley <paul@pwsan.com>
2012-11-12ARM: OMAP4: clock: Convert to common clkMike Turquette1-0/+38
Convert all OMAP4 specific platform files to use COMMON clk and keep all the changes under the CONFIG_COMMON_CLK macro check so it does not break any existing code. At a later point switch to COMMON clk and get rid of all old/legacy code. This converts all apis which will be called directly from COMMON clk to take a struct clk_hw parameter, and all the internal platform apis to take a struct clk_hw_omap parameter. Changes are based off the original patch from Mike Turquette. Signed-off-by: Rajendra Nayak <rnayak@ti.com> [paul@pwsan.com: created new omap2_clksel_find_parent_index() rather than modifying omap2_init_clksel_parent(); moved clkhwops_iclk_wait to clkt_iclk.c to fix OMAP4-only builds; added clk-provider.h include to clock.h to try to fix some 3430-builds] [mturquette@ti.com: squash patch for omap2_clkops_{en,dis}able_clkdm; omap2_dflt_clk_is_enabled should not enable clocks] Signed-off-by: Mike Turquette <mturquette@ti.com> [paul@pwsan.com: fix compiler warning; update to apply; added kerneldoc on non-trivial new functions; added the dpll3xxx clockdomain modifications] Signed-off-by: Paul Walmsley <paul@pwsan.com>
2012-10-18ARM: OMAP: remove plat/clock.hPaul Walmsley1-2/+0
Remove arch/arm/plat-omap/include/plat/clock.h by merging it into arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h. The goal here is to facilitate ARM single image kernels by removing includes via the "plat/" symlink. Signed-off-by: Paul Walmsley <paul@pwsan.com> [tony@atomide.com: fixed to remove duplicate clock.h includes] Signed-off-by: Tony Lindgren <tony@atomide.com>
2012-09-12ARM: OMAP: Split plat/hardware.h, use local soc.h for omap2+Tony Lindgren1-1/+1
As the plat and mach includes need to disappear for single zImage work, we need to remove plat/hardware.h. Do this by splitting plat/hardware.h into omap1 and omap2+ specific files. The old plat/hardware.h already has omap1 only defines, so it gets moved to mach/hardware.h for omap1. For omap2+, we use the local soc.h that for now just includes the related SoC headers to keep this patch more readable. Note that the local soc.h still includes plat/cpu.h that can be dealt with in later patches. Let's also include plat/serial.h from common.h for all the board-*.c files. This allows making the include files local later on without patching these files again. Note that only minimal changes are done in this patch for the drivers/watchdog/omap_wdt.c driver to keep things compiling. Further patches are needed to eventually remove cpu_is_omap usage in the drivers. Also only minimal changes are done to sound/soc/omap/* to remove the unneeded includes and to define OMAP44XX_MCPDM_L3_BASE locally so there's no need to include omap44xx.h. While at it, also sort some of the includes in the standard way. Cc: linux-watchdog@vger.kernel.org Cc: alsa-devel@alsa-project.org Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Jarkko Nikula <jarkko.nikula@bitmer.com> Cc: Liam Girdwood <lrg@ti.com> Acked-by: Wim Van Sebroeck <wim@iguana.be> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-10-07ARM: OMAP4: clock: round_rate and recalc functions for DPLL_ABEMike Turquette1-0/+69
OMAP4 DPLL_ABE can enable a 4X multipler on top of the normal MN multipler and divider. This is achieved by setting CM_CLKMODE_DPLL_ABE.DPLL_REGM4XEN bit in CKGEN module of CM1. From the OMAP4 TRM: Fdpll = Fref x 2 x (4 x M/(N+1)) in case REGM4XEN bit field is set (only applicable to DPLL_ABE). Add new round_rate() and recalc() functions for OMAP4, that check the setting of REGM4XEN bit and handle this appropriately. The new functions are a simple wrapper on top of the existing omap2_dpll_round_rate() and omap2_dpll_get_rate() functions to handle the REGM4XEN bit. The REGM4XEN bit is only implemented for the ABE DPLL on OMAP4 and so only dpll_abe_ck uses omap4_dpll_regm4xen_round_rate() and omap4_dpll_regm4xen_recalc() functions. Signed-off-by: Mike Turquette <mturquette@ti.com> Tested-by: Jon Hunter <jon-hunter@ti.com> Signed-off-by: Jon Hunter <jon-hunter@ti.com> [paul@pwsan.com: fixed attempt to return a negative from a fn returning unsigned; pass along errors from omap2_dpll_round_rate(); added documentation; added Jon's S-o-b] Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-02-25omap4: dpll: Enable auto gate control for all MX postdividersRajendra Nayak1-0/+6
Enable hardware gate control for all dpll MX and X2 postdividers. This requires the allow_idle/deny_idle functions to be populated for all clock nodes (mx/x2 post dividers) in clkops. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-02-25OMAP4: DPLL: Add dpll api to control GATE_CTRLRajendra Nayak1-0/+78
On OMAP4, the dpll post divider outputs (MX outputs) along with clockout_x2 output provide a way to allow/deny hardware level autogating. Allowing autoidle would mean that the hw would autogate this clock when there is no dependency for it. Denying idle would mean that this clock output will be forced to stay enabled. Add dpll api's to read/allow/deny idle control for these dpll mx postdividers. NOTE: The gatectrl bit set to 0 allows gatectrl, and the bit set to 1 denies gatectrl. Signed-off-by: Rajendra Nayak <rnayak@ti.com> [paul@pwsan.com: moved OMAP4-specific DPLL control code to mach-omap2/dpll44xx.c; added some documentation for CLOCK_CLKOUTX2] Signed-off-by: Paul Walmsley <paul@pwsan.com>