diff options
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_82599.c')
-rw-r--r-- | drivers/net/ixgbe/ixgbe_82599.c | 112 |
1 files changed, 76 insertions, 36 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c index 1f30e163bd9c..12fc0e7ba2ca 100644 --- a/drivers/net/ixgbe/ixgbe_82599.c +++ b/drivers/net/ixgbe/ixgbe_82599.c @@ -39,6 +39,9 @@ #define IXGBE_82599_MC_TBL_SIZE 128 #define IXGBE_82599_VFT_TBL_SIZE 128 +void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw); +void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw); +void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw); s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, ixgbe_link_speed speed, bool autoneg, @@ -68,7 +71,15 @@ static void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw) if (hw->phy.multispeed_fiber) { /* Set up dual speed SFP+ support */ mac->ops.setup_link = &ixgbe_setup_mac_link_multispeed_fiber; + mac->ops.disable_tx_laser = + &ixgbe_disable_tx_laser_multispeed_fiber; + mac->ops.enable_tx_laser = + &ixgbe_enable_tx_laser_multispeed_fiber; + mac->ops.flap_tx_laser = &ixgbe_flap_tx_laser_multispeed_fiber; } else { + mac->ops.disable_tx_laser = NULL; + mac->ops.enable_tx_laser = NULL; + mac->ops.flap_tx_laser = NULL; if ((mac->ops.get_media_type(hw) == ixgbe_media_type_backplane) && (hw->phy.smart_speed == ixgbe_smart_speed_auto || @@ -412,6 +423,67 @@ s32 ixgbe_start_mac_link_82599(struct ixgbe_hw *hw, return status; } + /** + * ixgbe_disable_tx_laser_multispeed_fiber - Disable Tx laser + * @hw: pointer to hardware structure + * + * The base drivers may require better control over SFP+ module + * PHY states. This includes selectively shutting down the Tx + * laser on the PHY, effectively halting physical link. + **/ +void ixgbe_disable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw) +{ + u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); + + /* Disable tx laser; allow 100us to go dark per spec */ + esdp_reg |= IXGBE_ESDP_SDP3; + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + IXGBE_WRITE_FLUSH(hw); + udelay(100); +} + +/** + * ixgbe_enable_tx_laser_multispeed_fiber - Enable Tx laser + * @hw: pointer to hardware structure + * + * The base drivers may require better control over SFP+ module + * PHY states. This includes selectively turning on the Tx + * laser on the PHY, effectively starting physical link. + **/ +void ixgbe_enable_tx_laser_multispeed_fiber(struct ixgbe_hw *hw) +{ + u32 esdp_reg = IXGBE_READ_REG(hw, IXGBE_ESDP); + + /* Enable tx laser; allow 100ms to light up */ + esdp_reg &= ~IXGBE_ESDP_SDP3; + IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + IXGBE_WRITE_FLUSH(hw); + msleep(100); +} + +/** + * ixgbe_flap_tx_laser_multispeed_fiber - Flap Tx laser + * @hw: pointer to hardware structure + * + * When the driver changes the link speeds that it can support, + * it sets autotry_restart to true to indicate that we need to + * initiate a new autotry session with the link partner. To do + * so, we set the speed then disable and re-enable the tx laser, to + * alert the link partner that it also needs to restart autotry on its + * end. This is consistent with true clause 37 autoneg, which also + * involves a loss of signal. + **/ +void ixgbe_flap_tx_laser_multispeed_fiber(struct ixgbe_hw *hw) +{ + hw_dbg(hw, "ixgbe_flap_tx_laser_multispeed_fiber\n"); + + if (hw->mac.autotry_restart) { + ixgbe_disable_tx_laser_multispeed_fiber(hw); + ixgbe_enable_tx_laser_multispeed_fiber(hw); + hw->mac.autotry_restart = false; + } +} + /** * ixgbe_setup_mac_link_multispeed_fiber - Set MAC link speed * @hw: pointer to hardware structure @@ -440,16 +512,6 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, speed &= phy_link_speed; /* - * When the driver changes the link speeds that it can support, - * it sets autotry_restart to true to indicate that we need to - * initiate a new autotry session with the link partner. To do - * so, we set the speed then disable and re-enable the tx laser, to - * alert the link partner that it also needs to restart autotry on its - * end. This is consistent with true clause 37 autoneg, which also - * involves a loss of signal. - */ - - /* * Try each speed one by one, highest priority first. We do this in * software because 10gb fiber doesn't support speed autonegotiation. */ @@ -466,6 +528,7 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, /* Set the module link speed */ esdp_reg |= (IXGBE_ESDP_SDP5_DIR | IXGBE_ESDP_SDP5); IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + IXGBE_WRITE_FLUSH(hw); /* Allow module to change analog characteristics (1G->10G) */ msleep(40); @@ -478,19 +541,7 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, return status; /* Flap the tx laser if it has not already been done */ - if (hw->mac.autotry_restart) { - /* Disable tx laser; allow 100us to go dark per spec */ - esdp_reg |= IXGBE_ESDP_SDP3; - IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - udelay(100); - - /* Enable tx laser; allow 2ms to light up per spec */ - esdp_reg &= ~IXGBE_ESDP_SDP3; - IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - msleep(2); - - hw->mac.autotry_restart = false; - } + hw->mac.ops.flap_tx_laser(hw); /* * Wait for the controller to acquire link. Per IEEE 802.3ap, @@ -525,6 +576,7 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, esdp_reg &= ~IXGBE_ESDP_SDP5; esdp_reg |= IXGBE_ESDP_SDP5_DIR; IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); + IXGBE_WRITE_FLUSH(hw); /* Allow module to change analog characteristics (10G->1G) */ msleep(40); @@ -537,19 +589,7 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, return status; /* Flap the tx laser if it has not already been done */ - if (hw->mac.autotry_restart) { - /* Disable tx laser; allow 100us to go dark per spec */ - esdp_reg |= IXGBE_ESDP_SDP3; - IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - udelay(100); - - /* Enable tx laser; allow 2ms to light up per spec */ - esdp_reg &= ~IXGBE_ESDP_SDP3; - IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp_reg); - msleep(2); - - hw->mac.autotry_restart = false; - } + hw->mac.ops.flap_tx_laser(hw); /* Wait for the link partner to also set speed */ msleep(100); |