diff options
Diffstat (limited to 'arch/avr32/boards')
-rw-r--r-- | arch/avr32/boards/atstk1000/Kconfig | 4 | ||||
-rw-r--r-- | arch/avr32/boards/atstk1000/Makefile | 1 | ||||
-rw-r--r-- | arch/avr32/boards/atstk1000/atstk1002.c | 97 | ||||
-rw-r--r-- | arch/avr32/boards/atstk1000/atstk1003.c | 2 | ||||
-rw-r--r-- | arch/avr32/boards/atstk1000/atstk1004.c | 2 |
5 files changed, 101 insertions, 5 deletions
diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig index af90b00100fd..8dc48214f0b7 100644 --- a/arch/avr32/boards/atstk1000/Kconfig +++ b/arch/avr32/boards/atstk1000/Kconfig @@ -18,6 +18,10 @@ config BOARD_ATSTK1004 bool "ATSTK1004" select CPU_AT32AP7002 +config BOARD_ATSTK1006 + bool "ATSTK1006" + select CPU_AT32AP7000 + endchoice diff --git a/arch/avr32/boards/atstk1000/Makefile b/arch/avr32/boards/atstk1000/Makefile index beead86462e8..edecee03742d 100644 --- a/arch/avr32/boards/atstk1000/Makefile +++ b/arch/avr32/boards/atstk1000/Makefile @@ -2,3 +2,4 @@ obj-y += setup.o flash.o obj-$(CONFIG_BOARD_ATSTK1002) += atstk1002.o obj-$(CONFIG_BOARD_ATSTK1003) += atstk1003.o obj-$(CONFIG_BOARD_ATSTK1004) += atstk1004.o +obj-$(CONFIG_BOARD_ATSTK1006) += atstk1002.o diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index e11659b732fa..8538ba75ef92 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -1,7 +1,7 @@ /* - * ATSTK1002 daughterboard-specific init code + * ATSTK1002/ATSTK1006 daughterboard-specific init code * - * Copyright (C) 2005-2006 Atmel Corporation + * Copyright (C) 2005-2007 Atmel Corporation * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -21,6 +21,8 @@ #include <asm/io.h> #include <asm/setup.h> +#include <asm/atmel-mci.h> + #include <asm/arch/at32ap700x.h> #include <asm/arch/board.h> #include <asm/arch/init.h> @@ -35,6 +37,74 @@ unsigned long at32_board_osc_rates[3] = { [2] = 12000000, /* 12 MHz on osc1 */ }; +/* + * The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both + * have the AT32AP7000 chip on board; the difference is that the + * STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on + * the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has + * none.) + * + * The RAM difference is handled by the boot loader, so the only + * difference we end up handling here is the NAND flash. + */ +#ifdef CONFIG_BOARD_ATSTK1006 +#include <linux/mtd/partitions.h> +#include <asm/arch/smc.h> + +static struct smc_timing nand_timing __initdata = { + .ncs_read_setup = 0, + .nrd_setup = 10, + .ncs_write_setup = 0, + .nwe_setup = 10, + + .ncs_read_pulse = 30, + .nrd_pulse = 15, + .ncs_write_pulse = 30, + .nwe_pulse = 15, + + .read_cycle = 30, + .write_cycle = 30, + + .ncs_read_recover = 0, + .nrd_recover = 15, + .ncs_write_recover = 0, + /* WE# high -> RE# low min 60 ns */ + .nwe_recover = 50, +}; + +static struct smc_config nand_config __initdata = { + .bus_width = 1, + .nrd_controlled = 1, + .nwe_controlled = 1, + .nwait_mode = 0, + .byte_write = 0, + .tdf_cycles = 2, + .tdf_mode = 0, +}; + +static struct mtd_partition nand_partitions[] = { + { + .name = "main", + .offset = 0x00000000, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct mtd_partition *nand_part_info(int size, int *num_partitions) +{ + *num_partitions = ARRAY_SIZE(nand_partitions); + return nand_partitions; +} + +struct atmel_nand_data atstk1006_nand_data __initdata = { + .cle = 21, + .ale = 22, + .rdy_pin = GPIO_PIN_PB(30), + .enable_pin = GPIO_PIN_PB(29), + .partition_info = nand_part_info, +}; +#endif + struct eth_addr { u8 addr[6]; }; @@ -192,6 +262,21 @@ void __init setup_board(void) at32_setup_serial_console(0); } +#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM + +/* MMC card detect requires MACB0 *NOT* be used */ +#ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM +static struct mci_platform_data __initdata mci0_data = { + .detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */ + .wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */ +}; +#define MCI_PDATA &mci0_data +#else +#define MCI_PDATA NULL +#endif /* SW6 for sd{cd,wp} routing */ + +#endif /* SW2 for MMC signal routing */ + static int __init atstk1002_init(void) { /* @@ -218,6 +303,12 @@ static int __init atstk1002_init(void) at32_add_system_devices(); +#ifdef CONFIG_BOARD_ATSTK1006 + smc_set_timing(&nand_config, &nand_timing); + smc_set_configuration(3, &nand_config); + at32_add_device_nand(0, &atstk1006_nand_data); +#endif + #ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM at32_add_device_usart(1); #else @@ -235,7 +326,7 @@ static int __init atstk1002_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK1002_SW2_CUSTOM - at32_add_device_mci(0, NULL); + at32_add_device_mci(0, MCI_PDATA); #endif #ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM set_hw_addr(at32_add_device_eth(1, ð_data[1])); diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c index ea109f435a83..591fc73b554a 100644 --- a/arch/avr32/boards/atstk1000/atstk1003.c +++ b/arch/avr32/boards/atstk1000/atstk1003.c @@ -154,7 +154,7 @@ static int __init atstk1003_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_add_device_mci(0); + at32_add_device_mci(0, NULL); #endif at32_add_device_usba(0, NULL); #ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c index c7236df74d74..d9c5e0a21256 100644 --- a/arch/avr32/boards/atstk1000/atstk1004.c +++ b/arch/avr32/boards/atstk1000/atstk1004.c @@ -137,7 +137,7 @@ static int __init atstk1004_init(void) at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info)); #endif #ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM - at32_add_device_mci(0); + at32_add_device_mci(0, NULL); #endif at32_add_device_lcdc(0, &atstk1000_lcdc_data, fbmem_start, fbmem_size, 0); |