diff options
356 files changed, 6866 insertions, 9735 deletions
diff --git a/Documentation/networking/bonding.txt b/Documentation/networking/bonding.txt index 11340625e363..6cc30e0d5795 100644 --- a/Documentation/networking/bonding.txt +++ b/Documentation/networking/bonding.txt @@ -554,6 +554,30 @@ xmit_hash_policy This algorithm is 802.3ad compliant. + layer2+3 + + This policy uses a combination of layer2 and layer3 + protocol information to generate the hash. + + Uses XOR of hardware MAC addresses and IP addresses to + generate the hash. The formula is + + (((source IP XOR dest IP) AND 0xffff) XOR + ( source MAC XOR destination MAC )) + modulo slave count + + This algorithm will place all traffic to a particular + network peer on the same slave. For non-IP traffic, + the formula is the same as for the layer2 transmit + hash policy. + + This policy is intended to provide a more balanced + distribution of traffic than layer2 alone, especially + in environments where a layer3 gateway device is + required to reach most destinations. + + This algorithm is 802.3ad complient. + layer3+4 This policy uses upper layer protocol information, @@ -589,8 +613,9 @@ xmit_hash_policy or may not tolerate this noncompliance. The default value is layer2. This option was added in bonding -version 2.6.3. In earlier versions of bonding, this parameter does -not exist, and the layer2 policy is the only policy. + version 2.6.3. In earlier versions of bonding, this parameter + does not exist, and the layer2 policy is the only policy. The + layer2+3 value was added for bonding version 3.2.2. 3. Configuring Bonding Devices diff --git a/MAINTAINERS b/MAINTAINERS index 7c8392e1797d..f3d7256bc74e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1681,8 +1681,7 @@ S: Maintained HARMONY SOUND DRIVER P: Kyle McMartin M: kyle@parisc-linux.org -W: http://www.parisc-linux.org/~kyle/harmony/ -L: parisc-linux@lists.parisc-linux.org +L: linux-parisc@vger.kernel.org S: Maintained HAYES ESP SERIAL DRIVER @@ -2173,7 +2172,7 @@ S: Maintained KDUMP P: Vivek Goyal -M: vgoyal@in.ibm.com +M: vgoyal@redhat.com P: Haren Myneni M: hbabu@us.ibm.com L: kexec@lists.infradead.org @@ -2598,13 +2597,6 @@ L: https://tango.0pointer.de/mailman/listinfo/s270-linux W: http://0pointer.de/lennart/tchibo.html S: Maintained -MTRR AND SIMILAR SUPPORT [i386] -P: Richard Gooch -M: rgooch@atnf.csiro.au -L: linux-kernel@vger.kernel.org -W: http://www.atnf.csiro.au/~rgooch/linux/kernel-patches.html -S: Maintained - MULTIMEDIA CARD (MMC), SECURE DIGITAL (SD) AND SDIO SUBSYSTEM P: Pierre Ossman M: drzeus-mmc@drzeus.cx @@ -2897,16 +2889,15 @@ W: http://www.torque.net/linux-pp.html S: Maintained PARISC ARCHITECTURE +P: Kyle McMartin +M: kyle@parisc-linux.org P: Matthew Wilcox M: matthew@wil.cx P: Grant Grundler M: grundler@parisc-linux.org -P: Kyle McMartin -M: kyle@parisc-linux.org -L: parisc-linux@parisc-linux.org +L: linux-parisc@vger.kernel.org W: http://www.parisc-linux.org/ T: git kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6.git -T: cvs cvs.parisc-linux.org:/var/cvs/linux-2.6 S: Maintained PARAVIRT_OPS INTERFACE @@ -1,7 +1,7 @@ VERSION = 2 PATCHLEVEL = 6 SUBLEVEL = 24 -EXTRAVERSION = -rc3 +EXTRAVERSION = -rc4 NAME = Arr Matey! A Hairy Bilge Rat! # *DOCUMENTATION* diff --git a/arch/avr32/Kconfig b/arch/avr32/Kconfig index 4f402c924504..b77abce10c7a 100644 --- a/arch/avr32/Kconfig +++ b/arch/avr32/Kconfig @@ -6,8 +6,7 @@ mainmenu "Linux Kernel Configuration" config AVR32 - bool - default y + def_bool y # With EMBEDDED=n, we get lots of stuff automatically selected # that we usually don't need on AVR32. select EMBEDDED @@ -20,51 +19,49 @@ config AVR32 http://avr32linux.org/. config GENERIC_GPIO - bool - default y + def_bool y config GENERIC_HARDIRQS - bool - default y + def_bool y + +config STACKTRACE_SUPPORT + def_bool y + +config LOCKDEP_SUPPORT + def_bool y + +config TRACE_IRQFLAGS_SUPPORT + def_bool y config HARDIRQS_SW_RESEND - bool - default y + def_bool y config GENERIC_IRQ_PROBE - bool - default y + def_bool y config RWSEM_GENERIC_SPINLOCK - bool - default y + def_bool y config GENERIC_TIME - bool - default y + def_bool y config RWSEM_XCHGADD_ALGORITHM - bool + def_bool n config ARCH_HAS_ILOG2_U32 - bool - default n + def_bool n config ARCH_HAS_ILOG2_U64 - bool - default n + def_bool n config GENERIC_HWEIGHT - bool - default y + def_bool y config GENERIC_CALIBRATE_DELAY - bool - default y + def_bool y config GENERIC_BUG - bool - default y + def_bool y depends on BUG source "init/Kconfig" @@ -139,28 +136,22 @@ config PHYS_OFFSET source "kernel/Kconfig.preempt" config HAVE_ARCH_BOOTMEM_NODE - bool - default n + def_bool n config ARCH_HAVE_MEMORY_PRESENT - bool - default n + def_bool n config NEED_NODE_MEMMAP_SIZE - bool - default n + def_bool n config ARCH_FLATMEM_ENABLE - bool - default y + def_bool y config ARCH_DISCONTIGMEM_ENABLE - bool - default n + def_bool n config ARCH_SPARSEMEM_ENABLE - bool - default n + def_bool n source "mm/Kconfig" diff --git a/arch/avr32/kernel/Makefile b/arch/avr32/kernel/Makefile index 989fcd1fef7e..2d6d48f35f69 100644 --- a/arch/avr32/kernel/Makefile +++ b/arch/avr32/kernel/Makefile @@ -11,3 +11,4 @@ obj-y += signal.o sys_avr32.o process.o time.o obj-y += init_task.o switch_to.o cpu.o obj-$(CONFIG_MODULES) += module.o avr32_ksyms.o obj-$(CONFIG_KPROBES) += kprobes.o +obj-$(CONFIG_STACKTRACE) += stacktrace.o diff --git a/arch/avr32/kernel/asm-offsets.c b/arch/avr32/kernel/asm-offsets.c index 97d865865667..078cd33f467b 100644 --- a/arch/avr32/kernel/asm-offsets.c +++ b/arch/avr32/kernel/asm-offsets.c @@ -21,5 +21,7 @@ void foo(void) OFFSET(TI_flags, thread_info, flags); OFFSET(TI_cpu, thread_info, cpu); OFFSET(TI_preempt_count, thread_info, preempt_count); + OFFSET(TI_rar_saved, thread_info, rar_saved); + OFFSET(TI_rsr_saved, thread_info, rsr_saved); OFFSET(TI_restart_block, thread_info, restart_block); } diff --git a/arch/avr32/kernel/entry-avr32b.S b/arch/avr32/kernel/entry-avr32b.S index ccadfd9b438d..8cf16d7a7040 100644 --- a/arch/avr32/kernel/entry-avr32b.S +++ b/arch/avr32/kernel/entry-avr32b.S @@ -264,16 +264,7 @@ syscall_exit_work: 3: bld r1, TIF_BREAKPOINT brcc syscall_exit_cont - mfsr r3, SYSREG_TLBEHI - lddsp r2, sp[REG_PC] - andl r3, 0xff, COH - lsl r3, 1 - sbr r3, 30 - sbr r3, 0 - mtdr DBGREG_BWA2A, r2 - mtdr DBGREG_BWC2A, r3 - rjmp syscall_exit_cont - + rjmp enter_monitor_mode /* The slow path of the TLB miss handler */ page_table_not_present: @@ -288,11 +279,16 @@ page_not_present: rjmp ret_from_exception /* This function expects to find offending PC in SYSREG_RAR_EX */ + .type save_full_context_ex, @function + .align 2 save_full_context_ex: + mfsr r11, SYSREG_RAR_EX + sub r9, pc, . - debug_trampoline mfsr r8, SYSREG_RSR_EX + cp.w r9, r11 + breq 3f mov r12, r8 andh r8, (MODE_MASK >> 16), COH - mfsr r11, SYSREG_RAR_EX brne 2f 1: pushm r11, r12 /* PC and SR */ @@ -303,10 +299,25 @@ save_full_context_ex: stdsp sp[4], r10 /* replace saved SP */ rjmp 1b + /* + * The debug handler set up a trampoline to make us + * automatically enter monitor mode upon return, but since + * we're saving the full context, we must assume that the + * exception handler might want to alter the return address + * and/or status register. So we need to restore the original + * context and enter monitor mode manually after the exception + * has been handled. + */ +3: get_thread_info r8 + ld.w r11, r8[TI_rar_saved] + ld.w r12, r8[TI_rsr_saved] + rjmp 1b + .size save_full_context_ex, . - save_full_context_ex + /* Low-level exception handlers */ handle_critical: - pushm r12 - pushm r0-r12 + sub sp, 4 + stmts --sp, r0-lr rcall save_full_context_ex mfsr r12, SYSREG_ECR mov r11, sp @@ -439,6 +450,7 @@ do_fpe_ll: ret_from_exception: mask_interrupts lddsp r4, sp[REG_SR] + andh r4, (MODE_MASK >> 16), COH brne fault_resume_kernel @@ -515,119 +527,124 @@ fault_exit_work: 2: bld r1, TIF_BREAKPOINT brcc fault_resume_user - mfsr r3, SYSREG_TLBEHI - lddsp r2, sp[REG_PC] - andl r3, 0xff, COH - lsl r3, 1 - sbr r3, 30 - sbr r3, 0 - mtdr DBGREG_BWA2A, r2 - mtdr DBGREG_BWC2A, r3 - rjmp fault_resume_user - - /* If we get a debug trap from privileged context we end up here */ -handle_debug_priv: - /* Fix up LR and SP in regs. r11 contains the mode we came from */ + rjmp enter_monitor_mode + + .section .kprobes.text, "ax", @progbits + .type handle_debug, @function +handle_debug: + sub sp, 4 /* r12_orig */ + stmts --sp, r0-lr + mfsr r8, SYSREG_RAR_DBG + mfsr r9, SYSREG_RSR_DBG + unmask_exceptions + pushm r8-r9 + bfextu r9, r9, SYSREG_MODE_OFFSET, SYSREG_MODE_SIZE + brne debug_fixup_regs + +.Ldebug_fixup_cont: +#ifdef CONFIG_TRACE_IRQFLAGS + rcall trace_hardirqs_off +#endif + mov r12, sp + rcall do_debug + mov sp, r12 + + lddsp r2, sp[REG_SR] + bfextu r3, r2, SYSREG_MODE_OFFSET, SYSREG_MODE_SIZE + brne debug_resume_kernel + + get_thread_info r0 + ld.w r1, r0[TI_flags] + mov r2, _TIF_DBGWORK_MASK + tst r1, r2 + brne debug_exit_work + + bld r1, TIF_SINGLE_STEP + brcc 1f + mfdr r4, OCD_DC + sbr r4, OCD_DC_SS_BIT + mtdr OCD_DC, r4 + +1: popm r10,r11 + mask_exceptions + mtsr SYSREG_RSR_DBG, r11 + mtsr SYSREG_RAR_DBG, r10 +#ifdef CONFIG_TRACE_IRQFLAGS + rcall trace_hardirqs_on +1: +#endif + ldmts sp++, r0-lr + sub sp, -4 + retd + .size handle_debug, . - handle_debug + + /* Mode of the trapped context is in r9 */ + .type debug_fixup_regs, @function +debug_fixup_regs: mfsr r8, SYSREG_SR - mov r9, r8 - andh r8, hi(~MODE_MASK) - or r8, r11 + mov r10, r8 + bfins r8, r9, SYSREG_MODE_OFFSET, SYSREG_MODE_SIZE mtsr SYSREG_SR, r8 sub pc, -2 stdsp sp[REG_LR], lr - mtsr SYSREG_SR, r9 + mtsr SYSREG_SR, r10 sub pc, -2 - sub r10, sp, -FRAME_SIZE_FULL - stdsp sp[REG_SP], r10 - mov r12, sp - rcall do_debug_priv + sub r8, sp, -FRAME_SIZE_FULL + stdsp sp[REG_SP], r8 + rjmp .Ldebug_fixup_cont + .size debug_fixup_regs, . - debug_fixup_regs - /* Now, put everything back */ - ssrf SR_EM_BIT + .type debug_resume_kernel, @function +debug_resume_kernel: + mask_exceptions popm r10, r11 mtsr SYSREG_RAR_DBG, r10 mtsr SYSREG_RSR_DBG, r11 - mfsr r8, SYSREG_SR - mov r9, r8 - andh r8, hi(~MODE_MASK) - andh r11, hi(MODE_MASK) - or r8, r11 - mtsr SYSREG_SR, r8 +#ifdef CONFIG_TRACE_IRQFLAGS + bld r11, SYSREG_GM_OFFSET + brcc 1f + rcall trace_hardirqs_on +1: +#endif + mfsr r2, SYSREG_SR + mov r1, r2 + bfins r2, r3, SYSREG_MODE_OFFSET, SYSREG_MODE_SIZE + mtsr SYSREG_SR, r2 sub pc, -2 popm lr - mtsr SYSREG_SR, r9 + mtsr SYSREG_SR, r1 sub pc, -2 sub sp, -4 /* skip SP */ popm r0-r12 sub sp, -4 retd + .size debug_resume_kernel, . - debug_resume_kernel + .type debug_exit_work, @function +debug_exit_work: /* - * At this point, everything is masked, that is, interrupts, - * exceptions and debugging traps. We might get called from - * interrupt or exception context in some rare cases, but this - * will be taken care of by do_debug(), so we're not going to - * do a 100% correct context save here. + * We must return from Monitor Mode using a retd, and we must + * not schedule since that involves the D bit in SR getting + * cleared by something other than the debug hardware. This + * may cause undefined behaviour according to the Architecture + * manual. + * + * So we fix up the return address and status and return to a + * stub below in Exception mode. From there, we can follow the + * normal exception return path. + * + * The real return address and status registers are stored on + * the stack in the way the exception return path understands, + * so no need to fix anything up there. */ -handle_debug: - sub sp, 4 /* r12_orig */ - stmts --sp, r0-lr - mfsr r10, SYSREG_RAR_DBG - mfsr r11, SYSREG_RSR_DBG - unmask_exceptions - pushm r10,r11 - andh r11, (MODE_MASK >> 16), COH - brne handle_debug_priv - - mov r12, sp - rcall do_debug - - lddsp r10, sp[REG_SR] - andh r10, (MODE_MASK >> 16), COH - breq debug_resume_user - -debug_restore_all: - popm r10,r11 - mask_exceptions - mtsr SYSREG_RSR_DBG, r11 - mtsr SYSREG_RAR_DBG, r10 - ldmts sp++, r0-lr - sub sp, -4 + sub r8, pc, . - fault_exit_work + mtsr SYSREG_RAR_DBG, r8 + mov r9, 0 + orh r9, hi(SR_EM | SR_GM | MODE_EXCEPTION) + mtsr SYSREG_RSR_DBG, r9 + sub pc, -2 retd - -debug_resume_user: - get_thread_info r0 - mask_interrupts - - ld.w r1, r0[TI_flags] - andl r1, _TIF_DBGWORK_MASK, COH - breq debug_restore_all - -1: bld r1, TIF_NEED_RESCHED - brcc 2f - unmask_interrupts - rcall schedule - mask_interrupts - ld.w r1, r0[TI_flags] - rjmp 1b - -2: mov r2, _TIF_SIGPENDING | _TIF_RESTORE_SIGMASK - tst r1, r2 - breq 3f - unmask_interrupts - mov r12, sp - mov r11, r0 - rcall do_notify_resume - mask_interrupts - ld.w r1, r0[TI_flags] - rjmp 1b - -3: bld r1, TIF_SINGLE_STEP - brcc debug_restore_all - mfdr r2, DBGREG_DC - sbr r2, DC_SS_BIT - mtdr DBGREG_DC, r2 - rjmp debug_restore_all + .size debug_exit_work, . - debug_exit_work .set rsr_int0, SYSREG_RSR_INT0 .set rsr_int1, SYSREG_RSR_INT1 @@ -675,7 +692,11 @@ irq_level\level: andl r1, _TIF_WORK_MASK, COH brne irq_exit_work -1: popm r8-r9 +1: +#ifdef CONFIG_TRACE_IRQFLAGS + rcall trace_hardirqs_on +#endif + popm r8-r9 mtsr rar_int\level, r8 mtsr rsr_int\level, r9 ldmts sp++,r0-lr @@ -748,3 +769,53 @@ cpu_idle_enable_int_and_exit: IRQ_LEVEL 1 IRQ_LEVEL 2 IRQ_LEVEL 3 + + .section .kprobes.text, "ax", @progbits + .type enter_monitor_mode, @function +enter_monitor_mode: + /* + * We need to enter monitor mode to do a single step. The + * monitor code will alter the return address so that we + * return directly to the user instead of returning here. + */ + breakpoint + rjmp breakpoint_failed + + .size enter_monitor_mode, . - enter_monitor_mode + + .type debug_trampoline, @function + .global debug_trampoline +debug_trampoline: + /* + * Save the registers on the stack so that the monitor code + * can find them easily. + */ + sub sp, 4 /* r12_orig */ + stmts --sp, r0-lr + get_thread_info r0 + ld.w r8, r0[TI_rar_saved] + ld.w r9, r0[TI_rsr_saved] + pushm r8-r9 + + /* + * The monitor code will alter the return address so we don't + * return here. + */ + breakpoint + rjmp breakpoint_failed + .size debug_trampoline, . - debug_trampoline + + .type breakpoint_failed, @function +breakpoint_failed: + /* + * Something went wrong. Perhaps the debug hardware isn't + * enabled? + */ + lda.w r12, msg_breakpoint_failed + mov r11, sp + mov r10, 9 /* SIGKILL */ + call die +1: rjmp 1b + +msg_breakpoint_failed: + .asciz "Failed to enter Debug Mode" diff --git a/arch/avr32/kernel/kprobes.c b/arch/avr32/kernel/kprobes.c index 20b1c9d8f945..799ba89b07a8 100644 --- a/arch/avr32/kernel/kprobes.c +++ b/arch/avr32/kernel/kprobes.c @@ -70,9 +70,9 @@ static void __kprobes prepare_singlestep(struct kprobe *p, struct pt_regs *regs) BUG_ON(!(sysreg_read(SR) & SYSREG_BIT(SR_D))); - dc = __mfdr(DBGREG_DC); - dc |= DC_SS; - __mtdr(DBGREG_DC, dc); + dc = ocd_read(DC); + dc |= 1 << OCD_DC_SS_BIT; + ocd_write(DC, dc); /* * We must run the instruction from its original location @@ -91,9 +91,9 @@ static void __kprobes resume_execution(struct kprobe *p, struct pt_regs *regs) pr_debug("resuming execution at PC=%08lx\n", regs->pc); - dc = __mfdr(DBGREG_DC); - dc &= ~DC_SS; - __mtdr(DBGREG_DC, dc); + dc = ocd_read(DC); + dc &= ~(1 << OCD_DC_SS_BIT); + ocd_write(DC, dc); *p->addr = BREAKPOINT_INSTRUCTION; flush_icache_range((unsigned long)p->addr, @@ -261,7 +261,7 @@ int __kprobes longjmp_break_handler(struct kprobe *p, struct pt_regs *regs) int __init arch_init_kprobes(void) { printk("KPROBES: Enabling monitor mode (MM|DBE)...\n"); - __mtdr(DBGREG_DC, DC_MM | DC_DBE); + ocd_write(DC, (1 << OCD_DC_MM_BIT) | (1 << OCD_DC_DBE_BIT)); /* TODO: Register kretprobe trampoline */ return 0; diff --git a/arch/avr32/kernel/process.c b/arch/avr32/kernel/process.c index 13f988402613..9d6dac8af7a2 100644 --- a/arch/avr32/kernel/process.c +++ b/arch/avr32/kernel/process.c @@ -55,8 +55,8 @@ void machine_power_off(void) void machine_restart(char *cmd) { - __mtdr(DBGREG_DC, DC_DBE); - __mtdr(DBGREG_DC, DC_RES); + ocd_write(DC, (1 << OCD_DC_DBE_BIT)); + ocd_write(DC, (1 << OCD_DC_RES_BIT)); while (1) ; } @@ -287,10 +287,11 @@ void show_regs_log_lvl(struct pt_regs *regs, const char *log_lvl) regs->sr & SR_N ? 'N' : 'n', regs->sr & SR_Z ? 'Z' : 'z', regs->sr & SR_C ? 'C' : 'c'); - printk("%sMode bits: %c%c%c%c%c%c%c%c%c\n", log_lvl, + printk("%sMode bits: %c%c%c%c%c%c%c%c%c%c\n", log_lvl, regs->sr & SR_H ? 'H' : 'h', - regs->sr & SR_R ? 'R' : 'r', regs->sr & SR_J ? 'J' : 'j', + regs->sr & SR_DM ? 'M' : 'm', + regs->sr & SR_D ? 'D' : 'd', regs->sr & SR_EM ? 'E' : 'e', regs->sr & SR_I3M ? '3' : '.', regs->sr & SR_I2M ? '2' : '.', diff --git a/arch/avr32/kernel/ptrace.c b/arch/avr32/kernel/ptrace.c index 9e16b8a447f2..002369e44093 100644 --- a/arch/avr32/kernel/ptrace.c +++ b/arch/avr32/kernel/ptrace.c @@ -30,20 +30,22 @@ static struct pt_regs *get_user_regs(struct task_struct *tsk) static void ptrace_single_step(struct task_struct *tsk) { - pr_debug("ptrace_single_step: pid=%u, SR=0x%08lx\n", - tsk->pid, tsk->thread.cpu_context.sr); - if (!(tsk->thread.cpu_context.sr & SR_D)) { - /* - * Set a breakpoint at the current pc to force the - * process into debug mode. The syscall/exception - * exit code will set a breakpoint at the return - * address when this flag is set. - */ - pr_debug("ptrace_single_step: Setting TIF_BREAKPOINT\n"); - set_tsk_thread_flag(tsk, TIF_BREAKPOINT); - } + pr_debug("ptrace_single_step: pid=%u, PC=0x%08lx, SR=0x%08lx\n", + tsk->pid, task_pt_regs(tsk)->pc, task_pt_regs(tsk)->sr); - /* The monitor code will do the actual step for us */ + /* + * We can't schedule in Debug mode, so when TIF_BREAKPOINT is + * set, the system call or exception handler will do a + * breakpoint to enter monitor mode before returning to + * userspace. + * + * The monitor code will then notice that TIF_SINGLE_STEP is + * set and return to userspace with single stepping enabled. + * The CPU will then enter monitor mode again after exactly + * one instruction has been executed, and the monitor code + * will then send a SIGTRAP to the process. + */ + set_tsk_thread_flag(tsk, TIF_BREAKPOINT); set_tsk_thread_flag(tsk, TIF_SINGLE_STEP); } @@ -55,23 +57,7 @@ static void ptrace_single_step(struct task_struct *tsk) void ptrace_disable(struct task_struct *child) { clear_tsk_thread_flag(child, TIF_SINGLE_STEP); -} - -/* - * Handle hitting a breakpoint - */ -static void ptrace_break(struct task_struct *tsk, struct pt_regs *regs) -{ - siginfo_t info; - - info.si_signo = SIGTRAP; - info.si_errno = 0; - info.si_code = TRAP_BRKPT; - info.si_addr = (void __user *)instruction_pointer(regs); - - pr_debug("ptrace_break: Sending SIGTRAP to PID %u (pc = 0x%p)\n", - tsk->pid, info.si_addr); - force_sig_info(SIGTRAP, &info, tsk); + clear_tsk_thread_flag(child, TIF_BREAKPOINT); } /* @@ -84,9 +70,6 @@ static int ptrace_read_user(struct task_struct *tsk, unsigned long offset, unsigned long *regs; unsigned long value; - pr_debug("ptrace_read_user(%p, %#lx, %p)\n", - tsk, offset, data); - if (offset & 3 || offset >= sizeof(struct user)) { printk("ptrace_read_user: invalid offset 0x%08lx\n", offset); return -EIO; @@ -98,6 +81,9 @@ static int ptrace_read_user(struct task_struct *tsk, unsigned long offset, if (offset < sizeof(struct pt_regs)) value = regs[offset / sizeof(regs[0])]; + pr_debug("ptrace_read_user(%s[%u], %#lx, %p) -> %#lx\n", + tsk->comm, tsk->pid, offset, data, value); + return put_user(value, data); } @@ -111,8 +97,11 @@ static int ptrace_write_user(struct task_struct *tsk, unsigned long offset, { unsigned long *regs; + pr_debug("ptrace_write_user(%s[%u], %#lx, %#lx)\n", + tsk->comm, tsk->pid, offset, value); + if (offset & 3 || offset >= sizeof(struct user)) { - printk("ptrace_write_user: invalid offset 0x%08lx\n", offset); + pr_debug(" invalid offset 0x%08lx\n", offset); return -EIO; } @@ -155,11 +144,9 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data) { int ret; - pr_debug("arch_ptrace(%ld, %d, %#lx, %#lx)\n", - request, child->pid, addr, data); - pr_debug("ptrace: Enabling monitor mode...\n"); - __mtdr(DBGREG_DC, __mfdr(DBGREG_DC) | DC_MM | DC_DBE); + ocd_write(DC, ocd_read(DC) | (1 << OCD_DC_MM_BIT) + | (1 << OCD_DC_DBE_BIT)); switch (request) { /* Read the word at location addr in the child process */ @@ -240,19 +227,16 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data) break; } - pr_debug("sys_ptrace returning %d (DC = 0x%08lx)\n", ret, __mfdr(DBGREG_DC)); return ret; } asmlinkage void syscall_trace(void) { - pr_debug("syscall_trace called\n"); if (!test_thread_flag(TIF_SYSCALL_TRACE)) return; if (!(current->ptrace & PT_PTRACED)) return; - pr_debug("syscall_trace: notifying parent\n"); /* The 0x80 provides a way for the tracing parent to * distinguish between a syscall stop and SIGTRAP delivery */ ptrace_notify(SIGTRAP | ((current->ptrace & PT_TRACESYSGOOD) @@ -271,86 +255,143 @@ asmlinkage void syscall_trace(void) } } -asmlinkage void do_debug_priv(struct pt_regs *regs) -{ - unsigned long dc, ds; - unsigned long die_val; - - ds = __mfdr(DBGREG_DS); - - pr_debug("do_debug_priv: pc = %08lx, ds = %08lx\n", regs->pc, ds); - - if (ds & DS_SSS) - die_val = DIE_SSTEP; - else - die_val = DIE_BREAKPOINT; - - if (notify_die(die_val, "ptrace", regs, 0, 0, SIGTRAP) == NOTIFY_STOP) - return; - - if (likely(ds & DS_SSS)) { - extern void itlb_miss(void); - extern void tlb_miss_common(void); - struct thread_info *ti; - - dc = __mfdr(DBGREG_DC); - dc &= ~DC_SS; - __mtdr(DBGREG_DC, dc); - - ti = current_thread_info(); - set_ti_thread_flag(ti, TIF_BREAKPOINT); - - /* The TLB miss handlers don't check thread flags */ - if ((regs->pc >= (unsigned long)&itlb_miss) - && (regs->pc <= (unsigned long)&tlb_miss_common)) { - __mtdr(DBGREG_BWA2A, sysreg_read(RAR_EX)); - __mtdr(DBGREG_BWC2A, 0x40000001 | (get_asid() << 1)); - } - - /* - * If we're running in supervisor mode, the breakpoint - * will take us where we want directly, no need to - * single step. - */ - if ((regs->sr & MODE_MASK) != MODE_SUPERVISOR) - set_ti_thread_flag(ti, TIF_SINGLE_STEP); - } else { - panic("Unable to handle debug trap at pc = %08lx\n", - regs->pc); - } -} - /* - * Handle breakpoints, single steps and other debuggy things. To keep - * things simple initially, we run with interrupts and exceptions - * disabled all the time. + * debug_trampoline() is an assembly stub which will store all user + * registers on the stack and execute a breakpoint instruction. + * + * If we single-step into an exception handler which runs with + * interrupts disabled the whole time so it doesn't have to check for + * pending work, its return address will be modified so that it ends + * up returning to debug_trampoline. + * + * If the exception handler decides to store the user context and + * enable interrupts after all, it will restore the original return + * address and status register value. Before it returns, it will + * notice that TIF_BREAKPOINT is set and execute a breakpoint + * instruction. */ -asmlinkage void do_debug(struct pt_regs *regs) -{ - unsigned long dc, ds; +extern void debug_trampoline(void); - ds = __mfdr(DBGREG_DS); - pr_debug("do_debug: pc = %08lx, ds = %08lx\n", regs->pc, ds); +asmlinkage struct pt_regs *do_debug(struct pt_regs *regs) +{ + struct thread_info *ti; + unsigned long trampoline_addr; + u32 status; + u32 ctrl; + int code; + + status = ocd_read(DS); + ti = current_thread_info(); + code = TRAP_BRKPT; + + pr_debug("do_debug: status=0x%08x PC=0x%08lx SR=0x%08lx tif=0x%08lx\n", + status, regs->pc, regs->sr, ti->flags); + + if (!user_mode(regs)) { + unsigned long die_val = DIE_BREAKPOINT; + + if (status & (1 << OCD_DS_SSS_BIT)) + die_val = DIE_SSTEP; + + if (notify_die(die_val, "ptrace", regs, 0, 0, SIGTRAP) + == NOTIFY_STOP) + return regs; + + if ((status & (1 << OCD_DS_SWB_BIT)) + && test_and_clear_ti_thread_flag( + ti, TIF_BREAKPOINT)) { + /* + * Explicit breakpoint from trampoline or + * exception/syscall/interrupt handler. + * + * The real saved regs are on the stack right + * after the ones we saved on entry. + */ + regs++; + pr_debug(" -> TIF_BREAKPOINT done, adjusted regs:" + "PC=0x%08lx SR=0x%08lx\n", + regs->pc, regs->sr); + BUG_ON(!user_mode(regs)); + + if (test_thread_flag(TIF_SINGLE_STEP)) { + pr_debug("Going to do single step...\n"); + return regs; + } + + /* + * No TIF_SINGLE_STEP means we're done + * stepping over a syscall. Do the trap now. + */ + code = TRAP_TRACE; + } else if ((status & (1 << OCD_DS_SSS_BIT)) + && test_ti_thread_flag(ti, TIF_SINGLE_STEP)) { + + pr_debug("Stepped into something, " + "setting TIF_BREAKPOINT...\n"); + set_ti_thread_flag(ti, TIF_BREAKPOINT); + + /* + * We stepped into an exception, interrupt or + * syscall handler. Some exception handlers + * don't check for pending work, so we need to + * set up a trampoline just in case. + * + * The exception entry code will undo the + * trampoline stuff if it does a full context + * save (which also means that it'll check for + * pending work later.) + */ + if ((regs->sr & MODE_MASK) == MODE_EXCEPTION) { + trampoline_addr + = (unsigned long)&debug_trampoline; + + pr_debug("Setting up trampoline...\n"); + ti->rar_saved = sysreg_read(RAR_EX); + ti->rsr_saved = sysreg_read(RSR_EX); + sysreg_write(RAR_EX, trampoline_addr); + sysreg_write(RSR_EX, (MODE_EXCEPTION + | SR_EM | SR_GM)); + BUG_ON(ti->rsr_saved & MODE_MASK); + } + + /* + * If we stepped into a system call, we + * shouldn't do a single step after we return + * since the return address is right after the + * "scall" instruction we were told to step + * over. + */ + if ((regs->sr & MODE_MASK) == MODE_SUPERVISOR) { + pr_debug("Supervisor; no single step\n"); + clear_ti_thread_flag(ti, TIF_SINGLE_STEP); + } + + ctrl = ocd_read(DC); + ctrl &= ~(1 << OCD_DC_SS_BIT); + ocd_write(DC, ctrl); + + return regs; + } else { + printk(KERN_ERR "Unexpected OCD_DS value: 0x%08x\n", + status); + printk(KERN_ERR "Thread flags: 0x%08lx\n", ti->flags); + die("Unhandled debug trap in kernel mode", + regs, SIGTRAP); + } + } else if (status & (1 << OCD_DS_SSS_BIT)) { + /* Single step in user mode */ + code = TRAP_TRACE; - if (test_thread_flag(TIF_BREAKPOINT)) { - pr_debug("TIF_BREAKPOINT set\n"); - /* We're taking care of it */ - clear_thread_flag(TIF_BREAKPOINT); - __mtdr(DBGREG_BWC2A, 0); + ctrl = ocd_read(DC); + ctrl &= ~(1 << OCD_DC_SS_BIT); + ocd_write(DC, ctrl); } - if (test_thread_flag(TIF_SINGLE_STEP)) { - pr_debug("TIF_SINGLE_STEP set, ds = 0x%08lx\n", ds); - if (ds & DS_SSS) { - dc = __mfdr(DBGREG_DC); - dc &= ~DC_SS; - __mtdr(DBGREG_DC, dc); + pr_debug("Sending SIGTRAP: code=%d PC=0x%08lx SR=0x%08lx\n", + code, regs->pc, regs->sr); - clear_thread_flag(TIF_SINGLE_STEP); - ptrace_break(current, regs); - } - } else { - /* regular breakpoint */ - ptrace_break(current, regs); - } + clear_thread_flag(TIF_SINGLE_STEP); + _exception(SIGTRAP, regs, code, instruction_pointer(regs)); + + return regs; } diff --git a/arch/avr32/kernel/stacktrace.c b/arch/avr32/kernel/stacktrace.c new file mode 100644 index 000000000000..9a68190bbffd --- /dev/null +++ b/arch/avr32/kernel/stacktrace.c @@ -0,0 +1,53 @@ +/* + * Stack trace management functions + * + * Copyright (C) 2007 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/sched.h> +#include <linux/stacktrace.h> +#include <linux/thread_info.h> + +register unsigned long current_frame_pointer asm("r7"); + +struct stackframe { + unsigned long lr; + unsigned long fp; +}; + +/* + * Save stack-backtrace addresses into a stack_trace buffer. + */ +void save_stack_trace(struct stack_trace *trace) +{ + unsigned long low, high; + unsigned long fp; + struct stackframe *frame; + int skip = trace->skip; + + low = (unsigned long)task_stack_page(current); + high = low + THREAD_SIZE; + fp = current_frame_pointer; + + while (fp >= low && fp <= (high - 8)) { + frame = (struct stackframe *)fp; + + if (skip) { + skip--; + } else { + trace->entries[trace->nr_entries++] = frame->lr; + if (trace->nr_entries >= trace->max_entries) + break; + } + + /* + * The next frame must be at a higher address than the + * current frame. + */ + low = fp + 8; + fp = frame->fp; + } +} diff --git a/arch/avr32/kernel/traps.c b/arch/avr32/kernel/traps.c index 8a7caf8e7b45..870c075e6314 100644 --- a/arch/avr32/kernel/traps.c +++ b/arch/avr32/kernel/traps.c @@ -39,7 +39,7 @@ void NORET_TYPE die(const char *str, struct pt_regs *regs, long err) printk("FRAME_POINTER "); #endif if (current_cpu_data.features & AVR32_FEATURE_OCD) { - unsigned long did = __mfdr(DBGREG_DID); + unsigned long did = ocd_read(DID); printk("chip: 0x%03lx:0x%04lx rev %lu\n", (did >> 1) & 0x7ff, (did >> 12) & 0x7fff, diff --git a/arch/avr32/kernel/vmlinux.lds.S b/arch/avr32/kernel/vmlinux.lds.S index ce9ac9659883..11f08e35a2eb 100644 --- a/arch/avr32/kernel/vmlinux.lds.S +++ b/arch/avr32/kernel/vmlinux.lds.S @@ -77,10 +77,10 @@ SECTIONS . = 0x100; *(.scall.text) *(.irq.text) + KPROBES_TEXT TEXT_TEXT SCHED_TEXT LOCK_TEXT - KPROBES_TEXT *(.fixup) *(.gnu.warning) _etext = .; diff --git a/arch/avr32/mm/cache.c b/arch/avr32/mm/cache.c index c1233c615e67..15a4e5e142c1 100644 --- a/arch/avr32/mm/cache.c +++ b/arch/avr32/mm/cache.c @@ -122,16 +122,6 @@ void flush_icache_page(struct vm_area_struct *vma, struct page *page) } } -/* - * This one is used by copy_to_user_page() - */ -void flush_icache_user_range(struct vm_area_struct *vma, struct page *page, - unsigned long addr, int len) -{ - if (vma->vm_flags & VM_EXEC) - flush_icache_range(addr, addr + len); -} - asmlinkage int sys_cacheflush(int operation, void __user *addr, size_t len) { int ret; @@ -159,3 +149,13 @@ asmlinkage int sys_cacheflush(int operation, void __user *addr, size_t len) out: return ret; } + +void copy_to_user_page(struct vm_area_struct *vma, struct page *page, + unsigned long vaddr, void *dst, const void *src, + unsigned long len) +{ + memcpy(dst, src, len); + if (vma->vm_flags & VM_EXEC) + flush_icache_range((unsigned long)dst, + (unsigned long)dst + len); +} diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 455bd1f560aa..c6fc405a6c8e 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -714,6 +714,10 @@ config ARCH_HAS_ILOG2_U64 bool default n +config ARCH_SUPPORTS_OPROFILE + bool + default y if !MIPS_MT_SMTC + config GENERIC_FIND_NEXT_BIT bool default y diff --git a/arch/mips/au1000/common/dbdma.c b/arch/mips/au1000/common/dbdma.c index 9d6ad43fded6..edf91f41a786 100644 --- a/arch/mips/au1000/common/dbdma.c +++ b/arch/mips/au1000/common/dbdma.c @@ -859,7 +859,7 @@ dbdma_interrupt(int irq, void *dev_id) intstat = dbdma_gptr->ddma_intstat; au_sync(); - chan_index = ffs(intstat); + chan_index = __ffs(intstat); ctp = chan_tab_ptr[chan_index]; cp = ctp->chan_ptr; diff --git a/arch/mips/au1000/common/irq.c b/arch/mips/au1000/common/irq.c index ddfb7f0a17a6..3c7714f057ac 100644 --- a/arch/mips/au1000/common/irq.c +++ b/arch/mips/au1000/common/irq.c @@ -462,9 +462,9 @@ static void intc0_req0_irqdispatch(void) return; } #endif - bit = ffs(intc0_req0); + bit = __ffs(intc0_req0); intc0_req0 &= ~(1 << bit); - do_IRQ(MIPS_CPU_IRQ_BASE + bit); + do_IRQ(AU1000_INTC0_INT_BASE + bit); } @@ -478,9 +478,9 @@ static void intc0_req1_irqdispatch(void) if (!intc0_req1) return; - bit = ffs(intc0_req1); + bit = __ffs(intc0_req1); intc0_req1 &= ~(1 << bit); - do_IRQ(bit); + do_IRQ(AU1000_INTC0_INT_BASE + bit); } @@ -498,9 +498,9 @@ static void intc1_req0_irqdispatch(void) if (!intc1_req0) return; - bit = ffs(intc1_req0); + bit = __ffs(intc1_req0); intc1_req0 &= ~(1 << bit); - do_IRQ(MIPS_CPU_IRQ_BASE + 32 + bit); + do_IRQ(AU1000_INTC1_INT_BASE + bit); } @@ -514,9 +514,9 @@ static void intc1_req1_irqdispatch(void) if (!intc1_req1) return; - bit = ffs(intc1_req1); + bit = __ffs(intc1_req1); intc1_req1 &= ~(1 << bit); - do_IRQ(MIPS_CPU_IRQ_BASE + 32 + bit); + do_IRQ(AU1000_INTC1_INT_BASE + bit); } asmlinkage void plat_irq_dispatch(void) diff --git a/arch/mips/au1000/pb1200/irqmap.c b/arch/mips/au1000/pb1200/irqmap.c index c096be4ed4e7..8fcd0df86f93 100644 --- a/arch/mips/au1000/pb1200/irqmap.c +++ b/arch/mips/au1000/pb1200/irqmap.c @@ -74,7 +74,7 @@ irqreturn_t pb1200_cascade_handler( int irq, void *dev_id) bcsr->int_status = bisr; for( ; bisr; bisr &= (bisr-1) ) { - extirq_nr = PB1200_INT_BEGIN + ffs(bisr); + extirq_nr = PB1200_INT_BEGIN + __ffs(bisr); /* Ack and dispatch IRQ */ do_IRQ(extirq_nr); } diff --git a/arch/mips/oprofile/op_model_mipsxx.c b/arch/mips/oprofile/op_model_mipsxx.c index 423bc2c473df..bdfa07aecd97 100644 --- a/arch/mips/oprofile/op_model_mipsxx.c +++ b/arch/mips/oprofile/op_model_mipsxx.c @@ -6,6 +6,7 @@ * Copyright (C) 2004, 05, 06 by Ralf Baechle * Copyright (C) 2005 by MIPS Technologies, Inc. */ +#include <linux/cpumask.h> #include <linux/oprofile.h> #include <linux/interrupt.h> #include <linux/smp.h> @@ -33,11 +34,45 @@ #ifdef CONFIG_MIPS_MT_SMP #define WHAT (M_TC_EN_VPE | M_PERFCTL_VPEID(smp_processor_id())) #define vpe_id() smp_processor_id() + +/* + * The number of bits to shift to convert between counters per core and + * counters per VPE. There is no reasonable interface atm to obtain the + * number of VPEs used by Linux and in the 34K this number is fixed to two + * anyways so we hardcore a few things here for the moment. The way it's + * done here will ensure that oprofile VSMP kernel will run right on a lesser + * core like a 24K also or with maxcpus=1. + */ +static inline unsigned int vpe_shift(void) +{ + if (num_possible_cpus() > 1) + return 1; + + return 0; +} + #else + #define WHAT 0 #define vpe_id() 0 + +static inline unsigned int vpe_shift(void) +{ + return 0; +} + #endif +static inline unsigned int counters_total_to_per_cpu(unsigned int counters) +{ + return counters >> vpe_shift(); +} + +static inline unsigned int counters_per_cpu_to_total(unsigned int counters) +{ + return counters << vpe_shift(); +} + #define __define_perf_accessors(r, n, np) \ \ static inline unsigned int r_c0_ ## r ## n(void) \ @@ -269,9 +304,7 @@ static int __init mipsxx_init(void) reset_counters(counters); -#ifdef CONFIG_MIPS_MT_SMP - counters >>= 1; -#endif + counters = counters_total_to_per_cpu(counters); op_model_mipsxx_ops.num_counters = counters; switch (current_cpu_type()) { @@ -330,9 +363,8 @@ static int __init mipsxx_init(void) static void mipsxx_exit(void) { int counters = op_model_mipsxx_ops.num_counters; -#ifdef CONFIG_MIPS_MT_SMP - counters <<= 1; -#endif + + counters = counters_per_cpu_to_total(counters); reset_counters(counters); perf_irq = null_perf_irq; diff --git a/arch/mips/pci/pci-bcm1480.c b/arch/mips/pci/pci-bcm1480.c index 5443ea3596f8..47f316c86ab1 100644 --- a/arch/mips/pci/pci-bcm1480.c +++ b/arch/mips/pci/pci-bcm1480.c @@ -76,8 +76,10 @@ static inline void WRITECFG32(u32 addr, u32 data) int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) { - This is b0rked. - return dev->irq; + if (pin == 0) + return -1; + + return K_BCM1480_INT_PCI_INTA - 1 + pin; } /* Do platform specific device initialization at pci_enable_device() time */ diff --git a/arch/parisc/Makefile b/arch/parisc/Makefile index ae4a9b3d4fd6..e574de4efb36 100644 --- a/arch/parisc/Makefile +++ b/arch/parisc/Makefile @@ -70,7 +70,7 @@ kernel-y := mm/ kernel/ math-emu/ kernel/init_task.o kernel-$(CONFIG_HPUX) += hpux/ core-y += $(addprefix arch/parisc/, $(kernel-y)) -libs-y += arch/parisc/lib/ +libs-y += arch/parisc/lib/ `$(CC) -print-libgcc-file-name` drivers-$(CONFIG_OPROFILE) += arch/parisc/oprofile/ diff --git a/arch/parisc/kernel/firmware.c b/arch/parisc/kernel/firmware.c index fd6552c4c08c..4ab83d56974d 100644 --- a/arch/parisc/kernel/firmware.c +++ b/arch/parisc/kernel/firmware.c @@ -1082,76 +1082,56 @@ void pdc_io_reset_devices(void) /** - * pdc_iodc_putc - Console character print using IODC. - * @c: the character to output. + * pdc_iodc_print - Console print using IODC. + * @str: the string to output. + * @count: length of str * * Note that only these special chars are architected for console IODC io: * BEL, BS, CR, and LF. Others are passed through. * Since the HP console requires CR+LF to perform a 'newline', we translate * "\n" to "\r\n". */ -void pdc_iodc_putc(unsigned char c) +int pdc_iodc_print(unsigned char *str, unsigned count) { - /* XXX Should we spinlock posx usage */ - static int posx; /* for simple TAB-Simulation... */ - static int __attribute__((aligned(8))) iodc_retbuf[32]; - static char __attribute__((aligned(64))) iodc_dbuf[4096]; - unsigned int n; + /* XXX Should we spinlock posx usage */ + static int posx; /* for simple TAB-Simulation... */ + int __attribute__((aligned(8))) iodc_retbuf[32]; + char __attribute__((aligned(64))) iodc_dbuf[4096]; + unsigned int i; unsigned long flags; - switch (c) { - case '\n': - iodc_dbuf[0] = '\r'; - iodc_dbuf[1] = '\n'; - n = 2; - posx = 0; - break; - case '\t': - pdc_iodc_putc(' '); - while (posx & 7) /* expand TAB */ - pdc_iodc_putc(' '); - return; /* return since IODC can't handle this */ - case '\b': - posx-=2; /* BS */ - default: - iodc_dbuf[0] = c; - n = 1; - posx++; - break; - } + memset(iodc_dbuf, 0, 4096); + for (i = 0; i < count && i < 2048;) { + switch(str[i]) { + case '\n': + iodc_dbuf[i+0] = '\r'; + iodc_dbuf[i+1] = '\n'; + i += 2; + posx = 0; + break; + case '\t': + while (posx & 7) { + iodc_dbuf[i] = ' '; + i++, posx++; + } + break; + case '\b': /* BS */ + posx -= 2; + default: + iodc_dbuf[i] = str[i]; + i++, posx++; + break; + } + } spin_lock_irqsave(&pdc_lock, flags); real32_call(PAGE0->mem_cons.iodc_io, (unsigned long)PAGE0->mem_cons.hpa, ENTRY_IO_COUT, PAGE0->mem_cons.spa, __pa(PAGE0->mem_cons.dp.layers), - __pa(iodc_retbuf), 0, __pa(iodc_dbuf), n, 0); + __pa(iodc_retbuf), 0, __pa(iodc_dbuf), i, 0); spin_unlock_irqrestore(&pdc_lock, flags); -} -/** - * pdc_iodc_outc - Console character print using IODC (without conversions). - * @c: the character to output. - * - * Write the character directly to the IODC console. - */ -void pdc_iodc_outc(unsigned char c) -{ - unsigned int n; - unsigned long flags; - - /* fill buffer with one caracter and print it */ - static int __attribute__((aligned(8))) iodc_retbuf[32]; - static char __attribute__((aligned(64))) iodc_dbuf[4096]; - - n = 1; - iodc_dbuf[0] = c; - - spin_lock_irqsave(&pdc_lock, flags); - real32_call(PAGE0->mem_cons.iodc_io, - (unsigned long)PAGE0->mem_cons.hpa, ENTRY_IO_COUT, - PAGE0->mem_cons.spa, __pa(PAGE0->mem_cons.dp.layers), - __pa(iodc_retbuf), 0, __pa(iodc_dbuf), n, 0); - spin_unlock_irqrestore(&pdc_lock, flags); + return i; } /** diff --git a/arch/parisc/kernel/irq.c b/arch/parisc/kernel/irq.c index 76ce5e3b0050..23ef950df008 100644 --- a/arch/parisc/kernel/irq.c +++ b/arch/parisc/kernel/irq.c @@ -397,7 +397,7 @@ static void claim_cpu_irqs(void) } irq_desc[TIMER_IRQ].action = &timer_action; - irq_desc[TIMER_IRQ].status |= IRQ_PER_CPU; + irq_desc[TIMER_IRQ].status = IRQ_PER_CPU; #ifdef CONFIG_SMP irq_desc[IPI_IRQ].action = &ipi_action; irq_desc[IPI_IRQ].status = IRQ_PER_CPU; diff --git a/arch/parisc/kernel/parisc_ksyms.c b/arch/parisc/kernel/parisc_ksyms.c index 671ee5b9950c..7aca704e96f0 100644 --- a/arch/parisc/kernel/parisc_ksyms.c +++ b/arch/parisc/kernel/parisc_ksyms.c @@ -122,9 +122,31 @@ EXPORT_SYMBOL($$divI_12); EXPORT_SYMBOL($$divI_14); EXPORT_SYMBOL($$divI_15); +extern void __ashrdi3(void); +extern void __ashldi3(void); +extern void __lshrdi3(void); +extern void __muldi3(void); + +EXPORT_SYMBOL(__ashrdi3); +EXPORT_SYMBOL(__ashldi3); +EXPORT_SYMBOL(__lshrdi3); +EXPORT_SYMBOL(__muldi3); + asmlinkage void * __canonicalize_funcptr_for_compare(void *); EXPORT_SYMBOL(__canonicalize_funcptr_for_compare); +#ifdef CONFIG_64BIT +extern void __divdi3(void); +extern void __udivdi3(void); +extern void __umoddi3(void); +extern void __moddi3(void); + +EXPORT_SYMBOL(__divdi3); +EXPORT_SYMBOL(__udivdi3); +EXPORT_SYMBOL(__umoddi3); +EXPORT_SYMBOL(__moddi3); +#endif + #ifndef CONFIG_64BIT extern void $$dyncall(void); EXPORT_SYMBOL($$dyncall); diff --git a/arch/parisc/kernel/pdc_cons.c b/arch/parisc/kernel/pdc_cons.c index aab05767427c..33b1f84441b1 100644 --- a/arch/parisc/kernel/pdc_cons.c +++ b/arch/parisc/kernel/pdc_cons.c @@ -55,13 +55,7 @@ static void pdc_console_write(struct console *co, const char *s, unsigned count) { - while(count--) - pdc_iodc_putc(*s++); -} - -void pdc_outc(unsigned char c) -{ - pdc_iodc_outc(c); + pdc_iodc_print(s, count); } void pdc_printf(const char *fmt, ...) @@ -74,8 +68,7 @@ void pdc_printf(const char *fmt, ...) len = vscnprintf(buf, sizeof(buf), fmt, args); va_end(args); - for (i = 0; i < len; i++) - pdc_iodc_outc(buf[i]); + pdc_iodc_print(buf, len); } int pdc_console_poll_key(struct console *co) diff --git a/arch/parisc/lib/Makefile b/arch/parisc/lib/Makefile index 7ce406c7daf5..5f2e6904d14a 100644 --- a/arch/parisc/lib/Makefile +++ b/arch/parisc/lib/Makefile @@ -4,4 +4,4 @@ lib-y := lusercopy.o bitops.o checksum.o io.o memset.o fixup.o memcpy.o -obj-y := libgcc/ milli/ iomap.o +obj-y := iomap.o diff --git a/arch/parisc/lib/libgcc/Makefile b/arch/parisc/lib/libgcc/Makefile deleted file mode 100644 index b67a85ad9c87..000000000000 --- a/arch/parisc/lib/libgcc/Makefile +++ /dev/null @@ -1,4 +0,0 @@ -obj-y := __ashldi3.o __ashrdi3.o __clzsi2.o __divdi3.o __divsi3.o \ - __lshrdi3.o __moddi3.o __modsi3.o __udivdi3.o \ - __udivmoddi4.o __udivmodsi4.o __udivsi3.o \ - __umoddi3.o __umodsi3.o __muldi3.o __umulsidi3.o diff --git a/arch/parisc/lib/libgcc/__ashldi3.c b/arch/parisc/lib/libgcc/__ashldi3.c deleted file mode 100644 index a14a257abb2b..000000000000 --- a/arch/parisc/lib/libgcc/__ashldi3.c +++ /dev/null @@ -1,19 +0,0 @@ -#include "libgcc.h" - -u64 __ashldi3(u64 v, int cnt) -{ - int c = cnt & 31; - u32 vl = (u32) v; - u32 vh = (u32) (v >> 32); - - if (cnt & 32) { - vh = (vl << c); - vl = 0; - } else { - vh = (vh << c) + (vl >> (32 - c)); - vl = (vl << c); - } - - return ((u64) vh << 32) + vl; -} -EXPORT_SYMBOL(__ashldi3); diff --git a/arch/parisc/lib/libgcc/__ashrdi3.c b/arch/parisc/lib/libgcc/__ashrdi3.c deleted file mode 100644 index 8636a5aa4f77..000000000000 --- a/arch/parisc/lib/libgcc/__ashrdi3.c +++ /dev/null @@ -1,19 +0,0 @@ -#include "libgcc.h" - -u64 __ashrdi3(u64 v, int cnt) -{ - int c = cnt & 31; - u32 vl = (u32) v; - u32 vh = (u32) (v >> 32); - - if (cnt & 32) { - vl = ((s32) vh >> c); - vh = (s32) vh >> 31; - } else { - vl = (vl >> c) + (vh << (32 - c)); - vh = ((s32) vh >> c); - } - - return ((u64) vh << 32) + vl; -} -EXPORT_SYMBOL(__ashrdi3); diff --git a/arch/parisc/lib/libgcc/__clzsi2.c b/arch/parisc/lib/libgcc/__clzsi2.c deleted file mode 100644 index a7aa2f55a9c6..000000000000 --- a/arch/parisc/lib/libgcc/__clzsi2.c +++ /dev/null @@ -1,30 +0,0 @@ -#include "libgcc.h" - -u32 __clzsi2(u32 v) -{ - int p = 31; - - if (v & 0xffff0000) { - p -= 16; - v >>= 16; - } - if (v & 0xff00) { - p -= 8; - v >>= 8; - } - if (v & 0xf0) { - p -= 4; - v >>= 4; - } - if (v & 0xc) { - p -= 2; - v >>= 2; - } - if (v & 0x2) { - p -= 1; - v >>= 1; - } - - return p; -} -EXPORT_SYMBOL(__clzsi2); diff --git a/arch/parisc/lib/libgcc/__divdi3.c b/arch/parisc/lib/libgcc/__divdi3.c deleted file mode 100644 index f23c6fe2838b..000000000000 --- a/arch/parisc/lib/libgcc/__divdi3.c +++ /dev/null @@ -1,23 +0,0 @@ -#include "libgcc.h" - -s64 __divdi3(s64 num, s64 den) -{ - int minus = 0; - s64 v; - - if (num < 0) { - num = -num; - minus = 1; - } - if (den < 0) { - den = -den; - minus ^= 1; - } - - v = __udivmoddi4(num, den, NULL); - if (minus) - v = -v; - - return v; -} -EXPORT_SYMBOL(__divdi3); diff --git a/arch/parisc/lib/libgcc/__divsi3.c b/arch/parisc/lib/libgcc/__divsi3.c deleted file mode 100644 index 730fb530680d..000000000000 --- a/arch/parisc/lib/libgcc/__divsi3.c +++ /dev/null @@ -1,23 +0,0 @@ -#include "libgcc.h" - -s32 __divsi3(s32 num, s32 den) -{ - int minus = 0; - s32 v; - - if (num < 0) { - num = -num; - minus = 1; - } - if (den < 0) { - den = -den; - minus ^= 1; - } - - v = __udivmodsi4(num, den, NULL); - if (minus) - v = -v; - - return v; -} -EXPORT_SYMBOL(__divsi3); diff --git a/arch/parisc/lib/libgcc/__lshrdi3.c b/arch/parisc/lib/libgcc/__lshrdi3.c deleted file mode 100644 index 4a820708ec57..000000000000 --- a/arch/parisc/lib/libgcc/__lshrdi3.c +++ /dev/null @@ -1,19 +0,0 @@ -#include "libgcc.h" - -u64 __lshrdi3(u64 v, int cnt) -{ - int c = cnt & 31; - u32 vl = (u32) v; - u32 vh = (u32) (v >> 32); - - if (cnt & 32) { - vl = (vh >> c); - vh = 0; - } else { - vl = (vl >> c) + (vh << (32 - c)); - vh = (vh >> c); - } - - return ((u64) vh << 32) + vl; -} -EXPORT_SYMBOL(__lshrdi3); diff --git a/arch/parisc/lib/libgcc/__moddi3.c b/arch/parisc/lib/libgcc/__moddi3.c deleted file mode 100644 index ed64bbafc989..000000000000 --- a/arch/parisc/lib/libgcc/__moddi3.c +++ /dev/null @@ -1,23 +0,0 @@ -#include "libgcc.h" - -s64 __moddi3(s64 num, s64 den) -{ - int minus = 0; - s64 v; - - if (num < 0) { - num = -num; - minus = 1; - } - if (den < 0) { - den = -den; - minus ^= 1; - } - - (void)__udivmoddi4(num, den, (u64 *) & v); - if (minus) - v = -v; - - return v; -} -EXPORT_SYMBOL(__moddi3); diff --git a/arch/parisc/lib/libgcc/__modsi3.c b/arch/parisc/lib/libgcc/__modsi3.c deleted file mode 100644 index 62f773efaeea..000000000000 --- a/arch/parisc/lib/libgcc/__modsi3.c +++ /dev/null @@ -1,23 +0,0 @@ -#include "libgcc.h" - -s32 __modsi3(s32 num, s32 den) -{ - int minus = 0; - s32 v; - - if (num < 0) { - num = -num; - minus = 1; - } - if (den < 0) { - den = -den; - minus ^= 1; - } - - (void)__udivmodsi4(num, den, (u32 *) & v); - if (minus) - v = -v; - - return v; -} -EXPORT_SYMBOL(__modsi3); diff --git a/arch/parisc/lib/libgcc/__muldi3.c b/arch/parisc/lib/libgcc/__muldi3.c deleted file mode 100644 index 3308abdd5580..000000000000 --- a/arch/parisc/lib/libgcc/__muldi3.c +++ /dev/null @@ -1,22 +0,0 @@ -#include "libgcc.h" - -union DWunion { - struct { - s32 high; - s32 low; - } s; - s64 ll; -}; - -s64 __muldi3(s64 u, s64 v) -{ - const union DWunion uu = { .ll = u }; - const union DWunion vv = { .ll = v }; - union DWunion w = { .ll = __umulsidi3(uu.s.low, vv.s.low) }; - - w.s.high += ((u32)uu.s.low * (u32)vv.s.high - + (u32)uu.s.high * (u32)vv.s.low); - - return w.ll; -} -EXPORT_SYMBOL(__muldi3); diff --git a/arch/parisc/lib/libgcc/__udivdi3.c b/arch/parisc/lib/libgcc/__udivdi3.c deleted file mode 100644 index 740023d690f5..000000000000 --- a/arch/parisc/lib/libgcc/__udivdi3.c +++ /dev/null @@ -1,7 +0,0 @@ -#include "libgcc.h" - -u64 __udivdi3(u64 num, u64 den) -{ - return __udivmoddi4(num, den, NULL); -} -EXPORT_SYMBOL(__udivdi3); diff --git a/arch/parisc/lib/libgcc/__udivmoddi4.c b/arch/parisc/lib/libgcc/__udivmoddi4.c deleted file mode 100644 index 2df0caa5a7d8..000000000000 --- a/arch/parisc/lib/libgcc/__udivmoddi4.c +++ /dev/null @@ -1,31 +0,0 @@ -#include "libgcc.h" - -u64 __udivmoddi4(u64 num, u64 den, u64 * rem_p) -{ - u64 quot = 0, qbit = 1; - - if (den == 0) { - BUG(); - } - - /* Left-justify denominator and count shift */ - while ((s64) den >= 0) { - den <<= 1; - qbit <<= 1; - } - - while (qbit) { - if (den <= num) { - num -= den; - quot += qbit; - } - den >>= 1; - qbit >>= 1; - } - - if (rem_p) - *rem_p = num; - - return quot; -} -EXPORT_SYMBOL(__udivmoddi4); diff --git a/arch/parisc/lib/libgcc/__udivmodsi4.c b/arch/parisc/lib/libgcc/__udivmodsi4.c deleted file mode 100644 index 2a2fc28b2026..000000000000 --- a/arch/parisc/lib/libgcc/__udivmodsi4.c +++ /dev/null @@ -1,31 +0,0 @@ -#include "libgcc.h" - -u32 __udivmodsi4(u32 num, u32 den, u32 * rem_p) -{ - u32 quot = 0, qbit = 1; - - if (den == 0) { - BUG(); - } - - /* Left-justify denominator and count shift */ - while ((s32) den >= 0) { - den <<= 1; - qbit <<= 1; - } - - while (qbit) { - if (den <= num) { - num -= den; - quot += qbit; - } - den >>= 1; - qbit >>= 1; - } - - if (rem_p) - *rem_p = num; - - return quot; -} -EXPORT_SYMBOL(__udivmodsi4); diff --git a/arch/parisc/lib/libgcc/__udivsi3.c b/arch/parisc/lib/libgcc/__udivsi3.c deleted file mode 100644 index 756a44164e90..000000000000 --- a/arch/parisc/lib/libgcc/__udivsi3.c +++ /dev/null @@ -1,7 +0,0 @@ -#include "libgcc.h" - -u32 __udivsi3(u32 num, u32 den) -{ - return __udivmodsi4(num, den, NULL); -} -EXPORT_SYMBOL(__udivsi3); diff --git a/arch/parisc/lib/libgcc/__umoddi3.c b/arch/parisc/lib/libgcc/__umoddi3.c deleted file mode 100644 index ac744e948bc1..000000000000 --- a/arch/parisc/lib/libgcc/__umoddi3.c +++ /dev/null @@ -1,10 +0,0 @@ -#include "libgcc.h" - -u64 __umoddi3(u64 num, u64 den) -{ - u64 v; - - (void)__udivmoddi4(num, den, &v); - return v; -} -EXPORT_SYMBOL(__umoddi3); diff --git a/arch/parisc/lib/libgcc/__umodsi3.c b/arch/parisc/lib/libgcc/__umodsi3.c deleted file mode 100644 index 51f55aa89f9a..000000000000 --- a/arch/parisc/lib/libgcc/__umodsi3.c +++ /dev/null @@ -1,10 +0,0 @@ -#include "libgcc.h" - -u32 __umodsi3(u32 num, u32 den) -{ - u32 v; - - (void)__udivmodsi4(num, den, &v); - return v; -} -EXPORT_SYMBOL(__umodsi3); diff --git a/arch/parisc/lib/libgcc/__umulsidi3.c b/arch/parisc/lib/libgcc/__umulsidi3.c deleted file mode 100644 index 396f669164d4..000000000000 --- a/arch/parisc/lib/libgcc/__umulsidi3.c +++ /dev/null @@ -1,46 +0,0 @@ -#include "libgcc.h" - -#define __ll_B ((u32) 1 << (32 / 2)) -#define __ll_lowpart(t) ((u32) (t) & (__ll_B - 1)) -#define __ll_highpart(t) ((u32) (t) >> 16) - -#define umul_ppmm(w1, w0, u, v) \ - do { \ - u32 __x0, __x1, __x2, __x3; \ - u16 __ul, __vl, __uh, __vh; \ - \ - __ul = __ll_lowpart (u); \ - __uh = __ll_highpart (u); \ - __vl = __ll_lowpart (v); \ - __vh = __ll_highpart (v); \ - \ - __x0 = (u32) __ul * __vl; \ - __x1 = (u32) __ul * __vh; \ - __x2 = (u32) __uh * __vl; \ - __x3 = (u32) __uh * __vh; \ - \ - __x1 += __ll_highpart (__x0);/* this can't give carry */ \ - __x1 += __x2; /* but this indeed can */ \ - if (__x1 < __x2) /* did we get it? */ \ - __x3 += __ll_B; /* yes, add it in the proper pos. */ \ - \ - (w1) = __x3 + __ll_highpart (__x1); \ - (w0) = __ll_lowpart (__x1) * __ll_B + __ll_lowpart (__x0); \ - } while (0) - -union DWunion { - struct { - s32 high; - s32 low; - } s; - s64 ll; -}; - -u64 __umulsidi3(u32 u, u32 v) -{ - union DWunion __w; - - umul_ppmm(__w.s.high, __w.s.low, u, v); - - return __w.ll; -} diff --git a/arch/parisc/lib/libgcc/libgcc.h b/arch/parisc/lib/libgcc/libgcc.h deleted file mode 100644 index 5a6f7a510fbd..000000000000 --- a/arch/parisc/lib/libgcc/libgcc.h +++ /dev/null @@ -1,32 +0,0 @@ -#ifndef _PA_LIBGCC_H_ -#define _PA_LIBGCC_H_ - -#include <linux/types.h> -#include <linux/module.h> - -/* Cribbed from klibc/libgcc/ */ -u64 __ashldi3(u64 v, int cnt); -u64 __ashrdi3(u64 v, int cnt); - -u32 __clzsi2(u32 v); - -s64 __divdi3(s64 num, s64 den); -s32 __divsi3(s32 num, s32 den); - -u64 __lshrdi3(u64 v, int cnt); - -s64 __moddi3(s64 num, s64 den); -s32 __modsi3(s32 num, s32 den); - -u64 __udivdi3(u64 num, u64 den); -u32 __udivsi3(u32 num, u32 den); - -u64 __udivmoddi4(u64 num, u64 den, u64 * rem_p); -u32 __udivmodsi4(u32 num, u32 den, u32 * rem_p); - -u64 __umulsidi3(u32 u, u32 v); - -u64 __umoddi3(u64 num, u64 den); -u32 __umodsi3(u32 num, u32 den); - -#endif /*_PA_LIBGCC_H_*/ diff --git a/arch/parisc/lib/milli/Makefile b/arch/parisc/lib/milli/Makefile deleted file mode 100644 index 9b24e9b1f3cb..000000000000 --- a/arch/parisc/lib/milli/Makefile +++ /dev/null @@ -1 +0,0 @@ -obj-y := dyncall.o divI.o divU.o remI.o remU.o div_const.o mulI.o diff --git a/arch/parisc/lib/milli/divI.S b/arch/parisc/lib/milli/divI.S deleted file mode 100644 index ac106b7b6f24..000000000000 --- a/arch/parisc/lib/milli/divI.S +++ /dev/null @@ -1,254 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#include "milli.h" - -#ifdef L_divI -/* ROUTINES: $$divI, $$divoI - - Single precision divide for signed binary integers. - - The quotient is truncated towards zero. - The sign of the quotient is the XOR of the signs of the dividend and - divisor. - Divide by zero is trapped. - Divide of -2**31 by -1 is trapped for $$divoI but not for $$divI. - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = quotient - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: - . divisor is zero (traps with ADDIT,= 0,25,0) - . dividend==-2**31 and divisor==-1 and routine is $$divoI - . (traps with ADDO 26,25,0) - . Changes memory at the following places: - . NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Branchs to other millicode routines using BE - . $$div_# for # being 2,3,4,5,6,7,8,9,10,12,14,15 - . - . For selected divisors, calls a divide by constant routine written by - . Karl Pettis. Eligible divisors are 1..15 excluding 11 and 13. - . - . The only overflow case is -2**31 divided by -1. - . Both routines return -2**31 but only $$divoI traps. */ - -RDEFINE(temp,r1) -RDEFINE(retreg,ret1) /* r29 */ -RDEFINE(temp1,arg0) - SUBSPA_MILLI_DIV - ATTR_MILLI - .import $$divI_2,millicode - .import $$divI_3,millicode - .import $$divI_4,millicode - .import $$divI_5,millicode - .import $$divI_6,millicode - .import $$divI_7,millicode - .import $$divI_8,millicode - .import $$divI_9,millicode - .import $$divI_10,millicode - .import $$divI_12,millicode - .import $$divI_14,millicode - .import $$divI_15,millicode - .export $$divI,millicode - .export $$divoI,millicode - .proc - .callinfo millicode - .entry -GSYM($$divoI) - comib,=,n -1,arg1,LREF(negative1) /* when divisor == -1 */ -GSYM($$divI) - ldo -1(arg1),temp /* is there at most one bit set ? */ - and,<> arg1,temp,r0 /* if not, don't use power of 2 divide */ - addi,> 0,arg1,r0 /* if divisor > 0, use power of 2 divide */ - b,n LREF(neg_denom) -LSYM(pow2) - addi,>= 0,arg0,retreg /* if numerator is negative, add the */ - add arg0,temp,retreg /* (denominaotr -1) to correct for shifts */ - extru,= arg1,15,16,temp /* test denominator with 0xffff0000 */ - extrs retreg,15,16,retreg /* retreg = retreg >> 16 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 16) */ - ldi 0xcc,temp1 /* setup 0xcc in temp1 */ - extru,= arg1,23,8,temp /* test denominator with 0xff00 */ - extrs retreg,23,24,retreg /* retreg = retreg >> 8 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 8) */ - ldi 0xaa,temp /* setup 0xaa in temp */ - extru,= arg1,27,4,r0 /* test denominator with 0xf0 */ - extrs retreg,27,28,retreg /* retreg = retreg >> 4 */ - and,= arg1,temp1,r0 /* test denominator with 0xcc */ - extrs retreg,29,30,retreg /* retreg = retreg >> 2 */ - and,= arg1,temp,r0 /* test denominator with 0xaa */ - extrs retreg,30,31,retreg /* retreg = retreg >> 1 */ - MILLIRETN -LSYM(neg_denom) - addi,< 0,arg1,r0 /* if arg1 >= 0, it's not power of 2 */ - b,n LREF(regular_seq) - sub r0,arg1,temp /* make denominator positive */ - comb,=,n arg1,temp,LREF(regular_seq) /* test against 0x80000000 and 0 */ - ldo -1(temp),retreg /* is there at most one bit set ? */ - and,= temp,retreg,r0 /* if so, the denominator is power of 2 */ - b,n LREF(regular_seq) - sub r0,arg0,retreg /* negate numerator */ - comb,=,n arg0,retreg,LREF(regular_seq) /* test against 0x80000000 */ - copy retreg,arg0 /* set up arg0, arg1 and temp */ - copy temp,arg1 /* before branching to pow2 */ - b LREF(pow2) - ldo -1(arg1),temp -LSYM(regular_seq) - comib,>>=,n 15,arg1,LREF(small_divisor) - add,>= 0,arg0,retreg /* move dividend, if retreg < 0, */ -LSYM(normal) - subi 0,retreg,retreg /* make it positive */ - sub 0,arg1,temp /* clear carry, */ - /* negate the divisor */ - ds 0,temp,0 /* set V-bit to the comple- */ - /* ment of the divisor sign */ - add retreg,retreg,retreg /* shift msb bit into carry */ - ds r0,arg1,temp /* 1st divide step, if no carry */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 2nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 3rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 4th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 5th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 6th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 7th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 8th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 9th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 10th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 11th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 12th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 13th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 14th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 15th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 16th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 17th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 18th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 19th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 20th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 21st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 22nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 23rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 24th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 25th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 26th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 27th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 28th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 29th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 30th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 31st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 32nd divide step, */ - addc retreg,retreg,retreg /* shift last retreg bit into retreg */ - xor,>= arg0,arg1,0 /* get correct sign of quotient */ - sub 0,retreg,retreg /* based on operand signs */ - MILLIRETN - nop - -LSYM(small_divisor) - -#if defined(CONFIG_64BIT) -/* Clear the upper 32 bits of the arg1 register. We are working with */ -/* small divisors (and 32-bit integers) We must not be mislead */ -/* by "1" bits left in the upper 32 bits. */ - depd %r0,31,32,%r25 -#endif - blr,n arg1,r0 - nop -/* table for divisor == 0,1, ... ,15 */ - addit,= 0,arg1,r0 /* trap if divisor == 0 */ - nop - MILLIRET /* divisor == 1 */ - copy arg0,retreg - MILLI_BEN($$divI_2) /* divisor == 2 */ - nop - MILLI_BEN($$divI_3) /* divisor == 3 */ - nop - MILLI_BEN($$divI_4) /* divisor == 4 */ - nop - MILLI_BEN($$divI_5) /* divisor == 5 */ - nop - MILLI_BEN($$divI_6) /* divisor == 6 */ - nop - MILLI_BEN($$divI_7) /* divisor == 7 */ - nop - MILLI_BEN($$divI_8) /* divisor == 8 */ - nop - MILLI_BEN($$divI_9) /* divisor == 9 */ - nop - MILLI_BEN($$divI_10) /* divisor == 10 */ - nop - b LREF(normal) /* divisor == 11 */ - add,>= 0,arg0,retreg - MILLI_BEN($$divI_12) /* divisor == 12 */ - nop - b LREF(normal) /* divisor == 13 */ - add,>= 0,arg0,retreg - MILLI_BEN($$divI_14) /* divisor == 14 */ - nop - MILLI_BEN($$divI_15) /* divisor == 15 */ - nop - -LSYM(negative1) - sub 0,arg0,retreg /* result is negation of dividend */ - MILLIRET - addo arg0,arg1,r0 /* trap iff dividend==0x80000000 && divisor==-1 */ - .exit - .procend - .end -#endif diff --git a/arch/parisc/lib/milli/divU.S b/arch/parisc/lib/milli/divU.S deleted file mode 100644 index 9287fe2546fa..000000000000 --- a/arch/parisc/lib/milli/divU.S +++ /dev/null @@ -1,235 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#include "milli.h" - -#ifdef L_divU -/* ROUTINE: $$divU - . - . Single precision divide for unsigned integers. - . - . Quotient is truncated towards zero. - . Traps on divide by zero. - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = quotient - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: - . divisor is zero - . Changes memory at the following places: - . NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Does not create a stack frame. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Branchs to other millicode routines using BE: - . $$divU_# for 3,5,6,7,9,10,12,14,15 - . - . For selected small divisors calls the special divide by constant - . routines written by Karl Pettis. These are: 3,5,6,7,9,10,12,14,15. */ - -RDEFINE(temp,r1) -RDEFINE(retreg,ret1) /* r29 */ -RDEFINE(temp1,arg0) - SUBSPA_MILLI_DIV - ATTR_MILLI - .export $$divU,millicode - .import $$divU_3,millicode - .import $$divU_5,millicode - .import $$divU_6,millicode - .import $$divU_7,millicode - .import $$divU_9,millicode - .import $$divU_10,millicode - .import $$divU_12,millicode - .import $$divU_14,millicode - .import $$divU_15,millicode - .proc - .callinfo millicode - .entry -GSYM($$divU) -/* The subtract is not nullified since it does no harm and can be used - by the two cases that branch back to "normal". */ - ldo -1(arg1),temp /* is there at most one bit set ? */ - and,= arg1,temp,r0 /* if so, denominator is power of 2 */ - b LREF(regular_seq) - addit,= 0,arg1,0 /* trap for zero dvr */ - copy arg0,retreg - extru,= arg1,15,16,temp /* test denominator with 0xffff0000 */ - extru retreg,15,16,retreg /* retreg = retreg >> 16 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 16) */ - ldi 0xcc,temp1 /* setup 0xcc in temp1 */ - extru,= arg1,23,8,temp /* test denominator with 0xff00 */ - extru retreg,23,24,retreg /* retreg = retreg >> 8 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 8) */ - ldi 0xaa,temp /* setup 0xaa in temp */ - extru,= arg1,27,4,r0 /* test denominator with 0xf0 */ - extru retreg,27,28,retreg /* retreg = retreg >> 4 */ - and,= arg1,temp1,r0 /* test denominator with 0xcc */ - extru retreg,29,30,retreg /* retreg = retreg >> 2 */ - and,= arg1,temp,r0 /* test denominator with 0xaa */ - extru retreg,30,31,retreg /* retreg = retreg >> 1 */ - MILLIRETN - nop -LSYM(regular_seq) - comib,>= 15,arg1,LREF(special_divisor) - subi 0,arg1,temp /* clear carry, negate the divisor */ - ds r0,temp,r0 /* set V-bit to 1 */ -LSYM(normal) - add arg0,arg0,retreg /* shift msb bit into carry */ - ds r0,arg1,temp /* 1st divide step, if no carry */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 2nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 3rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 4th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 5th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 6th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 7th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 8th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 9th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 10th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 11th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 12th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 13th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 14th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 15th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 16th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 17th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 18th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 19th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 20th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 21st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 22nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 23rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 24th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 25th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 26th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 27th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 28th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 29th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 30th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 31st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 32nd divide step, */ - MILLIRET - addc retreg,retreg,retreg /* shift last retreg bit into retreg */ - -/* Handle the cases where divisor is a small constant or has high bit on. */ -LSYM(special_divisor) -/* blr arg1,r0 */ -/* comib,>,n 0,arg1,LREF(big_divisor) ; nullify previous instruction */ - -/* Pratap 8/13/90. The 815 Stirling chip set has a bug that prevents us from - generating such a blr, comib sequence. A problem in nullification. So I - rewrote this code. */ - -#if defined(CONFIG_64BIT) -/* Clear the upper 32 bits of the arg1 register. We are working with - small divisors (and 32-bit unsigned integers) We must not be mislead - by "1" bits left in the upper 32 bits. */ - depd %r0,31,32,%r25 -#endif - comib,> 0,arg1,LREF(big_divisor) - nop - blr arg1,r0 - nop - -LSYM(zero_divisor) /* this label is here to provide external visibility */ - addit,= 0,arg1,0 /* trap for zero dvr */ - nop - MILLIRET /* divisor == 1 */ - copy arg0,retreg - MILLIRET /* divisor == 2 */ - extru arg0,30,31,retreg - MILLI_BEN($$divU_3) /* divisor == 3 */ - nop - MILLIRET /* divisor == 4 */ - extru arg0,29,30,retreg - MILLI_BEN($$divU_5) /* divisor == 5 */ - nop - MILLI_BEN($$divU_6) /* divisor == 6 */ - nop - MILLI_BEN($$divU_7) /* divisor == 7 */ - nop - MILLIRET /* divisor == 8 */ - extru arg0,28,29,retreg - MILLI_BEN($$divU_9) /* divisor == 9 */ - nop - MILLI_BEN($$divU_10) /* divisor == 10 */ - nop - b LREF(normal) /* divisor == 11 */ - ds r0,temp,r0 /* set V-bit to 1 */ - MILLI_BEN($$divU_12) /* divisor == 12 */ - nop - b LREF(normal) /* divisor == 13 */ - ds r0,temp,r0 /* set V-bit to 1 */ - MILLI_BEN($$divU_14) /* divisor == 14 */ - nop - MILLI_BEN($$divU_15) /* divisor == 15 */ - nop - -/* Handle the case where the high bit is on in the divisor. - Compute: if( dividend>=divisor) quotient=1; else quotient=0; - Note: dividend>==divisor iff dividend-divisor does not borrow - and not borrow iff carry. */ -LSYM(big_divisor) - sub arg0,arg1,r0 - MILLIRET - addc r0,r0,retreg - .exit - .procend - .end -#endif diff --git a/arch/parisc/lib/milli/div_const.S b/arch/parisc/lib/milli/div_const.S deleted file mode 100644 index dd660076e944..000000000000 --- a/arch/parisc/lib/milli/div_const.S +++ /dev/null @@ -1,682 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#include "milli.h" - -#ifdef L_div_const -/* ROUTINE: $$divI_2 - . $$divI_3 $$divU_3 - . $$divI_4 - . $$divI_5 $$divU_5 - . $$divI_6 $$divU_6 - . $$divI_7 $$divU_7 - . $$divI_8 - . $$divI_9 $$divU_9 - . $$divI_10 $$divU_10 - . - . $$divI_12 $$divU_12 - . - . $$divI_14 $$divU_14 - . $$divI_15 $$divU_15 - . $$divI_16 - . $$divI_17 $$divU_17 - . - . Divide by selected constants for single precision binary integers. - - INPUT REGISTERS: - . arg0 == dividend - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = quotient - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: NONE - . Changes memory at the following places: NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Does not create a stack frame. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Calls other millicode routines using mrp: NONE - . Calls other millicode routines: NONE */ - - -/* TRUNCATED DIVISION BY SMALL INTEGERS - - We are interested in q(x) = floor(x/y), where x >= 0 and y > 0 - (with y fixed). - - Let a = floor(z/y), for some choice of z. Note that z will be - chosen so that division by z is cheap. - - Let r be the remainder(z/y). In other words, r = z - ay. - - Now, our method is to choose a value for b such that - - q'(x) = floor((ax+b)/z) - - is equal to q(x) over as large a range of x as possible. If the - two are equal over a sufficiently large range, and if it is easy to - form the product (ax), and it is easy to divide by z, then we can - perform the division much faster than the general division algorithm. - - So, we want the following to be true: - - . For x in the following range: - . - . ky <= x < (k+1)y - . - . implies that - . - . k <= (ax+b)/z < (k+1) - - We want to determine b such that this is true for all k in the - range {0..K} for some maximum K. - - Since (ax+b) is an increasing function of x, we can take each - bound separately to determine the "best" value for b. - - (ax+b)/z < (k+1) implies - - (a((k+1)y-1)+b < (k+1)z implies - - b < a + (k+1)(z-ay) implies - - b < a + (k+1)r - - This needs to be true for all k in the range {0..K}. In - particular, it is true for k = 0 and this leads to a maximum - acceptable value for b. - - b < a+r or b <= a+r-1 - - Taking the other bound, we have - - k <= (ax+b)/z implies - - k <= (aky+b)/z implies - - k(z-ay) <= b implies - - kr <= b - - Clearly, the largest range for k will be achieved by maximizing b, - when r is not zero. When r is zero, then the simplest choice for b - is 0. When r is not 0, set - - . b = a+r-1 - - Now, by construction, q'(x) = floor((ax+b)/z) = q(x) = floor(x/y) - for all x in the range: - - . 0 <= x < (K+1)y - - We need to determine what K is. Of our two bounds, - - . b < a+(k+1)r is satisfied for all k >= 0, by construction. - - The other bound is - - . kr <= b - - This is always true if r = 0. If r is not 0 (the usual case), then - K = floor((a+r-1)/r), is the maximum value for k. - - Therefore, the formula q'(x) = floor((ax+b)/z) yields the correct - answer for q(x) = floor(x/y) when x is in the range - - (0,(K+1)y-1) K = floor((a+r-1)/r) - - To be most useful, we want (K+1)y-1 = (max x) >= 2**32-1 so that - the formula for q'(x) yields the correct value of q(x) for all x - representable by a single word in HPPA. - - We are also constrained in that computing the product (ax), adding - b, and dividing by z must all be done quickly, otherwise we will be - better off going through the general algorithm using the DS - instruction, which uses approximately 70 cycles. - - For each y, there is a choice of z which satisfies the constraints - for (K+1)y >= 2**32. We may not, however, be able to satisfy the - timing constraints for arbitrary y. It seems that z being equal to - a power of 2 or a power of 2 minus 1 is as good as we can do, since - it minimizes the time to do division by z. We want the choice of z - to also result in a value for (a) that minimizes the computation of - the product (ax). This is best achieved if (a) has a regular bit - pattern (so the multiplication can be done with shifts and adds). - The value of (a) also needs to be less than 2**32 so the product is - always guaranteed to fit in 2 words. - - In actual practice, the following should be done: - - 1) For negative x, you should take the absolute value and remember - . the fact so that the result can be negated. This obviously does - . not apply in the unsigned case. - 2) For even y, you should factor out the power of 2 that divides y - . and divide x by it. You can then proceed by dividing by the - . odd factor of y. - - Here is a table of some odd values of y, and corresponding choices - for z which are "good". - - y z r a (hex) max x (hex) - - 3 2**32 1 55555555 100000001 - 5 2**32 1 33333333 100000003 - 7 2**24-1 0 249249 (infinite) - 9 2**24-1 0 1c71c7 (infinite) - 11 2**20-1 0 1745d (infinite) - 13 2**24-1 0 13b13b (infinite) - 15 2**32 1 11111111 10000000d - 17 2**32 1 f0f0f0f 10000000f - - If r is 1, then b = a+r-1 = a. This simplifies the computation - of (ax+b), since you can compute (x+1)(a) instead. If r is 0, - then b = 0 is ok to use which simplifies (ax+b). - - The bit patterns for 55555555, 33333333, and 11111111 are obviously - very regular. The bit patterns for the other values of a above are: - - y (hex) (binary) - - 7 249249 001001001001001001001001 << regular >> - 9 1c71c7 000111000111000111000111 << regular >> - 11 1745d 000000010111010001011101 << irregular >> - 13 13b13b 000100111011000100111011 << irregular >> - - The bit patterns for (a) corresponding to (y) of 11 and 13 may be - too irregular to warrant using this method. - - When z is a power of 2 minus 1, then the division by z is slightly - more complicated, involving an iterative solution. - - The code presented here solves division by 1 through 17, except for - 11 and 13. There are algorithms for both signed and unsigned - quantities given. - - TIMINGS (cycles) - - divisor positive negative unsigned - - . 1 2 2 2 - . 2 4 4 2 - . 3 19 21 19 - . 4 4 4 2 - . 5 18 22 19 - . 6 19 22 19 - . 8 4 4 2 - . 10 18 19 17 - . 12 18 20 18 - . 15 16 18 16 - . 16 4 4 2 - . 17 16 18 16 - - Now, the algorithm for 7, 9, and 14 is an iterative one. That is, - a loop body is executed until the tentative quotient is 0. The - number of times the loop body is executed varies depending on the - dividend, but is never more than two times. If the dividend is - less than the divisor, then the loop body is not executed at all. - Each iteration adds 4 cycles to the timings. - - divisor positive negative unsigned - - . 7 19+4n 20+4n 20+4n n = number of iterations - . 9 21+4n 22+4n 21+4n - . 14 21+4n 22+4n 20+4n - - To give an idea of how the number of iterations varies, here is a - table of dividend versus number of iterations when dividing by 7. - - smallest largest required - dividend dividend iterations - - . 0 6 0 - . 7 0x6ffffff 1 - 0x1000006 0xffffffff 2 - - There is some overlap in the range of numbers requiring 1 and 2 - iterations. */ - -RDEFINE(t2,r1) -RDEFINE(x2,arg0) /* r26 */ -RDEFINE(t1,arg1) /* r25 */ -RDEFINE(x1,ret1) /* r29 */ - - SUBSPA_MILLI_DIV - ATTR_MILLI - - .proc - .callinfo millicode - .entry -/* NONE of these routines require a stack frame - ALL of these routines are unwindable from millicode */ - -GSYM($$divide_by_constant) - .export $$divide_by_constant,millicode -/* Provides a "nice" label for the code covered by the unwind descriptor - for things like gprof. */ - -/* DIVISION BY 2 (shift by 1) */ -GSYM($$divI_2) - .export $$divI_2,millicode - comclr,>= arg0,0,0 - addi 1,arg0,arg0 - MILLIRET - extrs arg0,30,31,ret1 - - -/* DIVISION BY 4 (shift by 2) */ -GSYM($$divI_4) - .export $$divI_4,millicode - comclr,>= arg0,0,0 - addi 3,arg0,arg0 - MILLIRET - extrs arg0,29,30,ret1 - - -/* DIVISION BY 8 (shift by 3) */ -GSYM($$divI_8) - .export $$divI_8,millicode - comclr,>= arg0,0,0 - addi 7,arg0,arg0 - MILLIRET - extrs arg0,28,29,ret1 - -/* DIVISION BY 16 (shift by 4) */ -GSYM($$divI_16) - .export $$divI_16,millicode - comclr,>= arg0,0,0 - addi 15,arg0,arg0 - MILLIRET - extrs arg0,27,28,ret1 - -/**************************************************************************** -* -* DIVISION BY DIVISORS OF FFFFFFFF, and powers of 2 times these -* -* includes 3,5,15,17 and also 6,10,12 -* -****************************************************************************/ - -/* DIVISION BY 3 (use z = 2**32; a = 55555555) */ - -GSYM($$divI_3) - .export $$divI_3,millicode - comb,<,N x2,0,LREF(neg3) - - addi 1,x2,x2 /* this cannot overflow */ - extru x2,1,2,x1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(pos) - addc x1,0,x1 - -LSYM(neg3) - subi 1,x2,x2 /* this cannot overflow */ - extru x2,1,2,x1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(neg) - addc x1,0,x1 - -GSYM($$divU_3) - .export $$divU_3,millicode - addi 1,x2,x2 /* this CAN overflow */ - addc 0,0,x1 - shd x1,x2,30,t1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(pos) - addc x1,t1,x1 - -/* DIVISION BY 5 (use z = 2**32; a = 33333333) */ - -GSYM($$divI_5) - .export $$divI_5,millicode - comb,<,N x2,0,LREF(neg5) - - addi 3,x2,t1 /* this cannot overflow */ - sh1add x2,t1,x2 /* multiply by 3 to get started */ - b LREF(pos) - addc 0,0,x1 - -LSYM(neg5) - sub 0,x2,x2 /* negate x2 */ - addi 1,x2,x2 /* this cannot overflow */ - shd 0,x2,31,x1 /* get top bit (can be 1) */ - sh1add x2,x2,x2 /* multiply by 3 to get started */ - b LREF(neg) - addc x1,0,x1 - -GSYM($$divU_5) - .export $$divU_5,millicode - addi 1,x2,x2 /* this CAN overflow */ - addc 0,0,x1 - shd x1,x2,31,t1 /* multiply by 3 to get started */ - sh1add x2,x2,x2 - b LREF(pos) - addc t1,x1,x1 - -/* DIVISION BY 6 (shift to divide by 2 then divide by 3) */ -GSYM($$divI_6) - .export $$divI_6,millicode - comb,<,N x2,0,LREF(neg6) - extru x2,30,31,x2 /* divide by 2 */ - addi 5,x2,t1 /* compute 5*(x2+1) = 5*x2+5 */ - sh2add x2,t1,x2 /* multiply by 5 to get started */ - b LREF(pos) - addc 0,0,x1 - -LSYM(neg6) - subi 2,x2,x2 /* negate, divide by 2, and add 1 */ - /* negation and adding 1 are done */ - /* at the same time by the SUBI */ - extru x2,30,31,x2 - shd 0,x2,30,x1 - sh2add x2,x2,x2 /* multiply by 5 to get started */ - b LREF(neg) - addc x1,0,x1 - -GSYM($$divU_6) - .export $$divU_6,millicode - extru x2,30,31,x2 /* divide by 2 */ - addi 1,x2,x2 /* cannot carry */ - shd 0,x2,30,x1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(pos) - addc x1,0,x1 - -/* DIVISION BY 10 (shift to divide by 2 then divide by 5) */ -GSYM($$divU_10) - .export $$divU_10,millicode - extru x2,30,31,x2 /* divide by 2 */ - addi 3,x2,t1 /* compute 3*(x2+1) = (3*x2)+3 */ - sh1add x2,t1,x2 /* multiply by 3 to get started */ - addc 0,0,x1 -LSYM(pos) - shd x1,x2,28,t1 /* multiply by 0x11 */ - shd x2,0,28,t2 - add x2,t2,x2 - addc x1,t1,x1 -LSYM(pos_for_17) - shd x1,x2,24,t1 /* multiply by 0x101 */ - shd x2,0,24,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,16,t1 /* multiply by 0x10001 */ - shd x2,0,16,t2 - add x2,t2,x2 - MILLIRET - addc x1,t1,x1 - -GSYM($$divI_10) - .export $$divI_10,millicode - comb,< x2,0,LREF(neg10) - copy 0,x1 - extru x2,30,31,x2 /* divide by 2 */ - addib,TR 1,x2,LREF(pos) /* add 1 (cannot overflow) */ - sh1add x2,x2,x2 /* multiply by 3 to get started */ - -LSYM(neg10) - subi 2,x2,x2 /* negate, divide by 2, and add 1 */ - /* negation and adding 1 are done */ - /* at the same time by the SUBI */ - extru x2,30,31,x2 - sh1add x2,x2,x2 /* multiply by 3 to get started */ -LSYM(neg) - shd x1,x2,28,t1 /* multiply by 0x11 */ - shd x2,0,28,t2 - add x2,t2,x2 - addc x1,t1,x1 -LSYM(neg_for_17) - shd x1,x2,24,t1 /* multiply by 0x101 */ - shd x2,0,24,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,16,t1 /* multiply by 0x10001 */ - shd x2,0,16,t2 - add x2,t2,x2 - addc x1,t1,x1 - MILLIRET - sub 0,x1,x1 - -/* DIVISION BY 12 (shift to divide by 4 then divide by 3) */ -GSYM($$divI_12) - .export $$divI_12,millicode - comb,< x2,0,LREF(neg12) - copy 0,x1 - extru x2,29,30,x2 /* divide by 4 */ - addib,tr 1,x2,LREF(pos) /* compute 5*(x2+1) = 5*x2+5 */ - sh2add x2,x2,x2 /* multiply by 5 to get started */ - -LSYM(neg12) - subi 4,x2,x2 /* negate, divide by 4, and add 1 */ - /* negation and adding 1 are done */ - /* at the same time by the SUBI */ - extru x2,29,30,x2 - b LREF(neg) - sh2add x2,x2,x2 /* multiply by 5 to get started */ - -GSYM($$divU_12) - .export $$divU_12,millicode - extru x2,29,30,x2 /* divide by 4 */ - addi 5,x2,t1 /* cannot carry */ - sh2add x2,t1,x2 /* multiply by 5 to get started */ - b LREF(pos) - addc 0,0,x1 - -/* DIVISION BY 15 (use z = 2**32; a = 11111111) */ -GSYM($$divI_15) - .export $$divI_15,millicode - comb,< x2,0,LREF(neg15) - copy 0,x1 - addib,tr 1,x2,LREF(pos)+4 - shd x1,x2,28,t1 - -LSYM(neg15) - b LREF(neg) - subi 1,x2,x2 - -GSYM($$divU_15) - .export $$divU_15,millicode - addi 1,x2,x2 /* this CAN overflow */ - b LREF(pos) - addc 0,0,x1 - -/* DIVISION BY 17 (use z = 2**32; a = f0f0f0f) */ -GSYM($$divI_17) - .export $$divI_17,millicode - comb,<,n x2,0,LREF(neg17) - addi 1,x2,x2 /* this cannot overflow */ - shd 0,x2,28,t1 /* multiply by 0xf to get started */ - shd x2,0,28,t2 - sub t2,x2,x2 - b LREF(pos_for_17) - subb t1,0,x1 - -LSYM(neg17) - subi 1,x2,x2 /* this cannot overflow */ - shd 0,x2,28,t1 /* multiply by 0xf to get started */ - shd x2,0,28,t2 - sub t2,x2,x2 - b LREF(neg_for_17) - subb t1,0,x1 - -GSYM($$divU_17) - .export $$divU_17,millicode - addi 1,x2,x2 /* this CAN overflow */ - addc 0,0,x1 - shd x1,x2,28,t1 /* multiply by 0xf to get started */ -LSYM(u17) - shd x2,0,28,t2 - sub t2,x2,x2 - b LREF(pos_for_17) - subb t1,x1,x1 - - -/* DIVISION BY DIVISORS OF FFFFFF, and powers of 2 times these - includes 7,9 and also 14 - - - z = 2**24-1 - r = z mod x = 0 - - so choose b = 0 - - Also, in order to divide by z = 2**24-1, we approximate by dividing - by (z+1) = 2**24 (which is easy), and then correcting. - - (ax) = (z+1)q' + r - . = zq' + (q'+r) - - So to compute (ax)/z, compute q' = (ax)/(z+1) and r = (ax) mod (z+1) - Then the true remainder of (ax)/z is (q'+r). Repeat the process - with this new remainder, adding the tentative quotients together, - until a tentative quotient is 0 (and then we are done). There is - one last correction to be done. It is possible that (q'+r) = z. - If so, then (q'+r)/(z+1) = 0 and it looks like we are done. But, - in fact, we need to add 1 more to the quotient. Now, it turns - out that this happens if and only if the original value x is - an exact multiple of y. So, to avoid a three instruction test at - the end, instead use 1 instruction to add 1 to x at the beginning. */ - -/* DIVISION BY 7 (use z = 2**24-1; a = 249249) */ -GSYM($$divI_7) - .export $$divI_7,millicode - comb,<,n x2,0,LREF(neg7) -LSYM(7) - addi 1,x2,x2 /* cannot overflow */ - shd 0,x2,29,x1 - sh3add x2,x2,x2 - addc x1,0,x1 -LSYM(pos7) - shd x1,x2,26,t1 - shd x2,0,26,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,20,t1 - shd x2,0,20,t2 - add x2,t2,x2 - addc x1,t1,t1 - - /* computed <t1,x2>. Now divide it by (2**24 - 1) */ - - copy 0,x1 - shd,= t1,x2,24,t1 /* tentative quotient */ -LSYM(1) - addb,tr t1,x1,LREF(2) /* add to previous quotient */ - extru x2,31,24,x2 /* new remainder (unadjusted) */ - - MILLIRETN - -LSYM(2) - addb,tr t1,x2,LREF(1) /* adjust remainder */ - extru,= x2,7,8,t1 /* new quotient */ - -LSYM(neg7) - subi 1,x2,x2 /* negate x2 and add 1 */ -LSYM(8) - shd 0,x2,29,x1 - sh3add x2,x2,x2 - addc x1,0,x1 - -LSYM(neg7_shift) - shd x1,x2,26,t1 - shd x2,0,26,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,20,t1 - shd x2,0,20,t2 - add x2,t2,x2 - addc x1,t1,t1 - - /* computed <t1,x2>. Now divide it by (2**24 - 1) */ - - copy 0,x1 - shd,= t1,x2,24,t1 /* tentative quotient */ -LSYM(3) - addb,tr t1,x1,LREF(4) /* add to previous quotient */ - extru x2,31,24,x2 /* new remainder (unadjusted) */ - - MILLIRET - sub 0,x1,x1 /* negate result */ - -LSYM(4) - addb,tr t1,x2,LREF(3) /* adjust remainder */ - extru,= x2,7,8,t1 /* new quotient */ - -GSYM($$divU_7) - .export $$divU_7,millicode - addi 1,x2,x2 /* can carry */ - addc 0,0,x1 - shd x1,x2,29,t1 - sh3add x2,x2,x2 - b LREF(pos7) - addc t1,x1,x1 - -/* DIVISION BY 9 (use z = 2**24-1; a = 1c71c7) */ -GSYM($$divI_9) - .export $$divI_9,millicode - comb,<,n x2,0,LREF(neg9) - addi 1,x2,x2 /* cannot overflow */ - shd 0,x2,29,t1 - shd x2,0,29,t2 - sub t2,x2,x2 - b LREF(pos7) - subb t1,0,x1 - -LSYM(neg9) - subi 1,x2,x2 /* negate and add 1 */ - shd 0,x2,29,t1 - shd x2,0,29,t2 - sub t2,x2,x2 - b LREF(neg7_shift) - subb t1,0,x1 - -GSYM($$divU_9) - .export $$divU_9,millicode - addi 1,x2,x2 /* can carry */ - addc 0,0,x1 - shd x1,x2,29,t1 - shd x2,0,29,t2 - sub t2,x2,x2 - b LREF(pos7) - subb t1,x1,x1 - -/* DIVISION BY 14 (shift to divide by 2 then divide by 7) */ -GSYM($$divI_14) - .export $$divI_14,millicode - comb,<,n x2,0,LREF(neg14) -GSYM($$divU_14) - .export $$divU_14,millicode - b LREF(7) /* go to 7 case */ - extru x2,30,31,x2 /* divide by 2 */ - -LSYM(neg14) - subi 2,x2,x2 /* negate (and add 2) */ - b LREF(8) - extru x2,30,31,x2 /* divide by 2 */ - .exit - .procend - .end -#endif diff --git a/arch/parisc/lib/milli/dyncall.S b/arch/parisc/lib/milli/dyncall.S deleted file mode 100644 index 27f9ca558d0a..000000000000 --- a/arch/parisc/lib/milli/dyncall.S +++ /dev/null @@ -1,32 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#include "milli.h" - -#ifdef L_dyncall - SUBSPA_MILLI - ATTR_DATA -GSYM($$dyncall) - .export $$dyncall,millicode - .proc - .callinfo millicode - .entry - bb,>=,n %r22,30,LREF(1) ; branch if not plabel address - depi 0,31,2,%r22 ; clear the two least significant bits - ldw 4(%r22),%r19 ; load new LTP value - ldw 0(%r22),%r22 ; load address of target -LSYM(1) - bv %r0(%r22) ; branch to the real target - stw %r2,-24(%r30) ; save return address into frame marker - .exit - .procend -#endif diff --git a/arch/parisc/lib/milli/milli.S b/arch/parisc/lib/milli/milli.S deleted file mode 100644 index 47c6cde712e3..000000000000 --- a/arch/parisc/lib/milli/milli.S +++ /dev/null @@ -1,2071 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#ifdef CONFIG_64BIT - .level 2.0w -#endif - -/* Hardware General Registers. */ -r0: .reg %r0 -r1: .reg %r1 -r2: .reg %r2 -r3: .reg %r3 -r4: .reg %r4 -r5: .reg %r5 -r6: .reg %r6 -r7: .reg %r7 -r8: .reg %r8 -r9: .reg %r9 -r10: .reg %r10 -r11: .reg %r11 -r12: .reg %r12 -r13: .reg %r13 -r14: .reg %r14 -r15: .reg %r15 -r16: .reg %r16 -r17: .reg %r17 -r18: .reg %r18 -r19: .reg %r19 -r20: .reg %r20 -r21: .reg %r21 -r22: .reg %r22 -r23: .reg %r23 -r24: .reg %r24 -r25: .reg %r25 -r26: .reg %r26 -r27: .reg %r27 -r28: .reg %r28 -r29: .reg %r29 -r30: .reg %r30 -r31: .reg %r31 - -/* Hardware Space Registers. */ -sr0: .reg %sr0 -sr1: .reg %sr1 -sr2: .reg %sr2 -sr3: .reg %sr3 -sr4: .reg %sr4 -sr5: .reg %sr5 -sr6: .reg %sr6 -sr7: .reg %sr7 - -/* Hardware Floating Point Registers. */ -fr0: .reg %fr0 -fr1: .reg %fr1 -fr2: .reg %fr2 -fr3: .reg %fr3 -fr4: .reg %fr4 -fr5: .reg %fr5 -fr6: .reg %fr6 -fr7: .reg %fr7 -fr8: .reg %fr8 -fr9: .reg %fr9 -fr10: .reg %fr10 -fr11: .reg %fr11 -fr12: .reg %fr12 -fr13: .reg %fr13 -fr14: .reg %fr14 -fr15: .reg %fr15 - -/* Hardware Control Registers. */ -cr11: .reg %cr11 -sar: .reg %cr11 /* Shift Amount Register */ - -/* Software Architecture General Registers. */ -rp: .reg r2 /* return pointer */ -#ifdef CONFIG_64BIT -mrp: .reg r2 /* millicode return pointer */ -#else -mrp: .reg r31 /* millicode return pointer */ -#endif -ret0: .reg r28 /* return value */ -ret1: .reg r29 /* return value (high part of double) */ -sp: .reg r30 /* stack pointer */ -dp: .reg r27 /* data pointer */ -arg0: .reg r26 /* argument */ -arg1: .reg r25 /* argument or high part of double argument */ -arg2: .reg r24 /* argument */ -arg3: .reg r23 /* argument or high part of double argument */ - -/* Software Architecture Space Registers. */ -/* sr0 ; return link from BLE */ -sret: .reg sr1 /* return value */ -sarg: .reg sr1 /* argument */ -/* sr4 ; PC SPACE tracker */ -/* sr5 ; process private data */ - -/* Frame Offsets (millicode convention!) Used when calling other - millicode routines. Stack unwinding is dependent upon these - definitions. */ -r31_slot: .equ -20 /* "current RP" slot */ -sr0_slot: .equ -16 /* "static link" slot */ -#if defined(CONFIG_64BIT) -mrp_slot: .equ -16 /* "current RP" slot */ -psp_slot: .equ -8 /* "previous SP" slot */ -#else -mrp_slot: .equ -20 /* "current RP" slot (replacing "r31_slot") */ -#endif - - -#define DEFINE(name,value)name: .EQU value -#define RDEFINE(name,value)name: .REG value -#ifdef milliext -#define MILLI_BE(lbl) BE lbl(sr7,r0) -#define MILLI_BEN(lbl) BE,n lbl(sr7,r0) -#define MILLI_BLE(lbl) BLE lbl(sr7,r0) -#define MILLI_BLEN(lbl) BLE,n lbl(sr7,r0) -#define MILLIRETN BE,n 0(sr0,mrp) -#define MILLIRET BE 0(sr0,mrp) -#define MILLI_RETN BE,n 0(sr0,mrp) -#define MILLI_RET BE 0(sr0,mrp) -#else -#define MILLI_BE(lbl) B lbl -#define MILLI_BEN(lbl) B,n lbl -#define MILLI_BLE(lbl) BL lbl,mrp -#define MILLI_BLEN(lbl) BL,n lbl,mrp -#define MILLIRETN BV,n 0(mrp) -#define MILLIRET BV 0(mrp) -#define MILLI_RETN BV,n 0(mrp) -#define MILLI_RET BV 0(mrp) -#endif - -#define CAT(a,b) a##b - -#define SUBSPA_MILLI .section .text -#define SUBSPA_MILLI_DIV .section .text.div,"ax",@progbits! .align 16 -#define SUBSPA_MILLI_MUL .section .text.mul,"ax",@progbits! .align 16 -#define ATTR_MILLI -#define SUBSPA_DATA .section .data -#define ATTR_DATA -#define GLOBAL $global$ -#define GSYM(sym) !sym: -#define LSYM(sym) !CAT(.L,sym:) -#define LREF(sym) CAT(.L,sym) - -#ifdef L_dyncall - SUBSPA_MILLI - ATTR_DATA -GSYM($$dyncall) - .export $$dyncall,millicode - .proc - .callinfo millicode - .entry - bb,>=,n %r22,30,LREF(1) ; branch if not plabel address - depi 0,31,2,%r22 ; clear the two least significant bits - ldw 4(%r22),%r19 ; load new LTP value - ldw 0(%r22),%r22 ; load address of target -LSYM(1) - bv %r0(%r22) ; branch to the real target - stw %r2,-24(%r30) ; save return address into frame marker - .exit - .procend -#endif - -#ifdef L_divI -/* ROUTINES: $$divI, $$divoI - - Single precision divide for signed binary integers. - - The quotient is truncated towards zero. - The sign of the quotient is the XOR of the signs of the dividend and - divisor. - Divide by zero is trapped. - Divide of -2**31 by -1 is trapped for $$divoI but not for $$divI. - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = quotient - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: - . divisor is zero (traps with ADDIT,= 0,25,0) - . dividend==-2**31 and divisor==-1 and routine is $$divoI - . (traps with ADDO 26,25,0) - . Changes memory at the following places: - . NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Branchs to other millicode routines using BE - . $$div_# for # being 2,3,4,5,6,7,8,9,10,12,14,15 - . - . For selected divisors, calls a divide by constant routine written by - . Karl Pettis. Eligible divisors are 1..15 excluding 11 and 13. - . - . The only overflow case is -2**31 divided by -1. - . Both routines return -2**31 but only $$divoI traps. */ - -RDEFINE(temp,r1) -RDEFINE(retreg,ret1) /* r29 */ -RDEFINE(temp1,arg0) - SUBSPA_MILLI_DIV - ATTR_MILLI - .import $$divI_2,millicode - .import $$divI_3,millicode - .import $$divI_4,millicode - .import $$divI_5,millicode - .import $$divI_6,millicode - .import $$divI_7,millicode - .import $$divI_8,millicode - .import $$divI_9,millicode - .import $$divI_10,millicode - .import $$divI_12,millicode - .import $$divI_14,millicode - .import $$divI_15,millicode - .export $$divI,millicode - .export $$divoI,millicode - .proc - .callinfo millicode - .entry -GSYM($$divoI) - comib,=,n -1,arg1,LREF(negative1) /* when divisor == -1 */ -GSYM($$divI) - ldo -1(arg1),temp /* is there at most one bit set ? */ - and,<> arg1,temp,r0 /* if not, don't use power of 2 divide */ - addi,> 0,arg1,r0 /* if divisor > 0, use power of 2 divide */ - b,n LREF(neg_denom) -LSYM(pow2) - addi,>= 0,arg0,retreg /* if numerator is negative, add the */ - add arg0,temp,retreg /* (denominaotr -1) to correct for shifts */ - extru,= arg1,15,16,temp /* test denominator with 0xffff0000 */ - extrs retreg,15,16,retreg /* retreg = retreg >> 16 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 16) */ - ldi 0xcc,temp1 /* setup 0xcc in temp1 */ - extru,= arg1,23,8,temp /* test denominator with 0xff00 */ - extrs retreg,23,24,retreg /* retreg = retreg >> 8 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 8) */ - ldi 0xaa,temp /* setup 0xaa in temp */ - extru,= arg1,27,4,r0 /* test denominator with 0xf0 */ - extrs retreg,27,28,retreg /* retreg = retreg >> 4 */ - and,= arg1,temp1,r0 /* test denominator with 0xcc */ - extrs retreg,29,30,retreg /* retreg = retreg >> 2 */ - and,= arg1,temp,r0 /* test denominator with 0xaa */ - extrs retreg,30,31,retreg /* retreg = retreg >> 1 */ - MILLIRETN -LSYM(neg_denom) - addi,< 0,arg1,r0 /* if arg1 >= 0, it's not power of 2 */ - b,n LREF(regular_seq) - sub r0,arg1,temp /* make denominator positive */ - comb,=,n arg1,temp,LREF(regular_seq) /* test against 0x80000000 and 0 */ - ldo -1(temp),retreg /* is there at most one bit set ? */ - and,= temp,retreg,r0 /* if so, the denominator is power of 2 */ - b,n LREF(regular_seq) - sub r0,arg0,retreg /* negate numerator */ - comb,=,n arg0,retreg,LREF(regular_seq) /* test against 0x80000000 */ - copy retreg,arg0 /* set up arg0, arg1 and temp */ - copy temp,arg1 /* before branching to pow2 */ - b LREF(pow2) - ldo -1(arg1),temp -LSYM(regular_seq) - comib,>>=,n 15,arg1,LREF(small_divisor) - add,>= 0,arg0,retreg /* move dividend, if retreg < 0, */ -LSYM(normal) - subi 0,retreg,retreg /* make it positive */ - sub 0,arg1,temp /* clear carry, */ - /* negate the divisor */ - ds 0,temp,0 /* set V-bit to the comple- */ - /* ment of the divisor sign */ - add retreg,retreg,retreg /* shift msb bit into carry */ - ds r0,arg1,temp /* 1st divide step, if no carry */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 2nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 3rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 4th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 5th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 6th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 7th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 8th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 9th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 10th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 11th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 12th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 13th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 14th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 15th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 16th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 17th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 18th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 19th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 20th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 21st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 22nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 23rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 24th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 25th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 26th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 27th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 28th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 29th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 30th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 31st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 32nd divide step, */ - addc retreg,retreg,retreg /* shift last retreg bit into retreg */ - xor,>= arg0,arg1,0 /* get correct sign of quotient */ - sub 0,retreg,retreg /* based on operand signs */ - MILLIRETN - nop - -LSYM(small_divisor) - -#if defined(CONFIG_64BIT) -/* Clear the upper 32 bits of the arg1 register. We are working with */ -/* small divisors (and 32-bit integers) We must not be mislead */ -/* by "1" bits left in the upper 32 bits. */ - depd %r0,31,32,%r25 -#endif - blr,n arg1,r0 - nop -/* table for divisor == 0,1, ... ,15 */ - addit,= 0,arg1,r0 /* trap if divisor == 0 */ - nop - MILLIRET /* divisor == 1 */ - copy arg0,retreg - MILLI_BEN($$divI_2) /* divisor == 2 */ - nop - MILLI_BEN($$divI_3) /* divisor == 3 */ - nop - MILLI_BEN($$divI_4) /* divisor == 4 */ - nop - MILLI_BEN($$divI_5) /* divisor == 5 */ - nop - MILLI_BEN($$divI_6) /* divisor == 6 */ - nop - MILLI_BEN($$divI_7) /* divisor == 7 */ - nop - MILLI_BEN($$divI_8) /* divisor == 8 */ - nop - MILLI_BEN($$divI_9) /* divisor == 9 */ - nop - MILLI_BEN($$divI_10) /* divisor == 10 */ - nop - b LREF(normal) /* divisor == 11 */ - add,>= 0,arg0,retreg - MILLI_BEN($$divI_12) /* divisor == 12 */ - nop - b LREF(normal) /* divisor == 13 */ - add,>= 0,arg0,retreg - MILLI_BEN($$divI_14) /* divisor == 14 */ - nop - MILLI_BEN($$divI_15) /* divisor == 15 */ - nop - -LSYM(negative1) - sub 0,arg0,retreg /* result is negation of dividend */ - MILLIRET - addo arg0,arg1,r0 /* trap iff dividend==0x80000000 && divisor==-1 */ - .exit - .procend - .end -#endif - -#ifdef L_divU -/* ROUTINE: $$divU - . - . Single precision divide for unsigned integers. - . - . Quotient is truncated towards zero. - . Traps on divide by zero. - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = quotient - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: - . divisor is zero - . Changes memory at the following places: - . NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Does not create a stack frame. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Branchs to other millicode routines using BE: - . $$divU_# for 3,5,6,7,9,10,12,14,15 - . - . For selected small divisors calls the special divide by constant - . routines written by Karl Pettis. These are: 3,5,6,7,9,10,12,14,15. */ - -RDEFINE(temp,r1) -RDEFINE(retreg,ret1) /* r29 */ -RDEFINE(temp1,arg0) - SUBSPA_MILLI_DIV - ATTR_MILLI - .export $$divU,millicode - .import $$divU_3,millicode - .import $$divU_5,millicode - .import $$divU_6,millicode - .import $$divU_7,millicode - .import $$divU_9,millicode - .import $$divU_10,millicode - .import $$divU_12,millicode - .import $$divU_14,millicode - .import $$divU_15,millicode - .proc - .callinfo millicode - .entry -GSYM($$divU) -/* The subtract is not nullified since it does no harm and can be used - by the two cases that branch back to "normal". */ - ldo -1(arg1),temp /* is there at most one bit set ? */ - and,= arg1,temp,r0 /* if so, denominator is power of 2 */ - b LREF(regular_seq) - addit,= 0,arg1,0 /* trap for zero dvr */ - copy arg0,retreg - extru,= arg1,15,16,temp /* test denominator with 0xffff0000 */ - extru retreg,15,16,retreg /* retreg = retreg >> 16 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 16) */ - ldi 0xcc,temp1 /* setup 0xcc in temp1 */ - extru,= arg1,23,8,temp /* test denominator with 0xff00 */ - extru retreg,23,24,retreg /* retreg = retreg >> 8 */ - or arg1,temp,arg1 /* arg1 = arg1 | (arg1 >> 8) */ - ldi 0xaa,temp /* setup 0xaa in temp */ - extru,= arg1,27,4,r0 /* test denominator with 0xf0 */ - extru retreg,27,28,retreg /* retreg = retreg >> 4 */ - and,= arg1,temp1,r0 /* test denominator with 0xcc */ - extru retreg,29,30,retreg /* retreg = retreg >> 2 */ - and,= arg1,temp,r0 /* test denominator with 0xaa */ - extru retreg,30,31,retreg /* retreg = retreg >> 1 */ - MILLIRETN - nop -LSYM(regular_seq) - comib,>= 15,arg1,LREF(special_divisor) - subi 0,arg1,temp /* clear carry, negate the divisor */ - ds r0,temp,r0 /* set V-bit to 1 */ -LSYM(normal) - add arg0,arg0,retreg /* shift msb bit into carry */ - ds r0,arg1,temp /* 1st divide step, if no carry */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 2nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 3rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 4th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 5th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 6th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 7th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 8th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 9th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 10th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 11th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 12th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 13th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 14th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 15th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 16th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 17th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 18th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 19th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 20th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 21st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 22nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 23rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 24th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 25th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 26th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 27th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 28th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 29th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 30th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 31st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds temp,arg1,temp /* 32nd divide step, */ - MILLIRET - addc retreg,retreg,retreg /* shift last retreg bit into retreg */ - -/* Handle the cases where divisor is a small constant or has high bit on. */ -LSYM(special_divisor) -/* blr arg1,r0 */ -/* comib,>,n 0,arg1,LREF(big_divisor) ; nullify previous instruction */ - -/* Pratap 8/13/90. The 815 Stirling chip set has a bug that prevents us from - generating such a blr, comib sequence. A problem in nullification. So I - rewrote this code. */ - -#if defined(CONFIG_64BIT) -/* Clear the upper 32 bits of the arg1 register. We are working with - small divisors (and 32-bit unsigned integers) We must not be mislead - by "1" bits left in the upper 32 bits. */ - depd %r0,31,32,%r25 -#endif - comib,> 0,arg1,LREF(big_divisor) - nop - blr arg1,r0 - nop - -LSYM(zero_divisor) /* this label is here to provide external visibility */ - addit,= 0,arg1,0 /* trap for zero dvr */ - nop - MILLIRET /* divisor == 1 */ - copy arg0,retreg - MILLIRET /* divisor == 2 */ - extru arg0,30,31,retreg - MILLI_BEN($$divU_3) /* divisor == 3 */ - nop - MILLIRET /* divisor == 4 */ - extru arg0,29,30,retreg - MILLI_BEN($$divU_5) /* divisor == 5 */ - nop - MILLI_BEN($$divU_6) /* divisor == 6 */ - nop - MILLI_BEN($$divU_7) /* divisor == 7 */ - nop - MILLIRET /* divisor == 8 */ - extru arg0,28,29,retreg - MILLI_BEN($$divU_9) /* divisor == 9 */ - nop - MILLI_BEN($$divU_10) /* divisor == 10 */ - nop - b LREF(normal) /* divisor == 11 */ - ds r0,temp,r0 /* set V-bit to 1 */ - MILLI_BEN($$divU_12) /* divisor == 12 */ - nop - b LREF(normal) /* divisor == 13 */ - ds r0,temp,r0 /* set V-bit to 1 */ - MILLI_BEN($$divU_14) /* divisor == 14 */ - nop - MILLI_BEN($$divU_15) /* divisor == 15 */ - nop - -/* Handle the case where the high bit is on in the divisor. - Compute: if( dividend>=divisor) quotient=1; else quotient=0; - Note: dividend>==divisor iff dividend-divisor does not borrow - and not borrow iff carry. */ -LSYM(big_divisor) - sub arg0,arg1,r0 - MILLIRET - addc r0,r0,retreg - .exit - .procend - .end -#endif - -#ifdef L_remI -/* ROUTINE: $$remI - - DESCRIPTION: - . $$remI returns the remainder of the division of two signed 32-bit - . integers. The sign of the remainder is the same as the sign of - . the dividend. - - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = destroyed - . arg1 = destroyed - . ret1 = remainder - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: DIVIDE BY ZERO - . Changes memory at the following places: NONE - - PERMISSIBLE CONTEXT: - . Unwindable - . Does not create a stack frame - . Is usable for internal or external microcode - - DISCUSSION: - . Calls other millicode routines via mrp: NONE - . Calls other millicode routines: NONE */ - -RDEFINE(tmp,r1) -RDEFINE(retreg,ret1) - - SUBSPA_MILLI - ATTR_MILLI - .proc - .callinfo millicode - .entry -GSYM($$remI) -GSYM($$remoI) - .export $$remI,MILLICODE - .export $$remoI,MILLICODE - ldo -1(arg1),tmp /* is there at most one bit set ? */ - and,<> arg1,tmp,r0 /* if not, don't use power of 2 */ - addi,> 0,arg1,r0 /* if denominator > 0, use power */ - /* of 2 */ - b,n LREF(neg_denom) -LSYM(pow2) - comb,>,n 0,arg0,LREF(neg_num) /* is numerator < 0 ? */ - and arg0,tmp,retreg /* get the result */ - MILLIRETN -LSYM(neg_num) - subi 0,arg0,arg0 /* negate numerator */ - and arg0,tmp,retreg /* get the result */ - subi 0,retreg,retreg /* negate result */ - MILLIRETN -LSYM(neg_denom) - addi,< 0,arg1,r0 /* if arg1 >= 0, it's not power */ - /* of 2 */ - b,n LREF(regular_seq) - sub r0,arg1,tmp /* make denominator positive */ - comb,=,n arg1,tmp,LREF(regular_seq) /* test against 0x80000000 and 0 */ - ldo -1(tmp),retreg /* is there at most one bit set ? */ - and,= tmp,retreg,r0 /* if not, go to regular_seq */ - b,n LREF(regular_seq) - comb,>,n 0,arg0,LREF(neg_num_2) /* if arg0 < 0, negate it */ - and arg0,retreg,retreg - MILLIRETN -LSYM(neg_num_2) - subi 0,arg0,tmp /* test against 0x80000000 */ - and tmp,retreg,retreg - subi 0,retreg,retreg - MILLIRETN -LSYM(regular_seq) - addit,= 0,arg1,0 /* trap if div by zero */ - add,>= 0,arg0,retreg /* move dividend, if retreg < 0, */ - sub 0,retreg,retreg /* make it positive */ - sub 0,arg1, tmp /* clear carry, */ - /* negate the divisor */ - ds 0, tmp,0 /* set V-bit to the comple- */ - /* ment of the divisor sign */ - or 0,0, tmp /* clear tmp */ - add retreg,retreg,retreg /* shift msb bit into carry */ - ds tmp,arg1, tmp /* 1st divide step, if no carry */ - /* out, msb of quotient = 0 */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ -LSYM(t1) - ds tmp,arg1, tmp /* 2nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 3rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 4th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 5th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 6th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 7th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 8th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 9th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 10th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 11th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 12th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 13th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 14th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 15th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 16th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 17th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 18th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 19th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 20th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 21st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 22nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 23rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 24th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 25th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 26th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 27th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 28th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 29th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 30th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 31st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 32nd divide step, */ - addc retreg,retreg,retreg /* shift last bit into retreg */ - movb,>=,n tmp,retreg,LREF(finish) /* branch if pos. tmp */ - add,< arg1,0,0 /* if arg1 > 0, add arg1 */ - add,tr tmp,arg1,retreg /* for correcting remainder tmp */ - sub tmp,arg1,retreg /* else add absolute value arg1 */ -LSYM(finish) - add,>= arg0,0,0 /* set sign of remainder */ - sub 0,retreg,retreg /* to sign of dividend */ - MILLIRET - nop - .exit - .procend -#ifdef milliext - .origin 0x00000200 -#endif - .end -#endif - -#ifdef L_remU -/* ROUTINE: $$remU - . Single precision divide for remainder with unsigned binary integers. - . - . The remainder must be dividend-(dividend/divisor)*divisor. - . Divide by zero is trapped. - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = remainder - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: DIVIDE BY ZERO - . Changes memory at the following places: NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Does not create a stack frame. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Calls other millicode routines using mrp: NONE - . Calls other millicode routines: NONE */ - - -RDEFINE(temp,r1) -RDEFINE(rmndr,ret1) /* r29 */ - SUBSPA_MILLI - ATTR_MILLI - .export $$remU,millicode - .proc - .callinfo millicode - .entry -GSYM($$remU) - ldo -1(arg1),temp /* is there at most one bit set ? */ - and,= arg1,temp,r0 /* if not, don't use power of 2 */ - b LREF(regular_seq) - addit,= 0,arg1,r0 /* trap on div by zero */ - and arg0,temp,rmndr /* get the result for power of 2 */ - MILLIRETN -LSYM(regular_seq) - comib,>=,n 0,arg1,LREF(special_case) - subi 0,arg1,rmndr /* clear carry, negate the divisor */ - ds r0,rmndr,r0 /* set V-bit to 1 */ - add arg0,arg0,temp /* shift msb bit into carry */ - ds r0,arg1,rmndr /* 1st divide step, if no carry */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 2nd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 3rd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 4th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 5th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 6th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 7th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 8th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 9th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 10th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 11th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 12th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 13th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 14th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 15th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 16th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 17th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 18th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 19th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 20th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 21st divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 22nd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 23rd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 24th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 25th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 26th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 27th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 28th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 29th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 30th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 31st divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 32nd divide step, */ - comiclr,<= 0,rmndr,r0 - add rmndr,arg1,rmndr /* correction */ - MILLIRETN - nop - -/* Putting >= on the last DS and deleting COMICLR does not work! */ -LSYM(special_case) - sub,>>= arg0,arg1,rmndr - copy arg0,rmndr - MILLIRETN - nop - .exit - .procend - .end -#endif - -#ifdef L_div_const -/* ROUTINE: $$divI_2 - . $$divI_3 $$divU_3 - . $$divI_4 - . $$divI_5 $$divU_5 - . $$divI_6 $$divU_6 - . $$divI_7 $$divU_7 - . $$divI_8 - . $$divI_9 $$divU_9 - . $$divI_10 $$divU_10 - . - . $$divI_12 $$divU_12 - . - . $$divI_14 $$divU_14 - . $$divI_15 $$divU_15 - . $$divI_16 - . $$divI_17 $$divU_17 - . - . Divide by selected constants for single precision binary integers. - - INPUT REGISTERS: - . arg0 == dividend - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = quotient - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: NONE - . Changes memory at the following places: NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Does not create a stack frame. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Calls other millicode routines using mrp: NONE - . Calls other millicode routines: NONE */ - - -/* TRUNCATED DIVISION BY SMALL INTEGERS - - We are interested in q(x) = floor(x/y), where x >= 0 and y > 0 - (with y fixed). - - Let a = floor(z/y), for some choice of z. Note that z will be - chosen so that division by z is cheap. - - Let r be the remainder(z/y). In other words, r = z - ay. - - Now, our method is to choose a value for b such that - - q'(x) = floor((ax+b)/z) - - is equal to q(x) over as large a range of x as possible. If the - two are equal over a sufficiently large range, and if it is easy to - form the product (ax), and it is easy to divide by z, then we can - perform the division much faster than the general division algorithm. - - So, we want the following to be true: - - . For x in the following range: - . - . ky <= x < (k+1)y - . - . implies that - . - . k <= (ax+b)/z < (k+1) - - We want to determine b such that this is true for all k in the - range {0..K} for some maximum K. - - Since (ax+b) is an increasing function of x, we can take each - bound separately to determine the "best" value for b. - - (ax+b)/z < (k+1) implies - - (a((k+1)y-1)+b < (k+1)z implies - - b < a + (k+1)(z-ay) implies - - b < a + (k+1)r - - This needs to be true for all k in the range {0..K}. In - particular, it is true for k = 0 and this leads to a maximum - acceptable value for b. - - b < a+r or b <= a+r-1 - - Taking the other bound, we have - - k <= (ax+b)/z implies - - k <= (aky+b)/z implies - - k(z-ay) <= b implies - - kr <= b - - Clearly, the largest range for k will be achieved by maximizing b, - when r is not zero. When r is zero, then the simplest choice for b - is 0. When r is not 0, set - - . b = a+r-1 - - Now, by construction, q'(x) = floor((ax+b)/z) = q(x) = floor(x/y) - for all x in the range: - - . 0 <= x < (K+1)y - - We need to determine what K is. Of our two bounds, - - . b < a+(k+1)r is satisfied for all k >= 0, by construction. - - The other bound is - - . kr <= b - - This is always true if r = 0. If r is not 0 (the usual case), then - K = floor((a+r-1)/r), is the maximum value for k. - - Therefore, the formula q'(x) = floor((ax+b)/z) yields the correct - answer for q(x) = floor(x/y) when x is in the range - - (0,(K+1)y-1) K = floor((a+r-1)/r) - - To be most useful, we want (K+1)y-1 = (max x) >= 2**32-1 so that - the formula for q'(x) yields the correct value of q(x) for all x - representable by a single word in HPPA. - - We are also constrained in that computing the product (ax), adding - b, and dividing by z must all be done quickly, otherwise we will be - better off going through the general algorithm using the DS - instruction, which uses approximately 70 cycles. - - For each y, there is a choice of z which satisfies the constraints - for (K+1)y >= 2**32. We may not, however, be able to satisfy the - timing constraints for arbitrary y. It seems that z being equal to - a power of 2 or a power of 2 minus 1 is as good as we can do, since - it minimizes the time to do division by z. We want the choice of z - to also result in a value for (a) that minimizes the computation of - the product (ax). This is best achieved if (a) has a regular bit - pattern (so the multiplication can be done with shifts and adds). - The value of (a) also needs to be less than 2**32 so the product is - always guaranteed to fit in 2 words. - - In actual practice, the following should be done: - - 1) For negative x, you should take the absolute value and remember - . the fact so that the result can be negated. This obviously does - . not apply in the unsigned case. - 2) For even y, you should factor out the power of 2 that divides y - . and divide x by it. You can then proceed by dividing by the - . odd factor of y. - - Here is a table of some odd values of y, and corresponding choices - for z which are "good". - - y z r a (hex) max x (hex) - - 3 2**32 1 55555555 100000001 - 5 2**32 1 33333333 100000003 - 7 2**24-1 0 249249 (infinite) - 9 2**24-1 0 1c71c7 (infinite) - 11 2**20-1 0 1745d (infinite) - 13 2**24-1 0 13b13b (infinite) - 15 2**32 1 11111111 10000000d - 17 2**32 1 f0f0f0f 10000000f - - If r is 1, then b = a+r-1 = a. This simplifies the computation - of (ax+b), since you can compute (x+1)(a) instead. If r is 0, - then b = 0 is ok to use which simplifies (ax+b). - - The bit patterns for 55555555, 33333333, and 11111111 are obviously - very regular. The bit patterns for the other values of a above are: - - y (hex) (binary) - - 7 249249 001001001001001001001001 << regular >> - 9 1c71c7 000111000111000111000111 << regular >> - 11 1745d 000000010111010001011101 << irregular >> - 13 13b13b 000100111011000100111011 << irregular >> - - The bit patterns for (a) corresponding to (y) of 11 and 13 may be - too irregular to warrant using this method. - - When z is a power of 2 minus 1, then the division by z is slightly - more complicated, involving an iterative solution. - - The code presented here solves division by 1 through 17, except for - 11 and 13. There are algorithms for both signed and unsigned - quantities given. - - TIMINGS (cycles) - - divisor positive negative unsigned - - . 1 2 2 2 - . 2 4 4 2 - . 3 19 21 19 - . 4 4 4 2 - . 5 18 22 19 - . 6 19 22 19 - . 8 4 4 2 - . 10 18 19 17 - . 12 18 20 18 - . 15 16 18 16 - . 16 4 4 2 - . 17 16 18 16 - - Now, the algorithm for 7, 9, and 14 is an iterative one. That is, - a loop body is executed until the tentative quotient is 0. The - number of times the loop body is executed varies depending on the - dividend, but is never more than two times. If the dividend is - less than the divisor, then the loop body is not executed at all. - Each iteration adds 4 cycles to the timings. - - divisor positive negative unsigned - - . 7 19+4n 20+4n 20+4n n = number of iterations - . 9 21+4n 22+4n 21+4n - . 14 21+4n 22+4n 20+4n - - To give an idea of how the number of iterations varies, here is a - table of dividend versus number of iterations when dividing by 7. - - smallest largest required - dividend dividend iterations - - . 0 6 0 - . 7 0x6ffffff 1 - 0x1000006 0xffffffff 2 - - There is some overlap in the range of numbers requiring 1 and 2 - iterations. */ - -RDEFINE(t2,r1) -RDEFINE(x2,arg0) /* r26 */ -RDEFINE(t1,arg1) /* r25 */ -RDEFINE(x1,ret1) /* r29 */ - - SUBSPA_MILLI_DIV - ATTR_MILLI - - .proc - .callinfo millicode - .entry -/* NONE of these routines require a stack frame - ALL of these routines are unwindable from millicode */ - -GSYM($$divide_by_constant) - .export $$divide_by_constant,millicode -/* Provides a "nice" label for the code covered by the unwind descriptor - for things like gprof. */ - -/* DIVISION BY 2 (shift by 1) */ -GSYM($$divI_2) - .export $$divI_2,millicode - comclr,>= arg0,0,0 - addi 1,arg0,arg0 - MILLIRET - extrs arg0,30,31,ret1 - - -/* DIVISION BY 4 (shift by 2) */ -GSYM($$divI_4) - .export $$divI_4,millicode - comclr,>= arg0,0,0 - addi 3,arg0,arg0 - MILLIRET - extrs arg0,29,30,ret1 - - -/* DIVISION BY 8 (shift by 3) */ -GSYM($$divI_8) - .export $$divI_8,millicode - comclr,>= arg0,0,0 - addi 7,arg0,arg0 - MILLIRET - extrs arg0,28,29,ret1 - -/* DIVISION BY 16 (shift by 4) */ -GSYM($$divI_16) - .export $$divI_16,millicode - comclr,>= arg0,0,0 - addi 15,arg0,arg0 - MILLIRET - extrs arg0,27,28,ret1 - -/**************************************************************************** -* -* DIVISION BY DIVISORS OF FFFFFFFF, and powers of 2 times these -* -* includes 3,5,15,17 and also 6,10,12 -* -****************************************************************************/ - -/* DIVISION BY 3 (use z = 2**32; a = 55555555) */ - -GSYM($$divI_3) - .export $$divI_3,millicode - comb,<,N x2,0,LREF(neg3) - - addi 1,x2,x2 /* this cannot overflow */ - extru x2,1,2,x1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(pos) - addc x1,0,x1 - -LSYM(neg3) - subi 1,x2,x2 /* this cannot overflow */ - extru x2,1,2,x1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(neg) - addc x1,0,x1 - -GSYM($$divU_3) - .export $$divU_3,millicode - addi 1,x2,x2 /* this CAN overflow */ - addc 0,0,x1 - shd x1,x2,30,t1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(pos) - addc x1,t1,x1 - -/* DIVISION BY 5 (use z = 2**32; a = 33333333) */ - -GSYM($$divI_5) - .export $$divI_5,millicode - comb,<,N x2,0,LREF(neg5) - - addi 3,x2,t1 /* this cannot overflow */ - sh1add x2,t1,x2 /* multiply by 3 to get started */ - b LREF(pos) - addc 0,0,x1 - -LSYM(neg5) - sub 0,x2,x2 /* negate x2 */ - addi 1,x2,x2 /* this cannot overflow */ - shd 0,x2,31,x1 /* get top bit (can be 1) */ - sh1add x2,x2,x2 /* multiply by 3 to get started */ - b LREF(neg) - addc x1,0,x1 - -GSYM($$divU_5) - .export $$divU_5,millicode - addi 1,x2,x2 /* this CAN overflow */ - addc 0,0,x1 - shd x1,x2,31,t1 /* multiply by 3 to get started */ - sh1add x2,x2,x2 - b LREF(pos) - addc t1,x1,x1 - -/* DIVISION BY 6 (shift to divide by 2 then divide by 3) */ -GSYM($$divI_6) - .export $$divI_6,millicode - comb,<,N x2,0,LREF(neg6) - extru x2,30,31,x2 /* divide by 2 */ - addi 5,x2,t1 /* compute 5*(x2+1) = 5*x2+5 */ - sh2add x2,t1,x2 /* multiply by 5 to get started */ - b LREF(pos) - addc 0,0,x1 - -LSYM(neg6) - subi 2,x2,x2 /* negate, divide by 2, and add 1 */ - /* negation and adding 1 are done */ - /* at the same time by the SUBI */ - extru x2,30,31,x2 - shd 0,x2,30,x1 - sh2add x2,x2,x2 /* multiply by 5 to get started */ - b LREF(neg) - addc x1,0,x1 - -GSYM($$divU_6) - .export $$divU_6,millicode - extru x2,30,31,x2 /* divide by 2 */ - addi 1,x2,x2 /* cannot carry */ - shd 0,x2,30,x1 /* multiply by 5 to get started */ - sh2add x2,x2,x2 - b LREF(pos) - addc x1,0,x1 - -/* DIVISION BY 10 (shift to divide by 2 then divide by 5) */ -GSYM($$divU_10) - .export $$divU_10,millicode - extru x2,30,31,x2 /* divide by 2 */ - addi 3,x2,t1 /* compute 3*(x2+1) = (3*x2)+3 */ - sh1add x2,t1,x2 /* multiply by 3 to get started */ - addc 0,0,x1 -LSYM(pos) - shd x1,x2,28,t1 /* multiply by 0x11 */ - shd x2,0,28,t2 - add x2,t2,x2 - addc x1,t1,x1 -LSYM(pos_for_17) - shd x1,x2,24,t1 /* multiply by 0x101 */ - shd x2,0,24,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,16,t1 /* multiply by 0x10001 */ - shd x2,0,16,t2 - add x2,t2,x2 - MILLIRET - addc x1,t1,x1 - -GSYM($$divI_10) - .export $$divI_10,millicode - comb,< x2,0,LREF(neg10) - copy 0,x1 - extru x2,30,31,x2 /* divide by 2 */ - addib,TR 1,x2,LREF(pos) /* add 1 (cannot overflow) */ - sh1add x2,x2,x2 /* multiply by 3 to get started */ - -LSYM(neg10) - subi 2,x2,x2 /* negate, divide by 2, and add 1 */ - /* negation and adding 1 are done */ - /* at the same time by the SUBI */ - extru x2,30,31,x2 - sh1add x2,x2,x2 /* multiply by 3 to get started */ -LSYM(neg) - shd x1,x2,28,t1 /* multiply by 0x11 */ - shd x2,0,28,t2 - add x2,t2,x2 - addc x1,t1,x1 -LSYM(neg_for_17) - shd x1,x2,24,t1 /* multiply by 0x101 */ - shd x2,0,24,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,16,t1 /* multiply by 0x10001 */ - shd x2,0,16,t2 - add x2,t2,x2 - addc x1,t1,x1 - MILLIRET - sub 0,x1,x1 - -/* DIVISION BY 12 (shift to divide by 4 then divide by 3) */ -GSYM($$divI_12) - .export $$divI_12,millicode - comb,< x2,0,LREF(neg12) - copy 0,x1 - extru x2,29,30,x2 /* divide by 4 */ - addib,tr 1,x2,LREF(pos) /* compute 5*(x2+1) = 5*x2+5 */ - sh2add x2,x2,x2 /* multiply by 5 to get started */ - -LSYM(neg12) - subi 4,x2,x2 /* negate, divide by 4, and add 1 */ - /* negation and adding 1 are done */ - /* at the same time by the SUBI */ - extru x2,29,30,x2 - b LREF(neg) - sh2add x2,x2,x2 /* multiply by 5 to get started */ - -GSYM($$divU_12) - .export $$divU_12,millicode - extru x2,29,30,x2 /* divide by 4 */ - addi 5,x2,t1 /* cannot carry */ - sh2add x2,t1,x2 /* multiply by 5 to get started */ - b LREF(pos) - addc 0,0,x1 - -/* DIVISION BY 15 (use z = 2**32; a = 11111111) */ -GSYM($$divI_15) - .export $$divI_15,millicode - comb,< x2,0,LREF(neg15) - copy 0,x1 - addib,tr 1,x2,LREF(pos)+4 - shd x1,x2,28,t1 - -LSYM(neg15) - b LREF(neg) - subi 1,x2,x2 - -GSYM($$divU_15) - .export $$divU_15,millicode - addi 1,x2,x2 /* this CAN overflow */ - b LREF(pos) - addc 0,0,x1 - -/* DIVISION BY 17 (use z = 2**32; a = f0f0f0f) */ -GSYM($$divI_17) - .export $$divI_17,millicode - comb,<,n x2,0,LREF(neg17) - addi 1,x2,x2 /* this cannot overflow */ - shd 0,x2,28,t1 /* multiply by 0xf to get started */ - shd x2,0,28,t2 - sub t2,x2,x2 - b LREF(pos_for_17) - subb t1,0,x1 - -LSYM(neg17) - subi 1,x2,x2 /* this cannot overflow */ - shd 0,x2,28,t1 /* multiply by 0xf to get started */ - shd x2,0,28,t2 - sub t2,x2,x2 - b LREF(neg_for_17) - subb t1,0,x1 - -GSYM($$divU_17) - .export $$divU_17,millicode - addi 1,x2,x2 /* this CAN overflow */ - addc 0,0,x1 - shd x1,x2,28,t1 /* multiply by 0xf to get started */ -LSYM(u17) - shd x2,0,28,t2 - sub t2,x2,x2 - b LREF(pos_for_17) - subb t1,x1,x1 - - -/* DIVISION BY DIVISORS OF FFFFFF, and powers of 2 times these - includes 7,9 and also 14 - - - z = 2**24-1 - r = z mod x = 0 - - so choose b = 0 - - Also, in order to divide by z = 2**24-1, we approximate by dividing - by (z+1) = 2**24 (which is easy), and then correcting. - - (ax) = (z+1)q' + r - . = zq' + (q'+r) - - So to compute (ax)/z, compute q' = (ax)/(z+1) and r = (ax) mod (z+1) - Then the true remainder of (ax)/z is (q'+r). Repeat the process - with this new remainder, adding the tentative quotients together, - until a tentative quotient is 0 (and then we are done). There is - one last correction to be done. It is possible that (q'+r) = z. - If so, then (q'+r)/(z+1) = 0 and it looks like we are done. But, - in fact, we need to add 1 more to the quotient. Now, it turns - out that this happens if and only if the original value x is - an exact multiple of y. So, to avoid a three instruction test at - the end, instead use 1 instruction to add 1 to x at the beginning. */ - -/* DIVISION BY 7 (use z = 2**24-1; a = 249249) */ -GSYM($$divI_7) - .export $$divI_7,millicode - comb,<,n x2,0,LREF(neg7) -LSYM(7) - addi 1,x2,x2 /* cannot overflow */ - shd 0,x2,29,x1 - sh3add x2,x2,x2 - addc x1,0,x1 -LSYM(pos7) - shd x1,x2,26,t1 - shd x2,0,26,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,20,t1 - shd x2,0,20,t2 - add x2,t2,x2 - addc x1,t1,t1 - - /* computed <t1,x2>. Now divide it by (2**24 - 1) */ - - copy 0,x1 - shd,= t1,x2,24,t1 /* tentative quotient */ -LSYM(1) - addb,tr t1,x1,LREF(2) /* add to previous quotient */ - extru x2,31,24,x2 /* new remainder (unadjusted) */ - - MILLIRETN - -LSYM(2) - addb,tr t1,x2,LREF(1) /* adjust remainder */ - extru,= x2,7,8,t1 /* new quotient */ - -LSYM(neg7) - subi 1,x2,x2 /* negate x2 and add 1 */ -LSYM(8) - shd 0,x2,29,x1 - sh3add x2,x2,x2 - addc x1,0,x1 - -LSYM(neg7_shift) - shd x1,x2,26,t1 - shd x2,0,26,t2 - add x2,t2,x2 - addc x1,t1,x1 - - shd x1,x2,20,t1 - shd x2,0,20,t2 - add x2,t2,x2 - addc x1,t1,t1 - - /* computed <t1,x2>. Now divide it by (2**24 - 1) */ - - copy 0,x1 - shd,= t1,x2,24,t1 /* tentative quotient */ -LSYM(3) - addb,tr t1,x1,LREF(4) /* add to previous quotient */ - extru x2,31,24,x2 /* new remainder (unadjusted) */ - - MILLIRET - sub 0,x1,x1 /* negate result */ - -LSYM(4) - addb,tr t1,x2,LREF(3) /* adjust remainder */ - extru,= x2,7,8,t1 /* new quotient */ - -GSYM($$divU_7) - .export $$divU_7,millicode - addi 1,x2,x2 /* can carry */ - addc 0,0,x1 - shd x1,x2,29,t1 - sh3add x2,x2,x2 - b LREF(pos7) - addc t1,x1,x1 - -/* DIVISION BY 9 (use z = 2**24-1; a = 1c71c7) */ -GSYM($$divI_9) - .export $$divI_9,millicode - comb,<,n x2,0,LREF(neg9) - addi 1,x2,x2 /* cannot overflow */ - shd 0,x2,29,t1 - shd x2,0,29,t2 - sub t2,x2,x2 - b LREF(pos7) - subb t1,0,x1 - -LSYM(neg9) - subi 1,x2,x2 /* negate and add 1 */ - shd 0,x2,29,t1 - shd x2,0,29,t2 - sub t2,x2,x2 - b LREF(neg7_shift) - subb t1,0,x1 - -GSYM($$divU_9) - .export $$divU_9,millicode - addi 1,x2,x2 /* can carry */ - addc 0,0,x1 - shd x1,x2,29,t1 - shd x2,0,29,t2 - sub t2,x2,x2 - b LREF(pos7) - subb t1,x1,x1 - -/* DIVISION BY 14 (shift to divide by 2 then divide by 7) */ -GSYM($$divI_14) - .export $$divI_14,millicode - comb,<,n x2,0,LREF(neg14) -GSYM($$divU_14) - .export $$divU_14,millicode - b LREF(7) /* go to 7 case */ - extru x2,30,31,x2 /* divide by 2 */ - -LSYM(neg14) - subi 2,x2,x2 /* negate (and add 2) */ - b LREF(8) - extru x2,30,31,x2 /* divide by 2 */ - .exit - .procend - .end -#endif - -#ifdef L_mulI -/* VERSION "@(#)$$mulI $ Revision: 12.4 $ $ Date: 94/03/17 17:18:51 $" */ -/****************************************************************************** -This routine is used on PA2.0 processors when gcc -mno-fpregs is used - -ROUTINE: $$mulI - - -DESCRIPTION: - - $$mulI multiplies two single word integers, giving a single - word result. - - -INPUT REGISTERS: - - arg0 = Operand 1 - arg1 = Operand 2 - r31 == return pc - sr0 == return space when called externally - - -OUTPUT REGISTERS: - - arg0 = undefined - arg1 = undefined - ret1 = result - -OTHER REGISTERS AFFECTED: - - r1 = undefined - -SIDE EFFECTS: - - Causes a trap under the following conditions: NONE - Changes memory at the following places: NONE - -PERMISSIBLE CONTEXT: - - Unwindable - Does not create a stack frame - Is usable for internal or external microcode - -DISCUSSION: - - Calls other millicode routines via mrp: NONE - Calls other millicode routines: NONE - -***************************************************************************/ - - -#define a0 %arg0 -#define a1 %arg1 -#define t0 %r1 -#define r %ret1 - -#define a0__128a0 zdep a0,24,25,a0 -#define a0__256a0 zdep a0,23,24,a0 -#define a1_ne_0_b_l0 comb,<> a1,0,LREF(l0) -#define a1_ne_0_b_l1 comb,<> a1,0,LREF(l1) -#define a1_ne_0_b_l2 comb,<> a1,0,LREF(l2) -#define b_n_ret_t0 b,n LREF(ret_t0) -#define b_e_shift b LREF(e_shift) -#define b_e_t0ma0 b LREF(e_t0ma0) -#define b_e_t0 b LREF(e_t0) -#define b_e_t0a0 b LREF(e_t0a0) -#define b_e_t02a0 b LREF(e_t02a0) -#define b_e_t04a0 b LREF(e_t04a0) -#define b_e_2t0 b LREF(e_2t0) -#define b_e_2t0a0 b LREF(e_2t0a0) -#define b_e_2t04a0 b LREF(e2t04a0) -#define b_e_3t0 b LREF(e_3t0) -#define b_e_4t0 b LREF(e_4t0) -#define b_e_4t0a0 b LREF(e_4t0a0) -#define b_e_4t08a0 b LREF(e4t08a0) -#define b_e_5t0 b LREF(e_5t0) -#define b_e_8t0 b LREF(e_8t0) -#define b_e_8t0a0 b LREF(e_8t0a0) -#define r__r_a0 add r,a0,r -#define r__r_2a0 sh1add a0,r,r -#define r__r_4a0 sh2add a0,r,r -#define r__r_8a0 sh3add a0,r,r -#define r__r_t0 add r,t0,r -#define r__r_2t0 sh1add t0,r,r -#define r__r_4t0 sh2add t0,r,r -#define r__r_8t0 sh3add t0,r,r -#define t0__3a0 sh1add a0,a0,t0 -#define t0__4a0 sh2add a0,0,t0 -#define t0__5a0 sh2add a0,a0,t0 -#define t0__8a0 sh3add a0,0,t0 -#define t0__9a0 sh3add a0,a0,t0 -#define t0__16a0 zdep a0,27,28,t0 -#define t0__32a0 zdep a0,26,27,t0 -#define t0__64a0 zdep a0,25,26,t0 -#define t0__128a0 zdep a0,24,25,t0 -#define t0__t0ma0 sub t0,a0,t0 -#define t0__t0_a0 add t0,a0,t0 -#define t0__t0_2a0 sh1add a0,t0,t0 -#define t0__t0_4a0 sh2add a0,t0,t0 -#define t0__t0_8a0 sh3add a0,t0,t0 -#define t0__2t0_a0 sh1add t0,a0,t0 -#define t0__3t0 sh1add t0,t0,t0 -#define t0__4t0 sh2add t0,0,t0 -#define t0__4t0_a0 sh2add t0,a0,t0 -#define t0__5t0 sh2add t0,t0,t0 -#define t0__8t0 sh3add t0,0,t0 -#define t0__8t0_a0 sh3add t0,a0,t0 -#define t0__9t0 sh3add t0,t0,t0 -#define t0__16t0 zdep t0,27,28,t0 -#define t0__32t0 zdep t0,26,27,t0 -#define t0__256a0 zdep a0,23,24,t0 - - - SUBSPA_MILLI - ATTR_MILLI - .align 16 - .proc - .callinfo millicode - .export $$mulI,millicode -GSYM($$mulI) - combt,<<= a1,a0,LREF(l4) /* swap args if unsigned a1>a0 */ - copy 0,r /* zero out the result */ - xor a0,a1,a0 /* swap a0 & a1 using the */ - xor a0,a1,a1 /* old xor trick */ - xor a0,a1,a0 -LSYM(l4) - combt,<= 0,a0,LREF(l3) /* if a0>=0 then proceed like unsigned */ - zdep a1,30,8,t0 /* t0 = (a1&0xff)<<1 ********* */ - sub,> 0,a1,t0 /* otherwise negate both and */ - combt,<=,n a0,t0,LREF(l2) /* swap back if |a0|<|a1| */ - sub 0,a0,a1 - movb,tr,n t0,a0,LREF(l2) /* 10th inst. */ - -LSYM(l0) r__r_t0 /* add in this partial product */ -LSYM(l1) a0__256a0 /* a0 <<= 8 ****************** */ -LSYM(l2) zdep a1,30,8,t0 /* t0 = (a1&0xff)<<1 ********* */ -LSYM(l3) blr t0,0 /* case on these 8 bits ****** */ - extru a1,23,24,a1 /* a1 >>= 8 ****************** */ - -/*16 insts before this. */ -/* a0 <<= 8 ************************** */ -LSYM(x0) a1_ne_0_b_l2 ! a0__256a0 ! MILLIRETN ! nop -LSYM(x1) a1_ne_0_b_l1 ! r__r_a0 ! MILLIRETN ! nop -LSYM(x2) a1_ne_0_b_l1 ! r__r_2a0 ! MILLIRETN ! nop -LSYM(x3) a1_ne_0_b_l0 ! t0__3a0 ! MILLIRET ! r__r_t0 -LSYM(x4) a1_ne_0_b_l1 ! r__r_4a0 ! MILLIRETN ! nop -LSYM(x5) a1_ne_0_b_l0 ! t0__5a0 ! MILLIRET ! r__r_t0 -LSYM(x6) t0__3a0 ! a1_ne_0_b_l1 ! r__r_2t0 ! MILLIRETN -LSYM(x7) t0__3a0 ! a1_ne_0_b_l0 ! r__r_4a0 ! b_n_ret_t0 -LSYM(x8) a1_ne_0_b_l1 ! r__r_8a0 ! MILLIRETN ! nop -LSYM(x9) a1_ne_0_b_l0 ! t0__9a0 ! MILLIRET ! r__r_t0 -LSYM(x10) t0__5a0 ! a1_ne_0_b_l1 ! r__r_2t0 ! MILLIRETN -LSYM(x11) t0__3a0 ! a1_ne_0_b_l0 ! r__r_8a0 ! b_n_ret_t0 -LSYM(x12) t0__3a0 ! a1_ne_0_b_l1 ! r__r_4t0 ! MILLIRETN -LSYM(x13) t0__5a0 ! a1_ne_0_b_l0 ! r__r_8a0 ! b_n_ret_t0 -LSYM(x14) t0__3a0 ! t0__2t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x15) t0__5a0 ! a1_ne_0_b_l0 ! t0__3t0 ! b_n_ret_t0 -LSYM(x16) t0__16a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x17) t0__9a0 ! a1_ne_0_b_l0 ! t0__t0_8a0 ! b_n_ret_t0 -LSYM(x18) t0__9a0 ! a1_ne_0_b_l1 ! r__r_2t0 ! MILLIRETN -LSYM(x19) t0__9a0 ! a1_ne_0_b_l0 ! t0__2t0_a0 ! b_n_ret_t0 -LSYM(x20) t0__5a0 ! a1_ne_0_b_l1 ! r__r_4t0 ! MILLIRETN -LSYM(x21) t0__5a0 ! a1_ne_0_b_l0 ! t0__4t0_a0 ! b_n_ret_t0 -LSYM(x22) t0__5a0 ! t0__2t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x23) t0__5a0 ! t0__2t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x24) t0__3a0 ! a1_ne_0_b_l1 ! r__r_8t0 ! MILLIRETN -LSYM(x25) t0__5a0 ! a1_ne_0_b_l0 ! t0__5t0 ! b_n_ret_t0 -LSYM(x26) t0__3a0 ! t0__4t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x27) t0__3a0 ! a1_ne_0_b_l0 ! t0__9t0 ! b_n_ret_t0 -LSYM(x28) t0__3a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x29) t0__3a0 ! t0__2t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x30) t0__5a0 ! t0__3t0 ! b_e_shift ! r__r_2t0 -LSYM(x31) t0__32a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -LSYM(x32) t0__32a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x33) t0__8a0 ! a1_ne_0_b_l0 ! t0__4t0_a0 ! b_n_ret_t0 -LSYM(x34) t0__16a0 ! t0__t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x35) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__t0_8a0 -LSYM(x36) t0__9a0 ! a1_ne_0_b_l1 ! r__r_4t0 ! MILLIRETN -LSYM(x37) t0__9a0 ! a1_ne_0_b_l0 ! t0__4t0_a0 ! b_n_ret_t0 -LSYM(x38) t0__9a0 ! t0__2t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x39) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x40) t0__5a0 ! a1_ne_0_b_l1 ! r__r_8t0 ! MILLIRETN -LSYM(x41) t0__5a0 ! a1_ne_0_b_l0 ! t0__8t0_a0 ! b_n_ret_t0 -LSYM(x42) t0__5a0 ! t0__4t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x43) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x44) t0__5a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x45) t0__9a0 ! a1_ne_0_b_l0 ! t0__5t0 ! b_n_ret_t0 -LSYM(x46) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__t0_a0 -LSYM(x47) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__t0_2a0 -LSYM(x48) t0__3a0 ! a1_ne_0_b_l0 ! t0__16t0 ! b_n_ret_t0 -LSYM(x49) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__t0_4a0 -LSYM(x50) t0__5a0 ! t0__5t0 ! b_e_shift ! r__r_2t0 -LSYM(x51) t0__9a0 ! t0__t0_8a0 ! b_e_t0 ! t0__3t0 -LSYM(x52) t0__3a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x53) t0__3a0 ! t0__4t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x54) t0__9a0 ! t0__3t0 ! b_e_shift ! r__r_2t0 -LSYM(x55) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x56) t0__3a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x57) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x58) t0__3a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x59) t0__9a0 ! t0__2t0_a0 ! b_e_t02a0 ! t0__3t0 -LSYM(x60) t0__5a0 ! t0__3t0 ! b_e_shift ! r__r_4t0 -LSYM(x61) t0__5a0 ! t0__3t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x62) t0__32a0 ! t0__t0ma0 ! b_e_shift ! r__r_2t0 -LSYM(x63) t0__64a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -LSYM(x64) t0__64a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x65) t0__8a0 ! a1_ne_0_b_l0 ! t0__8t0_a0 ! b_n_ret_t0 -LSYM(x66) t0__32a0 ! t0__t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x67) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x68) t0__8a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x69) t0__8a0 ! t0__2t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x70) t0__64a0 ! t0__t0_4a0 ! b_e_t0 ! t0__t0_2a0 -LSYM(x71) t0__9a0 ! t0__8t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x72) t0__9a0 ! a1_ne_0_b_l1 ! r__r_8t0 ! MILLIRETN -LSYM(x73) t0__9a0 ! t0__8t0_a0 ! b_e_shift ! r__r_t0 -LSYM(x74) t0__9a0 ! t0__4t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x75) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x76) t0__9a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x77) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x78) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x79) t0__16a0 ! t0__5t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x80) t0__16a0 ! t0__5t0 ! b_e_shift ! r__r_t0 -LSYM(x81) t0__9a0 ! t0__9t0 ! b_e_shift ! r__r_t0 -LSYM(x82) t0__5a0 ! t0__8t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x83) t0__5a0 ! t0__8t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x84) t0__5a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x85) t0__8a0 ! t0__2t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x86) t0__5a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x87) t0__9a0 ! t0__9t0 ! b_e_t02a0 ! t0__t0_4a0 -LSYM(x88) t0__5a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x89) t0__5a0 ! t0__2t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x90) t0__9a0 ! t0__5t0 ! b_e_shift ! r__r_2t0 -LSYM(x91) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x92) t0__5a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x93) t0__32a0 ! t0__t0ma0 ! b_e_t0 ! t0__3t0 -LSYM(x94) t0__9a0 ! t0__5t0 ! b_e_2t0 ! t0__t0_2a0 -LSYM(x95) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x96) t0__8a0 ! t0__3t0 ! b_e_shift ! r__r_4t0 -LSYM(x97) t0__8a0 ! t0__3t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x98) t0__32a0 ! t0__3t0 ! b_e_t0 ! t0__t0_2a0 -LSYM(x99) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x100) t0__5a0 ! t0__5t0 ! b_e_shift ! r__r_4t0 -LSYM(x101) t0__5a0 ! t0__5t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x102) t0__32a0 ! t0__t0_2a0 ! b_e_t0 ! t0__3t0 -LSYM(x103) t0__5a0 ! t0__5t0 ! b_e_t02a0 ! t0__4t0_a0 -LSYM(x104) t0__3a0 ! t0__4t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x105) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x106) t0__3a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x107) t0__9a0 ! t0__t0_4a0 ! b_e_t02a0 ! t0__8t0_a0 -LSYM(x108) t0__9a0 ! t0__3t0 ! b_e_shift ! r__r_4t0 -LSYM(x109) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x110) t0__9a0 ! t0__3t0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x111) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x112) t0__3a0 ! t0__2t0_a0 ! b_e_t0 ! t0__16t0 -LSYM(x113) t0__9a0 ! t0__4t0_a0 ! b_e_t02a0 ! t0__3t0 -LSYM(x114) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__3t0 -LSYM(x115) t0__9a0 ! t0__2t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x116) t0__3a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__4t0_a0 -LSYM(x117) t0__3a0 ! t0__4t0_a0 ! b_e_t0 ! t0__9t0 -LSYM(x118) t0__3a0 ! t0__4t0_a0 ! b_e_t0a0 ! t0__9t0 -LSYM(x119) t0__3a0 ! t0__4t0_a0 ! b_e_t02a0 ! t0__9t0 -LSYM(x120) t0__5a0 ! t0__3t0 ! b_e_shift ! r__r_8t0 -LSYM(x121) t0__5a0 ! t0__3t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x122) t0__5a0 ! t0__3t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x123) t0__5a0 ! t0__8t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x124) t0__32a0 ! t0__t0ma0 ! b_e_shift ! r__r_4t0 -LSYM(x125) t0__5a0 ! t0__5t0 ! b_e_t0 ! t0__5t0 -LSYM(x126) t0__64a0 ! t0__t0ma0 ! b_e_shift ! r__r_2t0 -LSYM(x127) t0__128a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -LSYM(x128) t0__128a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x129) t0__128a0 ! a1_ne_0_b_l0 ! t0__t0_a0 ! b_n_ret_t0 -LSYM(x130) t0__64a0 ! t0__t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x131) t0__8a0 ! t0__8t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x132) t0__8a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x133) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x134) t0__8a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x135) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__3t0 -LSYM(x136) t0__8a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x137) t0__8a0 ! t0__2t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x138) t0__8a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x139) t0__8a0 ! t0__2t0_a0 ! b_e_2t0a0 ! t0__4t0_a0 -LSYM(x140) t0__3a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__5t0 -LSYM(x141) t0__8a0 ! t0__2t0_a0 ! b_e_4t0a0 ! t0__2t0_a0 -LSYM(x142) t0__9a0 ! t0__8t0 ! b_e_2t0 ! t0__t0ma0 -LSYM(x143) t0__16a0 ! t0__9t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x144) t0__9a0 ! t0__8t0 ! b_e_shift ! r__r_2t0 -LSYM(x145) t0__9a0 ! t0__8t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x146) t0__9a0 ! t0__8t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x147) t0__9a0 ! t0__8t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x148) t0__9a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x149) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x150) t0__9a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x151) t0__9a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__2t0_a0 -LSYM(x152) t0__9a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x153) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x154) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x155) t0__32a0 ! t0__t0ma0 ! b_e_t0 ! t0__5t0 -LSYM(x156) t0__9a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x157) t0__32a0 ! t0__t0ma0 ! b_e_t02a0 ! t0__5t0 -LSYM(x158) t0__16a0 ! t0__5t0 ! b_e_2t0 ! t0__t0ma0 -LSYM(x159) t0__32a0 ! t0__5t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x160) t0__5a0 ! t0__4t0 ! b_e_shift ! r__r_8t0 -LSYM(x161) t0__8a0 ! t0__5t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x162) t0__9a0 ! t0__9t0 ! b_e_shift ! r__r_2t0 -LSYM(x163) t0__9a0 ! t0__9t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x164) t0__5a0 ! t0__8t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x165) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x166) t0__5a0 ! t0__8t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x167) t0__5a0 ! t0__8t0_a0 ! b_e_2t0a0 ! t0__2t0_a0 -LSYM(x168) t0__5a0 ! t0__4t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x169) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x170) t0__32a0 ! t0__t0_2a0 ! b_e_t0 ! t0__5t0 -LSYM(x171) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__9t0 -LSYM(x172) t0__5a0 ! t0__4t0_a0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x173) t0__9a0 ! t0__2t0_a0 ! b_e_t02a0 ! t0__9t0 -LSYM(x174) t0__32a0 ! t0__t0_2a0 ! b_e_t04a0 ! t0__5t0 -LSYM(x175) t0__8a0 ! t0__2t0_a0 ! b_e_5t0 ! t0__2t0_a0 -LSYM(x176) t0__5a0 ! t0__4t0_a0 ! b_e_8t0 ! t0__t0_a0 -LSYM(x177) t0__5a0 ! t0__4t0_a0 ! b_e_8t0a0 ! t0__t0_a0 -LSYM(x178) t0__5a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__8t0_a0 -LSYM(x179) t0__5a0 ! t0__2t0_a0 ! b_e_2t0a0 ! t0__8t0_a0 -LSYM(x180) t0__9a0 ! t0__5t0 ! b_e_shift ! r__r_4t0 -LSYM(x181) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x182) t0__9a0 ! t0__5t0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x183) t0__9a0 ! t0__5t0 ! b_e_2t0a0 ! t0__2t0_a0 -LSYM(x184) t0__5a0 ! t0__9t0 ! b_e_4t0 ! t0__t0_a0 -LSYM(x185) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x186) t0__32a0 ! t0__t0ma0 ! b_e_2t0 ! t0__3t0 -LSYM(x187) t0__9a0 ! t0__4t0_a0 ! b_e_t02a0 ! t0__5t0 -LSYM(x188) t0__9a0 ! t0__5t0 ! b_e_4t0 ! t0__t0_2a0 -LSYM(x189) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__9t0 -LSYM(x190) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__5t0 -LSYM(x191) t0__64a0 ! t0__3t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x192) t0__8a0 ! t0__3t0 ! b_e_shift ! r__r_8t0 -LSYM(x193) t0__8a0 ! t0__3t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x194) t0__8a0 ! t0__3t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x195) t0__8a0 ! t0__8t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x196) t0__8a0 ! t0__3t0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x197) t0__8a0 ! t0__3t0 ! b_e_4t0a0 ! t0__2t0_a0 -LSYM(x198) t0__64a0 ! t0__t0_2a0 ! b_e_t0 ! t0__3t0 -LSYM(x199) t0__8a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x200) t0__5a0 ! t0__5t0 ! b_e_shift ! r__r_8t0 -LSYM(x201) t0__5a0 ! t0__5t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x202) t0__5a0 ! t0__5t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x203) t0__5a0 ! t0__5t0 ! b_e_2t0a0 ! t0__4t0_a0 -LSYM(x204) t0__8a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__3t0 -LSYM(x205) t0__5a0 ! t0__8t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x206) t0__64a0 ! t0__t0_4a0 ! b_e_t02a0 ! t0__3t0 -LSYM(x207) t0__8a0 ! t0__2t0_a0 ! b_e_3t0 ! t0__4t0_a0 -LSYM(x208) t0__5a0 ! t0__5t0 ! b_e_8t0 ! t0__t0_a0 -LSYM(x209) t0__5a0 ! t0__5t0 ! b_e_8t0a0 ! t0__t0_a0 -LSYM(x210) t0__5a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__5t0 -LSYM(x211) t0__5a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__5t0 -LSYM(x212) t0__3a0 ! t0__4t0_a0 ! b_e_4t0 ! t0__4t0_a0 -LSYM(x213) t0__3a0 ! t0__4t0_a0 ! b_e_4t0a0 ! t0__4t0_a0 -LSYM(x214) t0__9a0 ! t0__t0_4a0 ! b_e_2t04a0 ! t0__8t0_a0 -LSYM(x215) t0__5a0 ! t0__4t0_a0 ! b_e_5t0 ! t0__2t0_a0 -LSYM(x216) t0__9a0 ! t0__3t0 ! b_e_shift ! r__r_8t0 -LSYM(x217) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x218) t0__9a0 ! t0__3t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x219) t0__9a0 ! t0__8t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x220) t0__3a0 ! t0__9t0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x221) t0__3a0 ! t0__9t0 ! b_e_4t0a0 ! t0__2t0_a0 -LSYM(x222) t0__9a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__3t0 -LSYM(x223) t0__9a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x224) t0__9a0 ! t0__3t0 ! b_e_8t0 ! t0__t0_a0 -LSYM(x225) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__5t0 -LSYM(x226) t0__3a0 ! t0__2t0_a0 ! b_e_t02a0 ! t0__32t0 -LSYM(x227) t0__9a0 ! t0__5t0 ! b_e_t02a0 ! t0__5t0 -LSYM(x228) t0__9a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__3t0 -LSYM(x229) t0__9a0 ! t0__2t0_a0 ! b_e_4t0a0 ! t0__3t0 -LSYM(x230) t0__9a0 ! t0__5t0 ! b_e_5t0 ! t0__t0_a0 -LSYM(x231) t0__9a0 ! t0__2t0_a0 ! b_e_3t0 ! t0__4t0_a0 -LSYM(x232) t0__3a0 ! t0__2t0_a0 ! b_e_8t0 ! t0__4t0_a0 -LSYM(x233) t0__3a0 ! t0__2t0_a0 ! b_e_8t0a0 ! t0__4t0_a0 -LSYM(x234) t0__3a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__9t0 -LSYM(x235) t0__3a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__9t0 -LSYM(x236) t0__9a0 ! t0__2t0_a0 ! b_e_4t08a0 ! t0__3t0 -LSYM(x237) t0__16a0 ! t0__5t0 ! b_e_3t0 ! t0__t0ma0 -LSYM(x238) t0__3a0 ! t0__4t0_a0 ! b_e_2t04a0 ! t0__9t0 -LSYM(x239) t0__16a0 ! t0__5t0 ! b_e_t0ma0 ! t0__3t0 -LSYM(x240) t0__9a0 ! t0__t0_a0 ! b_e_8t0 ! t0__3t0 -LSYM(x241) t0__9a0 ! t0__t0_a0 ! b_e_8t0a0 ! t0__3t0 -LSYM(x242) t0__5a0 ! t0__3t0 ! b_e_2t0 ! t0__8t0_a0 -LSYM(x243) t0__9a0 ! t0__9t0 ! b_e_t0 ! t0__3t0 -LSYM(x244) t0__5a0 ! t0__3t0 ! b_e_4t0 ! t0__4t0_a0 -LSYM(x245) t0__8a0 ! t0__3t0 ! b_e_5t0 ! t0__2t0_a0 -LSYM(x246) t0__5a0 ! t0__8t0_a0 ! b_e_2t0 ! t0__3t0 -LSYM(x247) t0__5a0 ! t0__8t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x248) t0__32a0 ! t0__t0ma0 ! b_e_shift ! r__r_8t0 -LSYM(x249) t0__32a0 ! t0__t0ma0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x250) t0__5a0 ! t0__5t0 ! b_e_2t0 ! t0__5t0 -LSYM(x251) t0__5a0 ! t0__5t0 ! b_e_2t0a0 ! t0__5t0 -LSYM(x252) t0__64a0 ! t0__t0ma0 ! b_e_shift ! r__r_4t0 -LSYM(x253) t0__64a0 ! t0__t0ma0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x254) t0__128a0 ! t0__t0ma0 ! b_e_shift ! r__r_2t0 -LSYM(x255) t0__256a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -/*1040 insts before this. */ -LSYM(ret_t0) MILLIRET -LSYM(e_t0) r__r_t0 -LSYM(e_shift) a1_ne_0_b_l2 - a0__256a0 /* a0 <<= 8 *********** */ - MILLIRETN -LSYM(e_t0ma0) a1_ne_0_b_l0 - t0__t0ma0 - MILLIRET - r__r_t0 -LSYM(e_t0a0) a1_ne_0_b_l0 - t0__t0_a0 - MILLIRET - r__r_t0 -LSYM(e_t02a0) a1_ne_0_b_l0 - t0__t0_2a0 - MILLIRET - r__r_t0 -LSYM(e_t04a0) a1_ne_0_b_l0 - t0__t0_4a0 - MILLIRET - r__r_t0 -LSYM(e_2t0) a1_ne_0_b_l1 - r__r_2t0 - MILLIRETN -LSYM(e_2t0a0) a1_ne_0_b_l0 - t0__2t0_a0 - MILLIRET - r__r_t0 -LSYM(e2t04a0) t0__t0_2a0 - a1_ne_0_b_l1 - r__r_2t0 - MILLIRETN -LSYM(e_3t0) a1_ne_0_b_l0 - t0__3t0 - MILLIRET - r__r_t0 -LSYM(e_4t0) a1_ne_0_b_l1 - r__r_4t0 - MILLIRETN -LSYM(e_4t0a0) a1_ne_0_b_l0 - t0__4t0_a0 - MILLIRET - r__r_t0 -LSYM(e4t08a0) t0__t0_2a0 - a1_ne_0_b_l1 - r__r_4t0 - MILLIRETN -LSYM(e_5t0) a1_ne_0_b_l0 - t0__5t0 - MILLIRET - r__r_t0 -LSYM(e_8t0) a1_ne_0_b_l1 - r__r_8t0 - MILLIRETN -LSYM(e_8t0a0) a1_ne_0_b_l0 - t0__8t0_a0 - MILLIRET - r__r_t0 - - .procend - .end -#endif diff --git a/arch/parisc/lib/milli/milli.h b/arch/parisc/lib/milli/milli.h deleted file mode 100644 index 19ac79f336de..000000000000 --- a/arch/parisc/lib/milli/milli.h +++ /dev/null @@ -1,165 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#ifndef _PA_MILLI_H_ -#define _PA_MILLI_H_ - -#define L_dyncall -#define L_divI -#define L_divU -#define L_remI -#define L_remU -#define L_div_const -#define L_mulI - -#ifdef CONFIG_64BIT - .level 2.0w -#endif - -/* Hardware General Registers. */ -r0: .reg %r0 -r1: .reg %r1 -r2: .reg %r2 -r3: .reg %r3 -r4: .reg %r4 -r5: .reg %r5 -r6: .reg %r6 -r7: .reg %r7 -r8: .reg %r8 -r9: .reg %r9 -r10: .reg %r10 -r11: .reg %r11 -r12: .reg %r12 -r13: .reg %r13 -r14: .reg %r14 -r15: .reg %r15 -r16: .reg %r16 -r17: .reg %r17 -r18: .reg %r18 -r19: .reg %r19 -r20: .reg %r20 -r21: .reg %r21 -r22: .reg %r22 -r23: .reg %r23 -r24: .reg %r24 -r25: .reg %r25 -r26: .reg %r26 -r27: .reg %r27 -r28: .reg %r28 -r29: .reg %r29 -r30: .reg %r30 -r31: .reg %r31 - -/* Hardware Space Registers. */ -sr0: .reg %sr0 -sr1: .reg %sr1 -sr2: .reg %sr2 -sr3: .reg %sr3 -sr4: .reg %sr4 -sr5: .reg %sr5 -sr6: .reg %sr6 -sr7: .reg %sr7 - -/* Hardware Floating Point Registers. */ -fr0: .reg %fr0 -fr1: .reg %fr1 -fr2: .reg %fr2 -fr3: .reg %fr3 -fr4: .reg %fr4 -fr5: .reg %fr5 -fr6: .reg %fr6 -fr7: .reg %fr7 -fr8: .reg %fr8 -fr9: .reg %fr9 -fr10: .reg %fr10 -fr11: .reg %fr11 -fr12: .reg %fr12 -fr13: .reg %fr13 -fr14: .reg %fr14 -fr15: .reg %fr15 - -/* Hardware Control Registers. */ -cr11: .reg %cr11 -sar: .reg %cr11 /* Shift Amount Register */ - -/* Software Architecture General Registers. */ -rp: .reg r2 /* return pointer */ -#ifdef CONFIG_64BIT -mrp: .reg r2 /* millicode return pointer */ -#else -mrp: .reg r31 /* millicode return pointer */ -#endif -ret0: .reg r28 /* return value */ -ret1: .reg r29 /* return value (high part of double) */ -sp: .reg r30 /* stack pointer */ -dp: .reg r27 /* data pointer */ -arg0: .reg r26 /* argument */ -arg1: .reg r25 /* argument or high part of double argument */ -arg2: .reg r24 /* argument */ -arg3: .reg r23 /* argument or high part of double argument */ - -/* Software Architecture Space Registers. */ -/* sr0 ; return link from BLE */ -sret: .reg sr1 /* return value */ -sarg: .reg sr1 /* argument */ -/* sr4 ; PC SPACE tracker */ -/* sr5 ; process private data */ - -/* Frame Offsets (millicode convention!) Used when calling other - millicode routines. Stack unwinding is dependent upon these - definitions. */ -r31_slot: .equ -20 /* "current RP" slot */ -sr0_slot: .equ -16 /* "static link" slot */ -#if defined(CONFIG_64BIT) -mrp_slot: .equ -16 /* "current RP" slot */ -psp_slot: .equ -8 /* "previous SP" slot */ -#else -mrp_slot: .equ -20 /* "current RP" slot (replacing "r31_slot") */ -#endif - - -#define DEFINE(name,value)name: .EQU value -#define RDEFINE(name,value)name: .REG value -#ifdef milliext -#define MILLI_BE(lbl) BE lbl(sr7,r0) -#define MILLI_BEN(lbl) BE,n lbl(sr7,r0) -#define MILLI_BLE(lbl) BLE lbl(sr7,r0) -#define MILLI_BLEN(lbl) BLE,n lbl(sr7,r0) -#define MILLIRETN BE,n 0(sr0,mrp) -#define MILLIRET BE 0(sr0,mrp) -#define MILLI_RETN BE,n 0(sr0,mrp) -#define MILLI_RET BE 0(sr0,mrp) -#else -#define MILLI_BE(lbl) B lbl -#define MILLI_BEN(lbl) B,n lbl -#define MILLI_BLE(lbl) BL lbl,mrp -#define MILLI_BLEN(lbl) BL,n lbl,mrp -#define MILLIRETN BV,n 0(mrp) -#define MILLIRET BV 0(mrp) -#define MILLI_RETN BV,n 0(mrp) -#define MILLI_RET BV 0(mrp) -#endif - -#define CAT(a,b) a##b - -#define SUBSPA_MILLI .section .text -#define SUBSPA_MILLI_DIV .section .text.div,"ax",@progbits! .align 16 -#define SUBSPA_MILLI_MUL .section .text.mul,"ax",@progbits! .align 16 -#define ATTR_MILLI -#define SUBSPA_DATA .section .data -#define ATTR_DATA -#define GLOBAL $global$ -#define GSYM(sym) !sym: -#define LSYM(sym) !CAT(.L,sym:) -#define LREF(sym) CAT(.L,sym) - -#endif /*_PA_MILLI_H_*/ diff --git a/arch/parisc/lib/milli/mulI.S b/arch/parisc/lib/milli/mulI.S deleted file mode 100644 index 4c7e0c36d15e..000000000000 --- a/arch/parisc/lib/milli/mulI.S +++ /dev/null @@ -1,474 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#include "milli.h" - -#ifdef L_mulI -/* VERSION "@(#)$$mulI $ Revision: 12.4 $ $ Date: 94/03/17 17:18:51 $" */ -/****************************************************************************** -This routine is used on PA2.0 processors when gcc -mno-fpregs is used - -ROUTINE: $$mulI - - -DESCRIPTION: - - $$mulI multiplies two single word integers, giving a single - word result. - - -INPUT REGISTERS: - - arg0 = Operand 1 - arg1 = Operand 2 - r31 == return pc - sr0 == return space when called externally - - -OUTPUT REGISTERS: - - arg0 = undefined - arg1 = undefined - ret1 = result - -OTHER REGISTERS AFFECTED: - - r1 = undefined - -SIDE EFFECTS: - - Causes a trap under the following conditions: NONE - Changes memory at the following places: NONE - -PERMISSIBLE CONTEXT: - - Unwindable - Does not create a stack frame - Is usable for internal or external microcode - -DISCUSSION: - - Calls other millicode routines via mrp: NONE - Calls other millicode routines: NONE - -***************************************************************************/ - - -#define a0 %arg0 -#define a1 %arg1 -#define t0 %r1 -#define r %ret1 - -#define a0__128a0 zdep a0,24,25,a0 -#define a0__256a0 zdep a0,23,24,a0 -#define a1_ne_0_b_l0 comb,<> a1,0,LREF(l0) -#define a1_ne_0_b_l1 comb,<> a1,0,LREF(l1) -#define a1_ne_0_b_l2 comb,<> a1,0,LREF(l2) -#define b_n_ret_t0 b,n LREF(ret_t0) -#define b_e_shift b LREF(e_shift) -#define b_e_t0ma0 b LREF(e_t0ma0) -#define b_e_t0 b LREF(e_t0) -#define b_e_t0a0 b LREF(e_t0a0) -#define b_e_t02a0 b LREF(e_t02a0) -#define b_e_t04a0 b LREF(e_t04a0) -#define b_e_2t0 b LREF(e_2t0) -#define b_e_2t0a0 b LREF(e_2t0a0) -#define b_e_2t04a0 b LREF(e2t04a0) -#define b_e_3t0 b LREF(e_3t0) -#define b_e_4t0 b LREF(e_4t0) -#define b_e_4t0a0 b LREF(e_4t0a0) -#define b_e_4t08a0 b LREF(e4t08a0) -#define b_e_5t0 b LREF(e_5t0) -#define b_e_8t0 b LREF(e_8t0) -#define b_e_8t0a0 b LREF(e_8t0a0) -#define r__r_a0 add r,a0,r -#define r__r_2a0 sh1add a0,r,r -#define r__r_4a0 sh2add a0,r,r -#define r__r_8a0 sh3add a0,r,r -#define r__r_t0 add r,t0,r -#define r__r_2t0 sh1add t0,r,r -#define r__r_4t0 sh2add t0,r,r -#define r__r_8t0 sh3add t0,r,r -#define t0__3a0 sh1add a0,a0,t0 -#define t0__4a0 sh2add a0,0,t0 -#define t0__5a0 sh2add a0,a0,t0 -#define t0__8a0 sh3add a0,0,t0 -#define t0__9a0 sh3add a0,a0,t0 -#define t0__16a0 zdep a0,27,28,t0 -#define t0__32a0 zdep a0,26,27,t0 -#define t0__64a0 zdep a0,25,26,t0 -#define t0__128a0 zdep a0,24,25,t0 -#define t0__t0ma0 sub t0,a0,t0 -#define t0__t0_a0 add t0,a0,t0 -#define t0__t0_2a0 sh1add a0,t0,t0 -#define t0__t0_4a0 sh2add a0,t0,t0 -#define t0__t0_8a0 sh3add a0,t0,t0 -#define t0__2t0_a0 sh1add t0,a0,t0 -#define t0__3t0 sh1add t0,t0,t0 -#define t0__4t0 sh2add t0,0,t0 -#define t0__4t0_a0 sh2add t0,a0,t0 -#define t0__5t0 sh2add t0,t0,t0 -#define t0__8t0 sh3add t0,0,t0 -#define t0__8t0_a0 sh3add t0,a0,t0 -#define t0__9t0 sh3add t0,t0,t0 -#define t0__16t0 zdep t0,27,28,t0 -#define t0__32t0 zdep t0,26,27,t0 -#define t0__256a0 zdep a0,23,24,t0 - - - SUBSPA_MILLI - ATTR_MILLI - .align 16 - .proc - .callinfo millicode - .export $$mulI,millicode -GSYM($$mulI) - combt,<<= a1,a0,LREF(l4) /* swap args if unsigned a1>a0 */ - copy 0,r /* zero out the result */ - xor a0,a1,a0 /* swap a0 & a1 using the */ - xor a0,a1,a1 /* old xor trick */ - xor a0,a1,a0 -LSYM(l4) - combt,<= 0,a0,LREF(l3) /* if a0>=0 then proceed like unsigned */ - zdep a1,30,8,t0 /* t0 = (a1&0xff)<<1 ********* */ - sub,> 0,a1,t0 /* otherwise negate both and */ - combt,<=,n a0,t0,LREF(l2) /* swap back if |a0|<|a1| */ - sub 0,a0,a1 - movb,tr,n t0,a0,LREF(l2) /* 10th inst. */ - -LSYM(l0) r__r_t0 /* add in this partial product */ -LSYM(l1) a0__256a0 /* a0 <<= 8 ****************** */ -LSYM(l2) zdep a1,30,8,t0 /* t0 = (a1&0xff)<<1 ********* */ -LSYM(l3) blr t0,0 /* case on these 8 bits ****** */ - extru a1,23,24,a1 /* a1 >>= 8 ****************** */ - -/*16 insts before this. */ -/* a0 <<= 8 ************************** */ -LSYM(x0) a1_ne_0_b_l2 ! a0__256a0 ! MILLIRETN ! nop -LSYM(x1) a1_ne_0_b_l1 ! r__r_a0 ! MILLIRETN ! nop -LSYM(x2) a1_ne_0_b_l1 ! r__r_2a0 ! MILLIRETN ! nop -LSYM(x3) a1_ne_0_b_l0 ! t0__3a0 ! MILLIRET ! r__r_t0 -LSYM(x4) a1_ne_0_b_l1 ! r__r_4a0 ! MILLIRETN ! nop -LSYM(x5) a1_ne_0_b_l0 ! t0__5a0 ! MILLIRET ! r__r_t0 -LSYM(x6) t0__3a0 ! a1_ne_0_b_l1 ! r__r_2t0 ! MILLIRETN -LSYM(x7) t0__3a0 ! a1_ne_0_b_l0 ! r__r_4a0 ! b_n_ret_t0 -LSYM(x8) a1_ne_0_b_l1 ! r__r_8a0 ! MILLIRETN ! nop -LSYM(x9) a1_ne_0_b_l0 ! t0__9a0 ! MILLIRET ! r__r_t0 -LSYM(x10) t0__5a0 ! a1_ne_0_b_l1 ! r__r_2t0 ! MILLIRETN -LSYM(x11) t0__3a0 ! a1_ne_0_b_l0 ! r__r_8a0 ! b_n_ret_t0 -LSYM(x12) t0__3a0 ! a1_ne_0_b_l1 ! r__r_4t0 ! MILLIRETN -LSYM(x13) t0__5a0 ! a1_ne_0_b_l0 ! r__r_8a0 ! b_n_ret_t0 -LSYM(x14) t0__3a0 ! t0__2t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x15) t0__5a0 ! a1_ne_0_b_l0 ! t0__3t0 ! b_n_ret_t0 -LSYM(x16) t0__16a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x17) t0__9a0 ! a1_ne_0_b_l0 ! t0__t0_8a0 ! b_n_ret_t0 -LSYM(x18) t0__9a0 ! a1_ne_0_b_l1 ! r__r_2t0 ! MILLIRETN -LSYM(x19) t0__9a0 ! a1_ne_0_b_l0 ! t0__2t0_a0 ! b_n_ret_t0 -LSYM(x20) t0__5a0 ! a1_ne_0_b_l1 ! r__r_4t0 ! MILLIRETN -LSYM(x21) t0__5a0 ! a1_ne_0_b_l0 ! t0__4t0_a0 ! b_n_ret_t0 -LSYM(x22) t0__5a0 ! t0__2t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x23) t0__5a0 ! t0__2t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x24) t0__3a0 ! a1_ne_0_b_l1 ! r__r_8t0 ! MILLIRETN -LSYM(x25) t0__5a0 ! a1_ne_0_b_l0 ! t0__5t0 ! b_n_ret_t0 -LSYM(x26) t0__3a0 ! t0__4t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x27) t0__3a0 ! a1_ne_0_b_l0 ! t0__9t0 ! b_n_ret_t0 -LSYM(x28) t0__3a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x29) t0__3a0 ! t0__2t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x30) t0__5a0 ! t0__3t0 ! b_e_shift ! r__r_2t0 -LSYM(x31) t0__32a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -LSYM(x32) t0__32a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x33) t0__8a0 ! a1_ne_0_b_l0 ! t0__4t0_a0 ! b_n_ret_t0 -LSYM(x34) t0__16a0 ! t0__t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x35) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__t0_8a0 -LSYM(x36) t0__9a0 ! a1_ne_0_b_l1 ! r__r_4t0 ! MILLIRETN -LSYM(x37) t0__9a0 ! a1_ne_0_b_l0 ! t0__4t0_a0 ! b_n_ret_t0 -LSYM(x38) t0__9a0 ! t0__2t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x39) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x40) t0__5a0 ! a1_ne_0_b_l1 ! r__r_8t0 ! MILLIRETN -LSYM(x41) t0__5a0 ! a1_ne_0_b_l0 ! t0__8t0_a0 ! b_n_ret_t0 -LSYM(x42) t0__5a0 ! t0__4t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x43) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x44) t0__5a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x45) t0__9a0 ! a1_ne_0_b_l0 ! t0__5t0 ! b_n_ret_t0 -LSYM(x46) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__t0_a0 -LSYM(x47) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__t0_2a0 -LSYM(x48) t0__3a0 ! a1_ne_0_b_l0 ! t0__16t0 ! b_n_ret_t0 -LSYM(x49) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__t0_4a0 -LSYM(x50) t0__5a0 ! t0__5t0 ! b_e_shift ! r__r_2t0 -LSYM(x51) t0__9a0 ! t0__t0_8a0 ! b_e_t0 ! t0__3t0 -LSYM(x52) t0__3a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x53) t0__3a0 ! t0__4t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x54) t0__9a0 ! t0__3t0 ! b_e_shift ! r__r_2t0 -LSYM(x55) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x56) t0__3a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x57) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x58) t0__3a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x59) t0__9a0 ! t0__2t0_a0 ! b_e_t02a0 ! t0__3t0 -LSYM(x60) t0__5a0 ! t0__3t0 ! b_e_shift ! r__r_4t0 -LSYM(x61) t0__5a0 ! t0__3t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x62) t0__32a0 ! t0__t0ma0 ! b_e_shift ! r__r_2t0 -LSYM(x63) t0__64a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -LSYM(x64) t0__64a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x65) t0__8a0 ! a1_ne_0_b_l0 ! t0__8t0_a0 ! b_n_ret_t0 -LSYM(x66) t0__32a0 ! t0__t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x67) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x68) t0__8a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x69) t0__8a0 ! t0__2t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x70) t0__64a0 ! t0__t0_4a0 ! b_e_t0 ! t0__t0_2a0 -LSYM(x71) t0__9a0 ! t0__8t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x72) t0__9a0 ! a1_ne_0_b_l1 ! r__r_8t0 ! MILLIRETN -LSYM(x73) t0__9a0 ! t0__8t0_a0 ! b_e_shift ! r__r_t0 -LSYM(x74) t0__9a0 ! t0__4t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x75) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x76) t0__9a0 ! t0__2t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x77) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x78) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x79) t0__16a0 ! t0__5t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x80) t0__16a0 ! t0__5t0 ! b_e_shift ! r__r_t0 -LSYM(x81) t0__9a0 ! t0__9t0 ! b_e_shift ! r__r_t0 -LSYM(x82) t0__5a0 ! t0__8t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x83) t0__5a0 ! t0__8t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x84) t0__5a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x85) t0__8a0 ! t0__2t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x86) t0__5a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x87) t0__9a0 ! t0__9t0 ! b_e_t02a0 ! t0__t0_4a0 -LSYM(x88) t0__5a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x89) t0__5a0 ! t0__2t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x90) t0__9a0 ! t0__5t0 ! b_e_shift ! r__r_2t0 -LSYM(x91) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x92) t0__5a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x93) t0__32a0 ! t0__t0ma0 ! b_e_t0 ! t0__3t0 -LSYM(x94) t0__9a0 ! t0__5t0 ! b_e_2t0 ! t0__t0_2a0 -LSYM(x95) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x96) t0__8a0 ! t0__3t0 ! b_e_shift ! r__r_4t0 -LSYM(x97) t0__8a0 ! t0__3t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x98) t0__32a0 ! t0__3t0 ! b_e_t0 ! t0__t0_2a0 -LSYM(x99) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x100) t0__5a0 ! t0__5t0 ! b_e_shift ! r__r_4t0 -LSYM(x101) t0__5a0 ! t0__5t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x102) t0__32a0 ! t0__t0_2a0 ! b_e_t0 ! t0__3t0 -LSYM(x103) t0__5a0 ! t0__5t0 ! b_e_t02a0 ! t0__4t0_a0 -LSYM(x104) t0__3a0 ! t0__4t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x105) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x106) t0__3a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x107) t0__9a0 ! t0__t0_4a0 ! b_e_t02a0 ! t0__8t0_a0 -LSYM(x108) t0__9a0 ! t0__3t0 ! b_e_shift ! r__r_4t0 -LSYM(x109) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x110) t0__9a0 ! t0__3t0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x111) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x112) t0__3a0 ! t0__2t0_a0 ! b_e_t0 ! t0__16t0 -LSYM(x113) t0__9a0 ! t0__4t0_a0 ! b_e_t02a0 ! t0__3t0 -LSYM(x114) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__3t0 -LSYM(x115) t0__9a0 ! t0__2t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x116) t0__3a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__4t0_a0 -LSYM(x117) t0__3a0 ! t0__4t0_a0 ! b_e_t0 ! t0__9t0 -LSYM(x118) t0__3a0 ! t0__4t0_a0 ! b_e_t0a0 ! t0__9t0 -LSYM(x119) t0__3a0 ! t0__4t0_a0 ! b_e_t02a0 ! t0__9t0 -LSYM(x120) t0__5a0 ! t0__3t0 ! b_e_shift ! r__r_8t0 -LSYM(x121) t0__5a0 ! t0__3t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x122) t0__5a0 ! t0__3t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x123) t0__5a0 ! t0__8t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x124) t0__32a0 ! t0__t0ma0 ! b_e_shift ! r__r_4t0 -LSYM(x125) t0__5a0 ! t0__5t0 ! b_e_t0 ! t0__5t0 -LSYM(x126) t0__64a0 ! t0__t0ma0 ! b_e_shift ! r__r_2t0 -LSYM(x127) t0__128a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -LSYM(x128) t0__128a0 ! a1_ne_0_b_l1 ! r__r_t0 ! MILLIRETN -LSYM(x129) t0__128a0 ! a1_ne_0_b_l0 ! t0__t0_a0 ! b_n_ret_t0 -LSYM(x130) t0__64a0 ! t0__t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x131) t0__8a0 ! t0__8t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x132) t0__8a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x133) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x134) t0__8a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x135) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__3t0 -LSYM(x136) t0__8a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x137) t0__8a0 ! t0__2t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x138) t0__8a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x139) t0__8a0 ! t0__2t0_a0 ! b_e_2t0a0 ! t0__4t0_a0 -LSYM(x140) t0__3a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__5t0 -LSYM(x141) t0__8a0 ! t0__2t0_a0 ! b_e_4t0a0 ! t0__2t0_a0 -LSYM(x142) t0__9a0 ! t0__8t0 ! b_e_2t0 ! t0__t0ma0 -LSYM(x143) t0__16a0 ! t0__9t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x144) t0__9a0 ! t0__8t0 ! b_e_shift ! r__r_2t0 -LSYM(x145) t0__9a0 ! t0__8t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x146) t0__9a0 ! t0__8t0_a0 ! b_e_shift ! r__r_2t0 -LSYM(x147) t0__9a0 ! t0__8t0_a0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x148) t0__9a0 ! t0__4t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x149) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x150) t0__9a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x151) t0__9a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__2t0_a0 -LSYM(x152) t0__9a0 ! t0__2t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x153) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x154) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x155) t0__32a0 ! t0__t0ma0 ! b_e_t0 ! t0__5t0 -LSYM(x156) t0__9a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x157) t0__32a0 ! t0__t0ma0 ! b_e_t02a0 ! t0__5t0 -LSYM(x158) t0__16a0 ! t0__5t0 ! b_e_2t0 ! t0__t0ma0 -LSYM(x159) t0__32a0 ! t0__5t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x160) t0__5a0 ! t0__4t0 ! b_e_shift ! r__r_8t0 -LSYM(x161) t0__8a0 ! t0__5t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x162) t0__9a0 ! t0__9t0 ! b_e_shift ! r__r_2t0 -LSYM(x163) t0__9a0 ! t0__9t0 ! b_e_t0 ! t0__2t0_a0 -LSYM(x164) t0__5a0 ! t0__8t0_a0 ! b_e_shift ! r__r_4t0 -LSYM(x165) t0__8a0 ! t0__4t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x166) t0__5a0 ! t0__8t0_a0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x167) t0__5a0 ! t0__8t0_a0 ! b_e_2t0a0 ! t0__2t0_a0 -LSYM(x168) t0__5a0 ! t0__4t0_a0 ! b_e_shift ! r__r_8t0 -LSYM(x169) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x170) t0__32a0 ! t0__t0_2a0 ! b_e_t0 ! t0__5t0 -LSYM(x171) t0__9a0 ! t0__2t0_a0 ! b_e_t0 ! t0__9t0 -LSYM(x172) t0__5a0 ! t0__4t0_a0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x173) t0__9a0 ! t0__2t0_a0 ! b_e_t02a0 ! t0__9t0 -LSYM(x174) t0__32a0 ! t0__t0_2a0 ! b_e_t04a0 ! t0__5t0 -LSYM(x175) t0__8a0 ! t0__2t0_a0 ! b_e_5t0 ! t0__2t0_a0 -LSYM(x176) t0__5a0 ! t0__4t0_a0 ! b_e_8t0 ! t0__t0_a0 -LSYM(x177) t0__5a0 ! t0__4t0_a0 ! b_e_8t0a0 ! t0__t0_a0 -LSYM(x178) t0__5a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__8t0_a0 -LSYM(x179) t0__5a0 ! t0__2t0_a0 ! b_e_2t0a0 ! t0__8t0_a0 -LSYM(x180) t0__9a0 ! t0__5t0 ! b_e_shift ! r__r_4t0 -LSYM(x181) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x182) t0__9a0 ! t0__5t0 ! b_e_2t0 ! t0__2t0_a0 -LSYM(x183) t0__9a0 ! t0__5t0 ! b_e_2t0a0 ! t0__2t0_a0 -LSYM(x184) t0__5a0 ! t0__9t0 ! b_e_4t0 ! t0__t0_a0 -LSYM(x185) t0__9a0 ! t0__4t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x186) t0__32a0 ! t0__t0ma0 ! b_e_2t0 ! t0__3t0 -LSYM(x187) t0__9a0 ! t0__4t0_a0 ! b_e_t02a0 ! t0__5t0 -LSYM(x188) t0__9a0 ! t0__5t0 ! b_e_4t0 ! t0__t0_2a0 -LSYM(x189) t0__5a0 ! t0__4t0_a0 ! b_e_t0 ! t0__9t0 -LSYM(x190) t0__9a0 ! t0__2t0_a0 ! b_e_2t0 ! t0__5t0 -LSYM(x191) t0__64a0 ! t0__3t0 ! b_e_t0 ! t0__t0ma0 -LSYM(x192) t0__8a0 ! t0__3t0 ! b_e_shift ! r__r_8t0 -LSYM(x193) t0__8a0 ! t0__3t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x194) t0__8a0 ! t0__3t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x195) t0__8a0 ! t0__8t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x196) t0__8a0 ! t0__3t0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x197) t0__8a0 ! t0__3t0 ! b_e_4t0a0 ! t0__2t0_a0 -LSYM(x198) t0__64a0 ! t0__t0_2a0 ! b_e_t0 ! t0__3t0 -LSYM(x199) t0__8a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x200) t0__5a0 ! t0__5t0 ! b_e_shift ! r__r_8t0 -LSYM(x201) t0__5a0 ! t0__5t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x202) t0__5a0 ! t0__5t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x203) t0__5a0 ! t0__5t0 ! b_e_2t0a0 ! t0__4t0_a0 -LSYM(x204) t0__8a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__3t0 -LSYM(x205) t0__5a0 ! t0__8t0_a0 ! b_e_t0 ! t0__5t0 -LSYM(x206) t0__64a0 ! t0__t0_4a0 ! b_e_t02a0 ! t0__3t0 -LSYM(x207) t0__8a0 ! t0__2t0_a0 ! b_e_3t0 ! t0__4t0_a0 -LSYM(x208) t0__5a0 ! t0__5t0 ! b_e_8t0 ! t0__t0_a0 -LSYM(x209) t0__5a0 ! t0__5t0 ! b_e_8t0a0 ! t0__t0_a0 -LSYM(x210) t0__5a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__5t0 -LSYM(x211) t0__5a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__5t0 -LSYM(x212) t0__3a0 ! t0__4t0_a0 ! b_e_4t0 ! t0__4t0_a0 -LSYM(x213) t0__3a0 ! t0__4t0_a0 ! b_e_4t0a0 ! t0__4t0_a0 -LSYM(x214) t0__9a0 ! t0__t0_4a0 ! b_e_2t04a0 ! t0__8t0_a0 -LSYM(x215) t0__5a0 ! t0__4t0_a0 ! b_e_5t0 ! t0__2t0_a0 -LSYM(x216) t0__9a0 ! t0__3t0 ! b_e_shift ! r__r_8t0 -LSYM(x217) t0__9a0 ! t0__3t0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x218) t0__9a0 ! t0__3t0 ! b_e_2t0 ! t0__4t0_a0 -LSYM(x219) t0__9a0 ! t0__8t0_a0 ! b_e_t0 ! t0__3t0 -LSYM(x220) t0__3a0 ! t0__9t0 ! b_e_4t0 ! t0__2t0_a0 -LSYM(x221) t0__3a0 ! t0__9t0 ! b_e_4t0a0 ! t0__2t0_a0 -LSYM(x222) t0__9a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__3t0 -LSYM(x223) t0__9a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x224) t0__9a0 ! t0__3t0 ! b_e_8t0 ! t0__t0_a0 -LSYM(x225) t0__9a0 ! t0__5t0 ! b_e_t0 ! t0__5t0 -LSYM(x226) t0__3a0 ! t0__2t0_a0 ! b_e_t02a0 ! t0__32t0 -LSYM(x227) t0__9a0 ! t0__5t0 ! b_e_t02a0 ! t0__5t0 -LSYM(x228) t0__9a0 ! t0__2t0_a0 ! b_e_4t0 ! t0__3t0 -LSYM(x229) t0__9a0 ! t0__2t0_a0 ! b_e_4t0a0 ! t0__3t0 -LSYM(x230) t0__9a0 ! t0__5t0 ! b_e_5t0 ! t0__t0_a0 -LSYM(x231) t0__9a0 ! t0__2t0_a0 ! b_e_3t0 ! t0__4t0_a0 -LSYM(x232) t0__3a0 ! t0__2t0_a0 ! b_e_8t0 ! t0__4t0_a0 -LSYM(x233) t0__3a0 ! t0__2t0_a0 ! b_e_8t0a0 ! t0__4t0_a0 -LSYM(x234) t0__3a0 ! t0__4t0_a0 ! b_e_2t0 ! t0__9t0 -LSYM(x235) t0__3a0 ! t0__4t0_a0 ! b_e_2t0a0 ! t0__9t0 -LSYM(x236) t0__9a0 ! t0__2t0_a0 ! b_e_4t08a0 ! t0__3t0 -LSYM(x237) t0__16a0 ! t0__5t0 ! b_e_3t0 ! t0__t0ma0 -LSYM(x238) t0__3a0 ! t0__4t0_a0 ! b_e_2t04a0 ! t0__9t0 -LSYM(x239) t0__16a0 ! t0__5t0 ! b_e_t0ma0 ! t0__3t0 -LSYM(x240) t0__9a0 ! t0__t0_a0 ! b_e_8t0 ! t0__3t0 -LSYM(x241) t0__9a0 ! t0__t0_a0 ! b_e_8t0a0 ! t0__3t0 -LSYM(x242) t0__5a0 ! t0__3t0 ! b_e_2t0 ! t0__8t0_a0 -LSYM(x243) t0__9a0 ! t0__9t0 ! b_e_t0 ! t0__3t0 -LSYM(x244) t0__5a0 ! t0__3t0 ! b_e_4t0 ! t0__4t0_a0 -LSYM(x245) t0__8a0 ! t0__3t0 ! b_e_5t0 ! t0__2t0_a0 -LSYM(x246) t0__5a0 ! t0__8t0_a0 ! b_e_2t0 ! t0__3t0 -LSYM(x247) t0__5a0 ! t0__8t0_a0 ! b_e_2t0a0 ! t0__3t0 -LSYM(x248) t0__32a0 ! t0__t0ma0 ! b_e_shift ! r__r_8t0 -LSYM(x249) t0__32a0 ! t0__t0ma0 ! b_e_t0 ! t0__8t0_a0 -LSYM(x250) t0__5a0 ! t0__5t0 ! b_e_2t0 ! t0__5t0 -LSYM(x251) t0__5a0 ! t0__5t0 ! b_e_2t0a0 ! t0__5t0 -LSYM(x252) t0__64a0 ! t0__t0ma0 ! b_e_shift ! r__r_4t0 -LSYM(x253) t0__64a0 ! t0__t0ma0 ! b_e_t0 ! t0__4t0_a0 -LSYM(x254) t0__128a0 ! t0__t0ma0 ! b_e_shift ! r__r_2t0 -LSYM(x255) t0__256a0 ! a1_ne_0_b_l0 ! t0__t0ma0 ! b_n_ret_t0 -/*1040 insts before this. */ -LSYM(ret_t0) MILLIRET -LSYM(e_t0) r__r_t0 -LSYM(e_shift) a1_ne_0_b_l2 - a0__256a0 /* a0 <<= 8 *********** */ - MILLIRETN -LSYM(e_t0ma0) a1_ne_0_b_l0 - t0__t0ma0 - MILLIRET - r__r_t0 -LSYM(e_t0a0) a1_ne_0_b_l0 - t0__t0_a0 - MILLIRET - r__r_t0 -LSYM(e_t02a0) a1_ne_0_b_l0 - t0__t0_2a0 - MILLIRET - r__r_t0 -LSYM(e_t04a0) a1_ne_0_b_l0 - t0__t0_4a0 - MILLIRET - r__r_t0 -LSYM(e_2t0) a1_ne_0_b_l1 - r__r_2t0 - MILLIRETN -LSYM(e_2t0a0) a1_ne_0_b_l0 - t0__2t0_a0 - MILLIRET - r__r_t0 -LSYM(e2t04a0) t0__t0_2a0 - a1_ne_0_b_l1 - r__r_2t0 - MILLIRETN -LSYM(e_3t0) a1_ne_0_b_l0 - t0__3t0 - MILLIRET - r__r_t0 -LSYM(e_4t0) a1_ne_0_b_l1 - r__r_4t0 - MILLIRETN -LSYM(e_4t0a0) a1_ne_0_b_l0 - t0__4t0_a0 - MILLIRET - r__r_t0 -LSYM(e4t08a0) t0__t0_2a0 - a1_ne_0_b_l1 - r__r_4t0 - MILLIRETN -LSYM(e_5t0) a1_ne_0_b_l0 - t0__5t0 - MILLIRET - r__r_t0 -LSYM(e_8t0) a1_ne_0_b_l1 - r__r_8t0 - MILLIRETN -LSYM(e_8t0a0) a1_ne_0_b_l0 - t0__8t0_a0 - MILLIRET - r__r_t0 - - .procend - .end -#endif diff --git a/arch/parisc/lib/milli/remI.S b/arch/parisc/lib/milli/remI.S deleted file mode 100644 index 63bc094471e2..000000000000 --- a/arch/parisc/lib/milli/remI.S +++ /dev/null @@ -1,185 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#include "milli.h" - -#ifdef L_remI -/* ROUTINE: $$remI - - DESCRIPTION: - . $$remI returns the remainder of the division of two signed 32-bit - . integers. The sign of the remainder is the same as the sign of - . the dividend. - - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = destroyed - . arg1 = destroyed - . ret1 = remainder - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: DIVIDE BY ZERO - . Changes memory at the following places: NONE - - PERMISSIBLE CONTEXT: - . Unwindable - . Does not create a stack frame - . Is usable for internal or external microcode - - DISCUSSION: - . Calls other millicode routines via mrp: NONE - . Calls other millicode routines: NONE */ - -RDEFINE(tmp,r1) -RDEFINE(retreg,ret1) - - SUBSPA_MILLI - ATTR_MILLI - .proc - .callinfo millicode - .entry -GSYM($$remI) -GSYM($$remoI) - .export $$remI,MILLICODE - .export $$remoI,MILLICODE - ldo -1(arg1),tmp /* is there at most one bit set ? */ - and,<> arg1,tmp,r0 /* if not, don't use power of 2 */ - addi,> 0,arg1,r0 /* if denominator > 0, use power */ - /* of 2 */ - b,n LREF(neg_denom) -LSYM(pow2) - comb,>,n 0,arg0,LREF(neg_num) /* is numerator < 0 ? */ - and arg0,tmp,retreg /* get the result */ - MILLIRETN -LSYM(neg_num) - subi 0,arg0,arg0 /* negate numerator */ - and arg0,tmp,retreg /* get the result */ - subi 0,retreg,retreg /* negate result */ - MILLIRETN -LSYM(neg_denom) - addi,< 0,arg1,r0 /* if arg1 >= 0, it's not power */ - /* of 2 */ - b,n LREF(regular_seq) - sub r0,arg1,tmp /* make denominator positive */ - comb,=,n arg1,tmp,LREF(regular_seq) /* test against 0x80000000 and 0 */ - ldo -1(tmp),retreg /* is there at most one bit set ? */ - and,= tmp,retreg,r0 /* if not, go to regular_seq */ - b,n LREF(regular_seq) - comb,>,n 0,arg0,LREF(neg_num_2) /* if arg0 < 0, negate it */ - and arg0,retreg,retreg - MILLIRETN -LSYM(neg_num_2) - subi 0,arg0,tmp /* test against 0x80000000 */ - and tmp,retreg,retreg - subi 0,retreg,retreg - MILLIRETN -LSYM(regular_seq) - addit,= 0,arg1,0 /* trap if div by zero */ - add,>= 0,arg0,retreg /* move dividend, if retreg < 0, */ - sub 0,retreg,retreg /* make it positive */ - sub 0,arg1, tmp /* clear carry, */ - /* negate the divisor */ - ds 0, tmp,0 /* set V-bit to the comple- */ - /* ment of the divisor sign */ - or 0,0, tmp /* clear tmp */ - add retreg,retreg,retreg /* shift msb bit into carry */ - ds tmp,arg1, tmp /* 1st divide step, if no carry */ - /* out, msb of quotient = 0 */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ -LSYM(t1) - ds tmp,arg1, tmp /* 2nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 3rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 4th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 5th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 6th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 7th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 8th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 9th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 10th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 11th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 12th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 13th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 14th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 15th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 16th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 17th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 18th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 19th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 20th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 21st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 22nd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 23rd divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 24th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 25th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 26th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 27th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 28th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 29th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 30th divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 31st divide step */ - addc retreg,retreg,retreg /* shift retreg with/into carry */ - ds tmp,arg1, tmp /* 32nd divide step, */ - addc retreg,retreg,retreg /* shift last bit into retreg */ - movb,>=,n tmp,retreg,LREF(finish) /* branch if pos. tmp */ - add,< arg1,0,0 /* if arg1 > 0, add arg1 */ - add,tr tmp,arg1,retreg /* for correcting remainder tmp */ - sub tmp,arg1,retreg /* else add absolute value arg1 */ -LSYM(finish) - add,>= arg0,0,0 /* set sign of remainder */ - sub 0,retreg,retreg /* to sign of dividend */ - MILLIRET - nop - .exit - .procend -#ifdef milliext - .origin 0x00000200 -#endif - .end -#endif diff --git a/arch/parisc/lib/milli/remU.S b/arch/parisc/lib/milli/remU.S deleted file mode 100644 index c0a2d6e247c3..000000000000 --- a/arch/parisc/lib/milli/remU.S +++ /dev/null @@ -1,148 +0,0 @@ -/* 32 and 64-bit millicode, original author Hewlett-Packard - adapted for gcc by Paul Bame <bame@debian.org> - and Alan Modra <alan@linuxcare.com.au>. - - Copyright 2001, 2002, 2003 Free Software Foundation, Inc. - - This file is part of GCC and is released under the terms of - of the GNU General Public License as published by the Free Software - Foundation; either version 2, or (at your option) any later version. - See the file COPYING in the top-level GCC source directory for a copy - of the license. */ - -#include "milli.h" - -#ifdef L_remU -/* ROUTINE: $$remU - . Single precision divide for remainder with unsigned binary integers. - . - . The remainder must be dividend-(dividend/divisor)*divisor. - . Divide by zero is trapped. - - INPUT REGISTERS: - . arg0 == dividend - . arg1 == divisor - . mrp == return pc - . sr0 == return space when called externally - - OUTPUT REGISTERS: - . arg0 = undefined - . arg1 = undefined - . ret1 = remainder - - OTHER REGISTERS AFFECTED: - . r1 = undefined - - SIDE EFFECTS: - . Causes a trap under the following conditions: DIVIDE BY ZERO - . Changes memory at the following places: NONE - - PERMISSIBLE CONTEXT: - . Unwindable. - . Does not create a stack frame. - . Suitable for internal or external millicode. - . Assumes the special millicode register conventions. - - DISCUSSION: - . Calls other millicode routines using mrp: NONE - . Calls other millicode routines: NONE */ - - -RDEFINE(temp,r1) -RDEFINE(rmndr,ret1) /* r29 */ - SUBSPA_MILLI - ATTR_MILLI - .export $$remU,millicode - .proc - .callinfo millicode - .entry -GSYM($$remU) - ldo -1(arg1),temp /* is there at most one bit set ? */ - and,= arg1,temp,r0 /* if not, don't use power of 2 */ - b LREF(regular_seq) - addit,= 0,arg1,r0 /* trap on div by zero */ - and arg0,temp,rmndr /* get the result for power of 2 */ - MILLIRETN -LSYM(regular_seq) - comib,>=,n 0,arg1,LREF(special_case) - subi 0,arg1,rmndr /* clear carry, negate the divisor */ - ds r0,rmndr,r0 /* set V-bit to 1 */ - add arg0,arg0,temp /* shift msb bit into carry */ - ds r0,arg1,rmndr /* 1st divide step, if no carry */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 2nd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 3rd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 4th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 5th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 6th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 7th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 8th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 9th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 10th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 11th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 12th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 13th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 14th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 15th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 16th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 17th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 18th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 19th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 20th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 21st divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 22nd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 23rd divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 24th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 25th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 26th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 27th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 28th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 29th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 30th divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 31st divide step */ - addc temp,temp,temp /* shift temp with/into carry */ - ds rmndr,arg1,rmndr /* 32nd divide step, */ - comiclr,<= 0,rmndr,r0 - add rmndr,arg1,rmndr /* correction */ - MILLIRETN - nop - -/* Putting >= on the last DS and deleting COMICLR does not work! */ -LSYM(special_case) - sub,>>= arg0,arg1,rmndr - copy arg0,rmndr - MILLIRETN - nop - .exit - .procend - .end -#endif diff --git a/arch/powerpc/boot/dts/sequoia.dts b/arch/powerpc/boot/dts/sequoia.dts index 8833dfe2e8b4..10784ff45dd6 100644 --- a/arch/powerpc/boot/dts/sequoia.dts +++ b/arch/powerpc/boot/dts/sequoia.dts @@ -245,6 +245,7 @@ device_type = "rgmii-interface"; compatible = "ibm,rgmii-440epx", "ibm,rgmii"; reg = <ef601000 8>; + has-mdio; }; EMAC0: ethernet@ef600e00 { @@ -273,6 +274,8 @@ zmii-channel = <0>; rgmii-device = <&RGMII0>; rgmii-channel = <0>; + has-inverted-stacr-oc; + has-new-stacr-staopc; }; EMAC1: ethernet@ef600f00 { @@ -301,6 +304,8 @@ zmii-channel = <1>; rgmii-device = <&RGMII0>; rgmii-channel = <1>; + has-inverted-stacr-oc; + has-new-stacr-staopc; }; }; }; diff --git a/arch/powerpc/configs/bamboo_defconfig b/arch/powerpc/configs/bamboo_defconfig index 844808ebf245..76d883e008b6 100644 --- a/arch/powerpc/configs/bamboo_defconfig +++ b/arch/powerpc/configs/bamboo_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23 -# Fri Oct 19 09:01:11 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:04 2007 # # CONFIG_PPC64 is not set @@ -69,11 +69,14 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set CONFIG_FAIR_GROUP_SCHED=y CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -209,6 +212,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -287,10 +291,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -690,16 +690,16 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y # CONFIG_PROFILING is not set +# CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -723,10 +723,12 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set diff --git a/arch/powerpc/configs/cell_defconfig b/arch/powerpc/configs/cell_defconfig index dcd7c02727c2..f3bde8c6c8c6 100644 --- a/arch/powerpc/configs/cell_defconfig +++ b/arch/powerpc/configs/cell_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc3 -# Wed Aug 22 15:19:19 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:05 2007 # CONFIG_PPC64=y @@ -11,6 +11,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY is not set CONFIG_POWER3=y CONFIG_POWER4=y +CONFIG_TUNE_CELL=y CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y @@ -19,8 +20,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=4 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -64,13 +70,21 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=15 CONFIG_CGROUPS=y +# CONFIG_CGROUP_DEBUG is not set +# CONFIG_CGROUP_NS is not set CONFIG_CPUSETS=y +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set +# CONFIG_CGROUP_CPUACCT is not set CONFIG_SYSFS_DEPRECATED=y +CONFIG_PROC_PID_CPUSET=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" @@ -90,7 +104,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -111,6 +124,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_BLK_DEV_BSG is not set +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -129,7 +143,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -195,6 +208,8 @@ CONFIG_CPU_FREQ_STAT=y # CONFIG_CPU_FREQ_STAT_DETAILS is not set CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set CONFIG_CPU_FREQ_GOV_PERFORMANCE=y CONFIG_CPU_FREQ_GOV_POWERSAVE=y CONFIG_CPU_FREQ_GOV_USERSPACE=y @@ -211,6 +226,10 @@ CONFIG_AXON_RAM=m # # Kernel options # +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -223,6 +242,7 @@ CONFIG_PREEMPT_BKL=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m CONFIG_FORCE_MAX_ZONEORDER=9 +CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y # CONFIG_IOMMU_VMERGE is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y # CONFIG_KEXEC is not set @@ -243,6 +263,8 @@ CONFIG_NEED_MULTIPLE_NODES=y CONFIG_HAVE_MEMORY_PRESENT=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPARSEMEM_EXTREME=y +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y +CONFIG_SPARSEMEM_VMEMMAP=y CONFIG_MEMORY_HOTPLUG=y CONFIG_MEMORY_HOTPLUG_SPARSE=y CONFIG_SPLIT_PTLOCK_CPUS=4 @@ -275,11 +297,8 @@ CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set CONFIG_KERNEL_START=0xc000000000000000 @@ -321,6 +340,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y # CONFIG_INET_XFRM_MODE_BEET is not set +CONFIG_INET_LRO=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -382,6 +402,7 @@ CONFIG_NETFILTER_XT_MATCH_SCTP=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m +CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m @@ -430,10 +451,6 @@ CONFIG_IP_NF_ARP_MANGLE=m # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set CONFIG_NET_CLS_ROUTE=y @@ -463,6 +480,7 @@ CONFIG_NET_CLS_ROUTE=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -515,6 +533,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -522,8 +545,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set CONFIG_BLK_DEV_AEC62XX=y # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set @@ -552,7 +573,7 @@ CONFIG_BLK_DEV_SIIMAGE=y CONFIG_BLK_DEV_CELLEB=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -593,6 +614,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_ISCSI_ATTRS is not set CONFIG_SCSI_SAS_ATTRS=y # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -668,6 +690,7 @@ CONFIG_SATA_PROMISE=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -699,11 +722,9 @@ CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m # CONFIG_DM_MULTIPATH_EMC is not set # CONFIG_DM_MULTIPATH_RDAC is not set +# CONFIG_DM_MULTIPATH_HP is not set # CONFIG_DM_DELAY is not set - -# -# Fusion MPT device support -# +# CONFIG_DM_UEVENT is not set CONFIG_FUSION=y # CONFIG_FUSION_SPI is not set # CONFIG_FUSION_FC is not set @@ -726,6 +747,8 @@ CONFIG_BONDING=m CONFIG_MACVLAN=m # CONFIG_EQUALIZER is not set CONFIG_TUN=y +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -736,21 +759,30 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC is not set +CONFIG_IBM_NEW_EMAC_ZMII=y +CONFIG_IBM_NEW_EMAC_RGMII=y +CONFIG_IBM_NEW_EMAC_TAH=y +CONFIG_IBM_NEW_EMAC_EMAC4=y # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=m CONFIG_E1000_NAPI=y # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set CONFIG_SKGE=m +# CONFIG_SKGE_DEBUG is not set CONFIG_SKY2=m # CONFIG_SKY2_DEBUG is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=y # CONFIG_BNX2 is not set @@ -761,12 +793,15 @@ CONFIG_GELIC_NET=m CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_PASEMI_MAC is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -782,7 +817,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -812,7 +846,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -893,32 +926,11 @@ CONFIG_IPMI_DEVICE_INTERFACE=m CONFIG_IPMI_SI=m CONFIG_IPMI_WATCHDOG=m CONFIG_IPMI_POWEROFF=m -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -# CONFIG_WATCHDOG_RTAS is not set - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set - -# -# USB-based Watchdog Cards -# -# CONFIG_USBPCWATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_HANGCHECK_TIMER is not set # CONFIG_TCG_TPM is not set @@ -986,6 +998,31 @@ CONFIG_I2C_ALGOBIT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_WATCHDOG_RTAS is not set + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -1002,16 +1039,17 @@ CONFIG_I2C_ALGOBIT=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -1026,6 +1064,7 @@ CONFIG_DUMMY_CONSOLE=y CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1175,19 +1214,6 @@ CONFIG_EDAC_MM_EDAC=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # CONFIG_UIO=m @@ -1253,7 +1279,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1272,10 +1297,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1288,6 +1310,7 @@ CONFIG_LOCKD_V4=y CONFIG_NFS_ACL_SUPPORT=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y +CONFIG_SUNRPC_XPRT_RDMA=m # CONFIG_SUNRPC_BIND34 is not set # CONFIG_RPCSEC_GSS_KRB5 is not set # CONFIG_RPCSEC_GSS_SPKM3 is not set @@ -1318,10 +1341,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set CONFIG_EFI_PARTITION=y # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=m CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1362,10 +1381,6 @@ CONFIG_NLS_ISO8859_15=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1389,19 +1404,17 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y CONFIG_PROFILING=y CONFIG_OPROFILE=m -CONFIG_OPROFILE_CELL=y # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y # CONFIG_ENABLE_MUST_CHECK is not set CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1425,9 +1438,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set # CONFIG_FORCED_INLINING is not set +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1436,6 +1452,7 @@ CONFIG_XMON=y CONFIG_XMON_DEFAULT=y CONFIG_XMON_DISASSEMBLY=y CONFIG_IRQSTACKS=y +# CONFIG_VIRQ_DEBUG is not set # CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set @@ -1444,6 +1461,7 @@ CONFIG_IRQSTACKS=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=m @@ -1464,6 +1482,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=m CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=m # CONFIG_CRYPTO_FCRYPT is not set @@ -1477,9 +1496,12 @@ CONFIG_CRYPTO_DES=m # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_DEFLATE=m # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/celleb_defconfig b/arch/powerpc/configs/celleb_defconfig index 2c5969801bd6..421e08ee857a 100644 --- a/arch/powerpc/configs/celleb_defconfig +++ b/arch/powerpc/configs/celleb_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:32:07 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:07 2007 # CONFIG_PPC64=y @@ -11,6 +11,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY is not set CONFIG_POWER3=y CONFIG_POWER4=y +CONFIG_TUNE_CELL=y CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y @@ -19,8 +20,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=4 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,11 +69,13 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=15 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -88,7 +96,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -109,6 +116,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set CONFIG_BLK_DEV_BSG=y +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -127,7 +135,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -160,8 +167,8 @@ CONFIG_PPC_UDBG_BEAT=y # CONFIG_MMIO_NVRAM is not set # CONFIG_PPC_MPC106 is not set # CONFIG_PPC_970_NAP is not set -# CONFIG_PPC_INDIRECT_IO is not set -# CONFIG_GENERIC_IOMAP is not set +CONFIG_PPC_INDIRECT_IO=y +CONFIG_GENERIC_IOMAP=y # CONFIG_CPU_FREQ is not set # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set @@ -169,6 +176,10 @@ CONFIG_PPC_UDBG_BEAT=y # # Kernel options # +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -181,6 +192,7 @@ CONFIG_PREEMPT_BKL=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m CONFIG_FORCE_MAX_ZONEORDER=13 +CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y # CONFIG_IOMMU_VMERGE is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_KEXEC=y @@ -200,6 +212,8 @@ CONFIG_NEED_MULTIPLE_NODES=y CONFIG_HAVE_MEMORY_PRESENT=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPARSEMEM_EXTREME=y +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y +CONFIG_SPARSEMEM_VMEMMAP=y CONFIG_MEMORY_HOTPLUG=y CONFIG_MEMORY_HOTPLUG_SPARSE=y CONFIG_SPLIT_PTLOCK_CPUS=4 @@ -231,11 +245,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set CONFIG_KERNEL_START=0xc000000000000000 @@ -274,6 +285,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_LRO=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -336,10 +348,6 @@ CONFIG_IP_NF_QUEUE=m # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -368,6 +376,7 @@ CONFIG_IP_NF_QUEUE=m # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -420,6 +429,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -427,8 +441,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set @@ -457,7 +469,7 @@ CONFIG_BLK_DEV_IDEDMA_PCI=y CONFIG_BLK_DEV_CELLEB=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -498,6 +510,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -549,15 +562,10 @@ CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m # CONFIG_DM_MULTIPATH_EMC is not set # CONFIG_DM_MULTIPATH_RDAC is not set +# CONFIG_DM_MULTIPATH_HP is not set # CONFIG_DM_DELAY is not set - -# -# Fusion MPT device support -# +# CONFIG_DM_UEVENT is not set # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -573,6 +581,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -583,11 +593,17 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -595,6 +611,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -604,12 +621,15 @@ CONFIG_SPIDER_NET=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_PASEMI_MAC is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -625,7 +645,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -655,7 +674,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -725,31 +743,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_HVC_DRIVER=y CONFIG_HVC_BEAT=y # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set - -# -# USB-based Watchdog Cards -# -# CONFIG_USBPCWATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_HANGCHECK_TIMER is not set # CONFIG_TCG_TPM is not set @@ -817,6 +815,30 @@ CONFIG_I2C_ALGOBIT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -833,16 +855,17 @@ CONFIG_I2C_ALGOBIT=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -857,6 +880,7 @@ CONFIG_DUMMY_CONSOLE=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -980,19 +1004,6 @@ CONFIG_USB_MON=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1060,7 +1071,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1079,10 +1089,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=m CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1130,10 +1137,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set CONFIG_EFI_PARTITION=y # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=m CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1174,10 +1177,6 @@ CONFIG_NLS_ISO8859_15=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1197,17 +1196,16 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y # CONFIG_PROFILING is not set # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1231,9 +1229,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set # CONFIG_FORCED_INLINING is not set +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1242,6 +1243,7 @@ CONFIG_XMON=y CONFIG_XMON_DEFAULT=y CONFIG_XMON_DISASSEMBLY=y CONFIG_IRQSTACKS=y +# CONFIG_VIRQ_DEBUG is not set # CONFIG_BOOTX_TEXT is not set CONFIG_PPC_EARLY_DEBUG=y # CONFIG_PPC_EARLY_DEBUG_LPAR is not set @@ -1253,12 +1255,14 @@ CONFIG_PPC_EARLY_DEBUG=y # CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set CONFIG_PPC_EARLY_DEBUG_BEAT=y # CONFIG_PPC_EARLY_DEBUG_44x is not set +# CONFIG_PPC_EARLY_DEBUG_CPM is not set # # Security options # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=m @@ -1279,6 +1283,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=m CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=m # CONFIG_CRYPTO_FCRYPT is not set @@ -1293,9 +1298,12 @@ CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m +# CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CAMELLIA is not set CONFIG_CRYPTO_TEST=m +# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/chrp32_defconfig b/arch/powerpc/configs/chrp32_defconfig index 6f27e57331d5..5989b5d2277e 100644 --- a/arch/powerpc/configs/chrp32_defconfig +++ b/arch/powerpc/configs/chrp32_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:33:50 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:09 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_PPC_STD_MMU_32=y CONFIG_SMP=y CONFIG_NR_CPUS=4 CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,11 +68,13 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=15 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -88,7 +95,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -129,7 +135,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -165,6 +170,10 @@ CONFIG_PPC_MPC106=y # Kernel options # CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -188,6 +197,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -213,11 +223,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -232,7 +239,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -265,6 +272,7 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -327,6 +335,7 @@ CONFIG_NETFILTER_XTABLES=m # CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set # CONFIG_NETFILTER_XT_MATCH_STRING is not set # CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set +# CONFIG_NETFILTER_XT_MATCH_TIME is not set # CONFIG_NETFILTER_XT_MATCH_U32 is not set # CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set @@ -380,10 +389,6 @@ CONFIG_NF_NAT_SIP=m # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -412,6 +417,7 @@ CONFIG_NF_NAT_SIP=m # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" # CONFIG_STANDALONE is not set CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -467,6 +473,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -474,8 +485,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set @@ -502,9 +511,22 @@ CONFIG_BLK_DEV_SL82C105=y CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_BLK_DEV_TC86C001 is not set # CONFIG_IDE_ARM is not set -# CONFIG_IDE_CHIPSETS is not set + +# +# Other IDE chipsets support +# + +# +# Note: most of these also require special kernel boot parameters +# +# CONFIG_BLK_DEV_4DRIVES is not set +# CONFIG_BLK_DEV_ALI14XX is not set +# CONFIG_BLK_DEV_DTC2278 is not set +# CONFIG_BLK_DEV_HT6560B is not set +# CONFIG_BLK_DEV_QD65XX is not set +# CONFIG_BLK_DEV_UMC8672 is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -544,6 +566,7 @@ CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -558,6 +581,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_IN2000 is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set @@ -599,14 +623,7 @@ CONFIG_SCSI_SYM53C8XX_MMIO=y # CONFIG_SCSI_SRP is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -622,6 +639,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -644,6 +663,10 @@ CONFIG_DE4X5=y # CONFIG_DEPCA is not set # CONFIG_HP100 is not set # CONFIG_NET_ISA is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y CONFIG_PCNET32=y # CONFIG_PCNET32_NAPI is not set @@ -654,7 +677,6 @@ CONFIG_PCNET32=y # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set # CONFIG_CS89x0 is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set @@ -678,6 +700,7 @@ CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -685,6 +708,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -694,11 +718,14 @@ CONFIG_MV643XX_ETH=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -714,7 +741,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -754,7 +780,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set @@ -838,7 +863,6 @@ CONFIG_LEGACY_PTY_COUNT=256 CONFIG_BRIQ_PANEL=m # CONFIG_HVC_RTAS is not set # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_NVRAM=y CONFIG_GEN_RTC=y @@ -846,8 +870,6 @@ CONFIG_GEN_RTC=y # CONFIG_DTLK is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -918,6 +940,13 @@ CONFIG_I2C_ALGOBIT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -934,18 +963,8 @@ CONFIG_I2C_ALGOBIT=y # # Graphics support # -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_LCD_CLASS_DEVICE=m -CONFIG_BACKLIGHT_CLASS_DEVICE=y - -# -# Display device support -# -CONFIG_DISPLAY_SUPPORT=m - -# -# Display hardware drivers -# +# CONFIG_AGP is not set +# CONFIG_DRM is not set # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y @@ -954,6 +973,7 @@ CONFIG_FB_DDC=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set @@ -1009,6 +1029,19 @@ CONFIG_FB_3DFX=y # CONFIG_FB_PM3 is not set # CONFIG_FB_IBM_GXT4500 is not set # CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set + +# +# Display device support +# +CONFIG_DISPLAY_SUPPORT=m + +# +# Display hardware drivers +# # # Console display driver support @@ -1035,6 +1068,7 @@ CONFIG_LOGO_LINUX_CLUT224=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1158,19 +1192,6 @@ CONFIG_USB_MON=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1187,7 +1208,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1233,7 +1253,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1252,10 +1271,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y # CONFIG_NFS_FS is not set # CONFIG_NFSD is not set # CONFIG_SMB_FS is not set @@ -1285,10 +1301,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1329,10 +1341,6 @@ CONFIG_NLS_ISO8859_1=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1352,17 +1360,16 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y # CONFIG_PROFILING is not set # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1387,9 +1394,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1406,6 +1416,7 @@ CONFIG_XMON_DISASSEMBLY=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=m CONFIG_CRYPTO_BLKCIPHER=m @@ -1425,6 +1436,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=m CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set # CONFIG_CRYPTO_DES is not set # CONFIG_CRYPTO_FCRYPT is not set @@ -1438,9 +1450,12 @@ CONFIG_CRYPTO_PCBC=m CONFIG_CRYPTO_ARC4=m # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/ebony_defconfig b/arch/powerpc/configs/ebony_defconfig index d3ef642811ef..b84298ce42be 100644 --- a/arch/powerpc/configs/ebony_defconfig +++ b/arch/powerpc/configs/ebony_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23 -# Thu Oct 18 08:01:57 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:11 2007 # # CONFIG_PPC64 is not set @@ -43,7 +43,7 @@ CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y CONFIG_ARCH_MAY_HAVE_PC_FDC=y CONFIG_PPC_OF=y CONFIG_OF=y -# CONFIG_PPC_UDBG_16550 is not set +CONFIG_PPC_UDBG_16550=y # CONFIG_GENERIC_TBSYNC is not set CONFIG_AUDIT_ARCH=y CONFIG_GENERIC_BUG=y @@ -68,11 +68,14 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set CONFIG_FAIR_GROUP_SCHED=y CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -206,6 +209,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -284,10 +288,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -568,7 +568,6 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set @@ -587,6 +586,7 @@ CONFIG_DEVPORT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set # # Sonics Silicon Backplane @@ -772,16 +772,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -805,10 +802,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set diff --git a/arch/powerpc/configs/ep88xc_defconfig b/arch/powerpc/configs/ep88xc_defconfig index d8ee3c0dcadf..a1f98200d9e3 100644 --- a/arch/powerpc/configs/ep88xc_defconfig +++ b/arch/powerpc/configs/ep88xc_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc6 -# Fri Sep 14 14:59:56 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:13 2007 # # CONFIG_PPC64 is not set @@ -18,8 +18,13 @@ CONFIG_8xx=y # CONFIG_PPC_MM_SLICES is not set CONFIG_NOT_COHERENT_CACHE=y CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -59,9 +64,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set # CONFIG_BLK_DEV_INITRD is not set @@ -81,7 +89,6 @@ CONFIG_BUG=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y # CONFIG_VM_EVENT_COUNTERS is not set @@ -158,6 +165,10 @@ CONFIG_CPM=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y CONFIG_HZ_100=y # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set @@ -169,6 +180,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set # CONFIG_MATH_EMULATION is not set +CONFIG_8XX_MINIMAL_FPEMU=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y @@ -179,6 +191,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -204,10 +217,6 @@ CONFIG_FSL_SOC=y # CONFIG_PCI_SYSCALL is not set # CONFIG_PCI_QSPAN is not set # CONFIG_ARCH_SUPPORTS_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # @@ -259,6 +268,7 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -284,10 +294,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -316,6 +322,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -339,6 +346,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -418,6 +426,7 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set CONFIG_PHYLIB=y # @@ -436,9 +445,15 @@ CONFIG_LXT_PHY=y # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FEC=y +CONFIG_FS_ENET_MDIO_FEC=y # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -496,7 +511,6 @@ CONFIG_SERIAL_CPM_SMC2=y CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y @@ -514,6 +528,13 @@ CONFIG_GEN_RTC=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -530,16 +551,15 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -552,19 +572,6 @@ CONFIG_DAB=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -613,7 +620,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -633,10 +639,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -678,15 +681,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -703,16 +698,13 @@ CONFIG_ZLIB_INFLATE=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -734,8 +726,11 @@ CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -748,4 +743,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/g5_defconfig b/arch/powerpc/configs/g5_defconfig index 0a6fa1fc9766..3673dd23120c 100644 --- a/arch/powerpc/configs/g5_defconfig +++ b/arch/powerpc/configs/g5_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:34:59 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:15 2007 # CONFIG_PPC64=y @@ -10,6 +10,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY=y CONFIG_POWER4=y +# CONFIG_TUNE_CELL is not set CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y @@ -18,8 +19,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=4 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,11 +69,15 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=17 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -88,7 +98,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -109,6 +118,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set CONFIG_BLK_DEV_BSG=y +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -127,7 +137,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -164,6 +173,8 @@ CONFIG_CPU_FREQ_STAT=y # CONFIG_CPU_FREQ_STAT_DETAILS is not set CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set CONFIG_CPU_FREQ_GOV_PERFORMANCE=y CONFIG_CPU_FREQ_GOV_POWERSAVE=y CONFIG_CPU_FREQ_GOV_USERSPACE=y @@ -180,6 +191,10 @@ CONFIG_CPU_FREQ_PMAC64=y # # Kernel options # +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -192,6 +207,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_FORCE_MAX_ZONEORDER=13 +CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y CONFIG_IOMMU_VMERGE=y # CONFIG_HOTPLUG_CPU is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -210,6 +226,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y CONFIG_ZONE_DMA_FLAG=1 @@ -221,6 +238,7 @@ CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set CONFIG_SUSPEND_SMP_POSSIBLE=y +CONFIG_HIBERNATION_SMP_POSSIBLE=y CONFIG_SECCOMP=y # CONFIG_WANT_DEVICE_TREE is not set CONFIG_ISA_DMA_API=y @@ -237,11 +255,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_PCI_MSI=y +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set CONFIG_KERNEL_START=0xc000000000000000 @@ -281,6 +296,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_LRO=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -340,10 +356,6 @@ CONFIG_LLC=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -372,6 +384,7 @@ CONFIG_LLC=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -426,15 +439,17 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y # CONFIG_IDEPCI_SHARE_IRQ is not set CONFIG_IDEPCI_PCIBUS_ORDER=y -# CONFIG_BLK_DEV_OFFBOARD is not set # CONFIG_BLK_DEV_GENERIC is not set # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set @@ -465,7 +480,7 @@ CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y CONFIG_BLK_DEV_IDEDMA_PMAC=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -506,6 +521,7 @@ CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -581,6 +597,7 @@ CONFIG_SATA_SVW=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -610,14 +627,8 @@ CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m # CONFIG_DM_MULTIPATH is not set # CONFIG_DM_DELAY is not set - -# -# Fusion MPT device support -# +# CONFIG_DM_UEVENT is not set # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -664,6 +675,8 @@ CONFIG_BONDING=m # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -674,7 +687,12 @@ CONFIG_SUNGEM=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y CONFIG_ACENIC=y CONFIG_ACENIC_OMIT_TIGON_I=y @@ -682,6 +700,7 @@ CONFIG_ACENIC_OMIT_TIGON_I=y CONFIG_E1000=y # CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -689,6 +708,7 @@ CONFIG_E1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=y # CONFIG_BNX2 is not set @@ -697,12 +717,15 @@ CONFIG_TIGON3=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_PASEMI_MAC is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set CONFIG_TR=y CONFIG_IBMOL=y # CONFIG_3C359 is not set @@ -721,7 +744,6 @@ CONFIG_USB_CATC=m CONFIG_USB_KAWETH=m CONFIG_USB_PEGASUS=m CONFIG_USB_RTL8150=m -# CONFIG_USB_USBNET_MII is not set CONFIG_USB_USBNET=m # CONFIG_USB_NET_AX8817X is not set CONFIG_USB_NET_CDCETHER=m @@ -771,7 +793,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 CONFIG_INPUT_JOYDEV=m -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set @@ -828,15 +849,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -CONFIG_AGP=m -CONFIG_AGP_UNINORTH=m -# CONFIG_DRM is not set CONFIG_RAW_DRIVER=y CONFIG_MAX_RAW_DEVS=256 # CONFIG_HANGCHECK_TIMER is not set @@ -906,6 +923,13 @@ CONFIG_I2C_POWERMAC=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -923,14 +947,9 @@ CONFIG_DAB=y # # Graphics support # -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_LCD_CLASS_DEVICE=m -CONFIG_BACKLIGHT_CLASS_DEVICE=y - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set +CONFIG_AGP=m +CONFIG_AGP_UNINORTH=m +# CONFIG_DRM is not set CONFIG_VGASTATE=y CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_FB=y @@ -939,6 +958,7 @@ CONFIG_FB_DDC=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set @@ -986,6 +1006,15 @@ CONFIG_FB_RADEON_BACKLIGHT=y # CONFIG_FB_PM3 is not set # CONFIG_FB_IBM_GXT4500 is not set # CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support @@ -1143,6 +1172,7 @@ CONFIG_SND_USB_AUDIO=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1239,6 +1269,7 @@ CONFIG_USB_SERIAL_GENERIC=y # CONFIG_USB_SERIAL_AIRPRIME is not set # CONFIG_USB_SERIAL_ARK3116 is not set CONFIG_USB_SERIAL_BELKIN=m +# CONFIG_USB_SERIAL_CH341 is not set # CONFIG_USB_SERIAL_WHITEHEAT is not set CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m # CONFIG_USB_SERIAL_CP2101 is not set @@ -1326,19 +1357,6 @@ CONFIG_USB_APPLEDISPLAY=m # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1415,7 +1433,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1434,10 +1451,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1491,10 +1505,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -1535,10 +1545,6 @@ CONFIG_NLS_ISO8859_15=y # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=y - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1558,18 +1564,17 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y CONFIG_PROFILING=y CONFIG_OPROFILE=y # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1593,14 +1598,18 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set # CONFIG_DEBUGGER is not set CONFIG_IRQSTACKS=y +# CONFIG_VIRQ_DEBUG is not set CONFIG_BOOTX_TEXT=y # CONFIG_PPC_EARLY_DEBUG is not set @@ -1609,6 +1618,7 @@ CONFIG_BOOTX_TEXT=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1629,6 +1639,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1643,9 +1654,12 @@ CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m +# CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CAMELLIA is not set CONFIG_CRYPTO_TEST=m +# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/holly_defconfig b/arch/powerpc/configs/holly_defconfig index 11009185d230..a211a79959ca 100644 --- a/arch/powerpc/configs/holly_defconfig +++ b/arch/powerpc/configs/holly_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:35:41 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:17 2007 # # CONFIG_PPC64 is not set @@ -15,13 +15,19 @@ CONFIG_6xx=y # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_FPU=y +# CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -61,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -84,7 +93,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -122,16 +130,21 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # # Platform support # -# CONFIG_PPC_MULTIPLATFORM is not set -CONFIG_EMBEDDED6xx=y +CONFIG_PPC_MULTIPLATFORM=y # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set +CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set # CONFIG_PPC_MPC52xx is not set # CONFIG_PPC_MPC5200 is not set +# CONFIG_PPC_EFIKA is not set +# CONFIG_PPC_LITE5200 is not set +# CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PQ2ADS is not set +CONFIG_EMBEDDED6xx=y # CONFIG_LINKSTATION is not set # CONFIG_MPC7448HPC2 is not set CONFIG_PPC_HOLLY=y @@ -147,6 +160,7 @@ CONFIG_MPIC_WEIRD=y # CONFIG_PPC_INDIRECT_IO is not set # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set +# CONFIG_TAU is not set # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set @@ -154,6 +168,10 @@ CONFIG_MPIC_WEIRD=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -165,6 +183,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +# CONFIG_KEXEC is not set CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y @@ -174,6 +193,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -183,6 +203,8 @@ CONFIG_PROC_DEVICETREE=y CONFIG_CMDLINE_BOOL=y CONFIG_CMDLINE="console=ttyS0,115200" # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_SECCOMP is not set CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="holly.dts" @@ -200,11 +222,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -219,7 +238,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -259,6 +278,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -284,10 +304,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -316,6 +332,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -386,6 +403,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -397,6 +415,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -464,6 +483,7 @@ CONFIG_ATA=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -478,14 +498,7 @@ CONFIG_ATA=y # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -501,6 +514,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -517,6 +532,7 @@ CONFIG_PHYLIB=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -527,11 +543,17 @@ CONFIG_VORTEX=y # CONFIG_TYPHOON is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -539,20 +561,25 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set CONFIG_TSI108_ETH=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -585,7 +612,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -637,15 +663,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -660,9 +683,9 @@ CONFIG_DEVPORT=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set @@ -675,6 +698,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -691,16 +721,17 @@ CONFIG_HWMON=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -709,6 +740,7 @@ CONFIG_HWMON=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -730,19 +762,6 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -759,7 +778,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -800,7 +818,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -819,10 +836,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set @@ -862,15 +876,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -888,17 +894,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set -# CONFIG_KPROBES is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -922,9 +924,12 @@ CONFIG_DETECT_SOFTLOCKUP=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -933,6 +938,7 @@ CONFIG_XMON=y CONFIG_XMON_DEFAULT=y CONFIG_XMON_DISASSEMBLY=y # CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -940,4 +946,6 @@ CONFIG_XMON_DISASSEMBLY=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/iseries_defconfig b/arch/powerpc/configs/iseries_defconfig index d78e3a6fc68c..4a87745c7803 100644 --- a/arch/powerpc/configs/iseries_defconfig +++ b/arch/powerpc/configs/iseries_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:37:16 2007 +# Linux kernel version: 2.6.24-rc3 +# Wed Nov 21 11:19:59 2007 # CONFIG_PPC64=y @@ -11,6 +11,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY is not set CONFIG_POWER3=y CONFIG_POWER4=y +# CONFIG_TUNE_CELL is not set CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y @@ -19,8 +20,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=32 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,12 +69,17 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set CONFIG_AUDIT=y CONFIG_AUDITSYSCALL=y +CONFIG_AUDIT_TREE=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=17 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -89,7 +100,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -110,6 +120,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set CONFIG_BLK_DEV_BSG=y +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -128,7 +139,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -172,6 +182,10 @@ CONFIG_GENERIC_IOMAP=y # # Kernel options # +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -201,6 +215,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y CONFIG_ZONE_DMA_FLAG=1 @@ -227,11 +242,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set CONFIG_KERNEL_START=0xc000000000000000 @@ -271,6 +283,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=m +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -338,6 +351,7 @@ CONFIG_NETFILTER_XT_MATCH_SCTP=m # CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m +CONFIG_NETFILTER_XT_MATCH_TIME=m # CONFIG_NETFILTER_XT_MATCH_U32 is not set # CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set @@ -403,10 +417,6 @@ CONFIG_LLC=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set CONFIG_NET_CLS_ROUTE=y @@ -436,6 +446,7 @@ CONFIG_NET_CLS_ROUTE=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=m @@ -508,6 +519,7 @@ CONFIG_SCSI_FC_ATTRS=y CONFIG_SCSI_SAS_ATTRS=m CONFIG_SCSI_SAS_LIBSAS=m CONFIG_SCSI_SAS_LIBSAS_DEBUG=y +CONFIG_SCSI_SRP_ATTRS=m CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -559,14 +571,8 @@ CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m # CONFIG_DM_MULTIPATH is not set # CONFIG_DM_DELAY is not set - -# -# Fusion MPT device support -# +# CONFIG_DM_UEVENT is not set # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -582,6 +588,8 @@ CONFIG_BONDING=m # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -592,6 +600,10 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y CONFIG_PCNET32=y CONFIG_PCNET32_NAPI=y @@ -599,7 +611,6 @@ CONFIG_PCNET32_NAPI=y # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=y # CONFIG_FEALNX is not set @@ -619,6 +630,7 @@ CONFIG_ACENIC=m CONFIG_E1000=m # CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -626,6 +638,7 @@ CONFIG_E1000=m # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -634,12 +647,15 @@ CONFIG_E1000=m CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_PASEMI_MAC is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set CONFIG_TR=y CONFIG_IBMOL=y # CONFIG_3C359 is not set @@ -669,6 +685,7 @@ CONFIG_SLHC=m # CONFIG_NET_FC is not set # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=y +# CONFIG_NETCONSOLE_DYNAMIC is not set CONFIG_NETPOLL=y CONFIG_NETPOLL_TRAP=y CONFIG_NET_POLL_CONTROLLER=y @@ -690,7 +707,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -736,14 +752,11 @@ CONFIG_LEGACY_PTY_COUNT=256 CONFIG_HVC_DRIVER=y CONFIG_HVC_ISERIES=y # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set CONFIG_RAW_DRIVER=y CONFIG_MAX_RAW_DEVS=256 # CONFIG_HANGCHECK_TIMER is not set @@ -759,6 +772,13 @@ CONFIG_DEVPORT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -775,16 +795,17 @@ CONFIG_DEVPORT=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -806,19 +827,6 @@ CONFIG_DUMMY_CONSOLE=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -902,7 +910,6 @@ CONFIG_TMPFS=y CONFIG_TMPFS_POSIX_ACL=y # CONFIG_HUGETLBFS is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=m # @@ -921,10 +928,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -963,10 +967,6 @@ CONFIG_CIFS_POSIX=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -1007,10 +1007,6 @@ CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# CONFIG_DLM=m # CONFIG_DLM_DEBUG is not set # CONFIG_UCC_SLOW is not set @@ -1035,17 +1031,16 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y # CONFIG_PROFILING is not set # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1069,14 +1064,18 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set # CONFIG_FORCED_INLINING is not set +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set CONFIG_DEBUG_STACKOVERFLOW=y CONFIG_DEBUG_STACK_USAGE=y # CONFIG_DEBUG_PAGEALLOC is not set # CONFIG_DEBUGGER is not set CONFIG_IRQSTACKS=y +# CONFIG_VIRQ_DEBUG is not set # CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set @@ -1085,8 +1084,10 @@ CONFIG_IRQSTACKS=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_AEAD=m CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_MANAGER=y @@ -1105,6 +1106,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1119,9 +1121,12 @@ CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_SEED=m CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CAMELLIA is not set CONFIG_CRYPTO_TEST=m +CONFIG_CRYPTO_AUTHENC=m # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/kilauea_defconfig b/arch/powerpc/configs/kilauea_defconfig index fd1c530aa3ec..28dee12031f5 100644 --- a/arch/powerpc/configs/kilauea_defconfig +++ b/arch/powerpc/configs/kilauea_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc9 -# Thu Oct 11 19:05:15 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:20 2007 # # CONFIG_PPC64 is not set @@ -65,9 +65,12 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -154,6 +157,7 @@ CONFIG_KILAUEA=y # CONFIG_TICK_ONESHOT is not set # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -175,6 +179,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -198,10 +203,6 @@ CONFIG_ZONE_DMA=y # CONFIG_PCI_DOMAINS is not set # CONFIG_PCI_SYSCALL is not set # CONFIG_ARCH_SUPPORTS_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # @@ -215,7 +216,7 @@ CONFIG_ZONE_DMA=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_CONSISTENT_START=0xff100000 CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_BOOT_LOAD=0x00400000 @@ -252,6 +253,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -277,10 +279,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -309,6 +307,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -336,6 +335,7 @@ CONFIG_MTD_BLOCK=m # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -425,6 +425,7 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set # CONFIG_NET_ETHERNET is not set # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -485,7 +486,6 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set @@ -502,6 +502,13 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -518,16 +525,15 @@ CONFIG_LEGACY_PTY_COUNT=256 # # Graphics support # +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -540,19 +546,6 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -604,7 +597,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -624,10 +616,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -653,15 +642,7 @@ CONFIG_SUNRPC=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -680,16 +661,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -713,9 +691,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -728,6 +709,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -747,6 +729,7 @@ CONFIG_CRYPTO_ECB=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=y # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -760,10 +743,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y # CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/linkstation_defconfig b/arch/powerpc/configs/linkstation_defconfig index 401033aefd40..7b4280811fb9 100644 --- a/arch/powerpc/configs/linkstation_defconfig +++ b/arch/powerpc/configs/linkstation_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:38 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:22 2007 # # CONFIG_PPC64 is not set @@ -15,13 +15,19 @@ CONFIG_6xx=y # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_FPU=y +# CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -61,10 +67,13 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -85,7 +94,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -124,16 +132,21 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # # Platform support # -# CONFIG_PPC_MULTIPLATFORM is not set -CONFIG_EMBEDDED6xx=y +CONFIG_PPC_MULTIPLATFORM=y # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set +CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set # CONFIG_PPC_MPC52xx is not set # CONFIG_PPC_MPC5200 is not set +# CONFIG_PPC_EFIKA is not set +# CONFIG_PPC_LITE5200 is not set +# CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PQ2ADS is not set +CONFIG_EMBEDDED6xx=y CONFIG_LINKSTATION=y # CONFIG_MPC7448HPC2 is not set # CONFIG_PPC_HOLLY is not set @@ -151,6 +164,7 @@ CONFIG_MPIC=y # CONFIG_PPC_INDIRECT_IO is not set # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set +# CONFIG_TAU is not set # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set @@ -158,6 +172,10 @@ CONFIG_MPIC=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y CONFIG_HZ_100=y # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set @@ -169,6 +187,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +# CONFIG_KEXEC is not set CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y @@ -178,6 +197,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -186,6 +206,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y # CONFIG_WANT_DEVICE_TREE is not set CONFIG_ISA_DMA_API=y @@ -203,11 +225,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -222,7 +241,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -262,6 +281,7 @@ CONFIG_IP_PNP_BOOTP=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -330,6 +350,7 @@ CONFIG_NETFILTER_XT_MATCH_STATE=m # CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set # CONFIG_NETFILTER_XT_MATCH_STRING is not set # CONFIG_NETFILTER_XT_MATCH_TCPMSS is not set +# CONFIG_NETFILTER_XT_MATCH_TIME is not set # CONFIG_NETFILTER_XT_MATCH_U32 is not set # CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set @@ -390,10 +411,6 @@ CONFIG_IP_NF_ARP_MANGLE=m # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -428,6 +445,7 @@ CONFIG_IEEE80211_SOFTMAC_DEBUG=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=m @@ -453,6 +471,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -493,6 +512,7 @@ CONFIG_MTD_PHYSMAP_START=0xffc00000 CONFIG_MTD_PHYSMAP_LEN=0x400000 CONFIG_MTD_PHYSMAP_BANKWIDTH=1 # CONFIG_MTD_PHYSMAP_OF is not set +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -580,6 +600,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -591,6 +612,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -658,6 +680,7 @@ CONFIG_PATA_IT821X=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -671,14 +694,7 @@ CONFIG_PATA_SIL680=y # CONFIG_PATA_VIA is not set # CONFIG_PATA_WINBOND is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -694,6 +710,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -713,11 +731,17 @@ CONFIG_TULIP_MMIO=y # CONFIG_DM9102 is not set # CONFIG_ULI526X is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -726,19 +750,24 @@ CONFIG_R8169=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -754,7 +783,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -764,6 +792,7 @@ CONFIG_NETDEV_10000=y # CONFIG_NET_FC is not set # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=y +# CONFIG_NETCONSOLE_DYNAMIC is not set CONFIG_NETPOLL=y # CONFIG_NETPOLL_TRAP is not set CONFIG_NET_POLL_CONTROLLER=y @@ -785,7 +814,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_EVBUG is not set @@ -846,14 +874,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -923,8 +948,6 @@ CONFIG_SENSORS_EEPROM=m # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -932,12 +955,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -973,6 +997,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -989,16 +1020,17 @@ CONFIG_HWMON=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -1013,6 +1045,7 @@ CONFIG_DUMMY_CONSOLE=y CONFIG_HID_SUPPORT=y CONFIG_HID=m # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1076,6 +1109,7 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -1107,6 +1141,7 @@ CONFIG_USB_SERIAL_CONSOLE=y # CONFIG_USB_SERIAL_AIRPRIME is not set # CONFIG_USB_SERIAL_ARK3116 is not set # CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_CH341 is not set # CONFIG_USB_SERIAL_WHITEHEAT is not set # CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set # CONFIG_USB_SERIAL_CP2101 is not set @@ -1196,6 +1231,7 @@ CONFIG_RTC_INTF_DEV=y # I2C RTC drivers # # CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set CONFIG_RTC_DRV_RS5C372=y @@ -1225,19 +1261,6 @@ CONFIG_RTC_DRV_RS5C372=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1254,7 +1277,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1307,7 +1329,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1327,10 +1348,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1368,10 +1386,6 @@ CONFIG_CIFS=m # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# CONFIG_NLS=m CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=m @@ -1412,10 +1426,6 @@ CONFIG_NLS_ISO8859_1=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1437,18 +1447,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -CONFIG_PROFILING=y -CONFIG_OPROFILE=m -# CONFIG_KPROBES is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1472,14 +1477,18 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set # CONFIG_DEBUGGER is not set # CONFIG_BDI_SWITCH is not set +# CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1487,6 +1496,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1506,6 +1516,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1520,9 +1531,12 @@ CONFIG_CRYPTO_AES=m CONFIG_CRYPTO_ARC4=m # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/lite5200_defconfig b/arch/powerpc/configs/lite5200_defconfig index dd78ed955eb0..02bb7e5d8ed5 100644 --- a/arch/powerpc/configs/lite5200_defconfig +++ b/arch/powerpc/configs/lite5200_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:38 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:24 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -138,6 +144,7 @@ CONFIG_PPC_LITE5200=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PQ2ADS is not set +# CONFIG_EMBEDDED6xx is not set # CONFIG_MPIC is not set # CONFIG_MPIC_WEIRD is not set # CONFIG_PPC_I8259 is not set @@ -151,11 +158,19 @@ CONFIG_PPC_LITE5200=y # CONFIG_TAU is not set # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set +CONFIG_PPC_BESTCOMM=y +CONFIG_PPC_BESTCOMM_ATA=y +CONFIG_PPC_BESTCOMM_FEC=y +CONFIG_PPC_BESTCOMM_GEN_BD=y # # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -177,6 +192,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -188,10 +204,13 @@ CONFIG_PM=y # CONFIG_PM_LEGACY is not set # CONFIG_PM_DEBUG is not set CONFIG_PM_SLEEP=y +CONFIG_SUSPEND_UP_POSSIBLE=y CONFIG_SUSPEND=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_HIBERNATION is not set CONFIG_SECCOMP=y -# CONFIG_WANT_DEVICE_TREE is not set +CONFIG_WANT_DEVICE_TREE=y +CONFIG_DEVICE_TREE="" CONFIG_ISA_DMA_API=y # @@ -207,11 +226,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -226,7 +242,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -266,6 +282,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -291,10 +308,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -323,6 +336,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -393,6 +407,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -404,6 +419,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -472,6 +488,7 @@ CONFIG_PATA_MPC52xx=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -486,14 +503,7 @@ CONFIG_PATA_MPC52xx=y # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -509,12 +519,15 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_NET_ETHERNET is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -522,6 +535,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -531,11 +545,14 @@ CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -592,14 +609,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -613,6 +627,13 @@ CONFIG_DEVPORT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -629,16 +650,17 @@ CONFIG_DEVPORT=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -665,19 +687,6 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -694,7 +703,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -735,7 +743,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -754,10 +761,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y # CONFIG_NFS_FS is not set # CONFIG_NFSD is not set # CONFIG_SMB_FS is not set @@ -771,15 +775,7 @@ CONFIG_RAMFS=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -796,16 +792,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # CONFIG_PRINTK_TIME=y +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -829,9 +822,12 @@ CONFIG_SCHED_DEBUG=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -845,4 +841,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +CONFIG_PPC_CLOCK=y +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/maple_defconfig b/arch/powerpc/configs/maple_defconfig index 84b9ab4a5a92..8b810d056440 100644 --- a/arch/powerpc/configs/maple_defconfig +++ b/arch/powerpc/configs/maple_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:38:16 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:26 2007 # CONFIG_PPC64=y @@ -10,6 +10,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY=y CONFIG_POWER4=y +# CONFIG_TUNE_CELL is not set CONFIG_PPC_FPU=y # CONFIG_ALTIVEC is not set CONFIG_PPC_STD_MMU=y @@ -18,8 +19,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=4 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,11 +68,13 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=17 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set # CONFIG_BLK_DEV_INITRD is not set @@ -86,7 +94,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -107,6 +114,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set # CONFIG_BLK_DEV_BSG is not set +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -125,7 +133,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -165,6 +172,10 @@ CONFIG_PPC_970_NAP=y # # Kernel options # +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -177,6 +188,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_FORCE_MAX_ZONEORDER=13 +CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y CONFIG_IOMMU_VMERGE=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_KEXEC=y @@ -194,6 +206,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y CONFIG_ZONE_DMA_FLAG=1 @@ -220,11 +233,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_PCI_MSI=y +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set CONFIG_KERNEL_START=0xc000000000000000 @@ -266,6 +276,7 @@ CONFIG_IP_PNP_DHCP=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -291,10 +302,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -323,6 +330,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -373,6 +381,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -380,8 +393,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set CONFIG_BLK_DEV_AMD74XX=y @@ -409,7 +420,7 @@ CONFIG_BLK_DEV_AMD74XX=y # CONFIG_BLK_DEV_TC86C001 is not set # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -421,10 +432,6 @@ CONFIG_BLK_DEV_IDEDMA=y # CONFIG_SCSI_NETLINK is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set # @@ -441,6 +448,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -451,6 +460,10 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set CONFIG_AMD8111_ETH=y @@ -458,7 +471,6 @@ CONFIG_AMD8111_ETH=y # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set @@ -477,6 +489,7 @@ CONFIG_NETDEV_1000=y CONFIG_E1000=y # CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -484,6 +497,7 @@ CONFIG_E1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=y # CONFIG_BNX2 is not set @@ -492,12 +506,15 @@ CONFIG_TIGON3=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_PASEMI_MAC is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -513,7 +530,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set CONFIG_USB_PEGASUS=y # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -542,7 +558,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1600 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1200 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -594,14 +609,11 @@ CONFIG_LEGACY_PTY_COUNT=256 CONFIG_HVC_DRIVER=y CONFIG_HVC_RTAS=y # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_HANGCHECK_TIMER is not set # CONFIG_TCG_TPM is not set @@ -669,6 +681,13 @@ CONFIG_I2C_AMD8111=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -685,16 +704,17 @@ CONFIG_I2C_AMD8111=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -709,6 +729,7 @@ CONFIG_DUMMY_CONSOLE=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -784,6 +805,7 @@ CONFIG_USB_SERIAL_GENERIC=y # CONFIG_USB_SERIAL_AIRPRIME is not set # CONFIG_USB_SERIAL_ARK3116 is not set # CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_CH341 is not set # CONFIG_USB_SERIAL_WHITEHEAT is not set # CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set # CONFIG_USB_SERIAL_CP2101 is not set @@ -870,19 +892,6 @@ CONFIG_USB_EZUSB=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -942,7 +951,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -961,10 +969,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1008,10 +1013,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="utf-8" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1052,10 +1053,6 @@ CONFIG_NLS_DEFAULT="utf-8" # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=y - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1074,17 +1071,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set -# CONFIG_KPROBES is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1108,9 +1101,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set # CONFIG_FORCED_INLINING is not set +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set CONFIG_DEBUG_STACKOVERFLOW=y CONFIG_DEBUG_STACK_USAGE=y # CONFIG_DEBUG_PAGEALLOC is not set @@ -1119,6 +1115,7 @@ CONFIG_XMON=y CONFIG_XMON_DEFAULT=y CONFIG_XMON_DISASSEMBLY=y # CONFIG_IRQSTACKS is not set +# CONFIG_VIRQ_DEBUG is not set CONFIG_BOOTX_TEXT=y # CONFIG_PPC_EARLY_DEBUG is not set @@ -1127,6 +1124,7 @@ CONFIG_BOOTX_TEXT=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1146,6 +1144,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1159,9 +1158,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc7448_hpc2_defconfig b/arch/powerpc/configs/mpc7448_hpc2_defconfig index 87ae894551b7..b0266de48491 100644 --- a/arch/powerpc/configs/mpc7448_hpc2_defconfig +++ b/arch/powerpc/configs/mpc7448_hpc2_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:39 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:28 2007 # # CONFIG_PPC64 is not set @@ -15,13 +15,19 @@ CONFIG_6xx=y # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_FPU=y +CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -61,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +92,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -117,16 +125,21 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # # Platform support # -# CONFIG_PPC_MULTIPLATFORM is not set -CONFIG_EMBEDDED6xx=y +CONFIG_PPC_MULTIPLATFORM=y # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set +CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set # CONFIG_PPC_MPC52xx is not set # CONFIG_PPC_MPC5200 is not set +# CONFIG_PPC_EFIKA is not set +# CONFIG_PPC_LITE5200 is not set +# CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PQ2ADS is not set +CONFIG_EMBEDDED6xx=y # CONFIG_LINKSTATION is not set CONFIG_MPC7448HPC2=y # CONFIG_PPC_HOLLY is not set @@ -142,6 +155,7 @@ CONFIG_MPIC_WEIRD=y # CONFIG_PPC_INDIRECT_IO is not set # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set +# CONFIG_TAU is not set # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set @@ -149,6 +163,10 @@ CONFIG_MPIC_WEIRD=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -160,6 +178,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y +# CONFIG_KEXEC is not set CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_SELECT_MEMORY_MODEL=y @@ -169,6 +188,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -177,8 +197,11 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_SECCOMP is not set -# CONFIG_WANT_DEVICE_TREE is not set +CONFIG_WANT_DEVICE_TREE=y +CONFIG_DEVICE_TREE="" CONFIG_ISA_DMA_API=y # @@ -193,10 +216,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -211,7 +231,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -251,6 +271,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -276,10 +297,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -308,6 +325,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -375,6 +393,7 @@ CONFIG_BLK_DEV_SD=y # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -386,6 +405,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -453,6 +473,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -467,14 +488,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -490,6 +504,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -506,6 +522,7 @@ CONFIG_PHYLIB=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -514,13 +531,16 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=y # CONFIG_FEALNX is not set @@ -542,6 +562,7 @@ CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -549,20 +570,25 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set CONFIG_TSI108_ETH=y +# CONFIG_MV643XX_ETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -595,7 +621,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -643,15 +668,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -666,9 +688,9 @@ CONFIG_DEVPORT=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set @@ -681,6 +703,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -697,16 +726,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -715,6 +745,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -736,19 +767,6 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -765,7 +783,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -806,7 +823,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -825,10 +841,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set @@ -868,15 +881,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -894,23 +899,23 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set +# CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -918,4 +923,6 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc8272_ads_defconfig b/arch/powerpc/configs/mpc8272_ads_defconfig index 865a942ecc69..a31b7a030a6b 100644 --- a/arch/powerpc/configs/mpc8272_ads_defconfig +++ b/arch/powerpc/configs/mpc8272_ads_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Wed Sep 5 12:43:23 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:30 2007 # # CONFIG_PPC64 is not set @@ -20,8 +20,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,6 +68,8 @@ CONFIG_SYSVIPC_SYSCTL=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set # CONFIG_BLK_DEV_INITRD is not set @@ -81,7 +88,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -115,7 +121,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set CONFIG_PPC_82xx=y # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -124,6 +129,7 @@ CONFIG_PPC_82xx=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set CONFIG_MPC8272_ADS=y +# CONFIG_PQ2FADS is not set CONFIG_PQ2ADS=y CONFIG_8260=y CONFIG_8272=y @@ -147,6 +153,10 @@ CONFIG_CPM=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -163,6 +173,7 @@ CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -171,9 +182,10 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y -# CONFIG_BUILD_RAW_IMAGE is not set CONFIG_DEVICE_TREE="mpc8272ads.dts" CONFIG_ISA_DMA_API=y @@ -190,11 +202,8 @@ CONFIG_PCI_8260=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # @@ -208,7 +217,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00400000 # @@ -245,6 +254,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -288,10 +298,6 @@ CONFIG_NETFILTER=y # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -317,6 +323,7 @@ CONFIG_NETFILTER=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -340,6 +347,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -378,6 +386,7 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_PHYSMAP is not set CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_SBC8240 is not set +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -429,10 +438,6 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_SCSI_NETLINK is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set # @@ -451,6 +456,7 @@ CONFIG_NETDEVICES=y # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=y +# CONFIG_VETH is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -476,20 +482,28 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FCC=y +# CONFIG_FS_ENET_MDIO_FCC is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -497,11 +511,14 @@ CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -539,7 +556,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set @@ -609,14 +625,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set CONFIG_DEVPORT=y # CONFIG_I2C is not set @@ -629,6 +642,13 @@ CONFIG_DEVPORT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -645,16 +665,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -668,19 +689,6 @@ CONFIG_DAB=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -696,7 +704,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -736,7 +743,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # # Miscellaneous filesystems @@ -749,10 +755,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -790,10 +793,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -852,11 +851,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -880,8 +881,11 @@ CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -924,8 +928,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc8313_rdb_defconfig b/arch/powerpc/configs/mpc8313_rdb_defconfig index 259d40d1eb5a..c9af905bbb1d 100644 --- a/arch/powerpc/configs/mpc8313_rdb_defconfig +++ b/arch/powerpc/configs/mpc8313_rdb_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:39 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:31 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set CONFIG_PPC_83xx=y # CONFIG_PPC_86xx is not set @@ -156,6 +162,10 @@ CONFIG_PPC_MPC831x=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -176,6 +186,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -184,6 +195,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -202,11 +215,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -221,7 +231,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -261,6 +271,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -286,10 +297,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -318,6 +325,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -342,6 +350,7 @@ CONFIG_MTD_CHAR=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -377,6 +386,7 @@ CONFIG_MTD_PHYSMAP_START=0xfe000000 CONFIG_MTD_PHYSMAP_LEN=0x1000000 CONFIG_MTD_PHYSMAP_BANKWIDTH=2 # CONFIG_MTD_PHYSMAP_OF is not set +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -466,6 +476,7 @@ CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -477,6 +488,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -512,14 +524,7 @@ CONFIG_MD_RAID1=y # CONFIG_MD_MULTIPATH is not set # CONFIG_MD_FAULTY is not set # CONFIG_BLK_DEV_DM is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -535,6 +540,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -551,6 +558,7 @@ CONFIG_CICADA_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -559,13 +567,16 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=y # CONFIG_FEALNX is not set @@ -583,6 +594,7 @@ CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -590,6 +602,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -600,11 +613,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -620,7 +636,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -647,7 +662,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -695,32 +709,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_83xx_WDT=y - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set - -# -# USB-based Watchdog Cards -# -# CONFIG_USBPCWATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -804,8 +797,6 @@ CONFIG_SPI_MPC83xx=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -813,12 +804,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -855,6 +847,31 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -872,16 +889,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -890,6 +908,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -954,6 +973,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -1015,6 +1035,7 @@ CONFIG_USB_GADGET=y # CONFIG_USB_GADGET_DEBUG_FILES is not set CONFIG_USB_GADGET_SELECTED=y # CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set # CONFIG_USB_GADGET_FSL_USB2 is not set CONFIG_USB_GADGET_NET2280=y CONFIG_USB_NET2280=y @@ -1057,6 +1078,7 @@ CONFIG_RTC_INTF_DEV_UIE_EMUL=y # I2C RTC drivers # CONFIG_RTC_DRV_DS1307=y +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set @@ -1088,21 +1110,6 @@ CONFIG_RTC_DRV_DS1307=y # # -# DMA Engine support -# -CONFIG_DMA_ENGINE=y - -# -# DMA Clients -# -CONFIG_NET_DMA=y - -# -# DMA Devices -# -CONFIG_INTEL_IOATDMA=y - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1119,7 +1126,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1160,7 +1166,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1180,10 +1185,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -1226,15 +1228,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1252,16 +1246,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -1285,9 +1276,12 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1300,6 +1294,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1319,6 +1314,7 @@ CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1332,9 +1328,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc832x_mds_defconfig b/arch/powerpc/configs/mpc832x_mds_defconfig index e069018276ca..2d8951b1096e 100644 --- a/arch/powerpc/configs/mpc832x_mds_defconfig +++ b/arch/powerpc/configs/mpc832x_mds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:40 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:33 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set CONFIG_PPC_83xx=y # CONFIG_PPC_86xx is not set @@ -157,6 +163,10 @@ CONFIG_QUICC_ENGINE=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -178,6 +188,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -186,6 +197,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -204,10 +217,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -222,7 +232,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -262,6 +272,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -287,10 +298,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -319,6 +326,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -387,6 +395,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -398,6 +407,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -424,14 +434,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_SRP is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -447,6 +450,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -463,6 +468,7 @@ CONFIG_DAVICOM_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -471,11 +477,17 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -483,6 +495,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -497,11 +510,14 @@ CONFIG_UCC_GETH=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -534,7 +550,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -582,28 +597,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_83xx_WDT=y - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -672,8 +671,6 @@ CONFIG_I2C_MPC=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -681,12 +678,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -722,6 +720,26 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -738,16 +756,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -756,6 +775,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -823,19 +843,6 @@ CONFIG_RTC_DRV_DS1374=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -852,7 +859,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -893,7 +899,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -912,10 +917,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -954,15 +956,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set CONFIG_UCC_FAST=y @@ -982,23 +976,22 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1006,6 +999,7 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1025,6 +1019,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1038,9 +1033,13 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc832x_rdb_defconfig b/arch/powerpc/configs/mpc832x_rdb_defconfig index 7a5b13f4140f..761718a63b7c 100644 --- a/arch/powerpc/configs/mpc832x_rdb_defconfig +++ b/arch/powerpc/configs/mpc832x_rdb_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:27:19 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:35 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set CONFIG_PPC_83xx=y # CONFIG_PPC_86xx is not set @@ -157,6 +163,10 @@ CONFIG_QUICC_ENGINE=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -178,6 +188,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -186,6 +197,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -204,10 +217,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -222,7 +232,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -262,6 +272,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -287,10 +298,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -319,6 +326,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -388,6 +396,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -399,6 +408,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -425,14 +435,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_SRP is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -448,6 +451,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -464,6 +469,7 @@ CONFIG_PHYLIB=y # CONFIG_BROADCOM_PHY is not set CONFIG_ICPLUS_PHY=y # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -472,13 +478,19 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=y # CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -486,6 +498,7 @@ CONFIG_E1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -500,11 +513,14 @@ CONFIG_UGETH_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -520,7 +536,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -547,7 +562,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -595,33 +609,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_83xx_WDT=y - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set - -# -# USB-based Watchdog Cards -# -# CONFIG_USBPCWATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -704,8 +697,6 @@ CONFIG_SPI_MPC83xx=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -713,12 +704,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -755,6 +747,31 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -772,16 +789,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -790,6 +808,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -853,6 +872,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -934,19 +954,6 @@ CONFIG_MMC_SPI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -963,7 +970,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1007,7 +1013,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1026,10 +1031,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -1073,10 +1075,6 @@ CONFIG_LDM_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -1117,10 +1115,6 @@ CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set CONFIG_UCC_FAST=y @@ -1140,23 +1134,22 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1164,6 +1157,7 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1183,6 +1177,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1196,9 +1191,13 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc834x_itx_defconfig b/arch/powerpc/configs/mpc834x_itx_defconfig index ba512d13f3a3..6feb86e2b786 100644 --- a/arch/powerpc/configs/mpc834x_itx_defconfig +++ b/arch/powerpc/configs/mpc834x_itx_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:41 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:37 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set CONFIG_PPC_83xx=y # CONFIG_PPC_86xx is not set @@ -156,6 +162,10 @@ CONFIG_MPC834x=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -176,6 +186,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -184,6 +195,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -202,10 +215,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -220,7 +230,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -260,6 +270,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -285,10 +296,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -317,6 +324,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -339,6 +347,7 @@ CONFIG_MTD_CHAR=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -374,6 +383,7 @@ CONFIG_MTD_PHYSMAP_START=0xfe000000 CONFIG_MTD_PHYSMAP_LEN=0x1000000 CONFIG_MTD_PHYSMAP_BANKWIDTH=2 # CONFIG_MTD_PHYSMAP_OF is not set +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -467,6 +477,7 @@ CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -478,6 +489,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -545,6 +557,7 @@ CONFIG_SATA_SIL=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -568,14 +581,7 @@ CONFIG_MD_RAID1=y # CONFIG_MD_MULTIPATH is not set # CONFIG_MD_FAULTY is not set # CONFIG_BLK_DEV_DM is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -591,6 +597,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -607,11 +615,13 @@ CONFIG_CICADA_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set # CONFIG_NET_ETHERNET is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -619,6 +629,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -629,11 +640,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -649,7 +663,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -703,32 +716,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_83xx_WDT=y - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set - -# -# USB-based Watchdog Cards -# -# CONFIG_USBPCWATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -810,6 +802,31 @@ CONFIG_SPI_MPC83xx=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -827,16 +844,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -888,6 +906,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -968,6 +987,7 @@ CONFIG_RTC_INTF_DEV_UIE_EMUL=y # I2C RTC drivers # CONFIG_RTC_DRV_DS1307=y +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set @@ -999,21 +1019,6 @@ CONFIG_RTC_DRV_DS1307=y # # -# DMA Engine support -# -CONFIG_DMA_ENGINE=y - -# -# DMA Clients -# -CONFIG_NET_DMA=y - -# -# DMA Devices -# -CONFIG_INTEL_IOATDMA=y - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1030,7 +1035,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1074,7 +1078,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1094,10 +1097,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -1140,10 +1140,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1184,10 +1180,6 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1205,23 +1197,22 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1229,6 +1220,7 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1248,6 +1240,7 @@ CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1261,9 +1254,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc834x_itxgp_defconfig b/arch/powerpc/configs/mpc834x_itxgp_defconfig index 9faa948c22ad..67cb09cc3ace 100644 --- a/arch/powerpc/configs/mpc834x_itxgp_defconfig +++ b/arch/powerpc/configs/mpc834x_itxgp_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:41 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:39 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set CONFIG_PPC_83xx=y # CONFIG_PPC_86xx is not set @@ -156,6 +162,10 @@ CONFIG_MPC834x=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -176,6 +186,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -184,6 +195,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -202,10 +215,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -220,7 +230,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -260,6 +270,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -285,10 +296,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -317,6 +324,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -339,6 +347,7 @@ CONFIG_MTD_CHAR=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -374,6 +383,7 @@ CONFIG_MTD_PHYSMAP_START=0xfe000000 CONFIG_MTD_PHYSMAP_LEN=0x800000 CONFIG_MTD_PHYSMAP_BANKWIDTH=2 # CONFIG_MTD_PHYSMAP_OF is not set +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -413,6 +423,7 @@ CONFIG_BLK_DEV_LOOP=y # CONFIG_BLK_DEV_CRYPTOLOOP is not set # CONFIG_BLK_DEV_NBD is not set # CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=16 CONFIG_BLK_DEV_RAM_SIZE=32768 @@ -462,6 +473,7 @@ CONFIG_SCSI_SPI_ATTRS=y # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -473,6 +485,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -499,14 +512,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_SRP is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -522,6 +528,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -538,11 +546,13 @@ CONFIG_CICADA_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set # CONFIG_NET_ETHERNET is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -550,6 +560,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -560,11 +571,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -572,6 +586,15 @@ CONFIG_NETDEV_10000=y # # CONFIG_WLAN_PRE80211 is not set # CONFIG_WLAN_80211 is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set # CONFIG_HIPPI is not set @@ -624,27 +647,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_83xx_WDT=y - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -682,6 +689,7 @@ CONFIG_I2C_MPC=y # CONFIG_I2C_SIS96X is not set # CONFIG_I2C_TAOS_EVM is not set # CONFIG_I2C_STUB is not set +# CONFIG_I2C_TINY_USB is not set # CONFIG_I2C_VIA is not set # CONFIG_I2C_VIAPRO is not set # CONFIG_I2C_VOODOO3 is not set @@ -725,6 +733,31 @@ CONFIG_SPI_MPC83xx=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -737,20 +770,22 @@ CONFIG_SPI_MPC83xx=y # CONFIG_VIDEO_DEV is not set # CONFIG_DVB_CORE is not set CONFIG_DAB=y +# CONFIG_USB_DABUSB is not set # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -802,6 +837,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -881,6 +917,7 @@ CONFIG_RTC_INTF_DEV_UIE_EMUL=y # I2C RTC drivers # CONFIG_RTC_DRV_DS1307=y +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set @@ -912,21 +949,6 @@ CONFIG_RTC_DRV_DS1307=y # # -# DMA Engine support -# -CONFIG_DMA_ENGINE=y - -# -# DMA Clients -# -CONFIG_NET_DMA=y - -# -# DMA Devices -# -CONFIG_INTEL_IOATDMA=y - -# # Userspace I/O # # CONFIG_UIO is not set @@ -943,7 +965,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -987,7 +1008,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1007,10 +1027,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -1053,10 +1070,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1097,10 +1110,6 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1118,23 +1127,22 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1142,6 +1150,7 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1161,6 +1170,7 @@ CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1174,9 +1184,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc834x_mds_defconfig b/arch/powerpc/configs/mpc834x_mds_defconfig index 356f736a5d3d..217539f3ecef 100644 --- a/arch/powerpc/configs/mpc834x_mds_defconfig +++ b/arch/powerpc/configs/mpc834x_mds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:41 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:41 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set CONFIG_PPC_83xx=y # CONFIG_PPC_86xx is not set @@ -156,6 +162,10 @@ CONFIG_MPC834x=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -176,6 +186,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -184,6 +195,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -202,10 +215,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -220,7 +230,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -260,6 +270,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -285,10 +296,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -317,6 +324,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -358,10 +366,6 @@ CONFIG_MISC_DEVICES=y # CONFIG_SCSI_NETLINK is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set # @@ -378,6 +382,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -394,6 +400,7 @@ CONFIG_MARVELL_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -402,13 +409,16 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=y # CONFIG_FEALNX is not set @@ -426,6 +436,7 @@ CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -433,6 +444,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -443,11 +455,14 @@ CONFIG_GIANFAR=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -479,7 +494,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -527,28 +541,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_83xx_WDT=y - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -617,8 +615,6 @@ CONFIG_I2C_MPC=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -626,12 +622,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -667,6 +664,26 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -683,16 +700,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -701,6 +719,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -770,19 +789,6 @@ CONFIG_RTC_DRV_DS1374=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -799,7 +805,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -840,7 +845,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -859,10 +863,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -901,15 +902,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -927,23 +920,22 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -951,6 +943,7 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -970,6 +963,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -983,9 +977,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc836x_mds_defconfig b/arch/powerpc/configs/mpc836x_mds_defconfig index 1b4d37570eb1..c44fc56263e2 100644 --- a/arch/powerpc/configs/mpc836x_mds_defconfig +++ b/arch/powerpc/configs/mpc836x_mds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:42 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:43 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -62,9 +67,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -83,7 +91,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -123,7 +130,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set CONFIG_PPC_83xx=y # CONFIG_PPC_86xx is not set @@ -157,6 +163,10 @@ CONFIG_QUICC_ENGINE=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -177,6 +187,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -185,6 +196,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -203,10 +216,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -221,7 +231,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -261,6 +271,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -286,10 +297,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -318,6 +325,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -386,6 +394,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -397,6 +406,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -423,14 +433,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_SRP is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -446,6 +449,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -462,6 +467,7 @@ CONFIG_MARVELL_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -470,11 +476,17 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -482,6 +494,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -496,11 +509,14 @@ CONFIG_UCC_GETH=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -533,7 +549,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -581,28 +596,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -CONFIG_83xx_WDT=y - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -671,8 +670,6 @@ CONFIG_I2C_MPC=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -680,12 +677,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -721,6 +719,26 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_83xx_WDT=y + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -737,16 +755,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -755,6 +774,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -822,19 +842,6 @@ CONFIG_RTC_DRV_DS1374=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -851,7 +858,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -892,7 +898,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -911,10 +916,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -953,15 +955,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set CONFIG_UCC_FAST=y @@ -981,23 +975,22 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set # CONFIG_DEBUG_BUGVERBOSE is not set +# CONFIG_SAMPLES is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1005,6 +998,7 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1024,6 +1018,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1037,9 +1032,13 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc8540_ads_defconfig b/arch/powerpc/configs/mpc8540_ads_defconfig index b953b2c51453..3791e29e7d06 100644 --- a/arch/powerpc/configs/mpc8540_ads_defconfig +++ b/arch/powerpc/configs/mpc8540_ads_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:42 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:44 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_FSL_BOOKE=y CONFIG_SPE=y # CONFIG_PPC_MM_SLICES is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,9 +68,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -86,7 +94,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -129,7 +136,7 @@ CONFIG_MPC8540_ADS=y # CONFIG_MPC8560_ADS is not set # CONFIG_MPC85xx_CDS is not set # CONFIG_MPC85xx_MDS is not set -# CONFIG_MPC8544_DS is not set +# CONFIG_MPC85xx_DS is not set CONFIG_MPC8540=y CONFIG_MPC85xx=y CONFIG_MPIC=y @@ -149,6 +156,10 @@ CONFIG_MPIC=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -170,6 +181,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -178,6 +190,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_SECCOMP is not set CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -193,10 +207,6 @@ CONFIG_FSL_SOC=y # CONFIG_PCI_DOMAINS is not set # CONFIG_PCI_SYSCALL is not set # CONFIG_ARCH_SUPPORTS_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # @@ -210,7 +220,7 @@ CONFIG_FSL_SOC=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -250,6 +260,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -275,10 +286,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -307,6 +314,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -350,6 +358,7 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set CONFIG_PHYLIB=y # @@ -365,8 +374,14 @@ CONFIG_PHYLIB=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y CONFIG_GIANFAR=y CONFIG_GFAR_NAPI=y @@ -399,7 +414,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -446,7 +460,6 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y @@ -465,9 +478,8 @@ CONFIG_GEN_RTC=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set @@ -477,6 +489,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -493,16 +512,15 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -511,6 +529,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set @@ -530,19 +549,6 @@ CONFIG_USB_SUPPORT=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -559,7 +565,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -600,7 +605,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -619,10 +623,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set @@ -658,15 +659,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -684,16 +677,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -717,8 +707,11 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -731,4 +724,6 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc8544_ds_defconfig b/arch/powerpc/configs/mpc8544_ds_defconfig index 9a3e08bcd188..18623a8ee75c 100644 --- a/arch/powerpc/configs/mpc8544_ds_defconfig +++ b/arch/powerpc/configs/mpc8544_ds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Wed Aug 29 16:41:04 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:46 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_FSL_BOOKE=y CONFIG_SPE=y # CONFIG_PPC_MM_SLICES is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -64,11 +69,14 @@ CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set CONFIG_AUDIT=y # CONFIG_AUDITSYSCALL is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -89,7 +97,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -156,6 +163,10 @@ CONFIG_FSL_ULI1575=y # Kernel options # CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -177,6 +188,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -185,6 +197,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -194,6 +208,7 @@ CONFIG_ISA_DMA_API=y # Bus options # CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y CONFIG_PPC_INDIRECT_PCI=y CONFIG_FSL_SOC=y CONFIG_FSL_PCI=y @@ -203,11 +218,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -222,7 +234,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -271,6 +283,7 @@ CONFIG_INET_TUNNEL=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -315,10 +328,6 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -348,6 +357,7 @@ CONFIG_FIB_RULES=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -420,6 +430,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -431,6 +442,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -498,6 +510,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -512,14 +525,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -535,6 +541,8 @@ CONFIG_DUMMY=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -551,6 +559,7 @@ CONFIG_VITESSE_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -559,11 +568,17 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -571,6 +586,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -581,11 +597,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -601,7 +620,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -628,7 +646,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -688,15 +705,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_NVRAM=y CONFIG_GEN_RTC=y CONFIG_GEN_RTC_X=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -765,6 +779,13 @@ CONFIG_SENSORS_EEPROM=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -859,6 +880,7 @@ CONFIG_DVB_CAPTURE_DRIVERS=y # CONFIG_DVB_OR51132 is not set # CONFIG_DVB_BCM3510 is not set # CONFIG_DVB_LGDT330X is not set +# CONFIG_DVB_S5H1409 is not set # # Tuners/PLL support @@ -868,6 +890,9 @@ CONFIG_DVB_CAPTURE_DRIVERS=y # CONFIG_DVB_TDA827X is not set # CONFIG_DVB_TUNER_QT1010 is not set # CONFIG_DVB_TUNER_MT2060 is not set +# CONFIG_DVB_TUNER_MT2266 is not set +# CONFIG_DVB_TUNER_MT2131 is not set +# CONFIG_DVB_TUNER_DIB0070 is not set # # Miscellaneous devices @@ -881,16 +906,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -1022,6 +1048,7 @@ CONFIG_AC97_BUS=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1082,6 +1109,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -1162,6 +1190,7 @@ CONFIG_RTC_INTF_DEV=y # I2C RTC drivers # # CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set @@ -1191,19 +1220,6 @@ CONFIG_RTC_DRV_CMOS=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1220,7 +1236,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1269,7 +1284,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1292,10 +1306,7 @@ CONFIG_SYSV_FS=m CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -1341,10 +1352,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1385,10 +1392,6 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1407,16 +1410,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -1441,9 +1441,12 @@ CONFIG_SCHED_DEBUG=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1456,6 +1459,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1466,7 +1470,7 @@ CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_NULL is not set # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y -# CONFIG_CRYPTO_SHA1 is not set +CONFIG_CRYPTO_SHA1=m # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set # CONFIG_CRYPTO_WP512 is not set @@ -1476,6 +1480,7 @@ CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1489,9 +1494,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc8560_ads_defconfig b/arch/powerpc/configs/mpc8560_ads_defconfig index 0211e6b68e1a..51f9693bacd4 100644 --- a/arch/powerpc/configs/mpc8560_ads_defconfig +++ b/arch/powerpc/configs/mpc8560_ads_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc9 -# Thu Oct 11 09:16:32 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:48 2007 # # CONFIG_PPC64 is not set @@ -68,9 +68,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -158,6 +161,7 @@ CONFIG_CPM=y # CONFIG_TICK_ONESHOT is not set # CONFIG_NO_HZ is not set # CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -179,6 +183,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -207,11 +212,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y CONFIG_PCI_DEBUG=y - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -226,7 +228,7 @@ CONFIG_PCI_DEBUG=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -266,6 +268,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -291,10 +294,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -323,6 +322,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -366,10 +366,6 @@ CONFIG_MISC_DEVICES=y # CONFIG_SCSI_NETLINK is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set # @@ -386,6 +382,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -402,6 +400,7 @@ CONFIG_DAVICOM_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -410,16 +409,23 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FCC=y +# CONFIG_FS_ENET_MDIO_FCC is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=y CONFIG_E1000_NAPI=y # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -438,11 +444,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -474,7 +483,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -524,15 +532,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -547,9 +552,9 @@ CONFIG_DEVPORT=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set @@ -562,6 +567,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -578,16 +590,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -596,6 +609,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -617,19 +631,6 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -646,7 +647,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -687,7 +687,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -706,10 +705,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set @@ -745,15 +741,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -771,16 +759,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -804,8 +789,11 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -819,5 +807,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set # CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc8568mds_defconfig b/arch/powerpc/configs/mpc8568mds_defconfig index d665e7a797c0..f51b58ae329a 100644 --- a/arch/powerpc/configs/mpc8568mds_defconfig +++ b/arch/powerpc/configs/mpc8568mds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:43 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:50 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_FSL_BOOKE=y CONFIG_SPE=y # CONFIG_PPC_MM_SLICES is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,9 +68,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -84,7 +92,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -132,7 +139,7 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_MPC8560_ADS is not set # CONFIG_MPC85xx_CDS is not set CONFIG_MPC85xx_MDS=y -# CONFIG_MPC8544_DS is not set +# CONFIG_MPC85xx_DS is not set CONFIG_MPC85xx=y CONFIG_MPIC=y # CONFIG_MPIC_WEIRD is not set @@ -144,6 +151,7 @@ CONFIG_MPIC=y # CONFIG_PPC_INDIRECT_IO is not set # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set +CONFIG_QUICC_ENGINE=y # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set @@ -151,6 +159,10 @@ CONFIG_MPIC=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -172,6 +184,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -180,6 +193,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -198,11 +213,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -217,7 +229,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -257,6 +269,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -282,10 +295,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -314,6 +323,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -384,6 +394,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -395,6 +406,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -421,14 +433,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_SRP is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -444,6 +449,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -460,6 +467,7 @@ CONFIG_MARVELL_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -468,11 +476,17 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -480,21 +494,26 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set CONFIG_GIANFAR=y CONFIG_GFAR_NAPI=y +# CONFIG_UCC_GETH is not set # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -527,7 +546,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -576,28 +594,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -CONFIG_WATCHDOG=y -# CONFIG_WATCHDOG_NOWAYOUT is not set - -# -# Watchdog Device Drivers -# -# CONFIG_SOFT_WATCHDOG is not set -# CONFIG_BOOKE_WDT is not set - -# -# PCI-based Watchdog Cards -# -# CONFIG_PCIPCWATCHDOG is not set -# CONFIG_WDTPCI is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -666,8 +668,6 @@ CONFIG_I2C_MPC=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -675,12 +675,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -716,6 +717,26 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_BOOKE_WDT is not set + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -732,16 +753,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -750,6 +772,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -817,19 +840,6 @@ CONFIG_RTC_DRV_DS1374=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -846,7 +856,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -887,7 +896,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -906,10 +914,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -948,15 +953,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -974,17 +971,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -CONFIG_PROFILING=y -CONFIG_OPROFILE=y +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -1008,9 +1001,12 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1027,12 +1023,14 @@ CONFIG_PPC_EARLY_DEBUG=y # CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set # CONFIG_PPC_EARLY_DEBUG_BEAT is not set # CONFIG_PPC_EARLY_DEBUG_44x is not set +# CONFIG_PPC_EARLY_DEBUG_CPM is not set # # Security options # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1052,6 +1050,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1065,9 +1064,13 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc8572_ds_defconfig b/arch/powerpc/configs/mpc8572_ds_defconfig index 4e85b2e88525..b40802d17e03 100644 --- a/arch/powerpc/configs/mpc8572_ds_defconfig +++ b/arch/powerpc/configs/mpc8572_ds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Sep 11 01:19:35 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:52 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_FSL_BOOKE=y CONFIG_SPE=y # CONFIG_PPC_MM_SLICES is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -64,11 +69,14 @@ CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set CONFIG_AUDIT=y # CONFIG_AUDITSYSCALL is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -89,7 +97,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -156,6 +163,10 @@ CONFIG_FSL_ULI1575=y # Kernel options # CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -177,6 +188,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -185,6 +197,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -194,6 +208,7 @@ CONFIG_ISA_DMA_API=y # Bus options # CONFIG_ZONE_DMA=y +CONFIG_GENERIC_ISA_DMA=y CONFIG_PPC_INDIRECT_PCI=y CONFIG_FSL_SOC=y CONFIG_FSL_PCI=y @@ -203,11 +218,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -222,7 +234,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -271,6 +283,7 @@ CONFIG_INET_TUNNEL=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -315,10 +328,6 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -348,6 +357,7 @@ CONFIG_FIB_RULES=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -420,6 +430,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -431,6 +442,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -498,6 +510,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -512,14 +525,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -535,6 +541,8 @@ CONFIG_DUMMY=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -551,6 +559,7 @@ CONFIG_VITESSE_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -559,11 +568,17 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -571,6 +586,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -581,11 +597,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -601,7 +620,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -628,7 +646,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -688,15 +705,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_NVRAM=y CONFIG_GEN_RTC=y CONFIG_GEN_RTC_X=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -765,6 +779,13 @@ CONFIG_SENSORS_EEPROM=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -859,6 +880,7 @@ CONFIG_DVB_CAPTURE_DRIVERS=y # CONFIG_DVB_OR51132 is not set # CONFIG_DVB_BCM3510 is not set # CONFIG_DVB_LGDT330X is not set +# CONFIG_DVB_S5H1409 is not set # # Tuners/PLL support @@ -868,6 +890,9 @@ CONFIG_DVB_CAPTURE_DRIVERS=y # CONFIG_DVB_TDA827X is not set # CONFIG_DVB_TUNER_QT1010 is not set # CONFIG_DVB_TUNER_MT2060 is not set +# CONFIG_DVB_TUNER_MT2266 is not set +# CONFIG_DVB_TUNER_MT2131 is not set +# CONFIG_DVB_TUNER_DIB0070 is not set # # Miscellaneous devices @@ -881,16 +906,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -1022,6 +1048,7 @@ CONFIG_AC97_BUS=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1082,6 +1109,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -1162,6 +1190,7 @@ CONFIG_RTC_INTF_DEV=y # I2C RTC drivers # # CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set @@ -1191,19 +1220,6 @@ CONFIG_RTC_DRV_CMOS=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1220,7 +1236,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1269,7 +1284,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1292,10 +1306,7 @@ CONFIG_SYSV_FS=m CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -1341,10 +1352,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1385,10 +1392,6 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1407,16 +1410,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -1441,9 +1441,12 @@ CONFIG_SCHED_DEBUG=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1456,6 +1459,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1466,7 +1470,7 @@ CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_NULL is not set # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y -# CONFIG_CRYPTO_SHA1 is not set +CONFIG_CRYPTO_SHA1=m # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set # CONFIG_CRYPTO_WP512 is not set @@ -1476,6 +1480,7 @@ CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1489,9 +1494,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc85xx_cds_defconfig b/arch/powerpc/configs/mpc85xx_cds_defconfig index a4f33d110542..2f9ad589b004 100644 --- a/arch/powerpc/configs/mpc85xx_cds_defconfig +++ b/arch/powerpc/configs/mpc85xx_cds_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:43 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:54 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_FSL_BOOKE=y CONFIG_SPE=y # CONFIG_PPC_MM_SLICES is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,9 +68,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -86,7 +94,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -129,7 +136,7 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # CONFIG_MPC8560_ADS is not set CONFIG_MPC85xx_CDS=y # CONFIG_MPC85xx_MDS is not set -# CONFIG_MPC8544_DS is not set +# CONFIG_MPC85xx_DS is not set CONFIG_MPC8540=y CONFIG_MPC85xx=y CONFIG_MPIC=y @@ -149,6 +156,10 @@ CONFIG_PPC_I8259=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -170,6 +181,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -178,6 +190,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_SECCOMP is not set CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="" @@ -196,11 +210,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -215,7 +226,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -255,6 +266,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -280,10 +292,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -312,6 +320,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -364,6 +373,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -371,8 +385,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set @@ -400,7 +412,7 @@ CONFIG_BLK_DEV_VIA82CXXX=y # CONFIG_BLK_DEV_TC86C001 is not set # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -412,10 +424,6 @@ CONFIG_BLK_DEV_IDEDMA=y # CONFIG_SCSI_NETLINK is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set # @@ -432,6 +440,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -448,6 +458,7 @@ CONFIG_PHYLIB=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -456,13 +467,19 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set CONFIG_E1000=y CONFIG_E1000_NAPI=y # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -470,6 +487,7 @@ CONFIG_E1000_NAPI=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -480,11 +498,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -516,7 +537,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -565,15 +585,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -588,9 +605,9 @@ CONFIG_DEVPORT=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set @@ -603,6 +620,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -619,16 +643,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -637,6 +662,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -658,19 +684,6 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -687,7 +700,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -728,7 +740,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -747,10 +758,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set @@ -786,15 +794,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -812,16 +812,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -845,8 +842,11 @@ CONFIG_DEBUG_MUTEXES=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -859,4 +859,6 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc8610_hpcd_defconfig b/arch/powerpc/configs/mpc8610_hpcd_defconfig index 0483211f52be..9614d24f832a 100644 --- a/arch/powerpc/configs/mpc8610_hpcd_defconfig +++ b/arch/powerpc/configs/mpc8610_hpcd_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc6 -# Tue Oct 2 11:42:56 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:56 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -61,10 +66,13 @@ CONFIG_LOCALVERSION="" # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -119,7 +127,6 @@ CONFIG_DEFAULT_IOSCHED="deadline" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set CONFIG_PPC_86xx=y @@ -148,6 +155,10 @@ CONFIG_MPIC=y # Kernel options # CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set @@ -168,6 +179,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -197,11 +209,8 @@ CONFIG_PCIEPORTBUS=y CONFIG_PCIEAER=y CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y CONFIG_PCI_DEBUG=y - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -216,7 +225,7 @@ CONFIG_PCI_DEBUG=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -255,6 +264,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -294,10 +304,6 @@ CONFIG_IPV6_SIT=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -326,6 +332,7 @@ CONFIG_IPV6_SIT=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -399,6 +406,7 @@ CONFIG_CHR_DEV_SG=y # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -410,6 +418,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -477,6 +486,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -491,14 +501,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -514,6 +517,8 @@ CONFIG_DUMMY=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -530,6 +535,7 @@ CONFIG_PHYLIB=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -547,13 +553,16 @@ CONFIG_TULIP_MMIO=y # CONFIG_DM9102 is not set # CONFIG_ULI526X is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set @@ -575,6 +584,7 @@ CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -592,11 +602,14 @@ CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -629,7 +642,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -688,14 +700,11 @@ CONFIG_SERIAL_OF_PLATFORM=y CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -709,6 +718,13 @@ CONFIG_DEVPORT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -725,16 +741,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -750,6 +767,7 @@ CONFIG_DUMMY_CONSOLE=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y CONFIG_USB_ARCH_HAS_HCD=y CONFIG_USB_ARCH_HAS_OHCI=y @@ -771,19 +789,6 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -800,7 +805,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -840,7 +844,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -859,10 +862,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -908,10 +908,6 @@ CONFIG_LDM_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -952,10 +948,6 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -973,16 +965,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -1007,8 +996,11 @@ CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1021,4 +1013,6 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc8641_hpcn_defconfig b/arch/powerpc/configs/mpc8641_hpcn_defconfig index ed214fcd8abe..ff092fc4c6be 100644 --- a/arch/powerpc/configs/mpc8641_hpcn_defconfig +++ b/arch/powerpc/configs/mpc8641_hpcn_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Wed Aug 29 16:16:23 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:58 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_PPC_STD_MMU_32=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -64,12 +69,14 @@ CONFIG_BSD_PROCESS_ACCT=y # CONFIG_BSD_PROCESS_ACCT_V3 is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set CONFIG_AUDIT=y # CONFIG_AUDITSYSCALL is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -90,7 +97,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -131,7 +137,6 @@ CONFIG_DEFAULT_IOSCHED="cfq" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set CONFIG_PPC_86xx=y @@ -141,6 +146,7 @@ CONFIG_PPC_86xx=y # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PQ2ADS is not set CONFIG_MPC8641_HPCN=y +# CONFIG_MPC8610_HPCD is not set CONFIG_MPC8641=y CONFIG_MPIC=y # CONFIG_MPIC_WEIRD is not set @@ -159,6 +165,10 @@ CONFIG_FSL_ULI1575=y # Kernel options # CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set @@ -181,6 +191,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -207,11 +218,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -226,7 +234,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -275,6 +283,7 @@ CONFIG_INET_TUNNEL=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -319,10 +328,6 @@ CONFIG_SCTP_HMAC_MD5=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -352,6 +357,7 @@ CONFIG_FIB_RULES=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -424,6 +430,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -435,6 +442,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -502,6 +510,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -516,14 +525,7 @@ CONFIG_PATA_ALI=y # CONFIG_PATA_WINBOND is not set # CONFIG_PATA_PLATFORM is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -539,6 +541,8 @@ CONFIG_DUMMY=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -555,6 +559,7 @@ CONFIG_VITESSE_PHY=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -563,11 +568,17 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -575,6 +586,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -585,11 +597,14 @@ CONFIG_GFAR_NAPI=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -605,7 +620,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -632,7 +646,6 @@ CONFIG_INPUT=y # # CONFIG_INPUT_MOUSEDEV is not set # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -692,15 +705,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_NVRAM=y CONFIG_GEN_RTC=y CONFIG_GEN_RTC_X=y # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -769,6 +779,13 @@ CONFIG_SENSORS_EEPROM=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -863,6 +880,7 @@ CONFIG_DVB_CAPTURE_DRIVERS=y # CONFIG_DVB_OR51132 is not set # CONFIG_DVB_BCM3510 is not set # CONFIG_DVB_LGDT330X is not set +# CONFIG_DVB_S5H1409 is not set # # Tuners/PLL support @@ -872,6 +890,9 @@ CONFIG_DVB_CAPTURE_DRIVERS=y # CONFIG_DVB_TDA827X is not set # CONFIG_DVB_TUNER_QT1010 is not set # CONFIG_DVB_TUNER_MT2060 is not set +# CONFIG_DVB_TUNER_MT2266 is not set +# CONFIG_DVB_TUNER_MT2131 is not set +# CONFIG_DVB_TUNER_DIB0070 is not set # # Miscellaneous devices @@ -885,16 +906,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -1026,6 +1048,7 @@ CONFIG_AC97_BUS=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1086,6 +1109,7 @@ CONFIG_USB_STORAGE=y # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set @@ -1166,6 +1190,7 @@ CONFIG_RTC_INTF_DEV=y # I2C RTC drivers # # CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set # CONFIG_RTC_DRV_MAX6900 is not set # CONFIG_RTC_DRV_RS5C372 is not set @@ -1195,19 +1220,6 @@ CONFIG_RTC_DRV_CMOS=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1224,7 +1236,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1273,7 +1284,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1296,10 +1306,7 @@ CONFIG_SYSV_FS=m CONFIG_UFS_FS=m # CONFIG_UFS_FS_WRITE is not set # CONFIG_UFS_DEBUG is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -1345,10 +1352,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_CODEPAGE_437 is not set @@ -1389,10 +1392,6 @@ CONFIG_NLS_DEFAULT="iso8859-1" # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1411,17 +1410,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set -# CONFIG_KPROBES is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set @@ -1446,9 +1441,12 @@ CONFIG_SCHED_DEBUG=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1461,6 +1459,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1471,7 +1470,7 @@ CONFIG_CRYPTO_HMAC=y # CONFIG_CRYPTO_NULL is not set # CONFIG_CRYPTO_MD4 is not set CONFIG_CRYPTO_MD5=y -# CONFIG_CRYPTO_SHA1 is not set +CONFIG_CRYPTO_SHA1=m # CONFIG_CRYPTO_SHA256 is not set # CONFIG_CRYPTO_SHA512 is not set # CONFIG_CRYPTO_WP512 is not set @@ -1481,6 +1480,7 @@ CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1494,9 +1494,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/mpc866_ads_defconfig b/arch/powerpc/configs/mpc866_ads_defconfig index 070b0a5b9c0d..a7ef231f2ab2 100644 --- a/arch/powerpc/configs/mpc866_ads_defconfig +++ b/arch/powerpc/configs/mpc866_ads_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:44 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:48:59 2007 # # CONFIG_PPC64 is not set @@ -18,8 +18,13 @@ CONFIG_8xx=y # CONFIG_PPC_MM_SLICES is not set CONFIG_NOT_COHERENT_CACHE=y CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -58,9 +63,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set # CONFIG_BLK_DEV_INITRD is not set @@ -79,7 +87,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y # CONFIG_EPOLL is not set CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y # CONFIG_VM_EVENT_COUNTERS is not set @@ -121,6 +128,7 @@ CONFIG_CPM1=y # CONFIG_MPC8XXFADS is not set CONFIG_MPC86XADS=y # CONFIG_MPC885ADS is not set +# CONFIG_PPC_EP88XC is not set # # MPC8xx CPM Options @@ -131,6 +139,7 @@ CONFIG_MPC86XADS=y # CONFIG_8xx_COPYBACK=y CONFIG_8xx_CPU6=y +CONFIG_8xx_CPU15=y CONFIG_NO_UCODE_PATCH=y # CONFIG_USB_SOF_UCODE_PATCH is not set # CONFIG_I2C_SPI_UCODE_PATCH is not set @@ -148,11 +157,16 @@ CONFIG_NO_UCODE_PATCH=y # CONFIG_CPU_FREQ is not set # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set +CONFIG_CPM=y # # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set @@ -174,6 +188,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -182,8 +197,11 @@ CONFIG_VIRT_TO_BUS=y # CONFIG_PROC_DEVICETREE is not set # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_SECCOMP is not set -# CONFIG_WANT_DEVICE_TREE is not set +CONFIG_WANT_DEVICE_TREE=y +CONFIG_DEVICE_TREE="" CONFIG_ISA_DMA_API=y # @@ -198,10 +216,6 @@ CONFIG_FSL_SOC=y # CONFIG_ARCH_SUPPORTS_MSI is not set # -# PCCARD (PCMCIA/CardBus) support -# - -# # Advanced setup # # CONFIG_ADVANCED_OPTIONS is not set @@ -213,7 +227,7 @@ CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_TASK_SIZE=0x80000000 -CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_START=0xfd000000 CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_BOOT_LOAD=0x00400000 @@ -254,6 +268,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -279,10 +294,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -348,6 +359,7 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set CONFIG_PHYLIB=y # @@ -365,11 +377,20 @@ CONFIG_PHYLIB=y CONFIG_FIXED_PHY=y CONFIG_FIXED_MII_10_FDX=y CONFIG_FIXED_MII_100_FDX=y +# CONFIG_FIXED_MII_1000_FDX is not set +CONFIG_FIXED_MII_AMNT=1 +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set CONFIG_FS_ENET=y CONFIG_FS_ENET_HAS_SCC=y CONFIG_FS_ENET_HAS_FEC=y +CONFIG_FS_ENET_MDIO_FEC=y CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y @@ -403,7 +424,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -470,7 +490,6 @@ CONFIG_SERIAL_CPM_SMC2=y CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y @@ -489,9 +508,8 @@ CONFIG_GEN_RTC=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_IT87 is not set # CONFIG_SENSORS_PC87360 is not set # CONFIG_SENSORS_PC87427 is not set @@ -501,6 +519,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -517,16 +542,15 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -535,6 +559,7 @@ CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set CONFIG_USB_SUPPORT=y # CONFIG_USB_ARCH_HAS_HCD is not set # CONFIG_USB_ARCH_HAS_OHCI is not set @@ -554,19 +579,6 @@ CONFIG_USB_SUPPORT=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -585,7 +597,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -626,7 +637,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -645,10 +655,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -690,15 +697,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -717,22 +716,21 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_SAMPLES is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -740,4 +738,7 @@ CONFIG_ENABLE_MUST_CHECK=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/mpc885_ads_defconfig b/arch/powerpc/configs/mpc885_ads_defconfig index 482d99db6870..22f8171d6d45 100644 --- a/arch/powerpc/configs/mpc885_ads_defconfig +++ b/arch/powerpc/configs/mpc885_ads_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc3 -# Mon Aug 27 15:23:16 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:01 2007 # # CONFIG_PPC64 is not set @@ -18,8 +18,13 @@ CONFIG_8xx=y # CONFIG_PPC_MM_SLICES is not set CONFIG_NOT_COHERENT_CACHE=y CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -59,9 +64,12 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set # CONFIG_BLK_DEV_INITRD is not set @@ -81,7 +89,6 @@ CONFIG_BUG=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y # CONFIG_VM_EVENT_COUNTERS is not set @@ -158,11 +165,17 @@ CONFIG_NO_UCODE_PATCH=y # CONFIG_CPU_FREQ is not set # CONFIG_CPM2 is not set CONFIG_PPC_CPM_NEW_BINDING=y +# CONFIG_FSL_ULI1575 is not set +CONFIG_CPM=y # # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y CONFIG_HZ_100=y # CONFIG_HZ_250 is not set # CONFIG_HZ_300 is not set @@ -174,6 +187,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set # CONFIG_MATH_EMULATION is not set +CONFIG_8XX_MINIMAL_FPEMU=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y CONFIG_ARCH_FLATMEM_ENABLE=y CONFIG_ARCH_POPULATES_NODE_MAP=y @@ -184,6 +198,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -192,6 +207,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_SECCOMP is not set CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="mpc885ads.dts" @@ -207,10 +224,6 @@ CONFIG_FSL_SOC=y # CONFIG_PCI_SYSCALL is not set # CONFIG_PCI_QSPAN is not set # CONFIG_ARCH_SUPPORTS_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # @@ -225,7 +238,7 @@ CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 CONFIG_TASK_SIZE=0x80000000 -CONFIG_CONSISTENT_START=0xff100000 +CONFIG_CONSISTENT_START=0xfd000000 CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_BOOT_LOAD=0x00400000 @@ -262,6 +275,7 @@ CONFIG_SYN_COOKIES=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -287,10 +301,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -319,6 +329,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -342,6 +353,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -425,6 +437,7 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set CONFIG_PHYLIB=y # @@ -443,9 +456,15 @@ CONFIG_DAVICOM_PHY=y # CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FEC=y +CONFIG_FS_ENET_MDIO_FEC=y # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set @@ -503,7 +522,6 @@ CONFIG_SERIAL_CPM_SMC2=y CONFIG_UNIX98_PTYS=y # CONFIG_LEGACY_PTYS is not set # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y @@ -521,6 +539,13 @@ CONFIG_GEN_RTC=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -537,16 +562,15 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -# CONFIG_VIDEO_OUTPUT_CONTROL is not set -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -559,19 +583,6 @@ CONFIG_DAB=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -620,7 +631,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -640,10 +650,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -685,15 +692,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -710,16 +709,13 @@ CONFIG_ZLIB_INFLATE=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -741,8 +737,11 @@ CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -755,4 +754,7 @@ CONFIG_FORCED_INLINING=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/pasemi_defconfig b/arch/powerpc/configs/pasemi_defconfig index 78c968aade4e..292de3d6ce92 100644 --- a/arch/powerpc/configs/pasemi_defconfig +++ b/arch/powerpc/configs/pasemi_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.24-rc2 -# Tue Nov 6 23:23:50 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:03 2007 # CONFIG_PPC64=y @@ -68,6 +68,7 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=17 @@ -211,6 +212,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y # CONFIG_BINFMT_MISC is not set CONFIG_FORCE_MAX_ZONEORDER=9 +CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y CONFIG_IOMMU_VMERGE=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y # CONFIG_KEXEC is not set @@ -774,7 +776,6 @@ CONFIG_PASEMI_MAC=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_NET_PCMCIA is not set # CONFIG_WAN is not set @@ -958,6 +959,7 @@ CONFIG_HWMON_VID=y # CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set # CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_F75375S is not set diff --git a/arch/powerpc/configs/pmac32_defconfig b/arch/powerpc/configs/pmac32_defconfig index 8e5988c4a164..5416be4419bb 100644 --- a/arch/powerpc/configs/pmac32_defconfig +++ b/arch/powerpc/configs/pmac32_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:44:46 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:05 2007 # # CONFIG_PPC64 is not set @@ -21,8 +21,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,10 +68,15 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -87,7 +97,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -127,7 +136,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -141,6 +149,7 @@ CONFIG_PPC_PMAC=y # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PQ2ADS is not set +# CONFIG_EMBEDDED6xx is not set CONFIG_PPC_NATIVE=y CONFIG_MPIC=y # CONFIG_MPIC_WEIRD is not set @@ -158,6 +167,8 @@ CONFIG_CPU_FREQ_STAT=y # CONFIG_CPU_FREQ_STAT_DETAILS is not set CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set CONFIG_CPU_FREQ_GOV_PERFORMANCE=y CONFIG_CPU_FREQ_GOV_POWERSAVE=y CONFIG_CPU_FREQ_GOV_USERSPACE=y @@ -177,6 +188,10 @@ CONFIG_PPC601_SYNC_FIX=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -198,6 +213,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -210,7 +226,9 @@ CONFIG_PM=y CONFIG_PM_DEBUG=y # CONFIG_PM_VERBOSE is not set CONFIG_PM_SLEEP=y +CONFIG_SUSPEND_UP_POSSIBLE=y CONFIG_SUSPEND=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_HIBERNATION=y CONFIG_PM_STD_PARTITION="" CONFIG_APM_EMULATION=y @@ -230,11 +248,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# CONFIG_PCCARD=m # CONFIG_PCMCIA_DEBUG is not set CONFIG_PCMCIA=m @@ -267,7 +282,7 @@ CONFIG_PCCARD_NONSTATIC=m CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00800000 # @@ -305,6 +320,7 @@ CONFIG_INET_ESP=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -372,6 +388,7 @@ CONFIG_NETFILTER_XT_MATCH_SCTP=m # CONFIG_NETFILTER_XT_MATCH_STATISTIC is not set CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m +CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m # CONFIG_NETFILTER_XT_MATCH_HASHLIMIT is not set @@ -448,13 +465,9 @@ CONFIG_IP_DCCP_CCID3_RTO=100 # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set -CONFIG_NET_SCH_FIFO=y CONFIG_NET_CLS_ROUTE=y +CONFIG_NET_SCH_FIFO=y # # Network testing @@ -492,6 +505,8 @@ CONFIG_IRTTY_SIR=m # # CONFIG_DONGLE is not set # CONFIG_KINGSUN_DONGLE is not set +# CONFIG_KSDAZZLE_DONGLE is not set +# CONFIG_KS959_DONGLE is not set # # Old SIR device drivers @@ -545,8 +560,10 @@ CONFIG_BT_HCIBFUSB=m # Wireless # CONFIG_CFG80211=m +CONFIG_NL80211=y CONFIG_WIRELESS_EXT=y CONFIG_MAC80211=m +CONFIG_MAC80211_RCSIMPLE=y CONFIG_MAC80211_LEDS=y # CONFIG_MAC80211_DEBUG is not set CONFIG_IEEE80211=m @@ -565,6 +582,7 @@ CONFIG_IEEE80211_CRYPT_TKIP=m # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" # CONFIG_STANDALONE is not set CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -622,6 +640,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # # CONFIG_IDE_GENERIC is not set +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -629,8 +652,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set @@ -661,7 +682,7 @@ CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y CONFIG_BLK_DEV_IDEDMA_PMAC=y # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -702,6 +723,7 @@ CONFIG_SCSI_FC_ATTRS=y # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -718,6 +740,7 @@ CONFIG_SCSI_AIC7XXX_OLD=m # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -769,14 +792,8 @@ CONFIG_DM_MIRROR=m CONFIG_DM_ZERO=m # CONFIG_DM_MULTIPATH is not set # CONFIG_DM_DELAY is not set - -# -# Fusion MPT device support -# +# CONFIG_DM_UEVENT is not set # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -830,6 +847,8 @@ CONFIG_DUMMY=m # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -843,6 +862,10 @@ CONFIG_SUNGEM=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y CONFIG_PCNET32=y # CONFIG_PCNET32_NAPI is not set @@ -850,7 +873,6 @@ CONFIG_PCNET32=y # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set # CONFIG_E100 is not set # CONFIG_FEALNX is not set @@ -868,6 +890,7 @@ CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -875,6 +898,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -884,11 +908,14 @@ CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -907,15 +934,41 @@ CONFIG_APPLE_AIRPORT=m # CONFIG_TMD_HERMES is not set # CONFIG_NORTEL_HERMES is not set CONFIG_PCI_HERMES=m -# CONFIG_ATMEL is not set CONFIG_PCMCIA_HERMES=m # CONFIG_PCMCIA_SPECTRUM is not set +# CONFIG_ATMEL is not set # CONFIG_AIRO_CS is not set # CONFIG_PCMCIA_WL3501 is not set CONFIG_PRISM54=m # CONFIG_USB_ZD1201 is not set # CONFIG_RTL8187 is not set +# CONFIG_ADM8211 is not set +CONFIG_P54_COMMON=m +# CONFIG_P54_USB is not set +# CONFIG_P54_PCI is not set +# CONFIG_IWLWIFI is not set # CONFIG_HOSTAP is not set +CONFIG_B43=m +CONFIG_B43_PCI_AUTOSELECT=y +CONFIG_B43_PCICORE_AUTOSELECT=y +# CONFIG_B43_PCMCIA is not set +CONFIG_B43_LEDS=y +# CONFIG_B43_DEBUG is not set +CONFIG_B43_DMA=y +CONFIG_B43_PIO=y +CONFIG_B43_DMA_AND_PIO_MODE=y +# CONFIG_B43_DMA_MODE is not set +# CONFIG_B43_PIO_MODE is not set +CONFIG_B43LEGACY=m +CONFIG_B43LEGACY_PCI_AUTOSELECT=y +CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y +CONFIG_B43LEGACY_DEBUG=y +CONFIG_B43LEGACY_DMA=y +CONFIG_B43LEGACY_PIO=y +CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y +# CONFIG_B43LEGACY_DMA_MODE is not set +# CONFIG_B43LEGACY_PIO_MODE is not set +# CONFIG_RT2X00 is not set # # USB Network Adapters @@ -924,7 +977,6 @@ CONFIG_PRISM54=m # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -CONFIG_USB_USBNET_MII=m CONFIG_USB_USBNET=m CONFIG_USB_NET_AX8817X=m CONFIG_USB_NET_CDCETHER=m @@ -975,7 +1027,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set @@ -1034,29 +1085,19 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4 # CONFIG_SERIAL_UARTLITE is not set CONFIG_SERIAL_CORE=m CONFIG_SERIAL_PMACZILOG=m +CONFIG_SERIAL_PMACZILOG_TTYS=y # CONFIG_SERIAL_JSM is not set # CONFIG_SERIAL_OF_PLATFORM is not set CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set -# CONFIG_HW_RANDOM is not set +CONFIG_HW_RANDOM=m CONFIG_NVRAM=y CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -CONFIG_AGP=m -CONFIG_AGP_UNINORTH=m -CONFIG_DRM=m -# CONFIG_DRM_TDFX is not set -CONFIG_DRM_R128=m -CONFIG_DRM_RADEON=m -# CONFIG_DRM_MGA is not set -# CONFIG_DRM_SIS is not set -# CONFIG_DRM_VIA is not set -# CONFIG_DRM_SAVAGE is not set # # PCMCIA character devices @@ -1138,6 +1179,20 @@ CONFIG_APM_POWER=y # CONFIG_BATTERY_DS2760 is not set CONFIG_BATTERY_PMU=y # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +CONFIG_SSB=m +CONFIG_SSB_PCIHOST_POSSIBLE=y +CONFIG_SSB_PCIHOST=y +CONFIG_SSB_PCMCIAHOST_POSSIBLE=y +# CONFIG_SSB_PCMCIAHOST is not set +# CONFIG_SSB_DEBUG is not set +CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y +CONFIG_SSB_DRIVER_PCICORE=y # # Multifunction device drivers @@ -1154,18 +1209,16 @@ CONFIG_BATTERY_PMU=y # # Graphics support # -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_LCD_CLASS_DEVICE=m -CONFIG_BACKLIGHT_CLASS_DEVICE=y - -# -# Display device support -# -CONFIG_DISPLAY_SUPPORT=y - -# -# Display hardware drivers -# +CONFIG_AGP=m +CONFIG_AGP_UNINORTH=m +CONFIG_DRM=m +# CONFIG_DRM_TDFX is not set +CONFIG_DRM_R128=m +CONFIG_DRM_RADEON=m +# CONFIG_DRM_MGA is not set +# CONFIG_DRM_SIS is not set +# CONFIG_DRM_VIA is not set +# CONFIG_DRM_SAVAGE is not set CONFIG_VGASTATE=y # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y @@ -1174,6 +1227,7 @@ CONFIG_FB_DDC=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set @@ -1199,6 +1253,7 @@ CONFIG_FB_CT65550=y # CONFIG_FB_ASILIANT is not set CONFIG_FB_IMSTT=y # CONFIG_FB_VGA16 is not set +# CONFIG_FB_UVESA is not set # CONFIG_FB_S1D13XXX is not set CONFIG_FB_NVIDIA=y CONFIG_FB_NVIDIA_I2C=y @@ -1236,6 +1291,19 @@ CONFIG_FB_3DFX=y # CONFIG_FB_PM3 is not set # CONFIG_FB_IBM_GXT4500 is not set # CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set + +# +# Display device support +# +CONFIG_DISPLAY_SUPPORT=y + +# +# Display hardware drivers +# # # Console display driver support @@ -1399,6 +1467,7 @@ CONFIG_SND_USB_AUDIO=m CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1488,6 +1557,7 @@ CONFIG_USB_SERIAL=m # CONFIG_USB_SERIAL_AIRPRIME is not set # CONFIG_USB_SERIAL_ARK3116 is not set # CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_CH341 is not set # CONFIG_USB_SERIAL_WHITEHEAT is not set # CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set # CONFIG_USB_SERIAL_CP2101 is not set @@ -1587,19 +1657,6 @@ CONFIG_LEDS_TRIGGER_IDE_DISK=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1616,7 +1673,6 @@ CONFIG_EXT3_FS_POSIX_ACL=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1663,7 +1719,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1682,10 +1737,7 @@ CONFIG_HFSPLUS_FS=m # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1735,10 +1787,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=m @@ -1779,10 +1827,6 @@ CONFIG_NLS_ISO8859_1=m # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set CONFIG_NLS_UTF8=m - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1806,18 +1850,17 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y CONFIG_PROFILING=y CONFIG_OPROFILE=y # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1841,9 +1884,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set # CONFIG_FORCED_INLINING is not set +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set CONFIG_DEBUGGER=y @@ -1859,6 +1905,7 @@ CONFIG_BOOTX_TEXT=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1879,6 +1926,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1893,9 +1941,12 @@ CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m +# CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/ppc64_defconfig b/arch/powerpc/configs/ppc64_defconfig index 3e90c835fe12..5760b9f033ea 100644 --- a/arch/powerpc/configs/ppc64_defconfig +++ b/arch/powerpc/configs/ppc64_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.24-rc2 -# Tue Nov 6 23:43:56 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:07 2007 # CONFIG_PPC64=y @@ -73,6 +73,7 @@ CONFIG_TASKSTATS=y CONFIG_TASK_DELAY_ACCT=y # CONFIG_TASK_XACCT is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y @@ -80,11 +81,11 @@ CONFIG_LOG_BUF_SHIFT=17 CONFIG_CGROUPS=y # CONFIG_CGROUP_DEBUG is not set # CONFIG_CGROUP_NS is not set -# CONFIG_CGROUP_CPUACCT is not set CONFIG_CPUSETS=y CONFIG_FAIR_GROUP_SCHED=y CONFIG_FAIR_USER_SCHED=y # CONFIG_FAIR_CGROUP_SCHED is not set +# CONFIG_CGROUP_CPUACCT is not set CONFIG_SYSFS_DEPRECATED=y CONFIG_PROC_PID_CPUSET=y CONFIG_RELAY=y @@ -258,6 +259,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m CONFIG_FORCE_MAX_ZONEORDER=13 +CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y CONFIG_IOMMU_VMERGE=y CONFIG_HOTPLUG_CPU=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -955,7 +957,6 @@ CONFIG_IBMOL=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_NET_PCMCIA is not set # CONFIG_WAN is not set diff --git a/arch/powerpc/configs/pq2fads_defconfig b/arch/powerpc/configs/pq2fads_defconfig index 9191f557b044..142d206d6870 100644 --- a/arch/powerpc/configs/pq2fads_defconfig +++ b/arch/powerpc/configs/pq2fads_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 11:58:17 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:09 2007 # # CONFIG_PPC64 is not set @@ -20,8 +20,13 @@ CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set # CONFIG_SMP is not set CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,6 +68,8 @@ CONFIG_SYSVIPC_SYSCTL=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set # CONFIG_SYSFS_DEPRECATED is not set # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -82,7 +89,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -116,7 +122,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # # CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_EMBEDDED6xx is not set CONFIG_PPC_82xx=y # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -126,7 +131,6 @@ CONFIG_PPC_82xx=y # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_MPC8272_ADS is not set CONFIG_PQ2FADS=y -# CONFIG_EP8248E is not set CONFIG_PQ2ADS=y CONFIG_8260=y CONFIG_PQ2_ADS_PCI_PIC=y @@ -149,6 +153,10 @@ CONFIG_CPM=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -165,6 +173,7 @@ CONFIG_ARCH_POPULATES_NODE_MAP=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -173,6 +182,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y CONFIG_SECCOMP=y CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="pq2fads.dts" @@ -192,11 +203,8 @@ CONFIG_PCI_8260=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # @@ -210,7 +218,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_BOOT_LOAD=0x00400000 # @@ -247,6 +255,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -290,10 +299,6 @@ CONFIG_NETFILTER=y # CONFIG_LLC2 is not set # CONFIG_IPX is not set # CONFIG_ATALK is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -319,6 +324,7 @@ CONFIG_NETFILTER=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -342,6 +348,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -380,6 +387,7 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_PHYSMAP is not set CONFIG_MTD_PHYSMAP_OF=y # CONFIG_MTD_SBC8240 is not set +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -442,10 +450,40 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # # CONFIG_IDE_GENERIC is not set -# CONFIG_BLK_DEV_IDEPCI is not set +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# # CONFIG_IDEPCI_PCIBUS_ORDER is not set +# CONFIG_BLK_DEV_GENERIC is not set +# CONFIG_BLK_DEV_AEC62XX is not set +# CONFIG_BLK_DEV_ALI15X3 is not set +# CONFIG_BLK_DEV_AMD74XX is not set +# CONFIG_BLK_DEV_CMD64X is not set +# CONFIG_BLK_DEV_TRIFLEX is not set +# CONFIG_BLK_DEV_CY82C693 is not set +# CONFIG_BLK_DEV_CS5530 is not set +# CONFIG_BLK_DEV_HPT34X is not set +# CONFIG_BLK_DEV_HPT366 is not set +# CONFIG_BLK_DEV_JMICRON is not set +# CONFIG_BLK_DEV_SC1200 is not set +# CONFIG_BLK_DEV_PIIX is not set +# CONFIG_BLK_DEV_IT8213 is not set +# CONFIG_BLK_DEV_IT821X is not set +# CONFIG_BLK_DEV_NS87415 is not set +# CONFIG_BLK_DEV_PDC202XX_OLD is not set +# CONFIG_BLK_DEV_PDC202XX_NEW is not set +# CONFIG_BLK_DEV_SVWKS is not set +# CONFIG_BLK_DEV_SIIMAGE is not set +# CONFIG_BLK_DEV_SL82C105 is not set +# CONFIG_BLK_DEV_SLC90E66 is not set +# CONFIG_BLK_DEV_TRM290 is not set +# CONFIG_BLK_DEV_VIA82CXXX is not set +# CONFIG_BLK_DEV_TC86C001 is not set # CONFIG_IDE_ARM is not set # CONFIG_BLK_DEV_IDEDMA is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -457,10 +495,6 @@ CONFIG_IDE_PROC_FS=y # CONFIG_SCSI_NETLINK is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set # @@ -479,6 +513,7 @@ CONFIG_NETDEVICES=y # CONFIG_BONDING is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=y +# CONFIG_VETH is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -504,20 +539,28 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set # CONFIG_NET_PCI is not set +# CONFIG_B44 is not set CONFIG_FS_ENET=y # CONFIG_FS_ENET_HAS_SCC is not set CONFIG_FS_ENET_HAS_FCC=y +# CONFIG_FS_ENET_MDIO_FCC is not set CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_R8169 is not set # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -525,11 +568,14 @@ CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -567,7 +613,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_EVBUG is not set @@ -638,14 +683,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set CONFIG_HW_RANDOM=y # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set CONFIG_DEVPORT=y # CONFIG_I2C is not set @@ -658,6 +700,13 @@ CONFIG_DEVPORT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -674,16 +723,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -707,6 +757,7 @@ CONFIG_USB_GADGET=y # CONFIG_USB_GADGET_DEBUG_FILES is not set CONFIG_USB_GADGET_SELECTED=y # CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set # CONFIG_USB_GADGET_FSL_USB2 is not set # CONFIG_USB_GADGET_NET2280 is not set # CONFIG_USB_GADGET_PXA2XX is not set @@ -731,19 +782,6 @@ CONFIG_USB_ETH=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -759,7 +797,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_POSIX_ACL is not set # CONFIG_EXT3_FS_SECURITY is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -799,7 +836,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # # Miscellaneous filesystems @@ -812,10 +848,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -853,10 +886,6 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -915,11 +944,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -943,8 +974,11 @@ CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -952,16 +986,6 @@ CONFIG_FORCED_INLINING=y # CONFIG_KGDB_CONSOLE is not set CONFIG_BDI_SWITCH=y # CONFIG_PPC_EARLY_DEBUG is not set -# CONFIG_PPC_EARLY_DEBUG_LPAR is not set -# CONFIG_PPC_EARLY_DEBUG_G5 is not set -# CONFIG_PPC_EARLY_DEBUG_RTAS_PANEL is not set -# CONFIG_PPC_EARLY_DEBUG_RTAS_CONSOLE is not set -# CONFIG_PPC_EARLY_DEBUG_MAPLE is not set -# CONFIG_PPC_EARLY_DEBUG_ISERIES is not set -# CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set -# CONFIG_PPC_EARLY_DEBUG_BEAT is not set -# CONFIG_PPC_EARLY_DEBUG_44x is not set -# CONFIG_PPC_EARLY_DEBUG_CPM is not set # # Security options @@ -997,8 +1021,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set +CONFIG_PPC_LIB_RHEAP=y diff --git a/arch/powerpc/configs/prpmc2800_defconfig b/arch/powerpc/configs/prpmc2800_defconfig index 3e87faf9b5c2..46b2579d38b1 100644 --- a/arch/powerpc/configs/prpmc2800_defconfig +++ b/arch/powerpc/configs/prpmc2800_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Tue Aug 28 21:24:45 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:11 2007 # # CONFIG_PPC64 is not set @@ -15,6 +15,7 @@ CONFIG_6xx=y # CONFIG_44x is not set # CONFIG_E200 is not set CONFIG_PPC_FPU=y +CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y CONFIG_PPC_STD_MMU_32=y # CONFIG_PPC_MM_SLICES is not set @@ -22,8 +23,13 @@ CONFIG_PPC_STD_MMU_32=y CONFIG_NOT_COHERENT_CACHE=y CONFIG_CHECK_CACHE_COHERENCY=y CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -63,9 +69,12 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set # CONFIG_SYSFS_DEPRECATED is not set # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -85,7 +94,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -119,16 +127,21 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # # Platform support # -# CONFIG_PPC_MULTIPLATFORM is not set -CONFIG_EMBEDDED6xx=y +CONFIG_PPC_MULTIPLATFORM=y # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set +CONFIG_CLASSIC32=y +# CONFIG_PPC_CHRP is not set # CONFIG_PPC_MPC52xx is not set # CONFIG_PPC_MPC5200 is not set +# CONFIG_PPC_EFIKA is not set +# CONFIG_PPC_LITE5200 is not set +# CONFIG_PPC_PMAC is not set # CONFIG_PPC_CELL is not set # CONFIG_PPC_CELL_NATIVE is not set # CONFIG_PQ2ADS is not set +CONFIG_EMBEDDED6xx=y # CONFIG_LINKSTATION is not set # CONFIG_MPC7448HPC2 is not set # CONFIG_PPC_HOLLY is not set @@ -144,6 +157,7 @@ CONFIG_MV64X60=y # CONFIG_PPC_INDIRECT_IO is not set # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set +# CONFIG_TAU is not set # CONFIG_CPM2 is not set # CONFIG_FSL_ULI1575 is not set @@ -151,6 +165,10 @@ CONFIG_MV64X60=y # Kernel options # CONFIG_HIGHMEM=y +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -172,6 +190,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 # CONFIG_RESOURCES_64BIT is not set CONFIG_ZONE_DMA_FLAG=1 @@ -180,6 +199,8 @@ CONFIG_VIRT_TO_BUS=y CONFIG_PROC_DEVICETREE=y # CONFIG_CMDLINE_BOOL is not set # CONFIG_PM is not set +CONFIG_SUSPEND_UP_POSSIBLE=y +CONFIG_HIBERNATION_UP_POSSIBLE=y # CONFIG_SECCOMP is not set CONFIG_WANT_DEVICE_TREE=y CONFIG_DEVICE_TREE="prpmc2800.dts" @@ -197,10 +218,7 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# +CONFIG_PCI_LEGACY=y # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -215,7 +233,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_CONSISTENT_START=0xff100000 CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_BOOT_LOAD=0x00800000 @@ -257,6 +275,7 @@ CONFIG_SYN_COOKIES=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -282,10 +301,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -314,6 +329,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y # CONFIG_FW_LOADER is not set @@ -337,6 +353,7 @@ CONFIG_MTD_BLOCK=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -369,6 +386,7 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_COMPLEX_MAPPINGS is not set # CONFIG_MTD_PHYSMAP is not set CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -438,6 +456,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y # CONFIG_IDEPCI_SHARE_IRQ is not set CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -445,8 +468,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set # CONFIG_BLK_DEV_AMD74XX is not set @@ -474,7 +495,7 @@ CONFIG_BLK_DEV_PDC202XX_NEW=y # CONFIG_BLK_DEV_TC86C001 is not set # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -512,6 +533,7 @@ CONFIG_BLK_DEV_SD=y # CONFIG_SCSI_FC_ATTRS is not set # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -523,6 +545,7 @@ CONFIG_SCSI_LOWLEVEL=y # CONFIG_SCSI_AIC79XX is not set # CONFIG_SCSI_AIC94XX is not set # CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_ADVANSYS is not set # CONFIG_SCSI_ARCMSR is not set # CONFIG_MEGARAID_NEWGEN is not set # CONFIG_MEGARAID_LEGACY is not set @@ -590,6 +613,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -603,14 +627,7 @@ CONFIG_SATA_MV=y # CONFIG_PATA_VIA is not set # CONFIG_PATA_WINBOND is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -628,6 +645,8 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set CONFIG_PHYLIB=y @@ -644,6 +663,7 @@ CONFIG_PHYLIB=y # CONFIG_BROADCOM_PHY is not set # CONFIG_ICPLUS_PHY is not set # CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set CONFIG_NET_ETHERNET=y CONFIG_MII=y # CONFIG_HAPPYMEAL is not set @@ -652,13 +672,16 @@ CONFIG_MII=y # CONFIG_NET_VENDOR_3COM is not set # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y # CONFIG_PCNET32 is not set # CONFIG_AMD8111_ETH is not set # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=y # CONFIG_FEALNX is not set @@ -682,6 +705,7 @@ CONFIG_NETDEV_1000=y CONFIG_E1000=y # CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -689,6 +713,7 @@ CONFIG_E1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -698,11 +723,14 @@ CONFIG_MV643XX_ETH=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -718,7 +746,6 @@ CONFIG_NETDEV_10000=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -748,7 +775,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -795,15 +821,12 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -873,8 +896,6 @@ CONFIG_I2C_MV64XXX=y # CONFIG_POWER_SUPPLY is not set CONFIG_HWMON=y # CONFIG_HWMON_VID is not set -# CONFIG_SENSORS_ABITUGURU is not set -# CONFIG_SENSORS_ABITUGURU3 is not set # CONFIG_SENSORS_AD7418 is not set # CONFIG_SENSORS_ADM1021 is not set # CONFIG_SENSORS_ADM1025 is not set @@ -882,12 +903,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADM1029 is not set # CONFIG_SENSORS_ADM1031 is not set # CONFIG_SENSORS_ADM9240 is not set -# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set -# CONFIG_SENSORS_FSCHER is not set -# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set # CONFIG_SENSORS_GL518SM is not set # CONFIG_SENSORS_GL520SM is not set # CONFIG_SENSORS_IT87 is not set @@ -923,6 +945,13 @@ CONFIG_HWMON=y # CONFIG_SENSORS_W83627HF is not set # CONFIG_SENSORS_W83627EHF is not set # CONFIG_HWMON_DEBUG_CHIP is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -939,16 +968,17 @@ CONFIG_HWMON=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=y +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=y -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Console display driver support @@ -964,6 +994,7 @@ CONFIG_DUMMY_CONSOLE=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1091,6 +1122,7 @@ CONFIG_RTC_INTF_DEV=y # I2C RTC drivers # # CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set # CONFIG_RTC_DRV_DS1672 is not set CONFIG_RTC_DRV_MAX6900=y # CONFIG_RTC_DRV_RS5C372 is not set @@ -1120,19 +1152,6 @@ CONFIG_RTC_DRV_MAX6900=y # # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -1149,7 +1168,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -1190,7 +1208,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -1210,10 +1227,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y # CONFIG_NFS_V3 is not set # CONFIG_NFS_V4 is not set @@ -1253,15 +1267,7 @@ CONFIG_MSDOS_PARTITION=y # CONFIG_KARMA_PARTITION is not set # CONFIG_EFI_PARTITION is not set # CONFIG_SYSV68_PARTITION is not set - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1279,23 +1285,23 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y # CONFIG_MAGIC_SYSRQ is not set # CONFIG_UNUSED_SYMBOLS is not set # CONFIG_DEBUG_FS is not set # CONFIG_HEADERS_CHECK is not set # CONFIG_DEBUG_KERNEL is not set +# CONFIG_SLUB_DEBUG_ON is not set CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_SAMPLES is not set +# CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set # @@ -1303,4 +1309,6 @@ CONFIG_DEBUG_BUGVERBOSE=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set # CONFIG_CRYPTO is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/ps3_defconfig b/arch/powerpc/configs/ps3_defconfig index 3566c448bdc0..5bd547ecd60a 100644 --- a/arch/powerpc/configs/ps3_defconfig +++ b/arch/powerpc/configs/ps3_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc2 -# Tue Aug 7 19:17:26 2007 +# Linux kernel version: 2.6.24-rc4 +# Tue Dec 4 22:49:57 2007 # CONFIG_PPC64=y @@ -11,6 +11,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY is not set CONFIG_POWER3=y CONFIG_POWER4=y +CONFIG_TUNE_CELL=y CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y @@ -19,8 +20,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -59,14 +65,18 @@ CONFIG_LOCALVERSION_AUTO=y CONFIG_SWAP=y CONFIG_SYSVIPC=y CONFIG_SYSVIPC_SYSCTL=y -# CONFIG_POSIX_MQUEUE is not set +CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=17 -# CONFIG_CPUSETS is not set +# CONFIG_CGROUPS is not set +CONFIG_FAIR_GROUP_SCHED=y +CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -87,13 +97,11 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y -CONFIG_SLUB_DEBUG=y -# CONFIG_SLAB is not set -CONFIG_SLUB=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set # CONFIG_SLOB is not set CONFIG_RT_MUTEXES=y # CONFIG_TINY_SHMEM is not set @@ -108,6 +116,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set CONFIG_BLK_DEV_BSG=y +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -126,7 +135,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -176,10 +184,15 @@ CONFIG_SPU_BASE=y # CONFIG_GENERIC_IOMAP is not set # CONFIG_CPU_FREQ is not set # CONFIG_CPM2 is not set +# CONFIG_FSL_ULI1575 is not set # # Kernel options # +# CONFIG_TICK_ONESHOT is not set +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -211,6 +224,8 @@ CONFIG_SPARSEMEM=y CONFIG_HAVE_MEMORY_PRESENT=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPARSEMEM_EXTREME=y +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y +CONFIG_SPARSEMEM_VMEMMAP=y CONFIG_MEMORY_HOTPLUG=y CONFIG_MEMORY_HOTPLUG_SPARSE=y CONFIG_SPLIT_PTLOCK_CPUS=4 @@ -237,10 +252,6 @@ CONFIG_GENERIC_ISA_DMA=y # CONFIG_PCI_DOMAINS is not set # CONFIG_PCI_SYSCALL is not set # CONFIG_ARCH_SUPPORTS_MSI is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set CONFIG_KERNEL_START=0xc000000000000000 @@ -280,6 +291,7 @@ CONFIG_INET_TUNNEL=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set # CONFIG_INET_DIAG is not set # CONFIG_TCP_CONG_ADVANCED is not set CONFIG_TCP_CONG_CUBIC=y @@ -318,10 +330,6 @@ CONFIG_IPV6_SIT=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -330,26 +338,7 @@ CONFIG_IPV6_SIT=y # CONFIG_NET_PKTGEN is not set # CONFIG_HAMRADIO is not set # CONFIG_IRDA is not set -CONFIG_BT=m -CONFIG_BT_L2CAP=m -CONFIG_BT_SCO=m -CONFIG_BT_RFCOMM=m -CONFIG_BT_RFCOMM_TTY=y -# CONFIG_BT_BNEP is not set -CONFIG_BT_HIDP=m - -# -# Bluetooth device drivers -# -CONFIG_BT_HCIUSB=m -CONFIG_BT_HCIUSB_SCO=y -CONFIG_BT_HCIUART=m -CONFIG_BT_HCIUART_H4=y -CONFIG_BT_HCIUART_BCSP=y -# CONFIG_BT_HCIBCM203X is not set -# CONFIG_BT_HCIBPA10X is not set -# CONFIG_BT_HCIBFUSB is not set -# CONFIG_BT_HCIVHCI is not set +# CONFIG_BT is not set # CONFIG_AF_RXRPC is not set # @@ -358,7 +347,13 @@ CONFIG_BT_HCIUART_BCSP=y # CONFIG_CFG80211 is not set CONFIG_WIRELESS_EXT=y # CONFIG_MAC80211 is not set -# CONFIG_IEEE80211 is not set +CONFIG_IEEE80211=m +# CONFIG_IEEE80211_DEBUG is not set +CONFIG_IEEE80211_CRYPT_WEP=m +CONFIG_IEEE80211_CRYPT_CCMP=m +CONFIG_IEEE80211_CRYPT_TKIP=m +CONFIG_IEEE80211_SOFTMAC=m +# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set # CONFIG_RFKILL is not set # CONFIG_NET_9P is not set @@ -369,9 +364,10 @@ CONFIG_WIRELESS_EXT=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y -# CONFIG_FW_LOADER is not set +CONFIG_FW_LOADER=m # CONFIG_DEBUG_DRIVER is not set # CONFIG_DEBUG_DEVRES is not set # CONFIG_SYS_HYPERVISOR is not set @@ -434,6 +430,7 @@ CONFIG_SCSI_WAIT_SCAN=m # CONFIG_SCSI_ISCSI_ATTRS is not set # CONFIG_SCSI_SAS_ATTRS is not set # CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set # CONFIG_SCSI_LOWLEVEL is not set # CONFIG_ATA is not set # CONFIG_MD is not set @@ -445,8 +442,15 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set -# CONFIG_NET_ETHERNET is not set +# CONFIG_VETH is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y CONFIG_MII=m +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_B44 is not set CONFIG_NETDEV_1000=y CONFIG_GELIC_NET=y # CONFIG_NETDEV_10000 is not set @@ -455,7 +459,12 @@ CONFIG_GELIC_NET=y # Wireless LAN # # CONFIG_WLAN_PRE80211 is not set -# CONFIG_WLAN_80211 is not set +CONFIG_WLAN_80211=y +# CONFIG_LIBERTAS is not set +# CONFIG_USB_ZD1201 is not set +# CONFIG_HOSTAP is not set +CONFIG_ZD1211RW=m +# CONFIG_ZD1211RW_DEBUG is not set # # USB Network Adapters @@ -464,8 +473,8 @@ CONFIG_GELIC_NET=y # CONFIG_USB_KAWETH is not set CONFIG_USB_PEGASUS=m # CONFIG_USB_RTL8150 is not set -CONFIG_USB_USBNET_MII=m CONFIG_USB_USBNET=m +CONFIG_USB_NET_AX8817X=m # CONFIG_USB_NET_CDCETHER is not set # CONFIG_USB_NET_DM9601 is not set # CONFIG_USB_NET_GL620A is not set @@ -499,9 +508,8 @@ CONFIG_INPUT_MOUSEDEV=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 -# CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set -# CONFIG_INPUT_EVDEV is not set +CONFIG_INPUT_JOYDEV=m +CONFIG_INPUT_EVDEV=m # CONFIG_INPUT_EVBUG is not set # @@ -561,7 +569,6 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=16 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set @@ -579,6 +586,13 @@ CONFIG_GEN_RTC=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -595,12 +609,6 @@ CONFIG_GEN_RTC=y # # Graphics support # -# CONFIG_BACKLIGHT_LCD_SUPPORT is not set - -# -# Display device support -# -# CONFIG_DISPLAY_SUPPORT is not set # CONFIG_VGASTATE is not set CONFIG_VIDEO_OUTPUT_CONTROL=m CONFIG_FB=y @@ -609,6 +617,7 @@ CONFIG_FB=y # CONFIG_FB_CFB_FILLRECT is not set # CONFIG_FB_CFB_COPYAREA is not set # CONFIG_FB_CFB_IMAGEBLIT is not set +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set CONFIG_FB_SYS_FILLRECT=y CONFIG_FB_SYS_COPYAREA=y CONFIG_FB_SYS_IMAGEBLIT=y @@ -628,8 +637,14 @@ CONFIG_FB_DEFERRED_IO=y # CONFIG_FB_S1D13XXX is not set # CONFIG_FB_IBM_GXT4500 is not set CONFIG_FB_PS3=y -CONFIG_FB_PS3_DEFAULT_SIZE_M=18 +CONFIG_FB_PS3_DEFAULT_SIZE_M=9 # CONFIG_FB_VIRTUAL is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set # # Console display driver support @@ -713,6 +728,7 @@ CONFIG_SND_PS3_DEFAULT_START_DELAY=2000 CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -776,12 +792,14 @@ CONFIG_USB_STORAGE=m # CONFIG_USB_STORAGE_DEBUG is not set # CONFIG_USB_STORAGE_DATAFAB is not set # CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set # CONFIG_USB_STORAGE_DPCM is not set # CONFIG_USB_STORAGE_USBAT is not set # CONFIG_USB_STORAGE_SDDR09 is not set # CONFIG_USB_STORAGE_SDDR55 is not set # CONFIG_USB_STORAGE_JUMPSHOT is not set # CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set # CONFIG_USB_STORAGE_KARMA is not set # CONFIG_USB_LIBUSUAL is not set @@ -839,19 +857,6 @@ CONFIG_USB_MON=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -868,7 +873,6 @@ CONFIG_EXT3_FS_XATTR=y # CONFIG_EXT3_FS_SECURITY is not set # CONFIG_EXT4DEV_FS is not set CONFIG_JBD=y -# CONFIG_JBD_DEBUG is not set CONFIG_FS_MBCACHE=y # CONFIG_REISERFS_FS is not set # CONFIG_JFS_FS is not set @@ -881,6 +885,8 @@ CONFIG_FS_MBCACHE=y CONFIG_INOTIFY=y CONFIG_INOTIFY_USER=y CONFIG_QUOTA=y +# CONFIG_QUOTA_NETLINK_INTERFACE is not set +CONFIG_PRINT_QUOTA_WARNING=y # CONFIG_QFMT_V1 is not set CONFIG_QFMT_V2=y CONFIG_QUOTACTL=y @@ -919,7 +925,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLBFS is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -938,10 +943,7 @@ CONFIG_RAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -973,10 +975,6 @@ CONFIG_CIFS=m # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -1017,10 +1015,6 @@ CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1038,17 +1032,16 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y # CONFIG_PROFILING is not set # CONFIG_KPROBES is not set +# CONFIG_MARKERS is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1060,7 +1053,7 @@ CONFIG_DETECT_SOFTLOCKUP=y CONFIG_SCHED_DEBUG=y # CONFIG_SCHEDSTATS is not set # CONFIG_TIMER_STATS is not set -# CONFIG_SLUB_DEBUG_ON is not set +# CONFIG_DEBUG_SLAB is not set # CONFIG_DEBUG_RT_MUTEXES is not set # CONFIG_RT_MUTEX_TESTER is not set CONFIG_DEBUG_SPINLOCK=y @@ -1072,9 +1065,12 @@ CONFIG_DEBUG_BUGVERBOSE=y CONFIG_DEBUG_INFO=y # CONFIG_DEBUG_VM is not set CONFIG_DEBUG_LIST=y +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set CONFIG_DEBUG_STACKOVERFLOW=y # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1088,6 +1084,7 @@ CONFIG_IRQSTACKS=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1107,22 +1104,26 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set # CONFIG_CRYPTO_BLOWFISH is not set # CONFIG_CRYPTO_TWOFISH is not set # CONFIG_CRYPTO_SERPENT is not set -# CONFIG_CRYPTO_AES is not set +CONFIG_CRYPTO_AES=m # CONFIG_CRYPTO_CAST5 is not set # CONFIG_CRYPTO_CAST6 is not set # CONFIG_CRYPTO_TEA is not set -# CONFIG_CRYPTO_ARC4 is not set +CONFIG_CRYPTO_ARC4=m # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set -# CONFIG_CRYPTO_MICHAEL_MIC is not set +CONFIG_CRYPTO_MICHAEL_MIC=m # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/pseries_defconfig b/arch/powerpc/configs/pseries_defconfig index 62a38406b62f..92bbf51ad4f0 100644 --- a/arch/powerpc/configs/pseries_defconfig +++ b/arch/powerpc/configs/pseries_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc4 -# Thu Aug 30 16:50:02 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:15 2007 # CONFIG_PPC64=y @@ -11,6 +11,7 @@ CONFIG_PPC64=y # CONFIG_POWER4_ONLY is not set CONFIG_POWER3=y CONFIG_POWER4=y +# CONFIG_TUNE_CELL is not set CONFIG_PPC_FPU=y CONFIG_ALTIVEC=y CONFIG_PPC_STD_MMU=y @@ -19,8 +20,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y CONFIG_SMP=y CONFIG_NR_CPUS=128 CONFIG_64BIT=y +CONFIG_WORD_SIZE=64 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -66,14 +72,23 @@ CONFIG_TASK_DELAY_ACCT=y CONFIG_TASK_XACCT=y CONFIG_TASK_IO_ACCOUNTING=y # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set CONFIG_AUDIT=y CONFIG_AUDITSYSCALL=y +CONFIG_AUDIT_TREE=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=17 CONFIG_CGROUPS=y +# CONFIG_CGROUP_DEBUG is not set +CONFIG_CGROUP_NS=y CONFIG_CPUSETS=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_FAIR_USER_SCHED is not set +CONFIG_FAIR_CGROUP_SCHED=y +CONFIG_CGROUP_CPUACCT=y CONFIG_SYSFS_DEPRECATED=y +CONFIG_PROC_PID_CPUSET=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" @@ -93,7 +108,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -114,6 +128,7 @@ CONFIG_STOP_MACHINE=y CONFIG_BLOCK=y # CONFIG_BLK_DEV_IO_TRACE is not set CONFIG_BLK_DEV_BSG=y +CONFIG_BLOCK_COMPAT=y # # IO Schedulers @@ -132,7 +147,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory" # Platform support # CONFIG_PPC_MULTIPLATFORM=y -# CONFIG_EMBEDDED6xx is not set # CONFIG_PPC_82xx is not set # CONFIG_PPC_83xx is not set # CONFIG_PPC_86xx is not set @@ -194,6 +208,7 @@ CONFIG_PREEMPT_NONE=y CONFIG_BINFMT_ELF=y CONFIG_BINFMT_MISC=m CONFIG_FORCE_MAX_ZONEORDER=13 +CONFIG_HUGETLB_PAGE_SIZE_VARIABLE=y CONFIG_IOMMU_VMERGE=y CONFIG_HOTPLUG_CPU=y CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y @@ -215,6 +230,8 @@ CONFIG_NEED_MULTIPLE_NODES=y CONFIG_HAVE_MEMORY_PRESENT=y # CONFIG_SPARSEMEM_STATIC is not set CONFIG_SPARSEMEM_EXTREME=y +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y +CONFIG_SPARSEMEM_VMEMMAP=y # CONFIG_MEMORY_HOTPLUG is not set CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_MIGRATION=y @@ -245,11 +262,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_PCI_MSI=y +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set CONFIG_HOTPLUG_PCI=m # CONFIG_HOTPLUG_PCI_FAKE is not set @@ -294,6 +308,7 @@ CONFIG_INET_TUNNEL=y CONFIG_INET_XFRM_MODE_TRANSPORT=y CONFIG_INET_XFRM_MODE_TUNNEL=y CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_LRO=y CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -360,6 +375,7 @@ CONFIG_NETFILTER_XT_MATCH_STATE=m CONFIG_NETFILTER_XT_MATCH_STATISTIC=m CONFIG_NETFILTER_XT_MATCH_STRING=m CONFIG_NETFILTER_XT_MATCH_TCPMSS=m +CONFIG_NETFILTER_XT_MATCH_TIME=m CONFIG_NETFILTER_XT_MATCH_U32=m CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m @@ -414,10 +430,6 @@ CONFIG_LLC=y # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set CONFIG_NET_CLS_ROUTE=y @@ -448,6 +460,7 @@ CONFIG_NET_CLS_ROUTE=y # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -508,6 +521,11 @@ CONFIG_IDE_PROC_FS=y # IDE chipset support/bugfixes # CONFIG_IDE_GENERIC=y +# CONFIG_BLK_DEV_PLATFORM is not set + +# +# PCI IDE chipsets support +# CONFIG_BLK_DEV_IDEPCI=y CONFIG_IDEPCI_SHARE_IRQ=y CONFIG_IDEPCI_PCIBUS_ORDER=y @@ -515,8 +533,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y CONFIG_BLK_DEV_GENERIC=y # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_ONLYDISK is not set # CONFIG_BLK_DEV_AEC62XX is not set # CONFIG_BLK_DEV_ALI15X3 is not set CONFIG_BLK_DEV_AMD74XX=y @@ -544,7 +560,7 @@ CONFIG_BLK_DEV_AMD74XX=y # CONFIG_BLK_DEV_TC86C001 is not set # CONFIG_IDE_ARM is not set CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set +CONFIG_IDE_ARCH_OBSOLETE_INIT=y # CONFIG_BLK_DEV_HD is not set # @@ -585,6 +601,7 @@ CONFIG_SCSI_FC_ATTRS=y CONFIG_SCSI_ISCSI_ATTRS=m CONFIG_SCSI_SAS_ATTRS=m # CONFIG_SCSI_SAS_LIBSAS is not set +CONFIG_SCSI_SRP_ATTRS=y CONFIG_SCSI_LOWLEVEL=y # CONFIG_ISCSI_TCP is not set # CONFIG_BLK_DEV_3W_XXXX_RAID is not set @@ -669,6 +686,7 @@ CONFIG_ATA=y # CONFIG_PATA_OLDPIIX is not set # CONFIG_PATA_NETCELL is not set # CONFIG_PATA_NS87410 is not set +# CONFIG_PATA_NS87415 is not set # CONFIG_PATA_OPTI is not set # CONFIG_PATA_OPTIDMA is not set # CONFIG_PATA_PDC_OLD is not set @@ -699,15 +717,10 @@ CONFIG_DM_ZERO=m CONFIG_DM_MULTIPATH=m CONFIG_DM_MULTIPATH_EMC=m # CONFIG_DM_MULTIPATH_RDAC is not set +# CONFIG_DM_MULTIPATH_HP is not set # CONFIG_DM_DELAY is not set - -# -# Fusion MPT device support -# +# CONFIG_DM_UEVENT is not set # CONFIG_FUSION is not set -# CONFIG_FUSION_SPI is not set -# CONFIG_FUSION_FC is not set -# CONFIG_FUSION_SAS is not set # # IEEE 1394 (FireWire) support @@ -723,6 +736,8 @@ CONFIG_BONDING=m # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set CONFIG_TUN=m +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_PHYLIB is not set CONFIG_NET_ETHERNET=y @@ -736,6 +751,10 @@ CONFIG_VORTEX=y # CONFIG_NET_TULIP is not set # CONFIG_HP100 is not set CONFIG_IBMVETH=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set CONFIG_NET_PCI=y CONFIG_PCNET32=y # CONFIG_PCNET32_NAPI is not set @@ -743,7 +762,6 @@ CONFIG_PCNET32=y # CONFIG_ADAPTEC_STARFIRE is not set # CONFIG_B44 is not set # CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set # CONFIG_EEPRO100 is not set CONFIG_E100=y # CONFIG_FEALNX is not set @@ -764,6 +782,7 @@ CONFIG_ACENIC_OMIT_TIGON_I=y CONFIG_E1000=y # CONFIG_E1000_NAPI is not set # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -771,6 +790,7 @@ CONFIG_E1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set CONFIG_TIGON3=y # CONFIG_BNX2 is not set @@ -780,14 +800,17 @@ CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set CONFIG_EHEA=m +# CONFIG_IXGBE is not set CONFIG_IXGB=m # CONFIG_IXGB_NAPI is not set CONFIG_S2IO=m # CONFIG_S2IO_NAPI is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_PASEMI_MAC is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set CONFIG_TR=y CONFIG_IBMOL=y # CONFIG_3C359 is not set @@ -806,7 +829,6 @@ CONFIG_IBMOL=y # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -827,6 +849,7 @@ CONFIG_SLHC=m # CONFIG_NET_FC is not set # CONFIG_SHAPER is not set CONFIG_NETCONSOLE=y +# CONFIG_NETCONSOLE_DYNAMIC is not set CONFIG_NETPOLL=y CONFIG_NETPOLL_TRAP=y CONFIG_NET_POLL_CONTROLLER=y @@ -848,7 +871,6 @@ CONFIG_INPUT_MOUSEDEV=y CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 # CONFIG_INPUT_JOYDEV is not set -# CONFIG_INPUT_TSDEV is not set # CONFIG_INPUT_EVDEV is not set # CONFIG_INPUT_EVBUG is not set @@ -935,14 +957,11 @@ CONFIG_HVC_CONSOLE=y CONFIG_HVC_RTAS=y CONFIG_HVCS=m # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set CONFIG_GEN_RTC=y # CONFIG_GEN_RTC_X is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set CONFIG_RAW_DRIVER=y CONFIG_MAX_RAW_DEVS=1024 # CONFIG_HANGCHECK_TIMER is not set @@ -1012,6 +1031,13 @@ CONFIG_I2C_ALGOBIT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -1028,18 +1054,8 @@ CONFIG_I2C_ALGOBIT=y # # Graphics support # -CONFIG_BACKLIGHT_LCD_SUPPORT=y -CONFIG_LCD_CLASS_DEVICE=m -CONFIG_BACKLIGHT_CLASS_DEVICE=y - -# -# Display device support -# -CONFIG_DISPLAY_SUPPORT=y - -# -# Display hardware drivers -# +# CONFIG_AGP is not set +# CONFIG_DRM is not set # CONFIG_VGASTATE is not set # CONFIG_VIDEO_OUTPUT_CONTROL is not set CONFIG_FB=y @@ -1048,6 +1064,7 @@ CONFIG_FB_DDC=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set # CONFIG_FB_SYS_FILLRECT is not set # CONFIG_FB_SYS_COPYAREA is not set # CONFIG_FB_SYS_IMAGEBLIT is not set @@ -1097,6 +1114,19 @@ CONFIG_FB_RADEON_BACKLIGHT=y # CONFIG_FB_PM3 is not set CONFIG_FB_IBM_GXT4500=y # CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +CONFIG_BACKLIGHT_CLASS_DEVICE=y +# CONFIG_BACKLIGHT_CORGI is not set + +# +# Display device support +# +CONFIG_DISPLAY_SUPPORT=y + +# +# Display hardware drivers +# # # Console display driver support @@ -1121,6 +1151,7 @@ CONFIG_LOGO_LINUX_CLUT224=y CONFIG_HID_SUPPORT=y CONFIG_HID=y # CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set # # USB Input Devices @@ -1258,19 +1289,6 @@ CONFIG_INFINIBAND_SRP=m # CONFIG_INFINIBAND_ISER is not set # CONFIG_EDAC is not set # CONFIG_RTC_CLASS is not set - -# -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# # CONFIG_AUXDISPLAY is not set # @@ -1315,6 +1333,7 @@ CONFIG_XFS_POSIX_ACL=y # CONFIG_GFS2_FS is not set CONFIG_OCFS2_FS=m CONFIG_OCFS2_DEBUG_MASKLOG=y +# CONFIG_OCFS2_DEBUG_FS is not set # CONFIG_MINIX_FS is not set # CONFIG_ROMFS_FS is not set CONFIG_INOTIFY=y @@ -1355,7 +1374,6 @@ CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set CONFIG_HUGETLBFS=y CONFIG_HUGETLB_PAGE=y -CONFIG_RAMFS=y CONFIG_CONFIGFS_FS=m # @@ -1374,10 +1392,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y CONFIG_NFS_V3_ACL=y @@ -1396,6 +1411,7 @@ CONFIG_NFS_ACL_SUPPORT=y CONFIG_NFS_COMMON=y CONFIG_SUNRPC=y CONFIG_SUNRPC_GSS=y +CONFIG_SUNRPC_XPRT_RDMA=m # CONFIG_SUNRPC_BIND34 is not set CONFIG_RPCSEC_GSS_KRB5=y CONFIG_RPCSEC_GSS_SPKM3=m @@ -1416,10 +1432,6 @@ CONFIG_CIFS_POSIX=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# CONFIG_NLS=y CONFIG_NLS_DEFAULT="iso8859-1" CONFIG_NLS_CODEPAGE_437=y @@ -1460,10 +1472,6 @@ CONFIG_NLS_ISO8859_1=y # CONFIG_NLS_KOI8_R is not set # CONFIG_NLS_KOI8_U is not set # CONFIG_NLS_UTF8 is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -1487,18 +1495,17 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# +CONFIG_INSTRUMENTATION=y CONFIG_PROFILING=y CONFIG_OPROFILE=y CONFIG_KPROBES=y +CONFIG_MARKERS=y # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -1522,10 +1529,13 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_LKDTM is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set CONFIG_DEBUG_STACKOVERFLOW=y # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -1535,6 +1545,7 @@ CONFIG_XMON=y CONFIG_XMON_DEFAULT=y CONFIG_XMON_DISASSEMBLY=y CONFIG_IRQSTACKS=y +CONFIG_VIRQ_DEBUG=y # CONFIG_BOOTX_TEXT is not set # CONFIG_PPC_EARLY_DEBUG is not set @@ -1543,6 +1554,7 @@ CONFIG_IRQSTACKS=y # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -1563,6 +1575,7 @@ CONFIG_CRYPTO_ECB=m CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=m # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -1577,9 +1590,12 @@ CONFIG_CRYPTO_TEA=m CONFIG_CRYPTO_ARC4=m CONFIG_CRYPTO_KHAZAD=m CONFIG_CRYPTO_ANUBIS=m +# CONFIG_CRYPTO_SEED is not set CONFIG_CRYPTO_DEFLATE=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_CRC32C=m # CONFIG_CRYPTO_CAMELLIA is not set CONFIG_CRYPTO_TEST=m +# CONFIG_CRYPTO_AUTHENC is not set # CONFIG_CRYPTO_HW is not set +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/sequoia_defconfig b/arch/powerpc/configs/sequoia_defconfig index 45a4ca0e0d7d..bc3c086ddfc0 100644 --- a/arch/powerpc/configs/sequoia_defconfig +++ b/arch/powerpc/configs/sequoia_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23-rc6 -# Fri Sep 14 13:20:06 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:17 2007 # # CONFIG_PPC64 is not set @@ -22,8 +22,13 @@ CONFIG_PHYS_64BIT=y # CONFIG_PPC_MM_SLICES is not set CONFIG_NOT_COHERENT_CACHE=y CONFIG_PPC32=y +CONFIG_WORD_SIZE=32 CONFIG_PPC_MERGE=y CONFIG_MMU=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_CLOCKEVENTS=y CONFIG_GENERIC_HARDIRQS=y CONFIG_IRQ_PER_CPU=y CONFIG_RWSEM_XCHGADD_ALGORITHM=y @@ -64,9 +69,12 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +# CONFIG_FAIR_GROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -87,7 +95,6 @@ CONFIG_FUTEX=y CONFIG_ANON_INODES=y CONFIG_EPOLL=y CONFIG_SIGNALFD=y -CONFIG_TIMERFD=y CONFIG_EVENTFD=y CONFIG_SHMEM=y CONFIG_VM_EVENT_COUNTERS=y @@ -153,6 +160,10 @@ CONFIG_440A=y # Kernel options # # CONFIG_HIGHMEM is not set +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y # CONFIG_HZ_100 is not set CONFIG_HZ_250=y # CONFIG_HZ_300 is not set @@ -174,6 +185,7 @@ CONFIG_FLATMEM_MANUAL=y CONFIG_FLATMEM=y CONFIG_FLAT_NODE_MEM_MAP=y # CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set CONFIG_SPLIT_PTLOCK_CPUS=4 CONFIG_RESOURCES_64BIT=y CONFIG_ZONE_DMA_FLAG=1 @@ -198,11 +210,8 @@ CONFIG_PCI_SYSCALL=y # CONFIG_PCIEPORTBUS is not set CONFIG_ARCH_SUPPORTS_MSI=y # CONFIG_PCI_MSI is not set +CONFIG_PCI_LEGACY=y # CONFIG_PCI_DEBUG is not set - -# -# PCCARD (PCMCIA/CardBus) support -# # CONFIG_PCCARD is not set # CONFIG_HOTPLUG_PCI is not set @@ -217,7 +226,7 @@ CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_HIGHMEM_START=0xfe000000 CONFIG_LOWMEM_SIZE=0x30000000 CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 +CONFIG_TASK_SIZE=0xc0000000 CONFIG_CONSISTENT_START=0xff100000 CONFIG_CONSISTENT_SIZE=0x00200000 CONFIG_BOOT_LOAD=0x01000000 @@ -254,6 +263,7 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_XFRM_MODE_TRANSPORT is not set # CONFIG_INET_XFRM_MODE_TUNNEL is not set # CONFIG_INET_XFRM_MODE_BEET is not set +# CONFIG_INET_LRO is not set CONFIG_INET_DIAG=y CONFIG_INET_TCP_DIAG=y # CONFIG_TCP_CONG_ADVANCED is not set @@ -279,10 +289,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -311,6 +317,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # # Generic Driver Options # +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_STANDALONE=y CONFIG_PREVENT_FIRMWARE_BUILD=y CONFIG_FW_LOADER=y @@ -338,6 +345,7 @@ CONFIG_MTD_CHAR=y # CONFIG_INFTL is not set # CONFIG_RFD_FTL is not set # CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set # # RAM/ROM/Flash chip drivers @@ -370,6 +378,7 @@ CONFIG_MTD_CFI_UTIL=y # CONFIG_MTD_COMPLEX_MAPPINGS is not set # CONFIG_MTD_PHYSMAP is not set CONFIG_MTD_PHYSMAP_OF=y +# CONFIG_MTD_INTEL_VR_NOR is not set # CONFIG_MTD_PLATRAM is not set # @@ -429,10 +438,6 @@ CONFIG_MISC_DEVICES=y # CONFIG_SCSI_NETLINK is not set # CONFIG_ATA is not set # CONFIG_MD is not set - -# -# Fusion MPT device support -# # CONFIG_FUSION is not set # @@ -451,12 +456,18 @@ CONFIG_NETDEVICES=y # CONFIG_MACVLAN is not set # CONFIG_EQUALIZER is not set # CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_IP1000 is not set # CONFIG_ARCNET is not set # CONFIG_NET_ETHERNET is not set +CONFIG_IBM_NEW_EMAC_ZMII=y +CONFIG_IBM_NEW_EMAC_RGMII=y +CONFIG_IBM_NEW_EMAC_EMAC4=y CONFIG_NETDEV_1000=y # CONFIG_ACENIC is not set # CONFIG_DL2K is not set # CONFIG_E1000 is not set +# CONFIG_E1000E is not set # CONFIG_NS83820 is not set # CONFIG_HAMACHI is not set # CONFIG_YELLOWFIN is not set @@ -464,6 +475,7 @@ CONFIG_NETDEV_1000=y # CONFIG_SIS190 is not set # CONFIG_SKGE is not set # CONFIG_SKY2 is not set +# CONFIG_SK98LIN is not set # CONFIG_VIA_VELOCITY is not set # CONFIG_TIGON3 is not set # CONFIG_BNX2 is not set @@ -472,11 +484,14 @@ CONFIG_NETDEV_1000=y CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set # CONFIG_CHELSIO_T3 is not set +# CONFIG_IXGBE is not set # CONFIG_IXGB is not set # CONFIG_S2IO is not set # CONFIG_MYRI10GE is not set # CONFIG_NETXEN_NIC is not set +# CONFIG_NIU is not set # CONFIG_MLX4_CORE is not set +# CONFIG_TEHUTI is not set # CONFIG_TR is not set # @@ -539,14 +554,11 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set # CONFIG_R3964 is not set # CONFIG_APPLICOM is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set # CONFIG_RAW_DRIVER is not set # CONFIG_TCG_TPM is not set CONFIG_DEVPORT=y @@ -560,6 +572,13 @@ CONFIG_DEVPORT=y # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set # # Multifunction device drivers @@ -576,16 +595,17 @@ CONFIG_DAB=y # # Graphics support # +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set # CONFIG_BACKLIGHT_LCD_SUPPORT is not set # # Display device support # # CONFIG_DISPLAY_SUPPORT is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_OUTPUT_CONTROL=m -# CONFIG_FB is not set -# CONFIG_FB_IBM_GXT4500 is not set # # Sound @@ -612,19 +632,6 @@ CONFIG_USB_ARCH_HAS_EHCI=y # CONFIG_RTC_CLASS is not set # -# DMA Engine support -# -# CONFIG_DMA_ENGINE is not set - -# -# DMA Clients -# - -# -# DMA Devices -# - -# # Userspace I/O # # CONFIG_UIO is not set @@ -676,7 +683,6 @@ CONFIG_SYSFS=y CONFIG_TMPFS=y # CONFIG_TMPFS_POSIX_ACL is not set # CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y # CONFIG_CONFIGFS_FS is not set # @@ -692,10 +698,12 @@ CONFIG_RAMFS=y CONFIG_JFFS2_FS=y CONFIG_JFFS2_FS_DEBUG=0 CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set # CONFIG_JFFS2_SUMMARY is not set # CONFIG_JFFS2_FS_XATTR is not set # CONFIG_JFFS2_COMPRESSION_OPTIONS is not set CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set CONFIG_JFFS2_RTIME=y # CONFIG_JFFS2_RUBIN is not set CONFIG_CRAMFS=y @@ -704,10 +712,7 @@ CONFIG_CRAMFS=y # CONFIG_QNX4FS_FS is not set # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set - -# -# Network File Systems -# +CONFIG_NETWORK_FILESYSTEMS=y CONFIG_NFS_FS=y CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set @@ -733,15 +738,7 @@ CONFIG_SUNRPC=y # # CONFIG_PARTITION_ADVANCED is not set CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# # CONFIG_NLS is not set - -# -# Distributed Lock Manager -# # CONFIG_DLM is not set # CONFIG_UCC_SLOW is not set @@ -761,16 +758,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -794,9 +788,12 @@ CONFIG_SCHED_DEBUG=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y +# CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set @@ -814,6 +811,7 @@ CONFIG_PPC_EARLY_DEBUG=y # CONFIG_PPC_EARLY_DEBUG_PAS_REALMODE is not set # CONFIG_PPC_EARLY_DEBUG_BEAT is not set CONFIG_PPC_EARLY_DEBUG_44x=y +# CONFIG_PPC_EARLY_DEBUG_CPM is not set CONFIG_PPC_EARLY_DEBUG_44x_PHYSLOW=0xef600300 CONFIG_PPC_EARLY_DEBUG_44x_PHYSHIGH=0x1 @@ -822,6 +820,7 @@ CONFIG_PPC_EARLY_DEBUG_44x_PHYSHIGH=0x1 # # CONFIG_KEYS is not set # CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y @@ -841,6 +840,7 @@ CONFIG_CRYPTO_ECB=y CONFIG_CRYPTO_CBC=y CONFIG_CRYPTO_PCBC=y # CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_XTS is not set # CONFIG_CRYPTO_CRYPTD is not set CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_FCRYPT is not set @@ -854,9 +854,12 @@ CONFIG_CRYPTO_DES=y # CONFIG_CRYPTO_ARC4 is not set # CONFIG_CRYPTO_KHAZAD is not set # CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_SEED is not set # CONFIG_CRYPTO_DEFLATE is not set # CONFIG_CRYPTO_MICHAEL_MIC is not set # CONFIG_CRYPTO_CRC32C is not set # CONFIG_CRYPTO_CAMELLIA is not set # CONFIG_CRYPTO_TEST is not set +# CONFIG_CRYPTO_AUTHENC is not set CONFIG_CRYPTO_HW=y +# CONFIG_PPC_CLOCK is not set diff --git a/arch/powerpc/configs/walnut_defconfig b/arch/powerpc/configs/walnut_defconfig index 02896ecba490..79344639b7c9 100644 --- a/arch/powerpc/configs/walnut_defconfig +++ b/arch/powerpc/configs/walnut_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.23 -# Thu Oct 18 12:54:18 2007 +# Linux kernel version: 2.6.24-rc4 +# Thu Dec 6 16:49:33 2007 # # CONFIG_PPC64 is not set @@ -65,11 +65,14 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set CONFIG_FAIR_GROUP_SCHED=y CONFIG_FAIR_USER_SCHED=y +# CONFIG_FAIR_CGROUP_SCHED is not set CONFIG_SYSFS_DEPRECATED=y # CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y @@ -281,10 +284,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_LAPB is not set # CONFIG_ECONET is not set # CONFIG_WAN_ROUTER is not set - -# -# QoS and/or fair queueing -# # CONFIG_NET_SCHED is not set # @@ -507,7 +506,6 @@ CONFIG_UNIX98_PTYS=y CONFIG_LEGACY_PTYS=y CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_IPMI_HANDLER is not set -# CONFIG_WATCHDOG is not set # CONFIG_HW_RANDOM is not set # CONFIG_NVRAM is not set # CONFIG_GEN_RTC is not set @@ -524,6 +522,7 @@ CONFIG_LEGACY_PTY_COUNT=256 # CONFIG_W1 is not set # CONFIG_POWER_SUPPLY is not set # CONFIG_HWMON is not set +# CONFIG_WATCHDOG is not set # # Sonics Silicon Backplane @@ -694,16 +693,13 @@ CONFIG_PLIST=y CONFIG_HAS_IOMEM=y CONFIG_HAS_IOPORT=y CONFIG_HAS_DMA=y - -# -# Instrumentation Support -# -# CONFIG_PROFILING is not set +# CONFIG_INSTRUMENTATION is not set # # Kernel hacking # # CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y CONFIG_ENABLE_MUST_CHECK=y CONFIG_MAGIC_SYSRQ=y # CONFIG_UNUSED_SYMBOLS is not set @@ -727,10 +723,12 @@ CONFIG_DEBUG_BUGVERBOSE=y # CONFIG_DEBUG_INFO is not set # CONFIG_DEBUG_VM is not set # CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set CONFIG_FORCED_INLINING=y # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_RCU_TORTURE_TEST is not set # CONFIG_FAULT_INJECTION is not set +# CONFIG_SAMPLES is not set # CONFIG_DEBUG_STACKOVERFLOW is not set # CONFIG_DEBUG_STACK_USAGE is not set # CONFIG_DEBUG_PAGEALLOC is not set diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c index d67bcd84f329..ed083feaf6f9 100644 --- a/arch/powerpc/kernel/asm-offsets.c +++ b/arch/powerpc/kernel/asm-offsets.c @@ -326,8 +326,7 @@ int main(void) DEFINE(VMALLOC_START_VSID, KERNEL_VSID(VMALLOC_START)); #endif -#ifdef CONFIG_PPC64 DEFINE(PGD_TABLE_SIZE, PGD_TABLE_SIZE); -#endif + return 0; } diff --git a/arch/powerpc/kernel/head_32.S b/arch/powerpc/kernel/head_32.S index a5b13ae7fd20..0f4fac512020 100644 --- a/arch/powerpc/kernel/head_32.S +++ b/arch/powerpc/kernel/head_32.S @@ -1311,7 +1311,7 @@ empty_zero_page: .globl swapper_pg_dir swapper_pg_dir: - .space 4096 + .space PGD_TABLE_SIZE .globl intercept_table intercept_table: diff --git a/arch/powerpc/kernel/head_40x.S b/arch/powerpc/kernel/head_40x.S index cfefc2df8f2a..8552e67e3a8b 100644 --- a/arch/powerpc/kernel/head_40x.S +++ b/arch/powerpc/kernel/head_40x.S @@ -994,7 +994,7 @@ empty_zero_page: .space 4096 .globl swapper_pg_dir swapper_pg_dir: - .space 4096 + .space PGD_TABLE_SIZE /* Stack for handling critical exceptions from kernel mode */ diff --git a/arch/powerpc/kernel/head_44x.S b/arch/powerpc/kernel/head_44x.S index 409db6123924..56aba84c1f6e 100644 --- a/arch/powerpc/kernel/head_44x.S +++ b/arch/powerpc/kernel/head_44x.S @@ -722,7 +722,7 @@ empty_zero_page: */ .globl swapper_pg_dir swapper_pg_dir: - .space 8192 + .space PGD_TABLE_SIZE /* Reserved 4k for the critical exception stack & 4k for the machine * check stack per CPU for kernel mode exceptions */ diff --git a/arch/powerpc/kernel/head_fsl_booke.S b/arch/powerpc/kernel/head_fsl_booke.S index 4b9822728aea..7aecb39a5a45 100644 --- a/arch/powerpc/kernel/head_fsl_booke.S +++ b/arch/powerpc/kernel/head_fsl_booke.S @@ -1035,7 +1035,7 @@ empty_zero_page: .space 4096 .globl swapper_pg_dir swapper_pg_dir: - .space 4096 + .space PGD_TABLE_SIZE /* Reserved 4k for the critical exception stack & 4k for the machine * check stack per CPU for kernel mode exceptions */ diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c index 41e13f4cc6e3..b9d88374f14f 100644 --- a/arch/powerpc/kernel/process.c +++ b/arch/powerpc/kernel/process.c @@ -350,7 +350,7 @@ struct task_struct *__switch_to(struct task_struct *prev, local_irq_save(flags); account_system_vtime(current); - account_process_tick(current, 0); + account_process_vtime(current); calculate_steal_time(); last = _switch(old_thread, new_thread); diff --git a/arch/ppc/platforms/4xx/xparameters/xparameters.h b/arch/ppc/platforms/4xx/xparameters/xparameters.h index 01aa043ff381..650888b00fb0 100644 --- a/arch/ppc/platforms/4xx/xparameters/xparameters.h +++ b/arch/ppc/platforms/4xx/xparameters/xparameters.h @@ -15,8 +15,16 @@ #if defined(CONFIG_XILINX_ML300) #include "xparameters_ml300.h" + #define XPAR_INTC_0_AC97_CONTROLLER_REF_0_PLAYBACK_VEC_ID \ + XPAR_DCR_INTC_0_OPB_AC97_CONTROLLER_REF_0_PLAYBACK_INTERRUPT_INTR + #define XPAR_INTC_0_AC97_CONTROLLER_REF_0_RECORD_VEC_ID \ + XPAR_DCR_INTC_0_OPB_AC97_CONTROLLER_REF_0_RECORD_INTERRUPT_INTR #elif defined(CONFIG_XILINX_ML403) #include "xparameters_ml403.h" + #define XPAR_INTC_0_AC97_CONTROLLER_REF_0_PLAYBACK_VEC_ID \ + XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_0_PLAYBACK_INTERRUPT_INTR + #define XPAR_INTC_0_AC97_CONTROLLER_REF_0_RECORD_VEC_ID \ + XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_0_RECORD_INTERRUPT_INTR #else /* Add other board xparameter includes here before the #else */ #error No xparameters_*.h file included diff --git a/arch/ppc/syslib/virtex_devices.c b/arch/ppc/syslib/virtex_devices.c index f658ff3b3890..7322781be1c6 100644 --- a/arch/ppc/syslib/virtex_devices.c +++ b/arch/ppc/syslib/virtex_devices.c @@ -98,13 +98,13 @@ .flags = IORESOURCE_MEM, \ }, \ { \ - .start = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_PLAYBACK_INTERRUPT_INTR, \ - .end = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_PLAYBACK_INTERRUPT_INTR, \ + .start = XPAR_INTC_0_AC97_CONTROLLER_REF_##num##_PLAYBACK_VEC_ID, \ + .end = XPAR_INTC_0_AC97_CONTROLLER_REF_##num##_PLAYBACK_VEC_ID, \ .flags = IORESOURCE_IRQ, \ }, \ { \ - .start = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_RECORD_INTERRUPT_INTR, \ - .end = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_RECORD_INTERRUPT_INTR, \ + .start = XPAR_INTC_0_AC97_CONTROLLER_REF_##num##_RECORD_VEC_ID, \ + .end = XPAR_INTC_0_AC97_CONTROLLER_REF_##num##_RECORD_VEC_ID, \ .flags = IORESOURCE_IRQ, \ }, \ }, \ diff --git a/arch/s390/kernel/entry.S b/arch/s390/kernel/entry.S index b2b2edc40eb1..1a6dac8df6fb 100644 --- a/arch/s390/kernel/entry.S +++ b/arch/s390/kernel/entry.S @@ -1079,8 +1079,10 @@ cleanup_io_leave_insn: .Lexecve_tail: .long execve_tail .Ljump_table: .long pgm_check_table .Lschedule: .long schedule +#ifdef CONFIG_PREEMPT .Lpreempt_schedule_irq: .long preempt_schedule_irq +#endif .Ltrace: .long syscall_trace .Lschedtail: .long schedule_tail .Lsysc_table: .long sys_call_table diff --git a/arch/s390/kernel/setup.c b/arch/s390/kernel/setup.c index 50f8f1e3760e..577aa7dd660e 100644 --- a/arch/s390/kernel/setup.c +++ b/arch/s390/kernel/setup.c @@ -486,9 +486,7 @@ static void setup_addressing_mode(void) if (s390_noexec) { printk("S390 execute protection active, "); set_amode_and_uaccess(PSW_ASC_SECONDARY, PSW32_ASC_SECONDARY); - return; - } - if (switch_amode) { + } else if (switch_amode) { printk("S390 address spaces switched, "); set_amode_and_uaccess(PSW_ASC_PRIMARY, PSW32_ASC_PRIMARY); } diff --git a/arch/sh/drivers/pci/ops-r7780rp.c b/arch/sh/drivers/pci/ops-r7780rp.c index f2216081ab85..48fe4032ebea 100644 --- a/arch/sh/drivers/pci/ops-r7780rp.c +++ b/arch/sh/drivers/pci/ops-r7780rp.c @@ -40,8 +40,8 @@ int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) static struct resource sh7780_io_resource = { .name = "SH7780_IO", - .start = 0x2000, - .end = 0x2000 + SH7780_PCI_IO_SIZE - 1, + .start = SH7780_PCI_IO_BASE, + .end = SH7780_PCI_IO_BASE + SH7780_PCI_IO_SIZE - 1, .flags = IORESOURCE_IO }; diff --git a/arch/sh/drivers/pci/ops-se7780.c b/arch/sh/drivers/pci/ops-se7780.c index 212674df5e13..bbdb48c124a2 100644 --- a/arch/sh/drivers/pci/ops-se7780.c +++ b/arch/sh/drivers/pci/ops-se7780.c @@ -43,8 +43,8 @@ int __init pcibios_map_platform_irq(struct pci_dev *pdev, u8 slot, u8 pin) static struct resource se7780_io_resource = { .name = "SH7780_IO", - .start = 0x2000, - .end = 0x2000 + SH7780_PCI_IO_SIZE - 1, + .start = SH7780_PCI_IO_BASE, + .end = SH7780_PCI_IO_BASE + SH7780_PCI_IO_SIZE - 1, .flags = IORESOURCE_IO }; diff --git a/arch/sh/drivers/pci/pci-sh7780.h b/arch/sh/drivers/pci/pci-sh7780.h index 00d12d0f8c1f..1d069a859de2 100644 --- a/arch/sh/drivers/pci/pci-sh7780.h +++ b/arch/sh/drivers/pci/pci-sh7780.h @@ -30,7 +30,7 @@ #define SH7780_PCI_MEMORY_BASE 0xFD000000 /* Memory space base addr */ #define SH7780_PCI_MEM_SIZE 0x01000000 /* Size of Memory window */ -#define SH7780_PCI_IO_BASE 0xFE400000 /* IO space base address */ +#define SH7780_PCI_IO_BASE 0xFE200000 /* IO space base address */ #define SH7780_PCI_IO_SIZE 0x00400000 /* Size of IO window */ #define SH7780_PCIREG_BASE 0xFE040000 /* PCI regs base address */ diff --git a/arch/sparc/kernel/devices.c b/arch/sparc/kernel/devices.c index af90a5f9ab57..b240b8863fd0 100644 --- a/arch/sparc/kernel/devices.c +++ b/arch/sparc/kernel/devices.c @@ -62,8 +62,10 @@ static int __cpu_find_by(int (*compare)(int, int, void *), void *compare_arg, int err = check_cpu_node(dp->node, &cur_inst, compare, compare_arg, prom_node, mid); - if (!err) + if (!err) { + of_node_put(dp); return 0; + } } return -ENODEV; diff --git a/arch/sparc/kernel/pcic.c b/arch/sparc/kernel/pcic.c index f2d432edc92d..4cd5d7818dc6 100644 --- a/arch/sparc/kernel/pcic.c +++ b/arch/sparc/kernel/pcic.c @@ -329,7 +329,7 @@ int __init pcic_probe(void) pcic->pcic_res_cfg_addr.name = "pcic_cfg_addr"; if ((pcic->pcic_config_space_addr = ioremap(regs[2].phys_addr, regs[2].reg_size * 2)) == 0) { - prom_printf("PCIC: Error, cannot map" + prom_printf("PCIC: Error, cannot map " "PCI Configuration Space Address.\n"); prom_halt(); } @@ -341,7 +341,7 @@ int __init pcic_probe(void) pcic->pcic_res_cfg_data.name = "pcic_cfg_data"; if ((pcic->pcic_config_space_data = ioremap(regs[3].phys_addr, regs[3].reg_size * 2)) == 0) { - prom_printf("PCIC: Error, cannot map" + prom_printf("PCIC: Error, cannot map " "PCI Configuration Space Data.\n"); prom_halt(); } @@ -518,8 +518,8 @@ static void pcic_map_pci_device(struct linux_pcic *pcic, * board in a PCI slot. We must remap it * under 64K but it is not done yet. XXX */ - printk("PCIC: Skipping I/O space at 0x%lx," - "this will Oops if a driver attaches;" + printk("PCIC: Skipping I/O space at 0x%lx, " + "this will Oops if a driver attaches " "device '%s' at %02x:%02x)\n", address, namebuf, dev->bus->number, dev->devfn); } diff --git a/arch/sparc64/defconfig b/arch/sparc64/defconfig index 22734ac08c8a..f62d9f6c5e2a 100644 --- a/arch/sparc64/defconfig +++ b/arch/sparc64/defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.24-rc1 -# Wed Oct 31 15:36:47 2007 +# Linux kernel version: 2.6.24-rc4 +# Tue Dec 4 00:37:59 2007 # CONFIG_SPARC=y CONFIG_SPARC64=y @@ -47,6 +47,7 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_USER_NS is not set +# CONFIG_PID_NS is not set # CONFIG_AUDIT is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=18 @@ -154,6 +155,7 @@ CONFIG_PCI_DOMAINS=y CONFIG_PCI_SYSCALL=y CONFIG_ARCH_SUPPORTS_MSI=y CONFIG_PCI_MSI=y +# CONFIG_PCI_LEGACY is not set # CONFIG_PCI_DEBUG is not set CONFIG_SUN_OPENPROMFS=m CONFIG_SPARC32_COMPAT=y @@ -359,7 +361,6 @@ CONFIG_IDE_GENERIC=y CONFIG_BLK_DEV_IDEPCI=y # CONFIG_IDEPCI_SHARE_IRQ is not set CONFIG_IDEPCI_PCIBUS_ORDER=y -# CONFIG_BLK_DEV_OFFBOARD is not set # CONFIG_BLK_DEV_GENERIC is not set # CONFIG_BLK_DEV_OPTI621 is not set CONFIG_BLK_DEV_IDEDMA_PCI=y @@ -584,7 +585,6 @@ CONFIG_NIU=m # CONFIG_USB_KAWETH is not set # CONFIG_USB_PEGASUS is not set # CONFIG_USB_RTL8150 is not set -# CONFIG_USB_USBNET_MII is not set # CONFIG_USB_USBNET is not set # CONFIG_WAN is not set # CONFIG_FDDI is not set @@ -780,6 +780,7 @@ CONFIG_HWMON=y # CONFIG_SENSORS_ADT7470 is not set # CONFIG_SENSORS_ATXP1 is not set # CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_I5K_AMB is not set # CONFIG_SENSORS_F71805F is not set # CONFIG_SENSORS_F71882FG is not set # CONFIG_SENSORS_F75375S is not set diff --git a/arch/sparc64/kernel/chmc.c b/arch/sparc64/kernel/chmc.c index 777d34577045..6d4f02e8a4cf 100644 --- a/arch/sparc64/kernel/chmc.c +++ b/arch/sparc64/kernel/chmc.c @@ -1,7 +1,6 @@ -/* $Id: chmc.c,v 1.4 2002/01/08 16:00:14 davem Exp $ - * memctrlr.c: Driver for UltraSPARC-III memory controller. +/* memctrlr.c: Driver for UltraSPARC-III memory controller. * - * Copyright (C) 2001 David S. Miller (davem@redhat.com) + * Copyright (C) 2001, 2007 David S. Miller (davem@davemloft.net) */ #include <linux/module.h> @@ -16,6 +15,7 @@ #include <linux/init.h> #include <asm/spitfire.h> #include <asm/chmctrl.h> +#include <asm/cpudata.h> #include <asm/oplib.h> #include <asm/prom.h> #include <asm/io.h> @@ -242,8 +242,11 @@ int chmc_getunumber(int syndrome_code, */ static u64 read_mcreg(struct mctrl_info *mp, unsigned long offset) { - unsigned long ret; - int this_cpu = get_cpu(); + unsigned long ret, this_cpu; + + preempt_disable(); + + this_cpu = real_hard_smp_processor_id(); if (mp->portid == this_cpu) { __asm__ __volatile__("ldxa [%1] %2, %0" @@ -255,7 +258,8 @@ static u64 read_mcreg(struct mctrl_info *mp, unsigned long offset) : "r" (mp->regs + offset), "i" (ASI_PHYS_BYPASS_EC_E)); } - put_cpu(); + + preempt_enable(); return ret; } diff --git a/arch/sparc64/kernel/isa.c b/arch/sparc64/kernel/isa.c index 0f19dce1c905..b5f7b354084f 100644 --- a/arch/sparc64/kernel/isa.c +++ b/arch/sparc64/kernel/isa.c @@ -155,6 +155,7 @@ void __init isa_init(void) isa_br = kzalloc(sizeof(*isa_br), GFP_KERNEL); if (!isa_br) { printk(KERN_DEBUG "isa: cannot allocate sparc_isa_bridge"); + pci_dev_put(pdev); return; } @@ -168,6 +169,7 @@ void __init isa_init(void) printk(KERN_DEBUG "isa: device registration error for %s!\n", dp->path_component_name); kfree(isa_br); + pci_dev_put(pdev); return; } diff --git a/arch/sparc64/kernel/ldc.c b/arch/sparc64/kernel/ldc.c index 217478a94128..63969f610284 100644 --- a/arch/sparc64/kernel/ldc.c +++ b/arch/sparc64/kernel/ldc.c @@ -2338,6 +2338,7 @@ static int __init ldc_init(void) unsigned long major, minor; struct mdesc_handle *hp; const u64 *v; + int err; u64 mp; hp = mdesc_grab(); @@ -2345,29 +2346,33 @@ static int __init ldc_init(void) return -ENODEV; mp = mdesc_node_by_name(hp, MDESC_NODE_NULL, "platform"); + err = -ENODEV; if (mp == MDESC_NODE_NULL) - return -ENODEV; + goto out; v = mdesc_get_property(hp, mp, "domaining-enabled", NULL); if (!v) - return -ENODEV; + goto out; major = 1; minor = 0; if (sun4v_hvapi_register(HV_GRP_LDOM, major, &minor)) { printk(KERN_INFO PFX "Could not register LDOM hvapi.\n"); - return -ENODEV; + goto out; } printk(KERN_INFO "%s", version); if (!*v) { printk(KERN_INFO PFX "Domaining disabled.\n"); - return -ENODEV; + goto out; } ldom_domaining_enabled = 1; + err = 0; - return 0; +out: + mdesc_release(hp); + return err; } core_initcall(ldc_init); diff --git a/arch/sparc64/kernel/pci_sun4v.c b/arch/sparc64/kernel/pci_sun4v.c index 8c4875bdb4a8..e587a372f3fe 100644 --- a/arch/sparc64/kernel/pci_sun4v.c +++ b/arch/sparc64/kernel/pci_sun4v.c @@ -1022,6 +1022,10 @@ void __init sun4v_pci_init(struct device_node *dp, char *model_name) } prop = of_find_property(dp, "reg", NULL); + if (!prop) { + prom_printf("SUN4V_PCI: Could not find config registers\n"); + prom_halt(); + } regs = prop->value; devhandle = (regs->phys_addr >> 32UL) & 0x0fffffff; diff --git a/arch/sparc64/kernel/smp.c b/arch/sparc64/kernel/smp.c index 7cd8d94df0dc..894b506f9636 100644 --- a/arch/sparc64/kernel/smp.c +++ b/arch/sparc64/kernel/smp.c @@ -236,8 +236,9 @@ void smp_synchronize_tick_client(void) t[i].rt, t[i].master, t[i].diff, t[i].lat); #endif - printk(KERN_INFO "CPU %d: synchronized TICK with master CPU (last diff %ld cycles," - "maxerr %lu cycles)\n", smp_processor_id(), delta, rt); + printk(KERN_INFO "CPU %d: synchronized TICK with master CPU " + "(last diff %ld cycles, maxerr %lu cycles)\n", + smp_processor_id(), delta, rt); } static void smp_start_sync_tick_client(int cpu); diff --git a/arch/um/Kconfig.i386 b/arch/um/Kconfig.i386 index e0ac74e5d4c4..717f5d3440e3 100644 --- a/arch/um/Kconfig.i386 +++ b/arch/um/Kconfig.i386 @@ -8,6 +8,13 @@ config UML_X86 bool default y +config X86_32 + bool + default y + +config RWSEM_XCHGADD_ALGORITHM + def_bool y + config 64BIT bool default n diff --git a/arch/um/Makefile-i386 b/arch/um/Makefile-i386 index 67290117d909..561e373bd850 100644 --- a/arch/um/Makefile-i386 +++ b/arch/um/Makefile-i386 @@ -22,11 +22,6 @@ export LDFLAGS HOSTCFLAGS HOSTLDFLAGS UML_OBJCOPYFLAGS endif endif -KBUILD_CFLAGS += -DCONFIG_X86_32 -KBUILD_AFLAGS += -DCONFIG_X86_32 -CONFIG_X86_32 := y -export CONFIG_X86_32 - # First of all, tune CFLAGS for the specific CPU. This actually sets cflags-y. include $(srctree)/arch/x86/Makefile_32.cpu diff --git a/arch/um/drivers/chan_user.c b/arch/um/drivers/chan_user.c index b88e93b3a39f..025764089ac8 100644 --- a/arch/um/drivers/chan_user.c +++ b/arch/um/drivers/chan_user.c @@ -74,10 +74,16 @@ void generic_free(void *data) int generic_console_write(int fd, const char *buf, int n) { + sigset_t old, no_sigio; struct termios save, new; int err; if (isatty(fd)) { + sigemptyset(&no_sigio); + sigaddset(&no_sigio, SIGIO); + if (sigprocmask(SIG_BLOCK, &no_sigio, &old)) + goto error; + CATCH_EINTR(err = tcgetattr(fd, &save)); if (err) goto error; @@ -97,8 +103,11 @@ int generic_console_write(int fd, const char *buf, int n) * Restore raw mode, in any case; we *must* ignore any error apart * EINTR, except for debug. */ - if (isatty(fd)) + if (isatty(fd)) { CATCH_EINTR(tcsetattr(fd, TCSAFLUSH, &save)); + sigprocmask(SIG_SETMASK, &old, NULL); + } + return err; error: return -errno; diff --git a/arch/um/os-Linux/time.c b/arch/um/os-Linux/time.c index ef02d941c2ad..e49280599465 100644 --- a/arch/um/os-Linux/time.c +++ b/arch/um/os-Linux/time.c @@ -77,6 +77,7 @@ long long os_nsecs(void) #ifdef UML_CONFIG_NO_HZ static int after_sleep_interval(struct timespec *ts) { + return 0; } #else static inline long long timespec_to_us(const struct timespec *ts) diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 368864dfe6eb..80b7ba4056db 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -112,8 +112,9 @@ config GENERIC_TIME_VSYSCALL bool default X86_64 - - +config ARCH_SUPPORTS_OPROFILE + bool + default y config ZONE_DMA32 @@ -148,7 +149,8 @@ config X86_SMP config X86_HT bool - depends on SMP && !(X86_VISWS || X86_VOYAGER || MK8) + depends on SMP + depends on (X86_32 && !(X86_VISWS || X86_VOYAGER)) || (X86_64 && !MK8) default y config X86_BIOS_REBOOT diff --git a/arch/x86/kernel/acpi/wakeup_32.S b/arch/x86/kernel/acpi/wakeup_32.S index a97313b1270e..1e931aaf2ef6 100644 --- a/arch/x86/kernel/acpi/wakeup_32.S +++ b/arch/x86/kernel/acpi/wakeup_32.S @@ -35,10 +35,6 @@ wakeup_code: wakeup_code_start = . .code16 - movw $0xb800, %ax - movw %ax,%fs - movw $0x0e00 + 'L', %fs:(0x10) - cli cld diff --git a/arch/x86/kernel/cpu/intel_cacheinfo.c b/arch/x86/kernel/cpu/intel_cacheinfo.c index 9921b01fe199..606fe4d55a91 100644 --- a/arch/x86/kernel/cpu/intel_cacheinfo.c +++ b/arch/x86/kernel/cpu/intel_cacheinfo.c @@ -497,7 +497,7 @@ static void __cpuinit cache_shared_cpu_map_setup(unsigned int cpu, int index) {} static void __cpuinit cache_remove_shared_cpu_map(unsigned int cpu, int index) {} #endif -static void free_cache_attributes(unsigned int cpu) +static void __cpuinit free_cache_attributes(unsigned int cpu) { int i; diff --git a/arch/x86/kernel/crash.c b/arch/x86/kernel/crash.c index 8bb482ff091b..9a5fa0abfcc7 100644 --- a/arch/x86/kernel/crash.c +++ b/arch/x86/kernel/crash.c @@ -22,6 +22,7 @@ #include <asm/nmi.h> #include <asm/hw_irq.h> #include <asm/apic.h> +#include <asm/hpet.h> #include <linux/kdebug.h> #include <asm/smp.h> @@ -140,5 +141,8 @@ void machine_crash_shutdown(struct pt_regs *regs) #if defined(CONFIG_X86_IO_APIC) disable_IO_APIC(); #endif +#ifdef CONFIG_HPET_TIMER + hpet_disable(); +#endif crash_save_cpu(regs, safe_smp_processor_id()); } diff --git a/arch/x86/kernel/head_32.S b/arch/x86/kernel/head_32.S index 374b7ece8961..ac0637a6d71c 100644 --- a/arch/x86/kernel/head_32.S +++ b/arch/x86/kernel/head_32.S @@ -193,6 +193,12 @@ default_entry: jb 10b movl %edi,(init_pg_tables_end - __PAGE_OFFSET) + /* Do an early initialization of the fixmap area */ + movl $(swapper_pg_dir - __PAGE_OFFSET), %edx + movl $(swapper_pg_pmd - __PAGE_OFFSET), %eax + addl $0x007, %eax /* 0x007 = PRESENT+RW+USER */ + movl %eax, 4092(%edx) + xorl %ebx,%ebx /* This is the boot CPU (BSP) */ jmp 3f /* @@ -208,12 +214,6 @@ default_entry: .section .init.text,"ax",@progbits #endif - /* Do an early initialization of the fixmap area */ - movl $(swapper_pg_dir - __PAGE_OFFSET), %edx - movl $(swapper_pg_pmd - __PAGE_OFFSET), %eax - addl $0x007, %eax /* 0x007 = PRESENT+RW+USER */ - movl %eax, 4092(%edx) - #ifdef CONFIG_SMP ENTRY(startup_32_smp) cld diff --git a/arch/x86/kernel/hpet.c b/arch/x86/kernel/hpet.c index 53303f2e5475..4a86ffd67ec5 100644 --- a/arch/x86/kernel/hpet.c +++ b/arch/x86/kernel/hpet.c @@ -446,6 +446,20 @@ static __init int hpet_late_init(void) } fs_initcall(hpet_late_init); +void hpet_disable(void) +{ + if (is_hpet_capable()) { + unsigned long cfg = hpet_readl(HPET_CFG); + + if (hpet_legacy_int_enabled) { + cfg &= ~HPET_CFG_LEGACY; + hpet_legacy_int_enabled = 0; + } + cfg &= ~HPET_CFG_ENABLE; + hpet_writel(cfg, HPET_CFG); + } +} + #ifdef CONFIG_HPET_EMULATE_RTC /* HPET in LegacyReplacement Mode eats up RTC interrupt line. When, HPET diff --git a/arch/x86/kernel/nmi_32.c b/arch/x86/kernel/nmi_32.c index f5cc47c60b13..80ca72e5ac29 100644 --- a/arch/x86/kernel/nmi_32.c +++ b/arch/x86/kernel/nmi_32.c @@ -106,7 +106,8 @@ static int __init check_nmi_watchdog(void) if (!per_cpu(wd_enabled, cpu)) continue; if (nmi_count(cpu) - prev_nmi_count[cpu] <= 5) { - printk("CPU#%d: NMI appears to be stuck (%d->%d)!\n", + printk(KERN_WARNING "WARNING: CPU#%d: NMI " + "appears to be stuck (%d->%d)!\n", cpu, prev_nmi_count[cpu], nmi_count(cpu)); diff --git a/arch/x86/kernel/nmi_64.c b/arch/x86/kernel/nmi_64.c index a576fd740062..4253c4e8849c 100644 --- a/arch/x86/kernel/nmi_64.c +++ b/arch/x86/kernel/nmi_64.c @@ -109,7 +109,8 @@ int __init check_nmi_watchdog (void) if (!per_cpu(wd_enabled, cpu)) continue; if (cpu_pda(cpu)->__nmi_count - counts[cpu] <= 5) { - printk("CPU#%d: NMI appears to be stuck (%d->%d)!\n", + printk(KERN_WARNING "WARNING: CPU#%d: NMI " + "appears to be stuck (%d->%d)!\n", cpu, counts[cpu], cpu_pda(cpu)->__nmi_count); diff --git a/arch/x86/kernel/reboot_32.c b/arch/x86/kernel/reboot_32.c index 9e2269d00918..bb1a0f889c5e 100644 --- a/arch/x86/kernel/reboot_32.c +++ b/arch/x86/kernel/reboot_32.c @@ -11,6 +11,7 @@ #include <linux/reboot.h> #include <asm/uaccess.h> #include <asm/apic.h> +#include <asm/hpet.h> #include <asm/desc.h> #include "mach_reboot.h" #include <asm/reboot_fixups.h> @@ -326,6 +327,9 @@ static void native_machine_shutdown(void) #ifdef CONFIG_X86_IO_APIC disable_IO_APIC(); #endif +#ifdef CONFIG_HPET_TIMER + hpet_disable(); +#endif } void __attribute__((weak)) mach_reboot_fixups(void) diff --git a/arch/x86/kernel/reboot_64.c b/arch/x86/kernel/reboot_64.c index 71b13c5f5817..53620a92a8fd 100644 --- a/arch/x86/kernel/reboot_64.c +++ b/arch/x86/kernel/reboot_64.c @@ -17,6 +17,7 @@ #include <asm/pgtable.h> #include <asm/tlbflush.h> #include <asm/apic.h> +#include <asm/hpet.h> #include <asm/gart.h> /* @@ -113,6 +114,9 @@ void machine_shutdown(void) disable_IO_APIC(); +#ifdef CONFIG_HPET_TIMER + hpet_disable(); +#endif local_irq_restore(flags); pci_iommu_shutdown(); diff --git a/arch/x86/kernel/topology.c b/arch/x86/kernel/topology.c index 8caa0b777466..7e16d675eb85 100644 --- a/arch/x86/kernel/topology.c +++ b/arch/x86/kernel/topology.c @@ -33,7 +33,7 @@ static struct i386_cpu cpu_devices[NR_CPUS]; -int arch_register_cpu(int num) +int __cpuinit arch_register_cpu(int num) { /* * CPU0 cannot be offlined due to several @@ -53,7 +53,8 @@ int arch_register_cpu(int num) } #ifdef CONFIG_HOTPLUG_CPU -void arch_unregister_cpu(int num) { +void arch_unregister_cpu(int num) +{ return unregister_cpu(&cpu_devices[num].cpu); } EXPORT_SYMBOL(arch_register_cpu); diff --git a/crypto/fcrypt.c b/crypto/fcrypt.c index d161949fdb94..a32cb68bbc60 100644 --- a/crypto/fcrypt.c +++ b/crypto/fcrypt.c @@ -51,7 +51,7 @@ #define ROUNDS 16 struct fcrypt_ctx { - u32 sched[ROUNDS]; + __be32 sched[ROUNDS]; }; /* Rotate right two 32 bit numbers as a 56 bit number */ @@ -73,8 +73,8 @@ do { \ * /afs/transarc.com/public/afsps/afs.rel31b.export-src/rxkad/sboxes.h */ #undef Z -#define Z(x) __constant_be32_to_cpu(x << 3) -static const u32 sbox0[256] = { +#define Z(x) __constant_cpu_to_be32(x << 3) +static const __be32 sbox0[256] = { Z(0xea), Z(0x7f), Z(0xb2), Z(0x64), Z(0x9d), Z(0xb0), Z(0xd9), Z(0x11), Z(0xcd), Z(0x86), Z(0x86), Z(0x91), Z(0x0a), Z(0xb2), Z(0x93), Z(0x06), Z(0x0e), Z(0x06), Z(0xd2), Z(0x65), Z(0x73), Z(0xc5), Z(0x28), Z(0x60), @@ -110,8 +110,8 @@ static const u32 sbox0[256] = { }; #undef Z -#define Z(x) __constant_be32_to_cpu((x << 27) | (x >> 5)) -static const u32 sbox1[256] = { +#define Z(x) __constant_cpu_to_be32((x << 27) | (x >> 5)) +static const __be32 sbox1[256] = { Z(0x77), Z(0x14), Z(0xa6), Z(0xfe), Z(0xb2), Z(0x5e), Z(0x8c), Z(0x3e), Z(0x67), Z(0x6c), Z(0xa1), Z(0x0d), Z(0xc2), Z(0xa2), Z(0xc1), Z(0x85), Z(0x6c), Z(0x7b), Z(0x67), Z(0xc6), Z(0x23), Z(0xe3), Z(0xf2), Z(0x89), @@ -147,8 +147,8 @@ static const u32 sbox1[256] = { }; #undef Z -#define Z(x) __constant_be32_to_cpu(x << 11) -static const u32 sbox2[256] = { +#define Z(x) __constant_cpu_to_be32(x << 11) +static const __be32 sbox2[256] = { Z(0xf0), Z(0x37), Z(0x24), Z(0x53), Z(0x2a), Z(0x03), Z(0x83), Z(0x86), Z(0xd1), Z(0xec), Z(0x50), Z(0xf0), Z(0x42), Z(0x78), Z(0x2f), Z(0x6d), Z(0xbf), Z(0x80), Z(0x87), Z(0x27), Z(0x95), Z(0xe2), Z(0xc5), Z(0x5d), @@ -184,8 +184,8 @@ static const u32 sbox2[256] = { }; #undef Z -#define Z(x) __constant_be32_to_cpu(x << 19) -static const u32 sbox3[256] = { +#define Z(x) __constant_cpu_to_be32(x << 19) +static const __be32 sbox3[256] = { Z(0xa9), Z(0x2a), Z(0x48), Z(0x51), Z(0x84), Z(0x7e), Z(0x49), Z(0xe2), Z(0xb5), Z(0xb7), Z(0x42), Z(0x33), Z(0x7d), Z(0x5d), Z(0xa6), Z(0x12), Z(0x44), Z(0x48), Z(0x6d), Z(0x28), Z(0xaa), Z(0x20), Z(0x6d), Z(0x57), @@ -225,7 +225,7 @@ static const u32 sbox3[256] = { */ #define F_ENCRYPT(R, L, sched) \ do { \ - union lc4 { u32 l; u8 c[4]; } u; \ + union lc4 { __be32 l; u8 c[4]; } u; \ u.l = sched ^ R; \ L ^= sbox0[u.c[0]] ^ sbox1[u.c[1]] ^ sbox2[u.c[2]] ^ sbox3[u.c[3]]; \ } while(0) @@ -237,7 +237,7 @@ static void fcrypt_encrypt(struct crypto_tfm *tfm, u8 *dst, const u8 *src) { const struct fcrypt_ctx *ctx = crypto_tfm_ctx(tfm); struct { - u32 l, r; + __be32 l, r; } X; memcpy(&X, src, sizeof(X)); @@ -269,7 +269,7 @@ static void fcrypt_decrypt(struct crypto_tfm *tfm, u8 *dst, const u8 *src) { const struct fcrypt_ctx *ctx = crypto_tfm_ctx(tfm); struct { - u32 l, r; + __be32 l, r; } X; memcpy(&X, src, sizeof(X)); @@ -328,22 +328,22 @@ static int fcrypt_setkey(struct crypto_tfm *tfm, const u8 *key, unsigned int key k |= (*key) >> 1; /* Use lower 32 bits for schedule, rotate by 11 each round (16 times) */ - ctx->sched[0x0] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x1] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x2] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x3] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x4] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x5] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x6] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x7] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x8] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0x9] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0xa] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0xb] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0xc] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0xd] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0xe] = be32_to_cpu(k); ror56_64(k, 11); - ctx->sched[0xf] = be32_to_cpu(k); + ctx->sched[0x0] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x1] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x2] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x3] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x4] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x5] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x6] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x7] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x8] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0x9] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0xa] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0xb] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0xc] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0xd] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0xe] = cpu_to_be32(k); ror56_64(k, 11); + ctx->sched[0xf] = cpu_to_be32(k); return 0; #else @@ -369,22 +369,22 @@ static int fcrypt_setkey(struct crypto_tfm *tfm, const u8 *key, unsigned int key lo |= (*key) >> 1; /* Use lower 32 bits for schedule, rotate by 11 each round (16 times) */ - ctx->sched[0x0] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x1] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x2] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x3] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x4] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x5] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x6] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x7] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x8] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0x9] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0xa] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0xb] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0xc] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0xd] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0xe] = be32_to_cpu(lo); ror56(hi, lo, 11); - ctx->sched[0xf] = be32_to_cpu(lo); + ctx->sched[0x0] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x1] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x2] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x3] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x4] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x5] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x6] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x7] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x8] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0x9] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0xa] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0xb] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0xc] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0xd] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0xe] = cpu_to_be32(lo); ror56(hi, lo, 11); + ctx->sched[0xf] = cpu_to_be32(lo); return 0; #endif } diff --git a/drivers/acpi/dispatcher/dsobject.c b/drivers/acpi/dispatcher/dsobject.c index a474ca2334d5..954ac8ce958a 100644 --- a/drivers/acpi/dispatcher/dsobject.c +++ b/drivers/acpi/dispatcher/dsobject.c @@ -137,6 +137,71 @@ acpi_ds_build_internal_object(struct acpi_walk_state *walk_state, return_ACPI_STATUS(status); } } + + /* Special object resolution for elements of a package */ + + if ((op->common.parent->common.aml_opcode == AML_PACKAGE_OP) || + (op->common.parent->common.aml_opcode == + AML_VAR_PACKAGE_OP)) { + /* + * Attempt to resolve the node to a value before we insert it into + * the package. If this is a reference to a common data type, + * resolve it immediately. According to the ACPI spec, package + * elements can only be "data objects" or method references. + * Attempt to resolve to an Integer, Buffer, String or Package. + * If cannot, return the named reference (for things like Devices, + * Methods, etc.) Buffer Fields and Fields will resolve to simple + * objects (int/buf/str/pkg). + * + * NOTE: References to things like Devices, Methods, Mutexes, etc. + * will remain as named references. This behavior is not described + * in the ACPI spec, but it appears to be an oversight. + */ + obj_desc = (union acpi_operand_object *)op->common.node; + + status = + acpi_ex_resolve_node_to_value(ACPI_CAST_INDIRECT_PTR + (struct + acpi_namespace_node, + &obj_desc), + walk_state); + if (ACPI_FAILURE(status)) { + return_ACPI_STATUS(status); + } + + switch (op->common.node->type) { + /* + * For these types, we need the actual node, not the subobject. + * However, the subobject got an extra reference count above. + */ + case ACPI_TYPE_MUTEX: + case ACPI_TYPE_METHOD: + case ACPI_TYPE_POWER: + case ACPI_TYPE_PROCESSOR: + case ACPI_TYPE_EVENT: + case ACPI_TYPE_REGION: + case ACPI_TYPE_DEVICE: + case ACPI_TYPE_THERMAL: + + obj_desc = + (union acpi_operand_object *)op->common. + node; + break; + + default: + break; + } + + /* + * If above resolved to an operand object, we are done. Otherwise, + * we have a NS node, we must create the package entry as a named + * reference. + */ + if (ACPI_GET_DESCRIPTOR_TYPE(obj_desc) != + ACPI_DESC_TYPE_NAMED) { + goto exit; + } + } } /* Create and init a new internal ACPI object */ @@ -156,6 +221,7 @@ acpi_ds_build_internal_object(struct acpi_walk_state *walk_state, return_ACPI_STATUS(status); } + exit: *obj_desc_ptr = obj_desc; return_ACPI_STATUS(AE_OK); } @@ -356,12 +422,25 @@ acpi_ds_build_internal_package_obj(struct acpi_walk_state *walk_state, arg = arg->common.next; for (i = 0; arg && (i < element_count); i++) { if (arg->common.aml_opcode == AML_INT_RETURN_VALUE_OP) { - - /* This package element is already built, just get it */ - - obj_desc->package.elements[i] = - ACPI_CAST_PTR(union acpi_operand_object, - arg->common.node); + if (arg->common.node->type == ACPI_TYPE_METHOD) { + /* + * A method reference "looks" to the parser to be a method + * invocation, so we special case it here + */ + arg->common.aml_opcode = AML_INT_NAMEPATH_OP; + status = + acpi_ds_build_internal_object(walk_state, + arg, + &obj_desc-> + package. + elements[i]); + } else { + /* This package element is already built, just get it */ + + obj_desc->package.elements[i] = + ACPI_CAST_PTR(union acpi_operand_object, + arg->common.node); + } } else { status = acpi_ds_build_internal_object(walk_state, arg, &obj_desc-> diff --git a/drivers/acpi/processor_idle.c b/drivers/acpi/processor_idle.c index b1fbee3f7fe1..2fe34cc73c13 100644 --- a/drivers/acpi/processor_idle.c +++ b/drivers/acpi/processor_idle.c @@ -531,6 +531,11 @@ static void acpi_processor_idle(void) case ACPI_STATE_C3: /* + * Must be done before busmaster disable as we might + * need to access HPET ! + */ + acpi_state_timer_broadcast(pr, cx, 1); + /* * disable bus master * bm_check implies we need ARB_DIS * !bm_check implies we need cache flush @@ -557,7 +562,6 @@ static void acpi_processor_idle(void) /* Get start time (ticks) */ t1 = inl(acpi_gbl_FADT.xpm_timer_block.address); /* Invoke C3 */ - acpi_state_timer_broadcast(pr, cx, 1); /* Tell the scheduler that we are going deep-idle: */ sched_clock_idle_sleep_event(); acpi_cstate_enter(cx); @@ -1401,9 +1405,6 @@ static int acpi_idle_enter_simple(struct cpuidle_device *dev, if (acpi_idle_suspend) return(acpi_idle_enter_c1(dev, state)); - if (pr->flags.bm_check) - acpi_idle_update_bm_rld(pr, cx); - local_irq_disable(); current_thread_info()->status &= ~TS_POLLING; /* @@ -1418,13 +1419,21 @@ static int acpi_idle_enter_simple(struct cpuidle_device *dev, return 0; } + /* + * Must be done before busmaster disable as we might need to + * access HPET ! + */ + acpi_state_timer_broadcast(pr, cx, 1); + + if (pr->flags.bm_check) + acpi_idle_update_bm_rld(pr, cx); + if (cx->type == ACPI_STATE_C3) ACPI_FLUSH_CPU_CACHE(); t1 = inl(acpi_gbl_FADT.xpm_timer_block.address); /* Tell the scheduler that we are going deep-idle: */ sched_clock_idle_sleep_event(); - acpi_state_timer_broadcast(pr, cx, 1); acpi_idle_do_entry(cx); t2 = inl(acpi_gbl_FADT.xpm_timer_block.address); diff --git a/drivers/acpi/processor_throttling.c b/drivers/acpi/processor_throttling.c index c26c61fb36c3..6742d7bc4777 100644 --- a/drivers/acpi/processor_throttling.c +++ b/drivers/acpi/processor_throttling.c @@ -29,6 +29,7 @@ #include <linux/kernel.h> #include <linux/module.h> #include <linux/init.h> +#include <linux/sched.h> #include <linux/cpufreq.h> #include <linux/proc_fs.h> #include <linux/seq_file.h> @@ -413,7 +414,7 @@ static int acpi_throttling_rdmsr(struct acpi_processor *pr, } else { msr_low = 0; msr_high = 0; - rdmsr_on_cpu(cpu, MSR_IA32_THERM_CONTROL, + rdmsr_safe(MSR_IA32_THERM_CONTROL, (u32 *)&msr_low , (u32 *) &msr_high); msr = (msr_high << 32) | msr_low; *value = (acpi_integer) msr; @@ -438,7 +439,7 @@ static int acpi_throttling_wrmsr(struct acpi_processor *pr, acpi_integer value) "HARDWARE addr space,NOT supported yet\n"); } else { msr = value; - wrmsr_on_cpu(cpu, MSR_IA32_THERM_CONTROL, + wrmsr_safe(MSR_IA32_THERM_CONTROL, msr & 0xffffffff, msr >> 32); ret = 0; } @@ -572,21 +573,32 @@ static int acpi_processor_get_throttling_ptc(struct acpi_processor *pr) return -ENODEV; pr->throttling.state = 0; - local_irq_disable(); + value = 0; ret = acpi_read_throttling_status(pr, &value); if (ret >= 0) { state = acpi_get_throttling_state(pr, value); pr->throttling.state = state; } - local_irq_enable(); return 0; } static int acpi_processor_get_throttling(struct acpi_processor *pr) { - return pr->throttling.acpi_processor_get_throttling(pr); + cpumask_t saved_mask; + int ret; + + /* + * Migrate task to the cpu pointed by pr. + */ + saved_mask = current->cpus_allowed; + set_cpus_allowed(current, cpumask_of_cpu(pr->id)); + ret = pr->throttling.acpi_processor_get_throttling(pr); + /* restore the previous state */ + set_cpus_allowed(current, saved_mask); + + return ret; } static int acpi_processor_get_fadt_info(struct acpi_processor *pr) @@ -717,21 +729,29 @@ static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr, if (state < pr->throttling_platform_limit) return -EPERM; - local_irq_disable(); value = 0; ret = acpi_get_throttling_value(pr, state, &value); if (ret >= 0) { acpi_write_throttling_state(pr, value); pr->throttling.state = state; } - local_irq_enable(); return 0; } int acpi_processor_set_throttling(struct acpi_processor *pr, int state) { - return pr->throttling.acpi_processor_set_throttling(pr, state); + cpumask_t saved_mask; + int ret; + /* + * Migrate task to the cpu pointed by pr. + */ + saved_mask = current->cpus_allowed; + set_cpus_allowed(current, cpumask_of_cpu(pr->id)); + ret = pr->throttling.acpi_processor_set_throttling(pr, state); + /* restore the previous state */ + set_cpus_allowed(current, saved_mask); + return ret; } int acpi_processor_get_throttling_info(struct acpi_processor *pr) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index ed9b407e42d4..54f38c21dd95 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -193,6 +193,8 @@ enum { ATA_FLAG_ACPI_SATA | ATA_FLAG_AN | ATA_FLAG_IPM, AHCI_LFLAG_COMMON = ATA_LFLAG_SKIP_D2H_BSY, + + ICH_MAP = 0x90, /* ICH MAP register */ }; struct ahci_cmd_hdr { @@ -536,6 +538,10 @@ static const struct pci_device_id ahci_pci_tbl[] = { { PCI_VDEVICE(NVIDIA, 0x0ad9), board_ahci }, /* MCP77 */ { PCI_VDEVICE(NVIDIA, 0x0ada), board_ahci }, /* MCP77 */ { PCI_VDEVICE(NVIDIA, 0x0adb), board_ahci }, /* MCP77 */ + { PCI_VDEVICE(NVIDIA, 0x0ab4), board_ahci }, /* MCP79 */ + { PCI_VDEVICE(NVIDIA, 0x0ab5), board_ahci }, /* MCP79 */ + { PCI_VDEVICE(NVIDIA, 0x0ab6), board_ahci }, /* MCP79 */ + { PCI_VDEVICE(NVIDIA, 0x0ab7), board_ahci }, /* MCP79 */ { PCI_VDEVICE(NVIDIA, 0x0ab8), board_ahci }, /* MCP79 */ { PCI_VDEVICE(NVIDIA, 0x0ab9), board_ahci }, /* MCP79 */ { PCI_VDEVICE(NVIDIA, 0x0aba), board_ahci }, /* MCP79 */ @@ -1267,9 +1273,9 @@ static int ahci_do_softreset(struct ata_link *link, unsigned int *class, /* prepare for SRST (AHCI-1.1 10.4.1) */ rc = ahci_kick_engine(ap, 1); - if (rc) + if (rc && rc != -EOPNOTSUPP) ata_link_printk(link, KERN_WARNING, - "failed to reset engine (errno=%d)", rc); + "failed to reset engine (errno=%d)\n", rc); ata_tf_init(link->device, &tf); @@ -1634,7 +1640,7 @@ static void ahci_port_intr(struct ata_port *ap) struct ahci_host_priv *hpriv = ap->host->private_data; int resetting = !!(ap->pflags & ATA_PFLAG_RESETTING); u32 status, qc_active; - int rc, known_irq = 0; + int rc; status = readl(port_mmio + PORT_IRQ_STAT); writel(status, port_mmio + PORT_IRQ_STAT); @@ -1692,80 +1698,12 @@ static void ahci_port_intr(struct ata_port *ap) rc = ata_qc_complete_multiple(ap, qc_active, NULL); - /* If resetting, spurious or invalid completions are expected, - * return unconditionally. - */ - if (resetting) - return; - - if (rc > 0) - return; - if (rc < 0) { + /* while resetting, invalid completions are expected */ + if (unlikely(rc < 0 && !resetting)) { ehi->err_mask |= AC_ERR_HSM; ehi->action |= ATA_EH_SOFTRESET; ata_port_freeze(ap); - return; } - - /* hmmm... a spurious interrupt */ - - /* if !NCQ, ignore. No modern ATA device has broken HSM - * implementation for non-NCQ commands. - */ - if (!ap->link.sactive) - return; - - if (status & PORT_IRQ_D2H_REG_FIS) { - if (!pp->ncq_saw_d2h) - ata_port_printk(ap, KERN_INFO, - "D2H reg with I during NCQ, " - "this message won't be printed again\n"); - pp->ncq_saw_d2h = 1; - known_irq = 1; - } - - if (status & PORT_IRQ_DMAS_FIS) { - if (!pp->ncq_saw_dmas) - ata_port_printk(ap, KERN_INFO, - "DMAS FIS during NCQ, " - "this message won't be printed again\n"); - pp->ncq_saw_dmas = 1; - known_irq = 1; - } - - if (status & PORT_IRQ_SDB_FIS) { - const __le32 *f = pp->rx_fis + RX_FIS_SDB; - - if (le32_to_cpu(f[1])) { - /* SDB FIS containing spurious completions - * might be dangerous, whine and fail commands - * with HSM violation. EH will turn off NCQ - * after several such failures. - */ - ata_ehi_push_desc(ehi, - "spurious completions during NCQ " - "issue=0x%x SAct=0x%x FIS=%08x:%08x", - readl(port_mmio + PORT_CMD_ISSUE), - readl(port_mmio + PORT_SCR_ACT), - le32_to_cpu(f[0]), le32_to_cpu(f[1])); - ehi->err_mask |= AC_ERR_HSM; - ehi->action |= ATA_EH_SOFTRESET; - ata_port_freeze(ap); - } else { - if (!pp->ncq_saw_sdb) - ata_port_printk(ap, KERN_INFO, - "spurious SDB FIS %08x:%08x during NCQ, " - "this message won't be printed again\n", - le32_to_cpu(f[0]), le32_to_cpu(f[1])); - pp->ncq_saw_sdb = 1; - } - known_irq = 1; - } - - if (!known_irq) - ata_port_printk(ap, KERN_INFO, "spurious interrupt " - "(irq_stat 0x%x active_tag 0x%x sactive 0x%x)\n", - status, ap->link.active_tag, ap->link.sactive); } static void ahci_irq_clear(struct ata_port *ap) @@ -2269,6 +2207,22 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) if (rc) return rc; + if (pdev->vendor == PCI_VENDOR_ID_INTEL && + (pdev->device == 0x2652 || pdev->device == 0x2653)) { + u8 map; + + /* ICH6s share the same PCI ID for both piix and ahci + * modes. Enabling ahci mode while MAP indicates + * combined mode is a bad idea. Yield to ata_piix. + */ + pci_read_config_byte(pdev, ICH_MAP, &map); + if (map & 0x3) { + dev_printk(KERN_INFO, &pdev->dev, "controller is in " + "combined mode, can't enable AHCI mode\n"); + return -ENODEV; + } + } + hpriv = devm_kzalloc(dev, sizeof(*hpriv), GFP_KERNEL); if (!hpriv) return -ENOMEM; diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c index 483269db2c7d..bb62a588f489 100644 --- a/drivers/ata/ata_piix.c +++ b/drivers/ata/ata_piix.c @@ -967,6 +967,20 @@ static int piix_broken_suspend(void) }, }, { + .ident = "TECRA M3", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), + DMI_MATCH(DMI_PRODUCT_NAME, "Tecra M3"), + }, + }, + { + .ident = "TECRA M4", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), + DMI_MATCH(DMI_PRODUCT_NAME, "Tecra M4"), + }, + }, + { .ident = "TECRA M5", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), @@ -981,6 +995,20 @@ static int piix_broken_suspend(void) }, }, { + .ident = "TECRA A8", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), + DMI_MATCH(DMI_PRODUCT_NAME, "TECRA A8"), + }, + }, + { + .ident = "Satellite R25", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), + DMI_MATCH(DMI_PRODUCT_NAME, "Satellite R25"), + }, + }, + { .ident = "Satellite U200", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), @@ -988,6 +1016,13 @@ static int piix_broken_suspend(void) }, }, { + .ident = "Satellite U200", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), + DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE U200"), + }, + }, + { .ident = "Satellite Pro U200", .matches = { DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 33f06277b3be..e4dea8623a71 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4140,6 +4140,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { /* Devices where NCQ should be avoided */ /* NCQ is slow */ { "WDC WD740ADFD-00", NULL, ATA_HORKAGE_NONCQ }, + { "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, }, /* http://thread.gmane.org/gmane.linux.ide/14907 */ { "FUJITSU MHT2060BH", NULL, ATA_HORKAGE_NONCQ }, /* NCQ is broken */ @@ -4154,23 +4155,6 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { { "HTS541060G9SA00", "MB3OC60D", ATA_HORKAGE_NONCQ, }, { "HTS541080G9SA00", "MB4OC60D", ATA_HORKAGE_NONCQ, }, { "HTS541010G9SA00", "MBZOC60D", ATA_HORKAGE_NONCQ, }, - /* Drives which do spurious command completion */ - { "HTS541680J9SA00", "SB2IC7EP", ATA_HORKAGE_NONCQ, }, - { "HTS541612J9SA00", "SBDIC7JP", ATA_HORKAGE_NONCQ, }, - { "HDT722516DLA380", "V43OA96A", ATA_HORKAGE_NONCQ, }, - { "Hitachi HTS541616J9SA00", "SB4OC70P", ATA_HORKAGE_NONCQ, }, - { "Hitachi HTS542525K9SA00", "BBFOC31P", ATA_HORKAGE_NONCQ, }, - { "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, }, - { "WDC WD3200AAJS-00RYA0", "12.01B01", ATA_HORKAGE_NONCQ, }, - { "FUJITSU MHV2080BH", "00840028", ATA_HORKAGE_NONCQ, }, - { "ST9120822AS", "3.CLF", ATA_HORKAGE_NONCQ, }, - { "ST9160821AS", "3.CLF", ATA_HORKAGE_NONCQ, }, - { "ST9160821AS", "3.ALD", ATA_HORKAGE_NONCQ, }, - { "ST9160821AS", "3.CCD", ATA_HORKAGE_NONCQ, }, - { "ST3160812AS", "3.ADJ", ATA_HORKAGE_NONCQ, }, - { "ST980813AS", "3.ADB", ATA_HORKAGE_NONCQ, }, - { "SAMSUNG HD401LJ", "ZZ100-15", ATA_HORKAGE_NONCQ, }, - { "Maxtor 7V300F0", "VA111900", ATA_HORKAGE_NONCQ, }, /* devices which puke on READ_NATIVE_MAX */ { "HDS724040KLSA80", "KFAOA20N", ATA_HORKAGE_BROKEN_HPA, }, @@ -4185,6 +4169,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = { /* Devices which get the IVB wrong */ { "QUANTUM FIREBALLlct10 05", "A03.0900", ATA_HORKAGE_IVB, }, { "TSSTcorp CDDVDW SH-S202J", "SB00", ATA_HORKAGE_IVB, }, + { "TSSTcorp CDDVDW SH-S202J", "SB01", ATA_HORKAGE_IVB, }, + { "TSSTcorp CDDVDW SH-S202N", "SB00", ATA_HORKAGE_IVB, }, + { "TSSTcorp CDDVDW SH-S202N", "SB01", ATA_HORKAGE_IVB, }, /* End Marker */ { } @@ -6964,12 +6951,11 @@ int ata_host_start(struct ata_host *host) if (ap->ops->port_start) { rc = ap->ops->port_start(ap); if (rc) { - ata_port_printk(ap, KERN_ERR, "failed to " - "start port (errno=%d)\n", rc); + if (rc != -ENODEV) + dev_printk(KERN_ERR, host->dev, "failed to start port %d (errno=%d)\n", i, rc); goto err_out; } } - ata_eh_freeze_port(ap); } diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c index 0dac69db1fdf..e6605f038647 100644 --- a/drivers/ata/libata-eh.c +++ b/drivers/ata/libata-eh.c @@ -1850,30 +1850,54 @@ static void ata_eh_link_report(struct ata_link *link) ehc->i.serror & SERR_DEV_XCHG ? "DevExch " : ""); for (tag = 0; tag < ATA_MAX_QUEUE; tag++) { - static const char *dma_str[] = { - [DMA_BIDIRECTIONAL] = "bidi", - [DMA_TO_DEVICE] = "out", - [DMA_FROM_DEVICE] = "in", - [DMA_NONE] = "", - }; struct ata_queued_cmd *qc = __ata_qc_from_tag(ap, tag); struct ata_taskfile *cmd = &qc->tf, *res = &qc->result_tf; + const u8 *cdb = qc->cdb; + char data_buf[20] = ""; + char cdb_buf[70] = ""; if (!(qc->flags & ATA_QCFLAG_FAILED) || qc->dev->link != link || !qc->err_mask) continue; + if (qc->dma_dir != DMA_NONE) { + static const char *dma_str[] = { + [DMA_BIDIRECTIONAL] = "bidi", + [DMA_TO_DEVICE] = "out", + [DMA_FROM_DEVICE] = "in", + }; + static const char *prot_str[] = { + [ATA_PROT_PIO] = "pio", + [ATA_PROT_DMA] = "dma", + [ATA_PROT_NCQ] = "ncq", + [ATA_PROT_ATAPI] = "pio", + [ATA_PROT_ATAPI_DMA] = "dma", + }; + + snprintf(data_buf, sizeof(data_buf), " %s %u %s", + prot_str[qc->tf.protocol], qc->nbytes, + dma_str[qc->dma_dir]); + } + + if (is_atapi_taskfile(&qc->tf)) + snprintf(cdb_buf, sizeof(cdb_buf), + "cdb %02x %02x %02x %02x %02x %02x %02x %02x " + "%02x %02x %02x %02x %02x %02x %02x %02x\n ", + cdb[0], cdb[1], cdb[2], cdb[3], + cdb[4], cdb[5], cdb[6], cdb[7], + cdb[8], cdb[9], cdb[10], cdb[11], + cdb[12], cdb[13], cdb[14], cdb[15]); + ata_dev_printk(qc->dev, KERN_ERR, "cmd %02x/%02x:%02x:%02x:%02x:%02x/%02x:%02x:%02x:%02x:%02x/%02x " - "tag %d cdb 0x%x data %u %s\n " + "tag %d%s\n %s" "res %02x/%02x:%02x:%02x:%02x:%02x/%02x:%02x:%02x:%02x:%02x/%02x " "Emask 0x%x (%s)%s\n", cmd->command, cmd->feature, cmd->nsect, cmd->lbal, cmd->lbam, cmd->lbah, cmd->hob_feature, cmd->hob_nsect, cmd->hob_lbal, cmd->hob_lbam, cmd->hob_lbah, - cmd->device, qc->tag, qc->cdb[0], qc->nbytes, - dma_str[qc->dma_dir], + cmd->device, qc->tag, data_buf, cdb_buf, res->command, res->feature, res->nsect, res->lbal, res->lbam, res->lbah, res->hob_feature, res->hob_nsect, diff --git a/drivers/ata/pata_amd.c b/drivers/ata/pata_amd.c index c5779ad4abca..3cc27b514654 100644 --- a/drivers/ata/pata_amd.c +++ b/drivers/ata/pata_amd.c @@ -25,7 +25,7 @@ #include <linux/libata.h> #define DRV_NAME "pata_amd" -#define DRV_VERSION "0.3.9" +#define DRV_VERSION "0.3.10" /** * timing_setup - shared timing computation and load @@ -115,7 +115,8 @@ static void timing_setup(struct ata_port *ap, struct ata_device *adev, int offse } /* UDMA timing */ - pci_write_config_byte(pdev, offset + 0x10 + (3 - dn), t); + if (at.udma) + pci_write_config_byte(pdev, offset + 0x10 + (3 - dn), t); } /** diff --git a/drivers/ata/pata_at32.c b/drivers/ata/pata_at32.c index bb250a48e27c..67e574de31e8 100644 --- a/drivers/ata/pata_at32.c +++ b/drivers/ata/pata_at32.c @@ -28,7 +28,7 @@ #include <asm/arch/smc.h> #define DRV_NAME "pata_at32" -#define DRV_VERSION "0.0.2" +#define DRV_VERSION "0.0.3" /* * CompactFlash controller memory layout relative to the base address: @@ -64,6 +64,8 @@ * Mode 2 | 8.3 | 240 ns | 0x07 * Mode 3 | 11.1 | 180 ns | 0x0f * Mode 4 | 16.7 | 120 ns | 0x1f + * + * Alter PIO_MASK below according to table to set maximal PIO mode. */ #define PIO_MASK (0x1f) @@ -85,36 +87,40 @@ struct at32_ide_info { */ static int pata_at32_setup_timing(struct device *dev, struct at32_ide_info *info, - const struct ata_timing *timing) + const struct ata_timing *ata) { - /* These two values are found through testing */ - const int min_recover = 25; - const int ncs_hold = 15; - struct smc_config *smc = &info->smc; + struct smc_timing timing; int active; int recover; + memset(&timing, 0, sizeof(struct smc_timing)); + /* Total cycle time */ - smc->read_cycle = timing->cyc8b; + timing.read_cycle = ata->cyc8b; /* DIOR <= CFIOR timings */ - smc->nrd_setup = timing->setup; - smc->nrd_pulse = timing->act8b; + timing.nrd_setup = ata->setup; + timing.nrd_pulse = ata->act8b; + timing.nrd_recover = ata->rec8b; + + /* Convert nanosecond timing to clock cycles */ + smc_set_timing(smc, &timing); - /* Compute recover, extend total cycle if needed */ - active = smc->nrd_setup + smc->nrd_pulse; + /* Add one extra cycle setup due to signal ring */ + smc->nrd_setup = smc->nrd_setup + 1; + + active = smc->nrd_setup + smc->nrd_pulse; recover = smc->read_cycle - active; - if (recover < min_recover) { - smc->read_cycle = active + min_recover; - recover = min_recover; - } + /* Need at least two cycles recovery */ + if (recover < 2) + smc->read_cycle = active + 2; /* (CS0, CS1, DIR, OE) <= (CFCE1, CFCE2, CFRNW, NCSX) timings */ - smc->ncs_read_setup = 0; - smc->ncs_read_pulse = active + ncs_hold; + smc->ncs_read_setup = 1; + smc->ncs_read_pulse = smc->read_cycle - 2; /* Write timings same as read timings */ smc->write_cycle = smc->read_cycle; @@ -123,11 +129,13 @@ static int pata_at32_setup_timing(struct device *dev, smc->ncs_write_setup = smc->ncs_read_setup; smc->ncs_write_pulse = smc->ncs_read_pulse; - /* Do some debugging output */ - dev_dbg(dev, "SMC: C=%d S=%d P=%d R=%d NCSS=%d NCSP=%d NCSR=%d\n", + /* Do some debugging output of ATA and SMC timings */ + dev_dbg(dev, "ATA: C=%d S=%d P=%d R=%d\n", + ata->cyc8b, ata->setup, ata->act8b, ata->rec8b); + + dev_dbg(dev, "SMC: C=%d S=%d P=%d NS=%d NP=%d\n", smc->read_cycle, smc->nrd_setup, smc->nrd_pulse, - recover, smc->ncs_read_setup, smc->ncs_read_pulse, - smc->read_cycle - smc->ncs_read_pulse); + smc->ncs_read_setup, smc->ncs_read_pulse); /* Finally, configure the SMC */ return smc_set_configuration(info->cs, smc); @@ -182,7 +190,6 @@ static struct scsi_host_template at32_sht = { }; static struct ata_port_operations at32_port_ops = { - .port_disable = ata_port_disable, .set_piomode = pata_at32_set_piomode, .tf_load = ata_tf_load, .tf_read = ata_tf_read, @@ -203,7 +210,6 @@ static struct ata_port_operations at32_port_ops = { .irq_clear = pata_at32_irq_clear, .irq_on = ata_irq_on, - .irq_ack = ata_irq_ack, .port_start = ata_sff_port_start, }; @@ -223,8 +229,7 @@ static int __init pata_at32_init_one(struct device *dev, /* Setup ATA bindings */ ap->ops = &at32_port_ops; ap->pio_mask = PIO_MASK; - ap->flags = ATA_FLAG_MMIO | ATA_FLAG_SLAVE_POSS - | ATA_FLAG_PIO_POLLING; + ap->flags |= ATA_FLAG_MMIO | ATA_FLAG_SLAVE_POSS; /* * Since all 8-bit taskfile transfers has to go on the lower @@ -357,12 +362,12 @@ static int __init pata_at32_probe(struct platform_device *pdev) info->smc.tdf_mode = 0; /* TDF optimization disabled */ info->smc.tdf_cycles = 0; /* No TDF wait cycles */ - /* Setup ATA timing */ + /* Setup SMC to ATA timing */ ret = pata_at32_setup_timing(dev, info, &initial_timing); if (ret) goto err_setup_timing; - /* Setup ATA addresses */ + /* Map ATA address space */ ret = -ENOMEM; info->ide_addr = devm_ioremap(dev, info->res_ide.start, 16); info->alt_addr = devm_ioremap(dev, info->res_alt.start, 16); @@ -373,7 +378,7 @@ static int __init pata_at32_probe(struct platform_device *pdev) pata_at32_debug_bus(dev, info); #endif - /* Register ATA device */ + /* Setup and register ATA device */ ret = pata_at32_init_one(dev, info); if (ret) goto err_ata_device; diff --git a/drivers/ata/pata_bf54x.c b/drivers/ata/pata_bf54x.c index 81db405a5445..088a41f4e656 100644 --- a/drivers/ata/pata_bf54x.c +++ b/drivers/ata/pata_bf54x.c @@ -1489,6 +1489,8 @@ static int __devinit bfin_atapi_probe(struct platform_device *pdev) int board_idx = 0; struct resource *res; struct ata_host *host; + unsigned int fsclk = get_sclk(); + int udma_mode = 5; const struct ata_port_info *ppi[] = { &bfin_port_info[board_idx], NULL }; @@ -1507,6 +1509,11 @@ static int __devinit bfin_atapi_probe(struct platform_device *pdev) if (res == NULL) return -EINVAL; + while (bfin_port_info[board_idx].udma_mask>0 && udma_fsclk[udma_mode] > fsclk) { + udma_mode--; + bfin_port_info[board_idx].udma_mask >>= 1; + } + /* * Now that that's out of the way, wire up the port.. */ diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c index a4175fbdd170..453d72bf2598 100644 --- a/drivers/ata/pata_via.c +++ b/drivers/ata/pata_via.c @@ -63,7 +63,7 @@ #include <linux/dmi.h> #define DRV_NAME "pata_via" -#define DRV_VERSION "0.3.2" +#define DRV_VERSION "0.3.3" /* * The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx @@ -296,7 +296,7 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo } /* Set UDMA unless device is not UDMA capable */ - if (udma_type) { + if (udma_type && t.udma) { u8 cable80_status; /* Get 80-wire cable detection bit */ diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index a43f64d2775b..fe0105d35bae 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -164,10 +164,14 @@ enum { MV_PCI_ERR_ATTRIBUTE = 0x1d48, MV_PCI_ERR_COMMAND = 0x1d50, - PCI_IRQ_CAUSE_OFS = 0x1d58, - PCI_IRQ_MASK_OFS = 0x1d5c, + PCI_IRQ_CAUSE_OFS = 0x1d58, + PCI_IRQ_MASK_OFS = 0x1d5c, PCI_UNMASK_ALL_IRQS = 0x7fffff, /* bits 22-0 */ + PCIE_IRQ_CAUSE_OFS = 0x1900, + PCIE_IRQ_MASK_OFS = 0x1910, + PCIE_UNMASK_ALL_IRQS = 0x70a, /* assorted bits */ + HC_MAIN_IRQ_CAUSE_OFS = 0x1d60, HC_MAIN_IRQ_MASK_OFS = 0x1d64, PORT0_ERR = (1 << 0), /* shift by port # */ @@ -303,6 +307,7 @@ enum { MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */ MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */ MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */ + MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */ /* Port private flags (pp_flags) */ MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */ @@ -388,7 +393,15 @@ struct mv_port_signal { u32 pre; }; -struct mv_host_priv; +struct mv_host_priv { + u32 hp_flags; + struct mv_port_signal signal[8]; + const struct mv_hw_ops *ops; + u32 irq_cause_ofs; + u32 irq_mask_ofs; + u32 unmask_all_irqs; +}; + struct mv_hw_ops { void (*phy_errata)(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port); @@ -401,12 +414,6 @@ struct mv_hw_ops { void (*reset_bus)(struct pci_dev *pdev, void __iomem *mmio); }; -struct mv_host_priv { - u32 hp_flags; - struct mv_port_signal signal[8]; - const struct mv_hw_ops *ops; -}; - static void mv_irq_clear(struct ata_port *ap); static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val); static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val); @@ -631,11 +638,13 @@ static const struct pci_device_id mv_pci_tbl[] = { /* Adaptec 1430SA */ { PCI_VDEVICE(ADAPTEC2, 0x0243), chip_7042 }, - { PCI_VDEVICE(TTI, 0x2310), chip_7042 }, - - /* add Marvell 7042 support */ + /* Marvell 7042 support */ { PCI_VDEVICE(MARVELL, 0x7042), chip_7042 }, + /* Highpoint RocketRAID PCIe series */ + { PCI_VDEVICE(TTI, 0x2300), chip_7042 }, + { PCI_VDEVICE(TTI, 0x2310), chip_7042 }, + { } /* terminate list */ }; @@ -1648,13 +1657,14 @@ static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc) static void mv_pci_error(struct ata_host *host, void __iomem *mmio) { + struct mv_host_priv *hpriv = host->private_data; struct ata_port *ap; struct ata_queued_cmd *qc; struct ata_eh_info *ehi; unsigned int i, err_mask, printed = 0; u32 err_cause; - err_cause = readl(mmio + PCI_IRQ_CAUSE_OFS); + err_cause = readl(mmio + hpriv->irq_cause_ofs); dev_printk(KERN_ERR, host->dev, "PCI ERROR; PCI IRQ cause=0x%08x\n", err_cause); @@ -1662,7 +1672,7 @@ static void mv_pci_error(struct ata_host *host, void __iomem *mmio) DPRINTK("All regs @ PCI error\n"); mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev)); - writelfl(0, mmio + PCI_IRQ_CAUSE_OFS); + writelfl(0, mmio + hpriv->irq_cause_ofs); for (i = 0; i < host->n_ports; i++) { ap = host->ports[i]; @@ -1926,6 +1936,8 @@ static int mv5_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, #define ZERO(reg) writel(0, mmio + (reg)) static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio) { + struct ata_host *host = dev_get_drvdata(&pdev->dev); + struct mv_host_priv *hpriv = host->private_data; u32 tmp; tmp = readl(mmio + MV_PCI_MODE); @@ -1937,8 +1949,8 @@ static void mv_reset_pci_bus(struct pci_dev *pdev, void __iomem *mmio) writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT); ZERO(HC_MAIN_IRQ_MASK_OFS); ZERO(MV_PCI_SERR_MASK); - ZERO(PCI_IRQ_CAUSE_OFS); - ZERO(PCI_IRQ_MASK_OFS); + ZERO(hpriv->irq_cause_ofs); + ZERO(hpriv->irq_mask_ofs); ZERO(MV_PCI_ERR_LOW_ADDRESS); ZERO(MV_PCI_ERR_HIGH_ADDRESS); ZERO(MV_PCI_ERR_ATTRIBUTE); @@ -2170,7 +2182,7 @@ static void mv_phy_reset(struct ata_port *ap, unsigned int *class, mv_scr_read(ap, SCR_ERROR, &serror); mv_scr_read(ap, SCR_CONTROL, &scontrol); DPRINTK("S-regs after ATA_RST: SStat 0x%08x SErr 0x%08x " - "SCtrl 0x%08x\n", status, serror, scontrol); + "SCtrl 0x%08x\n", sstatus, serror, scontrol); } #endif @@ -2490,6 +2502,16 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) break; case chip_7042: + hp_flags |= MV_HP_PCIE; + if (pdev->vendor == PCI_VENDOR_ID_TTI && + (pdev->device == 0x2300 || pdev->device == 0x2310)) + { + printk(KERN_WARNING "sata_mv: Highpoint RocketRAID BIOS" + " will CORRUPT DATA on attached drives when" + " configured as \"Legacy\". BEWARE!\n"); + printk(KERN_WARNING "sata_mv: Use BIOS \"JBOD\" volumes" + " instead for safety.\n"); + } case chip_6042: hpriv->ops = &mv6xxx_ops; hp_flags |= MV_HP_GEN_IIE; @@ -2516,6 +2538,15 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) } hpriv->hp_flags = hp_flags; + if (hp_flags & MV_HP_PCIE) { + hpriv->irq_cause_ofs = PCIE_IRQ_CAUSE_OFS; + hpriv->irq_mask_ofs = PCIE_IRQ_MASK_OFS; + hpriv->unmask_all_irqs = PCIE_UNMASK_ALL_IRQS; + } else { + hpriv->irq_cause_ofs = PCI_IRQ_CAUSE_OFS; + hpriv->irq_mask_ofs = PCI_IRQ_MASK_OFS; + hpriv->unmask_all_irqs = PCI_UNMASK_ALL_IRQS; + } return 0; } @@ -2595,10 +2626,10 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) } /* Clear any currently outstanding host interrupt conditions */ - writelfl(0, mmio + PCI_IRQ_CAUSE_OFS); + writelfl(0, mmio + hpriv->irq_cause_ofs); /* and unmask interrupt generation for host regs */ - writelfl(PCI_UNMASK_ALL_IRQS, mmio + PCI_IRQ_MASK_OFS); + writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs); if (IS_GEN_I(hpriv)) writelfl(~HC_MAIN_MASKED_IRQS_5, mmio + HC_MAIN_IRQ_MASK_OFS); @@ -2609,8 +2640,8 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) "PCI int cause/mask=0x%08x/0x%08x\n", readl(mmio + HC_MAIN_IRQ_CAUSE_OFS), readl(mmio + HC_MAIN_IRQ_MASK_OFS), - readl(mmio + PCI_IRQ_CAUSE_OFS), - readl(mmio + PCI_IRQ_MASK_OFS)); + readl(mmio + hpriv->irq_cause_ofs), + readl(mmio + hpriv->irq_mask_ofs)); done: return rc; diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c index 44f9e5d9e362..ed5dc7cb50cd 100644 --- a/drivers/ata/sata_nv.c +++ b/drivers/ata/sata_nv.c @@ -791,11 +791,13 @@ static int nv_adma_check_atapi_dma(struct ata_queued_cmd *qc) static void nv_adma_tf_read(struct ata_port *ap, struct ata_taskfile *tf) { - /* Since commands where a result TF is requested are not - executed in ADMA mode, the only time this function will be called - in ADMA mode will be if a command fails. In this case we - don't care about going into register mode with ADMA commands - pending, as the commands will all shortly be aborted anyway. */ + /* Other than when internal or pass-through commands are executed, + the only time this function will be called in ADMA mode will be + if a command fails. In the failure case we don't care about going + into register mode with ADMA commands pending, as the commands will + all shortly be aborted anyway. We assume that NCQ commands are not + issued via passthrough, which is the only way that switching into + ADMA mode could abort outstanding commands. */ nv_adma_register_mode(ap); ata_tf_read(ap, tf); @@ -1359,11 +1361,9 @@ static int nv_adma_use_reg_mode(struct ata_queued_cmd *qc) struct nv_adma_port_priv *pp = qc->ap->private_data; /* ADMA engine can only be used for non-ATAPI DMA commands, - or interrupt-driven no-data commands, where a result taskfile - is not required. */ + or interrupt-driven no-data commands. */ if ((pp->flags & NV_ADMA_ATAPI_SETUP_COMPLETE) || - (qc->tf.flags & ATA_TFLAG_POLLING) || - (qc->flags & ATA_QCFLAG_RESULT_TF)) + (qc->tf.flags & ATA_TFLAG_POLLING)) return 1; if ((qc->flags & ATA_QCFLAG_DMAMAP) || @@ -1381,6 +1381,8 @@ static void nv_adma_qc_prep(struct ata_queued_cmd *qc) NV_CPB_CTL_IEN; if (nv_adma_use_reg_mode(qc)) { + BUG_ON(!(pp->flags & NV_ADMA_ATAPI_SETUP_COMPLETE) && + (qc->flags & ATA_QCFLAG_DMAMAP)); nv_adma_register_mode(qc->ap); ata_qc_prep(qc); return; @@ -1425,9 +1427,21 @@ static unsigned int nv_adma_qc_issue(struct ata_queued_cmd *qc) VPRINTK("ENTER\n"); + /* We can't handle result taskfile with NCQ commands, since + retrieving the taskfile switches us out of ADMA mode and would abort + existing commands. */ + if (unlikely(qc->tf.protocol == ATA_PROT_NCQ && + (qc->flags & ATA_QCFLAG_RESULT_TF))) { + ata_dev_printk(qc->dev, KERN_ERR, + "NCQ w/ RESULT_TF not allowed\n"); + return AC_ERR_SYSTEM; + } + if (nv_adma_use_reg_mode(qc)) { /* use ATA register mode */ VPRINTK("using ATA register mode: 0x%lx\n", qc->flags); + BUG_ON(!(pp->flags & NV_ADMA_ATAPI_SETUP_COMPLETE) && + (qc->flags & ATA_QCFLAG_DMAMAP)); nv_adma_register_mode(qc->ap); return ata_qc_issue_prot(qc); } else diff --git a/drivers/char/apm-emulation.c b/drivers/char/apm-emulation.c index c99e43b837f5..17d54315e146 100644 --- a/drivers/char/apm-emulation.c +++ b/drivers/char/apm-emulation.c @@ -295,7 +295,6 @@ static int apm_ioctl(struct inode * inode, struct file *filp, u_int cmd, u_long arg) { struct apm_user *as = filp->private_data; - unsigned long flags; int err = -EINVAL; if (!as->suser || !as->writer) @@ -331,10 +330,16 @@ apm_ioctl(struct inode * inode, struct file *filp, u_int cmd, u_long arg) * Wait for the suspend/resume to complete. If there * are pending acknowledges, we wait here for them. */ - flags = current->flags; + freezer_do_not_count(); wait_event(apm_suspend_waitqueue, as->suspend_state == SUSPEND_DONE); + + /* + * Since we are waiting until the suspend is done, the + * try_to_freeze() in freezer_count() will not trigger + */ + freezer_count(); } else { as->suspend_state = SUSPEND_WAIT; mutex_unlock(&state_lock); @@ -362,14 +367,10 @@ apm_ioctl(struct inode * inode, struct file *filp, u_int cmd, u_long arg) * Wait for the suspend/resume to complete. If there * are pending acknowledges, we wait here for them. */ - flags = current->flags; - - wait_event_interruptible(apm_suspend_waitqueue, + wait_event_freezable(apm_suspend_waitqueue, as->suspend_state == SUSPEND_DONE); } - current->flags = flags; - mutex_lock(&state_lock); err = as->suspend_result; as->suspend_state = SUSPEND_NONE; diff --git a/drivers/char/cs5535_gpio.c b/drivers/char/cs5535_gpio.c index fe6d2407baed..c2d23cae9515 100644 --- a/drivers/char/cs5535_gpio.c +++ b/drivers/char/cs5535_gpio.c @@ -104,6 +104,11 @@ static ssize_t cs5535_gpio_write(struct file *file, const char __user *data, for (j = 0; j < ARRAY_SIZE(rm); j++) { if (c == rm[j].on) { outl(m1, base + rm[j].wr_offset); + /* If enabling output, turn off AUX 1 and AUX 2 */ + if (c == 'O') { + outl(m0, base + 0x10); + outl(m0, base + 0x14); + } break; } else if (c == rm[j].off) { outl(m0, base + rm[j].wr_offset); diff --git a/drivers/crypto/Kconfig b/drivers/crypto/Kconfig index 5fd6688a444a..ddd3a259cea1 100644 --- a/drivers/crypto/Kconfig +++ b/drivers/crypto/Kconfig @@ -12,7 +12,7 @@ if CRYPTO_HW config CRYPTO_DEV_PADLOCK tristate "Support for VIA PadLock ACE" - depends on X86_32 + depends on X86_32 && !UML select CRYPTO_ALGAPI help Some VIA processors come with an integrated crypto engine diff --git a/drivers/hwmon/coretemp.c b/drivers/hwmon/coretemp.c index 5c82ec7f8bbd..3ee60d26e3a2 100644 --- a/drivers/hwmon/coretemp.c +++ b/drivers/hwmon/coretemp.c @@ -337,11 +337,10 @@ static int coretemp_cpu_callback(struct notifier_block *nfb, switch (action) { case CPU_ONLINE: - case CPU_ONLINE_FROZEN: + case CPU_DOWN_FAILED: coretemp_device_add(cpu); break; - case CPU_DEAD: - case CPU_DEAD_FROZEN: + case CPU_DOWN_PREPARE: coretemp_device_remove(cpu); break; } diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c index f59aecf5ec15..fd9c5d51870a 100644 --- a/drivers/input/touchscreen/ads7846.c +++ b/drivers/input/touchscreen/ads7846.c @@ -267,13 +267,12 @@ static int ads7846_read12_ser(struct device *dev, unsigned command) ts->irq_disabled = 0; enable_irq(spi->irq); - if (req->msg.status) - status = req->msg.status; - - /* on-wire is a must-ignore bit, a BE12 value, then padding */ - sample = be16_to_cpu(req->sample); - sample = sample >> 3; - sample &= 0x0fff; + if (status == 0) { + /* on-wire is a must-ignore bit, a BE12 value, then padding */ + sample = be16_to_cpu(req->sample); + sample = sample >> 3; + sample &= 0x0fff; + } kfree(req); return status ? status : sample; diff --git a/drivers/isdn/i4l/isdn_common.c b/drivers/isdn/i4l/isdn_common.c index c6df2925ebd0..d6952959d72a 100644 --- a/drivers/isdn/i4l/isdn_common.c +++ b/drivers/isdn/i4l/isdn_common.c @@ -1515,6 +1515,7 @@ isdn_ioctl(struct inode *inode, struct file *file, uint cmd, ulong arg) if (copy_from_user(&iocts, argp, sizeof(isdn_ioctl_struct))) return -EFAULT; + iocts.drvid[sizeof(iocts.drvid)-1] = 0; if (strlen(iocts.drvid)) { if ((p = strchr(iocts.drvid, ','))) *p = 0; @@ -1599,6 +1600,7 @@ isdn_ioctl(struct inode *inode, struct file *file, uint cmd, ulong arg) if (copy_from_user(&iocts, argp, sizeof(isdn_ioctl_struct))) return -EFAULT; + iocts.drvid[sizeof(iocts.drvid)-1] = 0; if (strlen(iocts.drvid)) { drvidx = -1; for (i = 0; i < ISDN_MAX_DRIVERS; i++) @@ -1643,7 +1645,7 @@ isdn_ioctl(struct inode *inode, struct file *file, uint cmd, ulong arg) } else { p = (char __user *) iocts.arg; for (i = 0; i < 10; i++) { - sprintf(bname, "%s%s", + snprintf(bname, sizeof(bname), "%s%s", strlen(dev->drv[drvidx]->msn2eaz[i]) ? dev->drv[drvidx]->msn2eaz[i] : "_", (i < 9) ? "," : "\0"); @@ -1673,6 +1675,7 @@ isdn_ioctl(struct inode *inode, struct file *file, uint cmd, ulong arg) char *p; if (copy_from_user(&iocts, argp, sizeof(isdn_ioctl_struct))) return -EFAULT; + iocts.drvid[sizeof(iocts.drvid)-1] = 0; if (strlen(iocts.drvid)) { if ((p = strchr(iocts.drvid, ','))) *p = 0; diff --git a/drivers/leds/led-class.c b/drivers/leds/led-class.c index 4211293ce862..ba8b04b03b9f 100644 --- a/drivers/leds/led-class.c +++ b/drivers/leds/led-class.c @@ -111,7 +111,7 @@ int led_classdev_register(struct device *parent, struct led_classdev *led_cdev) write_unlock(&leds_list_lock); #ifdef CONFIG_LEDS_TRIGGERS - rwlock_init(&led_cdev->trigger_lock); + init_rwsem(&led_cdev->trigger_lock); rc = device_create_file(led_cdev->dev, &dev_attr_trigger); if (rc) @@ -147,10 +147,10 @@ void led_classdev_unregister(struct led_classdev *led_cdev) device_remove_file(led_cdev->dev, &dev_attr_brightness); #ifdef CONFIG_LEDS_TRIGGERS device_remove_file(led_cdev->dev, &dev_attr_trigger); - write_lock(&led_cdev->trigger_lock); + down_write(&led_cdev->trigger_lock); if (led_cdev->trigger) led_trigger_set(led_cdev, NULL); - write_unlock(&led_cdev->trigger_lock); + up_write(&led_cdev->trigger_lock); #endif device_unregister(led_cdev->dev); diff --git a/drivers/leds/led-triggers.c b/drivers/leds/led-triggers.c index 575368c2b100..0bdb786210b1 100644 --- a/drivers/leds/led-triggers.c +++ b/drivers/leds/led-triggers.c @@ -19,13 +19,14 @@ #include <linux/device.h> #include <linux/sysdev.h> #include <linux/timer.h> +#include <linux/rwsem.h> #include <linux/leds.h> #include "leds.h" /* * Nests outside led_cdev->trigger_lock */ -static DEFINE_RWLOCK(triggers_list_lock); +static DECLARE_RWSEM(triggers_list_lock); static LIST_HEAD(trigger_list); ssize_t led_trigger_store(struct device *dev, struct device_attribute *attr, @@ -44,24 +45,24 @@ ssize_t led_trigger_store(struct device *dev, struct device_attribute *attr, trigger_name[len - 1] = '\0'; if (!strcmp(trigger_name, "none")) { - write_lock(&led_cdev->trigger_lock); + down_write(&led_cdev->trigger_lock); led_trigger_set(led_cdev, NULL); - write_unlock(&led_cdev->trigger_lock); + up_write(&led_cdev->trigger_lock); return count; } - read_lock(&triggers_list_lock); + down_read(&triggers_list_lock); list_for_each_entry(trig, &trigger_list, next_trig) { if (!strcmp(trigger_name, trig->name)) { - write_lock(&led_cdev->trigger_lock); + down_write(&led_cdev->trigger_lock); led_trigger_set(led_cdev, trig); - write_unlock(&led_cdev->trigger_lock); + up_write(&led_cdev->trigger_lock); - read_unlock(&triggers_list_lock); + up_read(&triggers_list_lock); return count; } } - read_unlock(&triggers_list_lock); + up_read(&triggers_list_lock); return -EINVAL; } @@ -74,8 +75,8 @@ ssize_t led_trigger_show(struct device *dev, struct device_attribute *attr, struct led_trigger *trig; int len = 0; - read_lock(&triggers_list_lock); - read_lock(&led_cdev->trigger_lock); + down_read(&triggers_list_lock); + down_read(&led_cdev->trigger_lock); if (!led_cdev->trigger) len += sprintf(buf+len, "[none] "); @@ -89,8 +90,8 @@ ssize_t led_trigger_show(struct device *dev, struct device_attribute *attr, else len += sprintf(buf+len, "%s ", trig->name); } - read_unlock(&led_cdev->trigger_lock); - read_unlock(&triggers_list_lock); + up_read(&led_cdev->trigger_lock); + up_read(&triggers_list_lock); len += sprintf(len+buf, "\n"); return len; @@ -145,14 +146,14 @@ void led_trigger_set_default(struct led_classdev *led_cdev) if (!led_cdev->default_trigger) return; - read_lock(&triggers_list_lock); - write_lock(&led_cdev->trigger_lock); + down_read(&triggers_list_lock); + down_write(&led_cdev->trigger_lock); list_for_each_entry(trig, &trigger_list, next_trig) { if (!strcmp(led_cdev->default_trigger, trig->name)) led_trigger_set(led_cdev, trig); } - write_unlock(&led_cdev->trigger_lock); - read_unlock(&triggers_list_lock); + up_write(&led_cdev->trigger_lock); + up_read(&triggers_list_lock); } int led_trigger_register(struct led_trigger *trigger) @@ -163,18 +164,18 @@ int led_trigger_register(struct led_trigger *trigger) INIT_LIST_HEAD(&trigger->led_cdevs); /* Add to the list of led triggers */ - write_lock(&triggers_list_lock); + down_write(&triggers_list_lock); list_add_tail(&trigger->next_trig, &trigger_list); - write_unlock(&triggers_list_lock); + up_write(&triggers_list_lock); /* Register with any LEDs that have this as a default trigger */ read_lock(&leds_list_lock); list_for_each_entry(led_cdev, &leds_list, node) { - write_lock(&led_cdev->trigger_lock); + down_write(&led_cdev->trigger_lock); if (!led_cdev->trigger && led_cdev->default_trigger && !strcmp(led_cdev->default_trigger, trigger->name)) led_trigger_set(led_cdev, trigger); - write_unlock(&led_cdev->trigger_lock); + up_write(&led_cdev->trigger_lock); } read_unlock(&leds_list_lock); @@ -206,17 +207,17 @@ void led_trigger_unregister(struct led_trigger *trigger) struct led_classdev *led_cdev; /* Remove from the list of led triggers */ - write_lock(&triggers_list_lock); + down_write(&triggers_list_lock); list_del(&trigger->next_trig); - write_unlock(&triggers_list_lock); + up_write(&triggers_list_lock); /* Remove anyone actively using this trigger */ read_lock(&leds_list_lock); list_for_each_entry(led_cdev, &leds_list, node) { - write_lock(&led_cdev->trigger_lock); + down_write(&led_cdev->trigger_lock); if (led_cdev->trigger == trigger) led_trigger_set(led_cdev, NULL); - write_unlock(&led_cdev->trigger_lock); + up_write(&led_cdev->trigger_lock); } read_unlock(&leds_list_lock); } diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c index a6469218f194..365024b83d3d 100644 --- a/drivers/mmc/host/mmc_spi.c +++ b/drivers/mmc/host/mmc_spi.c @@ -176,8 +176,6 @@ mmc_spi_readbytes(struct mmc_spi_host *host, unsigned len) DMA_FROM_DEVICE); status = spi_sync(host->spi, &host->readback); - if (status == 0) - status = host->readback.status; if (host->dma_dev) dma_sync_single_for_cpu(host->dma_dev, @@ -480,8 +478,6 @@ mmc_spi_command_send(struct mmc_spi_host *host, DMA_BIDIRECTIONAL); } status = spi_sync(host->spi, &host->m); - if (status == 0) - status = host->m.status; if (host->dma_dev) dma_sync_single_for_cpu(host->dma_dev, @@ -624,8 +620,6 @@ mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t) DMA_BIDIRECTIONAL); status = spi_sync(spi, &host->m); - if (status == 0) - status = host->m.status; if (status != 0) { dev_dbg(&spi->dev, "write error (%d)\n", status); @@ -726,8 +720,6 @@ mmc_spi_readblock(struct mmc_spi_host *host, struct spi_transfer *t) } status = spi_sync(spi, &host->m); - if (status == 0) - status = host->m.status; if (host->dma_dev) { dma_sync_single_for_cpu(host->dma_dev, @@ -905,8 +897,6 @@ mmc_spi_data_do(struct mmc_spi_host *host, struct mmc_command *cmd, DMA_BIDIRECTIONAL); tmp = spi_sync(spi, &host->m); - if (tmp == 0) - tmp = host->m.status; if (host->dma_dev) dma_sync_single_for_cpu(host->dma_dev, diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index e8d69b0adf90..6cde4edc846b 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -888,7 +888,7 @@ config SMC91X tristate "SMC 91C9x/91C1xxx support" select CRC32 select MII - depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BFIN + depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BLACKFIN help This is a driver for SMC's 91x series of Ethernet chipsets, including the SMC91C94 and the SMC91C111. Say Y if you want it @@ -926,7 +926,7 @@ config SMC911X tristate "SMSC LAN911[5678] support" select CRC32 select MII - depends on ARCH_PXA || SUPERH + depends on ARCH_PXA || SH_MAGIC_PANEL_R2 help This is a driver for SMSC's LAN911x series of Ethernet chipsets including the new LAN9115, LAN9116, LAN9117, and LAN9118. @@ -2588,6 +2588,7 @@ config MLX4_DEBUG config TEHUTI tristate "Tehuti Networks 10G Ethernet" depends on PCI + select ZLIB_INFLATE help Tehuti Networks 10G Ethernet NIC diff --git a/drivers/net/amd8111e.c b/drivers/net/amd8111e.c index eebf5bb2b03a..e7fdd81919bd 100644 --- a/drivers/net/amd8111e.c +++ b/drivers/net/amd8111e.c @@ -1340,7 +1340,9 @@ static int amd8111e_close(struct net_device * dev) struct amd8111e_priv *lp = netdev_priv(dev); netif_stop_queue(dev); +#ifdef CONFIG_AMD8111E_NAPI napi_disable(&lp->napi); +#endif spin_lock_irq(&lp->lock); @@ -1372,7 +1374,9 @@ static int amd8111e_open(struct net_device * dev ) dev->name, dev)) return -EAGAIN; +#ifdef CONFIG_AMD8111E_NAPI napi_enable(&lp->napi); +#endif spin_lock_irq(&lp->lock); @@ -1380,7 +1384,9 @@ static int amd8111e_open(struct net_device * dev ) if(amd8111e_restart(dev)){ spin_unlock_irq(&lp->lock); +#ifdef CONFIG_AMD8111E_NAPI napi_disable(&lp->napi); +#endif if (dev->irq) free_irq(dev->irq, dev); return -ENOMEM; diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c index 0b99b5549295..eb971755a3ff 100644 --- a/drivers/net/bfin_mac.c +++ b/drivers/net/bfin_mac.c @@ -676,7 +676,7 @@ static void bf537mac_rx(struct net_device *dev) skb->protocol = eth_type_trans(skb, dev); #if defined(BFIN_MAC_CSUM_OFFLOAD) skb->csum = current_rx_ptr->status.ip_payload_csum; - skb->ip_summed = CHECKSUM_PARTIAL; + skb->ip_summed = CHECKSUM_COMPLETE; #endif netif_rx(skb); diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 423298c84a1d..b0b26036266b 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -74,6 +74,7 @@ #include <linux/ethtool.h> #include <linux/if_vlan.h> #include <linux/if_bonding.h> +#include <linux/jiffies.h> #include <net/route.h> #include <net/net_namespace.h> #include "bonding.h" @@ -174,6 +175,7 @@ struct bond_parm_tbl bond_mode_tbl[] = { struct bond_parm_tbl xmit_hashtype_tbl[] = { { "layer2", BOND_XMIT_POLICY_LAYER2}, { "layer3+4", BOND_XMIT_POLICY_LAYER34}, +{ "layer2+3", BOND_XMIT_POLICY_LAYER23}, { NULL, -1}, }; @@ -2722,8 +2724,8 @@ void bond_loadbalance_arp_mon(struct work_struct *work) */ bond_for_each_slave(bond, slave, i) { if (slave->link != BOND_LINK_UP) { - if (((jiffies - slave->dev->trans_start) <= delta_in_ticks) && - ((jiffies - slave->dev->last_rx) <= delta_in_ticks)) { + if (time_before_eq(jiffies, slave->dev->trans_start + delta_in_ticks) && + time_before_eq(jiffies, slave->dev->last_rx + delta_in_ticks)) { slave->link = BOND_LINK_UP; slave->state = BOND_STATE_ACTIVE; @@ -2754,8 +2756,8 @@ void bond_loadbalance_arp_mon(struct work_struct *work) * when the source ip is 0, so don't take the link down * if we don't know our ip yet */ - if (((jiffies - slave->dev->trans_start) >= (2*delta_in_ticks)) || - (((jiffies - slave->dev->last_rx) >= (2*delta_in_ticks)) && + if (time_after_eq(jiffies, slave->dev->trans_start + 2*delta_in_ticks) || + (time_after_eq(jiffies, slave->dev->last_rx + 2*delta_in_ticks) && bond_has_ip(bond))) { slave->link = BOND_LINK_DOWN; @@ -2848,8 +2850,8 @@ void bond_activebackup_arp_mon(struct work_struct *work) */ bond_for_each_slave(bond, slave, i) { if (slave->link != BOND_LINK_UP) { - if ((jiffies - slave_last_rx(bond, slave)) <= - delta_in_ticks) { + if (time_before_eq(jiffies, + slave_last_rx(bond, slave) + delta_in_ticks)) { slave->link = BOND_LINK_UP; @@ -2858,7 +2860,7 @@ void bond_activebackup_arp_mon(struct work_struct *work) write_lock_bh(&bond->curr_slave_lock); if ((!bond->curr_active_slave) && - ((jiffies - slave->dev->trans_start) <= delta_in_ticks)) { + time_before_eq(jiffies, slave->dev->trans_start + delta_in_ticks)) { bond_change_active_slave(bond, slave); bond->current_arp_slave = NULL; } else if (bond->curr_active_slave != slave) { @@ -2897,7 +2899,7 @@ void bond_activebackup_arp_mon(struct work_struct *work) if ((slave != bond->curr_active_slave) && (!bond->current_arp_slave) && - (((jiffies - slave_last_rx(bond, slave)) >= 3*delta_in_ticks) && + (time_after_eq(jiffies, slave_last_rx(bond, slave) + 3*delta_in_ticks) && bond_has_ip(bond))) { /* a backup slave has gone down; three times * the delta allows the current slave to be @@ -2943,10 +2945,10 @@ void bond_activebackup_arp_mon(struct work_struct *work) * before being taken out. if a primary is being used, check * if it is up and needs to take over as the curr_active_slave */ - if ((((jiffies - slave->dev->trans_start) >= (2*delta_in_ticks)) || - (((jiffies - slave_last_rx(bond, slave)) >= (2*delta_in_ticks)) && - bond_has_ip(bond))) && - ((jiffies - slave->jiffies) >= 2*delta_in_ticks)) { + if ((time_after_eq(jiffies, slave->dev->trans_start + 2*delta_in_ticks) || + (time_after_eq(jiffies, slave_last_rx(bond, slave) + 2*delta_in_ticks) && + bond_has_ip(bond))) && + time_after_eq(jiffies, slave->jiffies + 2*delta_in_ticks)) { slave->link = BOND_LINK_DOWN; @@ -3604,6 +3606,24 @@ void bond_unregister_arp(struct bonding *bond) /*---------------------------- Hashing Policies -----------------------------*/ /* + * Hash for the output device based upon layer 2 and layer 3 data. If + * the packet is not IP mimic bond_xmit_hash_policy_l2() + */ +static int bond_xmit_hash_policy_l23(struct sk_buff *skb, + struct net_device *bond_dev, int count) +{ + struct ethhdr *data = (struct ethhdr *)skb->data; + struct iphdr *iph = ip_hdr(skb); + + if (skb->protocol == __constant_htons(ETH_P_IP)) { + return ((ntohl(iph->saddr ^ iph->daddr) & 0xffff) ^ + (data->h_dest[5] ^ bond_dev->dev_addr[5])) % count; + } + + return (data->h_dest[5] ^ bond_dev->dev_addr[5]) % count; +} + +/* * Hash for the output device based upon layer 3 and layer 4 data. If * the packet is a frag or not TCP or UDP, just use layer 3 data. If it is * altogether not IP, mimic bond_xmit_hash_policy_l2() @@ -4305,6 +4325,22 @@ out: /*------------------------- Device initialization ---------------------------*/ +static void bond_set_xmit_hash_policy(struct bonding *bond) +{ + switch (bond->params.xmit_policy) { + case BOND_XMIT_POLICY_LAYER23: + bond->xmit_hash_policy = bond_xmit_hash_policy_l23; + break; + case BOND_XMIT_POLICY_LAYER34: + bond->xmit_hash_policy = bond_xmit_hash_policy_l34; + break; + case BOND_XMIT_POLICY_LAYER2: + default: + bond->xmit_hash_policy = bond_xmit_hash_policy_l2; + break; + } +} + /* * set bond mode specific net device operations */ @@ -4321,10 +4357,7 @@ void bond_set_mode_ops(struct bonding *bond, int mode) break; case BOND_MODE_XOR: bond_dev->hard_start_xmit = bond_xmit_xor; - if (bond->params.xmit_policy == BOND_XMIT_POLICY_LAYER34) - bond->xmit_hash_policy = bond_xmit_hash_policy_l34; - else - bond->xmit_hash_policy = bond_xmit_hash_policy_l2; + bond_set_xmit_hash_policy(bond); break; case BOND_MODE_BROADCAST: bond_dev->hard_start_xmit = bond_xmit_broadcast; @@ -4332,10 +4365,7 @@ void bond_set_mode_ops(struct bonding *bond, int mode) case BOND_MODE_8023AD: bond_set_master_3ad_flags(bond); bond_dev->hard_start_xmit = bond_3ad_xmit_xor; - if (bond->params.xmit_policy == BOND_XMIT_POLICY_LAYER34) - bond->xmit_hash_policy = bond_xmit_hash_policy_l34; - else - bond->xmit_hash_policy = bond_xmit_hash_policy_l2; + bond_set_xmit_hash_policy(bond); break; case BOND_MODE_ALB: bond_set_master_alb_flags(bond); @@ -4462,6 +4492,27 @@ static void bond_deinit(struct net_device *bond_dev) #endif } +static void bond_work_cancel_all(struct bonding *bond) +{ + write_lock_bh(&bond->lock); + bond->kill_timers = 1; + write_unlock_bh(&bond->lock); + + if (bond->params.miimon && delayed_work_pending(&bond->mii_work)) + cancel_delayed_work(&bond->mii_work); + + if (bond->params.arp_interval && delayed_work_pending(&bond->arp_work)) + cancel_delayed_work(&bond->arp_work); + + if (bond->params.mode == BOND_MODE_ALB && + delayed_work_pending(&bond->alb_work)) + cancel_delayed_work(&bond->alb_work); + + if (bond->params.mode == BOND_MODE_8023AD && + delayed_work_pending(&bond->ad_work)) + cancel_delayed_work(&bond->ad_work); +} + /* Unregister and free all bond devices. * Caller must hold rtnl_lock. */ @@ -4472,6 +4523,7 @@ static void bond_free_all(void) list_for_each_entry_safe(bond, nxt, &bond_dev_list, bond_list) { struct net_device *bond_dev = bond->dev; + bond_work_cancel_all(bond); bond_mc_list_destroy(bond); /* Release the bonded slaves */ bond_release_all(bond_dev); @@ -4497,8 +4549,7 @@ int bond_parse_parm(char *mode_arg, struct bond_parm_tbl *tbl) for (i = 0; tbl[i].modename; i++) { if ((isdigit(*mode_arg) && tbl[i].mode == simple_strtol(mode_arg, NULL, 0)) || - (strncmp(mode_arg, tbl[i].modename, - strlen(tbl[i].modename)) == 0)) { + (strcmp(mode_arg, tbl[i].modename) == 0)) { return tbl[i].mode; } } @@ -4873,27 +4924,6 @@ out_rtnl: return res; } -static void bond_work_cancel_all(struct bonding *bond) -{ - write_lock_bh(&bond->lock); - bond->kill_timers = 1; - write_unlock_bh(&bond->lock); - - if (bond->params.miimon && delayed_work_pending(&bond->mii_work)) - cancel_delayed_work(&bond->mii_work); - - if (bond->params.arp_interval && delayed_work_pending(&bond->arp_work)) - cancel_delayed_work(&bond->arp_work); - - if (bond->params.mode == BOND_MODE_ALB && - delayed_work_pending(&bond->alb_work)) - cancel_delayed_work(&bond->alb_work); - - if (bond->params.mode == BOND_MODE_8023AD && - delayed_work_pending(&bond->ad_work)) - cancel_delayed_work(&bond->ad_work); -} - static int __init bonding_init(void) { int i; diff --git a/drivers/net/bonding/bond_sysfs.c b/drivers/net/bonding/bond_sysfs.c index b29330d8e309..11b76b352415 100644 --- a/drivers/net/bonding/bond_sysfs.c +++ b/drivers/net/bonding/bond_sysfs.c @@ -74,7 +74,7 @@ struct rw_semaphore bonding_rwsem; * "show" function for the bond_masters attribute. * The class parameter is ignored. */ -static ssize_t bonding_show_bonds(struct class *cls, char *buffer) +static ssize_t bonding_show_bonds(struct class *cls, char *buf) { int res = 0; struct bonding *bond; @@ -86,14 +86,13 @@ static ssize_t bonding_show_bonds(struct class *cls, char *buffer) /* not enough space for another interface name */ if ((PAGE_SIZE - res) > 10) res = PAGE_SIZE - 10; - res += sprintf(buffer + res, "++more++"); + res += sprintf(buf + res, "++more++ "); break; } - res += sprintf(buffer + res, "%s ", - bond->dev->name); + res += sprintf(buf + res, "%s ", bond->dev->name); } - res += sprintf(buffer + res, "\n"); - res++; + if (res) + buf[res-1] = '\n'; /* eat the leftover space */ up_read(&(bonding_rwsem)); return res; } @@ -235,14 +234,14 @@ static ssize_t bonding_show_slaves(struct device *d, /* not enough space for another interface name */ if ((PAGE_SIZE - res) > 10) res = PAGE_SIZE - 10; - res += sprintf(buf + res, "++more++"); + res += sprintf(buf + res, "++more++ "); break; } res += sprintf(buf + res, "%s ", slave->dev->name); } read_unlock(&bond->lock); - res += sprintf(buf + res, "\n"); - res++; + if (res) + buf[res-1] = '\n'; /* eat the leftover space */ return res; } @@ -406,7 +405,7 @@ static ssize_t bonding_show_mode(struct device *d, return sprintf(buf, "%s %d\n", bond_mode_tbl[bond->params.mode].modename, - bond->params.mode) + 1; + bond->params.mode); } static ssize_t bonding_store_mode(struct device *d, @@ -457,20 +456,11 @@ static ssize_t bonding_show_xmit_hash(struct device *d, struct device_attribute *attr, char *buf) { - int count; struct bonding *bond = to_bond(d); - if ((bond->params.mode != BOND_MODE_XOR) && - (bond->params.mode != BOND_MODE_8023AD)) { - // Not Applicable - count = sprintf(buf, "NA\n") + 1; - } else { - count = sprintf(buf, "%s %d\n", - xmit_hashtype_tbl[bond->params.xmit_policy].modename, - bond->params.xmit_policy) + 1; - } - - return count; + return sprintf(buf, "%s %d\n", + xmit_hashtype_tbl[bond->params.xmit_policy].modename, + bond->params.xmit_policy); } static ssize_t bonding_store_xmit_hash(struct device *d, @@ -488,15 +478,6 @@ static ssize_t bonding_store_xmit_hash(struct device *d, goto out; } - if ((bond->params.mode != BOND_MODE_XOR) && - (bond->params.mode != BOND_MODE_8023AD)) { - printk(KERN_ERR DRV_NAME - "%s: Transmit hash policy is irrelevant in this mode.\n", - bond->dev->name); - ret = -EPERM; - goto out; - } - new_value = bond_parse_parm((char *)buf, xmit_hashtype_tbl); if (new_value < 0) { printk(KERN_ERR DRV_NAME @@ -527,7 +508,7 @@ static ssize_t bonding_show_arp_validate(struct device *d, return sprintf(buf, "%s %d\n", arp_validate_tbl[bond->params.arp_validate].modename, - bond->params.arp_validate) + 1; + bond->params.arp_validate); } static ssize_t bonding_store_arp_validate(struct device *d, @@ -627,7 +608,7 @@ static ssize_t bonding_show_arp_interval(struct device *d, { struct bonding *bond = to_bond(d); - return sprintf(buf, "%d\n", bond->params.arp_interval) + 1; + return sprintf(buf, "%d\n", bond->params.arp_interval); } static ssize_t bonding_store_arp_interval(struct device *d, @@ -712,9 +693,7 @@ static ssize_t bonding_show_arp_targets(struct device *d, NIPQUAD(bond->params.arp_targets[i])); } if (res) - res--; /* eat the leftover space */ - res += sprintf(buf + res, "\n"); - res++; + buf[res-1] = '\n'; /* eat the leftover space */ return res; } @@ -815,7 +794,7 @@ static ssize_t bonding_show_downdelay(struct device *d, { struct bonding *bond = to_bond(d); - return sprintf(buf, "%d\n", bond->params.downdelay * bond->params.miimon) + 1; + return sprintf(buf, "%d\n", bond->params.downdelay * bond->params.miimon); } static ssize_t bonding_store_downdelay(struct device *d, @@ -872,7 +851,7 @@ static ssize_t bonding_show_updelay(struct device *d, { struct bonding *bond = to_bond(d); - return sprintf(buf, "%d\n", bond->params.updelay * bond->params.miimon) + 1; + return sprintf(buf, "%d\n", bond->params.updelay * bond->params.miimon); } @@ -936,7 +915,7 @@ static ssize_t bonding_show_lacp(struct device *d, return sprintf(buf, "%s %d\n", bond_lacp_tbl[bond->params.lacp_fast].modename, - bond->params.lacp_fast) + 1; + bond->params.lacp_fast); } static ssize_t bonding_store_lacp(struct device *d, @@ -992,7 +971,7 @@ static ssize_t bonding_show_miimon(struct device *d, { struct bonding *bond = to_bond(d); - return sprintf(buf, "%d\n", bond->params.miimon) + 1; + return sprintf(buf, "%d\n", bond->params.miimon); } static ssize_t bonding_store_miimon(struct device *d, @@ -1083,9 +1062,7 @@ static ssize_t bonding_show_primary(struct device *d, struct bonding *bond = to_bond(d); if (bond->primary_slave) - count = sprintf(buf, "%s\n", bond->primary_slave->dev->name) + 1; - else - count = sprintf(buf, "\n") + 1; + count = sprintf(buf, "%s\n", bond->primary_slave->dev->name); return count; } @@ -1149,7 +1126,7 @@ static ssize_t bonding_show_carrier(struct device *d, { struct bonding *bond = to_bond(d); - return sprintf(buf, "%d\n", bond->params.use_carrier) + 1; + return sprintf(buf, "%d\n", bond->params.use_carrier); } static ssize_t bonding_store_carrier(struct device *d, @@ -1191,16 +1168,14 @@ static ssize_t bonding_show_active_slave(struct device *d, { struct slave *curr; struct bonding *bond = to_bond(d); - int count; + int count = 0; read_lock(&bond->curr_slave_lock); curr = bond->curr_active_slave; read_unlock(&bond->curr_slave_lock); if (USES_PRIMARY(bond->params.mode) && curr) - count = sprintf(buf, "%s\n", curr->dev->name) + 1; - else - count = sprintf(buf, "\n") + 1; + count = sprintf(buf, "%s\n", curr->dev->name); return count; } @@ -1295,7 +1270,7 @@ static ssize_t bonding_show_mii_status(struct device *d, curr = bond->curr_active_slave; read_unlock(&bond->curr_slave_lock); - return sprintf(buf, "%s\n", (curr) ? "up" : "down") + 1; + return sprintf(buf, "%s\n", (curr) ? "up" : "down"); } static DEVICE_ATTR(mii_status, S_IRUGO, bonding_show_mii_status, NULL); @@ -1312,10 +1287,8 @@ static ssize_t bonding_show_ad_aggregator(struct device *d, if (bond->params.mode == BOND_MODE_8023AD) { struct ad_info ad_info; - count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0 : ad_info.aggregator_id) + 1; + count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0 : ad_info.aggregator_id); } - else - count = sprintf(buf, "\n") + 1; return count; } @@ -1334,10 +1307,8 @@ static ssize_t bonding_show_ad_num_ports(struct device *d, if (bond->params.mode == BOND_MODE_8023AD) { struct ad_info ad_info; - count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0: ad_info.ports) + 1; + count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0: ad_info.ports); } - else - count = sprintf(buf, "\n") + 1; return count; } @@ -1356,10 +1327,8 @@ static ssize_t bonding_show_ad_actor_key(struct device *d, if (bond->params.mode == BOND_MODE_8023AD) { struct ad_info ad_info; - count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0 : ad_info.actor_key) + 1; + count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0 : ad_info.actor_key); } - else - count = sprintf(buf, "\n") + 1; return count; } @@ -1378,10 +1347,8 @@ static ssize_t bonding_show_ad_partner_key(struct device *d, if (bond->params.mode == BOND_MODE_8023AD) { struct ad_info ad_info; - count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0 : ad_info.partner_key) + 1; + count = sprintf(buf, "%d\n", (bond_3ad_get_active_agg_info(bond, &ad_info)) ? 0 : ad_info.partner_key); } - else - count = sprintf(buf, "\n") + 1; return count; } @@ -1403,12 +1370,9 @@ static ssize_t bonding_show_ad_partner_mac(struct device *d, struct ad_info ad_info; if (!bond_3ad_get_active_agg_info(bond, &ad_info)) { count = sprintf(buf,"%s\n", - print_mac(mac, ad_info.partner_system)) - + 1; + print_mac(mac, ad_info.partner_system)); } } - else - count = sprintf(buf, "\n") + 1; return count; } diff --git a/drivers/net/bonding/bonding.h b/drivers/net/bonding/bonding.h index 61c1b4536d34..e1e4734e23ce 100644 --- a/drivers/net/bonding/bonding.h +++ b/drivers/net/bonding/bonding.h @@ -22,8 +22,8 @@ #include "bond_3ad.h" #include "bond_alb.h" -#define DRV_VERSION "3.2.1" -#define DRV_RELDATE "October 15, 2007" +#define DRV_VERSION "3.2.3" +#define DRV_RELDATE "December 6, 2007" #define DRV_NAME "bonding" #define DRV_DESCRIPTION "Ethernet Channel Bonding Driver" diff --git a/drivers/net/chelsio/cxgb2.c b/drivers/net/chelsio/cxgb2.c index 2dbf8dc116c6..c5975047c89b 100644 --- a/drivers/net/chelsio/cxgb2.c +++ b/drivers/net/chelsio/cxgb2.c @@ -374,7 +374,9 @@ static char stats_strings[][ETH_GSTRING_LEN] = { "TxInternalMACXmitError", "TxFramesWithExcessiveDeferral", "TxFCSErrors", - + "TxJumboFramesOk", + "TxJumboOctetsOk", + "RxOctetsOK", "RxOctetsBad", "RxUnicastFramesOK", @@ -392,16 +394,17 @@ static char stats_strings[][ETH_GSTRING_LEN] = { "RxInRangeLengthErrors", "RxOutOfRangeLengthField", "RxFrameTooLongErrors", + "RxJumboFramesOk", + "RxJumboOctetsOk", /* Port stats */ - "RxPackets", "RxCsumGood", - "TxPackets", "TxCsumOffload", "TxTso", "RxVlan", "TxVlan", - + "TxNeedHeadroom", + /* Interrupt stats */ "rx drops", "pure_rsps", @@ -463,23 +466,56 @@ static void get_stats(struct net_device *dev, struct ethtool_stats *stats, const struct cmac_statistics *s; const struct sge_intr_counts *t; struct sge_port_stats ss; - unsigned int len; s = mac->ops->statistics_update(mac, MAC_STATS_UPDATE_FULL); - - len = sizeof(u64)*(&s->TxFCSErrors + 1 - &s->TxOctetsOK); - memcpy(data, &s->TxOctetsOK, len); - data += len; - - len = sizeof(u64)*(&s->RxFrameTooLongErrors + 1 - &s->RxOctetsOK); - memcpy(data, &s->RxOctetsOK, len); - data += len; - + t = t1_sge_get_intr_counts(adapter->sge); t1_sge_get_port_stats(adapter->sge, dev->if_port, &ss); - memcpy(data, &ss, sizeof(ss)); - data += sizeof(ss); - t = t1_sge_get_intr_counts(adapter->sge); + *data++ = s->TxOctetsOK; + *data++ = s->TxOctetsBad; + *data++ = s->TxUnicastFramesOK; + *data++ = s->TxMulticastFramesOK; + *data++ = s->TxBroadcastFramesOK; + *data++ = s->TxPauseFrames; + *data++ = s->TxFramesWithDeferredXmissions; + *data++ = s->TxLateCollisions; + *data++ = s->TxTotalCollisions; + *data++ = s->TxFramesAbortedDueToXSCollisions; + *data++ = s->TxUnderrun; + *data++ = s->TxLengthErrors; + *data++ = s->TxInternalMACXmitError; + *data++ = s->TxFramesWithExcessiveDeferral; + *data++ = s->TxFCSErrors; + *data++ = s->TxJumboFramesOK; + *data++ = s->TxJumboOctetsOK; + + *data++ = s->RxOctetsOK; + *data++ = s->RxOctetsBad; + *data++ = s->RxUnicastFramesOK; + *data++ = s->RxMulticastFramesOK; + *data++ = s->RxBroadcastFramesOK; + *data++ = s->RxPauseFrames; + *data++ = s->RxFCSErrors; + *data++ = s->RxAlignErrors; + *data++ = s->RxSymbolErrors; + *data++ = s->RxDataErrors; + *data++ = s->RxSequenceErrors; + *data++ = s->RxRuntErrors; + *data++ = s->RxJabberErrors; + *data++ = s->RxInternalMACRcvError; + *data++ = s->RxInRangeLengthErrors; + *data++ = s->RxOutOfRangeLengthField; + *data++ = s->RxFrameTooLongErrors; + *data++ = s->RxJumboFramesOK; + *data++ = s->RxJumboOctetsOK; + + *data++ = ss.rx_cso_good; + *data++ = ss.tx_cso; + *data++ = ss.tx_tso; + *data++ = ss.vlan_xtract; + *data++ = ss.vlan_insert; + *data++ = ss.tx_need_hdrroom; + *data++ = t->rx_drops; *data++ = t->pure_rsps; *data++ = t->unhandled_irqs; diff --git a/drivers/net/chelsio/pm3393.c b/drivers/net/chelsio/pm3393.c index 678778a8d133..2117c4fbb107 100644 --- a/drivers/net/chelsio/pm3393.c +++ b/drivers/net/chelsio/pm3393.c @@ -45,7 +45,7 @@ #include <linux/crc32.h> -#define OFFSET(REG_ADDR) (REG_ADDR << 2) +#define OFFSET(REG_ADDR) ((REG_ADDR) << 2) /* Max frame size PM3393 can handle. Includes Ethernet header and CRC. */ #define MAX_FRAME_SIZE 9600 @@ -428,69 +428,26 @@ static int pm3393_set_speed_duplex_fc(struct cmac *cmac, int speed, int duplex, return 0; } -static void pm3393_rmon_update(struct adapter *adapter, u32 offs, u64 *val, - int over) -{ - u32 val0, val1, val2; - - t1_tpi_read(adapter, offs, &val0); - t1_tpi_read(adapter, offs + 4, &val1); - t1_tpi_read(adapter, offs + 8, &val2); - - *val &= ~0ull << 40; - *val |= val0 & 0xffff; - *val |= (val1 & 0xffff) << 16; - *val |= (u64)(val2 & 0xff) << 32; - - if (over) - *val += 1ull << 40; +#define RMON_UPDATE(mac, name, stat_name) \ +{ \ + t1_tpi_read((mac)->adapter, OFFSET(name), &val0); \ + t1_tpi_read((mac)->adapter, OFFSET((name)+1), &val1); \ + t1_tpi_read((mac)->adapter, OFFSET((name)+2), &val2); \ + (mac)->stats.stat_name = (u64)(val0 & 0xffff) | \ + ((u64)(val1 & 0xffff) << 16) | \ + ((u64)(val2 & 0xff) << 32) | \ + ((mac)->stats.stat_name & \ + 0xffffff0000000000ULL); \ + if (ro & \ + (1ULL << ((name - SUNI1x10GEXP_REG_MSTAT_COUNTER_0_LOW) >> 2))) \ + (mac)->stats.stat_name += 1ULL << 40; \ } static const struct cmac_statistics *pm3393_update_statistics(struct cmac *mac, int flag) { - static struct { - unsigned int reg; - unsigned int offset; - } hw_stats [] = { - -#define HW_STAT(name, stat_name) \ - { name, (&((struct cmac_statistics *)NULL)->stat_name) - (u64 *)NULL } - - /* Rx stats */ - HW_STAT(RxOctetsReceivedOK, RxOctetsOK), - HW_STAT(RxUnicastFramesReceivedOK, RxUnicastFramesOK), - HW_STAT(RxMulticastFramesReceivedOK, RxMulticastFramesOK), - HW_STAT(RxBroadcastFramesReceivedOK, RxBroadcastFramesOK), - HW_STAT(RxPAUSEMACCtrlFramesReceived, RxPauseFrames), - HW_STAT(RxFrameCheckSequenceErrors, RxFCSErrors), - HW_STAT(RxFramesLostDueToInternalMACErrors, - RxInternalMACRcvError), - HW_STAT(RxSymbolErrors, RxSymbolErrors), - HW_STAT(RxInRangeLengthErrors, RxInRangeLengthErrors), - HW_STAT(RxFramesTooLongErrors , RxFrameTooLongErrors), - HW_STAT(RxJabbers, RxJabberErrors), - HW_STAT(RxFragments, RxRuntErrors), - HW_STAT(RxUndersizedFrames, RxRuntErrors), - HW_STAT(RxJumboFramesReceivedOK, RxJumboFramesOK), - HW_STAT(RxJumboOctetsReceivedOK, RxJumboOctetsOK), - - /* Tx stats */ - HW_STAT(TxOctetsTransmittedOK, TxOctetsOK), - HW_STAT(TxFramesLostDueToInternalMACTransmissionError, - TxInternalMACXmitError), - HW_STAT(TxTransmitSystemError, TxFCSErrors), - HW_STAT(TxUnicastFramesTransmittedOK, TxUnicastFramesOK), - HW_STAT(TxMulticastFramesTransmittedOK, TxMulticastFramesOK), - HW_STAT(TxBroadcastFramesTransmittedOK, TxBroadcastFramesOK), - HW_STAT(TxPAUSEMACCtrlFramesTransmitted, TxPauseFrames), - HW_STAT(TxJumboFramesReceivedOK, TxJumboFramesOK), - HW_STAT(TxJumboOctetsReceivedOK, TxJumboOctetsOK) - }, *p = hw_stats; - u64 ro; - u32 val0, val1, val2, val3; - u64 *stats = (u64 *) &mac->stats; - unsigned int i; + u64 ro; + u32 val0, val1, val2, val3; /* Snap the counters */ pmwrite(mac, SUNI1x10GEXP_REG_MSTAT_CONTROL, @@ -504,14 +461,35 @@ static const struct cmac_statistics *pm3393_update_statistics(struct cmac *mac, ro = ((u64)val0 & 0xffff) | (((u64)val1 & 0xffff) << 16) | (((u64)val2 & 0xffff) << 32) | (((u64)val3 & 0xffff) << 48); - for (i = 0; i < ARRAY_SIZE(hw_stats); i++) { - unsigned reg = p->reg - SUNI1x10GEXP_REG_MSTAT_COUNTER_0_LOW; - - pm3393_rmon_update((mac)->adapter, OFFSET(p->reg), - stats + p->offset, ro & (reg >> 2)); - } - - + /* Rx stats */ + RMON_UPDATE(mac, RxOctetsReceivedOK, RxOctetsOK); + RMON_UPDATE(mac, RxUnicastFramesReceivedOK, RxUnicastFramesOK); + RMON_UPDATE(mac, RxMulticastFramesReceivedOK, RxMulticastFramesOK); + RMON_UPDATE(mac, RxBroadcastFramesReceivedOK, RxBroadcastFramesOK); + RMON_UPDATE(mac, RxPAUSEMACCtrlFramesReceived, RxPauseFrames); + RMON_UPDATE(mac, RxFrameCheckSequenceErrors, RxFCSErrors); + RMON_UPDATE(mac, RxFramesLostDueToInternalMACErrors, + RxInternalMACRcvError); + RMON_UPDATE(mac, RxSymbolErrors, RxSymbolErrors); + RMON_UPDATE(mac, RxInRangeLengthErrors, RxInRangeLengthErrors); + RMON_UPDATE(mac, RxFramesTooLongErrors , RxFrameTooLongErrors); + RMON_UPDATE(mac, RxJabbers, RxJabberErrors); + RMON_UPDATE(mac, RxFragments, RxRuntErrors); + RMON_UPDATE(mac, RxUndersizedFrames, RxRuntErrors); + RMON_UPDATE(mac, RxJumboFramesReceivedOK, RxJumboFramesOK); + RMON_UPDATE(mac, RxJumboOctetsReceivedOK, RxJumboOctetsOK); + + /* Tx stats */ + RMON_UPDATE(mac, TxOctetsTransmittedOK, TxOctetsOK); + RMON_UPDATE(mac, TxFramesLostDueToInternalMACTransmissionError, + TxInternalMACXmitError); + RMON_UPDATE(mac, TxTransmitSystemError, TxFCSErrors); + RMON_UPDATE(mac, TxUnicastFramesTransmittedOK, TxUnicastFramesOK); + RMON_UPDATE(mac, TxMulticastFramesTransmittedOK, TxMulticastFramesOK); + RMON_UPDATE(mac, TxBroadcastFramesTransmittedOK, TxBroadcastFramesOK); + RMON_UPDATE(mac, TxPAUSEMACCtrlFramesTransmitted, TxPauseFrames); + RMON_UPDATE(mac, TxJumboFramesReceivedOK, TxJumboFramesOK); + RMON_UPDATE(mac, TxJumboOctetsReceivedOK, TxJumboOctetsOK); return &mac->stats; } diff --git a/drivers/net/chelsio/sge.c b/drivers/net/chelsio/sge.c index 443666292a5c..b301c0428ae0 100644 --- a/drivers/net/chelsio/sge.c +++ b/drivers/net/chelsio/sge.c @@ -986,11 +986,10 @@ void t1_sge_get_port_stats(const struct sge *sge, int port, for_each_possible_cpu(cpu) { struct sge_port_stats *st = per_cpu_ptr(sge->port_stats[port], cpu); - ss->rx_packets += st->rx_packets; ss->rx_cso_good += st->rx_cso_good; - ss->tx_packets += st->tx_packets; ss->tx_cso += st->tx_cso; ss->tx_tso += st->tx_tso; + ss->tx_need_hdrroom += st->tx_need_hdrroom; ss->vlan_xtract += st->vlan_xtract; ss->vlan_insert += st->vlan_insert; } @@ -1380,7 +1379,6 @@ static void sge_rx(struct sge *sge, struct freelQ *fl, unsigned int len) __skb_pull(skb, sizeof(*p)); st = per_cpu_ptr(sge->port_stats[p->iff], smp_processor_id()); - st->rx_packets++; skb->protocol = eth_type_trans(skb, adapter->port[p->iff].dev); skb->dev->last_rx = jiffies; @@ -1624,11 +1622,9 @@ int t1_poll(struct napi_struct *napi, int budget) { struct adapter *adapter = container_of(napi, struct adapter, napi); struct net_device *dev = adapter->port[0].dev; - int work_done; - - work_done = process_responses(adapter, budget); + int work_done = process_responses(adapter, budget); - if (likely(!responses_pending(adapter))) { + if (likely(work_done < budget)) { netif_rx_complete(dev, napi); writel(adapter->sge->respQ.cidx, adapter->regs + A_SG_SLEEPING); @@ -1848,7 +1844,8 @@ int t1_start_xmit(struct sk_buff *skb, struct net_device *dev) { struct adapter *adapter = dev->priv; struct sge *sge = adapter->sge; - struct sge_port_stats *st = per_cpu_ptr(sge->port_stats[dev->if_port], smp_processor_id()); + struct sge_port_stats *st = per_cpu_ptr(sge->port_stats[dev->if_port], + smp_processor_id()); struct cpl_tx_pkt *cpl; struct sk_buff *orig_skb = skb; int ret; @@ -1856,6 +1853,18 @@ int t1_start_xmit(struct sk_buff *skb, struct net_device *dev) if (skb->protocol == htons(ETH_P_CPL5)) goto send; + /* + * We are using a non-standard hard_header_len. + * Allocate more header room in the rare cases it is not big enough. + */ + if (unlikely(skb_headroom(skb) < dev->hard_header_len - ETH_HLEN)) { + skb = skb_realloc_headroom(skb, sizeof(struct cpl_tx_pkt_lso)); + ++st->tx_need_hdrroom; + dev_kfree_skb_any(orig_skb); + if (!skb) + return NETDEV_TX_OK; + } + if (skb_shinfo(skb)->gso_size) { int eth_type; struct cpl_tx_pkt_lso *hdr; @@ -1889,24 +1898,6 @@ int t1_start_xmit(struct sk_buff *skb, struct net_device *dev) return NETDEV_TX_OK; } - /* - * We are using a non-standard hard_header_len and some kernel - * components, such as pktgen, do not handle it right. - * Complain when this happens but try to fix things up. - */ - if (unlikely(skb_headroom(skb) < dev->hard_header_len - ETH_HLEN)) { - pr_debug("%s: headroom %d header_len %d\n", dev->name, - skb_headroom(skb), dev->hard_header_len); - - if (net_ratelimit()) - printk(KERN_ERR "%s: inadequate headroom in " - "Tx packet\n", dev->name); - skb = skb_realloc_headroom(skb, sizeof(*cpl)); - dev_kfree_skb_any(orig_skb); - if (!skb) - return NETDEV_TX_OK; - } - if (!(adapter->flags & UDP_CSUM_CAPABLE) && skb->ip_summed == CHECKSUM_PARTIAL && ip_hdr(skb)->protocol == IPPROTO_UDP) { @@ -1952,7 +1943,6 @@ int t1_start_xmit(struct sk_buff *skb, struct net_device *dev) cpl->vlan_valid = 0; send: - st->tx_packets++; dev->trans_start = jiffies; ret = t1_sge_tx(skb, adapter, 0, dev); diff --git a/drivers/net/chelsio/sge.h b/drivers/net/chelsio/sge.h index 713d9c55f24d..cced9dff91c5 100644 --- a/drivers/net/chelsio/sge.h +++ b/drivers/net/chelsio/sge.h @@ -57,13 +57,12 @@ struct sge_intr_counts { }; struct sge_port_stats { - u64 rx_packets; /* # of Ethernet packets received */ u64 rx_cso_good; /* # of successful RX csum offloads */ - u64 tx_packets; /* # of TX packets */ u64 tx_cso; /* # of TX checksum offloads */ u64 tx_tso; /* # of TSO requests */ u64 vlan_xtract; /* # of VLAN tag extractions */ u64 vlan_insert; /* # of VLAN tag insertions */ + u64 tx_need_hdrroom; /* # of TX skbs in need of more header room */ }; struct sk_buff; diff --git a/drivers/net/cxgb3/regs.h b/drivers/net/cxgb3/regs.h index 5e1bc0dec5f1..6e12bf4bc6cf 100644 --- a/drivers/net/cxgb3/regs.h +++ b/drivers/net/cxgb3/regs.h @@ -1937,6 +1937,10 @@ #define A_XGM_RXFIFO_CFG 0x884 +#define S_RXFIFO_EMPTY 31 +#define V_RXFIFO_EMPTY(x) ((x) << S_RXFIFO_EMPTY) +#define F_RXFIFO_EMPTY V_RXFIFO_EMPTY(1U) + #define S_RXFIFOPAUSEHWM 17 #define M_RXFIFOPAUSEHWM 0xfff @@ -1961,6 +1965,10 @@ #define A_XGM_TXFIFO_CFG 0x888 +#define S_UNDERUNFIX 22 +#define V_UNDERUNFIX(x) ((x) << S_UNDERUNFIX) +#define F_UNDERUNFIX V_UNDERUNFIX(1U) + #define S_TXIPG 13 #define M_TXIPG 0xff #define V_TXIPG(x) ((x) << S_TXIPG) @@ -2034,10 +2042,27 @@ #define V_XAUIIMP(x) ((x) << S_XAUIIMP) #define A_XGM_RX_MAX_PKT_SIZE 0x8a8 -#define A_XGM_RX_MAX_PKT_SIZE_ERR_CNT 0x9a4 + +#define S_RXMAXFRAMERSIZE 17 +#define M_RXMAXFRAMERSIZE 0x3fff +#define V_RXMAXFRAMERSIZE(x) ((x) << S_RXMAXFRAMERSIZE) +#define G_RXMAXFRAMERSIZE(x) (((x) >> S_RXMAXFRAMERSIZE) & M_RXMAXFRAMERSIZE) + +#define S_RXENFRAMER 14 +#define V_RXENFRAMER(x) ((x) << S_RXENFRAMER) +#define F_RXENFRAMER V_RXENFRAMER(1U) + +#define S_RXMAXPKTSIZE 0 +#define M_RXMAXPKTSIZE 0x3fff +#define V_RXMAXPKTSIZE(x) ((x) << S_RXMAXPKTSIZE) +#define G_RXMAXPKTSIZE(x) (((x) >> S_RXMAXPKTSIZE) & M_RXMAXPKTSIZE) #define A_XGM_RESET_CTRL 0x8ac +#define S_XGMAC_STOP_EN 4 +#define V_XGMAC_STOP_EN(x) ((x) << S_XGMAC_STOP_EN) +#define F_XGMAC_STOP_EN V_XGMAC_STOP_EN(1U) + #define S_XG2G_RESET_ 3 #define V_XG2G_RESET_(x) ((x) << S_XG2G_RESET_) #define F_XG2G_RESET_ V_XG2G_RESET_(1U) diff --git a/drivers/net/cxgb3/t3_hw.c b/drivers/net/cxgb3/t3_hw.c index d4ee00d32219..522834c42ae7 100644 --- a/drivers/net/cxgb3/t3_hw.c +++ b/drivers/net/cxgb3/t3_hw.c @@ -447,8 +447,8 @@ static const struct adapter_info t3_adap_info[] = { &mi1_mdio_ops, "Chelsio T302"}, {1, 0, 0, 0, F_GPIO1_OEN | F_GPIO6_OEN | F_GPIO7_OEN | F_GPIO10_OEN | - F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, 0, - SUPPORTED_10000baseT_Full | SUPPORTED_AUI, + F_GPIO11_OEN | F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL, + 0, SUPPORTED_10000baseT_Full | SUPPORTED_AUI, &mi1_mdio_ext_ops, "Chelsio T310"}, {2, 0, 0, 0, F_GPIO1_OEN | F_GPIO2_OEN | F_GPIO4_OEN | F_GPIO5_OEN | F_GPIO6_OEN | @@ -2613,7 +2613,7 @@ static void __devinit init_mtus(unsigned short mtus[]) * it can accomodate max size TCP/IP headers when SACK and timestamps * are enabled and still have at least 8 bytes of payload. */ - mtus[1] = 88; + mtus[0] = 88; mtus[1] = 88; mtus[2] = 256; mtus[3] = 512; diff --git a/drivers/net/cxgb3/xgmac.c b/drivers/net/cxgb3/xgmac.c index eeb766aeced9..efcf09a709cf 100644 --- a/drivers/net/cxgb3/xgmac.c +++ b/drivers/net/cxgb3/xgmac.c @@ -106,6 +106,7 @@ int t3_mac_reset(struct cmac *mac) t3_set_reg_field(adap, A_XGM_RXFIFO_CFG + oft, F_RXSTRFRWRD | F_DISERRFRAMES, uses_xaui(adap) ? 0 : F_RXSTRFRWRD); + t3_set_reg_field(adap, A_XGM_TXFIFO_CFG + oft, 0, F_UNDERUNFIX); if (uses_xaui(adap)) { if (adap->params.rev == 0) { @@ -124,7 +125,11 @@ int t3_mac_reset(struct cmac *mac) xaui_serdes_reset(mac); } - val = F_MAC_RESET_; + t3_set_reg_field(adap, A_XGM_RX_MAX_PKT_SIZE + oft, + V_RXMAXFRAMERSIZE(M_RXMAXFRAMERSIZE), + V_RXMAXFRAMERSIZE(MAX_FRAME_SIZE) | F_RXENFRAMER); + val = F_MAC_RESET_ | F_XGMAC_STOP_EN; + if (is_10G(adap)) val |= F_PCS_RESET_; else if (uses_xaui(adap)) @@ -313,8 +318,9 @@ static int rx_fifo_hwm(int mtu) int t3_mac_set_mtu(struct cmac *mac, unsigned int mtu) { - int hwm, lwm; - unsigned int thres, v; + int hwm, lwm, divisor; + int ipg; + unsigned int thres, v, reg; struct adapter *adap = mac->adapter; /* @@ -335,27 +341,32 @@ int t3_mac_set_mtu(struct cmac *mac, unsigned int mtu) hwm = min(hwm, MAC_RXFIFO_SIZE - 8192); lwm = min(3 * (int)mtu, MAC_RXFIFO_SIZE / 4); - if (adap->params.rev == T3_REV_B2 && + if (adap->params.rev >= T3_REV_B2 && (t3_read_reg(adap, A_XGM_RX_CTRL + mac->offset) & F_RXEN)) { disable_exact_filters(mac); v = t3_read_reg(adap, A_XGM_RX_CFG + mac->offset); t3_set_reg_field(adap, A_XGM_RX_CFG + mac->offset, F_ENHASHMCAST | F_COPYALLFRAMES, F_DISBCAST); - /* drain rx FIFO */ - if (t3_wait_op_done(adap, - A_XGM_RX_MAX_PKT_SIZE_ERR_CNT + - mac->offset, - 1 << 31, 1, 20, 5)) { + reg = adap->params.rev == T3_REV_B2 ? + A_XGM_RX_MAX_PKT_SIZE_ERR_CNT : A_XGM_RXFIFO_CFG; + + /* drain RX FIFO */ + if (t3_wait_op_done(adap, reg + mac->offset, + F_RXFIFO_EMPTY, 1, 20, 5)) { t3_write_reg(adap, A_XGM_RX_CFG + mac->offset, v); enable_exact_filters(mac); return -EIO; } - t3_write_reg(adap, A_XGM_RX_MAX_PKT_SIZE + mac->offset, mtu); + t3_set_reg_field(adap, A_XGM_RX_MAX_PKT_SIZE + mac->offset, + V_RXMAXPKTSIZE(M_RXMAXPKTSIZE), + V_RXMAXPKTSIZE(mtu)); t3_write_reg(adap, A_XGM_RX_CFG + mac->offset, v); enable_exact_filters(mac); } else - t3_write_reg(adap, A_XGM_RX_MAX_PKT_SIZE + mac->offset, mtu); + t3_set_reg_field(adap, A_XGM_RX_MAX_PKT_SIZE + mac->offset, + V_RXMAXPKTSIZE(M_RXMAXPKTSIZE), + V_RXMAXPKTSIZE(mtu)); /* * Adjust the PAUSE frame watermarks. We always set the LWM, and the @@ -379,13 +390,16 @@ int t3_mac_set_mtu(struct cmac *mac, unsigned int mtu) thres /= 10; thres = mtu > thres ? (mtu - thres + 7) / 8 : 0; thres = max(thres, 8U); /* need at least 8 */ + ipg = (adap->params.rev == T3_REV_C) ? 0 : 1; t3_set_reg_field(adap, A_XGM_TXFIFO_CFG + mac->offset, V_TXFIFOTHRESH(M_TXFIFOTHRESH) | V_TXIPG(M_TXIPG), - V_TXFIFOTHRESH(thres) | V_TXIPG(1)); + V_TXFIFOTHRESH(thres) | V_TXIPG(ipg)); - if (adap->params.rev > 0) + if (adap->params.rev > 0) { + divisor = (adap->params.rev == T3_REV_C) ? 64 : 8; t3_write_reg(adap, A_XGM_PAUSE_TIMER + mac->offset, - (hwm - lwm) * 4 / 8); + (hwm - lwm) * 4 / divisor); + } t3_write_reg(adap, A_XGM_TX_PAUSE_QUANTA + mac->offset, MAC_RXFIFO_SIZE * 4 * 8 / 512); return 0; @@ -522,7 +536,7 @@ int t3b2_mac_watchdog_task(struct cmac *mac) goto rxcheck; } - if ((tx_tcnt != mac->tx_tcnt) && (mac->tx_xcnt == 0)) { + if ((tx_tcnt != mac->tx_tcnt) && (mac->tx_xcnt == 0)) { if (mac->toggle_cnt > 4) { status = 2; goto out; diff --git a/drivers/net/e100.c b/drivers/net/e100.c index 3dbaec680b46..e1c8a0d023ea 100644 --- a/drivers/net/e100.c +++ b/drivers/net/e100.c @@ -2214,13 +2214,11 @@ static void e100_get_drvinfo(struct net_device *netdev, strcpy(info->bus_info, pci_name(nic->pdev)); } +#define E100_PHY_REGS 0x1C static int e100_get_regs_len(struct net_device *netdev) { struct nic *nic = netdev_priv(netdev); -#define E100_PHY_REGS 0x1C -#define E100_REGS_LEN 1 + E100_PHY_REGS + \ - sizeof(nic->mem->dump_buf) / sizeof(u32) - return E100_REGS_LEN * sizeof(u32); + return 1 + E100_PHY_REGS + sizeof(nic->mem->dump_buf); } static void e100_get_regs(struct net_device *netdev, diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c index 667f18bcc172..b83ccce8a9b7 100644 --- a/drivers/net/e1000/e1000_ethtool.c +++ b/drivers/net/e1000/e1000_ethtool.c @@ -1923,7 +1923,7 @@ e1000_get_strings(struct net_device *netdev, uint32_t stringset, uint8_t *data) switch (stringset) { case ETH_SS_TEST: memcpy(data, *e1000_gstrings_test, - E1000_TEST_LEN*ETH_GSTRING_LEN); + sizeof(e1000_gstrings_test)); break; case ETH_SS_STATS: for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) { diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index cf39473ef90a..4f37506ad374 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -3942,7 +3942,7 @@ e1000_clean(struct napi_struct *napi, int budget) &work_done, budget); /* If no Tx and not enough Rx work done, exit the polling mode */ - if ((!tx_cleaned && (work_done < budget)) || + if ((!tx_cleaned && (work_done == 0)) || !netif_running(poll_dev)) { quit_polling: if (likely(adapter->itr_setting & 3)) diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c index 6a39784e7ee2..87f9da1b6b4e 100644 --- a/drivers/net/e1000e/ethtool.c +++ b/drivers/net/e1000e/ethtool.c @@ -1739,7 +1739,7 @@ static void e1000_get_strings(struct net_device *netdev, u32 stringset, switch (stringset) { case ETH_SS_TEST: memcpy(data, *e1000_gstrings_test, - E1000_TEST_LEN*ETH_GSTRING_LEN); + sizeof(e1000_gstrings_test)); break; case ETH_SS_STATS: for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) { diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h index f78e5bf7cb33..5f82a4647eee 100644 --- a/drivers/net/ehea/ehea.h +++ b/drivers/net/ehea/ehea.h @@ -40,7 +40,7 @@ #include <asm/io.h> #define DRV_NAME "ehea" -#define DRV_VERSION "EHEA_0080" +#define DRV_VERSION "EHEA_0083" /* eHEA capability flags */ #define DLPAR_PORT_ADD_REM 1 diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c index f0319f1e8e05..869e1604b16e 100644 --- a/drivers/net/ehea/ehea_main.c +++ b/drivers/net/ehea/ehea_main.c @@ -136,7 +136,7 @@ static struct net_device_stats *ehea_get_stats(struct net_device *dev) struct ehea_port *port = netdev_priv(dev); struct net_device_stats *stats = &port->stats; struct hcp_ehea_port_cb2 *cb2; - u64 hret, rx_packets; + u64 hret, rx_packets, tx_packets; int i; memset(stats, 0, sizeof(*stats)); @@ -162,7 +162,11 @@ static struct net_device_stats *ehea_get_stats(struct net_device *dev) for (i = 0; i < port->num_def_qps; i++) rx_packets += port->port_res[i].rx_packets; - stats->tx_packets = cb2->txucp + cb2->txmcp + cb2->txbcp; + tx_packets = 0; + for (i = 0; i < port->num_def_qps + port->num_add_tx_qps; i++) + tx_packets += port->port_res[i].tx_packets; + + stats->tx_packets = tx_packets; stats->multicast = cb2->rxmcp; stats->rx_errors = cb2->rxuerr; stats->rx_bytes = cb2->rxo; @@ -406,11 +410,6 @@ static int ehea_treat_poll_error(struct ehea_port_res *pr, int rq, if (cqe->status & EHEA_CQE_STAT_ERR_CRC) pr->p_stats.err_frame_crc++; - if (netif_msg_rx_err(pr->port)) { - ehea_error("CQE Error for QP %d", pr->qp->init_attr.qp_nr); - ehea_dump(cqe, sizeof(*cqe), "CQE"); - } - if (rq == 2) { *processed_rq2 += 1; skb = get_skb_by_index(pr->rq2_skba.arr, pr->rq2_skba.len, cqe); @@ -422,7 +421,11 @@ static int ehea_treat_poll_error(struct ehea_port_res *pr, int rq, } if (cqe->status & EHEA_CQE_STAT_FAT_ERR_MASK) { - ehea_error("Critical receive error. Resetting port."); + if (netif_msg_rx_err(pr->port)) { + ehea_error("Critical receive error for QP %d. " + "Resetting port.", pr->qp->init_attr.qp_nr); + ehea_dump(cqe, sizeof(*cqe), "CQE"); + } schedule_work(&pr->port->reset_task); return 1; } @@ -2000,6 +2003,7 @@ static int ehea_start_xmit(struct sk_buff *skb, struct net_device *dev) } ehea_post_swqe(pr->qp, swqe); + pr->tx_packets++; if (unlikely(atomic_read(&pr->swqe_avail) <= 1)) { spin_lock_irqsave(&pr->netif_queue, flags); diff --git a/drivers/net/ehea/ehea_qmr.h b/drivers/net/ehea/ehea_qmr.h index 562de0ebdd85..bc62d389c166 100644 --- a/drivers/net/ehea/ehea_qmr.h +++ b/drivers/net/ehea/ehea_qmr.h @@ -145,8 +145,8 @@ struct ehea_rwqe { #define EHEA_CQE_VLAN_TAG_XTRACT 0x0400 #define EHEA_CQE_TYPE_RQ 0x60 -#define EHEA_CQE_STAT_ERR_MASK 0x720F -#define EHEA_CQE_STAT_FAT_ERR_MASK 0x1F +#define EHEA_CQE_STAT_ERR_MASK 0x700F +#define EHEA_CQE_STAT_FAT_ERR_MASK 0xF #define EHEA_CQE_STAT_ERR_TCP 0x4000 #define EHEA_CQE_STAT_ERR_IP 0x2000 #define EHEA_CQE_STAT_ERR_CRC 0x1000 diff --git a/drivers/net/fec_mpc52xx.c b/drivers/net/fec_mpc52xx.c index a8a0ee220da6..79f7eade4773 100644 --- a/drivers/net/fec_mpc52xx.c +++ b/drivers/net/fec_mpc52xx.c @@ -422,7 +422,7 @@ static irqreturn_t mpc52xx_fec_rx_interrupt(int irq, void *dev_id) rskb = bcom_retrieve_buffer(priv->rx_dmatsk, &status, (struct bcom_bd **)&bd); - dma_unmap_single(&dev->dev, bd->skb_pa, skb->len, DMA_FROM_DEVICE); + dma_unmap_single(&dev->dev, bd->skb_pa, rskb->len, DMA_FROM_DEVICE); /* Test for errors in received frame */ if (status & BCOM_FEC_RX_BD_ERRORS) { @@ -467,7 +467,7 @@ static irqreturn_t mpc52xx_fec_rx_interrupt(int irq, void *dev_id) bcom_prepare_next_buffer(priv->rx_dmatsk); bd->status = FEC_RX_BUFFER_SIZE; - bd->skb_pa = dma_map_single(&dev->dev, rskb->data, + bd->skb_pa = dma_map_single(&dev->dev, skb->data, FEC_RX_BUFFER_SIZE, DMA_FROM_DEVICE); bcom_submit_next_buffer(priv->rx_dmatsk, skb); @@ -971,6 +971,8 @@ mpc52xx_fec_probe(struct of_device *op, const struct of_device_id *match) mpc52xx_fec_reset_stats(ndev); + SET_NETDEV_DEV(ndev, &op->dev); + /* Register the new network device */ rv = register_netdev(ndev); if (rv < 0) diff --git a/drivers/net/forcedeth.c b/drivers/net/forcedeth.c index 92ce2e38f0d5..a96583cceb5e 100644 --- a/drivers/net/forcedeth.c +++ b/drivers/net/forcedeth.c @@ -5286,19 +5286,15 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i if (readl(base + NvRegTransmitterControl) & NVREG_XMITCTL_SYNC_PHY_INIT) { np->mac_in_use = readl(base + NvRegTransmitterControl) & NVREG_XMITCTL_MGMT_ST; dprintk(KERN_INFO "%s: mgmt unit is running. mac in use %x.\n", pci_name(pci_dev), np->mac_in_use); - for (i = 0; i < 5000; i++) { - msleep(1); - if (nv_mgmt_acquire_sema(dev)) { - /* management unit setup the phy already? */ - if ((readl(base + NvRegTransmitterControl) & NVREG_XMITCTL_SYNC_MASK) == - NVREG_XMITCTL_SYNC_PHY_INIT) { - /* phy is inited by mgmt unit */ - phyinitialized = 1; - dprintk(KERN_INFO "%s: Phy already initialized by mgmt unit.\n", pci_name(pci_dev)); - } else { - /* we need to init the phy */ - } - break; + if (nv_mgmt_acquire_sema(dev)) { + /* management unit setup the phy already? */ + if ((readl(base + NvRegTransmitterControl) & NVREG_XMITCTL_SYNC_MASK) == + NVREG_XMITCTL_SYNC_PHY_INIT) { + /* phy is inited by mgmt unit */ + phyinitialized = 1; + dprintk(KERN_INFO "%s: Phy already initialized by mgmt unit.\n", pci_name(pci_dev)); + } else { + /* we need to init the phy */ } } } @@ -5613,6 +5609,22 @@ static struct pci_device_id pci_tbl[] = { PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_35), .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT, }, + { /* MCP79 Ethernet Controller */ + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_36), + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT, + }, + { /* MCP79 Ethernet Controller */ + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_37), + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT, + }, + { /* MCP79 Ethernet Controller */ + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_38), + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT, + }, + { /* MCP79 Ethernet Controller */ + PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NVENET_39), + .driver_data = DEV_NEED_TIMERIRQ|DEV_NEED_LINKTIMER|DEV_HAS_CHECKSUM|DEV_HAS_HIGH_DMA|DEV_HAS_MSI|DEV_HAS_POWER_CNTRL|DEV_HAS_PAUSEFRAME_TX|DEV_HAS_STATISTICS_V2|DEV_HAS_TEST_EXTENDED|DEV_HAS_MGMT_UNIT, + }, {0,}, }; diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index 38268d7335a8..0431e9ed0fac 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -696,7 +696,7 @@ int startup_gfar(struct net_device *dev) { struct txbd8 *txbdp; struct rxbd8 *rxbdp; - dma_addr_t addr; + dma_addr_t addr = 0; unsigned long vaddr; int i; struct gfar_private *priv = netdev_priv(dev); diff --git a/drivers/net/ibm_newemac/core.c b/drivers/net/ibm_newemac/core.c index 0de3aa2a2e44..cb06280dced5 100644 --- a/drivers/net/ibm_newemac/core.c +++ b/drivers/net/ibm_newemac/core.c @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * @@ -402,7 +407,7 @@ static u32 __emac_calc_base_mr1(struct emac_instance *dev, int tx_size, int rx_s static u32 __emac4_calc_base_mr1(struct emac_instance *dev, int tx_size, int rx_size) { u32 ret = EMAC_MR1_VLE | EMAC_MR1_IST | EMAC4_MR1_TR | - EMAC4_MR1_OBCI(dev->opb_bus_freq); + EMAC4_MR1_OBCI(dev->opb_bus_freq / 1000000); DBG2(dev, "__emac4_calc_base_mr1" NL); @@ -464,26 +469,34 @@ static int emac_configure(struct emac_instance *dev) { struct emac_regs __iomem *p = dev->emacp; struct net_device *ndev = dev->ndev; - int tx_size, rx_size; + int tx_size, rx_size, link = netif_carrier_ok(dev->ndev); u32 r, mr1 = 0; DBG(dev, "configure" NL); - if (emac_reset(dev) < 0) + if (!link) { + out_be32(&p->mr1, in_be32(&p->mr1) + | EMAC_MR1_FDE | EMAC_MR1_ILE); + udelay(100); + } else if (emac_reset(dev) < 0) return -ETIMEDOUT; if (emac_has_feature(dev, EMAC_FTR_HAS_TAH)) tah_reset(dev->tah_dev); - DBG(dev, " duplex = %d, pause = %d, asym_pause = %d\n", - dev->phy.duplex, dev->phy.pause, dev->phy.asym_pause); + DBG(dev, " link = %d duplex = %d, pause = %d, asym_pause = %d\n", + link, dev->phy.duplex, dev->phy.pause, dev->phy.asym_pause); /* Default fifo sizes */ tx_size = dev->tx_fifo_size; rx_size = dev->rx_fifo_size; + /* No link, force loopback */ + if (!link) + mr1 = EMAC_MR1_FDE | EMAC_MR1_ILE; + /* Check for full duplex */ - if (dev->phy.duplex == DUPLEX_FULL) + else if (dev->phy.duplex == DUPLEX_FULL) mr1 |= EMAC_MR1_FDE | EMAC_MR1_MWSW_001; /* Adjust fifo sizes, mr1 and timeouts based on link speed */ @@ -642,9 +655,11 @@ static void emac_reset_work(struct work_struct *work) DBG(dev, "reset_work" NL); mutex_lock(&dev->link_lock); - emac_netif_stop(dev); - emac_full_tx_reset(dev); - emac_netif_start(dev); + if (dev->opened) { + emac_netif_stop(dev); + emac_full_tx_reset(dev); + emac_netif_start(dev); + } mutex_unlock(&dev->link_lock); } @@ -701,7 +716,7 @@ static int __emac_mdio_read(struct emac_instance *dev, u8 id, u8 reg) r = EMAC_STACR_BASE(dev->opb_bus_freq); if (emac_has_feature(dev, EMAC_FTR_STACR_OC_INVERT)) r |= EMAC_STACR_OC; - if (emac_has_feature(dev, EMAC_FTR_HAS_AXON_STACR)) + if (emac_has_feature(dev, EMAC_FTR_HAS_NEW_STACR)) r |= EMACX_STACR_STAC_READ; else r |= EMAC_STACR_STAC_READ; @@ -773,7 +788,7 @@ static void __emac_mdio_write(struct emac_instance *dev, u8 id, u8 reg, r = EMAC_STACR_BASE(dev->opb_bus_freq); if (emac_has_feature(dev, EMAC_FTR_STACR_OC_INVERT)) r |= EMAC_STACR_OC; - if (emac_has_feature(dev, EMAC_FTR_HAS_AXON_STACR)) + if (emac_has_feature(dev, EMAC_FTR_HAS_NEW_STACR)) r |= EMACX_STACR_STAC_WRITE; else r |= EMAC_STACR_STAC_WRITE; @@ -1063,10 +1078,9 @@ static int emac_open(struct net_device *ndev) dev->rx_sg_skb = NULL; mutex_lock(&dev->link_lock); + dev->opened = 1; - /* XXX Start PHY polling now. Shouldn't wr do like sungem instead and - * always poll the PHY even when the iface is down ? That would allow - * things like laptop-net to work. --BenH + /* Start PHY polling now. */ if (dev->phy.address >= 0) { int link_poll_interval; @@ -1145,9 +1159,11 @@ static void emac_link_timer(struct work_struct *work) int link_poll_interval; mutex_lock(&dev->link_lock); - DBG2(dev, "link timer" NL); + if (!dev->opened) + goto bail; + if (dev->phy.def->ops->poll_link(&dev->phy)) { if (!netif_carrier_ok(dev->ndev)) { /* Get new link parameters */ @@ -1162,21 +1178,22 @@ static void emac_link_timer(struct work_struct *work) link_poll_interval = PHY_POLL_LINK_ON; } else { if (netif_carrier_ok(dev->ndev)) { - emac_reinitialize(dev); netif_carrier_off(dev->ndev); netif_tx_disable(dev->ndev); + emac_reinitialize(dev); emac_print_link_status(dev); } link_poll_interval = PHY_POLL_LINK_OFF; } schedule_delayed_work(&dev->link_work, link_poll_interval); - + bail: mutex_unlock(&dev->link_lock); } static void emac_force_link_update(struct emac_instance *dev) { netif_carrier_off(dev->ndev); + smp_rmb(); if (dev->link_polling) { cancel_rearming_delayed_work(&dev->link_work); if (dev->link_polling) @@ -1191,11 +1208,14 @@ static int emac_close(struct net_device *ndev) DBG(dev, "close" NL); - if (dev->phy.address >= 0) + if (dev->phy.address >= 0) { + dev->link_polling = 0; cancel_rearming_delayed_work(&dev->link_work); - + } + mutex_lock(&dev->link_lock); emac_netif_stop(dev); - flush_scheduled_work(); + dev->opened = 0; + mutex_unlock(&dev->link_lock); emac_rx_disable(dev); emac_tx_disable(dev); @@ -2427,7 +2447,7 @@ static int __devinit emac_init_config(struct emac_instance *dev) if (emac_read_uint_prop(np, "tah-device", &dev->tah_ph, 0)) dev->tah_ph = 0; if (emac_read_uint_prop(np, "tah-channel", &dev->tah_port, 0)) - dev->tah_ph = 0; + dev->tah_port = 0; if (emac_read_uint_prop(np, "mdio-device", &dev->mdio_ph, 0)) dev->mdio_ph = 0; if (emac_read_uint_prop(np, "zmii-device", &dev->zmii_ph, 0)) @@ -2465,16 +2485,19 @@ static int __devinit emac_init_config(struct emac_instance *dev) /* Check EMAC version */ if (of_device_is_compatible(np, "ibm,emac4")) dev->features |= EMAC_FTR_EMAC4; - if (of_device_is_compatible(np, "ibm,emac-axon") - || of_device_is_compatible(np, "ibm,emac-440epx")) - dev->features |= EMAC_FTR_HAS_AXON_STACR - | EMAC_FTR_STACR_OC_INVERT; - if (of_device_is_compatible(np, "ibm,emac-440spe")) + + /* Fixup some feature bits based on the device tree */ + if (of_get_property(np, "has-inverted-stacr-oc", NULL)) dev->features |= EMAC_FTR_STACR_OC_INVERT; + if (of_get_property(np, "has-new-stacr-staopc", NULL)) + dev->features |= EMAC_FTR_HAS_NEW_STACR; - /* Fixup some feature bits based on the device tree and verify - * we have support for them compiled in - */ + /* CAB lacks the appropriate properties */ + if (of_device_is_compatible(np, "ibm,emac-axon")) + dev->features |= EMAC_FTR_HAS_NEW_STACR | + EMAC_FTR_STACR_OC_INVERT; + + /* Enable TAH/ZMII/RGMII features as found */ if (dev->tah_ph != 0) { #ifdef CONFIG_IBM_NEW_EMAC_TAH dev->features |= EMAC_FTR_HAS_TAH; @@ -2532,6 +2555,10 @@ static int __devinit emac_probe(struct of_device *ofdev, struct device_node **blist = NULL; int err, i; + /* Skip unused/unwired EMACS */ + if (of_get_property(np, "unused", NULL)) + return -ENODEV; + /* Find ourselves in the bootlist if we are there */ for (i = 0; i < EMAC_BOOT_LIST_SIZE; i++) if (emac_boot_list[i] == np) @@ -2756,6 +2783,8 @@ static int __devexit emac_remove(struct of_device *ofdev) unregister_netdev(dev->ndev); + flush_scheduled_work(); + if (emac_has_feature(dev, EMAC_FTR_HAS_TAH)) tah_detach(dev->tah_dev, dev->tah_port); if (emac_has_feature(dev, EMAC_FTR_HAS_RGMII)) diff --git a/drivers/net/ibm_newemac/core.h b/drivers/net/ibm_newemac/core.h index 4011803117ca..4e74d8287c65 100644 --- a/drivers/net/ibm_newemac/core.h +++ b/drivers/net/ibm_newemac/core.h @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * @@ -258,6 +263,7 @@ struct emac_instance { int stop_timeout; /* in us */ int no_mcast; int mcast_pending; + int opened; struct work_struct reset_work; spinlock_t lock; }; @@ -292,9 +298,9 @@ struct emac_instance { */ #define EMAC_FTR_HAS_RGMII 0x00000020 /* - * Set if we have axon-type STACR + * Set if we have new type STACR with STAOPC */ -#define EMAC_FTR_HAS_AXON_STACR 0x00000040 +#define EMAC_FTR_HAS_NEW_STACR 0x00000040 /* Right now, we don't quite handle the always/possible masks on the @@ -306,7 +312,7 @@ enum { EMAC_FTRS_POSSIBLE = #ifdef CONFIG_IBM_NEW_EMAC_EMAC4 - EMAC_FTR_EMAC4 | EMAC_FTR_HAS_AXON_STACR | + EMAC_FTR_EMAC4 | EMAC_FTR_HAS_NEW_STACR | EMAC_FTR_STACR_OC_INVERT | #endif #ifdef CONFIG_IBM_NEW_EMAC_TAH diff --git a/drivers/net/ibm_newemac/debug.c b/drivers/net/ibm_newemac/debug.c index 170524ee0f19..a2fc660ca5d4 100644 --- a/drivers/net/ibm_newemac/debug.c +++ b/drivers/net/ibm_newemac/debug.c @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, debug print routines. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * diff --git a/drivers/net/ibm_newemac/debug.h b/drivers/net/ibm_newemac/debug.h index 1dd2dcbc157f..b631842ec8d0 100644 --- a/drivers/net/ibm_newemac/debug.h +++ b/drivers/net/ibm_newemac/debug.h @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, debug print routines. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * diff --git a/drivers/net/ibm_newemac/emac.h b/drivers/net/ibm_newemac/emac.h index bef92efeeadc..91cb096ab405 100644 --- a/drivers/net/ibm_newemac/emac.h +++ b/drivers/net/ibm_newemac/emac.h @@ -3,6 +3,11 @@ * * Register definitions for PowerPC 4xx on-chip ethernet contoller * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * diff --git a/drivers/net/ibm_newemac/mal.c b/drivers/net/ibm_newemac/mal.c index 9a88f71db004..6869f08c9dcb 100644 --- a/drivers/net/ibm_newemac/mal.c +++ b/drivers/net/ibm_newemac/mal.c @@ -3,6 +3,11 @@ * * Memory Access Layer (MAL) support * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * diff --git a/drivers/net/ibm_newemac/mal.h b/drivers/net/ibm_newemac/mal.h index 784edb8ea822..eaa7262dc079 100644 --- a/drivers/net/ibm_newemac/mal.h +++ b/drivers/net/ibm_newemac/mal.h @@ -3,6 +3,11 @@ * * Memory Access Layer (MAL) support * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * diff --git a/drivers/net/ibm_newemac/phy.c b/drivers/net/ibm_newemac/phy.c index aa1f0ddf1e3e..37bfeea8788a 100644 --- a/drivers/net/ibm_newemac/phy.c +++ b/drivers/net/ibm_newemac/phy.c @@ -8,6 +8,11 @@ * This file should be shared with other drivers or eventually * merged as the "low level" part of miilib * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * (c) 2003, Benjamin Herrenscmidt (benh@kernel.crashing.org) * (c) 2004-2005, Eugene Surovegin <ebs@ebshome.net> * @@ -306,8 +311,84 @@ static struct mii_phy_def cis8201_phy_def = { .ops = &cis8201_phy_ops }; +static struct mii_phy_def bcm5248_phy_def = { + + .phy_id = 0x0143bc00, + .phy_id_mask = 0x0ffffff0, + .name = "BCM5248 10/100 SMII Ethernet", + .ops = &generic_phy_ops +}; + +static int m88e1111_init(struct mii_phy *phy) +{ + pr_debug("%s: Marvell 88E1111 Ethernet\n", __FUNCTION__); + phy_write(phy, 0x14, 0x0ce3); + phy_write(phy, 0x18, 0x4101); + phy_write(phy, 0x09, 0x0e00); + phy_write(phy, 0x04, 0x01e1); + phy_write(phy, 0x00, 0x9140); + phy_write(phy, 0x00, 0x1140); + + return 0; +} + +static int et1011c_init(struct mii_phy *phy) +{ + u16 reg_short; + + reg_short = (u16)(phy_read(phy, 0x16)); + reg_short &= ~(0x7); + reg_short |= 0x6; /* RGMII Trace Delay*/ + phy_write(phy, 0x16, reg_short); + + reg_short = (u16)(phy_read(phy, 0x17)); + reg_short &= ~(0x40); + phy_write(phy, 0x17, reg_short); + + phy_write(phy, 0x1c, 0x74f0); + return 0; +} + +static struct mii_phy_ops et1011c_phy_ops = { + .init = et1011c_init, + .setup_aneg = genmii_setup_aneg, + .setup_forced = genmii_setup_forced, + .poll_link = genmii_poll_link, + .read_link = genmii_read_link +}; + +static struct mii_phy_def et1011c_phy_def = { + .phy_id = 0x0282f000, + .phy_id_mask = 0x0fffff00, + .name = "ET1011C Gigabit Ethernet", + .ops = &et1011c_phy_ops +}; + + + + + +static struct mii_phy_ops m88e1111_phy_ops = { + .init = m88e1111_init, + .setup_aneg = genmii_setup_aneg, + .setup_forced = genmii_setup_forced, + .poll_link = genmii_poll_link, + .read_link = genmii_read_link +}; + +static struct mii_phy_def m88e1111_phy_def = { + + .phy_id = 0x01410CC0, + .phy_id_mask = 0x0ffffff0, + .name = "Marvell 88E1111 Ethernet", + .ops = &m88e1111_phy_ops, +}; + static struct mii_phy_def *mii_phy_table[] = { + &et1011c_phy_def, &cis8201_phy_def, + &bcm5248_phy_def, + &m88e1111_phy_def, &genmii_phy_def, NULL }; diff --git a/drivers/net/ibm_newemac/phy.h b/drivers/net/ibm_newemac/phy.h index 6feca26afedb..1b65c81f6557 100644 --- a/drivers/net/ibm_newemac/phy.h +++ b/drivers/net/ibm_newemac/phy.h @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, PHY support * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Benjamin Herrenschmidt <benh@kernel.crashing.org> * February 2003 * diff --git a/drivers/net/ibm_newemac/rgmii.c b/drivers/net/ibm_newemac/rgmii.c index de416951a435..9bc1132fa788 100644 --- a/drivers/net/ibm_newemac/rgmii.c +++ b/drivers/net/ibm_newemac/rgmii.c @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, RGMII bridge support. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * @@ -140,7 +145,7 @@ void rgmii_get_mdio(struct of_device *ofdev, int input) RGMII_DBG2(dev, "get_mdio(%d)" NL, input); - if (dev->type != RGMII_AXON) + if (!(dev->flags & EMAC_RGMII_FLAG_HAS_MDIO)) return; mutex_lock(&dev->lock); @@ -161,7 +166,7 @@ void rgmii_put_mdio(struct of_device *ofdev, int input) RGMII_DBG2(dev, "put_mdio(%d)" NL, input); - if (dev->type != RGMII_AXON) + if (!(dev->flags & EMAC_RGMII_FLAG_HAS_MDIO)) return; fer = in_be32(&p->fer); @@ -250,11 +255,13 @@ static int __devinit rgmii_probe(struct of_device *ofdev, goto err_free; } - /* Check for RGMII type */ + /* Check for RGMII flags */ + if (of_get_property(ofdev->node, "has-mdio", NULL)) + dev->flags |= EMAC_RGMII_FLAG_HAS_MDIO; + + /* CAB lacks the right properties, fix this up */ if (of_device_is_compatible(ofdev->node, "ibm,rgmii-axon")) - dev->type = RGMII_AXON; - else - dev->type = RGMII_STANDARD; + dev->flags |= EMAC_RGMII_FLAG_HAS_MDIO; DBG2(dev, " Boot FER = 0x%08x, SSR = 0x%08x\n", in_be32(&dev->base->fer), in_be32(&dev->base->ssr)); @@ -263,9 +270,9 @@ static int __devinit rgmii_probe(struct of_device *ofdev, out_be32(&dev->base->fer, 0); printk(KERN_INFO - "RGMII %s %s initialized\n", - dev->type == RGMII_STANDARD ? "standard" : "axon", - ofdev->node->full_name); + "RGMII %s initialized with%s MDIO support\n", + ofdev->node->full_name, + (dev->flags & EMAC_RGMII_FLAG_HAS_MDIO) ? "" : "out"); wmb(); dev_set_drvdata(&ofdev->dev, dev); diff --git a/drivers/net/ibm_newemac/rgmii.h b/drivers/net/ibm_newemac/rgmii.h index 57806833121e..c4a4b358a270 100644 --- a/drivers/net/ibm_newemac/rgmii.h +++ b/drivers/net/ibm_newemac/rgmii.h @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, RGMII bridge support. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Based on ocp_zmii.h/ibm_emac_zmii.h * Armin Kuster akuster@mvista.com * @@ -35,8 +40,9 @@ struct rgmii_regs { struct rgmii_instance { struct rgmii_regs __iomem *base; - /* Type of RGMII bridge */ - int type; + /* RGMII bridge flags */ + int flags; +#define EMAC_RGMII_FLAG_HAS_MDIO 0x00000001 /* Only one EMAC whacks us at a time */ struct mutex lock; diff --git a/drivers/net/ibm_newemac/tah.c b/drivers/net/ibm_newemac/tah.c index f161fb100e8e..96417adec326 100644 --- a/drivers/net/ibm_newemac/tah.c +++ b/drivers/net/ibm_newemac/tah.c @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, TAH support. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright 2004 MontaVista Software, Inc. * Matt Porter <mporter@kernel.crashing.org> * @@ -116,13 +121,14 @@ static int __devinit tah_probe(struct of_device *ofdev, goto err_free; } + dev_set_drvdata(&ofdev->dev, dev); + /* Initialize TAH and enable IPv4 checksum verification, no TSO yet */ tah_reset(ofdev); printk(KERN_INFO "TAH %s initialized\n", ofdev->node->full_name); wmb(); - dev_set_drvdata(&ofdev->dev, dev); return 0; diff --git a/drivers/net/ibm_newemac/tah.h b/drivers/net/ibm_newemac/tah.h index bc41853b6e26..a068b5658dad 100644 --- a/drivers/net/ibm_newemac/tah.h +++ b/drivers/net/ibm_newemac/tah.h @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, TAH support. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright 2004 MontaVista Software, Inc. * Matt Porter <mporter@kernel.crashing.org> * diff --git a/drivers/net/ibm_newemac/zmii.c b/drivers/net/ibm_newemac/zmii.c index 2219ec2740e0..2ea472aeab06 100644 --- a/drivers/net/ibm_newemac/zmii.c +++ b/drivers/net/ibm_newemac/zmii.c @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, ZMII bridge support. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * @@ -83,12 +88,14 @@ int __devinit zmii_attach(struct of_device *ofdev, int input, int *mode) ZMII_DBG(dev, "init(%d, %d)" NL, input, *mode); - if (!zmii_valid_mode(*mode)) + if (!zmii_valid_mode(*mode)) { /* Probably an EMAC connected to RGMII, * but it still may need ZMII for MDIO so * we don't fail here. */ + dev->users++; return 0; + } mutex_lock(&dev->lock); diff --git a/drivers/net/ibm_newemac/zmii.h b/drivers/net/ibm_newemac/zmii.h index 82a9968b1f74..6c9beba0c4b6 100644 --- a/drivers/net/ibm_newemac/zmii.h +++ b/drivers/net/ibm_newemac/zmii.h @@ -3,6 +3,11 @@ * * Driver for PowerPC 4xx on-chip ethernet controller, ZMII bridge support. * + * Copyright 2007 Benjamin Herrenschmidt, IBM Corp. + * <benh@kernel.crashing.org> + * + * Based on the arch/ppc version of the driver: + * * Copyright (c) 2004, 2005 Zultys Technologies. * Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net> * diff --git a/drivers/net/lib82596.c b/drivers/net/lib82596.c index 9a855e512147..b59f442bbf36 100644 --- a/drivers/net/lib82596.c +++ b/drivers/net/lib82596.c @@ -176,8 +176,8 @@ struct i596_reg { struct i596_tbd { unsigned short size; unsigned short pad; - dma_addr_t next; - dma_addr_t data; + u32 next; + u32 data; u32 cache_pad[5]; /* Total 32 bytes... */ }; @@ -195,12 +195,12 @@ struct i596_cmd { struct i596_cmd *v_next; /* Address from CPUs viewpoint */ unsigned short status; unsigned short command; - dma_addr_t b_next; /* Address from i596 viewpoint */ + u32 b_next; /* Address from i596 viewpoint */ }; struct tx_cmd { struct i596_cmd cmd; - dma_addr_t tbd; + u32 tbd; unsigned short size; unsigned short pad; struct sk_buff *skb; /* So we can free it after tx */ @@ -237,8 +237,8 @@ struct cf_cmd { struct i596_rfd { unsigned short stat; unsigned short cmd; - dma_addr_t b_next; /* Address from i596 viewpoint */ - dma_addr_t rbd; + u32 b_next; /* Address from i596 viewpoint */ + u32 rbd; unsigned short count; unsigned short size; struct i596_rfd *v_next; /* Address from CPUs viewpoint */ @@ -249,18 +249,18 @@ struct i596_rfd { }; struct i596_rbd { - /* hardware data */ - unsigned short count; - unsigned short zero1; - dma_addr_t b_next; - dma_addr_t b_data; /* Address from i596 viewpoint */ - unsigned short size; - unsigned short zero2; - /* driver data */ - struct sk_buff *skb; - struct i596_rbd *v_next; - dma_addr_t b_addr; /* This rbd addr from i596 view */ - unsigned char *v_data; /* Address from CPUs viewpoint */ + /* hardware data */ + unsigned short count; + unsigned short zero1; + u32 b_next; + u32 b_data; /* Address from i596 viewpoint */ + unsigned short size; + unsigned short zero2; + /* driver data */ + struct sk_buff *skb; + struct i596_rbd *v_next; + u32 b_addr; /* This rbd addr from i596 view */ + unsigned char *v_data; /* Address from CPUs viewpoint */ /* Total 32 bytes... */ #ifdef __LP64__ u32 cache_pad[4]; @@ -275,8 +275,8 @@ struct i596_rbd { struct i596_scb { unsigned short status; unsigned short command; - dma_addr_t cmd; - dma_addr_t rfd; + u32 cmd; + u32 rfd; u32 crc_err; u32 align_err; u32 resource_err; @@ -288,14 +288,14 @@ struct i596_scb { }; struct i596_iscp { - u32 stat; - dma_addr_t scb; + u32 stat; + u32 scb; }; struct i596_scp { - u32 sysbus; - u32 pad; - dma_addr_t iscp; + u32 sysbus; + u32 pad; + u32 iscp; }; struct i596_dma { diff --git a/drivers/net/myri10ge/myri10ge.c b/drivers/net/myri10ge/myri10ge.c index 0f306ddb5630..8def8657251f 100644 --- a/drivers/net/myri10ge/myri10ge.c +++ b/drivers/net/myri10ge/myri10ge.c @@ -1979,6 +1979,7 @@ static int myri10ge_open(struct net_device *dev) lro_mgr->lro_arr = mgp->rx_done.lro_desc; lro_mgr->get_frag_header = myri10ge_get_frag_header; lro_mgr->max_aggr = myri10ge_lro_max_pkts; + lro_mgr->frag_align_pad = 2; if (lro_mgr->max_aggr > MAX_SKB_FRAGS) lro_mgr->max_aggr = MAX_SKB_FRAGS; diff --git a/drivers/net/niu.c b/drivers/net/niu.c index 112ab079ce7d..abfc61c3a38c 100644 --- a/drivers/net/niu.c +++ b/drivers/net/niu.c @@ -1045,6 +1045,7 @@ static int niu_serdes_init(struct niu *np) } static void niu_init_xif(struct niu *); +static void niu_handle_led(struct niu *, int status); static int niu_link_status_common(struct niu *np, int link_up) { @@ -1066,11 +1067,15 @@ static int niu_link_status_common(struct niu *np, int link_up) spin_lock_irqsave(&np->lock, flags); niu_init_xif(np); + niu_handle_led(np, 1); spin_unlock_irqrestore(&np->lock, flags); netif_carrier_on(dev); } else if (netif_carrier_ok(dev) && !link_up) { niuwarn(LINK, "%s: Link is down\n", dev->name); + spin_lock_irqsave(&np->lock, flags); + niu_handle_led(np, 0); + spin_unlock_irqrestore(&np->lock, flags); netif_carrier_off(dev); } @@ -3915,16 +3920,14 @@ static int niu_init_ipp(struct niu *np) return 0; } -static void niu_init_xif_xmac(struct niu *np) +static void niu_handle_led(struct niu *np, int status) { - struct niu_link_config *lp = &np->link_config; u64 val; - val = nr64_mac(XMAC_CONFIG); if ((np->flags & NIU_FLAGS_10G) != 0 && (np->flags & NIU_FLAGS_FIBER) != 0) { - if (netif_carrier_ok(np->dev)) { + if (status) { val |= XMAC_CONFIG_LED_POLARITY; val &= ~XMAC_CONFIG_FORCE_LED_ON; } else { @@ -3933,6 +3936,15 @@ static void niu_init_xif_xmac(struct niu *np) } } + nw64_mac(XMAC_CONFIG, val); +} + +static void niu_init_xif_xmac(struct niu *np) +{ + struct niu_link_config *lp = &np->link_config; + u64 val; + + val = nr64_mac(XMAC_CONFIG); val &= ~XMAC_CONFIG_SEL_POR_CLK_SRC; val |= XMAC_CONFIG_TX_OUTPUT_EN; @@ -4776,6 +4788,8 @@ static int niu_close(struct net_device *dev) niu_free_channels(np); + niu_handle_led(np, 0); + return 0; } diff --git a/drivers/net/pasemi_mac.c b/drivers/net/pasemi_mac.c index 09b4fde8d924..816a59e801b2 100644 --- a/drivers/net/pasemi_mac.c +++ b/drivers/net/pasemi_mac.c @@ -586,7 +586,7 @@ static int pasemi_mac_clean_rx(struct pasemi_mac *mac, int limit) /* CRC error flagged */ mac->netdev->stats.rx_errors++; mac->netdev->stats.rx_crc_errors++; - dev_kfree_skb_irq(skb); + /* No need to free skb, it'll be reused */ goto next; } @@ -1362,7 +1362,7 @@ pasemi_mac_probe(struct pci_dev *pdev, const struct pci_device_id *ent) netif_napi_add(dev, &mac->napi, pasemi_mac_poll, 64); - dev->features = NETIF_F_HW_CSUM | NETIF_F_LLTX | NETIF_F_SG; + dev->features = NETIF_F_IP_CSUM | NETIF_F_LLTX | NETIF_F_SG; /* These should come out of the device tree eventually */ mac->dma_txch = index; diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c index 035fd41fb61f..f0574073a2a3 100644 --- a/drivers/net/phy/marvell.c +++ b/drivers/net/phy/marvell.c @@ -143,21 +143,29 @@ static int m88e1111_config_init(struct phy_device *phydev) int err; if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) || - (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)) { + (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) || + (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) || + (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID)) { int temp; - if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { - temp = phy_read(phydev, MII_M1111_PHY_EXT_CR); - if (temp < 0) - return temp; + temp = phy_read(phydev, MII_M1111_PHY_EXT_CR); + if (temp < 0) + return temp; + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) { temp |= (MII_M1111_RX_DELAY | MII_M1111_TX_DELAY); - - err = phy_write(phydev, MII_M1111_PHY_EXT_CR, temp); - if (err < 0) - return err; + } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) { + temp &= ~MII_M1111_TX_DELAY; + temp |= MII_M1111_RX_DELAY; + } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) { + temp &= ~MII_M1111_RX_DELAY; + temp |= MII_M1111_TX_DELAY; } + err = phy_write(phydev, MII_M1111_PHY_EXT_CR, temp); + if (err < 0) + return err; + temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); if (temp < 0) return temp; diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index fc2f0e695a13..c30196d0ad16 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -91,9 +91,12 @@ int mdiobus_register(struct mii_bus *bus) err = device_register(&phydev->dev); - if (err) + if (err) { printk(KERN_ERR "phy %d failed to register\n", i); + phy_device_free(phydev); + phydev = NULL; + } } bus->phy_map[i] = phydev; @@ -110,10 +113,8 @@ void mdiobus_unregister(struct mii_bus *bus) int i; for (i = 0; i < PHY_MAX_ADDR; i++) { - if (bus->phy_map[i]) { + if (bus->phy_map[i]) device_unregister(&bus->phy_map[i]->dev); - kfree(bus->phy_map[i]); - } } } EXPORT_SYMBOL(mdiobus_unregister); diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index 9bc11773705b..7c9e6e349503 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -406,6 +406,9 @@ int phy_mii_ioctl(struct phy_device *phydev, && phydev->drv->config_init) phydev->drv->config_init(phydev); break; + + default: + return -ENOTTY; } return 0; diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index f6e484812a98..5b9e1751e1b4 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -44,6 +44,16 @@ static struct phy_driver genphy_driver; extern int mdio_bus_init(void); extern void mdio_bus_exit(void); +void phy_device_free(struct phy_device *phydev) +{ + kfree(phydev); +} + +static void phy_device_release(struct device *dev) +{ + phy_device_free(to_phy_device(dev)); +} + struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id) { struct phy_device *dev; @@ -54,6 +64,8 @@ struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id) if (NULL == dev) return (struct phy_device*) PTR_ERR((void*)-ENOMEM); + dev->dev.release = phy_device_release; + dev->speed = 0; dev->duplex = -1; dev->pause = dev->asym_pause = 0; diff --git a/drivers/net/s2io-regs.h b/drivers/net/s2io-regs.h index 01f08d726ace..f25264f2638e 100644 --- a/drivers/net/s2io-regs.h +++ b/drivers/net/s2io-regs.h @@ -66,6 +66,7 @@ struct XENA_dev_config { #define ADAPTER_STATUS_RC_PRC_QUIESCENT vBIT(0xFF,16,8) #define ADAPTER_STATUS_MC_DRAM_READY s2BIT(24) #define ADAPTER_STATUS_MC_QUEUES_READY s2BIT(25) +#define ADAPTER_STATUS_RIC_RUNNING s2BIT(26) #define ADAPTER_STATUS_M_PLL_LOCK s2BIT(30) #define ADAPTER_STATUS_P_PLL_LOCK s2BIT(31) diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 632666706247..121cb100f93a 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -84,7 +84,7 @@ #include "s2io.h" #include "s2io-regs.h" -#define DRV_VERSION "2.0.26.6" +#define DRV_VERSION "2.0.26.10" /* S2io Driver name & version. */ static char s2io_driver_name[] = "Neterion"; @@ -1081,7 +1081,7 @@ static int init_nic(struct s2io_nic *nic) /* to set the swapper controle on the card */ if(s2io_set_swapper(nic)) { DBG_PRINT(ERR_DBG,"ERROR: Setting Swapper failed\n"); - return -1; + return -EIO; } /* @@ -1100,6 +1100,20 @@ static int init_nic(struct s2io_nic *nic) msleep(500); val64 = readq(&bar0->sw_reset); + /* Ensure that it's safe to access registers by checking + * RIC_RUNNING bit is reset. Check is valid only for XframeII. + */ + if (nic->device_type == XFRAME_II_DEVICE) { + for (i = 0; i < 50; i++) { + val64 = readq(&bar0->adapter_status); + if (!(val64 & ADAPTER_STATUS_RIC_RUNNING)) + break; + msleep(10); + } + if (i == 50) + return -ENODEV; + } + /* Enable Receiving broadcasts */ add = &bar0->mac_cfg; val64 = readq(&bar0->mac_cfg); @@ -1503,7 +1517,7 @@ static int init_nic(struct s2io_nic *nic) DBG_PRINT(ERR_DBG, "%s: failed rts ds steering", dev->name); DBG_PRINT(ERR_DBG, "set on codepoint %d\n", i); - return FAILURE; + return -ENODEV; } } @@ -1570,7 +1584,7 @@ static int init_nic(struct s2io_nic *nic) if (time > 10) { DBG_PRINT(ERR_DBG, "%s: TTI init Failed\n", dev->name); - return -1; + return -ENODEV; } msleep(50); time++; @@ -1623,7 +1637,7 @@ static int init_nic(struct s2io_nic *nic) if (time > 10) { DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n", dev->name); - return -1; + return -ENODEV; } time++; msleep(50); @@ -3914,6 +3928,12 @@ static int s2io_close(struct net_device *dev) { struct s2io_nic *sp = dev->priv; + /* Return if the device is already closed * + * Can happen when s2io_card_up failed in change_mtu * + */ + if (!is_s2io_card_up(sp)) + return 0; + netif_stop_queue(dev); napi_disable(&sp->napi); /* Reset card, kill tasklet and free Tx and Rx buffers. */ @@ -6355,6 +6375,7 @@ static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) static int s2io_change_mtu(struct net_device *dev, int new_mtu) { struct s2io_nic *sp = dev->priv; + int ret = 0; if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) { DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n", @@ -6366,9 +6387,11 @@ static int s2io_change_mtu(struct net_device *dev, int new_mtu) if (netif_running(dev)) { s2io_card_down(sp); netif_stop_queue(dev); - if (s2io_card_up(sp)) { + ret = s2io_card_up(sp); + if (ret) { DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n", __FUNCTION__); + return ret; } if (netif_queue_stopped(dev)) netif_wake_queue(dev); @@ -6379,7 +6402,7 @@ static int s2io_change_mtu(struct net_device *dev, int new_mtu) writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len); } - return 0; + return ret; } /** @@ -6777,6 +6800,9 @@ static void do_s2io_card_down(struct s2io_nic * sp, int do_io) unsigned long flags; register u64 val64 = 0; + if (!is_s2io_card_up(sp)) + return; + del_timer_sync(&sp->alarm_timer); /* If s2io_set_link task is executing, wait till it completes. */ while (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(sp->state))) { @@ -6850,11 +6876,13 @@ static int s2io_card_up(struct s2io_nic * sp) u16 interruptible; /* Initialize the H/W I/O registers */ - if (init_nic(sp) != 0) { + ret = init_nic(sp); + if (ret != 0) { DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n", dev->name); - s2io_reset(sp); - return -ENODEV; + if (ret != -EIO) + s2io_reset(sp); + return ret; } /* diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 6d62250fba07..186eb8ebfda6 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -44,7 +44,7 @@ #include "skge.h" #define DRV_NAME "skge" -#define DRV_VERSION "1.12" +#define DRV_VERSION "1.13" #define PFX DRV_NAME " " #define DEFAULT_TX_RING_SIZE 128 @@ -1095,16 +1095,9 @@ static void xm_link_down(struct skge_hw *hw, int port) { struct net_device *dev = hw->dev[port]; struct skge_port *skge = netdev_priv(dev); - u16 cmd = xm_read16(hw, port, XM_MMU_CMD); xm_write16(hw, port, XM_IMSK, XM_IMSK_DISABLE); - cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX); - xm_write16(hw, port, XM_MMU_CMD, cmd); - - /* dummy read to ensure writing */ - xm_read16(hw, port, XM_MMU_CMD); - if (netif_carrier_ok(dev)) skge_link_down(skge); } @@ -1194,6 +1187,7 @@ static void genesis_init(struct skge_hw *hw) static void genesis_reset(struct skge_hw *hw, int port) { const u8 zero[8] = { 0 }; + u32 reg; skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0); @@ -1209,6 +1203,11 @@ static void genesis_reset(struct skge_hw *hw, int port) xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff); xm_outhash(hw, port, XM_HSM, zero); + + /* Flush TX and RX fifo */ + reg = xm_read32(hw, port, XM_MODE); + xm_write32(hw, port, XM_MODE, reg | XM_MD_FTF); + xm_write32(hw, port, XM_MODE, reg | XM_MD_FRF); } @@ -1634,15 +1633,14 @@ static void genesis_mac_init(struct skge_hw *hw, int port) } xm_write16(hw, port, XM_RX_CMD, r); - /* We want short frames padded to 60 bytes. */ xm_write16(hw, port, XM_TX_CMD, XM_TX_AUTO_PAD); - /* - * Bump up the transmit threshold. This helps hold off transmit - * underruns when we're blasting traffic from both ports at once. - */ - xm_write16(hw, port, XM_TX_THR, 512); + /* Increase threshold for jumbo frames on dual port */ + if (hw->ports > 1 && jumbo) + xm_write16(hw, port, XM_TX_THR, 1020); + else + xm_write16(hw, port, XM_TX_THR, 512); /* * Enable the reception of all error frames. This is is @@ -1713,7 +1711,13 @@ static void genesis_stop(struct skge_port *skge) { struct skge_hw *hw = skge->hw; int port = skge->port; - u32 reg; + unsigned retries = 1000; + u16 cmd; + + /* Disable Tx and Rx */ + cmd = xm_read16(hw, port, XM_MMU_CMD); + cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX); + xm_write16(hw, port, XM_MMU_CMD, cmd); genesis_reset(hw, port); @@ -1721,20 +1725,17 @@ static void genesis_stop(struct skge_port *skge) skge_write16(hw, B3_PA_CTRL, port == 0 ? PA_CLR_TO_TX1 : PA_CLR_TO_TX2); - /* - * If the transfer sticks at the MAC the STOP command will not - * terminate if we don't flush the XMAC's transmit FIFO ! - */ - xm_write32(hw, port, XM_MODE, - xm_read32(hw, port, XM_MODE)|XM_MD_FTF); - - /* Reset the MAC */ - skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST); + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST); + do { + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST); + if (!(skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST)) + break; + } while (--retries > 0); /* For external PHYs there must be special handling */ if (hw->phy_type != SK_PHY_XMAC) { - reg = skge_read32(hw, B2_GP_IO); + u32 reg = skge_read32(hw, B2_GP_IO); if (port == 0) { reg |= GP_DIR_0; reg &= ~GP_IO_0; @@ -1801,11 +1802,6 @@ static void genesis_mac_intr(struct skge_hw *hw, int port) xm_write32(hw, port, XM_MODE, XM_MD_FTF); ++dev->stats.tx_fifo_errors; } - - if (status & XM_IS_RXF_OV) { - xm_write32(hw, port, XM_MODE, XM_MD_FRF); - ++dev->stats.rx_fifo_errors; - } } static void genesis_link_up(struct skge_port *skge) @@ -1862,9 +1858,9 @@ static void genesis_link_up(struct skge_port *skge) xm_write32(hw, port, XM_MODE, mode); - /* Turn on detection of Tx underrun, Rx overrun */ + /* Turn on detection of Tx underrun */ msk = xm_read16(hw, port, XM_IMSK); - msk &= ~(XM_IS_RXF_OV | XM_IS_TXF_UR); + msk &= ~XM_IS_TXF_UR; xm_write16(hw, port, XM_IMSK, msk); xm_read16(hw, port, XM_ISRC); @@ -2194,9 +2190,12 @@ static void yukon_mac_init(struct skge_hw *hw, int port) TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) | TX_IPG_JAM_DATA(TX_IPG_JAM_DEF)); - /* serial mode register */ - reg = GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF); - if (hw->dev[port]->mtu > 1500) + /* configure the Serial Mode Register */ + reg = DATA_BLIND_VAL(DATA_BLIND_DEF) + | GM_SMOD_VLAN_ENA + | IPG_DATA_VAL(IPG_DATA_DEF); + + if (hw->dev[port]->mtu > ETH_DATA_LEN) reg |= GM_SMOD_JUMBO_ENA; gma_write16(hw, port, GM_SERIAL_MODE, reg); @@ -2619,8 +2618,8 @@ static int skge_up(struct net_device *dev) yukon_mac_init(hw, port); spin_unlock_bh(&hw->phy_lock); - /* Configure RAMbuffers */ - chunk = hw->ram_size / ((hw->ports + 1)*2); + /* Configure RAMbuffers - equally between ports and tx/rx */ + chunk = (hw->ram_size - hw->ram_offset) / (hw->ports * 2); ram_addr = hw->ram_offset + 2 * chunk * port; skge_ramset(hw, rxqaddr[port], ram_addr, chunk); @@ -2897,11 +2896,7 @@ static void skge_tx_timeout(struct net_device *dev) static int skge_change_mtu(struct net_device *dev, int new_mtu) { - struct skge_port *skge = netdev_priv(dev); - struct skge_hw *hw = skge->hw; - int port = skge->port; int err; - u16 ctl, reg; if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU) return -EINVAL; @@ -2911,40 +2906,13 @@ static int skge_change_mtu(struct net_device *dev, int new_mtu) return 0; } - skge_write32(hw, B0_IMSK, 0); - dev->trans_start = jiffies; /* prevent tx timeout */ - netif_stop_queue(dev); - napi_disable(&skge->napi); - - ctl = gma_read16(hw, port, GM_GP_CTRL); - gma_write16(hw, port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA); - - skge_rx_clean(skge); - skge_rx_stop(hw, port); + skge_down(dev); dev->mtu = new_mtu; - reg = GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF); - if (new_mtu > 1500) - reg |= GM_SMOD_JUMBO_ENA; - gma_write16(hw, port, GM_SERIAL_MODE, reg); - - skge_write8(hw, RB_ADDR(rxqaddr[port], RB_CTRL), RB_ENA_OP_MD); - - err = skge_rx_fill(dev); - wmb(); - if (!err) - skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_START | CSR_IRQ_CL_F); - skge_write32(hw, B0_IMSK, hw->intr_mask); - + err = skge_up(dev); if (err) dev_close(dev); - else { - gma_write16(hw, port, GM_GP_CTRL, ctl); - - napi_enable(&skge->napi); - netif_wake_queue(dev); - } return err; } diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index a2070db725c9..6197afb3ed83 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -31,7 +31,6 @@ #include <linux/etherdevice.h> #include <linux/ethtool.h> #include <linux/pci.h> -#include <linux/aer.h> #include <linux/ip.h> #include <net/ip.h> #include <linux/tcp.h> @@ -240,22 +239,21 @@ static void sky2_power_on(struct sky2_hw *hw) sky2_write8(hw, B2_Y2_CLK_GATE, 0); if (hw->flags & SKY2_HW_ADV_POWER_CTL) { - struct pci_dev *pdev = hw->pdev; u32 reg; - pci_write_config_dword(pdev, PCI_DEV_REG3, 0); + sky2_pci_write32(hw, PCI_DEV_REG3, 0); - pci_read_config_dword(pdev, PCI_DEV_REG4, ®); + reg = sky2_pci_read32(hw, PCI_DEV_REG4); /* set all bits to 0 except bits 15..12 and 8 */ reg &= P_ASPM_CONTROL_MSK; - pci_write_config_dword(pdev, PCI_DEV_REG4, reg); + sky2_pci_write32(hw, PCI_DEV_REG4, reg); - pci_read_config_dword(pdev, PCI_DEV_REG5, ®); + reg = sky2_pci_read32(hw, PCI_DEV_REG5); /* set all bits to 0 except bits 28 & 27 */ reg &= P_CTL_TIM_VMAIN_AV_MSK; - pci_write_config_dword(pdev, PCI_DEV_REG5, reg); + sky2_pci_write32(hw, PCI_DEV_REG5, reg); - pci_write_config_dword(pdev, PCI_CFG_REG_1, 0); + sky2_pci_write32(hw, PCI_CFG_REG_1, 0); /* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */ reg = sky2_read32(hw, B2_GP_IO); @@ -619,12 +617,11 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) static void sky2_phy_power(struct sky2_hw *hw, unsigned port, int onoff) { - struct pci_dev *pdev = hw->pdev; u32 reg1; static const u32 phy_power[] = { PCI_Y2_PHY1_POWD, PCI_Y2_PHY2_POWD }; static const u32 coma_mode[] = { PCI_Y2_PHY1_COMA, PCI_Y2_PHY2_COMA }; - pci_read_config_dword(pdev, PCI_DEV_REG1, ®1); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); /* Turn on/off phy power saving */ if (onoff) reg1 &= ~phy_power[port]; @@ -634,8 +631,8 @@ static void sky2_phy_power(struct sky2_hw *hw, unsigned port, int onoff) if (onoff && hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) reg1 |= coma_mode[port]; - pci_write_config_dword(pdev, PCI_DEV_REG1, reg1); - pci_read_config_dword(pdev, PCI_DEV_REG1, ®1); + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); udelay(100); } @@ -704,9 +701,9 @@ static void sky2_wol_init(struct sky2_port *sky2) sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl); /* Turn on legacy PCI-Express PME mode */ - pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®1); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); reg1 |= PCI_Y2_PME_LEGACY; - pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg1); + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); /* block receiver */ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); @@ -848,6 +845,13 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) sky2_set_tx_stfwd(hw, port); } + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + /* disable dynamic watermark */ + reg = sky2_read16(hw, SK_REG(port, TX_GMF_EA)); + reg &= ~TX_DYN_WM_ENA; + sky2_write16(hw, SK_REG(port, TX_GMF_EA), reg); + } } /* Assign Ram Buffer allocation to queue */ @@ -1320,15 +1324,12 @@ static int sky2_up(struct net_device *dev) */ if (otherdev && netif_running(otherdev) && (cap = pci_find_capability(hw->pdev, PCI_CAP_ID_PCIX))) { - struct sky2_port *osky2 = netdev_priv(otherdev); u16 cmd; - pci_read_config_word(hw->pdev, cap + PCI_X_CMD, &cmd); + cmd = sky2_pci_read16(hw, cap + PCI_X_CMD); cmd &= ~PCI_X_CMD_MAX_SPLIT; - pci_write_config_word(hw->pdev, cap + PCI_X_CMD, cmd); + sky2_pci_write16(hw, cap + PCI_X_CMD, cmd); - sky2->rx_csum = 0; - osky2->rx_csum = 0; } if (netif_msg_ifup(sky2)) @@ -2426,37 +2427,26 @@ static void sky2_hw_intr(struct sky2_hw *hw) if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) { u16 pci_err; - pci_read_config_word(pdev, PCI_STATUS, &pci_err); + pci_err = sky2_pci_read16(hw, PCI_STATUS); if (net_ratelimit()) dev_err(&pdev->dev, "PCI hardware error (0x%x)\n", pci_err); - pci_write_config_word(pdev, PCI_STATUS, + sky2_pci_write16(hw, PCI_STATUS, pci_err | PCI_STATUS_ERROR_BITS); } if (status & Y2_IS_PCI_EXP) { /* PCI-Express uncorrectable Error occurred */ - int aer = pci_find_aer_capability(hw->pdev); u32 err; - if (aer) { - pci_read_config_dword(pdev, aer + PCI_ERR_UNCOR_STATUS, - &err); - pci_cleanup_aer_uncorrect_error_status(pdev); - } else { - /* Either AER not configured, or not working - * because of bad MMCONFIG, so just do recover - * manually. - */ - err = sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); - sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, - 0xfffffffful); - } - + err = sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); + sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, + 0xfffffffful); if (net_ratelimit()) dev_err(&pdev->dev, "PCI Express error (0x%x)\n", err); + sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); } if (status & Y2_HWE_L1_MASK) @@ -2703,13 +2693,10 @@ static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk) static int __devinit sky2_init(struct sky2_hw *hw) { - int rc; u8 t8; /* Enable all clocks and check for bad PCI access */ - rc = pci_write_config_dword(hw->pdev, PCI_DEV_REG3, 0); - if (rc) - return rc; + sky2_pci_write32(hw, PCI_DEV_REG3, 0); sky2_write8(hw, B0_CTST, CS_RST_CLR); @@ -2806,32 +2793,21 @@ static void sky2_reset(struct sky2_hw *hw) sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); /* clear PCI errors, if any */ - pci_read_config_word(pdev, PCI_STATUS, &status); + status = sky2_pci_read16(hw, PCI_STATUS); status |= PCI_STATUS_ERROR_BITS; - pci_write_config_word(pdev, PCI_STATUS, status); + sky2_pci_write16(hw, PCI_STATUS, status); sky2_write8(hw, B0_CTST, CS_MRST_CLR); cap = pci_find_capability(pdev, PCI_CAP_ID_EXP); if (cap) { - if (pci_find_aer_capability(pdev)) { - /* Check for advanced error reporting */ - pci_cleanup_aer_uncorrect_error_status(pdev); - pci_cleanup_aer_correct_error_status(pdev); - } else { - dev_warn(&pdev->dev, - "PCI Express Advanced Error Reporting" - " not configured or MMCONFIG problem?\n"); - - sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, - 0xfffffffful); - } + sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, + 0xfffffffful); /* If error bit is stuck on ignore it */ if (sky2_read32(hw, B0_HWE_ISRC) & Y2_IS_PCI_EXP) dev_info(&pdev->dev, "ignoring stuck error report bit\n"); - - else if (pci_enable_pcie_error_reporting(pdev)) + else hwe_mask |= Y2_IS_PCI_EXP; } @@ -2930,16 +2906,14 @@ static void sky2_restart(struct work_struct *work) int i, err; rtnl_lock(); - sky2_write32(hw, B0_IMSK, 0); - sky2_read32(hw, B0_IMSK); - napi_disable(&hw->napi); - for (i = 0; i < hw->ports; i++) { dev = hw->dev[i]; if (netif_running(dev)) sky2_down(dev); } + napi_disable(&hw->napi); + sky2_write32(hw, B0_IMSK, 0); sky2_reset(hw); sky2_write32(hw, B0_IMSK, Y2_IS_BASE); napi_enable(&hw->napi); @@ -3672,32 +3646,33 @@ static int sky2_set_tso(struct net_device *dev, u32 data) static int sky2_get_eeprom_len(struct net_device *dev) { struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; u16 reg2; - pci_read_config_word(sky2->hw->pdev, PCI_DEV_REG2, ®2); + reg2 = sky2_pci_read16(hw, PCI_DEV_REG2); return 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8); } -static u32 sky2_vpd_read(struct pci_dev *pdev, int cap, u16 offset) +static u32 sky2_vpd_read(struct sky2_hw *hw, int cap, u16 offset) { u32 val; - pci_write_config_word(pdev, cap + PCI_VPD_ADDR, offset); + sky2_pci_write16(hw, cap + PCI_VPD_ADDR, offset); do { - pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset); + offset = sky2_pci_read16(hw, cap + PCI_VPD_ADDR); } while (!(offset & PCI_VPD_ADDR_F)); - pci_read_config_dword(pdev, cap + PCI_VPD_DATA, &val); + val = sky2_pci_read32(hw, cap + PCI_VPD_DATA); return val; } -static void sky2_vpd_write(struct pci_dev *pdev, int cap, u16 offset, u32 val) +static void sky2_vpd_write(struct sky2_hw *hw, int cap, u16 offset, u32 val) { - pci_write_config_word(pdev, cap + PCI_VPD_DATA, val); - pci_write_config_dword(pdev, cap + PCI_VPD_ADDR, offset | PCI_VPD_ADDR_F); + sky2_pci_write16(hw, cap + PCI_VPD_DATA, val); + sky2_pci_write32(hw, cap + PCI_VPD_ADDR, offset | PCI_VPD_ADDR_F); do { - pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset); + offset = sky2_pci_read16(hw, cap + PCI_VPD_ADDR); } while (offset & PCI_VPD_ADDR_F); } @@ -3715,7 +3690,7 @@ static int sky2_get_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom eeprom->magic = SKY2_EEPROM_MAGIC; while (length > 0) { - u32 val = sky2_vpd_read(sky2->hw->pdev, cap, offset); + u32 val = sky2_vpd_read(sky2->hw, cap, offset); int n = min_t(int, length, sizeof(val)); memcpy(data, &val, n); @@ -3745,10 +3720,10 @@ static int sky2_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom int n = min_t(int, length, sizeof(val)); if (n < sizeof(val)) - val = sky2_vpd_read(sky2->hw->pdev, cap, offset); + val = sky2_vpd_read(sky2->hw, cap, offset); memcpy(&val, data, n); - sky2_vpd_write(sky2->hw->pdev, cap, offset, val); + sky2_vpd_write(sky2->hw, cap, offset, val); length -= n; data += n; @@ -4013,7 +3988,7 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, sky2->duplex = -1; sky2->speed = -1; sky2->advertising = sky2_supported_modes(hw); - sky2->rx_csum = 1; + sky2->rx_csum = (hw->chip_id != CHIP_ID_YUKON_XL); sky2->wol = wol; spin_lock_init(&sky2->phy_lock); @@ -4184,9 +4159,9 @@ static int __devinit sky2_probe(struct pci_dev *pdev, */ { u32 reg; - pci_read_config_dword(pdev,PCI_DEV_REG2, ®); + reg = sky2_pci_read32(hw, PCI_DEV_REG2); reg &= ~PCI_REV_DESC; - pci_write_config_dword(pdev, PCI_DEV_REG2, reg); + sky2_pci_write32(hw, PCI_DEV_REG2, reg); } #endif @@ -4377,7 +4352,7 @@ static int sky2_resume(struct pci_dev *pdev) if (hw->chip_id == CHIP_ID_YUKON_EX || hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_FE_P) - pci_write_config_dword(pdev, PCI_DEV_REG3, 0); + sky2_pci_write32(hw, PCI_DEV_REG3, 0); sky2_reset(hw); sky2_write32(hw, B0_IMSK, Y2_IS_BASE); diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index 69525fd7908d..bc646a47edd2 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -2128,4 +2128,25 @@ static inline void gma_set_addr(struct sky2_hw *hw, unsigned port, unsigned reg, gma_write16(hw, port, reg+4,(u16) addr[2] | ((u16) addr[3] << 8)); gma_write16(hw, port, reg+8,(u16) addr[4] | ((u16) addr[5] << 8)); } + +/* PCI config space access */ +static inline u32 sky2_pci_read32(const struct sky2_hw *hw, unsigned reg) +{ + return sky2_read32(hw, Y2_CFG_SPC + reg); +} + +static inline u16 sky2_pci_read16(const struct sky2_hw *hw, unsigned reg) +{ + return sky2_read16(hw, Y2_CFG_SPC + reg); +} + +static inline void sky2_pci_write32(struct sky2_hw *hw, unsigned reg, u32 val) +{ + sky2_write32(hw, Y2_CFG_SPC + reg, val); +} + +static inline void sky2_pci_write16(struct sky2_hw *hw, unsigned reg, u16 val) +{ + sky2_write16(hw, Y2_CFG_SPC + reg, val); +} #endif diff --git a/drivers/net/smc911x.c b/drivers/net/smc911x.c index dd18af0ce676..76cc1d3adf71 100644 --- a/drivers/net/smc911x.c +++ b/drivers/net/smc911x.c @@ -428,7 +428,6 @@ static inline void smc911x_drop_pkt(struct net_device *dev) */ static inline void smc911x_rcv(struct net_device *dev) { - struct smc911x_local *lp = netdev_priv(dev); unsigned long ioaddr = dev->base_addr; unsigned int pkt_len, status; struct sk_buff *skb; @@ -473,6 +472,7 @@ static inline void smc911x_rcv(struct net_device *dev) skb_put(skb,pkt_len-4); #ifdef SMC_USE_DMA { + struct smc911x_local *lp = netdev_priv(dev); unsigned int fifo; /* Lower the FIFO threshold if possible */ fifo = SMC_GET_FIFO_INT(); @@ -1299,9 +1299,9 @@ smc911x_rx_dma_irq(int dma, void *data) PRINT_PKT(skb->data, skb->len); dev->last_rx = jiffies; skb->protocol = eth_type_trans(skb, dev); - netif_rx(skb); dev->stats.rx_packets++; dev->stats.rx_bytes += skb->len; + netif_rx(skb); spin_lock_irqsave(&lp->lock, flags); pkts = (SMC_GET_RX_FIFO_INF() & RX_FIFO_INF_RXSUSED_) >> 16; @@ -1379,13 +1379,6 @@ static void smc911x_set_multicast_list(struct net_device *dev) unsigned int multicast_table[2]; unsigned int mcr, update_multicast = 0; unsigned long flags; - /* table for flipping the order of 5 bits */ - static const unsigned char invert5[] = - {0x00, 0x10, 0x08, 0x18, 0x04, 0x14, 0x0C, 0x1C, - 0x02, 0x12, 0x0A, 0x1A, 0x06, 0x16, 0x0E, 0x1E, - 0x01, 0x11, 0x09, 0x19, 0x05, 0x15, 0x0D, 0x1D, - 0x03, 0x13, 0x0B, 0x1B, 0x07, 0x17, 0x0F, 0x1F}; - DBG(SMC_DEBUG_FUNC, "%s: --> %s\n", dev->name, __FUNCTION__); @@ -1432,7 +1425,7 @@ static void smc911x_set_multicast_list(struct net_device *dev) cur_addr = dev->mc_list; for (i = 0; i < dev->mc_count; i++, cur_addr = cur_addr->next) { - int position; + u32 position; /* do we have a pointer here? */ if (!cur_addr) @@ -1442,12 +1435,10 @@ static void smc911x_set_multicast_list(struct net_device *dev) if (!(*cur_addr->dmi_addr & 1)) continue; - /* only use the low order bits */ - position = crc32_le(~0, cur_addr->dmi_addr, 6) & 0x3f; + /* upper 6 bits are used as hash index */ + position = ether_crc(ETH_ALEN, cur_addr->dmi_addr)>>26; - /* do some messy swapping to put the bit in the right spot */ - multicast_table[invert5[position&0x1F]&0x1] |= - (1<<invert5[(position>>1)&0x1F]); + multicast_table[position>>5] |= 1 << (position&0x1f); } /* be sure I get rid of flags I might have set */ diff --git a/drivers/net/smc911x.h b/drivers/net/smc911x.h index 16a0edc078fd..d04e4fa35206 100644 --- a/drivers/net/smc911x.h +++ b/drivers/net/smc911x.h @@ -37,7 +37,7 @@ #define SMC_USE_16BIT 0 #define SMC_USE_32BIT 1 #define SMC_IRQ_SENSE IRQF_TRIGGER_FALLING -#elif CONFIG_SH_MAGIC_PANEL_R2 +#elif defined(CONFIG_SH_MAGIC_PANEL_R2) #define SMC_USE_SH_DMA 0 #define SMC_USE_16BIT 0 #define SMC_USE_32BIT 1 diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h index db34e1eb67e9..07b7f7120e37 100644 --- a/drivers/net/smc91x.h +++ b/drivers/net/smc91x.h @@ -55,7 +55,7 @@ #define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) #define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) -#elif defined(CONFIG_BFIN) +#elif defined(CONFIG_BLACKFIN) #define SMC_IRQ_FLAGS IRQF_TRIGGER_HIGH #define RPC_LSA_DEFAULT RPC_LED_100_10 diff --git a/drivers/net/sungem.c b/drivers/net/sungem.c index f6fedcc32de1..68872142530b 100644 --- a/drivers/net/sungem.c +++ b/drivers/net/sungem.c @@ -2281,14 +2281,12 @@ static void gem_reset_task(struct work_struct *work) mutex_lock(&gp->pm_mutex); - napi_disable(&gp->napi); + if (gp->opened) + napi_disable(&gp->napi); spin_lock_irq(&gp->lock); spin_lock(&gp->tx_lock); - if (gp->running == 0) - goto not_running; - if (gp->running) { netif_stop_queue(gp->dev); @@ -2298,13 +2296,14 @@ static void gem_reset_task(struct work_struct *work) gem_set_link_modes(gp); netif_wake_queue(gp->dev); } - not_running: + gp->reset_task_pending = 0; spin_unlock(&gp->tx_lock); spin_unlock_irq(&gp->lock); - napi_enable(&gp->napi); + if (gp->opened) + napi_enable(&gp->napi); mutex_unlock(&gp->pm_mutex); } diff --git a/drivers/net/tulip/dmfe.c b/drivers/net/tulip/dmfe.c index ca90566d5bcd..b4891caeae5a 100644 --- a/drivers/net/tulip/dmfe.c +++ b/drivers/net/tulip/dmfe.c @@ -2118,8 +2118,8 @@ static int dmfe_suspend(struct pci_dev *pci_dev, pm_message_t state) pci_enable_wake(pci_dev, PCI_D3cold, 1); /* Power down device*/ - pci_set_power_state(pci_dev, pci_choose_state (pci_dev,state)); pci_save_state(pci_dev); + pci_set_power_state(pci_dev, pci_choose_state (pci_dev, state)); return 0; } @@ -2129,8 +2129,8 @@ static int dmfe_resume(struct pci_dev *pci_dev) struct net_device *dev = pci_get_drvdata(pci_dev); u32 tmp; - pci_restore_state(pci_dev); pci_set_power_state(pci_dev, PCI_D0); + pci_restore_state(pci_dev); /* Re-initilize DM910X board */ dmfe_init_dm910x(dev); diff --git a/drivers/net/ucc_geth.c b/drivers/net/ucc_geth.c index a3ff270593f1..7f689907ac28 100644 --- a/drivers/net/ucc_geth.c +++ b/drivers/net/ucc_geth.c @@ -1460,6 +1460,8 @@ static int adjust_enet_interface(struct ucc_geth_private *ugeth) if ((ugeth->phy_interface == PHY_INTERFACE_MODE_RMII) || (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII) || (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_ID) || + (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID) || + (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID) || (ugeth->phy_interface == PHY_INTERFACE_MODE_RTBI)) { upsmr |= UPSMR_RPM; switch (ugeth->max_speed) { @@ -1557,6 +1559,8 @@ static void adjust_link(struct net_device *dev) if ((ugeth->phy_interface == PHY_INTERFACE_MODE_RMII) || (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII) || (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_ID) || + (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID) || + (ugeth->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID) || (ugeth->phy_interface == PHY_INTERFACE_MODE_RTBI)) { if (phydev->speed == SPEED_10) upsmr |= UPSMR_R10M; @@ -3795,6 +3799,10 @@ static phy_interface_t to_phy_interface(const char *phy_connection_type) return PHY_INTERFACE_MODE_RGMII; if (strcasecmp(phy_connection_type, "rgmii-id") == 0) return PHY_INTERFACE_MODE_RGMII_ID; + if (strcasecmp(phy_connection_type, "rgmii-txid") == 0) + return PHY_INTERFACE_MODE_RGMII_TXID; + if (strcasecmp(phy_connection_type, "rgmii-rxid") == 0) + return PHY_INTERFACE_MODE_RGMII_RXID; if (strcasecmp(phy_connection_type, "rtbi") == 0) return PHY_INTERFACE_MODE_RTBI; @@ -3889,6 +3897,8 @@ static int ucc_geth_probe(struct of_device* ofdev, const struct of_device_id *ma case PHY_INTERFACE_MODE_GMII: case PHY_INTERFACE_MODE_RGMII: case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_TXID: case PHY_INTERFACE_MODE_TBI: case PHY_INTERFACE_MODE_RTBI: max_speed = SPEED_1000; diff --git a/drivers/net/usb/dm9601.c b/drivers/net/usb/dm9601.c index 2c685734b7a4..1ffdd106f4c4 100644 --- a/drivers/net/usb/dm9601.c +++ b/drivers/net/usb/dm9601.c @@ -94,7 +94,7 @@ static void dm_write_async_callback(struct urb *urb) struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)urb->context; if (urb->status < 0) - printk(KERN_DEBUG "dm_write_async_callback() failed with %d", + printk(KERN_DEBUG "dm_write_async_callback() failed with %d\n", urb->status); kfree(req); diff --git a/drivers/net/via-velocity.c b/drivers/net/via-velocity.c index 450e29d7a9f3..35cd65d6b9ed 100644 --- a/drivers/net/via-velocity.c +++ b/drivers/net/via-velocity.c @@ -1242,6 +1242,9 @@ static int velocity_rx_refill(struct velocity_info *vptr) static int velocity_init_rd_ring(struct velocity_info *vptr) { int ret; + int mtu = vptr->dev->mtu; + + vptr->rx_buf_sz = (mtu <= ETH_DATA_LEN) ? PKT_BUF_SZ : mtu + 32; vptr->rd_info = kcalloc(vptr->options.numrx, sizeof(struct velocity_rd_info), GFP_KERNEL); @@ -1898,8 +1901,6 @@ static int velocity_open(struct net_device *dev) struct velocity_info *vptr = netdev_priv(dev); int ret; - vptr->rx_buf_sz = (dev->mtu <= 1504 ? PKT_BUF_SZ : dev->mtu + 32); - ret = velocity_init_rings(vptr); if (ret < 0) goto out; @@ -1978,12 +1979,6 @@ static int velocity_change_mtu(struct net_device *dev, int new_mtu) velocity_free_rd_ring(vptr); dev->mtu = new_mtu; - if (new_mtu > 8192) - vptr->rx_buf_sz = 9 * 1024; - else if (new_mtu > 4096) - vptr->rx_buf_sz = 8192; - else - vptr->rx_buf_sz = 4 * 1024; ret = velocity_init_rd_ring(vptr); if (ret < 0) diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index 2b17c1dc46f1..b45eecc53c4a 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -1566,7 +1566,7 @@ static void b43_release_firmware(struct b43_wldev *dev) static void b43_print_fw_helptext(struct b43_wl *wl) { b43err(wl, "You must go to " - "http://linuxwireless.org/en/users/Drivers/bcm43xx#devicefirmware " + "http://linuxwireless.org/en/users/Drivers/b43#devicefirmware " "and download the correct firmware (version 4).\n"); } diff --git a/drivers/net/wireless/b43/phy.c b/drivers/net/wireless/b43/phy.c index 3d4ed647c311..7ff091e69f05 100644 --- a/drivers/net/wireless/b43/phy.c +++ b/drivers/net/wireless/b43/phy.c @@ -2214,7 +2214,7 @@ int b43_phy_init_tssi2dbm_table(struct b43_wldev *dev) } dyn_tssi2dbm = kmalloc(64, GFP_KERNEL); if (dyn_tssi2dbm == NULL) { - b43err(dev->wl, "Could not allocate memory" + b43err(dev->wl, "Could not allocate memory " "for tssi2dbm table\n"); return -ENOMEM; } diff --git a/drivers/net/wireless/b43legacy/dma.c b/drivers/net/wireless/b43legacy/dma.c index 8cb3dc4c4745..83161d9af813 100644 --- a/drivers/net/wireless/b43legacy/dma.c +++ b/drivers/net/wireless/b43legacy/dma.c @@ -996,7 +996,7 @@ int b43legacy_dma_init(struct b43legacy_wldev *dev) err = ssb_dma_set_mask(dev->dev, dmamask); if (err) { -#ifdef BCM43XX_PIO +#ifdef CONFIG_B43LEGACY_PIO b43legacywarn(dev->wl, "DMA for this device not supported. " "Falling back to PIO\n"); dev->__using_pio = 1; diff --git a/drivers/net/wireless/b43legacy/main.c b/drivers/net/wireless/b43legacy/main.c index 3bde1e9ab428..32d5e1785bda 100644 --- a/drivers/net/wireless/b43legacy/main.c +++ b/drivers/net/wireless/b43legacy/main.c @@ -1419,7 +1419,7 @@ static void b43legacy_release_firmware(struct b43legacy_wldev *dev) static void b43legacy_print_fw_helptext(struct b43legacy_wl *wl) { b43legacyerr(wl, "You must go to http://linuxwireless.org/en/users/" - "Drivers/bcm43xx#devicefirmware " + "Drivers/b43#devicefirmware " "and download the correct firmware (version 3).\n"); } diff --git a/drivers/net/wireless/b43legacy/phy.c b/drivers/net/wireless/b43legacy/phy.c index 22a4b3d0186d..491e518e4aeb 100644 --- a/drivers/net/wireless/b43legacy/phy.c +++ b/drivers/net/wireless/b43legacy/phy.c @@ -2020,7 +2020,7 @@ int b43legacy_phy_init_tssi2dbm_table(struct b43legacy_wldev *dev) phy->idle_tssi = 62; dyn_tssi2dbm = kmalloc(64, GFP_KERNEL); if (dyn_tssi2dbm == NULL) { - b43legacyerr(dev->wl, "Could not allocate memory" + b43legacyerr(dev->wl, "Could not allocate memory " "for tssi2dbm table\n"); return -ENOMEM; } diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c index b37f1e348700..af3de3343650 100644 --- a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c +++ b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c @@ -2149,7 +2149,7 @@ int bcm43xx_phy_init_tssi2dbm_table(struct bcm43xx_private *bcm) } dyn_tssi2dbm = kmalloc(64, GFP_KERNEL); if (dyn_tssi2dbm == NULL) { - printk(KERN_ERR PFX "Could not allocate memory" + printk(KERN_ERR PFX "Could not allocate memory " "for tssi2dbm table\n"); return -ENOMEM; } diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 465da4f67ce7..4bdf237f6adc 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -2915,6 +2915,10 @@ static void iwl_set_rate(struct iwl_priv *priv) int i; hw = iwl_get_hw_mode(priv, priv->phymode); + if (!hw) { + IWL_ERROR("Failed to set rate: unable to get hw mode\n"); + return; + } priv->active_rate = 0; priv->active_rate_basic = 0; @@ -6936,13 +6940,10 @@ static int iwl_mac_add_interface(struct ieee80211_hw *hw, DECLARE_MAC_BUF(mac); IWL_DEBUG_MAC80211("enter: id %d, type %d\n", conf->if_id, conf->type); - if (conf->mac_addr) - IWL_DEBUG_MAC80211("enter: MAC %s\n", - print_mac(mac, conf->mac_addr)); if (priv->interface_id) { IWL_DEBUG_MAC80211("leave - interface_id != 0\n"); - return 0; + return -EOPNOTSUPP; } spin_lock_irqsave(&priv->lock, flags); @@ -6951,6 +6952,12 @@ static int iwl_mac_add_interface(struct ieee80211_hw *hw, spin_unlock_irqrestore(&priv->lock, flags); mutex_lock(&priv->mutex); + + if (conf->mac_addr) { + IWL_DEBUG_MAC80211("Set: %s\n", print_mac(mac, conf->mac_addr)); + memcpy(priv->mac_addr, conf->mac_addr, ETH_ALEN); + } + iwl_set_mode(priv, conf->type); IWL_DEBUG_MAC80211("leave\n"); @@ -8270,6 +8277,7 @@ static void iwl_cancel_deferred_work(struct iwl_priv *priv) { iwl_hw_cancel_deferred_work(priv); + cancel_delayed_work_sync(&priv->init_alive_start); cancel_delayed_work(&priv->scan_check); cancel_delayed_work(&priv->alive_start); cancel_delayed_work(&priv->post_associate); diff --git a/drivers/net/wireless/iwlwifi/iwl4965-base.c b/drivers/net/wireless/iwlwifi/iwl4965-base.c index 9918780f5e86..8f85564ec6fa 100644 --- a/drivers/net/wireless/iwlwifi/iwl4965-base.c +++ b/drivers/net/wireless/iwlwifi/iwl4965-base.c @@ -3003,6 +3003,10 @@ static void iwl_set_rate(struct iwl_priv *priv) int i; hw = iwl_get_hw_mode(priv, priv->phymode); + if (!hw) { + IWL_ERROR("Failed to set rate: unable to get hw mode\n"); + return; + } priv->active_rate = 0; priv->active_rate_basic = 0; @@ -7326,9 +7330,6 @@ static int iwl_mac_add_interface(struct ieee80211_hw *hw, DECLARE_MAC_BUF(mac); IWL_DEBUG_MAC80211("enter: id %d, type %d\n", conf->if_id, conf->type); - if (conf->mac_addr) - IWL_DEBUG_MAC80211("enter: MAC %s\n", - print_mac(mac, conf->mac_addr)); if (priv->interface_id) { IWL_DEBUG_MAC80211("leave - interface_id != 0\n"); @@ -7341,6 +7342,11 @@ static int iwl_mac_add_interface(struct ieee80211_hw *hw, spin_unlock_irqrestore(&priv->lock, flags); mutex_lock(&priv->mutex); + + if (conf->mac_addr) { + IWL_DEBUG_MAC80211("Set %s\n", print_mac(mac, conf->mac_addr)); + memcpy(priv->mac_addr, conf->mac_addr, ETH_ALEN); + } iwl_set_mode(priv, conf->type); IWL_DEBUG_MAC80211("leave\n"); @@ -8864,6 +8870,7 @@ static void iwl_cancel_deferred_work(struct iwl_priv *priv) { iwl_hw_cancel_deferred_work(priv); + cancel_delayed_work_sync(&priv->init_alive_start); cancel_delayed_work(&priv->scan_check); cancel_delayed_work(&priv->alive_start); cancel_delayed_work(&priv->post_associate); diff --git a/drivers/net/wireless/libertas/if_cs.c b/drivers/net/wireless/libertas/if_cs.c index ec89dabc412c..ba4fc2b3bf0a 100644 --- a/drivers/net/wireless/libertas/if_cs.c +++ b/drivers/net/wireless/libertas/if_cs.c @@ -170,7 +170,8 @@ static int if_cs_poll_while_fw_download(struct if_cs_card *card, uint addr, u8 r #define IF_CS_H_IC_TX_OVER 0x0001 #define IF_CS_H_IC_RX_OVER 0x0002 #define IF_CS_H_IC_DNLD_OVER 0x0004 -#define IF_CS_H_IC_HOST_EVENT 0x0008 +#define IF_CS_H_IC_POWER_DOWN 0x0008 +#define IF_CS_H_IC_HOST_EVENT 0x0010 #define IF_CS_H_IC_MASK 0x001f #define IF_CS_H_INT_MASK 0x00000004 diff --git a/drivers/net/wireless/libertas/main.c b/drivers/net/wireless/libertas/main.c index 5ead08312e1e..1823b48a8ba7 100644 --- a/drivers/net/wireless/libertas/main.c +++ b/drivers/net/wireless/libertas/main.c @@ -1165,8 +1165,6 @@ wlan_private *libertas_add_card(void *card, struct device *dmdev) #ifdef WIRELESS_EXT dev->wireless_handlers = (struct iw_handler_def *)&libertas_handler_def; #endif -#define NETIF_F_DYNALLOC 16 - dev->features |= NETIF_F_DYNALLOC; dev->flags |= IFF_BROADCAST | IFF_MULTICAST; dev->set_multicast_list = libertas_set_multicast_list; @@ -1348,8 +1346,6 @@ int libertas_add_mesh(wlan_private *priv, struct device *dev) #ifdef WIRELESS_EXT mesh_dev->wireless_handlers = (struct iw_handler_def *)&mesh_handler_def; #endif -#define NETIF_F_DYNALLOC 16 - /* Register virtual mesh interface */ ret = register_netdev(mesh_dev); if (ret) { diff --git a/drivers/net/wireless/libertas/wext.c b/drivers/net/wireless/libertas/wext.c index c6f5aa3cb465..395b7882d4d6 100644 --- a/drivers/net/wireless/libertas/wext.c +++ b/drivers/net/wireless/libertas/wext.c @@ -1528,7 +1528,7 @@ static int wlan_set_encodeext(struct net_device *dev, && (ext->key_len != KEY_LEN_WPA_TKIP)) || ((alg == IW_ENCODE_ALG_CCMP) && (ext->key_len != KEY_LEN_WPA_AES))) { - lbs_deb_wext("invalid size %d for key of alg" + lbs_deb_wext("invalid size %d for key of alg " "type %d\n", ext->key_len, alg); diff --git a/drivers/net/wireless/netwave_cs.c b/drivers/net/wireless/netwave_cs.c index 2402cb8dd328..d2fa079fbc4c 100644 --- a/drivers/net/wireless/netwave_cs.c +++ b/drivers/net/wireless/netwave_cs.c @@ -806,7 +806,7 @@ static int netwave_pcmcia_config(struct pcmcia_device *link) { for (i = 0; i < 6; i++) dev->dev_addr[i] = readb(ramBase + NETWAVE_EREG_PA + i); - printk(KERN_INFO "%s: Netwave: port %#3lx, irq %d, mem %lx" + printk(KERN_INFO "%s: Netwave: port %#3lx, irq %d, mem %lx, " "id %c%c, hw_addr %s\n", dev->name, dev->base_addr, dev->irq, (u_long) ramBase, diff --git a/drivers/net/wireless/p54usb.c b/drivers/net/wireless/p54usb.c index 755482a5a938..60d286eb0b8b 100644 --- a/drivers/net/wireless/p54usb.c +++ b/drivers/net/wireless/p54usb.c @@ -308,7 +308,7 @@ static int p54u_read_eeprom(struct ieee80211_hw *dev) buf = kmalloc(0x2020, GFP_KERNEL); if (!buf) { - printk(KERN_ERR "prism54usb: cannot allocate memory for" + printk(KERN_ERR "prism54usb: cannot allocate memory for " "eeprom readback!\n"); return -ENOMEM; } diff --git a/drivers/parisc/lba_pci.c b/drivers/parisc/lba_pci.c index 5eace9e66e14..66ce61048361 100644 --- a/drivers/parisc/lba_pci.c +++ b/drivers/parisc/lba_pci.c @@ -768,9 +768,13 @@ lba_fixup_bus(struct pci_bus *bus) DBG("lba_fixup_bus() WTF? 0x%lx [%lx/%lx] XXX", res->flags, res->start, res->end); } - if ((i != PCI_ROM_RESOURCE) || - (res->flags & IORESOURCE_ROM_ENABLE)) - pci_claim_resource(dev, i); + + /* + ** FIXME: this will result in whinging for devices + ** that share expansion ROMs (think quad tulip), but + ** isn't harmful. + */ + pci_claim_resource(dev, i); } #ifdef FBB_SUPPORT diff --git a/drivers/rtc/interface.c b/drivers/rtc/interface.c index a4f56e95cf96..f1e00ff54ce8 100644 --- a/drivers/rtc/interface.c +++ b/drivers/rtc/interface.c @@ -293,7 +293,7 @@ int rtc_irq_register(struct rtc_device *rtc, struct rtc_task *task) return -EINVAL; /* Cannot register while the char dev is in use */ - if (test_and_set_bit(RTC_DEV_BUSY, &rtc->flags)) + if (test_and_set_bit_lock(RTC_DEV_BUSY, &rtc->flags)) return -EBUSY; spin_lock_irq(&rtc->irq_task_lock); @@ -303,7 +303,7 @@ int rtc_irq_register(struct rtc_device *rtc, struct rtc_task *task) } spin_unlock_irq(&rtc->irq_task_lock); - clear_bit(RTC_DEV_BUSY, &rtc->flags); + clear_bit_unlock(RTC_DEV_BUSY, &rtc->flags); return retval; } diff --git a/drivers/rtc/rtc-dev.c b/drivers/rtc/rtc-dev.c index ae1bf177d625..025c60a17a4a 100644 --- a/drivers/rtc/rtc-dev.c +++ b/drivers/rtc/rtc-dev.c @@ -26,7 +26,7 @@ static int rtc_dev_open(struct inode *inode, struct file *file) struct rtc_device, char_dev); const struct rtc_class_ops *ops = rtc->ops; - if (test_and_set_bit(RTC_DEV_BUSY, &rtc->flags)) + if (test_and_set_bit_lock(RTC_DEV_BUSY, &rtc->flags)) return -EBUSY; file->private_data = rtc; @@ -41,7 +41,7 @@ static int rtc_dev_open(struct inode *inode, struct file *file) } /* something has gone wrong */ - clear_bit(RTC_DEV_BUSY, &rtc->flags); + clear_bit_unlock(RTC_DEV_BUSY, &rtc->flags); return err; } @@ -402,7 +402,7 @@ static int rtc_dev_release(struct inode *inode, struct file *file) if (rtc->ops->release) rtc->ops->release(rtc->dev.parent); - clear_bit(RTC_DEV_BUSY, &rtc->flags); + clear_bit_unlock(RTC_DEV_BUSY, &rtc->flags); return 0; } diff --git a/drivers/rtc/rtc-max6902.c b/drivers/rtc/rtc-max6902.c index 3e183cfee10f..1f956dc5d56e 100644 --- a/drivers/rtc/rtc-max6902.c +++ b/drivers/rtc/rtc-max6902.c @@ -89,13 +89,9 @@ static int max6902_get_reg(struct device *dev, unsigned char address, /* do the i/o */ status = spi_sync(spi, &message); - if (status == 0) - status = message.status; - else - return status; - - *data = chip->rx_buf[1]; + if (status == 0) + *data = chip->rx_buf[1]; return status; } @@ -125,9 +121,7 @@ static int max6902_get_datetime(struct device *dev, struct rtc_time *dt) /* do the i/o */ status = spi_sync(spi, &message); - if (status == 0) - status = message.status; - else + if (status) return status; /* The chip sends data in this order: diff --git a/drivers/s390/block/dcssblk.c b/drivers/s390/block/dcssblk.c index 5e083d1f57e7..15a5789b7734 100644 --- a/drivers/s390/block/dcssblk.c +++ b/drivers/s390/block/dcssblk.c @@ -472,11 +472,11 @@ dcssblk_add_store(struct device *dev, struct device_attribute *attr, const char if (rc) goto unregister_dev; - add_disk(dev_info->gd); - blk_queue_make_request(dev_info->dcssblk_queue, dcssblk_make_request); blk_queue_hardsect_size(dev_info->dcssblk_queue, 4096); + add_disk(dev_info->gd); + switch (dev_info->segment_type) { case SEG_TYPE_SR: case SEG_TYPE_ER: diff --git a/drivers/s390/cio/css.c b/drivers/s390/cio/css.c index 6db31089d2d7..c3df2cd009a4 100644 --- a/drivers/s390/cio/css.c +++ b/drivers/s390/cio/css.c @@ -451,6 +451,7 @@ static int reprobe_subchannel(struct subchannel_id schid, void *data) break; case -ENXIO: case -ENOMEM: + case -EIO: /* These should abort looping */ break; default: diff --git a/drivers/s390/cio/device_id.c b/drivers/s390/cio/device_id.c index 2f6bf462425e..156f3f9786b5 100644 --- a/drivers/s390/cio/device_id.c +++ b/drivers/s390/cio/device_id.c @@ -113,6 +113,7 @@ __ccw_device_sense_id_start(struct ccw_device *cdev) { struct subchannel *sch; struct ccw1 *ccw; + int ret; sch = to_subchannel(cdev->dev.parent); /* Setup sense channel program. */ @@ -124,9 +125,25 @@ __ccw_device_sense_id_start(struct ccw_device *cdev) /* Reset device status. */ memset(&cdev->private->irb, 0, sizeof(struct irb)); - cdev->private->flags.intretry = 0; - return cio_start(sch, ccw, LPM_ANYPATH); + /* Try on every path. */ + ret = -ENODEV; + while (cdev->private->imask != 0) { + if ((sch->opm & cdev->private->imask) != 0 && + cdev->private->iretry > 0) { + cdev->private->iretry--; + /* Reset internal retry indication. */ + cdev->private->flags.intretry = 0; + ret = cio_start (sch, cdev->private->iccws, + cdev->private->imask); + /* ret is 0, -EBUSY, -EACCES or -ENODEV */ + if (ret != -EACCES) + return ret; + } + cdev->private->imask >>= 1; + cdev->private->iretry = 5; + } + return ret; } void @@ -136,7 +153,8 @@ ccw_device_sense_id_start(struct ccw_device *cdev) memset (&cdev->private->senseid, 0, sizeof (struct senseid)); cdev->private->senseid.cu_type = 0xFFFF; - cdev->private->iretry = 3; + cdev->private->imask = 0x80; + cdev->private->iretry = 5; ret = __ccw_device_sense_id_start(cdev); if (ret && ret != -EBUSY) ccw_device_sense_id_done(cdev, ret); @@ -252,13 +270,14 @@ ccw_device_sense_id_irq(struct ccw_device *cdev, enum dev_event dev_event) ccw_device_sense_id_done(cdev, ret); break; case -EACCES: /* channel is not operational. */ + sch->lpm &= ~cdev->private->imask; + cdev->private->imask >>= 1; + cdev->private->iretry = 5; + /* fall through. */ case -EAGAIN: /* try again. */ - cdev->private->iretry--; - if (cdev->private->iretry > 0) { - ret = __ccw_device_sense_id_start(cdev); - if (ret == 0 || ret == -EBUSY) - break; - } + ret = __ccw_device_sense_id_start(cdev); + if (ret == 0 || ret == -EBUSY) + break; /* fall through. */ default: /* Sense ID failed. Try asking VM. */ if (MACHINE_IS_VM) { diff --git a/drivers/s390/net/ctcmain.c b/drivers/s390/net/ctcmain.c index 6bf3ebbe985a..97adc701a819 100644 --- a/drivers/s390/net/ctcmain.c +++ b/drivers/s390/net/ctcmain.c @@ -2782,35 +2782,14 @@ ctc_probe_device(struct ccwgroup_device *cgdev) } /** - * Initialize everything of the net device except the name and the - * channel structs. + * Device setup function called by alloc_netdev(). + * + * @param dev Device to be setup. */ -static struct net_device * -ctc_init_netdevice(struct net_device * dev, int alloc_device, - struct ctc_priv *privptr) +void ctc_init_netdevice(struct net_device * dev) { - if (!privptr) - return NULL; - DBF_TEXT(setup, 3, __FUNCTION__); - if (alloc_device) { - dev = kzalloc(sizeof(struct net_device), GFP_KERNEL); - if (!dev) - return NULL; - } - - dev->priv = privptr; - privptr->fsm = init_fsm("ctcdev", dev_state_names, - dev_event_names, CTC_NR_DEV_STATES, CTC_NR_DEV_EVENTS, - dev_fsm, DEV_FSM_LEN, GFP_KERNEL); - if (privptr->fsm == NULL) { - if (alloc_device) - kfree(dev); - return NULL; - } - fsm_newstate(privptr->fsm, DEV_STATE_STOPPED); - fsm_settimer(privptr->fsm, &privptr->restart_timer); if (dev->mtu == 0) dev->mtu = CTC_BUFSIZE_DEFAULT - LL_HEADER_LENGTH - 2; dev->hard_start_xmit = ctc_tx; @@ -2823,7 +2802,6 @@ ctc_init_netdevice(struct net_device * dev, int alloc_device, dev->type = ARPHRD_SLIP; dev->tx_queue_len = 100; dev->flags = IFF_POINTOPOINT | IFF_NOARP; - return dev; } @@ -2879,14 +2857,22 @@ ctc_new_device(struct ccwgroup_device *cgdev) "ccw_device_set_online (cdev[1]) failed with ret = %d\n", ret); } - dev = ctc_init_netdevice(NULL, 1, privptr); - + dev = alloc_netdev(0, "ctc%d", ctc_init_netdevice); if (!dev) { ctc_pr_warn("ctc_init_netdevice failed\n"); goto out; } + dev->priv = privptr; - strlcpy(dev->name, "ctc%d", IFNAMSIZ); + privptr->fsm = init_fsm("ctcdev", dev_state_names, + dev_event_names, CTC_NR_DEV_STATES, CTC_NR_DEV_EVENTS, + dev_fsm, DEV_FSM_LEN, GFP_KERNEL); + if (privptr->fsm == NULL) { + free_netdev(dev); + goto out; + } + fsm_newstate(privptr->fsm, DEV_STATE_STOPPED); + fsm_settimer(privptr->fsm, &privptr->restart_timer); for (direction = READ; direction <= WRITE; direction++) { privptr->channel[direction] = diff --git a/drivers/s390/scsi/zfcp_erp.c b/drivers/s390/scsi/zfcp_erp.c index 5552b755c08a..07fa824d179f 100644 --- a/drivers/s390/scsi/zfcp_erp.c +++ b/drivers/s390/scsi/zfcp_erp.c @@ -977,7 +977,9 @@ static void zfcp_erp_action_dismiss(struct zfcp_erp_action *erp_action) debug_text_event(adapter->erp_dbf, 2, "a_adis"); debug_event(adapter->erp_dbf, 2, &erp_action->action, sizeof (int)); - zfcp_erp_async_handler_nolock(erp_action, ZFCP_STATUS_ERP_DISMISSED); + erp_action->status |= ZFCP_STATUS_ERP_DISMISSED; + if (zfcp_erp_action_exists(erp_action) == ZFCP_ERP_ACTION_RUNNING) + zfcp_erp_action_ready(erp_action); } int @@ -1063,7 +1065,7 @@ zfcp_erp_thread(void *data) &adapter->status)) { write_lock_irqsave(&adapter->erp_lock, flags); - next = adapter->erp_ready_head.prev; + next = adapter->erp_ready_head.next; write_unlock_irqrestore(&adapter->erp_lock, flags); if (next != &adapter->erp_ready_head) { @@ -1153,15 +1155,13 @@ zfcp_erp_strategy(struct zfcp_erp_action *erp_action) /* * check for dismissed status again to avoid follow-up actions, - * failing of targets and so on for dismissed actions + * failing of targets and so on for dismissed actions, + * we go through down() here because there has been an up() */ - retval = zfcp_erp_strategy_check_action(erp_action, retval); + if (erp_action->status & ZFCP_STATUS_ERP_DISMISSED) + retval = ZFCP_ERP_CONTINUES; switch (retval) { - case ZFCP_ERP_DISMISSED: - /* leave since this action has ridden to its ancestors */ - debug_text_event(adapter->erp_dbf, 6, "a_st_dis2"); - goto unlock; case ZFCP_ERP_NOMEM: /* no memory to continue immediately, let it sleep */ if (!(erp_action->status & ZFCP_STATUS_ERP_LOWMEM)) { @@ -3089,7 +3089,7 @@ zfcp_erp_action_enqueue(int action, ++adapter->erp_total_count; /* finally put it into 'ready' queue and kick erp thread */ - list_add(&erp_action->list, &adapter->erp_ready_head); + list_add_tail(&erp_action->list, &adapter->erp_ready_head); up(&adapter->erp_ready_sem); retval = 0; out: diff --git a/drivers/scsi/aacraid/commsup.c b/drivers/scsi/aacraid/commsup.c index 240a0bb8986f..abce48ccc85b 100644 --- a/drivers/scsi/aacraid/commsup.c +++ b/drivers/scsi/aacraid/commsup.c @@ -1339,10 +1339,10 @@ int aac_check_health(struct aac_dev * aac) aif = (struct aac_aifcmd *)hw_fib->data; aif->command = cpu_to_le32(AifCmdEventNotify); aif->seqnum = cpu_to_le32(0xFFFFFFFF); - aif->data[0] = cpu_to_le32(AifEnExpEvent); - aif->data[1] = cpu_to_le32(AifExeFirmwarePanic); - aif->data[2] = cpu_to_le32(AifHighPriority); - aif->data[3] = cpu_to_le32(BlinkLED); + aif->data[0] = AifEnExpEvent; + aif->data[1] = AifExeFirmwarePanic; + aif->data[2] = AifHighPriority; + aif->data[3] = BlinkLED; /* * Put the FIB onto the diff --git a/drivers/scsi/aacraid/linit.c b/drivers/scsi/aacraid/linit.c index 038980be763d..9dd331bc29b0 100644 --- a/drivers/scsi/aacraid/linit.c +++ b/drivers/scsi/aacraid/linit.c @@ -636,7 +636,7 @@ static int aac_cfg_open(struct inode *inode, struct file *file) static int aac_cfg_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg) { - if (!capable(CAP_SYS_ADMIN)) + if (!capable(CAP_SYS_RAWIO)) return -EPERM; return aac_do_ioctl(file->private_data, cmd, (void __user *)arg); } @@ -691,7 +691,7 @@ static int aac_compat_ioctl(struct scsi_device *sdev, int cmd, void __user *arg) static long aac_compat_cfg_ioctl(struct file *file, unsigned cmd, unsigned long arg) { - if (!capable(CAP_SYS_ADMIN)) + if (!capable(CAP_SYS_RAWIO)) return -EPERM; return aac_compat_do_ioctl((struct aac_dev *)file->private_data, cmd, arg); } @@ -950,7 +950,8 @@ static struct scsi_host_template aac_driver_template = { static void __aac_shutdown(struct aac_dev * aac) { - kthread_stop(aac->thread); + if (aac->aif_thread) + kthread_stop(aac->thread); aac_send_shutdown(aac); aac_adapter_disable_int(aac); free_irq(aac->pdev->irq, aac); diff --git a/drivers/scsi/atari_scsi.c b/drivers/scsi/atari_scsi.c index 6f8403b82ba1..f5732d8f67fe 100644 --- a/drivers/scsi/atari_scsi.c +++ b/drivers/scsi/atari_scsi.c @@ -393,7 +393,7 @@ static irqreturn_t scsi_tt_intr(int irq, void *dummy) #endif /* REAL_DMA */ - NCR5380_intr(0, 0); + NCR5380_intr(irq, dummy); #if 0 /* To be sure the int is not masked */ @@ -458,7 +458,7 @@ static irqreturn_t scsi_falcon_intr(int irq, void *dummy) #endif /* REAL_DMA */ - NCR5380_intr(0, 0); + NCR5380_intr(irq, dummy); return IRQ_HANDLED; } @@ -684,7 +684,7 @@ int atari_scsi_detect(struct scsi_host_template *host) * interrupt after having cleared the pending flag for the DMA * interrupt. */ if (request_irq(IRQ_TT_MFP_SCSI, scsi_tt_intr, IRQ_TYPE_SLOW, - "SCSI NCR5380", scsi_tt_intr)) { + "SCSI NCR5380", instance)) { printk(KERN_ERR "atari_scsi_detect: cannot allocate irq %d, aborting",IRQ_TT_MFP_SCSI); scsi_unregister(atari_scsi_host); atari_stram_free(atari_dma_buffer); @@ -701,7 +701,7 @@ int atari_scsi_detect(struct scsi_host_template *host) IRQ_TYPE_PRIO, "Hades DMA emulator", hades_dma_emulator)) { printk(KERN_ERR "atari_scsi_detect: cannot allocate irq %d, aborting (MACH_IS_HADES)",IRQ_AUTO_2); - free_irq(IRQ_TT_MFP_SCSI, scsi_tt_intr); + free_irq(IRQ_TT_MFP_SCSI, instance); scsi_unregister(atari_scsi_host); atari_stram_free(atari_dma_buffer); atari_dma_buffer = 0; @@ -761,7 +761,7 @@ int atari_scsi_detect(struct scsi_host_template *host) int atari_scsi_release(struct Scsi_Host *sh) { if (IS_A_TT()) - free_irq(IRQ_TT_MFP_SCSI, scsi_tt_intr); + free_irq(IRQ_TT_MFP_SCSI, sh); if (atari_dma_buffer) atari_stram_free(atari_dma_buffer); return 1; diff --git a/drivers/scsi/dtc.c b/drivers/scsi/dtc.c index 2596165096d3..c2677ba29c74 100644 --- a/drivers/scsi/dtc.c +++ b/drivers/scsi/dtc.c @@ -277,7 +277,8 @@ found: /* With interrupts enabled, it will sometimes hang when doing heavy * reads. So better not enable them until I finger it out. */ if (instance->irq != SCSI_IRQ_NONE) - if (request_irq(instance->irq, dtc_intr, IRQF_DISABLED, "dtc", instance)) { + if (request_irq(instance->irq, dtc_intr, IRQF_DISABLED, + "dtc", instance)) { printk(KERN_ERR "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); instance->irq = SCSI_IRQ_NONE; } @@ -459,7 +460,7 @@ static int dtc_release(struct Scsi_Host *shost) NCR5380_local_declare(); NCR5380_setup(shost); if (shost->irq) - free_irq(shost->irq, NULL); + free_irq(shost->irq, shost); NCR5380_exit(shost); if (shost->io_port && shost->n_io_port) release_region(shost->io_port, shost->n_io_port); diff --git a/drivers/scsi/g_NCR5380.c b/drivers/scsi/g_NCR5380.c index 607336f56d55..75585a52c88b 100644 --- a/drivers/scsi/g_NCR5380.c +++ b/drivers/scsi/g_NCR5380.c @@ -460,7 +460,8 @@ int __init generic_NCR5380_detect(struct scsi_host_template * tpnt) instance->irq = NCR5380_probe_irq(instance, 0xffff); if (instance->irq != SCSI_IRQ_NONE) - if (request_irq(instance->irq, generic_NCR5380_intr, IRQF_DISABLED, "NCR5380", instance)) { + if (request_irq(instance->irq, generic_NCR5380_intr, + IRQF_DISABLED, "NCR5380", instance)) { printk(KERN_WARNING "scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); instance->irq = SCSI_IRQ_NONE; } @@ -513,7 +514,7 @@ int generic_NCR5380_release_resources(struct Scsi_Host *instance) NCR5380_setup(instance); if (instance->irq != SCSI_IRQ_NONE) - free_irq(instance->irq, NULL); + free_irq(instance->irq, instance); NCR5380_exit(instance); #ifndef CONFIG_SCSI_G_NCR5380_MEM diff --git a/drivers/scsi/iscsi_tcp.c b/drivers/scsi/iscsi_tcp.c index 4bcf916c21a7..57ce2251abc8 100644 --- a/drivers/scsi/iscsi_tcp.c +++ b/drivers/scsi/iscsi_tcp.c @@ -197,7 +197,7 @@ iscsi_tcp_cleanup_ctask(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) if (unlikely(!sc)) return; - tcp_ctask->xmstate = XMSTATE_IDLE; + tcp_ctask->xmstate = XMSTATE_VALUE_IDLE; tcp_ctask->r2t = NULL; } @@ -409,7 +409,7 @@ iscsi_r2t_rsp(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) tcp_ctask->exp_datasn = r2tsn + 1; __kfifo_put(tcp_ctask->r2tqueue, (void*)&r2t, sizeof(void*)); - tcp_ctask->xmstate |= XMSTATE_SOL_HDR_INIT; + set_bit(XMSTATE_BIT_SOL_HDR_INIT, &tcp_ctask->xmstate); list_move_tail(&ctask->running, &conn->xmitqueue); scsi_queue_work(session->host, &conn->xmitwork); @@ -1254,7 +1254,7 @@ static void iscsi_set_padding(struct iscsi_tcp_cmd_task *tcp_ctask, tcp_ctask->pad_count = ISCSI_PAD_LEN - tcp_ctask->pad_count; debug_scsi("write padding %d bytes\n", tcp_ctask->pad_count); - tcp_ctask->xmstate |= XMSTATE_W_PAD; + set_bit(XMSTATE_BIT_W_PAD, &tcp_ctask->xmstate); } /** @@ -1269,7 +1269,7 @@ iscsi_tcp_cmd_init(struct iscsi_cmd_task *ctask) struct iscsi_tcp_cmd_task *tcp_ctask = ctask->dd_data; BUG_ON(__kfifo_len(tcp_ctask->r2tqueue)); - tcp_ctask->xmstate = XMSTATE_CMD_HDR_INIT; + tcp_ctask->xmstate = 1 << XMSTATE_BIT_CMD_HDR_INIT; } /** @@ -1283,10 +1283,10 @@ iscsi_tcp_cmd_init(struct iscsi_cmd_task *ctask) * xmit. * * Management xmit state machine consists of these states: - * XMSTATE_IMM_HDR_INIT - calculate digest of PDU Header - * XMSTATE_IMM_HDR - PDU Header xmit in progress - * XMSTATE_IMM_DATA - PDU Data xmit in progress - * XMSTATE_IDLE - management PDU is done + * XMSTATE_BIT_IMM_HDR_INIT - calculate digest of PDU Header + * XMSTATE_BIT_IMM_HDR - PDU Header xmit in progress + * XMSTATE_BIT_IMM_DATA - PDU Data xmit in progress + * XMSTATE_VALUE_IDLE - management PDU is done **/ static int iscsi_tcp_mtask_xmit(struct iscsi_conn *conn, struct iscsi_mgmt_task *mtask) @@ -1297,12 +1297,12 @@ iscsi_tcp_mtask_xmit(struct iscsi_conn *conn, struct iscsi_mgmt_task *mtask) debug_scsi("mtask deq [cid %d state %x itt 0x%x]\n", conn->id, tcp_mtask->xmstate, mtask->itt); - if (tcp_mtask->xmstate & XMSTATE_IMM_HDR_INIT) { + if (test_bit(XMSTATE_BIT_IMM_HDR_INIT, &tcp_mtask->xmstate)) { iscsi_buf_init_iov(&tcp_mtask->headbuf, (char*)mtask->hdr, sizeof(struct iscsi_hdr)); if (mtask->data_count) { - tcp_mtask->xmstate |= XMSTATE_IMM_DATA; + set_bit(XMSTATE_BIT_IMM_DATA, &tcp_mtask->xmstate); iscsi_buf_init_iov(&tcp_mtask->sendbuf, (char*)mtask->data, mtask->data_count); @@ -1315,21 +1315,20 @@ iscsi_tcp_mtask_xmit(struct iscsi_conn *conn, struct iscsi_mgmt_task *mtask) (u8*)tcp_mtask->hdrext); tcp_mtask->sent = 0; - tcp_mtask->xmstate &= ~XMSTATE_IMM_HDR_INIT; - tcp_mtask->xmstate |= XMSTATE_IMM_HDR; + clear_bit(XMSTATE_BIT_IMM_HDR_INIT, &tcp_mtask->xmstate); + set_bit(XMSTATE_BIT_IMM_HDR, &tcp_mtask->xmstate); } - if (tcp_mtask->xmstate & XMSTATE_IMM_HDR) { + if (test_bit(XMSTATE_BIT_IMM_HDR, &tcp_mtask->xmstate)) { rc = iscsi_sendhdr(conn, &tcp_mtask->headbuf, mtask->data_count); if (rc) return rc; - tcp_mtask->xmstate &= ~XMSTATE_IMM_HDR; + clear_bit(XMSTATE_BIT_IMM_HDR, &tcp_mtask->xmstate); } - if (tcp_mtask->xmstate & XMSTATE_IMM_DATA) { + if (test_and_clear_bit(XMSTATE_BIT_IMM_DATA, &tcp_mtask->xmstate)) { BUG_ON(!mtask->data_count); - tcp_mtask->xmstate &= ~XMSTATE_IMM_DATA; /* FIXME: implement. * Virtual buffer could be spreaded across multiple pages... */ @@ -1339,13 +1338,13 @@ iscsi_tcp_mtask_xmit(struct iscsi_conn *conn, struct iscsi_mgmt_task *mtask) rc = iscsi_sendpage(conn, &tcp_mtask->sendbuf, &mtask->data_count, &tcp_mtask->sent); if (rc) { - tcp_mtask->xmstate |= XMSTATE_IMM_DATA; + set_bit(XMSTATE_BIT_IMM_DATA, &tcp_mtask->xmstate); return rc; } } while (mtask->data_count); } - BUG_ON(tcp_mtask->xmstate != XMSTATE_IDLE); + BUG_ON(tcp_mtask->xmstate != XMSTATE_VALUE_IDLE); if (mtask->hdr->itt == RESERVED_ITT) { struct iscsi_session *session = conn->session; @@ -1365,7 +1364,7 @@ iscsi_send_cmd_hdr(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) struct iscsi_tcp_cmd_task *tcp_ctask = ctask->dd_data; int rc = 0; - if (tcp_ctask->xmstate & XMSTATE_CMD_HDR_INIT) { + if (test_bit(XMSTATE_BIT_CMD_HDR_INIT, &tcp_ctask->xmstate)) { tcp_ctask->sent = 0; tcp_ctask->sg_count = 0; tcp_ctask->exp_datasn = 0; @@ -1390,21 +1389,21 @@ iscsi_send_cmd_hdr(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) if (conn->hdrdgst_en) iscsi_hdr_digest(conn, &tcp_ctask->headbuf, (u8*)tcp_ctask->hdrext); - tcp_ctask->xmstate &= ~XMSTATE_CMD_HDR_INIT; - tcp_ctask->xmstate |= XMSTATE_CMD_HDR_XMIT; + clear_bit(XMSTATE_BIT_CMD_HDR_INIT, &tcp_ctask->xmstate); + set_bit(XMSTATE_BIT_CMD_HDR_XMIT, &tcp_ctask->xmstate); } - if (tcp_ctask->xmstate & XMSTATE_CMD_HDR_XMIT) { + if (test_bit(XMSTATE_BIT_CMD_HDR_XMIT, &tcp_ctask->xmstate)) { rc = iscsi_sendhdr(conn, &tcp_ctask->headbuf, ctask->imm_count); if (rc) return rc; - tcp_ctask->xmstate &= ~XMSTATE_CMD_HDR_XMIT; + clear_bit(XMSTATE_BIT_CMD_HDR_XMIT, &tcp_ctask->xmstate); if (sc->sc_data_direction != DMA_TO_DEVICE) return 0; if (ctask->imm_count) { - tcp_ctask->xmstate |= XMSTATE_IMM_DATA; + set_bit(XMSTATE_BIT_IMM_DATA, &tcp_ctask->xmstate); iscsi_set_padding(tcp_ctask, ctask->imm_count); if (ctask->conn->datadgst_en) { @@ -1414,9 +1413,10 @@ iscsi_send_cmd_hdr(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) } } - if (ctask->unsol_count) - tcp_ctask->xmstate |= - XMSTATE_UNS_HDR | XMSTATE_UNS_INIT; + if (ctask->unsol_count) { + set_bit(XMSTATE_BIT_UNS_HDR, &tcp_ctask->xmstate); + set_bit(XMSTATE_BIT_UNS_INIT, &tcp_ctask->xmstate); + } } return rc; } @@ -1428,25 +1428,25 @@ iscsi_send_padding(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) struct iscsi_tcp_conn *tcp_conn = conn->dd_data; int sent = 0, rc; - if (tcp_ctask->xmstate & XMSTATE_W_PAD) { + if (test_bit(XMSTATE_BIT_W_PAD, &tcp_ctask->xmstate)) { iscsi_buf_init_iov(&tcp_ctask->sendbuf, (char*)&tcp_ctask->pad, tcp_ctask->pad_count); if (conn->datadgst_en) crypto_hash_update(&tcp_conn->tx_hash, &tcp_ctask->sendbuf.sg, tcp_ctask->sendbuf.sg.length); - } else if (!(tcp_ctask->xmstate & XMSTATE_W_RESEND_PAD)) + } else if (!test_bit(XMSTATE_BIT_W_RESEND_PAD, &tcp_ctask->xmstate)) return 0; - tcp_ctask->xmstate &= ~XMSTATE_W_PAD; - tcp_ctask->xmstate &= ~XMSTATE_W_RESEND_PAD; + clear_bit(XMSTATE_BIT_W_PAD, &tcp_ctask->xmstate); + clear_bit(XMSTATE_BIT_W_RESEND_PAD, &tcp_ctask->xmstate); debug_scsi("sending %d pad bytes for itt 0x%x\n", tcp_ctask->pad_count, ctask->itt); rc = iscsi_sendpage(conn, &tcp_ctask->sendbuf, &tcp_ctask->pad_count, &sent); if (rc) { debug_scsi("padding send failed %d\n", rc); - tcp_ctask->xmstate |= XMSTATE_W_RESEND_PAD; + set_bit(XMSTATE_BIT_W_RESEND_PAD, &tcp_ctask->xmstate); } return rc; } @@ -1465,11 +1465,11 @@ iscsi_send_digest(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask, tcp_ctask = ctask->dd_data; tcp_conn = conn->dd_data; - if (!(tcp_ctask->xmstate & XMSTATE_W_RESEND_DATA_DIGEST)) { + if (!test_bit(XMSTATE_BIT_W_RESEND_DATA_DIGEST, &tcp_ctask->xmstate)) { crypto_hash_final(&tcp_conn->tx_hash, (u8*)digest); iscsi_buf_init_iov(buf, (char*)digest, 4); } - tcp_ctask->xmstate &= ~XMSTATE_W_RESEND_DATA_DIGEST; + clear_bit(XMSTATE_BIT_W_RESEND_DATA_DIGEST, &tcp_ctask->xmstate); rc = iscsi_sendpage(conn, buf, &tcp_ctask->digest_count, &sent); if (!rc) @@ -1478,7 +1478,7 @@ iscsi_send_digest(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask, else { debug_scsi("sending digest 0x%x failed for itt 0x%x!\n", *digest, ctask->itt); - tcp_ctask->xmstate |= XMSTATE_W_RESEND_DATA_DIGEST; + set_bit(XMSTATE_BIT_W_RESEND_DATA_DIGEST, &tcp_ctask->xmstate); } return rc; } @@ -1526,8 +1526,8 @@ iscsi_send_unsol_hdr(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) struct iscsi_data_task *dtask; int rc; - tcp_ctask->xmstate |= XMSTATE_UNS_DATA; - if (tcp_ctask->xmstate & XMSTATE_UNS_INIT) { + set_bit(XMSTATE_BIT_UNS_DATA, &tcp_ctask->xmstate); + if (test_bit(XMSTATE_BIT_UNS_INIT, &tcp_ctask->xmstate)) { dtask = &tcp_ctask->unsol_dtask; iscsi_prep_unsolicit_data_pdu(ctask, &dtask->hdr); @@ -1537,14 +1537,14 @@ iscsi_send_unsol_hdr(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) iscsi_hdr_digest(conn, &tcp_ctask->headbuf, (u8*)dtask->hdrext); - tcp_ctask->xmstate &= ~XMSTATE_UNS_INIT; + clear_bit(XMSTATE_BIT_UNS_INIT, &tcp_ctask->xmstate); iscsi_set_padding(tcp_ctask, ctask->data_count); } rc = iscsi_sendhdr(conn, &tcp_ctask->headbuf, ctask->data_count); if (rc) { - tcp_ctask->xmstate &= ~XMSTATE_UNS_DATA; - tcp_ctask->xmstate |= XMSTATE_UNS_HDR; + clear_bit(XMSTATE_BIT_UNS_DATA, &tcp_ctask->xmstate); + set_bit(XMSTATE_BIT_UNS_HDR, &tcp_ctask->xmstate); return rc; } @@ -1565,16 +1565,15 @@ iscsi_send_unsol_pdu(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) struct iscsi_tcp_cmd_task *tcp_ctask = ctask->dd_data; int rc; - if (tcp_ctask->xmstate & XMSTATE_UNS_HDR) { + if (test_and_clear_bit(XMSTATE_BIT_UNS_HDR, &tcp_ctask->xmstate)) { BUG_ON(!ctask->unsol_count); - tcp_ctask->xmstate &= ~XMSTATE_UNS_HDR; send_hdr: rc = iscsi_send_unsol_hdr(conn, ctask); if (rc) return rc; } - if (tcp_ctask->xmstate & XMSTATE_UNS_DATA) { + if (test_bit(XMSTATE_BIT_UNS_DATA, &tcp_ctask->xmstate)) { struct iscsi_data_task *dtask = &tcp_ctask->unsol_dtask; int start = tcp_ctask->sent; @@ -1584,14 +1583,14 @@ send_hdr: ctask->unsol_count -= tcp_ctask->sent - start; if (rc) return rc; - tcp_ctask->xmstate &= ~XMSTATE_UNS_DATA; + clear_bit(XMSTATE_BIT_UNS_DATA, &tcp_ctask->xmstate); /* * Done with the Data-Out. Next, check if we need * to send another unsolicited Data-Out. */ if (ctask->unsol_count) { debug_scsi("sending more uns\n"); - tcp_ctask->xmstate |= XMSTATE_UNS_INIT; + set_bit(XMSTATE_BIT_UNS_INIT, &tcp_ctask->xmstate); goto send_hdr; } } @@ -1607,7 +1606,7 @@ static int iscsi_send_sol_pdu(struct iscsi_conn *conn, struct iscsi_data_task *dtask; int left, rc; - if (tcp_ctask->xmstate & XMSTATE_SOL_HDR_INIT) { + if (test_bit(XMSTATE_BIT_SOL_HDR_INIT, &tcp_ctask->xmstate)) { if (!tcp_ctask->r2t) { spin_lock_bh(&session->lock); __kfifo_get(tcp_ctask->r2tqueue, (void*)&tcp_ctask->r2t, @@ -1621,19 +1620,19 @@ send_hdr: if (conn->hdrdgst_en) iscsi_hdr_digest(conn, &r2t->headbuf, (u8*)dtask->hdrext); - tcp_ctask->xmstate &= ~XMSTATE_SOL_HDR_INIT; - tcp_ctask->xmstate |= XMSTATE_SOL_HDR; + clear_bit(XMSTATE_BIT_SOL_HDR_INIT, &tcp_ctask->xmstate); + set_bit(XMSTATE_BIT_SOL_HDR, &tcp_ctask->xmstate); } - if (tcp_ctask->xmstate & XMSTATE_SOL_HDR) { + if (test_bit(XMSTATE_BIT_SOL_HDR, &tcp_ctask->xmstate)) { r2t = tcp_ctask->r2t; dtask = &r2t->dtask; rc = iscsi_sendhdr(conn, &r2t->headbuf, r2t->data_count); if (rc) return rc; - tcp_ctask->xmstate &= ~XMSTATE_SOL_HDR; - tcp_ctask->xmstate |= XMSTATE_SOL_DATA; + clear_bit(XMSTATE_BIT_SOL_HDR, &tcp_ctask->xmstate); + set_bit(XMSTATE_BIT_SOL_DATA, &tcp_ctask->xmstate); if (conn->datadgst_en) { iscsi_data_digest_init(conn->dd_data, tcp_ctask); @@ -1646,7 +1645,7 @@ send_hdr: r2t->sent); } - if (tcp_ctask->xmstate & XMSTATE_SOL_DATA) { + if (test_bit(XMSTATE_BIT_SOL_DATA, &tcp_ctask->xmstate)) { r2t = tcp_ctask->r2t; dtask = &r2t->dtask; @@ -1655,7 +1654,7 @@ send_hdr: &dtask->digestbuf, &dtask->digest); if (rc) return rc; - tcp_ctask->xmstate &= ~XMSTATE_SOL_DATA; + clear_bit(XMSTATE_BIT_SOL_DATA, &tcp_ctask->xmstate); /* * Done with this Data-Out. Next, check if we have @@ -1700,32 +1699,32 @@ send_hdr: * xmit stages. * *iscsi_send_cmd_hdr() - * XMSTATE_CMD_HDR_INIT - prepare Header and Data buffers Calculate - * Header Digest - * XMSTATE_CMD_HDR_XMIT - Transmit header in progress + * XMSTATE_BIT_CMD_HDR_INIT - prepare Header and Data buffers Calculate + * Header Digest + * XMSTATE_BIT_CMD_HDR_XMIT - Transmit header in progress * *iscsi_send_padding - * XMSTATE_W_PAD - Prepare and send pading - * XMSTATE_W_RESEND_PAD - retry send pading + * XMSTATE_BIT_W_PAD - Prepare and send pading + * XMSTATE_BIT_W_RESEND_PAD - retry send pading * *iscsi_send_digest - * XMSTATE_W_RESEND_DATA_DIGEST - Finalize and send Data Digest - * XMSTATE_W_RESEND_DATA_DIGEST - retry sending digest + * XMSTATE_BIT_W_RESEND_DATA_DIGEST - Finalize and send Data Digest + * XMSTATE_BIT_W_RESEND_DATA_DIGEST - retry sending digest * *iscsi_send_unsol_hdr - * XMSTATE_UNS_INIT - prepare un-solicit data header and digest - * XMSTATE_UNS_HDR - send un-solicit header + * XMSTATE_BIT_UNS_INIT - prepare un-solicit data header and digest + * XMSTATE_BIT_UNS_HDR - send un-solicit header * *iscsi_send_unsol_pdu - * XMSTATE_UNS_DATA - send un-solicit data in progress + * XMSTATE_BIT_UNS_DATA - send un-solicit data in progress * *iscsi_send_sol_pdu - * XMSTATE_SOL_HDR_INIT - solicit data header and digest initialize - * XMSTATE_SOL_HDR - send solicit header - * XMSTATE_SOL_DATA - send solicit data + * XMSTATE_BIT_SOL_HDR_INIT - solicit data header and digest initialize + * XMSTATE_BIT_SOL_HDR - send solicit header + * XMSTATE_BIT_SOL_DATA - send solicit data * *iscsi_tcp_ctask_xmit - * XMSTATE_IMM_DATA - xmit managment data (??) + * XMSTATE_BIT_IMM_DATA - xmit managment data (??) **/ static int iscsi_tcp_ctask_xmit(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) @@ -1742,13 +1741,13 @@ iscsi_tcp_ctask_xmit(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask) if (ctask->sc->sc_data_direction != DMA_TO_DEVICE) return 0; - if (tcp_ctask->xmstate & XMSTATE_IMM_DATA) { + if (test_bit(XMSTATE_BIT_IMM_DATA, &tcp_ctask->xmstate)) { rc = iscsi_send_data(ctask, &tcp_ctask->sendbuf, &tcp_ctask->sg, &tcp_ctask->sent, &ctask->imm_count, &tcp_ctask->immbuf, &tcp_ctask->immdigest); if (rc) return rc; - tcp_ctask->xmstate &= ~XMSTATE_IMM_DATA; + clear_bit(XMSTATE_BIT_IMM_DATA, &tcp_ctask->xmstate); } rc = iscsi_send_unsol_pdu(conn, ctask); @@ -1981,7 +1980,7 @@ static void iscsi_tcp_mgmt_init(struct iscsi_conn *conn, struct iscsi_mgmt_task *mtask) { struct iscsi_tcp_mgmt_task *tcp_mtask = mtask->dd_data; - tcp_mtask->xmstate = XMSTATE_IMM_HDR_INIT; + tcp_mtask->xmstate = 1 << XMSTATE_BIT_IMM_HDR_INIT; } static int diff --git a/drivers/scsi/iscsi_tcp.h b/drivers/scsi/iscsi_tcp.h index 7eba44df0a7f..68c36cc8997e 100644 --- a/drivers/scsi/iscsi_tcp.h +++ b/drivers/scsi/iscsi_tcp.h @@ -32,21 +32,21 @@ #define IN_PROGRESS_PAD_RECV 0x4 /* xmit state machine */ -#define XMSTATE_IDLE 0x0 -#define XMSTATE_CMD_HDR_INIT 0x1 -#define XMSTATE_CMD_HDR_XMIT 0x2 -#define XMSTATE_IMM_HDR 0x4 -#define XMSTATE_IMM_DATA 0x8 -#define XMSTATE_UNS_INIT 0x10 -#define XMSTATE_UNS_HDR 0x20 -#define XMSTATE_UNS_DATA 0x40 -#define XMSTATE_SOL_HDR 0x80 -#define XMSTATE_SOL_DATA 0x100 -#define XMSTATE_W_PAD 0x200 -#define XMSTATE_W_RESEND_PAD 0x400 -#define XMSTATE_W_RESEND_DATA_DIGEST 0x800 -#define XMSTATE_IMM_HDR_INIT 0x1000 -#define XMSTATE_SOL_HDR_INIT 0x2000 +#define XMSTATE_VALUE_IDLE 0 +#define XMSTATE_BIT_CMD_HDR_INIT 0 +#define XMSTATE_BIT_CMD_HDR_XMIT 1 +#define XMSTATE_BIT_IMM_HDR 2 +#define XMSTATE_BIT_IMM_DATA 3 +#define XMSTATE_BIT_UNS_INIT 4 +#define XMSTATE_BIT_UNS_HDR 5 +#define XMSTATE_BIT_UNS_DATA 6 +#define XMSTATE_BIT_SOL_HDR 7 +#define XMSTATE_BIT_SOL_DATA 8 +#define XMSTATE_BIT_W_PAD 9 +#define XMSTATE_BIT_W_RESEND_PAD 10 +#define XMSTATE_BIT_W_RESEND_DATA_DIGEST 11 +#define XMSTATE_BIT_IMM_HDR_INIT 12 +#define XMSTATE_BIT_SOL_HDR_INIT 13 #define ISCSI_PAD_LEN 4 #define ISCSI_SG_TABLESIZE SG_ALL @@ -122,7 +122,7 @@ struct iscsi_data_task { struct iscsi_tcp_mgmt_task { struct iscsi_hdr hdr; char hdrext[sizeof(__u32)]; /* Header-Digest */ - int xmstate; /* mgmt xmit progress */ + unsigned long xmstate; /* mgmt xmit progress */ struct iscsi_buf headbuf; /* header buffer */ struct iscsi_buf sendbuf; /* in progress buffer */ int sent; @@ -150,7 +150,7 @@ struct iscsi_tcp_cmd_task { int pad_count; /* padded bytes */ struct iscsi_buf headbuf; /* header buf (xmit) */ struct iscsi_buf sendbuf; /* in progress buffer*/ - int xmstate; /* xmit xtate machine */ + unsigned long xmstate; /* xmit xtate machine */ int sent; struct scatterlist *sg; /* per-cmd SG list */ struct scatterlist *bad_sg; /* assert statement */ diff --git a/drivers/scsi/libiscsi.c b/drivers/scsi/libiscsi.c index efceed451b46..8b57af5baaec 100644 --- a/drivers/scsi/libiscsi.c +++ b/drivers/scsi/libiscsi.c @@ -291,9 +291,6 @@ invalid_datalen: min_t(uint16_t, senselen, SCSI_SENSE_BUFFERSIZE)); } - if (sc->sc_data_direction == DMA_TO_DEVICE) - goto out; - if (rhdr->flags & ISCSI_FLAG_CMD_UNDERFLOW) { int res_count = be32_to_cpu(rhdr->residual_count); diff --git a/drivers/scsi/mac_scsi.c b/drivers/scsi/mac_scsi.c index abe2bda6ac37..3b09ab21d701 100644 --- a/drivers/scsi/mac_scsi.c +++ b/drivers/scsi/mac_scsi.c @@ -303,7 +303,7 @@ int macscsi_detect(struct scsi_host_template * tpnt) if (instance->irq != SCSI_IRQ_NONE) if (request_irq(instance->irq, NCR5380_intr, IRQ_FLG_SLOW, - "ncr5380", instance)) { + "ncr5380", instance)) { printk(KERN_WARNING "scsi%d: IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); instance->irq = SCSI_IRQ_NONE; @@ -326,7 +326,7 @@ int macscsi_detect(struct scsi_host_template * tpnt) int macscsi_release (struct Scsi_Host *shpnt) { if (shpnt->irq != SCSI_IRQ_NONE) - free_irq (shpnt->irq, NCR5380_intr); + free_irq(shpnt->irq, shpnt); NCR5380_exit(shpnt); return 0; diff --git a/drivers/scsi/pas16.c b/drivers/scsi/pas16.c index ee5965659971..f2018b46f494 100644 --- a/drivers/scsi/pas16.c +++ b/drivers/scsi/pas16.c @@ -453,7 +453,8 @@ int __init pas16_detect(struct scsi_host_template * tpnt) instance->irq = NCR5380_probe_irq(instance, PAS16_IRQS); if (instance->irq != SCSI_IRQ_NONE) - if (request_irq(instance->irq, pas16_intr, IRQF_DISABLED, "pas16", instance)) { + if (request_irq(instance->irq, pas16_intr, IRQF_DISABLED, + "pas16", instance)) { printk("scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); instance->irq = SCSI_IRQ_NONE; @@ -604,7 +605,7 @@ static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src static int pas16_release(struct Scsi_Host *shost) { if (shost->irq) - free_irq(shost->irq, NULL); + free_irq(shost->irq, shost); NCR5380_exit(shost); if (shost->dma_channel != 0xff) free_dma(shost->dma_channel); diff --git a/drivers/scsi/qla1280.c b/drivers/scsi/qla1280.c index 3aeb68bcb7ac..146d540f6281 100644 --- a/drivers/scsi/qla1280.c +++ b/drivers/scsi/qla1280.c @@ -1310,14 +1310,7 @@ qla1280_done(struct scsi_qla_host *ha) } /* Release memory used for this I/O */ - if (cmd->use_sg) { - pci_unmap_sg(ha->pdev, cmd->request_buffer, - cmd->use_sg, cmd->sc_data_direction); - } else if (cmd->request_bufflen) { - pci_unmap_single(ha->pdev, sp->saved_dma_handle, - cmd->request_bufflen, - cmd->sc_data_direction); - } + scsi_dma_unmap(cmd); /* Call the mid-level driver interrupt handler */ CMD_HANDLE(sp->cmd) = (unsigned char *)INVALID_HANDLE; @@ -1406,14 +1399,14 @@ qla1280_return_status(struct response * sts, struct scsi_cmnd *cp) break; case CS_DATA_UNDERRUN: - if ((cp->request_bufflen - residual_length) < + if ((scsi_bufflen(cp) - residual_length) < cp->underflow) { printk(KERN_WARNING "scsi: Underflow detected - retrying " "command.\n"); host_status = DID_ERROR; } else { - cp->resid = residual_length; + scsi_set_resid(cp, residual_length); host_status = DID_OK; } break; @@ -2775,33 +2768,28 @@ qla1280_64bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp) struct device_reg __iomem *reg = ha->iobase; struct scsi_cmnd *cmd = sp->cmd; cmd_a64_entry_t *pkt; - struct scatterlist *sg = NULL, *s; __le32 *dword_ptr; dma_addr_t dma_handle; int status = 0; int cnt; int req_cnt; - u16 seg_cnt; + int seg_cnt; u8 dir; ENTER("qla1280_64bit_start_scsi:"); /* Calculate number of entries and segments required. */ req_cnt = 1; - if (cmd->use_sg) { - sg = (struct scatterlist *) cmd->request_buffer; - seg_cnt = pci_map_sg(ha->pdev, sg, cmd->use_sg, - cmd->sc_data_direction); - + seg_cnt = scsi_dma_map(cmd); + if (seg_cnt > 0) { if (seg_cnt > 2) { req_cnt += (seg_cnt - 2) / 5; if ((seg_cnt - 2) % 5) req_cnt++; } - } else if (cmd->request_bufflen) { /* If data transfer. */ - seg_cnt = 1; - } else { - seg_cnt = 0; + } else if (seg_cnt < 0) { + status = 1; + goto out; } if ((req_cnt + 2) >= ha->req_q_cnt) { @@ -2889,124 +2877,104 @@ qla1280_64bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp) * Load data segments. */ if (seg_cnt) { /* If data transfer. */ + struct scatterlist *sg, *s; int remseg = seg_cnt; + + sg = scsi_sglist(cmd); + /* Setup packet address segment pointer. */ dword_ptr = (u32 *)&pkt->dseg_0_address; - if (cmd->use_sg) { /* If scatter gather */ - /* Load command entry data segments. */ - for_each_sg(sg, s, seg_cnt, cnt) { - if (cnt == 2) + /* Load command entry data segments. */ + for_each_sg(sg, s, seg_cnt, cnt) { + if (cnt == 2) + break; + + dma_handle = sg_dma_address(s); +#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2) + if (ha->flags.use_pci_vchannel) + sn_pci_set_vchan(ha->pdev, + (unsigned long *)&dma_handle, + SCSI_BUS_32(cmd)); +#endif + *dword_ptr++ = + cpu_to_le32(pci_dma_lo32(dma_handle)); + *dword_ptr++ = + cpu_to_le32(pci_dma_hi32(dma_handle)); + *dword_ptr++ = cpu_to_le32(sg_dma_len(s)); + dprintk(3, "S/G Segment phys_addr=%x %x, len=0x%x\n", + cpu_to_le32(pci_dma_hi32(dma_handle)), + cpu_to_le32(pci_dma_lo32(dma_handle)), + cpu_to_le32(sg_dma_len(sg_next(s)))); + remseg--; + } + dprintk(5, "qla1280_64bit_start_scsi: Scatter/gather " + "command packet data - b %i, t %i, l %i \n", + SCSI_BUS_32(cmd), SCSI_TCN_32(cmd), + SCSI_LUN_32(cmd)); + qla1280_dump_buffer(5, (char *)pkt, + REQUEST_ENTRY_SIZE); + + /* + * Build continuation packets. + */ + dprintk(3, "S/G Building Continuation...seg_cnt=0x%x " + "remains\n", seg_cnt); + + while (remseg > 0) { + /* Update sg start */ + sg = s; + /* Adjust ring index. */ + ha->req_ring_index++; + if (ha->req_ring_index == REQUEST_ENTRY_CNT) { + ha->req_ring_index = 0; + ha->request_ring_ptr = + ha->request_ring; + } else + ha->request_ring_ptr++; + + pkt = (cmd_a64_entry_t *)ha->request_ring_ptr; + + /* Zero out packet. */ + memset(pkt, 0, REQUEST_ENTRY_SIZE); + + /* Load packet defaults. */ + ((struct cont_a64_entry *) pkt)->entry_type = + CONTINUE_A64_TYPE; + ((struct cont_a64_entry *) pkt)->entry_count = 1; + ((struct cont_a64_entry *) pkt)->sys_define = + (uint8_t)ha->req_ring_index; + /* Setup packet address segment pointer. */ + dword_ptr = + (u32 *)&((struct cont_a64_entry *) pkt)->dseg_0_address; + + /* Load continuation entry data segments. */ + for_each_sg(sg, s, remseg, cnt) { + if (cnt == 5) break; dma_handle = sg_dma_address(s); #if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2) if (ha->flags.use_pci_vchannel) sn_pci_set_vchan(ha->pdev, - (unsigned long *)&dma_handle, + (unsigned long *)&dma_handle, SCSI_BUS_32(cmd)); #endif *dword_ptr++ = cpu_to_le32(pci_dma_lo32(dma_handle)); *dword_ptr++ = cpu_to_le32(pci_dma_hi32(dma_handle)); - *dword_ptr++ = cpu_to_le32(sg_dma_len(s)); - dprintk(3, "S/G Segment phys_addr=%x %x, len=0x%x\n", + *dword_ptr++ = + cpu_to_le32(sg_dma_len(s)); + dprintk(3, "S/G Segment Cont. phys_addr=%x %x, len=0x%x\n", cpu_to_le32(pci_dma_hi32(dma_handle)), cpu_to_le32(pci_dma_lo32(dma_handle)), - cpu_to_le32(sg_dma_len(sg_next(s)))); - remseg--; + cpu_to_le32(sg_dma_len(s))); } - dprintk(5, "qla1280_64bit_start_scsi: Scatter/gather " - "command packet data - b %i, t %i, l %i \n", - SCSI_BUS_32(cmd), SCSI_TCN_32(cmd), - SCSI_LUN_32(cmd)); - qla1280_dump_buffer(5, (char *)pkt, - REQUEST_ENTRY_SIZE); - - /* - * Build continuation packets. - */ - dprintk(3, "S/G Building Continuation...seg_cnt=0x%x " - "remains\n", seg_cnt); - - while (remseg > 0) { - /* Update sg start */ - sg = s; - /* Adjust ring index. */ - ha->req_ring_index++; - if (ha->req_ring_index == REQUEST_ENTRY_CNT) { - ha->req_ring_index = 0; - ha->request_ring_ptr = - ha->request_ring; - } else - ha->request_ring_ptr++; - - pkt = (cmd_a64_entry_t *)ha->request_ring_ptr; - - /* Zero out packet. */ - memset(pkt, 0, REQUEST_ENTRY_SIZE); - - /* Load packet defaults. */ - ((struct cont_a64_entry *) pkt)->entry_type = - CONTINUE_A64_TYPE; - ((struct cont_a64_entry *) pkt)->entry_count = 1; - ((struct cont_a64_entry *) pkt)->sys_define = - (uint8_t)ha->req_ring_index; - /* Setup packet address segment pointer. */ - dword_ptr = - (u32 *)&((struct cont_a64_entry *) pkt)->dseg_0_address; - - /* Load continuation entry data segments. */ - for_each_sg(sg, s, remseg, cnt) { - if (cnt == 5) - break; - dma_handle = sg_dma_address(s); -#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2) - if (ha->flags.use_pci_vchannel) - sn_pci_set_vchan(ha->pdev, - (unsigned long *)&dma_handle, - SCSI_BUS_32(cmd)); -#endif - *dword_ptr++ = - cpu_to_le32(pci_dma_lo32(dma_handle)); - *dword_ptr++ = - cpu_to_le32(pci_dma_hi32(dma_handle)); - *dword_ptr++ = - cpu_to_le32(sg_dma_len(s)); - dprintk(3, "S/G Segment Cont. phys_addr=%x %x, len=0x%x\n", - cpu_to_le32(pci_dma_hi32(dma_handle)), - cpu_to_le32(pci_dma_lo32(dma_handle)), - cpu_to_le32(sg_dma_len(s))); - } - remseg -= cnt; - dprintk(5, "qla1280_64bit_start_scsi: " - "continuation packet data - b %i, t " - "%i, l %i \n", SCSI_BUS_32(cmd), - SCSI_TCN_32(cmd), SCSI_LUN_32(cmd)); - qla1280_dump_buffer(5, (char *)pkt, - REQUEST_ENTRY_SIZE); - } - } else { /* No scatter gather data transfer */ - dma_handle = pci_map_single(ha->pdev, - cmd->request_buffer, - cmd->request_bufflen, - cmd->sc_data_direction); - - sp->saved_dma_handle = dma_handle; -#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2) - if (ha->flags.use_pci_vchannel) - sn_pci_set_vchan(ha->pdev, - (unsigned long *)&dma_handle, - SCSI_BUS_32(cmd)); -#endif - *dword_ptr++ = cpu_to_le32(pci_dma_lo32(dma_handle)); - *dword_ptr++ = cpu_to_le32(pci_dma_hi32(dma_handle)); - *dword_ptr = cpu_to_le32(cmd->request_bufflen); - - dprintk(5, "qla1280_64bit_start_scsi: No scatter/" - "gather command packet data - b %i, t %i, " - "l %i \n", SCSI_BUS_32(cmd), SCSI_TCN_32(cmd), - SCSI_LUN_32(cmd)); + remseg -= cnt; + dprintk(5, "qla1280_64bit_start_scsi: " + "continuation packet data - b %i, t " + "%i, l %i \n", SCSI_BUS_32(cmd), + SCSI_TCN_32(cmd), SCSI_LUN_32(cmd)); qla1280_dump_buffer(5, (char *)pkt, REQUEST_ENTRY_SIZE); } @@ -3068,12 +3036,11 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp) struct device_reg __iomem *reg = ha->iobase; struct scsi_cmnd *cmd = sp->cmd; struct cmd_entry *pkt; - struct scatterlist *sg = NULL, *s; __le32 *dword_ptr; int status = 0; int cnt; int req_cnt; - uint16_t seg_cnt; + int seg_cnt; dma_addr_t dma_handle; u8 dir; @@ -3083,18 +3050,8 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp) cmd->cmnd[0]); /* Calculate number of entries and segments required. */ - req_cnt = 1; - if (cmd->use_sg) { - /* - * We must build an SG list in adapter format, as the kernel's - * SG list cannot be used directly because of data field size - * (__alpha__) differences and the kernel SG list uses virtual - * addresses where we need physical addresses. - */ - sg = (struct scatterlist *) cmd->request_buffer; - seg_cnt = pci_map_sg(ha->pdev, sg, cmd->use_sg, - cmd->sc_data_direction); - + seg_cnt = scsi_dma_map(cmd); + if (seg_cnt) { /* * if greater than four sg entries then we need to allocate * continuation entries @@ -3106,14 +3063,9 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp) } dprintk(3, "S/G Transfer cmd=%p seg_cnt=0x%x, req_cnt=%x\n", cmd, seg_cnt, req_cnt); - } else if (cmd->request_bufflen) { /* If data transfer. */ - dprintk(3, "No S/G transfer t=%x cmd=%p len=%x CDB=%x\n", - SCSI_TCN_32(cmd), cmd, cmd->request_bufflen, - cmd->cmnd[0]); - seg_cnt = 1; - } else { - /* dprintk(1, "No data transfer \n"); */ - seg_cnt = 0; + } else if (seg_cnt < 0) { + status = 1; + goto out; } if ((req_cnt + 2) >= ha->req_q_cnt) { @@ -3194,91 +3146,84 @@ qla1280_32bit_start_scsi(struct scsi_qla_host *ha, struct srb * sp) * Load data segments. */ if (seg_cnt) { + struct scatterlist *sg, *s; int remseg = seg_cnt; + + sg = scsi_sglist(cmd); + /* Setup packet address segment pointer. */ dword_ptr = &pkt->dseg_0_address; - if (cmd->use_sg) { /* If scatter gather */ - dprintk(3, "Building S/G data segments..\n"); - qla1280_dump_buffer(1, (char *)sg, 4 * 16); + dprintk(3, "Building S/G data segments..\n"); + qla1280_dump_buffer(1, (char *)sg, 4 * 16); + + /* Load command entry data segments. */ + for_each_sg(sg, s, seg_cnt, cnt) { + if (cnt == 4) + break; + *dword_ptr++ = + cpu_to_le32(pci_dma_lo32(sg_dma_address(s))); + *dword_ptr++ = cpu_to_le32(sg_dma_len(s)); + dprintk(3, "S/G Segment phys_addr=0x%lx, len=0x%x\n", + (pci_dma_lo32(sg_dma_address(s))), + (sg_dma_len(s))); + remseg--; + } + /* + * Build continuation packets. + */ + dprintk(3, "S/G Building Continuation" + "...seg_cnt=0x%x remains\n", seg_cnt); + while (remseg > 0) { + /* Continue from end point */ + sg = s; + /* Adjust ring index. */ + ha->req_ring_index++; + if (ha->req_ring_index == REQUEST_ENTRY_CNT) { + ha->req_ring_index = 0; + ha->request_ring_ptr = + ha->request_ring; + } else + ha->request_ring_ptr++; + + pkt = (struct cmd_entry *)ha->request_ring_ptr; + + /* Zero out packet. */ + memset(pkt, 0, REQUEST_ENTRY_SIZE); + + /* Load packet defaults. */ + ((struct cont_entry *) pkt)-> + entry_type = CONTINUE_TYPE; + ((struct cont_entry *) pkt)->entry_count = 1; - /* Load command entry data segments. */ - for_each_sg(sg, s, seg_cnt, cnt) { - if (cnt == 4) + ((struct cont_entry *) pkt)->sys_define = + (uint8_t) ha->req_ring_index; + + /* Setup packet address segment pointer. */ + dword_ptr = + &((struct cont_entry *) pkt)->dseg_0_address; + + /* Load continuation entry data segments. */ + for_each_sg(sg, s, remseg, cnt) { + if (cnt == 7) break; *dword_ptr++ = cpu_to_le32(pci_dma_lo32(sg_dma_address(s))); - *dword_ptr++ = cpu_to_le32(sg_dma_len(s)); - dprintk(3, "S/G Segment phys_addr=0x%lx, len=0x%x\n", - (pci_dma_lo32(sg_dma_address(s))), - (sg_dma_len(s))); - remseg--; - } - /* - * Build continuation packets. - */ - dprintk(3, "S/G Building Continuation" - "...seg_cnt=0x%x remains\n", seg_cnt); - while (remseg > 0) { - /* Continue from end point */ - sg = s; - /* Adjust ring index. */ - ha->req_ring_index++; - if (ha->req_ring_index == REQUEST_ENTRY_CNT) { - ha->req_ring_index = 0; - ha->request_ring_ptr = - ha->request_ring; - } else - ha->request_ring_ptr++; - - pkt = (struct cmd_entry *)ha->request_ring_ptr; - - /* Zero out packet. */ - memset(pkt, 0, REQUEST_ENTRY_SIZE); - - /* Load packet defaults. */ - ((struct cont_entry *) pkt)-> - entry_type = CONTINUE_TYPE; - ((struct cont_entry *) pkt)->entry_count = 1; - - ((struct cont_entry *) pkt)->sys_define = - (uint8_t) ha->req_ring_index; - - /* Setup packet address segment pointer. */ - dword_ptr = - &((struct cont_entry *) pkt)->dseg_0_address; - - /* Load continuation entry data segments. */ - for_each_sg(sg, s, remseg, cnt) { - if (cnt == 7) - break; - *dword_ptr++ = - cpu_to_le32(pci_dma_lo32(sg_dma_address(s))); - *dword_ptr++ = - cpu_to_le32(sg_dma_len(s)); - dprintk(1, - "S/G Segment Cont. phys_addr=0x%x, " - "len=0x%x\n", - cpu_to_le32(pci_dma_lo32(sg_dma_address(s))), - cpu_to_le32(sg_dma_len(s))); - } - remseg -= cnt; - dprintk(5, "qla1280_32bit_start_scsi: " - "continuation packet data - " - "scsi(%i:%i:%i)\n", SCSI_BUS_32(cmd), - SCSI_TCN_32(cmd), SCSI_LUN_32(cmd)); - qla1280_dump_buffer(5, (char *)pkt, - REQUEST_ENTRY_SIZE); + *dword_ptr++ = + cpu_to_le32(sg_dma_len(s)); + dprintk(1, + "S/G Segment Cont. phys_addr=0x%x, " + "len=0x%x\n", + cpu_to_le32(pci_dma_lo32(sg_dma_address(s))), + cpu_to_le32(sg_dma_len(s))); } - } else { /* No S/G data transfer */ - dma_handle = pci_map_single(ha->pdev, - cmd->request_buffer, - cmd->request_bufflen, - cmd->sc_data_direction); - sp->saved_dma_handle = dma_handle; - - *dword_ptr++ = cpu_to_le32(pci_dma_lo32(dma_handle)); - *dword_ptr = cpu_to_le32(cmd->request_bufflen); + remseg -= cnt; + dprintk(5, "qla1280_32bit_start_scsi: " + "continuation packet data - " + "scsi(%i:%i:%i)\n", SCSI_BUS_32(cmd), + SCSI_TCN_32(cmd), SCSI_LUN_32(cmd)); + qla1280_dump_buffer(5, (char *)pkt, + REQUEST_ENTRY_SIZE); } } else { /* No data transfer at all */ dprintk(5, "qla1280_32bit_start_scsi: No data, command " @@ -4086,9 +4031,9 @@ __qla1280_print_scsi_cmd(struct scsi_cmnd *cmd) for (i = 0; i < cmd->cmd_len; i++) { printk("0x%02x ", cmd->cmnd[i]); } - printk(" seg_cnt =%d\n", cmd->use_sg); + printk(" seg_cnt =%d\n", scsi_sg_count(cmd)); printk(" request buffer=0x%p, request buffer len=0x%x\n", - cmd->request_buffer, cmd->request_bufflen); + scsi_sglist(cmd), scsi_bufflen(cmd)); /* if (cmd->use_sg) { sg = (struct scatterlist *) cmd->request_buffer; diff --git a/drivers/scsi/sun3_scsi.c b/drivers/scsi/sun3_scsi.c index 5e46d842c6f9..e606cf0a2eb7 100644 --- a/drivers/scsi/sun3_scsi.c +++ b/drivers/scsi/sun3_scsi.c @@ -268,7 +268,7 @@ int sun3scsi_detect(struct scsi_host_template * tpnt) ((struct NCR5380_hostdata *)instance->hostdata)->ctrl = 0; if (request_irq(instance->irq, scsi_sun3_intr, - 0, "Sun3SCSI-5380", NULL)) { + 0, "Sun3SCSI-5380", instance)) { #ifndef REAL_DMA printk("scsi%d: IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); @@ -310,7 +310,7 @@ int sun3scsi_detect(struct scsi_host_template * tpnt) int sun3scsi_release (struct Scsi_Host *shpnt) { if (shpnt->irq != SCSI_IRQ_NONE) - free_irq (shpnt->irq, NULL); + free_irq(shpnt->irq, shpnt); iounmap((void *)sun3_scsi_regp); diff --git a/drivers/scsi/sun3_scsi_vme.c b/drivers/scsi/sun3_scsi_vme.c index 7cb4a31453e6..02d9727f017a 100644 --- a/drivers/scsi/sun3_scsi_vme.c +++ b/drivers/scsi/sun3_scsi_vme.c @@ -230,7 +230,7 @@ static int sun3scsi_detect(struct scsi_host_template * tpnt) ((struct NCR5380_hostdata *)instance->hostdata)->ctrl = 0; if (request_irq(instance->irq, scsi_sun3_intr, - 0, "Sun3SCSI-5380VME", NULL)) { + 0, "Sun3SCSI-5380VME", instance)) { #ifndef REAL_DMA printk("scsi%d: IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); @@ -279,7 +279,7 @@ static int sun3scsi_detect(struct scsi_host_template * tpnt) int sun3scsi_release (struct Scsi_Host *shpnt) { if (shpnt->irq != SCSI_IRQ_NONE) - free_irq (shpnt->irq, NULL); + free_irq(shpnt->irq, shpnt); iounmap((void *)sun3_scsi_regp); diff --git a/drivers/scsi/t128.c b/drivers/scsi/t128.c index 248d60b8d899..041eaaace2c3 100644 --- a/drivers/scsi/t128.c +++ b/drivers/scsi/t128.c @@ -259,7 +259,8 @@ found: instance->irq = NCR5380_probe_irq(instance, T128_IRQS); if (instance->irq != SCSI_IRQ_NONE) - if (request_irq(instance->irq, t128_intr, IRQF_DISABLED, "t128", instance)) { + if (request_irq(instance->irq, t128_intr, IRQF_DISABLED, "t128", + instance)) { printk("scsi%d : IRQ%d not free, interrupts disabled\n", instance->host_no, instance->irq); instance->irq = SCSI_IRQ_NONE; @@ -295,7 +296,7 @@ static int t128_release(struct Scsi_Host *shost) NCR5380_local_declare(); NCR5380_setup(shost); if (shost->irq) - free_irq(shost->irq, NULL); + free_irq(shost->irq, shost); NCR5380_exit(shost); if (shost->io_port && shost->n_io_port) release_region(shost->io_port, shost->n_io_port); diff --git a/drivers/spi/at25.c b/drivers/spi/at25.c index e007833cca59..290dbe99647a 100644 --- a/drivers/spi/at25.c +++ b/drivers/spi/at25.c @@ -21,6 +21,13 @@ #include <linux/spi/eeprom.h> +/* + * NOTE: this is an *EEPROM* driver. The vagaries of product naming + * mean that some AT25 products are EEPROMs, and others are FLASH. + * Handle FLASH chips with the drivers/mtd/devices/m25p80.c driver, + * not this one! + */ + struct at25_data { struct spi_device *spi; struct mutex lock; diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index b31f4431849b..93e9de46977a 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -541,10 +541,7 @@ static void spi_complete(void *arg) * Also, the caller is guaranteeing that the memory associated with the * message will not be freed before this call returns. * - * The return value is a negative error code if the message could not be - * submitted, else zero. When the value is zero, then message->status is - * also defined; it's the completion code for the transfer, either zero - * or a negative error code from the controller driver. + * It returns zero on success, else a negative error code. */ int spi_sync(struct spi_device *spi, struct spi_message *message) { @@ -554,8 +551,10 @@ int spi_sync(struct spi_device *spi, struct spi_message *message) message->complete = spi_complete; message->context = &done; status = spi_async(spi, message); - if (status == 0) + if (status == 0) { wait_for_completion(&done); + status = message->status; + } message->context = NULL; return status; } @@ -589,7 +588,7 @@ int spi_write_then_read(struct spi_device *spi, const u8 *txbuf, unsigned n_tx, u8 *rxbuf, unsigned n_rx) { - static DECLARE_MUTEX(lock); + static DEFINE_MUTEX(lock); int status; struct spi_message message; @@ -615,7 +614,7 @@ int spi_write_then_read(struct spi_device *spi, } /* ... unless someone else is using the pre-allocated buffer */ - if (down_trylock(&lock)) { + if (!mutex_trylock(&lock)) { local_buf = kmalloc(SPI_BUFSIZ, GFP_KERNEL); if (!local_buf) return -ENOMEM; @@ -628,13 +627,11 @@ int spi_write_then_read(struct spi_device *spi, /* do the i/o */ status = spi_sync(spi, &message); - if (status == 0) { + if (status == 0) memcpy(rxbuf, x[1].rx_buf, n_rx); - status = message.status; - } if (x[0].tx_buf == buf) - up(&lock); + mutex_unlock(&lock); else kfree(local_buf); diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c index 2ef11bb70b2e..22697b812205 100644 --- a/drivers/spi/spi_bfin5xx.c +++ b/drivers/spi/spi_bfin5xx.c @@ -1,17 +1,22 @@ /* - * File: drivers/spi/bfin5xx_spi.c - * Based on: N/A - * Author: Luke Yang (Analog Devices Inc.) + * File: drivers/spi/bfin5xx_spi.c + * Maintainer: + * Bryan Wu <bryan.wu@analog.com> + * Original Author: + * Luke Yang (Analog Devices Inc.) * - * Created: March. 10th 2006 - * Description: SPI controller driver for Blackfin 5xx - * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * Created: March. 10th 2006 + * Description: SPI controller driver for Blackfin BF5xx + * Bugs: Enter bugs at http://blackfin.uclinux.org/ * * Modified: * March 10, 2006 bfin5xx_spi.c Created. (Luke Yang) * August 7, 2006 added full duplex mode (Axel Weiss & Luke Yang) + * July 17, 2007 add support for BF54x SPI0 controller (Bryan Wu) + * July 30, 2007 add platfrom_resource interface to support multi-port + * SPI controller (Bryan Wu) * - * Copyright 2004-2006 Analog Devices Inc. + * Copyright 2004-2007 Analog Devices Inc. * * This program is free software ; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -31,50 +36,39 @@ #include <linux/init.h> #include <linux/module.h> +#include <linux/delay.h> #include <linux/device.h> +#include <linux/io.h> #include <linux/ioport.h> +#include <linux/irq.h> #include <linux/errno.h> #include <linux/interrupt.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/spi/spi.h> #include <linux/workqueue.h> -#include <linux/delay.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/delay.h> #include <asm/dma.h> - +#include <asm/portmux.h> #include <asm/bfin5xx_spi.h> -MODULE_AUTHOR("Luke Yang"); -MODULE_DESCRIPTION("Blackfin 5xx SPI Contoller"); -MODULE_LICENSE("GPL"); +#define DRV_NAME "bfin-spi" +#define DRV_AUTHOR "Bryan Wu, Luke Yang" +#define DRV_DESC "Blackfin BF5xx on-chip SPI Contoller Driver" +#define DRV_VERSION "1.0" -#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0) +MODULE_AUTHOR(DRV_AUTHOR); +MODULE_DESCRIPTION(DRV_DESC); +MODULE_LICENSE("GPL"); -#define DEFINE_SPI_REG(reg, off) \ -static inline u16 read_##reg(void) \ - { return *(volatile unsigned short*)(SPI0_REGBASE + off); } \ -static inline void write_##reg(u16 v) \ - {*(volatile unsigned short*)(SPI0_REGBASE + off) = v;\ - SSYNC();} +#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07) == 0) -DEFINE_SPI_REG(CTRL, 0x00) -DEFINE_SPI_REG(FLAG, 0x04) -DEFINE_SPI_REG(STAT, 0x08) -DEFINE_SPI_REG(TDBR, 0x0C) -DEFINE_SPI_REG(RDBR, 0x10) -DEFINE_SPI_REG(BAUD, 0x14) -DEFINE_SPI_REG(SHAW, 0x18) -#define START_STATE ((void*)0) -#define RUNNING_STATE ((void*)1) -#define DONE_STATE ((void*)2) -#define ERROR_STATE ((void*)-1) -#define QUEUE_RUNNING 0 -#define QUEUE_STOPPED 1 -int dma_requested; +#define START_STATE ((void *)0) +#define RUNNING_STATE ((void *)1) +#define DONE_STATE ((void *)2) +#define ERROR_STATE ((void *)-1) +#define QUEUE_RUNNING 0 +#define QUEUE_STOPPED 1 struct driver_data { /* Driver model hookup */ @@ -83,6 +77,12 @@ struct driver_data { /* SPI framework hookup */ struct spi_master *master; + /* Regs base of SPI controller */ + void __iomem *regs_base; + + /* Pin request list */ + u16 *pin_req; + /* BFIN hookup */ struct bfin5xx_spi_master *master_info; @@ -107,12 +107,18 @@ struct driver_data { void *tx_end; void *rx; void *rx_end; + + /* DMA stuffs */ + int dma_channel; int dma_mapped; + int dma_requested; dma_addr_t rx_dma; dma_addr_t tx_dma; + size_t rx_map_len; size_t tx_map_len; u8 n_bytes; + int cs_change; void (*write) (struct driver_data *); void (*read) (struct driver_data *); void (*duplex) (struct driver_data *); @@ -129,28 +135,40 @@ struct chip_data { u8 enable_dma; u8 bits_per_word; /* 8 or 16 */ u8 cs_change_per_word; - u8 cs_chg_udelay; + u16 cs_chg_udelay; /* Some devices require > 255usec delay */ void (*write) (struct driver_data *); void (*read) (struct driver_data *); void (*duplex) (struct driver_data *); }; +#define DEFINE_SPI_REG(reg, off) \ +static inline u16 read_##reg(struct driver_data *drv_data) \ + { return bfin_read16(drv_data->regs_base + off); } \ +static inline void write_##reg(struct driver_data *drv_data, u16 v) \ + { bfin_write16(drv_data->regs_base + off, v); } + +DEFINE_SPI_REG(CTRL, 0x00) +DEFINE_SPI_REG(FLAG, 0x04) +DEFINE_SPI_REG(STAT, 0x08) +DEFINE_SPI_REG(TDBR, 0x0C) +DEFINE_SPI_REG(RDBR, 0x10) +DEFINE_SPI_REG(BAUD, 0x14) +DEFINE_SPI_REG(SHAW, 0x18) + static void bfin_spi_enable(struct driver_data *drv_data) { u16 cr; - cr = read_CTRL(); - write_CTRL(cr | BIT_CTL_ENABLE); - SSYNC(); + cr = read_CTRL(drv_data); + write_CTRL(drv_data, (cr | BIT_CTL_ENABLE)); } static void bfin_spi_disable(struct driver_data *drv_data) { u16 cr; - cr = read_CTRL(); - write_CTRL(cr & (~BIT_CTL_ENABLE)); - SSYNC(); + cr = read_CTRL(drv_data); + write_CTRL(drv_data, (cr & (~BIT_CTL_ENABLE))); } /* Caculate the SPI_BAUD register value based on input HZ */ @@ -170,83 +188,71 @@ static int flush(struct driver_data *drv_data) unsigned long limit = loops_per_jiffy << 1; /* wait for stop and clear stat */ - while (!(read_STAT() & BIT_STAT_SPIF) && limit--) - continue; + while (!(read_STAT(drv_data) & BIT_STAT_SPIF) && limit--) + cpu_relax(); - write_STAT(BIT_STAT_CLR); + write_STAT(drv_data, BIT_STAT_CLR); return limit; } +/* Chip select operation functions for cs_change flag */ +static void cs_active(struct driver_data *drv_data, struct chip_data *chip) +{ + u16 flag = read_FLAG(drv_data); + + flag |= chip->flag; + flag &= ~(chip->flag << 8); + + write_FLAG(drv_data, flag); +} + +static void cs_deactive(struct driver_data *drv_data, struct chip_data *chip) +{ + u16 flag = read_FLAG(drv_data); + + flag |= (chip->flag << 8); + + write_FLAG(drv_data, flag); + + /* Move delay here for consistency */ + if (chip->cs_chg_udelay) + udelay(chip->cs_chg_udelay); +} + +#define MAX_SPI_SSEL 7 + /* stop controller and re-config current chip*/ -static void restore_state(struct driver_data *drv_data) +static int restore_state(struct driver_data *drv_data) { struct chip_data *chip = drv_data->cur_chip; + int ret = 0; /* Clear status and disable clock */ - write_STAT(BIT_STAT_CLR); + write_STAT(drv_data, BIT_STAT_CLR); bfin_spi_disable(drv_data); dev_dbg(&drv_data->pdev->dev, "restoring spi ctl state\n"); -#if defined(CONFIG_BF534) || defined(CONFIG_BF536) || defined(CONFIG_BF537) - dev_dbg(&drv_data->pdev->dev, - "chip select number is %d\n", chip->chip_select_num); - - switch (chip->chip_select_num) { - case 1: - bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3c00); - SSYNC(); - break; - - case 2: - case 3: - bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PJSE_SPI); - SSYNC(); - bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3800); - SSYNC(); - break; - - case 4: - bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PFS4E_SPI); - SSYNC(); - bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3840); - SSYNC(); - break; + /* Load the registers */ + write_CTRL(drv_data, chip->ctl_reg); + write_BAUD(drv_data, chip->baud); - case 5: - bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PFS5E_SPI); - SSYNC(); - bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3820); - SSYNC(); - break; + bfin_spi_enable(drv_data); + cs_active(drv_data, chip); - case 6: - bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PFS6E_SPI); - SSYNC(); - bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3810); - SSYNC(); - break; + if (ret) + dev_dbg(&drv_data->pdev->dev, + ": request chip select number %d failed\n", + chip->chip_select_num); - case 7: - bfin_write_PORT_MUX(bfin_read_PORT_MUX() | PJCE_SPI); - SSYNC(); - bfin_write_PORTF_FER(bfin_read_PORTF_FER() | 0x3800); - SSYNC(); - break; - } -#endif - - /* Load the registers */ - write_CTRL(chip->ctl_reg); - write_BAUD(chip->baud); - write_FLAG(chip->flag); + return ret; } /* used to kick off transfer in rx mode */ -static unsigned short dummy_read(void) +static unsigned short dummy_read(struct driver_data *drv_data) { unsigned short tmp; - tmp = read_RDBR(); + tmp = read_RDBR(drv_data); return tmp; } @@ -255,9 +261,9 @@ static void null_writer(struct driver_data *drv_data) u8 n_bytes = drv_data->n_bytes; while (drv_data->tx < drv_data->tx_end) { - write_TDBR(0); - while ((read_STAT() & BIT_STAT_TXS)) - continue; + write_TDBR(drv_data, 0); + while ((read_STAT(drv_data) & BIT_STAT_TXS)) + cpu_relax(); drv_data->tx += n_bytes; } } @@ -265,75 +271,78 @@ static void null_writer(struct driver_data *drv_data) static void null_reader(struct driver_data *drv_data) { u8 n_bytes = drv_data->n_bytes; - dummy_read(); + dummy_read(drv_data); while (drv_data->rx < drv_data->rx_end) { - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - dummy_read(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + dummy_read(drv_data); drv_data->rx += n_bytes; } } static void u8_writer(struct driver_data *drv_data) { - dev_dbg(&drv_data->pdev->dev, - "cr8-s is 0x%x\n", read_STAT()); + dev_dbg(&drv_data->pdev->dev, + "cr8-s is 0x%x\n", read_STAT(drv_data)); + + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + while (drv_data->tx < drv_data->tx_end) { - write_TDBR(*(u8 *) (drv_data->tx)); - while (read_STAT() & BIT_STAT_TXS) - continue; + write_TDBR(drv_data, (*(u8 *) (drv_data->tx))); + while (read_STAT(drv_data) & BIT_STAT_TXS) + cpu_relax(); ++drv_data->tx; } - - /* poll for SPI completion before returning */ - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; } static void u8_cs_chg_writer(struct driver_data *drv_data) { struct chip_data *chip = drv_data->cur_chip; + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + while (drv_data->tx < drv_data->tx_end) { - write_FLAG(chip->flag); - SSYNC(); - - write_TDBR(*(u8 *) (drv_data->tx)); - while (read_STAT() & BIT_STAT_TXS) - continue; - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - write_FLAG(0xFF00 | chip->flag); - SSYNC(); - if (chip->cs_chg_udelay) - udelay(chip->cs_chg_udelay); + cs_active(drv_data, chip); + + write_TDBR(drv_data, (*(u8 *) (drv_data->tx))); + while (read_STAT(drv_data) & BIT_STAT_TXS) + cpu_relax(); + + cs_deactive(drv_data, chip); + ++drv_data->tx; } - write_FLAG(0xFF00); - SSYNC(); } static void u8_reader(struct driver_data *drv_data) { - dev_dbg(&drv_data->pdev->dev, - "cr-8 is 0x%x\n", read_STAT()); + dev_dbg(&drv_data->pdev->dev, + "cr-8 is 0x%x\n", read_STAT(drv_data)); + + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); /* clear TDBR buffer before read(else it will be shifted out) */ - write_TDBR(0xFFFF); + write_TDBR(drv_data, 0xFFFF); - dummy_read(); + dummy_read(drv_data); while (drv_data->rx < drv_data->rx_end - 1) { - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u8 *) (drv_data->rx) = read_RDBR(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u8 *) (drv_data->rx) = read_RDBR(drv_data); ++drv_data->rx; } - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u8 *) (drv_data->rx) = read_SHAW(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u8 *) (drv_data->rx) = read_SHAW(drv_data); ++drv_data->rx; } @@ -341,36 +350,47 @@ static void u8_cs_chg_reader(struct driver_data *drv_data) { struct chip_data *chip = drv_data->cur_chip; - while (drv_data->rx < drv_data->rx_end) { - write_FLAG(chip->flag); - SSYNC(); - - read_RDBR(); /* kick off */ - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - *(u8 *) (drv_data->rx) = read_SHAW(); - write_FLAG(0xFF00 | chip->flag); - SSYNC(); - if (chip->cs_chg_udelay) - udelay(chip->cs_chg_udelay); + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + + /* clear TDBR buffer before read(else it will be shifted out) */ + write_TDBR(drv_data, 0xFFFF); + + cs_active(drv_data, chip); + dummy_read(drv_data); + + while (drv_data->rx < drv_data->rx_end - 1) { + cs_deactive(drv_data, chip); + + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + cs_active(drv_data, chip); + *(u8 *) (drv_data->rx) = read_RDBR(drv_data); ++drv_data->rx; } - write_FLAG(0xFF00); - SSYNC(); + cs_deactive(drv_data, chip); + + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u8 *) (drv_data->rx) = read_SHAW(drv_data); + ++drv_data->rx; } static void u8_duplex(struct driver_data *drv_data) { + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + /* in duplex mode, clk is triggered by writing of TDBR */ while (drv_data->rx < drv_data->rx_end) { - write_TDBR(*(u8 *) (drv_data->tx)); - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u8 *) (drv_data->rx) = read_RDBR(); + write_TDBR(drv_data, (*(u8 *) (drv_data->tx))); + while (read_STAT(drv_data) & BIT_STAT_TXS) + cpu_relax(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u8 *) (drv_data->rx) = read_RDBR(drv_data); ++drv_data->rx; ++drv_data->tx; } @@ -380,83 +400,89 @@ static void u8_cs_chg_duplex(struct driver_data *drv_data) { struct chip_data *chip = drv_data->cur_chip; + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + while (drv_data->rx < drv_data->rx_end) { - write_FLAG(chip->flag); - SSYNC(); - - write_TDBR(*(u8 *) (drv_data->tx)); - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u8 *) (drv_data->rx) = read_RDBR(); - write_FLAG(0xFF00 | chip->flag); - SSYNC(); - if (chip->cs_chg_udelay) - udelay(chip->cs_chg_udelay); + cs_active(drv_data, chip); + + write_TDBR(drv_data, (*(u8 *) (drv_data->tx))); + while (read_STAT(drv_data) & BIT_STAT_TXS) + cpu_relax(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u8 *) (drv_data->rx) = read_RDBR(drv_data); + + cs_deactive(drv_data, chip); + ++drv_data->rx; ++drv_data->tx; } - write_FLAG(0xFF00); - SSYNC(); } static void u16_writer(struct driver_data *drv_data) { - dev_dbg(&drv_data->pdev->dev, - "cr16 is 0x%x\n", read_STAT()); + dev_dbg(&drv_data->pdev->dev, + "cr16 is 0x%x\n", read_STAT(drv_data)); + + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); while (drv_data->tx < drv_data->tx_end) { - write_TDBR(*(u16 *) (drv_data->tx)); - while ((read_STAT() & BIT_STAT_TXS)) - continue; + write_TDBR(drv_data, (*(u16 *) (drv_data->tx))); + while ((read_STAT(drv_data) & BIT_STAT_TXS)) + cpu_relax(); drv_data->tx += 2; } - - /* poll for SPI completion before returning */ - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; } static void u16_cs_chg_writer(struct driver_data *drv_data) { struct chip_data *chip = drv_data->cur_chip; + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + while (drv_data->tx < drv_data->tx_end) { - write_FLAG(chip->flag); - SSYNC(); - - write_TDBR(*(u16 *) (drv_data->tx)); - while ((read_STAT() & BIT_STAT_TXS)) - continue; - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - write_FLAG(0xFF00 | chip->flag); - SSYNC(); - if (chip->cs_chg_udelay) - udelay(chip->cs_chg_udelay); + cs_active(drv_data, chip); + + write_TDBR(drv_data, (*(u16 *) (drv_data->tx))); + while ((read_STAT(drv_data) & BIT_STAT_TXS)) + cpu_relax(); + + cs_deactive(drv_data, chip); + drv_data->tx += 2; } - write_FLAG(0xFF00); - SSYNC(); } static void u16_reader(struct driver_data *drv_data) { dev_dbg(&drv_data->pdev->dev, - "cr-16 is 0x%x\n", read_STAT()); - dummy_read(); + "cr-16 is 0x%x\n", read_STAT(drv_data)); + + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + + /* clear TDBR buffer before read(else it will be shifted out) */ + write_TDBR(drv_data, 0xFFFF); + + dummy_read(drv_data); while (drv_data->rx < (drv_data->rx_end - 2)) { - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u16 *) (drv_data->rx) = read_RDBR(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u16 *) (drv_data->rx) = read_RDBR(drv_data); drv_data->rx += 2; } - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u16 *) (drv_data->rx) = read_SHAW(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u16 *) (drv_data->rx) = read_SHAW(drv_data); drv_data->rx += 2; } @@ -464,36 +490,47 @@ static void u16_cs_chg_reader(struct driver_data *drv_data) { struct chip_data *chip = drv_data->cur_chip; - while (drv_data->rx < drv_data->rx_end) { - write_FLAG(chip->flag); - SSYNC(); - - read_RDBR(); /* kick off */ - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - *(u16 *) (drv_data->rx) = read_SHAW(); - write_FLAG(0xFF00 | chip->flag); - SSYNC(); - if (chip->cs_chg_udelay) - udelay(chip->cs_chg_udelay); + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + + /* clear TDBR buffer before read(else it will be shifted out) */ + write_TDBR(drv_data, 0xFFFF); + + cs_active(drv_data, chip); + dummy_read(drv_data); + + while (drv_data->rx < drv_data->rx_end - 2) { + cs_deactive(drv_data, chip); + + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + cs_active(drv_data, chip); + *(u16 *) (drv_data->rx) = read_RDBR(drv_data); drv_data->rx += 2; } - write_FLAG(0xFF00); - SSYNC(); + cs_deactive(drv_data, chip); + + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u16 *) (drv_data->rx) = read_SHAW(drv_data); + drv_data->rx += 2; } static void u16_duplex(struct driver_data *drv_data) { + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + /* in duplex mode, clk is triggered by writing of TDBR */ while (drv_data->tx < drv_data->tx_end) { - write_TDBR(*(u16 *) (drv_data->tx)); - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u16 *) (drv_data->rx) = read_RDBR(); + write_TDBR(drv_data, (*(u16 *) (drv_data->tx))); + while (read_STAT(drv_data) & BIT_STAT_TXS) + cpu_relax(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u16 *) (drv_data->rx) = read_RDBR(drv_data); drv_data->rx += 2; drv_data->tx += 2; } @@ -503,25 +540,25 @@ static void u16_cs_chg_duplex(struct driver_data *drv_data) { struct chip_data *chip = drv_data->cur_chip; + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); + while (drv_data->tx < drv_data->tx_end) { - write_FLAG(chip->flag); - SSYNC(); - - write_TDBR(*(u16 *) (drv_data->tx)); - while (!(read_STAT() & BIT_STAT_SPIF)) - continue; - while (!(read_STAT() & BIT_STAT_RXS)) - continue; - *(u16 *) (drv_data->rx) = read_RDBR(); - write_FLAG(0xFF00 | chip->flag); - SSYNC(); - if (chip->cs_chg_udelay) - udelay(chip->cs_chg_udelay); + cs_active(drv_data, chip); + + write_TDBR(drv_data, (*(u16 *) (drv_data->tx))); + while (read_STAT(drv_data) & BIT_STAT_TXS) + cpu_relax(); + while (!(read_STAT(drv_data) & BIT_STAT_RXS)) + cpu_relax(); + *(u16 *) (drv_data->rx) = read_RDBR(drv_data); + + cs_deactive(drv_data, chip); + drv_data->rx += 2; drv_data->tx += 2; } - write_FLAG(0xFF00); - SSYNC(); } /* test if ther is more transfer to be done */ @@ -546,6 +583,7 @@ static void *next_transfer(struct driver_data *drv_data) */ static void giveback(struct driver_data *drv_data) { + struct chip_data *chip = drv_data->cur_chip; struct spi_transfer *last_transfer; unsigned long flags; struct spi_message *msg; @@ -565,10 +603,13 @@ static void giveback(struct driver_data *drv_data) /* disable chip select signal. And not stop spi in autobuffer mode */ if (drv_data->tx_dma != 0xFFFF) { - write_FLAG(0xFF00); + cs_deactive(drv_data, chip); bfin_spi_disable(drv_data); } + if (!drv_data->cs_change) + cs_deactive(drv_data, chip); + if (msg->complete) msg->complete(msg->context); } @@ -576,14 +617,15 @@ static void giveback(struct driver_data *drv_data) static irqreturn_t dma_irq_handler(int irq, void *dev_id) { struct driver_data *drv_data = (struct driver_data *)dev_id; + struct chip_data *chip = drv_data->cur_chip; struct spi_message *msg = drv_data->cur_msg; dev_dbg(&drv_data->pdev->dev, "in dma_irq_handler\n"); - clear_dma_irqstat(CH_SPI); + clear_dma_irqstat(drv_data->dma_channel); /* Wait for DMA to complete */ - while (get_dma_curr_irqstat(CH_SPI) & DMA_RUN) - continue; + while (get_dma_curr_irqstat(drv_data->dma_channel) & DMA_RUN) + cpu_relax(); /* * wait for the last transaction shifted out. HRM states: @@ -592,18 +634,19 @@ static irqreturn_t dma_irq_handler(int irq, void *dev_id) * register until it goes low for 2 successive reads */ if (drv_data->tx != NULL) { - while ((bfin_read_SPI_STAT() & TXS) || - (bfin_read_SPI_STAT() & TXS)) - continue; + while ((read_STAT(drv_data) & TXS) || + (read_STAT(drv_data) & TXS)) + cpu_relax(); } - while (!(bfin_read_SPI_STAT() & SPIF)) - continue; - - bfin_spi_disable(drv_data); + while (!(read_STAT(drv_data) & SPIF)) + cpu_relax(); msg->actual_length += drv_data->len_in_bytes; + if (drv_data->cs_change) + cs_deactive(drv_data, chip); + /* Move to next transfer */ msg->state = next_transfer(drv_data); @@ -613,8 +656,8 @@ static irqreturn_t dma_irq_handler(int irq, void *dev_id) /* free the irq handler before next transfer */ dev_dbg(&drv_data->pdev->dev, "disable dma channel irq%d\n", - CH_SPI); - dma_disable_irq(CH_SPI); + drv_data->dma_channel); + dma_disable_irq(drv_data->dma_channel); return IRQ_HANDLED; } @@ -690,31 +733,67 @@ static void pump_transfers(unsigned long data) drv_data->rx_dma = transfer->rx_dma; drv_data->tx_dma = transfer->tx_dma; drv_data->len_in_bytes = transfer->len; + drv_data->cs_change = transfer->cs_change; + + /* Bits per word setup */ + switch (transfer->bits_per_word) { + case 8: + drv_data->n_bytes = 1; + width = CFG_SPI_WORDSIZE8; + drv_data->read = chip->cs_change_per_word ? + u8_cs_chg_reader : u8_reader; + drv_data->write = chip->cs_change_per_word ? + u8_cs_chg_writer : u8_writer; + drv_data->duplex = chip->cs_change_per_word ? + u8_cs_chg_duplex : u8_duplex; + break; + + case 16: + drv_data->n_bytes = 2; + width = CFG_SPI_WORDSIZE16; + drv_data->read = chip->cs_change_per_word ? + u16_cs_chg_reader : u16_reader; + drv_data->write = chip->cs_change_per_word ? + u16_cs_chg_writer : u16_writer; + drv_data->duplex = chip->cs_change_per_word ? + u16_cs_chg_duplex : u16_duplex; + break; + + default: + /* No change, the same as default setting */ + drv_data->n_bytes = chip->n_bytes; + width = chip->width; + drv_data->write = drv_data->tx ? chip->write : null_writer; + drv_data->read = drv_data->rx ? chip->read : null_reader; + drv_data->duplex = chip->duplex ? chip->duplex : null_writer; + break; + } + cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD)); + cr |= (width << 8); + write_CTRL(drv_data, cr); - width = chip->width; if (width == CFG_SPI_WORDSIZE16) { drv_data->len = (transfer->len) >> 1; } else { drv_data->len = transfer->len; } - drv_data->write = drv_data->tx ? chip->write : null_writer; - drv_data->read = drv_data->rx ? chip->read : null_reader; - drv_data->duplex = chip->duplex ? chip->duplex : null_writer; - dev_dbg(&drv_data->pdev->dev, - "transfer: drv_data->write is %p, chip->write is %p, null_wr is %p\n", - drv_data->write, chip->write, null_writer); + dev_dbg(&drv_data->pdev->dev, "transfer: ", + "drv_data->write is %p, chip->write is %p, null_wr is %p\n", + drv_data->write, chip->write, null_writer); /* speed and width has been set on per message */ message->state = RUNNING_STATE; dma_config = 0; - /* restore spi status for each spi transfer */ - if (transfer->speed_hz) { - write_BAUD(hz_to_spi_baud(transfer->speed_hz)); - } else { - write_BAUD(chip->baud); - } - write_FLAG(chip->flag); + /* Speed setup (surely valid because already checked) */ + if (transfer->speed_hz) + write_BAUD(drv_data, hz_to_spi_baud(transfer->speed_hz)); + else + write_BAUD(drv_data, chip->baud); + + write_STAT(drv_data, BIT_STAT_CLR); + cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD)); + cs_active(drv_data, chip); dev_dbg(&drv_data->pdev->dev, "now pumping a transfer: width is %d, len is %d\n", @@ -727,25 +806,25 @@ static void pump_transfers(unsigned long data) */ if (drv_data->cur_chip->enable_dma && drv_data->len > 6) { - write_STAT(BIT_STAT_CLR); - disable_dma(CH_SPI); - clear_dma_irqstat(CH_SPI); + disable_dma(drv_data->dma_channel); + clear_dma_irqstat(drv_data->dma_channel); bfin_spi_disable(drv_data); /* config dma channel */ dev_dbg(&drv_data->pdev->dev, "doing dma transfer\n"); if (width == CFG_SPI_WORDSIZE16) { - set_dma_x_count(CH_SPI, drv_data->len); - set_dma_x_modify(CH_SPI, 2); + set_dma_x_count(drv_data->dma_channel, drv_data->len); + set_dma_x_modify(drv_data->dma_channel, 2); dma_width = WDSIZE_16; } else { - set_dma_x_count(CH_SPI, drv_data->len); - set_dma_x_modify(CH_SPI, 1); + set_dma_x_count(drv_data->dma_channel, drv_data->len); + set_dma_x_modify(drv_data->dma_channel, 1); dma_width = WDSIZE_8; } - /* set transfer width,direction. And enable spi */ - cr = (read_CTRL() & (~BIT_CTL_TIMOD)); + /* poll for SPI completion before start */ + while (!(read_STAT(drv_data) & BIT_STAT_SPIF)) + cpu_relax(); /* dirty hack for autobuffer DMA mode */ if (drv_data->tx_dma == 0xFFFF) { @@ -755,13 +834,18 @@ static void pump_transfers(unsigned long data) /* no irq in autobuffer mode */ dma_config = (DMAFLOW_AUTO | RESTART | dma_width | DI_EN); - set_dma_config(CH_SPI, dma_config); - set_dma_start_addr(CH_SPI, (unsigned long)drv_data->tx); - enable_dma(CH_SPI); - write_CTRL(cr | CFG_SPI_DMAWRITE | (width << 8) | - (CFG_SPI_ENABLE << 14)); - - /* just return here, there can only be one transfer in this mode */ + set_dma_config(drv_data->dma_channel, dma_config); + set_dma_start_addr(drv_data->dma_channel, + (unsigned long)drv_data->tx); + enable_dma(drv_data->dma_channel); + + /* start SPI transfer */ + write_CTRL(drv_data, + (cr | CFG_SPI_DMAWRITE | BIT_CTL_ENABLE)); + + /* just return here, there can only be one transfer + * in this mode + */ message->status = 0; giveback(drv_data); return; @@ -772,58 +856,51 @@ static void pump_transfers(unsigned long data) /* set transfer mode, and enable SPI */ dev_dbg(&drv_data->pdev->dev, "doing DMA in.\n"); - /* disable SPI before write to TDBR */ - write_CTRL(cr & ~BIT_CTL_ENABLE); - /* clear tx reg soformer data is not shifted out */ - write_TDBR(0xFF); + write_TDBR(drv_data, 0xFFFF); - set_dma_x_count(CH_SPI, drv_data->len); + set_dma_x_count(drv_data->dma_channel, drv_data->len); /* start dma */ - dma_enable_irq(CH_SPI); + dma_enable_irq(drv_data->dma_channel); dma_config = (WNR | RESTART | dma_width | DI_EN); - set_dma_config(CH_SPI, dma_config); - set_dma_start_addr(CH_SPI, (unsigned long)drv_data->rx); - enable_dma(CH_SPI); + set_dma_config(drv_data->dma_channel, dma_config); + set_dma_start_addr(drv_data->dma_channel, + (unsigned long)drv_data->rx); + enable_dma(drv_data->dma_channel); + + /* start SPI transfer */ + write_CTRL(drv_data, + (cr | CFG_SPI_DMAREAD | BIT_CTL_ENABLE)); - cr |= - CFG_SPI_DMAREAD | (width << 8) | (CFG_SPI_ENABLE << - 14); - /* set transfer mode, and enable SPI */ - write_CTRL(cr); } else if (drv_data->tx != NULL) { dev_dbg(&drv_data->pdev->dev, "doing DMA out.\n"); /* start dma */ - dma_enable_irq(CH_SPI); + dma_enable_irq(drv_data->dma_channel); dma_config = (RESTART | dma_width | DI_EN); - set_dma_config(CH_SPI, dma_config); - set_dma_start_addr(CH_SPI, (unsigned long)drv_data->tx); - enable_dma(CH_SPI); - - write_CTRL(cr | CFG_SPI_DMAWRITE | (width << 8) | - (CFG_SPI_ENABLE << 14)); - + set_dma_config(drv_data->dma_channel, dma_config); + set_dma_start_addr(drv_data->dma_channel, + (unsigned long)drv_data->tx); + enable_dma(drv_data->dma_channel); + + /* start SPI transfer */ + write_CTRL(drv_data, + (cr | CFG_SPI_DMAWRITE | BIT_CTL_ENABLE)); } } else { /* IO mode write then read */ dev_dbg(&drv_data->pdev->dev, "doing IO transfer\n"); - write_STAT(BIT_STAT_CLR); - if (drv_data->tx != NULL && drv_data->rx != NULL) { /* full duplex mode */ BUG_ON((drv_data->tx_end - drv_data->tx) != (drv_data->rx_end - drv_data->rx)); - cr = (read_CTRL() & (~BIT_CTL_TIMOD)); - cr |= CFG_SPI_WRITE | (width << 8) | - (CFG_SPI_ENABLE << 14); dev_dbg(&drv_data->pdev->dev, "IO duplex: cr is 0x%x\n", cr); - write_CTRL(cr); - SSYNC(); + /* set SPI transfer mode */ + write_CTRL(drv_data, (cr | CFG_SPI_WRITE)); drv_data->duplex(drv_data); @@ -831,14 +908,11 @@ static void pump_transfers(unsigned long data) tranf_success = 0; } else if (drv_data->tx != NULL) { /* write only half duplex */ - cr = (read_CTRL() & (~BIT_CTL_TIMOD)); - cr |= CFG_SPI_WRITE | (width << 8) | - (CFG_SPI_ENABLE << 14); - dev_dbg(&drv_data->pdev->dev, + dev_dbg(&drv_data->pdev->dev, "IO write: cr is 0x%x\n", cr); - write_CTRL(cr); - SSYNC(); + /* set SPI transfer mode */ + write_CTRL(drv_data, (cr | CFG_SPI_WRITE)); drv_data->write(drv_data); @@ -846,14 +920,11 @@ static void pump_transfers(unsigned long data) tranf_success = 0; } else if (drv_data->rx != NULL) { /* read only half duplex */ - cr = (read_CTRL() & (~BIT_CTL_TIMOD)); - cr |= CFG_SPI_READ | (width << 8) | - (CFG_SPI_ENABLE << 14); - dev_dbg(&drv_data->pdev->dev, + dev_dbg(&drv_data->pdev->dev, "IO read: cr is 0x%x\n", cr); - write_CTRL(cr); - SSYNC(); + /* set SPI transfer mode */ + write_CTRL(drv_data, (cr | CFG_SPI_READ)); drv_data->read(drv_data); if (drv_data->rx != drv_data->rx_end) @@ -861,7 +932,7 @@ static void pump_transfers(unsigned long data) } if (!tranf_success) { - dev_dbg(&drv_data->pdev->dev, + dev_dbg(&drv_data->pdev->dev, "IO write error!\n"); message->state = ERROR_STATE; } else { @@ -881,9 +952,11 @@ static void pump_transfers(unsigned long data) /* pop a msg from queue and kick off real transfer */ static void pump_messages(struct work_struct *work) { - struct driver_data *drv_data = container_of(work, struct driver_data, pump_messages); + struct driver_data *drv_data; unsigned long flags; + drv_data = container_of(work, struct driver_data, pump_messages); + /* Lock queue and check for queue work */ spin_lock_irqsave(&drv_data->lock, flags); if (list_empty(&drv_data->queue) || drv_data->run == QUEUE_STOPPED) { @@ -902,6 +975,14 @@ static void pump_messages(struct work_struct *work) /* Extract head of queue */ drv_data->cur_msg = list_entry(drv_data->queue.next, struct spi_message, queue); + + /* Setup the SSP using the per chip configuration */ + drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi); + if (restore_state(drv_data)) { + spin_unlock_irqrestore(&drv_data->lock, flags); + return; + }; + list_del_init(&drv_data->cur_msg->queue); /* Initial message state */ @@ -909,15 +990,12 @@ static void pump_messages(struct work_struct *work) drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next, struct spi_transfer, transfer_list); - /* Setup the SSP using the per chip configuration */ - drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi); - restore_state(drv_data); + dev_dbg(&drv_data->pdev->dev, "got a message to pump, " + "state is set to: baud %d, flag 0x%x, ctl 0x%x\n", + drv_data->cur_chip->baud, drv_data->cur_chip->flag, + drv_data->cur_chip->ctl_reg); + dev_dbg(&drv_data->pdev->dev, - "got a message to pump, state is set to: baud %d, flag 0x%x, ctl 0x%x\n", - drv_data->cur_chip->baud, drv_data->cur_chip->flag, - drv_data->cur_chip->ctl_reg); - - dev_dbg(&drv_data->pdev->dev, "the first transfer len is %d\n", drv_data->cur_transfer->len); @@ -959,6 +1037,22 @@ static int transfer(struct spi_device *spi, struct spi_message *msg) return 0; } +#define MAX_SPI_SSEL 7 + +static u16 ssel[3][MAX_SPI_SSEL] = { + {P_SPI0_SSEL1, P_SPI0_SSEL2, P_SPI0_SSEL3, + P_SPI0_SSEL4, P_SPI0_SSEL5, + P_SPI0_SSEL6, P_SPI0_SSEL7}, + + {P_SPI1_SSEL1, P_SPI1_SSEL2, P_SPI1_SSEL3, + P_SPI1_SSEL4, P_SPI1_SSEL5, + P_SPI1_SSEL6, P_SPI1_SSEL7}, + + {P_SPI2_SSEL1, P_SPI2_SSEL2, P_SPI2_SSEL3, + P_SPI2_SSEL4, P_SPI2_SSEL5, + P_SPI2_SSEL6, P_SPI2_SSEL7}, +}; + /* first setup for new devices */ static int setup(struct spi_device *spi) { @@ -993,6 +1087,18 @@ static int setup(struct spi_device *spi) /* chip_info isn't always needed */ if (chip_info) { + /* Make sure people stop trying to set fields via ctl_reg + * when they should actually be using common SPI framework. + * Currently we let through: WOM EMISO PSSE GM SZ TIMOD. + * Not sure if a user actually needs/uses any of these, + * but let's assume (for now) they do. + */ + if (chip_info->ctl_reg & (SPE|MSTR|CPOL|CPHA|LSBF|SIZE)) { + dev_err(&spi->dev, "do not set bits in ctl_reg " + "that the SPI framework manages\n"); + return -EINVAL; + } + chip->enable_dma = chip_info->enable_dma != 0 && drv_data->master_info->enable_dma; chip->ctl_reg = chip_info->ctl_reg; @@ -1015,20 +1121,20 @@ static int setup(struct spi_device *spi) * if any one SPI chip is registered and wants DMA, request the * DMA channel for it */ - if (chip->enable_dma && !dma_requested) { + if (chip->enable_dma && !drv_data->dma_requested) { /* register dma irq handler */ - if (request_dma(CH_SPI, "BF53x_SPI_DMA") < 0) { + if (request_dma(drv_data->dma_channel, "BF53x_SPI_DMA") < 0) { dev_dbg(&spi->dev, "Unable to request BlackFin SPI DMA channel\n"); return -ENODEV; } - if (set_dma_callback(CH_SPI, (void *)dma_irq_handler, drv_data) - < 0) { + if (set_dma_callback(drv_data->dma_channel, + (void *)dma_irq_handler, drv_data) < 0) { dev_dbg(&spi->dev, "Unable to set dma callback\n"); return -EPERM; } - dma_disable_irq(CH_SPI); - dma_requested = 1; + dma_disable_irq(drv_data->dma_channel); + drv_data->dma_requested = 1; } /* @@ -1077,6 +1183,14 @@ static int setup(struct spi_device *spi) spi_set_ctldata(spi, chip); + dev_dbg(&spi->dev, "chip select number is %d\n", chip->chip_select_num); + if ((chip->chip_select_num > 0) + && (chip->chip_select_num <= spi->master->num_chipselect)) + peripheral_request(ssel[spi->master->bus_num] + [chip->chip_select_num-1], DRV_NAME); + + cs_deactive(drv_data, chip); + return 0; } @@ -1088,6 +1202,11 @@ static void cleanup(struct spi_device *spi) { struct chip_data *chip = spi_get_ctldata(spi); + if ((chip->chip_select_num > 0) + && (chip->chip_select_num <= spi->master->num_chipselect)) + peripheral_free(ssel[spi->master->bus_num] + [chip->chip_select_num-1]); + kfree(chip); } @@ -1183,6 +1302,7 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev) struct bfin5xx_spi_master *platform_info; struct spi_master *master; struct driver_data *drv_data = 0; + struct resource *res; int status = 0; platform_info = dev->platform_data; @@ -1193,10 +1313,12 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev) dev_err(&pdev->dev, "can not alloc spi_master\n"); return -ENOMEM; } + drv_data = spi_master_get_devdata(master); drv_data->master = master; drv_data->master_info = platform_info; drv_data->pdev = pdev; + drv_data->pin_req = platform_info->pin_req; master->bus_num = pdev->id; master->num_chipselect = platform_info->num_chipselect; @@ -1204,15 +1326,38 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev) master->setup = setup; master->transfer = transfer; + /* Find and map our resources */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (res == NULL) { + dev_err(dev, "Cannot get IORESOURCE_MEM\n"); + status = -ENOENT; + goto out_error_get_res; + } + + drv_data->regs_base = ioremap(res->start, (res->end - res->start + 1)); + if (drv_data->regs_base == NULL) { + dev_err(dev, "Cannot map IO\n"); + status = -ENXIO; + goto out_error_ioremap; + } + + drv_data->dma_channel = platform_get_irq(pdev, 0); + if (drv_data->dma_channel < 0) { + dev_err(dev, "No DMA channel specified\n"); + status = -ENOENT; + goto out_error_no_dma_ch; + } + /* Initial and start queue */ status = init_queue(drv_data); if (status != 0) { - dev_err(&pdev->dev, "problem initializing queue\n"); + dev_err(dev, "problem initializing queue\n"); goto out_error_queue_alloc; } + status = start_queue(drv_data); if (status != 0) { - dev_err(&pdev->dev, "problem starting queue\n"); + dev_err(dev, "problem starting queue\n"); goto out_error_queue_alloc; } @@ -1220,15 +1365,30 @@ static int __init bfin5xx_spi_probe(struct platform_device *pdev) platform_set_drvdata(pdev, drv_data); status = spi_register_master(master); if (status != 0) { - dev_err(&pdev->dev, "problem registering spi master\n"); + dev_err(dev, "problem registering spi master\n"); goto out_error_queue_alloc; } - dev_dbg(&pdev->dev, "controller probe successfully\n"); + + status = peripheral_request_list(drv_data->pin_req, DRV_NAME); + if (status != 0) { + dev_err(&pdev->dev, ": Requesting Peripherals failed\n"); + goto out_error; + } + + dev_info(dev, "%s, Version %s, regs_base@%p, dma channel@%d\n", + DRV_DESC, DRV_VERSION, drv_data->regs_base, + drv_data->dma_channel); return status; - out_error_queue_alloc: +out_error_queue_alloc: destroy_queue(drv_data); +out_error_no_dma_ch: + iounmap((void *) drv_data->regs_base); +out_error_ioremap: +out_error_get_res: +out_error: spi_master_put(master); + return status; } @@ -1251,13 +1411,15 @@ static int __devexit bfin5xx_spi_remove(struct platform_device *pdev) /* Release DMA */ if (drv_data->master_info->enable_dma) { - if (dma_channel_active(CH_SPI)) - free_dma(CH_SPI); + if (dma_channel_active(drv_data->dma_channel)) + free_dma(drv_data->dma_channel); } /* Disconnect from the SPI framework */ spi_unregister_master(drv_data->master); + peripheral_free_list(drv_data->pin_req); + /* Prevent double remove */ platform_set_drvdata(pdev, NULL); @@ -1305,7 +1467,7 @@ static int bfin5xx_spi_resume(struct platform_device *pdev) MODULE_ALIAS("bfin-spi-master"); /* for platform bus hotplug */ static struct platform_driver bfin5xx_spi_driver = { .driver = { - .name = "bfin-spi-master", + .name = DRV_NAME, .owner = THIS_MODULE, }, .suspend = bfin5xx_spi_suspend, @@ -1161,7 +1161,12 @@ retry: ret = 0; if (to.timed_out) /* Only check after read evt */ break; - io_schedule(); + /* Try to only show up in io wait if there are ops + * in flight */ + if (ctx->reqs_active) + io_schedule(); + else + schedule(); if (signal_pending(tsk)) { ret = -EINTR; break; diff --git a/fs/bfs/inode.c b/fs/bfs/inode.c index 294c41baef6e..a64a71d444f5 100644 --- a/fs/bfs/inode.c +++ b/fs/bfs/inode.c @@ -178,7 +178,8 @@ static void bfs_delete_inode(struct inode *inode) brelse(bh); if (bi->i_dsk_ino) { - info->si_freeb += BFS_FILEBLOCKS(bi); + if (bi->i_sblock) + info->si_freeb += bi->i_eblock + 1 - bi->i_sblock; info->si_freei++; clear_bit(ino, info->si_imap); dump_imap("delete_inode", s); diff --git a/fs/cifs/cifsacl.c b/fs/cifs/cifsacl.c index f02fdef463a7..c312adcba4fc 100644 --- a/fs/cifs/cifsacl.c +++ b/fs/cifs/cifsacl.c @@ -134,9 +134,10 @@ int compare_sids(const struct cifs_sid *ctsid, const struct cifs_sid *cwsid) pmode is the existing mode (we only want to overwrite part of this bits to set can be: S_IRWXU, S_IRWXG or S_IRWXO ie 00700 or 00070 or 00007 */ -static void access_flags_to_mode(__u32 ace_flags, int type, umode_t *pmode, +static void access_flags_to_mode(__le32 ace_flags, int type, umode_t *pmode, umode_t *pbits_to_set) { + __u32 flags = le32_to_cpu(ace_flags); /* the order of ACEs is important. The canonical order is to begin with DENY entries followed by ALLOW, otherwise an allow entry could be encountered first, making the subsequent deny entry like "dead code" @@ -146,17 +147,17 @@ static void access_flags_to_mode(__u32 ace_flags, int type, umode_t *pmode, /* For deny ACEs we change the mask so that subsequent allow access control entries do not turn on the bits we are denying */ if (type == ACCESS_DENIED) { - if (ace_flags & GENERIC_ALL) { + if (flags & GENERIC_ALL) { *pbits_to_set &= ~S_IRWXUGO; } - if ((ace_flags & GENERIC_WRITE) || - ((ace_flags & FILE_WRITE_RIGHTS) == FILE_WRITE_RIGHTS)) + if ((flags & GENERIC_WRITE) || + ((flags & FILE_WRITE_RIGHTS) == FILE_WRITE_RIGHTS)) *pbits_to_set &= ~S_IWUGO; - if ((ace_flags & GENERIC_READ) || - ((ace_flags & FILE_READ_RIGHTS) == FILE_READ_RIGHTS)) + if ((flags & GENERIC_READ) || + ((flags & FILE_READ_RIGHTS) == FILE_READ_RIGHTS)) *pbits_to_set &= ~S_IRUGO; - if ((ace_flags & GENERIC_EXECUTE) || - ((ace_flags & FILE_EXEC_RIGHTS) == FILE_EXEC_RIGHTS)) + if ((flags & GENERIC_EXECUTE) || + ((flags & FILE_EXEC_RIGHTS) == FILE_EXEC_RIGHTS)) *pbits_to_set &= ~S_IXUGO; return; } else if (type != ACCESS_ALLOWED) { @@ -165,25 +166,25 @@ static void access_flags_to_mode(__u32 ace_flags, int type, umode_t *pmode, } /* else ACCESS_ALLOWED type */ - if (ace_flags & GENERIC_ALL) { + if (flags & GENERIC_ALL) { *pmode |= (S_IRWXUGO & (*pbits_to_set)); #ifdef CONFIG_CIFS_DEBUG2 cFYI(1, ("all perms")); #endif return; } - if ((ace_flags & GENERIC_WRITE) || - ((ace_flags & FILE_WRITE_RIGHTS) == FILE_WRITE_RIGHTS)) + if ((flags & GENERIC_WRITE) || + ((flags & FILE_WRITE_RIGHTS) == FILE_WRITE_RIGHTS)) *pmode |= (S_IWUGO & (*pbits_to_set)); - if ((ace_flags & GENERIC_READ) || - ((ace_flags & FILE_READ_RIGHTS) == FILE_READ_RIGHTS)) + if ((flags & GENERIC_READ) || + ((flags & FILE_READ_RIGHTS) == FILE_READ_RIGHTS)) *pmode |= (S_IRUGO & (*pbits_to_set)); - if ((ace_flags & GENERIC_EXECUTE) || - ((ace_flags & FILE_EXEC_RIGHTS) == FILE_EXEC_RIGHTS)) + if ((flags & GENERIC_EXECUTE) || + ((flags & FILE_EXEC_RIGHTS) == FILE_EXEC_RIGHTS)) *pmode |= (S_IXUGO & (*pbits_to_set)); #ifdef CONFIG_CIFS_DEBUG2 - cFYI(1, ("access flags 0x%x mode now 0x%x", ace_flags, *pmode)); + cFYI(1, ("access flags 0x%x mode now 0x%x", flags, *pmode)); #endif return; } diff --git a/fs/jbd/checkpoint.c b/fs/jbd/checkpoint.c index 47552d4a6324..0f69c416eebc 100644 --- a/fs/jbd/checkpoint.c +++ b/fs/jbd/checkpoint.c @@ -602,15 +602,15 @@ int __journal_remove_checkpoint(struct journal_head *jh) /* * There is one special case to worry about: if we have just pulled the - * buffer off a committing transaction's forget list, then even if the - * checkpoint list is empty, the transaction obviously cannot be - * dropped! + * buffer off a running or committing transaction's checkpoing list, + * then even if the checkpoint list is empty, the transaction obviously + * cannot be dropped! * - * The locking here around j_committing_transaction is a bit sleazy. + * The locking here around t_state is a bit sleazy. * See the comment at the end of journal_commit_transaction(). */ - if (transaction == journal->j_committing_transaction) { - JBUFFER_TRACE(jh, "belongs to committing transaction"); + if (transaction->t_state != T_FINISHED) { + JBUFFER_TRACE(jh, "belongs to running/committing transaction"); goto out; } diff --git a/fs/jbd/commit.c b/fs/jbd/commit.c index 8f1f2aa5fb39..610264b99a8e 100644 --- a/fs/jbd/commit.c +++ b/fs/jbd/commit.c @@ -858,10 +858,10 @@ restart_loop: } spin_unlock(&journal->j_list_lock); /* - * This is a bit sleazy. We borrow j_list_lock to protect - * journal->j_committing_transaction in __journal_remove_checkpoint. - * Really, __journal_remove_checkpoint should be using j_state_lock but - * it's a bit hassle to hold that across __journal_remove_checkpoint + * This is a bit sleazy. We use j_list_lock to protect transition + * of a transaction into T_FINISHED state and calling + * __journal_drop_transaction(). Otherwise we could race with + * other checkpointing code processing the transaction... */ spin_lock(&journal->j_state_lock); spin_lock(&journal->j_list_lock); diff --git a/fs/jffs2/background.c b/fs/jffs2/background.c index d568ae846741..8adebd3e43c6 100644 --- a/fs/jffs2/background.c +++ b/fs/jffs2/background.c @@ -105,7 +105,7 @@ static int jffs2_garbage_collect_thread(void *_c) /* Put_super will send a SIGKILL and then wait on the sem. */ - while (signal_pending(current)) { + while (signal_pending(current) || freezing(current)) { siginfo_t info; unsigned long signr; diff --git a/fs/ocfs2/cluster/tcp.c b/fs/ocfs2/cluster/tcp.c index d84bd155997b..ee50c9610e7f 100644 --- a/fs/ocfs2/cluster/tcp.c +++ b/fs/ocfs2/cluster/tcp.c @@ -72,14 +72,6 @@ #include "tcp_internal.h" -/* - * The linux network stack isn't sparse endian clean.. It has macros like - * ntohs() which perform the endian checks and structs like sockaddr_in - * which aren't annotated. So __force is found here to get the build - * clean. When they emerge from the dark ages and annotate the code - * we can remove these. - */ - #define SC_NODEF_FMT "node %s (num %u) at %u.%u.%u.%u:%u" #define SC_NODEF_ARGS(sc) sc->sc_node->nd_name, sc->sc_node->nd_num, \ NIPQUAD(sc->sc_node->nd_ipv4_address), \ @@ -1500,7 +1492,7 @@ static void o2net_start_connect(struct work_struct *work) myaddr.sin_family = AF_INET; myaddr.sin_addr.s_addr = mynode->nd_ipv4_address; - myaddr.sin_port = (__force u16)htons(0); /* any port */ + myaddr.sin_port = htons(0); /* any port */ ret = sock->ops->bind(sock, (struct sockaddr *)&myaddr, sizeof(myaddr)); @@ -1701,11 +1693,11 @@ static int o2net_accept_one(struct socket *sock) if (ret < 0) goto out; - node = o2nm_get_node_by_ip((__force __be32)sin.sin_addr.s_addr); + node = o2nm_get_node_by_ip(sin.sin_addr.s_addr); if (node == NULL) { mlog(ML_NOTICE, "attempt to connect from unknown node at " "%u.%u.%u.%u:%d\n", NIPQUAD(sin.sin_addr.s_addr), - ntohs((__force __be16)sin.sin_port)); + ntohs(sin.sin_port)); ret = -EINVAL; goto out; } @@ -1714,7 +1706,7 @@ static int o2net_accept_one(struct socket *sock) mlog(ML_NOTICE, "unexpected connect attempted from a lower " "numbered node '%s' at " "%u.%u.%u.%u:%d with num %u\n", node->nd_name, NIPQUAD(sin.sin_addr.s_addr), - ntohs((__force __be16)sin.sin_port), node->nd_num); + ntohs(sin.sin_port), node->nd_num); ret = -EINVAL; goto out; } @@ -1725,7 +1717,7 @@ static int o2net_accept_one(struct socket *sock) mlog(ML_CONN, "attempt to connect from node '%s' at " "%u.%u.%u.%u:%d but it isn't heartbeating\n", node->nd_name, NIPQUAD(sin.sin_addr.s_addr), - ntohs((__force __be16)sin.sin_port)); + ntohs(sin.sin_port)); ret = -EINVAL; goto out; } @@ -1742,7 +1734,7 @@ static int o2net_accept_one(struct socket *sock) mlog(ML_NOTICE, "attempt to connect from node '%s' at " "%u.%u.%u.%u:%d but it already has an open connection\n", node->nd_name, NIPQUAD(sin.sin_addr.s_addr), - ntohs((__force __be16)sin.sin_port)); + ntohs(sin.sin_port)); goto out; } diff --git a/fs/proc/generic.c b/fs/proc/generic.c index 39f3d6519035..8d49838e5554 100644 --- a/fs/proc/generic.c +++ b/fs/proc/generic.c @@ -374,9 +374,16 @@ static int proc_delete_dentry(struct dentry * dentry) return 1; } +static int proc_revalidate_dentry(struct dentry *dentry, struct nameidata *nd) +{ + d_drop(dentry); + return 0; +} + static struct dentry_operations proc_dentry_operations = { .d_delete = proc_delete_dentry, + .d_revalidate = proc_revalidate_dentry, }; /* @@ -397,8 +404,11 @@ struct dentry *proc_lookup(struct inode * dir, struct dentry *dentry, struct nam if (de->namelen != dentry->d_name.len) continue; if (!memcmp(dentry->d_name.name, de->name, de->namelen)) { - unsigned int ino = de->low_ino; + unsigned int ino; + if (de->shadow_proc) + de = de->shadow_proc(current, de); + ino = de->low_ino; de_get(de); spin_unlock(&proc_subdir_lock); error = -EINVAL; @@ -585,6 +595,7 @@ static struct proc_dir_entry *proc_create(struct proc_dir_entry **parent, ent->namelen = len; ent->mode = mode; ent->nlink = nlink; + atomic_set(&ent->count, 1); ent->pde_users = 0; spin_lock_init(&ent->pde_unload_lock); ent->pde_unload_completion = NULL; @@ -682,7 +693,6 @@ void free_proc_entry(struct proc_dir_entry *de) /* * Remove a /proc entry and free it if it's not currently in use. - * If it is in use, we set the 'deleted' flag. */ void remove_proc_entry(const char *name, struct proc_dir_entry *parent) { @@ -731,13 +741,8 @@ continue_removing: parent->nlink--; de->nlink = 0; WARN_ON(de->subdir); - if (!atomic_read(&de->count)) + if (atomic_dec_and_test(&de->count)) free_proc_entry(de); - else { - de->deleted = 1; - printk("remove_proc_entry: %s/%s busy, count=%d\n", - parent->name, de->name, atomic_read(&de->count)); - } break; } spin_unlock(&proc_subdir_lock); diff --git a/fs/proc/inode.c b/fs/proc/inode.c index abe6a3f04368..1a551d92e1d8 100644 --- a/fs/proc/inode.c +++ b/fs/proc/inode.c @@ -43,13 +43,8 @@ void de_put(struct proc_dir_entry *de) return; } - if (atomic_dec_and_test(&de->count)) { - if (de->deleted) { - printk("de_put: deferred delete of %s\n", - de->name); - free_proc_entry(de); - } - } + if (atomic_dec_and_test(&de->count)) + free_proc_entry(de); unlock_kernel(); } } diff --git a/fs/proc/proc_net.c b/fs/proc/proc_net.c index 131f9c68be5f..0afe21ee0607 100644 --- a/fs/proc/proc_net.c +++ b/fs/proc/proc_net.c @@ -50,89 +50,14 @@ struct net *get_proc_net(const struct inode *inode) } EXPORT_SYMBOL_GPL(get_proc_net); -static struct proc_dir_entry *proc_net_shadow; +static struct proc_dir_entry *shadow_pde; -static struct dentry *proc_net_shadow_dentry(struct dentry *parent, +static struct proc_dir_entry *proc_net_shadow(struct task_struct *task, struct proc_dir_entry *de) { - struct dentry *shadow = NULL; - struct inode *inode; - if (!de) - goto out; - de_get(de); - inode = proc_get_inode(parent->d_inode->i_sb, de->low_ino, de); - if (!inode) - goto out_de_put; - shadow = d_alloc_name(parent, de->name); - if (!shadow) - goto out_iput; - shadow->d_op = parent->d_op; /* proc_dentry_operations */ - d_instantiate(shadow, inode); -out: - return shadow; -out_iput: - iput(inode); -out_de_put: - de_put(de); - goto out; -} - -static void *proc_net_follow_link(struct dentry *parent, struct nameidata *nd) -{ - struct net *net = current->nsproxy->net_ns; - struct dentry *shadow; - shadow = proc_net_shadow_dentry(parent, net->proc_net); - if (!shadow) - return ERR_PTR(-ENOENT); - - dput(nd->dentry); - /* My dentry count is 1 and that should be enough as the - * shadow dentry is thrown away immediately. - */ - nd->dentry = shadow; - return NULL; + return task->nsproxy->net_ns->proc_net; } -static struct dentry *proc_net_lookup(struct inode *dir, struct dentry *dentry, - struct nameidata *nd) -{ - struct net *net = current->nsproxy->net_ns; - struct dentry *shadow; - - shadow = proc_net_shadow_dentry(nd->dentry, net->proc_net); - if (!shadow) - return ERR_PTR(-ENOENT); - - dput(nd->dentry); - nd->dentry = shadow; - - return shadow->d_inode->i_op->lookup(shadow->d_inode, dentry, nd); -} - -static int proc_net_setattr(struct dentry *dentry, struct iattr *iattr) -{ - struct net *net = current->nsproxy->net_ns; - struct dentry *shadow; - int ret; - - shadow = proc_net_shadow_dentry(dentry->d_parent, net->proc_net); - if (!shadow) - return -ENOENT; - ret = shadow->d_inode->i_op->setattr(shadow, iattr); - dput(shadow); - return ret; -} - -static const struct file_operations proc_net_dir_operations = { - .read = generic_read_dir, -}; - -static struct inode_operations proc_net_dir_inode_operations = { - .follow_link = proc_net_follow_link, - .lookup = proc_net_lookup, - .setattr = proc_net_setattr, -}; - static __net_init int proc_net_ns_init(struct net *net) { struct proc_dir_entry *root, *netd, *net_statd; @@ -185,9 +110,8 @@ static struct pernet_operations __net_initdata proc_net_ns_ops = { int __init proc_net_init(void) { - proc_net_shadow = proc_mkdir("net", NULL); - proc_net_shadow->proc_iops = &proc_net_dir_inode_operations; - proc_net_shadow->proc_fops = &proc_net_dir_operations; + shadow_pde = proc_mkdir("net", NULL); + shadow_pde->shadow_proc = proc_net_shadow; return register_pernet_subsys(&proc_net_ns_ops); } diff --git a/fs/proc/root.c b/fs/proc/root.c index ec9cb3b6c93b..81f99e691f99 100644 --- a/fs/proc/root.c +++ b/fs/proc/root.c @@ -207,6 +207,7 @@ struct proc_dir_entry proc_root = { .name = "/proc", .mode = S_IFDIR | S_IRUGO | S_IXUGO, .nlink = 2, + .count = ATOMIC_INIT(1), .proc_iops = &proc_root_inode_operations, .proc_fops = &proc_root_operations, .parent = &proc_root, diff --git a/fs/reiserfs/procfs.c b/fs/reiserfs/procfs.c index 9aa7a06e093f..001144621672 100644 --- a/fs/reiserfs/procfs.c +++ b/fs/reiserfs/procfs.c @@ -420,12 +420,6 @@ static void *r_start(struct seq_file *m, loff_t * pos) return NULL; up_write(&s->s_umount); - - if (de->deleted) { - deactivate_super(s); - return NULL; - } - return s; } diff --git a/fs/ufs/dir.c b/fs/ufs/dir.c index 30f8c2bb0c3e..aaf2878305ce 100644 --- a/fs/ufs/dir.c +++ b/fs/ufs/dir.c @@ -179,7 +179,7 @@ bad_entry: goto fail; Eend: p = (struct ufs_dir_entry *)(kaddr + offs); - ufs_error (sb, "ext2_check_page", + ufs_error(sb, __FUNCTION__, "entry in directory #%lu spans the page boundary" "offset=%lu", dir->i_ino, (page->index<<PAGE_CACHE_SHIFT)+offs); diff --git a/fs/ufs/super.c b/fs/ufs/super.c index c78c04fd993f..0072cb33ebec 100644 --- a/fs/ufs/super.c +++ b/fs/ufs/super.c @@ -755,13 +755,13 @@ static int ufs_fill_super(struct super_block *sb, void *data, int silent) break; case UFS_MOUNT_UFSTYPE_NEXTSTEP: - /*TODO: check may be we need set special dir block size?*/ UFSD("ufstype=nextstep\n"); uspi->s_fsize = block_size = 1024; uspi->s_fmask = ~(1024 - 1); uspi->s_fshift = 10; uspi->s_sbsize = super_block_size = 2048; uspi->s_sbbase = 0; + uspi->s_dirblksize = 1024; flags |= UFS_DE_OLD | UFS_UID_OLD | UFS_ST_OLD | UFS_CG_OLD; if (!(sb->s_flags & MS_RDONLY)) { if (!silent) @@ -771,13 +771,13 @@ static int ufs_fill_super(struct super_block *sb, void *data, int silent) break; case UFS_MOUNT_UFSTYPE_NEXTSTEP_CD: - /*TODO: check may be we need set special dir block size?*/ UFSD("ufstype=nextstep-cd\n"); uspi->s_fsize = block_size = 2048; uspi->s_fmask = ~(2048 - 1); uspi->s_fshift = 11; uspi->s_sbsize = super_block_size = 2048; uspi->s_sbbase = 0; + uspi->s_dirblksize = 1024; flags |= UFS_DE_OLD | UFS_UID_OLD | UFS_ST_OLD | UFS_CG_OLD; if (!(sb->s_flags & MS_RDONLY)) { if (!silent) diff --git a/include/asm-avr32/cacheflush.h b/include/asm-avr32/cacheflush.h index dfaaa88cd412..670674749b20 100644 --- a/include/asm-avr32/cacheflush.h +++ b/include/asm-avr32/cacheflush.h @@ -116,15 +116,16 @@ extern void flush_icache_page(struct vm_area_struct *vma, struct page *page); * flush with all configurations. */ extern void flush_icache_range(unsigned long start, unsigned long end); -extern void flush_icache_user_range(struct vm_area_struct *vma, - struct page *page, - unsigned long addr, int len); -#define copy_to_user_page(vma, page, vaddr, dst, src, len) do { \ - memcpy(dst, src, len); \ - flush_icache_user_range(vma, page, vaddr, len); \ -} while(0) -#define copy_from_user_page(vma, page, vaddr, dst, src, len) \ - memcpy(dst, src, len) +extern void copy_to_user_page(struct vm_area_struct *vma, struct page *page, + unsigned long vaddr, void *dst, const void *src, + unsigned long len); + +static inline void copy_from_user_page(struct vm_area_struct *vma, + struct page *page, unsigned long vaddr, void *dst, + const void *src, unsigned long len) +{ + memcpy(dst, src, len); +} #endif /* __ASM_AVR32_CACHEFLUSH_H */ diff --git a/include/asm-avr32/ocd.h b/include/asm-avr32/ocd.h index 46f73180a127..996405e0393f 100644 --- a/include/asm-avr32/ocd.h +++ b/include/asm-avr32/ocd.h @@ -1,7 +1,7 @@ /* - * AVR32 OCD Registers + * AVR32 OCD Interface and register definitions * - * Copyright (C) 2004-2006 Atmel Corporation + * Copyright (C) 2004-2007 Atmel Corporation * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as @@ -10,69 +10,529 @@ #ifndef __ASM_AVR32_OCD_H #define __ASM_AVR32_OCD_H -/* Debug Registers */ -#define DBGREG_DID 0 -#define DBGREG_DC 8 -#define DBGREG_DS 16 -#define DBGREG_RWCS 28 -#define DBGREG_RWA 36 -#define DBGREG_RWD 40 -#define DBGREG_WT 44 -#define DBGREG_DTC 52 -#define DBGREG_DTSA0 56 -#define DBGREG_DTSA1 60 -#define DBGREG_DTEA0 72 -#define DBGREG_DTEA1 76 -#define DBGREG_BWC0A 88 -#define DBGREG_BWC0B 92 -#define DBGREG_BWC1A 96 -#define DBGREG_BWC1B 100 -#define DBGREG_BWC2A 104 -#define DBGREG_BWC2B 108 -#define DBGREG_BWC3A 112 -#define DBGREG_BWC3B 116 -#define DBGREG_BWA0A 120 -#define DBGREG_BWA0B 124 -#define DBGREG_BWA1A 128 -#define DBGREG_BWA1B 132 -#define DBGREG_BWA2A 136 -#define DBGREG_BWA2B 140 -#define DBGREG_BWA3A 144 -#define DBGREG_BWA3B 148 -#define DBGREG_BWD3A 153 -#define DBGREG_BWD3B 156 - -#define DBGREG_PID 284 - -#define SABAH_OCD 0x01 -#define SABAH_ICACHE 0x02 -#define SABAH_MEM_CACHED 0x04 -#define SABAH_MEM_UNCACHED 0x05 - -/* Fields in the Development Control register */ -#define DC_SS_BIT 8 - -#define DC_SS (1 << DC_SS_BIT) -#define DC_DBE (1 << 13) -#define DC_RID (1 << 27) -#define DC_ORP (1 << 28) -#define DC_MM (1 << 29) -#define DC_RES (1 << 30) - -/* Fields in the Development Status register */ -#define DS_SSS (1 << 0) -#define DS_SWB (1 << 1) -#define DS_HWB (1 << 2) -#define DS_BP_SHIFT 8 -#define DS_BP_MASK (0xff << DS_BP_SHIFT) - -#define __mfdr(addr) \ -({ \ - register unsigned long value; \ - asm volatile("mfdr %0, %1" : "=r"(value) : "i"(addr)); \ - value; \ -}) -#define __mtdr(addr, value) \ - asm volatile("mtdr %0, %1" : : "i"(addr), "r"(value)) +/* OCD Register offsets. Abbreviations used below: + * + * BP Breakpoint + * Comm Communication + * DT Data Trace + * PC Program Counter + * PID Process ID + * R/W Read/Write + * WP Watchpoint + */ +#define OCD_DID 0x0000 /* Device ID */ +#define OCD_DC 0x0008 /* Development Control */ +#define OCD_DS 0x0010 /* Development Status */ +#define OCD_RWCS 0x001c /* R/W Access Control */ +#define OCD_RWA 0x0024 /* R/W Access Address */ +#define OCD_RWD 0x0028 /* R/W Access Data */ +#define OCD_WT 0x002c /* Watchpoint Trigger */ +#define OCD_DTC 0x0034 /* Data Trace Control */ +#define OCD_DTSA0 0x0038 /* DT Start Addr Channel 0 */ +#define OCD_DTSA1 0x003c /* DT Start Addr Channel 1 */ +#define OCD_DTEA0 0x0048 /* DT End Addr Channel 0 */ +#define OCD_DTEA1 0x004c /* DT End Addr Channel 1 */ +#define OCD_BWC0A 0x0058 /* PC BP/WP Control 0A */ +#define OCD_BWC0B 0x005c /* PC BP/WP Control 0B */ +#define OCD_BWC1A 0x0060 /* PC BP/WP Control 1A */ +#define OCD_BWC1B 0x0064 /* PC BP/WP Control 1B */ +#define OCD_BWC2A 0x0068 /* PC BP/WP Control 2A */ +#define OCD_BWC2B 0x006c /* PC BP/WP Control 2B */ +#define OCD_BWC3A 0x0070 /* Data BP/WP Control 3A */ +#define OCD_BWC3B 0x0074 /* Data BP/WP Control 3B */ +#define OCD_BWA0A 0x0078 /* PC BP/WP Address 0A */ +#define OCD_BWA0B 0x007c /* PC BP/WP Address 0B */ +#define OCD_BWA1A 0x0080 /* PC BP/WP Address 1A */ +#define OCD_BWA1B 0x0084 /* PC BP/WP Address 1B */ +#define OCD_BWA2A 0x0088 /* PC BP/WP Address 2A */ +#define OCD_BWA2B 0x008c /* PC BP/WP Address 2B */ +#define OCD_BWA3A 0x0090 /* Data BP/WP Address 3A */ +#define OCD_BWA3B 0x0094 /* Data BP/WP Address 3B */ +#define OCD_NXCFG 0x0100 /* Nexus Configuration */ +#define OCD_DINST 0x0104 /* Debug Instruction */ +#define OCD_DPC 0x0108 /* Debug Program Counter */ +#define OCD_CPUCM 0x010c /* CPU Control Mask */ +#define OCD_DCCPU 0x0110 /* Debug Comm CPU */ +#define OCD_DCEMU 0x0114 /* Debug Comm Emulator */ +#define OCD_DCSR 0x0118 /* Debug Comm Status */ +#define OCD_PID 0x011c /* Ownership Trace PID */ +#define OCD_EPC0 0x0120 /* Event Pair Control 0 */ +#define OCD_EPC1 0x0124 /* Event Pair Control 1 */ +#define OCD_EPC2 0x0128 /* Event Pair Control 2 */ +#define OCD_EPC3 0x012c /* Event Pair Control 3 */ +#define OCD_AXC 0x0130 /* AUX port Control */ + +/* Bits in DID */ +#define OCD_DID_MID_START 1 +#define OCD_DID_MID_SIZE 11 +#define OCD_DID_PN_START 12 +#define OCD_DID_PN_SIZE 16 +#define OCD_DID_RN_START 28 +#define OCD_DID_RN_SIZE 4 + +/* Bits in DC */ +#define OCD_DC_TM_START 0 +#define OCD_DC_TM_SIZE 2 +#define OCD_DC_EIC_START 3 +#define OCD_DC_EIC_SIZE 2 +#define OCD_DC_OVC_START 5 +#define OCD_DC_OVC_SIZE 3 +#define OCD_DC_SS_BIT 8 +#define OCD_DC_DBR_BIT 12 +#define OCD_DC_DBE_BIT 13 +#define OCD_DC_EOS_START 20 +#define OCD_DC_EOS_SIZE 2 +#define OCD_DC_SQA_BIT 22 +#define OCD_DC_IRP_BIT 23 +#define OCD_DC_IFM_BIT 24 +#define OCD_DC_TOZ_BIT 25 +#define OCD_DC_TSR_BIT 26 +#define OCD_DC_RID_BIT 27 +#define OCD_DC_ORP_BIT 28 +#define OCD_DC_MM_BIT 29 +#define OCD_DC_RES_BIT 30 +#define OCD_DC_ABORT_BIT 31 + +/* Bits in DS */ +#define OCD_DS_SSS_BIT 0 +#define OCD_DS_SWB_BIT 1 +#define OCD_DS_HWB_BIT 2 +#define OCD_DS_HWE_BIT 3 +#define OCD_DS_STP_BIT 4 +#define OCD_DS_DBS_BIT 5 +#define OCD_DS_BP_START 8 +#define OCD_DS_BP_SIZE 8 +#define OCD_DS_INC_BIT 24 +#define OCD_DS_BOZ_BIT 25 +#define OCD_DS_DBA_BIT 26 +#define OCD_DS_EXB_BIT 27 +#define OCD_DS_NTBF_BIT 28 + +/* Bits in RWCS */ +#define OCD_RWCS_DV_BIT 0 +#define OCD_RWCS_ERR_BIT 1 +#define OCD_RWCS_CNT_START 2 +#define OCD_RWCS_CNT_SIZE 14 +#define OCD_RWCS_CRC_BIT 19 +#define OCD_RWCS_NTBC_START 20 +#define OCD_RWCS_NTBC_SIZE 2 +#define OCD_RWCS_NTE_BIT 22 +#define OCD_RWCS_NTAP_BIT 23 +#define OCD_RWCS_WRAPPED_BIT 24 +#define OCD_RWCS_CCTRL_START 25 +#define OCD_RWCS_CCTRL_SIZE 2 +#define OCD_RWCS_SZ_START 27 +#define OCD_RWCS_SZ_SIZE 3 +#define OCD_RWCS_RW_BIT 30 +#define OCD_RWCS_AC_BIT 31 + +/* Bits in RWA */ +#define OCD_RWA_RWA_START 0 +#define OCD_RWA_RWA_SIZE 32 + +/* Bits in RWD */ +#define OCD_RWD_RWD_START 0 +#define OCD_RWD_RWD_SIZE 32 + +/* Bits in WT */ +#define OCD_WT_DTE_START 20 +#define OCD_WT_DTE_SIZE 3 +#define OCD_WT_DTS_START 23 +#define OCD_WT_DTS_SIZE 3 +#define OCD_WT_PTE_START 26 +#define OCD_WT_PTE_SIZE 3 +#define OCD_WT_PTS_START 29 +#define OCD_WT_PTS_SIZE 3 + +/* Bits in DTC */ +#define OCD_DTC_T0WP_BIT 0 +#define OCD_DTC_T1WP_BIT 1 +#define OCD_DTC_ASID0EN_BIT 2 +#define OCD_DTC_ASID0_START 3 +#define OCD_DTC_ASID0_SIZE 8 +#define OCD_DTC_ASID1EN_BIT 11 +#define OCD_DTC_ASID1_START 12 +#define OCD_DTC_ASID1_SIZE 8 +#define OCD_DTC_RWT1_START 28 +#define OCD_DTC_RWT1_SIZE 2 +#define OCD_DTC_RWT0_START 30 +#define OCD_DTC_RWT0_SIZE 2 + +/* Bits in DTSA0 */ +#define OCD_DTSA0_DTSA_START 0 +#define OCD_DTSA0_DTSA_SIZE 32 + +/* Bits in DTSA1 */ +#define OCD_DTSA1_DTSA_START 0 +#define OCD_DTSA1_DTSA_SIZE 32 + +/* Bits in DTEA0 */ +#define OCD_DTEA0_DTEA_START 0 +#define OCD_DTEA0_DTEA_SIZE 32 + +/* Bits in DTEA1 */ +#define OCD_DTEA1_DTEA_START 0 +#define OCD_DTEA1_DTEA_SIZE 32 + +/* Bits in BWC0A */ +#define OCD_BWC0A_ASIDEN_BIT 0 +#define OCD_BWC0A_ASID_START 1 +#define OCD_BWC0A_ASID_SIZE 8 +#define OCD_BWC0A_EOC_BIT 14 +#define OCD_BWC0A_AME_BIT 25 +#define OCD_BWC0A_BWE_START 30 +#define OCD_BWC0A_BWE_SIZE 2 + +/* Bits in BWC0B */ +#define OCD_BWC0B_ASIDEN_BIT 0 +#define OCD_BWC0B_ASID_START 1 +#define OCD_BWC0B_ASID_SIZE 8 +#define OCD_BWC0B_EOC_BIT 14 +#define OCD_BWC0B_AME_BIT 25 +#define OCD_BWC0B_BWE_START 30 +#define OCD_BWC0B_BWE_SIZE 2 + +/* Bits in BWC1A */ +#define OCD_BWC1A_ASIDEN_BIT 0 +#define OCD_BWC1A_ASID_START 1 +#define OCD_BWC1A_ASID_SIZE 8 +#define OCD_BWC1A_EOC_BIT 14 +#define OCD_BWC1A_AME_BIT 25 +#define OCD_BWC1A_BWE_START 30 +#define OCD_BWC1A_BWE_SIZE 2 + +/* Bits in BWC1B */ +#define OCD_BWC1B_ASIDEN_BIT 0 +#define OCD_BWC1B_ASID_START 1 +#define OCD_BWC1B_ASID_SIZE 8 +#define OCD_BWC1B_EOC_BIT 14 +#define OCD_BWC1B_AME_BIT 25 +#define OCD_BWC1B_BWE_START 30 +#define OCD_BWC1B_BWE_SIZE 2 + +/* Bits in BWC2A */ +#define OCD_BWC2A_ASIDEN_BIT 0 +#define OCD_BWC2A_ASID_START 1 +#define OCD_BWC2A_ASID_SIZE 8 +#define OCD_BWC2A_EOC_BIT 14 +#define OCD_BWC2A_AMB_START 20 +#define OCD_BWC2A_AMB_SIZE 5 +#define OCD_BWC2A_AME_BIT 25 +#define OCD_BWC2A_BWE_START 30 +#define OCD_BWC2A_BWE_SIZE 2 + +/* Bits in BWC2B */ +#define OCD_BWC2B_ASIDEN_BIT 0 +#define OCD_BWC2B_ASID_START 1 +#define OCD_BWC2B_ASID_SIZE 8 +#define OCD_BWC2B_EOC_BIT 14 +#define OCD_BWC2B_AME_BIT 25 +#define OCD_BWC2B_BWE_START 30 +#define OCD_BWC2B_BWE_SIZE 2 + +/* Bits in BWC3A */ +#define OCD_BWC3A_ASIDEN_BIT 0 +#define OCD_BWC3A_ASID_START 1 +#define OCD_BWC3A_ASID_SIZE 8 +#define OCD_BWC3A_SIZE_START 9 +#define OCD_BWC3A_SIZE_SIZE 3 +#define OCD_BWC3A_EOC_BIT 14 +#define OCD_BWC3A_BWO_START 16 +#define OCD_BWC3A_BWO_SIZE 2 +#define OCD_BWC3A_BME_START 20 +#define OCD_BWC3A_BME_SIZE 4 +#define OCD_BWC3A_BRW_START 28 +#define OCD_BWC3A_BRW_SIZE 2 +#define OCD_BWC3A_BWE_START 30 +#define OCD_BWC3A_BWE_SIZE 2 + +/* Bits in BWC3B */ +#define OCD_BWC3B_ASIDEN_BIT 0 +#define OCD_BWC3B_ASID_START 1 +#define OCD_BWC3B_ASID_SIZE 8 +#define OCD_BWC3B_SIZE_START 9 +#define OCD_BWC3B_SIZE_SIZE 3 +#define OCD_BWC3B_EOC_BIT 14 +#define OCD_BWC3B_BWO_START 16 +#define OCD_BWC3B_BWO_SIZE 2 +#define OCD_BWC3B_BME_START 20 +#define OCD_BWC3B_BME_SIZE 4 +#define OCD_BWC3B_BRW_START 28 +#define OCD_BWC3B_BRW_SIZE 2 +#define OCD_BWC3B_BWE_START 30 +#define OCD_BWC3B_BWE_SIZE 2 + +/* Bits in BWA0A */ +#define OCD_BWA0A_BWA_START 0 +#define OCD_BWA0A_BWA_SIZE 32 + +/* Bits in BWA0B */ +#define OCD_BWA0B_BWA_START 0 +#define OCD_BWA0B_BWA_SIZE 32 + +/* Bits in BWA1A */ +#define OCD_BWA1A_BWA_START 0 +#define OCD_BWA1A_BWA_SIZE 32 + +/* Bits in BWA1B */ +#define OCD_BWA1B_BWA_START 0 +#define OCD_BWA1B_BWA_SIZE 32 + +/* Bits in BWA2A */ +#define OCD_BWA2A_BWA_START 0 +#define OCD_BWA2A_BWA_SIZE 32 + +/* Bits in BWA2B */ +#define OCD_BWA2B_BWA_START 0 +#define OCD_BWA2B_BWA_SIZE 32 + +/* Bits in BWA3A */ +#define OCD_BWA3A_BWA_START 0 +#define OCD_BWA3A_BWA_SIZE 32 + +/* Bits in BWA3B */ +#define OCD_BWA3B_BWA_START 0 +#define OCD_BWA3B_BWA_SIZE 32 + +/* Bits in NXCFG */ +#define OCD_NXCFG_NXARCH_START 0 +#define OCD_NXCFG_NXARCH_SIZE 4 +#define OCD_NXCFG_NXOCD_START 4 +#define OCD_NXCFG_NXOCD_SIZE 4 +#define OCD_NXCFG_NXPCB_START 8 +#define OCD_NXCFG_NXPCB_SIZE 4 +#define OCD_NXCFG_NXDB_START 12 +#define OCD_NXCFG_NXDB_SIZE 4 +#define OCD_NXCFG_MXMSEO_BIT 16 +#define OCD_NXCFG_NXMDO_START 17 +#define OCD_NXCFG_NXMDO_SIZE 4 +#define OCD_NXCFG_NXPT_BIT 21 +#define OCD_NXCFG_NXOT_BIT 22 +#define OCD_NXCFG_NXDWT_BIT 23 +#define OCD_NXCFG_NXDRT_BIT 24 +#define OCD_NXCFG_NXDTC_START 25 +#define OCD_NXCFG_NXDTC_SIZE 3 +#define OCD_NXCFG_NXDMA_BIT 28 + +/* Bits in DINST */ +#define OCD_DINST_DINST_START 0 +#define OCD_DINST_DINST_SIZE 32 + +/* Bits in CPUCM */ +#define OCD_CPUCM_BEM_BIT 1 +#define OCD_CPUCM_FEM_BIT 2 +#define OCD_CPUCM_REM_BIT 3 +#define OCD_CPUCM_IBEM_BIT 4 +#define OCD_CPUCM_IEEM_BIT 5 + +/* Bits in DCCPU */ +#define OCD_DCCPU_DATA_START 0 +#define OCD_DCCPU_DATA_SIZE 32 + +/* Bits in DCEMU */ +#define OCD_DCEMU_DATA_START 0 +#define OCD_DCEMU_DATA_SIZE 32 + +/* Bits in DCSR */ +#define OCD_DCSR_CPUD_BIT 0 +#define OCD_DCSR_EMUD_BIT 1 + +/* Bits in PID */ +#define OCD_PID_PROCESS_START 0 +#define OCD_PID_PROCESS_SIZE 32 + +/* Bits in EPC0 */ +#define OCD_EPC0_RNG_START 0 +#define OCD_EPC0_RNG_SIZE 2 +#define OCD_EPC0_CE_BIT 4 +#define OCD_EPC0_ECNT_START 16 +#define OCD_EPC0_ECNT_SIZE 16 + +/* Bits in EPC1 */ +#define OCD_EPC1_RNG_START 0 +#define OCD_EPC1_RNG_SIZE 2 +#define OCD_EPC1_ATB_BIT 5 +#define OCD_EPC1_AM_BIT 6 + +/* Bits in EPC2 */ +#define OCD_EPC2_RNG_START 0 +#define OCD_EPC2_RNG_SIZE 2 +#define OCD_EPC2_DB_START 2 +#define OCD_EPC2_DB_SIZE 2 + +/* Bits in EPC3 */ +#define OCD_EPC3_RNG_START 0 +#define OCD_EPC3_RNG_SIZE 2 +#define OCD_EPC3_DWE_BIT 2 + +/* Bits in AXC */ +#define OCD_AXC_DIV_START 0 +#define OCD_AXC_DIV_SIZE 4 +#define OCD_AXC_AXE_BIT 8 +#define OCD_AXC_AXS_BIT 9 +#define OCD_AXC_DDR_BIT 10 +#define OCD_AXC_LS_BIT 11 +#define OCD_AXC_REX_BIT 12 +#define OCD_AXC_REXTEN_BIT 13 + +/* Constants for DC:EIC */ +#define OCD_EIC_PROGRAM_AND_DATA_TRACE 0 +#define OCD_EIC_BREAKPOINT 1 +#define OCD_EIC_NOP 2 + +/* Constants for DC:OVC */ +#define OCD_OVC_OVERRUN 0 +#define OCD_OVC_DELAY_CPU_BTM 1 +#define OCD_OVC_DELAY_CPU_DTM 2 +#define OCD_OVC_DELAY_CPU_BTM_DTM 3 + +/* Constants for DC:EOS */ +#define OCD_EOS_NOP 0 +#define OCD_EOS_DEBUG_MODE 1 +#define OCD_EOS_BREAKPOINT_WATCHPOINT 2 +#define OCD_EOS_THQ 3 + +/* Constants for RWCS:NTBC */ +#define OCD_NTBC_OVERWRITE 0 +#define OCD_NTBC_DISABLE 1 +#define OCD_NTBC_BREAKPOINT 2 + +/* Constants for RWCS:CCTRL */ +#define OCD_CCTRL_AUTO 0 +#define OCD_CCTRL_CACHED 1 +#define OCD_CCTRL_UNCACHED 2 + +/* Constants for RWCS:SZ */ +#define OCD_SZ_BYTE 0 +#define OCD_SZ_HALFWORD 1 +#define OCD_SZ_WORD 2 + +/* Constants for WT:PTS */ +#define OCD_PTS_DISABLED 0 +#define OCD_PTS_PROGRAM_0B 1 +#define OCD_PTS_PROGRAM_1A 2 +#define OCD_PTS_PROGRAM_1B 3 +#define OCD_PTS_PROGRAM_2A 4 +#define OCD_PTS_PROGRAM_2B 5 +#define OCD_PTS_DATA_3A 6 +#define OCD_PTS_DATA_3B 7 + +/* Constants for DTC:RWT1 */ +#define OCD_RWT1_NO_TRACE 0 +#define OCD_RWT1_DATA_READ 1 +#define OCD_RWT1_DATA_WRITE 2 +#define OCD_RWT1_DATA_READ_WRITE 3 + +/* Constants for DTC:RWT0 */ +#define OCD_RWT0_NO_TRACE 0 +#define OCD_RWT0_DATA_READ 1 +#define OCD_RWT0_DATA_WRITE 2 +#define OCD_RWT0_DATA_READ_WRITE 3 + +/* Constants for BWC0A:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for BWC0B:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for BWC1A:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for BWC1B:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for BWC2A:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for BWC2B:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for BWC3A:SIZE */ +#define OCD_SIZE_BYTE_ACCESS 4 +#define OCD_SIZE_HALFWORD_ACCESS 5 +#define OCD_SIZE_WORD_ACCESS 6 +#define OCD_SIZE_DOUBLE_WORD_ACCESS 7 + +/* Constants for BWC3A:BRW */ +#define OCD_BRW_READ_BREAK 0 +#define OCD_BRW_WRITE_BREAK 1 +#define OCD_BRW_ANY_ACCES_BREAK 2 + +/* Constants for BWC3A:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for BWC3B:SIZE */ +#define OCD_SIZE_BYTE_ACCESS 4 +#define OCD_SIZE_HALFWORD_ACCESS 5 +#define OCD_SIZE_WORD_ACCESS 6 +#define OCD_SIZE_DOUBLE_WORD_ACCESS 7 + +/* Constants for BWC3B:BRW */ +#define OCD_BRW_READ_BREAK 0 +#define OCD_BRW_WRITE_BREAK 1 +#define OCD_BRW_ANY_ACCES_BREAK 2 + +/* Constants for BWC3B:BWE */ +#define OCD_BWE_DISABLED 0 +#define OCD_BWE_BREAKPOINT_ENABLED 1 +#define OCD_BWE_WATCHPOINT_ENABLED 3 + +/* Constants for EPC0:RNG */ +#define OCD_RNG_DISABLED 0 +#define OCD_RNG_EXCLUSIVE 1 +#define OCD_RNG_INCLUSIVE 2 + +/* Constants for EPC1:RNG */ +#define OCD_RNG_DISABLED 0 +#define OCD_RNG_EXCLUSIVE 1 +#define OCD_RNG_INCLUSIVE 2 + +/* Constants for EPC2:RNG */ +#define OCD_RNG_DISABLED 0 +#define OCD_RNG_EXCLUSIVE 1 +#define OCD_RNG_INCLUSIVE 2 + +/* Constants for EPC2:DB */ +#define OCD_DB_DISABLED 0 +#define OCD_DB_CHAINED_B 1 +#define OCD_DB_CHAINED_A 2 +#define OCD_DB_AHAINED_A_AND_B 3 + +/* Constants for EPC3:RNG */ +#define OCD_RNG_DISABLED 0 +#define OCD_RNG_EXCLUSIVE 1 +#define OCD_RNG_INCLUSIVE 2 + +#ifndef __ASSEMBLER__ + +/* Register access macros */ +static inline unsigned long __ocd_read(unsigned int reg) +{ + return __builtin_mfdr(reg); +} + +static inline void __ocd_write(unsigned int reg, unsigned long value) +{ + __builtin_mtdr(reg, value); +} + +#define ocd_read(reg) __ocd_read(OCD_##reg) +#define ocd_write(reg, value) __ocd_write(OCD_##reg, value) + +#endif /* !__ASSEMBLER__ */ #endif /* __ASM_AVR32_OCD_H */ diff --git a/include/asm-avr32/processor.h b/include/asm-avr32/processor.h index 6a64833756a6..a52576b25afe 100644 --- a/include/asm-avr32/processor.h +++ b/include/asm-avr32/processor.h @@ -139,6 +139,9 @@ extern void show_regs_log_lvl(struct pt_regs *regs, const char *log_lvl); extern void show_stack_log_lvl(struct task_struct *tsk, unsigned long sp, struct pt_regs *regs, const char *log_lvl); +#define task_pt_regs(p) \ + ((struct pt_regs *)(THREAD_SIZE + task_stack_page(p)) - 1) + #define KSTK_EIP(tsk) ((tsk)->thread.cpu_context.pc) #define KSTK_ESP(tsk) ((tsk)->thread.cpu_context.ksp) diff --git a/include/asm-avr32/ptrace.h b/include/asm-avr32/ptrace.h index 60f0f19a81f1..8c5dba5e33df 100644 --- a/include/asm-avr32/ptrace.h +++ b/include/asm-avr32/ptrace.h @@ -14,8 +14,7 @@ /* * Status Register bits */ -#define SR_H 0x40000000 -#define SR_R 0x20000000 +#define SR_H 0x20000000 #define SR_J 0x10000000 #define SR_DM 0x08000000 #define SR_D 0x04000000 @@ -35,8 +34,7 @@ #define SR_I0M 0x00020000 #define SR_GM 0x00010000 -#define SR_H_BIT 30 -#define SR_R_BIT 29 +#define SR_H_BIT 29 #define SR_J_BIT 28 #define SR_DM_BIT 27 #define SR_D_BIT 26 diff --git a/include/asm-avr32/sysreg.h b/include/asm-avr32/sysreg.h index dd21182b60e0..d4e0950170ca 100644 --- a/include/asm-avr32/sysreg.h +++ b/include/asm-avr32/sysreg.h @@ -93,6 +93,8 @@ #define SYSREG_I3M_SIZE 1 #define SYSREG_EM_OFFSET 21 #define SYSREG_EM_SIZE 1 +#define SYSREG_MODE_OFFSET 22 +#define SYSREG_MODE_SIZE 3 #define SYSREG_M0_OFFSET 22 #define SYSREG_M0_SIZE 1 #define SYSREG_M1_OFFSET 23 diff --git a/include/asm-avr32/system.h b/include/asm-avr32/system.h index dc2d527cef41..c600cc15cbcb 100644 --- a/include/asm-avr32/system.h +++ b/include/asm-avr32/system.h @@ -35,8 +35,8 @@ #include <asm/ocd.h> #define finish_arch_switch(prev) \ do { \ - __mtdr(DBGREG_PID, prev->pid); \ - __mtdr(DBGREG_PID, current->pid); \ + ocd_write(PID, prev->pid); \ + ocd_write(PID, current->pid); \ } while(0) #endif diff --git a/include/asm-avr32/thread_info.h b/include/asm-avr32/thread_info.h index 17dacf3f36d3..184b574289b4 100644 --- a/include/asm-avr32/thread_info.h +++ b/include/asm-avr32/thread_info.h @@ -25,6 +25,11 @@ struct thread_info { unsigned long flags; /* low level flags */ __u32 cpu; __s32 preempt_count; /* 0 => preemptable, <0 => BUG */ + __u32 rar_saved; /* return address... */ + __u32 rsr_saved; /* ...and status register + saved by debug handler + when setting up + trampoline */ struct restart_block restart_block; __u8 supervisor_stack[0]; }; @@ -78,8 +83,8 @@ static inline struct thread_info *current_thread_info(void) #define TIF_NEED_RESCHED 2 /* rescheduling necessary */ #define TIF_POLLING_NRFLAG 3 /* true if poll_idle() is polling TIF_NEED_RESCHED */ -#define TIF_BREAKPOINT 4 /* true if we should break after return */ -#define TIF_SINGLE_STEP 5 /* single step after next break */ +#define TIF_BREAKPOINT 4 /* enter monitor mode on return */ +#define TIF_SINGLE_STEP 5 /* single step in progress */ #define TIF_MEMDIE 6 #define TIF_RESTORE_SIGMASK 7 /* restore signal mask in do_signal */ #define TIF_CPU_GOING_TO_SLEEP 8 /* CPU is entering sleep 0 mode */ @@ -89,18 +94,24 @@ static inline struct thread_info *current_thread_info(void) #define _TIF_SIGPENDING (1 << TIF_SIGPENDING) #define _TIF_NEED_RESCHED (1 << TIF_NEED_RESCHED) #define _TIF_POLLING_NRFLAG (1 << TIF_POLLING_NRFLAG) -#define _TIF_BREAKPOINT (1 << TIF_BREAKPOINT) #define _TIF_SINGLE_STEP (1 << TIF_SINGLE_STEP) #define _TIF_MEMDIE (1 << TIF_MEMDIE) #define _TIF_RESTORE_SIGMASK (1 << TIF_RESTORE_SIGMASK) #define _TIF_CPU_GOING_TO_SLEEP (1 << TIF_CPU_GOING_TO_SLEEP) -/* XXX: These two masks must never span more than 16 bits! */ +/* Note: The masks below must never span more than 16 bits! */ + /* work to do on interrupt/exception return */ -#define _TIF_WORK_MASK 0x0000013e +#define _TIF_WORK_MASK \ + ((1 << TIF_SIGPENDING) \ + | (1 << TIF_NEED_RESCHED) \ + | (1 << TIF_POLLING_NRFLAG) \ + | (1 << TIF_BREAKPOINT) \ + | (1 << TIF_RESTORE_SIGMASK)) + /* work to do on any return to userspace */ -#define _TIF_ALLWORK_MASK 0x0000013f +#define _TIF_ALLWORK_MASK (_TIF_WORK_MASK | (1 << TIF_SYSCALL_TRACE)) /* work to do on return from debug mode */ -#define _TIF_DBGWORK_MASK 0x0000017e +#define _TIF_DBGWORK_MASK (_TIF_WORK_MASK & ~(1 << TIF_BREAKPOINT)) #endif /* __ASM_AVR32_THREAD_INFO_H */ diff --git a/include/asm-blackfin/bfin5xx_spi.h b/include/asm-blackfin/bfin5xx_spi.h index f617d8765451..1a0b57f6a3d4 100644 --- a/include/asm-blackfin/bfin5xx_spi.h +++ b/include/asm-blackfin/bfin5xx_spi.h @@ -152,6 +152,7 @@ struct bfin5xx_spi_master { u16 num_chipselect; u8 enable_dma; + u16 pin_req[4]; }; /* spi_board_info.controller_data for SPI slave devices, @@ -162,7 +163,7 @@ struct bfin5xx_spi_chip { u8 enable_dma; u8 bits_per_word; u8 cs_change_per_word; - u8 cs_chg_udelay; + u16 cs_chg_udelay; /* Some devices require 16-bit delays */ }; #endif /* _SPI_CHANNEL_H_ */ diff --git a/include/asm-blackfin/mach-bf533/portmux.h b/include/asm-blackfin/mach-bf533/portmux.h index b88d7a03ee3e..137f4884acfe 100644 --- a/include/asm-blackfin/mach-bf533/portmux.h +++ b/include/asm-blackfin/mach-bf533/portmux.h @@ -42,7 +42,7 @@ #define P_SPORT0_DRPRI (P_DONTCARE) #define P_SPI0_MOSI (P_DONTCARE) -#define P_SPI0_MIS0 (P_DONTCARE) +#define P_SPI0_MISO (P_DONTCARE) #define P_SPI0_SCK (P_DONTCARE) #define P_SPI0_SSEL7 (P_DEFINED | P_IDENT(GPIO_PF7)) #define P_SPI0_SSEL6 (P_DEFINED | P_IDENT(GPIO_PF6)) diff --git a/include/asm-blackfin/mach-bf548/defBF54x_base.h b/include/asm-blackfin/mach-bf548/defBF54x_base.h index da979cb62f7d..319a48590c9c 100644 --- a/include/asm-blackfin/mach-bf548/defBF54x_base.h +++ b/include/asm-blackfin/mach-bf548/defBF54x_base.h @@ -1644,8 +1644,25 @@ #define RESTART 0x20 /* Work Unit Transitions */ #define DI_SEL 0x40 /* Data Interrupt Timing Select */ #define DI_EN 0x80 /* Data Interrupt Enable */ + #define NDSIZE 0xf00 /* Flex Descriptor Size */ +#define NDSIZE_0 0x0000 /* Next Descriptor Size = 0 (Stop/Autobuffer) */ +#define NDSIZE_1 0x0100 /* Next Descriptor Size = 1 */ +#define NDSIZE_2 0x0200 /* Next Descriptor Size = 2 */ +#define NDSIZE_3 0x0300 /* Next Descriptor Size = 3 */ +#define NDSIZE_4 0x0400 /* Next Descriptor Size = 4 */ +#define NDSIZE_5 0x0500 /* Next Descriptor Size = 5 */ +#define NDSIZE_6 0x0600 /* Next Descriptor Size = 6 */ +#define NDSIZE_7 0x0700 /* Next Descriptor Size = 7 */ +#define NDSIZE_8 0x0800 /* Next Descriptor Size = 8 */ +#define NDSIZE_9 0x0900 /* Next Descriptor Size = 9 */ + #define DMAFLOW 0xf000 /* Next Operation */ +#define DMAFLOW_STOP 0x0000 /* Stop Mode */ +#define DMAFLOW_AUTO 0x1000 /* Autobuffer Mode */ +#define DMAFLOW_ARRAY 0x4000 /* Descriptor Array Mode */ +#define DMAFLOW_SMALL 0x6000 /* Small Model Descriptor List Mode */ +#define DMAFLOW_LARGE 0x7000 /* Large Model Descriptor List Mode */ /* Bit masks for DMAx_IRQ_STATUS, MDMA_Sx_IRQ_STATUS, MDMA_Dx_IRQ_STATUS */ diff --git a/include/asm-mips/mach-au1x00/au1000.h b/include/asm-mips/mach-au1x00/au1000.h index 3bdce9126f16..bf7701243d71 100644 --- a/include/asm-mips/mach-au1x00/au1000.h +++ b/include/asm-mips/mach-au1x00/au1000.h @@ -526,7 +526,7 @@ extern struct au1xxx_irqmap au1xxx_irq_map[]; /* Au1000 */ #ifdef CONFIG_SOC_AU1000 enum soc_au1000_ints { - AU1000_FIRST_INT = MIPS_CPU_IRQ_BASE, + AU1000_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, AU1000_UART0_INT = AU1000_FIRST_INT, AU1000_UART1_INT, /* au1000 */ AU1000_UART2_INT, /* au1000 */ @@ -605,7 +605,7 @@ enum soc_au1000_ints { /* Au1500 */ #ifdef CONFIG_SOC_AU1500 enum soc_au1500_ints { - AU1500_FIRST_INT = MIPS_CPU_IRQ_BASE, + AU1500_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, AU1500_UART0_INT = AU1500_FIRST_INT, AU1000_PCI_INTA, /* au1500 */ AU1000_PCI_INTB, /* au1500 */ @@ -686,7 +686,7 @@ enum soc_au1500_ints { /* Au1100 */ #ifdef CONFIG_SOC_AU1100 enum soc_au1100_ints { - AU1100_FIRST_INT = MIPS_CPU_IRQ_BASE, + AU1100_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, AU1100_UART0_INT, AU1100_UART1_INT, AU1100_SD_INT, @@ -761,7 +761,7 @@ enum soc_au1100_ints { #ifdef CONFIG_SOC_AU1550 enum soc_au1550_ints { - AU1550_FIRST_INT = MIPS_CPU_IRQ_BASE, + AU1550_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, AU1550_UART0_INT = AU1550_FIRST_INT, AU1550_PCI_INTA, AU1550_PCI_INTB, @@ -851,7 +851,7 @@ enum soc_au1550_ints { #ifdef CONFIG_SOC_AU1200 enum soc_au1200_ints { - AU1200_FIRST_INT = MIPS_CPU_IRQ_BASE, + AU1200_FIRST_INT = MIPS_CPU_IRQ_BASE + 8, AU1200_UART0_INT = AU1200_FIRST_INT, AU1200_SWT_INT, AU1200_SD_INT, @@ -948,11 +948,12 @@ enum soc_au1200_ints { #endif /* CONFIG_SOC_AU1200 */ -#define AU1000_INTC0_INT_BASE (MIPS_CPU_IRQ_BASE + 0) -#define AU1000_INTC0_INT_LAST (MIPS_CPU_IRQ_BASE + 31) -#define AU1000_INTC1_INT_BASE (MIPS_CPU_IRQ_BASE + 32) -#define AU1000_INTC1_INT_LAST (MIPS_CPU_IRQ_BASE + 63) -#define AU1000_MAX_INTR (MIPS_CPU_IRQ_BASE + 63) +#define AU1000_INTC0_INT_BASE (MIPS_CPU_IRQ_BASE + 8) +#define AU1000_INTC0_INT_LAST (AU1000_INTC0_INT_BASE + 31) +#define AU1000_INTC1_INT_BASE (AU1000_INTC0_INT_BASE + 32) +#define AU1000_INTC1_INT_LAST (AU1000_INTC1_INT_BASE + 31) + +#define AU1000_MAX_INTR AU1000_INTC1_INT_LAST #define INTX 0xFF /* not valid */ /* Programmable Counters 0 and 1 */ diff --git a/include/asm-parisc/pdc.h b/include/asm-parisc/pdc.h index 5e0c3ca5450b..deda8c311373 100644 --- a/include/asm-parisc/pdc.h +++ b/include/asm-parisc/pdc.h @@ -645,8 +645,7 @@ int pdc_soft_power_button(int sw_control); void pdc_io_reset(void); void pdc_io_reset_devices(void); int pdc_iodc_getc(void); -void pdc_iodc_putc(unsigned char c); -void pdc_iodc_outc(unsigned char c); +int pdc_iodc_print(unsigned char *str, unsigned count); void pdc_printf(const char *fmt, ...); void pdc_emergency_unlock(void); diff --git a/include/asm-powerpc/pgtable-ppc32.h b/include/asm-powerpc/pgtable-ppc32.h index fea2d8ff1e73..d1332bbcbd9b 100644 --- a/include/asm-powerpc/pgtable-ppc32.h +++ b/include/asm-powerpc/pgtable-ppc32.h @@ -86,6 +86,11 @@ extern int icache_44x_need_flush; * entries per page directory level: our page-table tree is two-level, so * we don't really have any PMD directory. */ +#ifndef __ASSEMBLY__ +#define PTE_TABLE_SIZE (sizeof(pte_t) << PTE_SHIFT) +#define PGD_TABLE_SIZE (sizeof(pgd_t) << (32 - PGDIR_SHIFT)) +#endif /* __ASSEMBLY__ */ + #define PTRS_PER_PTE (1 << PTE_SHIFT) #define PTRS_PER_PMD 1 #define PTRS_PER_PGD (1 << (32 - PGDIR_SHIFT)) diff --git a/include/asm-powerpc/time.h b/include/asm-powerpc/time.h index 780f82642756..ce5de6e0e690 100644 --- a/include/asm-powerpc/time.h +++ b/include/asm-powerpc/time.h @@ -237,18 +237,14 @@ struct cpu_usage { DECLARE_PER_CPU(struct cpu_usage, cpu_usage_array); -#ifdef CONFIG_VIRT_CPU_ACCOUNTING -extern void account_process_vtime(struct task_struct *tsk); -#else -#define account_process_vtime(tsk) do { } while (0) -#endif - #if defined(CONFIG_VIRT_CPU_ACCOUNTING) extern void calculate_steal_time(void); extern void snapshot_timebases(void); +#define account_process_vtime(tsk) account_process_tick(tsk, 0) #else #define calculate_steal_time() do { } while (0) #define snapshot_timebases() do { } while (0) +#define account_process_vtime(tsk) do { } while (0) #endif extern void secondary_cpu_time_init(void); diff --git a/include/asm-x86/hpet.h b/include/asm-x86/hpet.h index b1f3c1ea55d9..ad8d6e758785 100644 --- a/include/asm-x86/hpet.h +++ b/include/asm-x86/hpet.h @@ -61,6 +61,7 @@ extern unsigned long force_hpet_address; extern int hpet_force_user; extern int is_hpet_enabled(void); extern int hpet_enable(void); +extern void hpet_disable(void); extern unsigned long hpet_readl(unsigned long a); extern void force_hpet_resume(void); diff --git a/include/linux/cgroup_subsys.h b/include/linux/cgroup_subsys.h index d62fcee9a08a..9ec43186ba80 100644 --- a/include/linux/cgroup_subsys.h +++ b/include/linux/cgroup_subsys.h @@ -30,3 +30,10 @@ SUBSYS(cpu_cgroup) #endif /* */ + +#ifdef CONFIG_CGROUP_CPUACCT +SUBSYS(cpuacct) +#endif + +/* */ + diff --git a/include/linux/if_bonding.h b/include/linux/if_bonding.h index 84598fa2e9de..65c2d247068b 100644 --- a/include/linux/if_bonding.h +++ b/include/linux/if_bonding.h @@ -85,7 +85,8 @@ /* hashing types */ #define BOND_XMIT_POLICY_LAYER2 0 /* layer 2 (MAC only), default */ -#define BOND_XMIT_POLICY_LAYER34 1 /* layer 3+4 (IP ^ MAC) */ +#define BOND_XMIT_POLICY_LAYER34 1 /* layer 3+4 (IP ^ (TCP || UDP)) */ +#define BOND_XMIT_POLICY_LAYER23 2 /* layer 2+3 (IP ^ MAC) */ typedef struct ifbond { __s32 bond_mode; diff --git a/include/linux/inet_lro.h b/include/linux/inet_lro.h index 1246d46abbc0..80335b7d77c5 100644 --- a/include/linux/inet_lro.h +++ b/include/linux/inet_lro.h @@ -91,6 +91,9 @@ struct net_lro_mgr { int max_desc; /* Max number of LRO descriptors */ int max_aggr; /* Max number of LRO packets to be aggregated */ + int frag_align_pad; /* Padding required to properly align layer 3 + * headers in generated skb when using frags */ + struct net_lro_desc *lro_arr; /* Array of LRO descriptors */ /* diff --git a/include/linux/jbd.h b/include/linux/jbd.h index 16e7ed855a18..d9ecd13393b0 100644 --- a/include/linux/jbd.h +++ b/include/linux/jbd.h @@ -439,6 +439,8 @@ struct transaction_s /* * Transaction's current state * [no locking - only kjournald alters this] + * [j_list_lock] guards transition of a transaction into T_FINISHED + * state and subsequent call of __journal_drop_transaction() * FIXME: needs barriers * KLUDGE: [use j_state_lock] */ diff --git a/include/linux/leds.h b/include/linux/leds.h index dc1178f6184b..b4130ff58d0c 100644 --- a/include/linux/leds.h +++ b/include/linux/leds.h @@ -14,6 +14,7 @@ #include <linux/list.h> #include <linux/spinlock.h> +#include <linux/rwsem.h> struct device; /* @@ -43,7 +44,7 @@ struct led_classdev { #ifdef CONFIG_LEDS_TRIGGERS /* Protects the trigger data below */ - rwlock_t trigger_lock; + struct rw_semaphore trigger_lock; struct led_trigger *trigger; struct list_head trig_list; diff --git a/include/linux/mm.h b/include/linux/mm.h index 520238cbae5d..1b7b95c67aca 100644 --- a/include/linux/mm.h +++ b/include/linux/mm.h @@ -12,6 +12,7 @@ #include <linux/prio_tree.h> #include <linux/debug_locks.h> #include <linux/mm_types.h> +#include <linux/security.h> struct mempolicy; struct anon_vma; @@ -513,6 +514,21 @@ static inline void set_page_links(struct page *page, enum zone_type zone, } /* + * If a hint addr is less than mmap_min_addr change hint to be as + * low as possible but still greater than mmap_min_addr + */ +static inline unsigned long round_hint_to_min(unsigned long hint) +{ +#ifdef CONFIG_SECURITY + hint &= PAGE_MASK; + if (((void *)hint != NULL) && + (hint < mmap_min_addr)) + return PAGE_ALIGN(mmap_min_addr); +#endif + return hint; +} + +/* * Some inline functions in vmstat.h depend on page_zone() */ #include <linux/vmstat.h> diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h index 1ee009e8fec8..111aa10f1136 100644 --- a/include/linux/pci_ids.h +++ b/include/linux/pci_ids.h @@ -1237,6 +1237,10 @@ #define PCI_DEVICE_ID_NVIDIA_NVENET_33 0x0761 #define PCI_DEVICE_ID_NVIDIA_NVENET_34 0x0762 #define PCI_DEVICE_ID_NVIDIA_NVENET_35 0x0763 +#define PCI_DEVICE_ID_NVIDIA_NVENET_36 0x0AB0 +#define PCI_DEVICE_ID_NVIDIA_NVENET_37 0x0AB1 +#define PCI_DEVICE_ID_NVIDIA_NVENET_38 0x0AB2 +#define PCI_DEVICE_ID_NVIDIA_NVENET_39 0x0AB3 #define PCI_VENDOR_ID_IMS 0x10e0 #define PCI_DEVICE_ID_IMS_TT128 0x9128 diff --git a/include/linux/phy.h b/include/linux/phy.h index f0742b6aaa64..554836edd915 100644 --- a/include/linux/phy.h +++ b/include/linux/phy.h @@ -58,6 +58,8 @@ typedef enum { PHY_INTERFACE_MODE_RMII, PHY_INTERFACE_MODE_RGMII, PHY_INTERFACE_MODE_RGMII_ID, + PHY_INTERFACE_MODE_RGMII_RXID, + PHY_INTERFACE_MODE_RGMII_TXID, PHY_INTERFACE_MODE_RTBI } phy_interface_t; @@ -401,6 +403,7 @@ int phy_mii_ioctl(struct phy_device *phydev, int phy_start_interrupts(struct phy_device *phydev); void phy_print_status(struct phy_device *phydev); struct phy_device* phy_device_create(struct mii_bus *bus, int addr, int phy_id); +void phy_device_free(struct phy_device *phydev); extern struct bus_type mdio_bus_type; #endif /* __PHY_H */ diff --git a/include/linux/proc_fs.h b/include/linux/proc_fs.h index 1273c6ec535c..a5316829215b 100644 --- a/include/linux/proc_fs.h +++ b/include/linux/proc_fs.h @@ -48,6 +48,8 @@ typedef int (read_proc_t)(char *page, char **start, off_t off, typedef int (write_proc_t)(struct file *file, const char __user *buffer, unsigned long count, void *data); typedef int (get_info_t)(char *, char **, off_t, int); +typedef struct proc_dir_entry *(shadow_proc_t)(struct task_struct *task, + struct proc_dir_entry *pde); struct proc_dir_entry { unsigned int low_ino; @@ -75,10 +77,10 @@ struct proc_dir_entry { read_proc_t *read_proc; write_proc_t *write_proc; atomic_t count; /* use count */ - int deleted; /* delete flag */ int pde_users; /* number of callers into module in progress */ spinlock_t pde_unload_lock; /* proc_fops checks and pde_users bumps */ struct completion *pde_unload_completion; + shadow_proc_t *shadow_proc; }; struct kcore_list { diff --git a/include/linux/thread_info.h b/include/linux/thread_info.h index 1c4eb41dbd89..9c4ad755d7e5 100644 --- a/include/linux/thread_info.h +++ b/include/linux/thread_info.h @@ -7,12 +7,25 @@ #ifndef _LINUX_THREAD_INFO_H #define _LINUX_THREAD_INFO_H +#include <linux/types.h> + /* - * System call restart block. + * System call restart block. */ struct restart_block { long (*fn)(struct restart_block *); - unsigned long arg0, arg1, arg2, arg3; + union { + struct { + unsigned long arg0, arg1, arg2, arg3; + }; + /* For futex_wait */ + struct { + u32 *uaddr; + u32 val; + u32 flags; + u64 time; + } futex; + }; }; extern long do_no_restart_syscall(struct restart_block *parm); diff --git a/include/net/route.h b/include/net/route.h index f7ce6259f86f..59b0b19205a2 100644 --- a/include/net/route.h +++ b/include/net/route.h @@ -109,7 +109,6 @@ struct in_device; extern int ip_rt_init(void); extern void ip_rt_redirect(__be32 old_gw, __be32 dst, __be32 new_gw, __be32 src, struct net_device *dev); -extern void ip_rt_advice(struct rtable **rp, int advice); extern void rt_cache_flush(int how); extern int __ip_route_output_key(struct rtable **, const struct flowi *flp); extern int ip_route_output_key(struct rtable **, struct flowi *flp); diff --git a/include/net/sctp/constants.h b/include/net/sctp/constants.h index f30b537d6952..05f22a6afbcd 100644 --- a/include/net/sctp/constants.h +++ b/include/net/sctp/constants.h @@ -441,11 +441,14 @@ enum { SCTP_AUTH_HMAC_ID_RESERVED_0, SCTP_AUTH_HMAC_ID_SHA1, SCTP_AUTH_HMAC_ID_RESERVED_2, - SCTP_AUTH_HMAC_ID_SHA256 +#if defined (CONFIG_CRYPTO_SHA256) || defined (CONFIG_CRYPTO_SHA256_MODULE) + SCTP_AUTH_HMAC_ID_SHA256, +#endif + __SCTP_AUTH_HMAC_MAX }; -#define SCTP_AUTH_HMAC_ID_MAX SCTP_AUTH_HMAC_ID_SHA256 -#define SCTP_AUTH_NUM_HMACS (SCTP_AUTH_HMAC_ID_SHA256 + 1) +#define SCTP_AUTH_HMAC_ID_MAX __SCTP_AUTH_HMAC_MAX - 1 +#define SCTP_AUTH_NUM_HMACS __SCTP_AUTH_HMAC_MAX #define SCTP_SHA1_SIG_SIZE 20 #define SCTP_SHA256_SIG_SIZE 32 diff --git a/include/net/sctp/structs.h b/include/net/sctp/structs.h index eb3113c38a94..002a00a4e6be 100644 --- a/include/net/sctp/structs.h +++ b/include/net/sctp/structs.h @@ -1184,6 +1184,9 @@ int sctp_bind_addr_copy(struct sctp_bind_addr *dest, const struct sctp_bind_addr *src, sctp_scope_t scope, gfp_t gfp, int flags); +int sctp_bind_addr_dup(struct sctp_bind_addr *dest, + const struct sctp_bind_addr *src, + gfp_t gfp); int sctp_add_bind_addr(struct sctp_bind_addr *, union sctp_addr *, __u8 use_as_src, gfp_t gfp); int sctp_del_bind_addr(struct sctp_bind_addr *, union sctp_addr *); diff --git a/init/Kconfig b/init/Kconfig index d35e44f4dd6b..404bbf3699be 100644 --- a/init/Kconfig +++ b/init/Kconfig @@ -354,6 +354,13 @@ config FAIR_CGROUP_SCHED endchoice +config CGROUP_CPUACCT + bool "Simple CPU accounting cgroup subsystem" + depends on CGROUPS + help + Provides a simple Resource Controller for monitoring the + total CPU consumed by the tasks in a cgroup + config SYSFS_DEPRECATED bool "Create deprecated sysfs files" default y diff --git a/init/do_mounts_initrd.c b/init/do_mounts_initrd.c index fd4fc12d2624..614241b5200c 100644 --- a/init/do_mounts_initrd.c +++ b/init/do_mounts_initrd.c @@ -55,12 +55,18 @@ static void __init handle_initrd(void) sys_mount(".", "/", NULL, MS_MOVE, NULL); sys_chroot("."); + /* + * In case that a resume from disk is carried out by linuxrc or one of + * its children, we need to tell the freezer not to wait for us. + */ + current->flags |= PF_FREEZER_SKIP; + pid = kernel_thread(do_linuxrc, "/linuxrc", SIGCHLD); if (pid > 0) - while (pid != sys_wait4(-1, NULL, 0, NULL)) { - try_to_freeze(); + while (pid != sys_wait4(-1, NULL, 0, NULL)) yield(); - } + + current->flags &= ~PF_FREEZER_SKIP; /* move initrd to rootfs' /old */ sys_fchdir(old_fd); diff --git a/kernel/Kconfig.instrumentation b/kernel/Kconfig.instrumentation index f5f2c769d95e..468f47ad7503 100644 --- a/kernel/Kconfig.instrumentation +++ b/kernel/Kconfig.instrumentation @@ -20,8 +20,8 @@ config PROFILING config OPROFILE tristate "OProfile system profiling (EXPERIMENTAL)" - depends on PROFILING - depends on ALPHA || ARM || BLACKFIN || X86_32 || IA64 || M32R || MIPS || PARISC || PPC || S390 || SUPERH || SPARC || X86_64 + depends on PROFILING && !UML + depends on ARCH_SUPPORTS_OPROFILE || ALPHA || ARM || BLACKFIN || IA64 || M32R || PARISC || PPC || S390 || SUPERH || SPARC help OProfile is a profiling system capable of profiling the whole system, include the kernel, kernel modules, libraries, @@ -31,7 +31,7 @@ config OPROFILE config KPROBES bool "Kprobes" - depends on KALLSYMS && MODULES + depends on KALLSYMS && MODULES && !UML depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32 help Kprobes allows you to trap at almost any kernel address and diff --git a/kernel/fork.c b/kernel/fork.c index 8ca1a14cdc8c..8dd8ff281009 100644 --- a/kernel/fork.c +++ b/kernel/fork.c @@ -1292,23 +1292,14 @@ static struct task_struct *copy_process(unsigned long clone_flags, __ptrace_link(p, current->parent); if (thread_group_leader(p)) { - if (clone_flags & CLONE_NEWPID) { + if (clone_flags & CLONE_NEWPID) p->nsproxy->pid_ns->child_reaper = p; - p->signal->tty = NULL; - set_task_pgrp(p, p->pid); - set_task_session(p, p->pid); - attach_pid(p, PIDTYPE_PGID, pid); - attach_pid(p, PIDTYPE_SID, pid); - } else { - p->signal->tty = current->signal->tty; - set_task_pgrp(p, task_pgrp_nr(current)); - set_task_session(p, task_session_nr(current)); - attach_pid(p, PIDTYPE_PGID, - task_pgrp(current)); - attach_pid(p, PIDTYPE_SID, - task_session(current)); - } + p->signal->tty = current->signal->tty; + set_task_pgrp(p, task_pgrp_nr(current)); + set_task_session(p, task_session_nr(current)); + attach_pid(p, PIDTYPE_PGID, task_pgrp(current)); + attach_pid(p, PIDTYPE_SID, task_session(current)); list_add_tail_rcu(&p->tasks, &init_task.tasks); __get_cpu_var(process_counts)++; } diff --git a/kernel/futex.c b/kernel/futex.c index 9dc591ab681a..172a1aeeafdb 100644 --- a/kernel/futex.c +++ b/kernel/futex.c @@ -658,7 +658,7 @@ static int wake_futex_pi(u32 __user *uaddr, u32 uval, struct futex_q *this) if (curval == -EFAULT) ret = -EFAULT; - if (curval != uval) + else if (curval != uval) ret = -EINVAL; if (ret) { spin_unlock(&pi_state->pi_mutex.wait_lock); @@ -1149,9 +1149,9 @@ static int fixup_pi_state_owner(u32 __user *uaddr, struct futex_q *q, /* * In case we must use restart_block to restart a futex_wait, - * we encode in the 'arg3' shared capability + * we encode in the 'flags' shared capability */ -#define ARG3_SHARED 1 +#define FLAGS_SHARED 1 static long futex_wait_restart(struct restart_block *restart); @@ -1290,12 +1290,13 @@ static int futex_wait(u32 __user *uaddr, struct rw_semaphore *fshared, struct restart_block *restart; restart = ¤t_thread_info()->restart_block; restart->fn = futex_wait_restart; - restart->arg0 = (unsigned long)uaddr; - restart->arg1 = (unsigned long)val; - restart->arg2 = (unsigned long)abs_time; - restart->arg3 = 0; + restart->futex.uaddr = (u32 *)uaddr; + restart->futex.val = val; + restart->futex.time = abs_time->tv64; + restart->futex.flags = 0; + if (fshared) - restart->arg3 |= ARG3_SHARED; + restart->futex.flags |= FLAGS_SHARED; return -ERESTART_RESTARTBLOCK; } @@ -1310,15 +1311,15 @@ static int futex_wait(u32 __user *uaddr, struct rw_semaphore *fshared, static long futex_wait_restart(struct restart_block *restart) { - u32 __user *uaddr = (u32 __user *)restart->arg0; - u32 val = (u32)restart->arg1; - ktime_t *abs_time = (ktime_t *)restart->arg2; + u32 __user *uaddr = (u32 __user *)restart->futex.uaddr; struct rw_semaphore *fshared = NULL; + ktime_t t; + t.tv64 = restart->futex.time; restart->fn = do_no_restart_syscall; - if (restart->arg3 & ARG3_SHARED) + if (restart->futex.flags & FLAGS_SHARED) fshared = ¤t->mm->mmap_sem; - return (long)futex_wait(uaddr, fshared, val, abs_time); + return (long)futex_wait(uaddr, fshared, restart->futex.val, &t); } diff --git a/kernel/hrtimer.c b/kernel/hrtimer.c index 22a25142e4cf..e65dd0b47cdc 100644 --- a/kernel/hrtimer.c +++ b/kernel/hrtimer.c @@ -850,6 +850,14 @@ hrtimer_start(struct hrtimer *timer, ktime_t tim, const enum hrtimer_mode mode) #ifdef CONFIG_TIME_LOW_RES tim = ktime_add(tim, base->resolution); #endif + /* + * Careful here: User space might have asked for a + * very long sleep, so the add above might result in a + * negative number, which enqueues the timer in front + * of the queue. + */ + if (tim.tv64 < 0) + tim.tv64 = KTIME_MAX; } timer->expires = tim; diff --git a/kernel/lockdep.c b/kernel/lockdep.c index ed38bbfc48a3..723bd9f92556 100644 --- a/kernel/lockdep.c +++ b/kernel/lockdep.c @@ -2654,10 +2654,15 @@ static void check_flags(unsigned long flags) if (!debug_locks) return; - if (irqs_disabled_flags(flags)) - DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled); - else - DEBUG_LOCKS_WARN_ON(!current->hardirqs_enabled); + if (irqs_disabled_flags(flags)) { + if (DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)) { + printk("possible reason: unannotated irqs-off.\n"); + } + } else { + if (DEBUG_LOCKS_WARN_ON(!current->hardirqs_enabled)) { + printk("possible reason: unannotated irqs-on.\n"); + } + } /* * We dont accurately track softirq state in e.g. @@ -3054,11 +3059,6 @@ void __init lockdep_info(void) #endif } -static inline int in_range(const void *start, const void *addr, const void *end) -{ - return addr >= start && addr <= end; -} - static void print_freed_lock_bug(struct task_struct *curr, const void *mem_from, const void *mem_to, struct held_lock *hlock) @@ -3080,6 +3080,13 @@ print_freed_lock_bug(struct task_struct *curr, const void *mem_from, dump_stack(); } +static inline int not_in_range(const void* mem_from, unsigned long mem_len, + const void* lock_from, unsigned long lock_len) +{ + return lock_from + lock_len <= mem_from || + mem_from + mem_len <= lock_from; +} + /* * Called when kernel memory is freed (or unmapped), or if a lock * is destroyed or reinitialized - this code checks whether there is @@ -3087,7 +3094,6 @@ print_freed_lock_bug(struct task_struct *curr, const void *mem_from, */ void debug_check_no_locks_freed(const void *mem_from, unsigned long mem_len) { - const void *mem_to = mem_from + mem_len, *lock_from, *lock_to; struct task_struct *curr = current; struct held_lock *hlock; unsigned long flags; @@ -3100,14 +3106,11 @@ void debug_check_no_locks_freed(const void *mem_from, unsigned long mem_len) for (i = 0; i < curr->lockdep_depth; i++) { hlock = curr->held_locks + i; - lock_from = (void *)hlock->instance; - lock_to = (void *)(hlock->instance + 1); - - if (!in_range(mem_from, lock_from, mem_to) && - !in_range(mem_from, lock_to, mem_to)) + if (not_in_range(mem_from, mem_len, hlock->instance, + sizeof(*hlock->instance))) continue; - print_freed_lock_bug(curr, mem_from, mem_to, hlock); + print_freed_lock_bug(curr, mem_from, mem_from + mem_len, hlock); break; } local_irq_restore(flags); @@ -3173,6 +3176,13 @@ retry: printk(" locked it.\n"); do_each_thread(g, p) { + /* + * It's not reliable to print a task's held locks + * if it's not sleeping (or if it's not the current + * task): + */ + if (p->state == TASK_RUNNING && p != current) + continue; if (p->lockdep_depth) lockdep_print_held_locks(p); if (!unlock) diff --git a/kernel/sched.c b/kernel/sched.c index 98dcdf272db3..c6e551de795b 100644 --- a/kernel/sched.c +++ b/kernel/sched.c @@ -209,9 +209,8 @@ static inline struct task_group *task_group(struct task_struct *p) tg = container_of(task_subsys_state(p, cpu_cgroup_subsys_id), struct task_group, css); #else - tg = &init_task_group; + tg = &init_task_group; #endif - return tg; } @@ -249,15 +248,16 @@ struct cfs_rq { #ifdef CONFIG_FAIR_GROUP_SCHED struct rq *rq; /* cpu runqueue to which this cfs_rq is attached */ - /* leaf cfs_rqs are those that hold tasks (lowest schedulable entity in + /* + * leaf cfs_rqs are those that hold tasks (lowest schedulable entity in * a hierarchy). Non-leaf lrqs hold other higher schedulable entities * (like users, containers etc.) * * leaf_cfs_rq_list ties together list of leaf cfs_rq's in a cpu. This * list is used during load balance. */ - struct list_head leaf_cfs_rq_list; /* Better name : task_cfs_rq_list? */ - struct task_group *tg; /* group that "owns" this runqueue */ + struct list_head leaf_cfs_rq_list; + struct task_group *tg; /* group that "owns" this runqueue */ #endif }; @@ -300,7 +300,7 @@ struct rq { /* list of leaf cfs_rq on this cpu: */ struct list_head leaf_cfs_rq_list; #endif - struct rt_rq rt; + struct rt_rq rt; /* * This is part of a global counter where only the total sum @@ -457,8 +457,8 @@ enum { SCHED_FEAT_NEW_FAIR_SLEEPERS = 1, SCHED_FEAT_WAKEUP_PREEMPT = 2, SCHED_FEAT_START_DEBIT = 4, - SCHED_FEAT_TREE_AVG = 8, - SCHED_FEAT_APPROX_AVG = 16, + SCHED_FEAT_TREE_AVG = 8, + SCHED_FEAT_APPROX_AVG = 16, }; const_debug unsigned int sysctl_sched_features = @@ -488,7 +488,12 @@ unsigned long long cpu_clock(int cpu) local_irq_save(flags); rq = cpu_rq(cpu); - update_rq_clock(rq); + /* + * Only call sched_clock() if the scheduler has already been + * initialized (some code might call cpu_clock() very early): + */ + if (rq->idle) + update_rq_clock(rq); now = rq->clock; local_irq_restore(flags); @@ -591,7 +596,7 @@ static inline struct rq *__task_rq_lock(struct task_struct *p) /* * task_rq_lock - lock the runqueue a given task resides on and disable - * interrupts. Note the ordering: we can safely lookup the task_rq without + * interrupts. Note the ordering: we can safely lookup the task_rq without * explicitly disabling preemption. */ static struct rq *task_rq_lock(struct task_struct *p, unsigned long *flags) @@ -779,7 +784,7 @@ static inline void update_load_sub(struct load_weight *lw, unsigned long dec) * To aid in avoiding the subversion of "niceness" due to uneven distribution * of tasks with abnormal "nice" values across CPUs the contribution that * each task makes to its run queue's load is weighted according to its - * scheduling class and "nice" value. For SCHED_NORMAL tasks this is just a + * scheduling class and "nice" value. For SCHED_NORMAL tasks this is just a * scaled version of the new time slice allocation that they receive on time * slice expiry etc. */ @@ -854,6 +859,12 @@ iter_move_one_task(struct rq *this_rq, int this_cpu, struct rq *busiest, struct rq_iterator *iterator); #endif +#ifdef CONFIG_CGROUP_CPUACCT +static void cpuacct_charge(struct task_struct *tsk, u64 cputime); +#else +static inline void cpuacct_charge(struct task_struct *tsk, u64 cputime) {} +#endif + #include "sched_stats.h" #include "sched_idletask.c" #include "sched_fair.c" @@ -1848,7 +1859,7 @@ prepare_task_switch(struct rq *rq, struct task_struct *prev, * and do any other architecture-specific cleanup actions. * * Note that we may have delayed dropping an mm in context_switch(). If - * so, we finish that here outside of the runqueue lock. (Doing it + * so, we finish that here outside of the runqueue lock. (Doing it * with the lock held can cause deadlocks; see schedule() for * details.) */ @@ -2130,7 +2141,7 @@ static void double_lock_balance(struct rq *this_rq, struct rq *busiest) /* * If dest_cpu is allowed for this process, migrate the task to it. * This is accomplished by forcing the cpu_allowed mask to only - * allow dest_cpu, which will force the cpu onto dest_cpu. Then + * allow dest_cpu, which will force the cpu onto dest_cpu. Then * the cpu_allowed mask is restored. */ static void sched_migrate_task(struct task_struct *p, int dest_cpu) @@ -2575,7 +2586,7 @@ group_next: * tasks around. Thus we look for the minimum possible imbalance. * Negative imbalances (*we* are more loaded than anyone else) will * be counted as no imbalance for these purposes -- we can't fix that - * by pulling tasks to us. Be careful of negative numbers as they'll + * by pulling tasks to us. Be careful of negative numbers as they'll * appear as very large values with unsigned longs. */ if (max_load <= busiest_load_per_task) @@ -3010,7 +3021,7 @@ static void active_load_balance(struct rq *busiest_rq, int busiest_cpu) /* * This condition is "impossible", if it occurs - * we need to fix it. Originally reported by + * we need to fix it. Originally reported by * Bjorn Helgaas on a 128-cpu setup. */ BUG_ON(busiest_rq == target_rq); @@ -3042,7 +3053,7 @@ static void active_load_balance(struct rq *busiest_rq, int busiest_cpu) #ifdef CONFIG_NO_HZ static struct { atomic_t load_balancer; - cpumask_t cpu_mask; + cpumask_t cpu_mask; } nohz ____cacheline_aligned = { .load_balancer = ATOMIC_INIT(-1), .cpu_mask = CPU_MASK_NONE, @@ -3546,7 +3557,7 @@ static noinline void __schedule_bug(struct task_struct *prev) static inline void schedule_debug(struct task_struct *prev) { /* - * Test if we are atomic. Since do_exit() needs to call into + * Test if we are atomic. Since do_exit() needs to call into * schedule() atomically, we ignore that path for now. * Otherwise, whine if we are scheduling when we should not be. */ @@ -3668,7 +3679,7 @@ EXPORT_SYMBOL(schedule); #ifdef CONFIG_PREEMPT /* * this is the entry point to schedule() from in-kernel preemption - * off of preempt_enable. Kernel preemptions off return from interrupt + * off of preempt_enable. Kernel preemptions off return from interrupt * occur there and call schedule directly. */ asmlinkage void __sched preempt_schedule(void) @@ -3680,7 +3691,7 @@ asmlinkage void __sched preempt_schedule(void) #endif /* * If there is a non-zero preempt_count or interrupts are disabled, - * we do not want to preempt the current task. Just return.. + * we do not want to preempt the current task. Just return.. */ if (likely(ti->preempt_count || irqs_disabled())) return; @@ -3766,12 +3777,12 @@ int default_wake_function(wait_queue_t *curr, unsigned mode, int sync, EXPORT_SYMBOL(default_wake_function); /* - * The core wakeup function. Non-exclusive wakeups (nr_exclusive == 0) just - * wake everything up. If it's an exclusive wakeup (nr_exclusive == small +ve + * The core wakeup function. Non-exclusive wakeups (nr_exclusive == 0) just + * wake everything up. If it's an exclusive wakeup (nr_exclusive == small +ve * number) then we wake all the non-exclusive tasks and one exclusive task. * * There are circumstances in which we can try to wake a task which has already - * started to run but is not in state TASK_RUNNING. try_to_wake_up() returns + * started to run but is not in state TASK_RUNNING. try_to_wake_up() returns * zero in this (rare) case, and we handle it by continuing to scan the queue. */ static void __wake_up_common(wait_queue_head_t *q, unsigned int mode, @@ -4384,8 +4395,8 @@ do_sched_setscheduler(pid_t pid, int policy, struct sched_param __user *param) * @policy: new policy. * @param: structure containing the new RT priority. */ -asmlinkage long sys_sched_setscheduler(pid_t pid, int policy, - struct sched_param __user *param) +asmlinkage long +sys_sched_setscheduler(pid_t pid, int policy, struct sched_param __user *param) { /* negative values for policy are not valid */ if (policy < 0) @@ -4485,7 +4496,7 @@ long sched_setaffinity(pid_t pid, cpumask_t new_mask) /* * It is not safe to call set_cpus_allowed with the - * tasklist_lock held. We will bump the task_struct's + * tasklist_lock held. We will bump the task_struct's * usage count and then drop tasklist_lock. */ get_task_struct(p); @@ -4681,7 +4692,7 @@ EXPORT_SYMBOL(cond_resched); * cond_resched_lock() - if a reschedule is pending, drop the given lock, * call schedule, and on return reacquire the lock. * - * This works OK both with and without CONFIG_PREEMPT. We do strange low-level + * This works OK both with and without CONFIG_PREEMPT. We do strange low-level * operations here to prevent schedule() from being called twice (once via * spin_unlock(), once by hand). */ @@ -4735,7 +4746,7 @@ void __sched yield(void) EXPORT_SYMBOL(yield); /* - * This task is about to go to sleep on IO. Increment rq->nr_iowait so + * This task is about to go to sleep on IO. Increment rq->nr_iowait so * that process accounting knows that this is a task in IO wait state. * * But don't do that if it is a deliberate, throttling IO wait (this task @@ -4844,17 +4855,21 @@ long sys_sched_rr_get_interval(pid_t pid, struct timespec __user *interval) if (retval) goto out_unlock; - if (p->policy == SCHED_FIFO) - time_slice = 0; - else if (p->policy == SCHED_RR) + /* + * Time slice is 0 for SCHED_FIFO tasks and for SCHED_OTHER + * tasks that are on an otherwise idle runqueue: + */ + time_slice = 0; + if (p->policy == SCHED_RR) { time_slice = DEF_TIMESLICE; - else { + } else { struct sched_entity *se = &p->se; unsigned long flags; struct rq *rq; rq = task_rq_lock(p, &flags); - time_slice = NS_TO_JIFFIES(sched_slice(cfs_rq_of(se), se)); + if (rq->cfs.load.weight) + time_slice = NS_TO_JIFFIES(sched_slice(&rq->cfs, se)); task_rq_unlock(rq, &flags); } read_unlock(&tasklist_lock); @@ -5040,7 +5055,7 @@ static inline void sched_init_granularity(void) * is removed from the allowed bitmask. * * NOTE: the caller must have a valid reference to the task, the - * task must not exit() & deallocate itself prematurely. The + * task must not exit() & deallocate itself prematurely. The * call is not atomic; no spinlocks may be held. */ int set_cpus_allowed(struct task_struct *p, cpumask_t new_mask) @@ -5077,7 +5092,7 @@ out: EXPORT_SYMBOL_GPL(set_cpus_allowed); /* - * Move (not current) task off this cpu, onto dest cpu. We're doing + * Move (not current) task off this cpu, onto dest cpu. We're doing * this because either it can't run here any more (set_cpus_allowed() * away from this CPU, or CPU going down), or because we're * attempting to rebalance this task on exec (sched_exec). @@ -5222,7 +5237,7 @@ static void move_task_off_dead_cpu(int dead_cpu, struct task_struct *p) * Try to stay on the same cpuset, where the * current cpuset may be a subset of all cpus. * The cpuset_cpus_allowed_locked() variant of - * cpuset_cpus_allowed() will not block. It must be + * cpuset_cpus_allowed() will not block. It must be * called within calls to cpuset_lock/cpuset_unlock. */ rq = task_rq_lock(p, &flags); @@ -5235,10 +5250,11 @@ static void move_task_off_dead_cpu(int dead_cpu, struct task_struct *p) * kernel threads (both mm NULL), since they never * leave kernel. */ - if (p->mm && printk_ratelimit()) + if (p->mm && printk_ratelimit()) { printk(KERN_INFO "process %d (%s) no " "longer affine to cpu%d\n", - task_pid_nr(p), p->comm, dead_cpu); + task_pid_nr(p), p->comm, dead_cpu); + } } } while (!__migrate_task_irq(p, dead_cpu, dest_cpu)); } @@ -5340,7 +5356,7 @@ static void migrate_dead(unsigned int dead_cpu, struct task_struct *p) /* * Drop lock around migration; if someone else moves it, - * that's OK. No task can be added to this CPU, so iteration is + * that's OK. No task can be added to this CPU, so iteration is * fine. */ spin_unlock_irq(&rq->lock); @@ -5404,7 +5420,7 @@ static void sd_free_ctl_entry(struct ctl_table **tablep) /* * In the intermediate directories, both the child directory and * procname are dynamically allocated and could fail but the mode - * will always be set. In the lowest directory the names are + * will always be set. In the lowest directory the names are * static strings and all have proc handlers. */ for (entry = *tablep; entry->mode; entry++) { @@ -5575,7 +5591,7 @@ migration_call(struct notifier_block *nfb, unsigned long action, void *hcpu) case CPU_UP_CANCELED_FROZEN: if (!cpu_rq(cpu)->migration_thread) break; - /* Unbind it from offline cpu so it can run. Fall thru. */ + /* Unbind it from offline cpu so it can run. Fall thru. */ kthread_bind(cpu_rq(cpu)->migration_thread, any_online_cpu(cpu_online_map)); kthread_stop(cpu_rq(cpu)->migration_thread); @@ -5602,9 +5618,11 @@ migration_call(struct notifier_block *nfb, unsigned long action, void *hcpu) migrate_nr_uninterruptible(rq); BUG_ON(rq->nr_running != 0); - /* No need to migrate the tasks: it was best-effort if - * they didn't take sched_hotcpu_mutex. Just wake up - * the requestors. */ + /* + * No need to migrate the tasks: it was best-effort if + * they didn't take sched_hotcpu_mutex. Just wake up + * the requestors. + */ spin_lock_irq(&rq->lock); while (!list_empty(&rq->migration_queue)) { struct migration_req *req; @@ -5912,7 +5930,7 @@ init_sched_build_groups(cpumask_t span, const cpumask_t *cpu_map, * @node: node whose sched_domain we're building * @used_nodes: nodes already in the sched_domain * - * Find the next node to include in a given scheduling domain. Simply + * Find the next node to include in a given scheduling domain. Simply * finds the closest node not already in the @used_nodes map. * * Should use nodemask_t. @@ -5952,7 +5970,7 @@ static int find_next_best_node(int node, unsigned long *used_nodes) * @node: node whose cpumask we're constructing * @size: number of nodes to include in this span * - * Given a node, construct a good cpumask for its sched_domain to span. It + * Given a node, construct a good cpumask for its sched_domain to span. It * should be one that prevents unnecessary balancing, but also spreads tasks * out optimally. */ @@ -5989,8 +6007,8 @@ int sched_smt_power_savings = 0, sched_mc_power_savings = 0; static DEFINE_PER_CPU(struct sched_domain, cpu_domains); static DEFINE_PER_CPU(struct sched_group, sched_group_cpus); -static int cpu_to_cpu_group(int cpu, const cpumask_t *cpu_map, - struct sched_group **sg) +static int +cpu_to_cpu_group(int cpu, const cpumask_t *cpu_map, struct sched_group **sg) { if (sg) *sg = &per_cpu(sched_group_cpus, cpu); @@ -6007,8 +6025,8 @@ static DEFINE_PER_CPU(struct sched_group, sched_group_core); #endif #if defined(CONFIG_SCHED_MC) && defined(CONFIG_SCHED_SMT) -static int cpu_to_core_group(int cpu, const cpumask_t *cpu_map, - struct sched_group **sg) +static int +cpu_to_core_group(int cpu, const cpumask_t *cpu_map, struct sched_group **sg) { int group; cpumask_t mask = per_cpu(cpu_sibling_map, cpu); @@ -6019,8 +6037,8 @@ static int cpu_to_core_group(int cpu, const cpumask_t *cpu_map, return group; } #elif defined(CONFIG_SCHED_MC) -static int cpu_to_core_group(int cpu, const cpumask_t *cpu_map, - struct sched_group **sg) +static int +cpu_to_core_group(int cpu, const cpumask_t *cpu_map, struct sched_group **sg) { if (sg) *sg = &per_cpu(sched_group_core, cpu); @@ -6031,8 +6049,8 @@ static int cpu_to_core_group(int cpu, const cpumask_t *cpu_map, static DEFINE_PER_CPU(struct sched_domain, phys_domains); static DEFINE_PER_CPU(struct sched_group, sched_group_phys); -static int cpu_to_phys_group(int cpu, const cpumask_t *cpu_map, - struct sched_group **sg) +static int +cpu_to_phys_group(int cpu, const cpumask_t *cpu_map, struct sched_group **sg) { int group; #ifdef CONFIG_SCHED_MC @@ -6212,7 +6230,7 @@ static int build_sched_domains(const cpumask_t *cpu_map) * Allocate the per-node list of sched groups */ sched_group_nodes = kcalloc(MAX_NUMNODES, sizeof(struct sched_group *), - GFP_KERNEL); + GFP_KERNEL); if (!sched_group_nodes) { printk(KERN_WARNING "Can not alloc sched group node list\n"); return -ENOMEM; @@ -6459,7 +6477,7 @@ static int ndoms_cur; /* number of sched domains in 'doms_cur' */ static cpumask_t fallback_doms; /* - * Set up scheduler domains and groups. Callers must hold the hotplug lock. + * Set up scheduler domains and groups. Callers must hold the hotplug lock. * For now this just excludes isolated cpus, but could be used to * exclude other special cases in the future. */ @@ -6501,19 +6519,19 @@ static void detach_destroy_domains(const cpumask_t *cpu_map) /* * Partition sched domains as specified by the 'ndoms_new' - * cpumasks in the array doms_new[] of cpumasks. This compares + * cpumasks in the array doms_new[] of cpumasks. This compares * doms_new[] to the current sched domain partitioning, doms_cur[]. * It destroys each deleted domain and builds each new domain. * * 'doms_new' is an array of cpumask_t's of length 'ndoms_new'. - * The masks don't intersect (don't overlap.) We should setup one - * sched domain for each mask. CPUs not in any of the cpumasks will - * not be load balanced. If the same cpumask appears both in the + * The masks don't intersect (don't overlap.) We should setup one + * sched domain for each mask. CPUs not in any of the cpumasks will + * not be load balanced. If the same cpumask appears both in the * current 'doms_cur' domains and in the new 'doms_new', we can leave * it as it is. * - * The passed in 'doms_new' should be kmalloc'd. This routine takes - * ownership of it and will kfree it when done with it. If the caller + * The passed in 'doms_new' should be kmalloc'd. This routine takes + * ownership of it and will kfree it when done with it. If the caller * failed the kmalloc call, then it can pass in doms_new == NULL, * and partition_sched_domains() will fallback to the single partition * 'fallback_doms'. @@ -6643,7 +6661,7 @@ int sched_create_sysfs_power_savings_entries(struct sysdev_class *cls) #endif /* - * Force a reinitialization of the sched domains hierarchy. The domains + * Force a reinitialization of the sched domains hierarchy. The domains * and groups cannot be updated in place without racing with the balancing * code, so we temporarily attach all running cpus to the NULL domain * which will prevent rebalancing while the sched domains are recalculated. @@ -6933,8 +6951,8 @@ struct task_struct *curr_task(int cpu) * @p: the task pointer to set. * * Description: This function must only be used when non-maskable interrupts - * are serviced on a separate stack. It allows the architecture to switch the - * notion of the current task on a cpu in a non-blocking manner. This function + * are serviced on a separate stack. It allows the architecture to switch the + * notion of the current task on a cpu in a non-blocking manner. This function * must be called with all CPU's synchronized, and interrupts disabled, the * and caller must save the original value of the current task (see * curr_task() above) and restore that value before reenabling interrupts and @@ -7183,16 +7201,17 @@ cpu_cgroup_create(struct cgroup_subsys *ss, struct cgroup *cgrp) return &tg->css; } -static void cpu_cgroup_destroy(struct cgroup_subsys *ss, - struct cgroup *cgrp) +static void +cpu_cgroup_destroy(struct cgroup_subsys *ss, struct cgroup *cgrp) { struct task_group *tg = cgroup_tg(cgrp); sched_destroy_group(tg); } -static int cpu_cgroup_can_attach(struct cgroup_subsys *ss, - struct cgroup *cgrp, struct task_struct *tsk) +static int +cpu_cgroup_can_attach(struct cgroup_subsys *ss, struct cgroup *cgrp, + struct task_struct *tsk) { /* We don't support RT-tasks being in separate groups */ if (tsk->sched_class != &fair_sched_class) @@ -7221,38 +7240,12 @@ static u64 cpu_shares_read_uint(struct cgroup *cgrp, struct cftype *cft) return (u64) tg->shares; } -static u64 cpu_usage_read(struct cgroup *cgrp, struct cftype *cft) -{ - struct task_group *tg = cgroup_tg(cgrp); - unsigned long flags; - u64 res = 0; - int i; - - for_each_possible_cpu(i) { - /* - * Lock to prevent races with updating 64-bit counters - * on 32-bit arches. - */ - spin_lock_irqsave(&cpu_rq(i)->lock, flags); - res += tg->se[i]->sum_exec_runtime; - spin_unlock_irqrestore(&cpu_rq(i)->lock, flags); - } - /* Convert from ns to ms */ - do_div(res, NSEC_PER_MSEC); - - return res; -} - static struct cftype cpu_files[] = { { .name = "shares", .read_uint = cpu_shares_read_uint, .write_uint = cpu_shares_write_uint, }, - { - .name = "usage", - .read_uint = cpu_usage_read, - }, }; static int cpu_cgroup_populate(struct cgroup_subsys *ss, struct cgroup *cont) @@ -7272,3 +7265,126 @@ struct cgroup_subsys cpu_cgroup_subsys = { }; #endif /* CONFIG_FAIR_CGROUP_SCHED */ + +#ifdef CONFIG_CGROUP_CPUACCT + +/* + * CPU accounting code for task groups. + * + * Based on the work by Paul Menage (menage@google.com) and Balbir Singh + * (balbir@in.ibm.com). + */ + +/* track cpu usage of a group of tasks */ +struct cpuacct { + struct cgroup_subsys_state css; + /* cpuusage holds pointer to a u64-type object on every cpu */ + u64 *cpuusage; +}; + +struct cgroup_subsys cpuacct_subsys; + +/* return cpu accounting group corresponding to this container */ +static inline struct cpuacct *cgroup_ca(struct cgroup *cont) +{ + return container_of(cgroup_subsys_state(cont, cpuacct_subsys_id), + struct cpuacct, css); +} + +/* return cpu accounting group to which this task belongs */ +static inline struct cpuacct *task_ca(struct task_struct *tsk) +{ + return container_of(task_subsys_state(tsk, cpuacct_subsys_id), + struct cpuacct, css); +} + +/* create a new cpu accounting group */ +static struct cgroup_subsys_state *cpuacct_create( + struct cgroup_subsys *ss, struct cgroup *cont) +{ + struct cpuacct *ca = kzalloc(sizeof(*ca), GFP_KERNEL); + + if (!ca) + return ERR_PTR(-ENOMEM); + + ca->cpuusage = alloc_percpu(u64); + if (!ca->cpuusage) { + kfree(ca); + return ERR_PTR(-ENOMEM); + } + + return &ca->css; +} + +/* destroy an existing cpu accounting group */ +static void +cpuacct_destroy(struct cgroup_subsys *ss, struct cgroup *cont) +{ + struct cpuacct *ca = cgroup_ca(cont); + + free_percpu(ca->cpuusage); + kfree(ca); +} + +/* return total cpu usage (in nanoseconds) of a group */ +static u64 cpuusage_read(struct cgroup *cont, struct cftype *cft) +{ + struct cpuacct *ca = cgroup_ca(cont); + u64 totalcpuusage = 0; + int i; + + for_each_possible_cpu(i) { + u64 *cpuusage = percpu_ptr(ca->cpuusage, i); + + /* + * Take rq->lock to make 64-bit addition safe on 32-bit + * platforms. + */ + spin_lock_irq(&cpu_rq(i)->lock); + totalcpuusage += *cpuusage; + spin_unlock_irq(&cpu_rq(i)->lock); + } + + return totalcpuusage; +} + +static struct cftype files[] = { + { + .name = "usage", + .read_uint = cpuusage_read, + }, +}; + +static int cpuacct_populate(struct cgroup_subsys *ss, struct cgroup *cont) +{ + return cgroup_add_files(cont, ss, files, ARRAY_SIZE(files)); +} + +/* + * charge this task's execution time to its accounting group. + * + * called with rq->lock held. + */ +static void cpuacct_charge(struct task_struct *tsk, u64 cputime) +{ + struct cpuacct *ca; + + if (!cpuacct_subsys.active) + return; + + ca = task_ca(tsk); + if (ca) { + u64 *cpuusage = percpu_ptr(ca->cpuusage, task_cpu(tsk)); + + *cpuusage += cputime; + } +} + +struct cgroup_subsys cpuacct_subsys = { + .name = "cpuacct", + .create = cpuacct_create, + .destroy = cpuacct_destroy, + .populate = cpuacct_populate, + .subsys_id = cpuacct_subsys_id, +}; +#endif /* CONFIG_CGROUP_CPUACCT */ diff --git a/kernel/sched_fair.c b/kernel/sched_fair.c index 2f16e15c022c..c33f0ceb3de9 100644 --- a/kernel/sched_fair.c +++ b/kernel/sched_fair.c @@ -351,6 +351,12 @@ static void update_curr(struct cfs_rq *cfs_rq) __update_curr(cfs_rq, curr, delta_exec); curr->exec_start = now; + + if (entity_is_task(curr)) { + struct task_struct *curtask = task_of(curr); + + cpuacct_charge(curtask, delta_exec); + } } static inline void @@ -793,8 +799,9 @@ static void dequeue_task_fair(struct rq *rq, struct task_struct *p, int sleep) */ static void yield_task_fair(struct rq *rq) { - struct cfs_rq *cfs_rq = task_cfs_rq(rq->curr); - struct sched_entity *rightmost, *se = &rq->curr->se; + struct task_struct *curr = rq->curr; + struct cfs_rq *cfs_rq = task_cfs_rq(curr); + struct sched_entity *rightmost, *se = &curr->se; /* * Are we the only task in the tree? @@ -802,7 +809,7 @@ static void yield_task_fair(struct rq *rq) if (unlikely(cfs_rq->nr_running == 1)) return; - if (likely(!sysctl_sched_compat_yield)) { + if (likely(!sysctl_sched_compat_yield) && curr->policy != SCHED_BATCH) { __update_rq_clock(rq); /* * Update run-time statistics of the 'current'. diff --git a/kernel/sched_rt.c b/kernel/sched_rt.c index 8abd752a0ebd..ee9c8b6529e9 100644 --- a/kernel/sched_rt.c +++ b/kernel/sched_rt.c @@ -23,6 +23,7 @@ static void update_curr_rt(struct rq *rq) curr->se.sum_exec_runtime += delta_exec; curr->se.exec_start = rq->clock; + cpuacct_charge(curr, delta_exec); } static void enqueue_task_rt(struct rq *rq, struct task_struct *p, int wakeup) diff --git a/kernel/sysctl.c b/kernel/sysctl.c index 0deed82a6156..8ac51714b08c 100644 --- a/kernel/sysctl.c +++ b/kernel/sysctl.c @@ -1588,6 +1588,10 @@ struct ctl_table_header *register_sysctl_table(struct ctl_table * table) void unregister_sysctl_table(struct ctl_table_header * header) { might_sleep(); + + if (header == NULL) + return; + spin_lock(&sysctl_lock); start_unregistering(header); spin_unlock(&sysctl_lock); diff --git a/kernel/sysctl_check.c b/kernel/sysctl_check.c index 6972f26c65f7..bed939f82c31 100644 --- a/kernel/sysctl_check.c +++ b/kernel/sysctl_check.c @@ -96,7 +96,7 @@ static struct trans_ctl_table trans_kern_table[] = { { KERN_PTY, "pty", trans_pty_table }, { KERN_NGROUPS_MAX, "ngroups_max" }, - { KERN_SPARC_SCONS_PWROFF, "scons_poweroff" }, + { KERN_SPARC_SCONS_PWROFF, "scons-poweroff" }, { KERN_HZ_TIMER, "hz_timer" }, { KERN_UNKNOWN_NMI_PANIC, "unknown_nmi_panic" }, { KERN_BOOTLOADER_TYPE, "bootloader_type" }, diff --git a/kernel/time/clockevents.c b/kernel/time/clockevents.c index 822beebe664a..5fb139fef9fa 100644 --- a/kernel/time/clockevents.c +++ b/kernel/time/clockevents.c @@ -78,6 +78,11 @@ int clockevents_program_event(struct clock_event_device *dev, ktime_t expires, unsigned long long clc; int64_t delta; + if (unlikely(expires.tv64 < 0)) { + WARN_ON_ONCE(1); + return -ETIME; + } + delta = ktime_to_ns(ktime_sub(expires, now)); if (delta <= 0) diff --git a/lib/textsearch.c b/lib/textsearch.c index 88c98a2ec8d9..be8bda3862f5 100644 --- a/lib/textsearch.c +++ b/lib/textsearch.c @@ -7,7 +7,7 @@ * 2 of the License, or (at your option) any later version. * * Authors: Thomas Graf <tgraf@suug.ch> - * Pablo Neira Ayuso <pablo@eurodev.net> + * Pablo Neira Ayuso <pablo@netfilter.org> * * ========================================================================== * @@ -250,7 +250,8 @@ unsigned int textsearch_find_continuous(struct ts_config *conf, * the various search algorithms. * * Returns a new textsearch configuration according to the specified - * parameters or a ERR_PTR(). + * parameters or a ERR_PTR(). If a zero length pattern is passed, this + * function returns EINVAL. */ struct ts_config *textsearch_prepare(const char *algo, const void *pattern, unsigned int len, gfp_t gfp_mask, int flags) @@ -259,6 +260,9 @@ struct ts_config *textsearch_prepare(const char *algo, const void *pattern, struct ts_config *conf; struct ts_ops *ops; + if (len == 0) + return ERR_PTR(-EINVAL); + ops = lookup_ts_algo(algo); #ifdef CONFIG_KMOD /* diff --git a/mm/backing-dev.c b/mm/backing-dev.c index b0ceb29da4c7..e8644b1e5527 100644 --- a/mm/backing-dev.c +++ b/mm/backing-dev.c @@ -7,7 +7,7 @@ int bdi_init(struct backing_dev_info *bdi) { - int i, j; + int i; int err; for (i = 0; i < NR_BDI_STAT_ITEMS; i++) { @@ -21,7 +21,7 @@ int bdi_init(struct backing_dev_info *bdi) if (err) { err: - for (j = 0; j < i; j++) + while (i--) percpu_counter_destroy(&bdi->bdi_stat[i]); } diff --git a/mm/filemap_xip.c b/mm/filemap_xip.c index 32132f3cd641..e233fff61b4b 100644 --- a/mm/filemap_xip.c +++ b/mm/filemap_xip.c @@ -314,7 +314,7 @@ __xip_file_write(struct file *filp, const char __user *buf, fault_in_pages_readable(buf, bytes); kaddr = kmap_atomic(page, KM_USER0); copied = bytes - - __copy_from_user_inatomic_nocache(kaddr, buf, bytes); + __copy_from_user_inatomic_nocache(kaddr + offset, buf, bytes); kunmap_atomic(kaddr, KM_USER0); flush_dcache_page(page); diff --git a/mm/mmap.c b/mm/mmap.c index facc1a75bd4f..15678aa6ec73 100644 --- a/mm/mmap.c +++ b/mm/mmap.c @@ -912,6 +912,9 @@ unsigned long do_mmap_pgoff(struct file * file, unsigned long addr, if (!len) return -EINVAL; + if (!(flags & MAP_FIXED)) + addr = round_hint_to_min(addr); + error = arch_mmap_check(addr, len, flags); if (error) return error; @@ -1615,6 +1618,12 @@ static inline int expand_downwards(struct vm_area_struct *vma, */ if (unlikely(anon_vma_prepare(vma))) return -ENOMEM; + + address &= PAGE_MASK; + error = security_file_mmap(0, 0, 0, 0, address, 1); + if (error) + return error; + anon_vma_lock(vma); /* @@ -1622,8 +1631,6 @@ static inline int expand_downwards(struct vm_area_struct *vma, * is required to hold the mmap_sem in read mode. We need the * anon_vma lock to serialize against concurrent expand_stacks. */ - address &= PAGE_MASK; - error = 0; /* Somebody else might have raced and expanded it already */ if (address < vma->vm_start) { @@ -1934,6 +1941,10 @@ unsigned long do_brk(unsigned long addr, unsigned long len) if (is_hugepage_only_range(mm, addr, len)) return -EINVAL; + error = security_file_mmap(0, 0, 0, 0, addr, 1); + if (error) + return error; + flags = VM_DATA_DEFAULT_FLAGS | VM_ACCOUNT | mm->def_flags; error = arch_mmap_check(addr, len, flags); diff --git a/mm/nommu.c b/mm/nommu.c index 35622c590925..b989cb928a7c 100644 --- a/mm/nommu.c +++ b/mm/nommu.c @@ -829,6 +829,9 @@ unsigned long do_mmap_pgoff(struct file *file, void *result; int ret; + if (!(flags & MAP_FIXED)) + addr = round_hint_to_min(addr); + /* decide whether we should attempt the mapping, and if so what sort of * mapping */ ret = validate_mmap_request(file, addr, len, prot, flags, pgoff, diff --git a/mm/slab.c b/mm/slab.c index 202465a193c1..2e338a5f7b14 100644 --- a/mm/slab.c +++ b/mm/slab.c @@ -4475,3 +4475,4 @@ size_t ksize(const void *objp) return obj_size(virt_to_cache(objp)); } +EXPORT_SYMBOL(ksize); diff --git a/mm/slob.c b/mm/slob.c index 08a9bd91a1aa..ee2ef8af0d43 100644 --- a/mm/slob.c +++ b/mm/slob.c @@ -495,6 +495,7 @@ size_t ksize(const void *block) else return sp->page.private; } +EXPORT_SYMBOL(ksize); struct kmem_cache { unsigned int size, align; diff --git a/mm/slub.c b/mm/slub.c index 9acb413858ac..b9f37cb0f2e6 100644 --- a/mm/slub.c +++ b/mm/slub.c @@ -2558,8 +2558,12 @@ size_t ksize(const void *object) if (unlikely(object == ZERO_SIZE_PTR)) return 0; - page = get_object_page(object); + page = virt_to_head_page(object); BUG_ON(!page); + + if (unlikely(!PageSlab(page))) + return PAGE_SIZE << compound_order(page); + s = page->slab; BUG_ON(!s); diff --git a/net/8021q/vlan.c b/net/8021q/vlan.c index 6567213959cb..5b183156307a 100644 --- a/net/8021q/vlan.c +++ b/net/8021q/vlan.c @@ -776,7 +776,7 @@ static int vlan_ioctl_handler(struct net *net, void __user *arg) case SET_VLAN_NAME_TYPE_CMD: err = -EPERM; if (!capable(CAP_NET_ADMIN)) - return -EPERM; + break; if ((args.u.name_type >= 0) && (args.u.name_type < VLAN_NAME_TYPE_HIGHEST)) { vlan_name_type = args.u.name_type; diff --git a/net/8021q/vlan_dev.c b/net/8021q/vlan_dev.c index 7a36878241da..4f99bb86af5c 100644 --- a/net/8021q/vlan_dev.c +++ b/net/8021q/vlan_dev.c @@ -462,7 +462,8 @@ int vlan_dev_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) * OTHER THINGS LIKE FDDI/TokenRing/802.3 SNAPs... */ - if (veth->h_vlan_proto != htons(ETH_P_8021Q)) { + if (veth->h_vlan_proto != htons(ETH_P_8021Q) || + VLAN_DEV_INFO(dev)->flags & VLAN_FLAG_REORDER_HDR) { int orig_headroom = skb_headroom(skb); unsigned short veth_TCI; diff --git a/net/bridge/br.c b/net/bridge/br.c index 93867bb6cc97..a90182873120 100644 --- a/net/bridge/br.c +++ b/net/bridge/br.c @@ -39,7 +39,7 @@ static int __init br_init(void) err = br_fdb_init(); if (err) - goto err_out1; + goto err_out; err = br_netfilter_init(); if (err) @@ -65,6 +65,8 @@ err_out3: err_out2: br_netfilter_fini(); err_out1: + br_fdb_fini(); +err_out: llc_sap_put(br_stp_sap); return err; } diff --git a/net/bridge/br_fdb.c b/net/bridge/br_fdb.c index eb57502bb264..bc40377136a2 100644 --- a/net/bridge/br_fdb.c +++ b/net/bridge/br_fdb.c @@ -44,7 +44,7 @@ int __init br_fdb_init(void) return 0; } -void __exit br_fdb_fini(void) +void br_fdb_fini(void) { kmem_cache_destroy(br_fdb_cache); } diff --git a/net/bridge/br_input.c b/net/bridge/br_input.c index 3cedd4eeeed6..0ee79a726d91 100644 --- a/net/bridge/br_input.c +++ b/net/bridge/br_input.c @@ -122,6 +122,7 @@ static inline int is_link_local(const unsigned char *dest) struct sk_buff *br_handle_frame(struct net_bridge_port *p, struct sk_buff *skb) { const unsigned char *dest = eth_hdr(skb)->h_dest; + int (*rhook)(struct sk_buff *skb); if (!is_valid_ether_addr(eth_hdr(skb)->h_source)) goto drop; @@ -147,9 +148,9 @@ struct sk_buff *br_handle_frame(struct net_bridge_port *p, struct sk_buff *skb) switch (p->state) { case BR_STATE_FORWARDING: - - if (br_should_route_hook) { - if (br_should_route_hook(skb)) + rhook = rcu_dereference(br_should_route_hook); + if (rhook != NULL) { + if (rhook(skb)) return skb; dest = eth_hdr(skb)->h_dest; } diff --git a/net/bridge/netfilter/ebtable_broute.c b/net/bridge/netfilter/ebtable_broute.c index e44519ebf1d2..be6f18681053 100644 --- a/net/bridge/netfilter/ebtable_broute.c +++ b/net/bridge/netfilter/ebtable_broute.c @@ -70,13 +70,13 @@ static int __init ebtable_broute_init(void) if (ret < 0) return ret; /* see br_input.c */ - br_should_route_hook = ebt_broute; + rcu_assign_pointer(br_should_route_hook, ebt_broute); return ret; } static void __exit ebtable_broute_fini(void) { - br_should_route_hook = NULL; + rcu_assign_pointer(br_should_route_hook, NULL); synchronize_net(); ebt_unregister_table(&broute_table); } diff --git a/net/decnet/dn_dev.c b/net/decnet/dn_dev.c index 66e266fb5908..3bc82dc83b38 100644 --- a/net/decnet/dn_dev.c +++ b/net/decnet/dn_dev.c @@ -651,16 +651,18 @@ static int dn_nl_deladdr(struct sk_buff *skb, struct nlmsghdr *nlh, void *arg) struct dn_dev *dn_db; struct ifaddrmsg *ifm; struct dn_ifaddr *ifa, **ifap; - int err = -EADDRNOTAVAIL; + int err; err = nlmsg_parse(nlh, sizeof(*ifm), tb, IFA_MAX, dn_ifa_policy); if (err < 0) goto errout; + err = -ENODEV; ifm = nlmsg_data(nlh); if ((dn_db = dn_dev_by_index(ifm->ifa_index)) == NULL) goto errout; + err = -EADDRNOTAVAIL; for (ifap = &dn_db->ifa_list; (ifa = *ifap); ifap = &ifa->ifa_next) { if (tb[IFA_LOCAL] && nla_memcmp(tb[IFA_LOCAL], &ifa->ifa_local, 2)) diff --git a/net/ieee80211/ieee80211_tx.c b/net/ieee80211/ieee80211_tx.c index a4c3c51140a3..6d06f1385e28 100644 --- a/net/ieee80211/ieee80211_tx.c +++ b/net/ieee80211/ieee80211_tx.c @@ -144,7 +144,8 @@ static int ieee80211_copy_snap(u8 * data, u16 h_proto) snap->oui[1] = oui[1]; snap->oui[2] = oui[2]; - *(u16 *) (data + SNAP_SIZE) = htons(h_proto); + h_proto = htons(h_proto); + memcpy(data + SNAP_SIZE, &h_proto, sizeof(u16)); return SNAP_SIZE + sizeof(u16); } diff --git a/net/ipv4/inet_diag.c b/net/ipv4/inet_diag.c index b0170732b5e9..e468e7a7aac4 100644 --- a/net/ipv4/inet_diag.c +++ b/net/ipv4/inet_diag.c @@ -51,6 +51,29 @@ static struct sock *idiagnl; #define INET_DIAG_PUT(skb, attrtype, attrlen) \ RTA_DATA(__RTA_PUT(skb, attrtype, attrlen)) +static DEFINE_MUTEX(inet_diag_table_mutex); + +static const struct inet_diag_handler *inet_diag_lock_handler(int type) +{ +#ifdef CONFIG_KMOD + if (!inet_diag_table[type]) + request_module("net-pf-%d-proto-%d-type-%d", PF_NETLINK, + NETLINK_INET_DIAG, type); +#endif + + mutex_lock(&inet_diag_table_mutex); + if (!inet_diag_table[type]) + return ERR_PTR(-ENOENT); + + return inet_diag_table[type]; +} + +static inline void inet_diag_unlock_handler( + const struct inet_diag_handler *handler) +{ + mutex_unlock(&inet_diag_table_mutex); +} + static int inet_csk_diag_fill(struct sock *sk, struct sk_buff *skb, int ext, u32 pid, u32 seq, u16 nlmsg_flags, @@ -235,9 +258,12 @@ static int inet_diag_get_exact(struct sk_buff *in_skb, struct inet_hashinfo *hashinfo; const struct inet_diag_handler *handler; - handler = inet_diag_table[nlh->nlmsg_type]; - BUG_ON(handler == NULL); + handler = inet_diag_lock_handler(nlh->nlmsg_type); + if (!handler) + return -ENOENT; + hashinfo = handler->idiag_hashinfo; + err = -EINVAL; if (req->idiag_family == AF_INET) { sk = inet_lookup(hashinfo, req->id.idiag_dst[0], @@ -255,11 +281,12 @@ static int inet_diag_get_exact(struct sk_buff *in_skb, } #endif else { - return -EINVAL; + goto unlock; } + err = -ENOENT; if (sk == NULL) - return -ENOENT; + goto unlock; err = -ESTALE; if ((req->id.idiag_cookie[0] != INET_DIAG_NOCOOKIE || @@ -296,6 +323,8 @@ out: else sock_put(sk); } +unlock: + inet_diag_unlock_handler(handler); return err; } @@ -678,8 +707,10 @@ static int inet_diag_dump(struct sk_buff *skb, struct netlink_callback *cb) const struct inet_diag_handler *handler; struct inet_hashinfo *hashinfo; - handler = inet_diag_table[cb->nlh->nlmsg_type]; - BUG_ON(handler == NULL); + handler = inet_diag_lock_handler(cb->nlh->nlmsg_type); + if (!handler) + goto no_handler; + hashinfo = handler->idiag_hashinfo; s_i = cb->args[1]; @@ -743,7 +774,7 @@ skip_listen_ht: } if (!(r->idiag_states & ~(TCPF_LISTEN | TCPF_SYN_RECV))) - return skb->len; + goto unlock; for (i = s_i; i < hashinfo->ehash_size; i++) { struct inet_ehash_bucket *head = &hashinfo->ehash[i]; @@ -805,6 +836,9 @@ next_dying: done: cb->args[1] = i; cb->args[2] = num; +unlock: + inet_diag_unlock_handler(handler); +no_handler: return skb->len; } @@ -816,15 +850,6 @@ static int inet_diag_rcv_msg(struct sk_buff *skb, struct nlmsghdr *nlh) nlmsg_len(nlh) < hdrlen) return -EINVAL; -#ifdef CONFIG_KMOD - if (inet_diag_table[nlh->nlmsg_type] == NULL) - request_module("net-pf-%d-proto-%d-type-%d", PF_NETLINK, - NETLINK_INET_DIAG, nlh->nlmsg_type); -#endif - - if (inet_diag_table[nlh->nlmsg_type] == NULL) - return -ENOENT; - if (nlh->nlmsg_flags & NLM_F_DUMP) { if (nlmsg_attrlen(nlh, hdrlen)) { struct nlattr *attr; @@ -853,8 +878,6 @@ static void inet_diag_rcv(struct sk_buff *skb) mutex_unlock(&inet_diag_mutex); } -static DEFINE_SPINLOCK(inet_diag_register_lock); - int inet_diag_register(const struct inet_diag_handler *h) { const __u16 type = h->idiag_type; @@ -863,13 +886,13 @@ int inet_diag_register(const struct inet_diag_handler *h) if (type >= INET_DIAG_GETSOCK_MAX) goto out; - spin_lock(&inet_diag_register_lock); + mutex_lock(&inet_diag_table_mutex); err = -EEXIST; if (inet_diag_table[type] == NULL) { inet_diag_table[type] = h; err = 0; } - spin_unlock(&inet_diag_register_lock); + mutex_unlock(&inet_diag_table_mutex); out: return err; } @@ -882,11 +905,9 @@ void inet_diag_unregister(const struct inet_diag_handler *h) if (type >= INET_DIAG_GETSOCK_MAX) return; - spin_lock(&inet_diag_register_lock); + mutex_lock(&inet_diag_table_mutex); inet_diag_table[type] = NULL; - spin_unlock(&inet_diag_register_lock); - - synchronize_rcu(); + mutex_unlock(&inet_diag_table_mutex); } EXPORT_SYMBOL_GPL(inet_diag_unregister); diff --git a/net/ipv4/inet_lro.c b/net/ipv4/inet_lro.c index ac3b1d3dba2e..9a96c277393d 100644 --- a/net/ipv4/inet_lro.c +++ b/net/ipv4/inet_lro.c @@ -401,10 +401,11 @@ static struct sk_buff *lro_gen_skb(struct net_lro_mgr *lro_mgr, int data_len = len; int hdr_len = min(len, hlen); - skb = netdev_alloc_skb(lro_mgr->dev, hlen); + skb = netdev_alloc_skb(lro_mgr->dev, hlen + lro_mgr->frag_align_pad); if (!skb) return NULL; + skb_reserve(skb, lro_mgr->frag_align_pad); skb->len = len; skb->data_len = len - hdr_len; skb->truesize += true_size; diff --git a/net/ipv4/ipvs/ip_vs_lblc.c b/net/ipv4/ipvs/ip_vs_lblc.c index b843a11d7cf7..ad89644ef5d2 100644 --- a/net/ipv4/ipvs/ip_vs_lblc.c +++ b/net/ipv4/ipvs/ip_vs_lblc.c @@ -580,9 +580,14 @@ static struct ip_vs_scheduler ip_vs_lblc_scheduler = static int __init ip_vs_lblc_init(void) { + int ret; + INIT_LIST_HEAD(&ip_vs_lblc_scheduler.n_list); sysctl_header = register_sysctl_table(lblc_root_table); - return register_ip_vs_scheduler(&ip_vs_lblc_scheduler); + ret = register_ip_vs_scheduler(&ip_vs_lblc_scheduler); + if (ret) + unregister_sysctl_table(sysctl_header); + return ret; } diff --git a/net/ipv4/ipvs/ip_vs_lblcr.c b/net/ipv4/ipvs/ip_vs_lblcr.c index e5b323a6b2f7..2a5ed85a3352 100644 --- a/net/ipv4/ipvs/ip_vs_lblcr.c +++ b/net/ipv4/ipvs/ip_vs_lblcr.c @@ -769,9 +769,14 @@ static struct ip_vs_scheduler ip_vs_lblcr_scheduler = static int __init ip_vs_lblcr_init(void) { + int ret; + INIT_LIST_HEAD(&ip_vs_lblcr_scheduler.n_list); sysctl_header = register_sysctl_table(lblcr_root_table); - return register_ip_vs_scheduler(&ip_vs_lblcr_scheduler); + ret = register_ip_vs_scheduler(&ip_vs_lblcr_scheduler); + if (ret) + unregister_sysctl_table(sysctl_header); + return ret; } diff --git a/net/ipv4/ipvs/ip_vs_sched.c b/net/ipv4/ipvs/ip_vs_sched.c index 1602304abbf9..432235861908 100644 --- a/net/ipv4/ipvs/ip_vs_sched.c +++ b/net/ipv4/ipvs/ip_vs_sched.c @@ -183,19 +183,6 @@ int register_ip_vs_scheduler(struct ip_vs_scheduler *scheduler) /* increase the module use count */ ip_vs_use_count_inc(); - /* - * Make sure that the scheduler with this name doesn't exist - * in the scheduler list. - */ - sched = ip_vs_sched_getbyname(scheduler->name); - if (sched) { - ip_vs_scheduler_put(sched); - ip_vs_use_count_dec(); - IP_VS_ERR("register_ip_vs_scheduler(): [%s] scheduler " - "already existed in the system\n", scheduler->name); - return -EINVAL; - } - write_lock_bh(&__ip_vs_sched_lock); if (scheduler->n_list.next != &scheduler->n_list) { @@ -207,6 +194,20 @@ int register_ip_vs_scheduler(struct ip_vs_scheduler *scheduler) } /* + * Make sure that the scheduler with this name doesn't exist + * in the scheduler list. + */ + list_for_each_entry(sched, &ip_vs_schedulers, n_list) { + if (strcmp(scheduler->name, sched->name) == 0) { + write_unlock_bh(&__ip_vs_sched_lock); + ip_vs_use_count_dec(); + IP_VS_ERR("register_ip_vs_scheduler(): [%s] scheduler " + "already existed in the system\n", + scheduler->name); + return -EINVAL; + } + } + /* * Add it into the d-linked scheduler list */ list_add(&scheduler->n_list, &ip_vs_schedulers); diff --git a/net/ipv4/route.c b/net/ipv4/route.c index c426dec6d579..d2bc6148a737 100644 --- a/net/ipv4/route.c +++ b/net/ipv4/route.c @@ -1161,7 +1161,7 @@ static struct dst_entry *ipv4_negative_advice(struct dst_entry *dst) unsigned hash = rt_hash(rt->fl.fl4_dst, rt->fl.fl4_src, rt->fl.oif); #if RT_CACHE_DEBUG >= 1 - printk(KERN_DEBUG "ip_rt_advice: redirect to " + printk(KERN_DEBUG "ipv4_negative_advice: redirect to " "%u.%u.%u.%u/%02x dropped\n", NIPQUAD(rt->rt_dst), rt->fl.fl4_tos); #endif @@ -1252,6 +1252,7 @@ static int ip_error(struct sk_buff *skb) break; case ENETUNREACH: code = ICMP_NET_UNREACH; + IP_INC_STATS_BH(IPSTATS_MIB_INNOROUTES); break; case EACCES: code = ICMP_PKT_FILTERED; @@ -1881,6 +1882,8 @@ no_route: RT_CACHE_STAT_INC(in_no_route); spec_dst = inet_select_addr(dev, 0, RT_SCOPE_UNIVERSE); res.type = RTN_UNREACHABLE; + if (err == -ESRCH) + err = -ENETUNREACH; goto local_input; /* diff --git a/net/ipv4/tcp_illinois.c b/net/ipv4/tcp_illinois.c index 64f1cbaf96e8..5aa5f5496d6d 100644 --- a/net/ipv4/tcp_illinois.c +++ b/net/ipv4/tcp_illinois.c @@ -298,7 +298,7 @@ static u32 tcp_illinois_ssthresh(struct sock *sk) struct illinois *ca = inet_csk_ca(sk); /* Multiplicative decrease */ - return max((tp->snd_cwnd * ca->beta) >> BETA_SHIFT, 2U); + return max(tp->snd_cwnd - ((tp->snd_cwnd * ca->beta) >> BETA_SHIFT), 2U); } diff --git a/net/ipv4/tcp_input.c b/net/ipv4/tcp_input.c index 0f0c1c9829a1..b9e429d2d1de 100644 --- a/net/ipv4/tcp_input.c +++ b/net/ipv4/tcp_input.c @@ -3003,17 +3003,13 @@ static int tcp_process_frto(struct sock *sk, int flag) } if (tp->frto_counter == 1) { - /* Sending of the next skb must be allowed or no F-RTO */ - if (!tcp_send_head(sk) || - after(TCP_SKB_CB(tcp_send_head(sk))->end_seq, - tp->snd_una + tp->snd_wnd)) { - tcp_enter_frto_loss(sk, (tp->frto_counter == 1 ? 2 : 3), - flag); - return 1; - } - + /* tcp_may_send_now needs to see updated state */ tp->snd_cwnd = tcp_packets_in_flight(tp) + 2; tp->frto_counter = 2; + + if (!tcp_may_send_now(sk)) + tcp_enter_frto_loss(sk, 2, flag); + return 1; } else { switch (sysctl_tcp_frto_response) { @@ -3069,6 +3065,7 @@ static int tcp_ack(struct sock *sk, struct sk_buff *skb, int flag) } prior_fackets = tp->fackets_out; + prior_in_flight = tcp_packets_in_flight(tp); if (!(flag&FLAG_SLOWPATH) && after(ack, prior_snd_una)) { /* Window is constant, pure forward advance. @@ -3108,8 +3105,6 @@ static int tcp_ack(struct sock *sk, struct sk_buff *skb, int flag) if (!prior_packets) goto no_queue; - prior_in_flight = tcp_packets_in_flight(tp); - /* See if we can take anything off of the retransmit queue. */ flag |= tcp_clean_rtx_queue(sk, &seq_rtt, prior_fackets); diff --git a/net/ipv4/tcp_output.c b/net/ipv4/tcp_output.c index e5130a7fe181..f4c1eef89af0 100644 --- a/net/ipv4/tcp_output.c +++ b/net/ipv4/tcp_output.c @@ -1162,8 +1162,7 @@ int tcp_may_send_now(struct sock *sk) return (skb && tcp_snd_test(sk, skb, tcp_current_mss(sk, 1), (tcp_skb_is_last(sk, skb) ? - TCP_NAGLE_PUSH : - tp->nonagle))); + tp->nonagle : TCP_NAGLE_PUSH))); } /* Trim TSO SKB to LEN bytes, put the remaining data into a new packet diff --git a/net/ipv6/addrconf.c b/net/ipv6/addrconf.c index 567664eac463..e8c347579da9 100644 --- a/net/ipv6/addrconf.c +++ b/net/ipv6/addrconf.c @@ -2293,6 +2293,9 @@ static int addrconf_notify(struct notifier_block *this, unsigned long event, break; } + if (!idev && dev->mtu >= IPV6_MIN_MTU) + idev = ipv6_add_dev(dev); + if (idev) idev->if_flags |= IF_READY; } else { @@ -2357,12 +2360,18 @@ static int addrconf_notify(struct notifier_block *this, unsigned long event, break; case NETDEV_CHANGEMTU: - if ( idev && dev->mtu >= IPV6_MIN_MTU) { + if (idev && dev->mtu >= IPV6_MIN_MTU) { rt6_mtu_change(dev, dev->mtu); idev->cnf.mtu6 = dev->mtu; break; } + if (!idev && dev->mtu >= IPV6_MIN_MTU) { + idev = ipv6_add_dev(dev); + if (idev) + break; + } + /* MTU falled under IPV6_MIN_MTU. Stop IPv6 on this interface. */ case NETDEV_DOWN: diff --git a/net/ipv6/ip6_output.c b/net/ipv6/ip6_output.c index 86e1835ce4e4..6338a9c1aa14 100644 --- a/net/ipv6/ip6_output.c +++ b/net/ipv6/ip6_output.c @@ -933,6 +933,8 @@ static int ip6_dst_lookup_tail(struct sock *sk, return 0; out_err_release: + if (err == -ENETUNREACH) + IP6_INC_STATS_BH(NULL, IPSTATS_MIB_OUTNOROUTES); dst_release(*dst); *dst = NULL; return err; diff --git a/net/irda/ircomm/ircomm_tty.c b/net/irda/ircomm/ircomm_tty.c index 1120b150e211..be627e1f04d8 100644 --- a/net/irda/ircomm/ircomm_tty.c +++ b/net/irda/ircomm/ircomm_tty.c @@ -1245,6 +1245,7 @@ static void ircomm_tty_flow_indication(void *instance, void *sap, self->flow = cmd; } +#ifdef CONFIG_PROC_FS static int ircomm_tty_line_info(struct ircomm_tty_cb *self, char *buf) { int ret=0; @@ -1354,7 +1355,6 @@ static int ircomm_tty_line_info(struct ircomm_tty_cb *self, char *buf) * * */ -#ifdef CONFIG_PROC_FS static int ircomm_tty_read_proc(char *buf, char **start, off_t offset, int len, int *eof, void *unused) { diff --git a/net/mac80211/ieee80211.c b/net/mac80211/ieee80211.c index 59350b8727ec..505af1f067ab 100644 --- a/net/mac80211/ieee80211.c +++ b/net/mac80211/ieee80211.c @@ -216,6 +216,7 @@ static int ieee80211_open(struct net_device *dev) res = local->ops->start(local_to_hw(local)); if (res) return res; + ieee80211_hw_config(local); } switch (sdata->type) { @@ -232,7 +233,6 @@ static int ieee80211_open(struct net_device *dev) netif_tx_unlock_bh(local->mdev); local->hw.conf.flags |= IEEE80211_CONF_RADIOTAP; - ieee80211_hw_config(local); } break; case IEEE80211_IF_TYPE_STA: @@ -334,8 +334,7 @@ static int ieee80211_stop(struct net_device *dev) ieee80211_configure_filter(local); netif_tx_unlock_bh(local->mdev); - local->hw.conf.flags |= IEEE80211_CONF_RADIOTAP; - ieee80211_hw_config(local); + local->hw.conf.flags &= ~IEEE80211_CONF_RADIOTAP; } break; case IEEE80211_IF_TYPE_STA: @@ -357,6 +356,11 @@ static int ieee80211_stop(struct net_device *dev) cancel_delayed_work(&local->scan_work); } flush_workqueue(local->hw.workqueue); + + sdata->u.sta.flags &= ~IEEE80211_STA_PRIVACY_INVOKED; + kfree(sdata->u.sta.extra_ie); + sdata->u.sta.extra_ie = NULL; + sdata->u.sta.extra_ie_len = 0; /* fall through */ default: conf.if_id = dev->ifindex; diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c index 428a9fcf57d6..00f908d9275e 100644 --- a/net/mac80211/rx.c +++ b/net/mac80211/rx.c @@ -997,7 +997,7 @@ ieee80211_rx_h_drop_unencrypted(struct ieee80211_txrx_data *rx) if (unlikely(!(rx->fc & IEEE80211_FCTL_PROTECTED) && (rx->fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_DATA && (rx->fc & IEEE80211_FCTL_STYPE) != IEEE80211_STYPE_NULLFUNC && - rx->sdata->drop_unencrypted && + (rx->key || rx->sdata->drop_unencrypted) && (rx->sdata->eapol == 0 || !ieee80211_is_eapol(rx->skb)))) { if (net_ratelimit()) printk(KERN_DEBUG "%s: RX non-WEP frame, but expected " diff --git a/net/mac80211/wep.c b/net/mac80211/wep.c index 9bf0e1cc530a..b5f3413403bd 100644 --- a/net/mac80211/wep.c +++ b/net/mac80211/wep.c @@ -265,7 +265,8 @@ int ieee80211_wep_decrypt(struct ieee80211_local *local, struct sk_buff *skb, if (ieee80211_wep_decrypt_data(local->wep_rx_tfm, rc4key, klen, skb->data + hdrlen + WEP_IV_LEN, len)) { - printk(KERN_DEBUG "WEP decrypt failed (ICV)\n"); + if (net_ratelimit()) + printk(KERN_DEBUG "WEP decrypt failed (ICV)\n"); ret = -1; } diff --git a/net/netfilter/xt_CONNMARK.c b/net/netfilter/xt_CONNMARK.c index 856793e8db7a..0621ca7de3b0 100644 --- a/net/netfilter/xt_CONNMARK.c +++ b/net/netfilter/xt_CONNMARK.c @@ -86,11 +86,6 @@ checkentry(const char *tablename, { const struct xt_connmark_target_info *matchinfo = targinfo; - if (nf_ct_l3proto_try_module_get(target->family) < 0) { - printk(KERN_WARNING "can't load conntrack support for " - "proto=%d\n", target->family); - return false; - } if (matchinfo->mode == XT_CONNMARK_RESTORE) { if (strcmp(tablename, "mangle") != 0) { printk(KERN_WARNING "CONNMARK: restore can only be " @@ -103,6 +98,11 @@ checkentry(const char *tablename, printk(KERN_WARNING "CONNMARK: Only supports 32bit mark\n"); return false; } + if (nf_ct_l3proto_try_module_get(target->family) < 0) { + printk(KERN_WARNING "can't load conntrack support for " + "proto=%d\n", target->family); + return false; + } return true; } diff --git a/net/netfilter/xt_CONNSECMARK.c b/net/netfilter/xt_CONNSECMARK.c index 021b5c8d20e2..d8feba9bdb48 100644 --- a/net/netfilter/xt_CONNSECMARK.c +++ b/net/netfilter/xt_CONNSECMARK.c @@ -90,11 +90,6 @@ static bool checkentry(const char *tablename, const void *entry, { const struct xt_connsecmark_target_info *info = targinfo; - if (nf_ct_l3proto_try_module_get(target->family) < 0) { - printk(KERN_WARNING "can't load conntrack support for " - "proto=%d\n", target->family); - return false; - } switch (info->mode) { case CONNSECMARK_SAVE: case CONNSECMARK_RESTORE: @@ -105,6 +100,11 @@ static bool checkentry(const char *tablename, const void *entry, return false; } + if (nf_ct_l3proto_try_module_get(target->family) < 0) { + printk(KERN_WARNING "can't load conntrack support for " + "proto=%d\n", target->family); + return false; + } return true; } diff --git a/net/netfilter/xt_TCPMSS.c b/net/netfilter/xt_TCPMSS.c index 07435a602b11..8e76d1f52fbe 100644 --- a/net/netfilter/xt_TCPMSS.c +++ b/net/netfilter/xt_TCPMSS.c @@ -174,10 +174,8 @@ xt_tcpmss_target6(struct sk_buff *skb, nexthdr = ipv6h->nexthdr; tcphoff = ipv6_skip_exthdr(skb, sizeof(*ipv6h), &nexthdr); - if (tcphoff < 0) { - WARN_ON(1); + if (tcphoff < 0) return NF_DROP; - } ret = tcpmss_mangle_packet(skb, targinfo, tcphoff, sizeof(*ipv6h) + sizeof(struct tcphdr)); if (ret < 0) diff --git a/net/rfkill/rfkill.c b/net/rfkill/rfkill.c index 73d60a307129..4469a7be006c 100644 --- a/net/rfkill/rfkill.c +++ b/net/rfkill/rfkill.c @@ -60,11 +60,7 @@ static void rfkill_led_trigger(struct rfkill *rfkill, static int rfkill_toggle_radio(struct rfkill *rfkill, enum rfkill_state state) { - int retval; - - retval = mutex_lock_interruptible(&rfkill->mutex); - if (retval) - return retval; + int retval = 0; if (state != rfkill->state) { retval = rfkill->toggle_radio(rfkill->data, state); @@ -74,7 +70,6 @@ static int rfkill_toggle_radio(struct rfkill *rfkill, } } - mutex_unlock(&rfkill->mutex); return retval; } @@ -158,12 +153,13 @@ static ssize_t rfkill_state_store(struct device *dev, if (!capable(CAP_NET_ADMIN)) return -EPERM; + if (mutex_lock_interruptible(&rfkill->mutex)) + return -ERESTARTSYS; error = rfkill_toggle_radio(rfkill, state ? RFKILL_STATE_ON : RFKILL_STATE_OFF); - if (error) - return error; + mutex_unlock(&rfkill->mutex); - return count; + return error ? error : count; } static ssize_t rfkill_claim_show(struct device *dev, diff --git a/net/rose/rose_dev.c b/net/rose/rose_dev.c index 1b6741f1d746..12cfcf09556b 100644 --- a/net/rose/rose_dev.c +++ b/net/rose/rose_dev.c @@ -55,13 +55,13 @@ static int rose_header(struct sk_buff *skb, struct net_device *dev, static int rose_rebuild_header(struct sk_buff *skb) { +#ifdef CONFIG_INET struct net_device *dev = skb->dev; struct net_device_stats *stats = netdev_priv(dev); unsigned char *bp = (unsigned char *)skb->data; struct sk_buff *skbn; unsigned int len; -#ifdef CONFIG_INET if (arp_find(bp + 7, skb)) { return 1; } diff --git a/net/rxrpc/Kconfig b/net/rxrpc/Kconfig index e662f1d07664..0d3103c4f11c 100644 --- a/net/rxrpc/Kconfig +++ b/net/rxrpc/Kconfig @@ -5,6 +5,7 @@ config AF_RXRPC tristate "RxRPC session sockets" depends on INET && EXPERIMENTAL + select CRYPTO select KEYS help Say Y or M here to include support for RxRPC session sockets (just diff --git a/net/rxrpc/rxkad.c b/net/rxrpc/rxkad.c index e09a95aa68ff..8e69d6993833 100644 --- a/net/rxrpc/rxkad.c +++ b/net/rxrpc/rxkad.c @@ -1021,6 +1021,7 @@ static int rxkad_verify_response(struct rxrpc_connection *conn, abort_code = RXKADINCONSISTENCY; if (version != RXKAD_VERSION) + goto protocol_error; abort_code = RXKADTICKETLEN; if (ticket_len < 4 || ticket_len > MAXKRB5TICKETLEN) diff --git a/net/sctp/Kconfig b/net/sctp/Kconfig index 8210f549c492..5390bc792159 100644 --- a/net/sctp/Kconfig +++ b/net/sctp/Kconfig @@ -6,9 +6,9 @@ menuconfig IP_SCTP tristate "The SCTP Protocol (EXPERIMENTAL)" depends on INET && EXPERIMENTAL depends on IPV6 || IPV6=n - select CRYPTO if SCTP_HMAC_SHA1 || SCTP_HMAC_MD5 - select CRYPTO_HMAC if SCTP_HMAC_SHA1 || SCTP_HMAC_MD5 - select CRYPTO_SHA1 if SCTP_HMAC_SHA1 + select CRYPTO + select CRYPTO_HMAC + select CRYPTO_SHA1 select CRYPTO_MD5 if SCTP_HMAC_MD5 ---help--- Stream Control Transmission Protocol diff --git a/net/sctp/auth.c b/net/sctp/auth.c index 6d5fa6bb371b..97e6ebd14500 100644 --- a/net/sctp/auth.c +++ b/net/sctp/auth.c @@ -54,11 +54,13 @@ static struct sctp_hmac sctp_hmac_list[SCTP_AUTH_NUM_HMACS] = { /* id 2 is reserved as well */ .hmac_id = SCTP_AUTH_HMAC_ID_RESERVED_2, }, +#if defined (CONFIG_CRYPTO_SHA256) || defined (CONFIG_CRYPTO_SHA256_MODULE) { .hmac_id = SCTP_AUTH_HMAC_ID_SHA256, .hmac_name="hmac(sha256)", .hmac_len = SCTP_SHA256_SIG_SIZE, } +#endif }; @@ -631,7 +633,7 @@ static int __sctp_auth_cid(sctp_cid_t chunk, struct sctp_chunks_param *param) int found = 0; int i; - if (!param) + if (!param || param->param_hdr.length == 0) return 0; len = ntohs(param->param_hdr.length) - sizeof(sctp_paramhdr_t); diff --git a/net/sctp/bind_addr.c b/net/sctp/bind_addr.c index cae95af9a8cc..6a7d01091f0c 100644 --- a/net/sctp/bind_addr.c +++ b/net/sctp/bind_addr.c @@ -105,6 +105,32 @@ out: return error; } +/* Exactly duplicate the address lists. This is necessary when doing + * peer-offs and accepts. We don't want to put all the current system + * addresses into the endpoint. That's useless. But we do want duplicat + * the list of bound addresses that the older endpoint used. + */ +int sctp_bind_addr_dup(struct sctp_bind_addr *dest, + const struct sctp_bind_addr *src, + gfp_t gfp) +{ + struct sctp_sockaddr_entry *addr; + struct list_head *pos; + int error = 0; + + /* All addresses share the same port. */ + dest->port = src->port; + + list_for_each(pos, &src->address_list) { + addr = list_entry(pos, struct sctp_sockaddr_entry, list); + error = sctp_add_bind_addr(dest, &addr->a, 1, gfp); + if (error < 0) + break; + } + + return error; +} + /* Initialize the SCTP_bind_addr structure for either an endpoint or * an association. */ diff --git a/net/sctp/sm_make_chunk.c b/net/sctp/sm_make_chunk.c index 5a9783c38de1..f4876291bb5e 100644 --- a/net/sctp/sm_make_chunk.c +++ b/net/sctp/sm_make_chunk.c @@ -77,6 +77,8 @@ static int sctp_process_param(struct sctp_association *asoc, union sctp_params param, const union sctp_addr *peer_addr, gfp_t gfp); +static void *sctp_addto_param(struct sctp_chunk *chunk, int len, + const void *data); /* What was the inbound interface for this chunk? */ int sctp_chunk_iif(const struct sctp_chunk *chunk) @@ -207,11 +209,7 @@ struct sctp_chunk *sctp_make_init(const struct sctp_association *asoc, chunksize = sizeof(init) + addrs_len + SCTP_SAT_LEN(num_types); chunksize += sizeof(ecap_param); - if (sctp_prsctp_enable) { - chunksize += sizeof(prsctp_param); - extensions[num_ext] = SCTP_CID_FWD_TSN; - num_ext += 1; - } + /* ADDIP: Section 4.2.7: * An implementation supporting this extension [ADDIP] MUST list * the ASCONF,the ASCONF-ACK, and the AUTH chunks in its INIT and @@ -243,7 +241,7 @@ struct sctp_chunk *sctp_make_init(const struct sctp_association *asoc, if (auth_chunks->length) chunksize += ntohs(auth_chunks->length); else - auth_hmacs = NULL; + auth_chunks = NULL; extensions[num_ext] = SCTP_CID_AUTH; num_ext += 1; @@ -297,7 +295,7 @@ struct sctp_chunk *sctp_make_init(const struct sctp_association *asoc, htons(sizeof(sctp_supported_ext_param_t) + num_ext); sctp_addto_chunk(retval, sizeof(sctp_supported_ext_param_t), &ext_param); - sctp_addto_chunk(retval, num_ext, extensions); + sctp_addto_param(retval, num_ext, extensions); } if (sctp_prsctp_enable) @@ -371,20 +369,12 @@ struct sctp_chunk *sctp_make_init_ack(const struct sctp_association *asoc, if (asoc->peer.ecn_capable) chunksize += sizeof(ecap_param); - /* Tell peer that we'll do PR-SCTP only if peer advertised. */ - if (asoc->peer.prsctp_capable) { - chunksize += sizeof(prsctp_param); - extensions[num_ext] = SCTP_CID_FWD_TSN; - num_ext += 1; - } - if (sctp_addip_enable) { extensions[num_ext] = SCTP_CID_ASCONF; extensions[num_ext+1] = SCTP_CID_ASCONF_ACK; num_ext += 2; } - chunksize += sizeof(ext_param) + num_ext; chunksize += sizeof(aiparam); if (asoc->peer.auth_capable) { @@ -407,6 +397,9 @@ struct sctp_chunk *sctp_make_init_ack(const struct sctp_association *asoc, num_ext += 1; } + if (num_ext) + chunksize += sizeof(sctp_supported_ext_param_t) + num_ext; + /* Now allocate and fill out the chunk. */ retval = sctp_make_chunk(asoc, SCTP_CID_INIT_ACK, 0, chunksize); if (!retval) @@ -428,7 +421,7 @@ struct sctp_chunk *sctp_make_init_ack(const struct sctp_association *asoc, htons(sizeof(sctp_supported_ext_param_t) + num_ext); sctp_addto_chunk(retval, sizeof(sctp_supported_ext_param_t), &ext_param); - sctp_addto_chunk(retval, num_ext, extensions); + sctp_addto_param(retval, num_ext, extensions); } if (asoc->peer.prsctp_capable) sctp_addto_chunk(retval, sizeof(prsctp_param), &prsctp_param); diff --git a/net/sctp/sm_statefuns.c b/net/sctp/sm_statefuns.c index b8bbb960723c..5fb84778846d 100644 --- a/net/sctp/sm_statefuns.c +++ b/net/sctp/sm_statefuns.c @@ -959,7 +959,7 @@ sctp_disposition_t sctp_sf_sendbeat_8_3(const struct sctp_endpoint *ep, { struct sctp_transport *transport = (struct sctp_transport *) arg; - if (asoc->overall_error_count >= asoc->max_retrans) { + if (asoc->overall_error_count > asoc->max_retrans) { sctp_add_cmd_sf(commands, SCTP_CMD_SET_SK_ERR, SCTP_ERROR(ETIMEDOUT)); /* CMD_ASSOC_FAILED calls CMD_DELETE_TCB. */ diff --git a/net/sctp/socket.c b/net/sctp/socket.c index ff8bc95670ed..ea9649ca0b2a 100644 --- a/net/sctp/socket.c +++ b/net/sctp/socket.c @@ -6325,7 +6325,7 @@ static void sctp_sock_migrate(struct sock *oldsk, struct sock *newsk, struct sctp_endpoint *newep = newsp->ep; struct sk_buff *skb, *tmp; struct sctp_ulpevent *event; - int flags = 0; + struct sctp_bind_hashbucket *head; /* Migrate socket buffer sizes and all the socket level options to the * new socket. @@ -6342,23 +6342,21 @@ static void sctp_sock_migrate(struct sock *oldsk, struct sock *newsk, newsp->hmac = NULL; /* Hook this new socket in to the bind_hash list. */ + head = &sctp_port_hashtable[sctp_phashfn(inet_sk(oldsk)->num)]; + sctp_local_bh_disable(); + sctp_spin_lock(&head->lock); pp = sctp_sk(oldsk)->bind_hash; sk_add_bind_node(newsk, &pp->owner); sctp_sk(newsk)->bind_hash = pp; inet_sk(newsk)->num = inet_sk(oldsk)->num; + sctp_spin_unlock(&head->lock); + sctp_local_bh_enable(); /* Copy the bind_addr list from the original endpoint to the new * endpoint so that we can handle restarts properly */ - if (PF_INET6 == assoc->base.sk->sk_family) - flags = SCTP_ADDR6_ALLOWED; - if (assoc->peer.ipv4_address) - flags |= SCTP_ADDR4_PEERSUPP; - if (assoc->peer.ipv6_address) - flags |= SCTP_ADDR6_PEERSUPP; - sctp_bind_addr_copy(&newsp->ep->base.bind_addr, - &oldsp->ep->base.bind_addr, - SCTP_SCOPE_GLOBAL, GFP_KERNEL, flags); + sctp_bind_addr_dup(&newsp->ep->base.bind_addr, + &oldsp->ep->base.bind_addr, GFP_KERNEL); /* Move any messages in the old socket's receive queue that are for the * peeled off association to the new socket's receive queue. diff --git a/net/unix/af_unix.c b/net/unix/af_unix.c index e835da8fc091..060bba4567d2 100644 --- a/net/unix/af_unix.c +++ b/net/unix/af_unix.c @@ -1637,8 +1637,15 @@ static int unix_dgram_recvmsg(struct kiocb *iocb, struct socket *sock, mutex_lock(&u->readlock); skb = skb_recv_datagram(sk, flags, noblock, &err); - if (!skb) + if (!skb) { + unix_state_lock(sk); + /* Signal EOF on disconnected non-blocking SEQPACKET socket. */ + if (sk->sk_type == SOCK_SEQPACKET && err == -EAGAIN && + (sk->sk_shutdown & RCV_SHUTDOWN)) + err = 0; + unix_state_unlock(sk); goto out_unlock; + } wake_up_interruptible_sync(&u->peer_wait); diff --git a/net/xfrm/xfrm_policy.c b/net/xfrm/xfrm_policy.c index b702bd8a3893..9a4cf2e45a15 100644 --- a/net/xfrm/xfrm_policy.c +++ b/net/xfrm/xfrm_policy.c @@ -1344,6 +1344,7 @@ restart: xfrm_nr += pols[0]->xfrm_nr; switch (policy->action) { + default: case XFRM_POLICY_BLOCK: /* Prohibit the flow */ err = -EPERM; diff --git a/security/dummy.c b/security/dummy.c index 6d895ade73de..3ccfbbe973b6 100644 --- a/security/dummy.c +++ b/security/dummy.c @@ -426,7 +426,7 @@ static int dummy_file_mmap (struct file *file, unsigned long reqprot, unsigned long addr, unsigned long addr_only) { - if (addr < mmap_min_addr) + if ((addr < mmap_min_addr) && !capable(CAP_SYS_RAWIO)) return -EACCES; return 0; } diff --git a/security/selinux/selinuxfs.c b/security/selinux/selinuxfs.c index f5f3e6da5da7..2fa483f26113 100644 --- a/security/selinux/selinuxfs.c +++ b/security/selinux/selinuxfs.c @@ -65,6 +65,7 @@ static DEFINE_MUTEX(sel_mutex); /* global data for booleans */ static struct dentry *bool_dir = NULL; static int bool_num = 0; +static char **bool_pending_names; static int *bool_pending_values = NULL; /* global data for classes */ @@ -832,15 +833,16 @@ static ssize_t sel_read_bool(struct file *filep, char __user *buf, ssize_t length; ssize_t ret; int cur_enforcing; - struct inode *inode; + struct inode *inode = filep->f_path.dentry->d_inode; + unsigned index = inode->i_ino & SEL_INO_MASK; + const char *name = filep->f_path.dentry->d_name.name; mutex_lock(&sel_mutex); - ret = -EFAULT; - - /* check to see if this file has been deleted */ - if (!filep->f_op) + if (index >= bool_num || strcmp(name, bool_pending_names[index])) { + ret = -EINVAL; goto out; + } if (count > PAGE_SIZE) { ret = -EINVAL; @@ -851,15 +853,13 @@ static ssize_t sel_read_bool(struct file *filep, char __user *buf, goto out; } - inode = filep->f_path.dentry->d_inode; - cur_enforcing = security_get_bool_value(inode->i_ino&SEL_INO_MASK); + cur_enforcing = security_get_bool_value(index); if (cur_enforcing < 0) { ret = cur_enforcing; goto out; } - length = scnprintf(page, PAGE_SIZE, "%d %d", cur_enforcing, - bool_pending_values[inode->i_ino&SEL_INO_MASK]); + bool_pending_values[index]); ret = simple_read_from_buffer(buf, count, ppos, page, length); out: mutex_unlock(&sel_mutex); @@ -872,9 +872,11 @@ static ssize_t sel_write_bool(struct file *filep, const char __user *buf, size_t count, loff_t *ppos) { char *page = NULL; - ssize_t length = -EFAULT; + ssize_t length; int new_value; - struct inode *inode; + struct inode *inode = filep->f_path.dentry->d_inode; + unsigned index = inode->i_ino & SEL_INO_MASK; + const char *name = filep->f_path.dentry->d_name.name; mutex_lock(&sel_mutex); @@ -882,16 +884,19 @@ static ssize_t sel_write_bool(struct file *filep, const char __user *buf, if (length) goto out; - /* check to see if this file has been deleted */ - if (!filep->f_op) + if (index >= bool_num || strcmp(name, bool_pending_names[index])) { + length = -EINVAL; goto out; + } if (count >= PAGE_SIZE) { length = -ENOMEM; goto out; } + if (*ppos != 0) { /* No partial writes. */ + length = -EINVAL; goto out; } page = (char*)get_zeroed_page(GFP_KERNEL); @@ -900,6 +905,7 @@ static ssize_t sel_write_bool(struct file *filep, const char __user *buf, goto out; } + length = -EFAULT; if (copy_from_user(page, buf, count)) goto out; @@ -910,8 +916,7 @@ static ssize_t sel_write_bool(struct file *filep, const char __user *buf, if (new_value) new_value = 1; - inode = filep->f_path.dentry->d_inode; - bool_pending_values[inode->i_ino&SEL_INO_MASK] = new_value; + bool_pending_values[index] = new_value; length = count; out: @@ -931,7 +936,7 @@ static ssize_t sel_commit_bools_write(struct file *filep, size_t count, loff_t *ppos) { char *page = NULL; - ssize_t length = -EFAULT; + ssize_t length; int new_value; mutex_lock(&sel_mutex); @@ -940,10 +945,6 @@ static ssize_t sel_commit_bools_write(struct file *filep, if (length) goto out; - /* check to see if this file has been deleted */ - if (!filep->f_op) - goto out; - if (count >= PAGE_SIZE) { length = -ENOMEM; goto out; @@ -958,6 +959,7 @@ static ssize_t sel_commit_bools_write(struct file *filep, goto out; } + length = -EFAULT; if (copy_from_user(page, buf, count)) goto out; @@ -982,11 +984,9 @@ static const struct file_operations sel_commit_bools_ops = { .write = sel_commit_bools_write, }; -/* partial revoke() from fs/proc/generic.c proc_kill_inodes */ static void sel_remove_entries(struct dentry *de) { - struct list_head *p, *node; - struct super_block *sb = de->d_sb; + struct list_head *node; spin_lock(&dcache_lock); node = de->d_subdirs.next; @@ -1006,18 +1006,6 @@ static void sel_remove_entries(struct dentry *de) } spin_unlock(&dcache_lock); - - file_list_lock(); - list_for_each(p, &sb->s_files) { - struct file * filp = list_entry(p, struct file, f_u.fu_list); - struct dentry * dentry = filp->f_path.dentry; - - if (dentry->d_parent != de) { - continue; - } - filp->f_op = NULL; - } - file_list_unlock(); } #define BOOL_DIR_NAME "booleans" @@ -1036,7 +1024,9 @@ static int sel_make_bools(void) u32 sid; /* remove any existing files */ + kfree(bool_pending_names); kfree(bool_pending_values); + bool_pending_names = NULL; bool_pending_values = NULL; sel_remove_entries(dir); @@ -1078,16 +1068,17 @@ static int sel_make_bools(void) d_add(dentry, inode); } bool_num = num; + bool_pending_names = names; bool_pending_values = values; out: free_page((unsigned long)page); + return ret; +err: if (names) { for (i = 0; i < num; i++) kfree(names[i]); kfree(names); } - return ret; -err: kfree(values); sel_remove_entries(dir); ret = -ENOMEM; |