diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
49 files changed, 443 insertions, 144 deletions
diff --git a/Documentation/devicetree/bindings/arm/adapteva.txt b/Documentation/devicetree/bindings/arm/adapteva.txt deleted file mode 100644 index 1d8af9e36065..000000000000 --- a/Documentation/devicetree/bindings/arm/adapteva.txt +++ /dev/null @@ -1,7 +0,0 @@ -Adapteva Platforms Device Tree Bindings ---------------------------------------- - -Parallella board - -Required root node properties: - - compatible = "adapteva,parallella"; diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt index 69880560c0f0..b5c2b5c35766 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.txt +++ b/Documentation/devicetree/bindings/arm/amlogic.txt @@ -41,6 +41,14 @@ Boards with the Amlogic Meson GXL S905D SoC shall have the following properties: Required root node property: compatible: "amlogic,s905d", "amlogic,meson-gxl"; +Boards with the Amlogic Meson GXL S805X SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s805x", "amlogic,meson-gxl"; + +Boards with the Amlogic Meson GXL S905W SoC shall have the following properties: + Required root node property: + compatible: "amlogic,s905w", "amlogic,meson-gxl"; + Boards with the Amlogic Meson GXM S912 SoC shall have the following properties: Required root node property: compatible: "amlogic,s912", "amlogic,meson-gxm"; @@ -79,6 +87,11 @@ Board compatible values (alphabetically, grouped by SoC): - "amlogic,p230" (Meson gxl s905d) - "amlogic,p231" (Meson gxl s905d) + - "amlogic,p241" (Meson gxl s805x) + + - "amlogic,p281" (Meson gxl s905w) + - "oranth,tx3-mini" (Meson gxl s905w) + - "amlogic,q200" (Meson gxm s912) - "amlogic,q201" (Meson gxm s912) - "khadas,vim2" (Meson gxm s912) diff --git a/Documentation/devicetree/bindings/arm/atmel-pmc.txt b/Documentation/devicetree/bindings/arm/atmel-pmc.txt deleted file mode 100644 index 795cc78543fe..000000000000 --- a/Documentation/devicetree/bindings/arm/atmel-pmc.txt +++ /dev/null @@ -1,14 +0,0 @@ -* Power Management Controller (PMC) - -Required properties: -- compatible: Should be "atmel,<chip>-pmc". - <chip> can be: at91rm9200, at91sam9260, at91sam9g45, at91sam9n12, - at91sam9x5, sama5d3 - -- reg: Should contain PMC registers location and length - -Examples: - pmc: pmc@fffffc00 { - compatible = "atmel,at91rm9200-pmc"; - reg = <0xfffffc00 0x100>; - }; diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt index c052caad36e8..104cc9b41df4 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,brcmstb.txt @@ -189,7 +189,11 @@ Power-Down (SRPD), among other things. Required properties: - compatible : should contain one of these + "brcm,brcmstb-memc-ddr-rev-b.2.1" "brcm,brcmstb-memc-ddr-rev-b.2.2" + "brcm,brcmstb-memc-ddr-rev-b.2.3" + "brcm,brcmstb-memc-ddr-rev-b.3.0" + "brcm,brcmstb-memc-ddr-rev-b.3.1" "brcm,brcmstb-memc-ddr" - reg : the MEMC DDR register range diff --git a/Documentation/devicetree/bindings/arm/cpu-capacity.txt b/Documentation/devicetree/bindings/arm/cpu-capacity.txt index 7809fbe0cdb7..9b5685a1d15d 100644 --- a/Documentation/devicetree/bindings/arm/cpu-capacity.txt +++ b/Documentation/devicetree/bindings/arm/cpu-capacity.txt @@ -94,7 +94,7 @@ cpus { }; idle-states { - entry-method = "arm,psci"; + entry-method = "psci"; CPU_SLEEP_0: cpu-sleep-0 { compatible = "arm,idle-state"; diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 29e1dc5d506d..96dfccc0faa8 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -183,6 +183,7 @@ described below. "marvell,sheeva-v5" "nvidia,tegra132-denver" "nvidia,tegra186-denver" + "nvidia,tegra194-carmel" "qcom,krait" "qcom,kryo" "qcom,kryo385" @@ -219,6 +220,7 @@ described below. "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" "renesas,apmu" + "renesas,r9a06g032-smp" "rockchip,rk3036-smp" "rockchip,rk3066-smp" "ste,dbx500-smp" diff --git a/Documentation/devicetree/bindings/arm/freescale/m4if.txt b/Documentation/devicetree/bindings/arm/freescale/m4if.txt new file mode 100644 index 000000000000..93bd7b867a53 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/m4if.txt @@ -0,0 +1,12 @@ +* Freescale Multi Master Multi Memory Interface (M4IF) module + +Required properties: +- compatible : Should be "fsl,imx51-m4if" +- reg : Address and length of the register set for the device + +Example: + +m4if: m4if@83fd8000 { + compatible = "fsl,imx51-m4if"; + reg = <0x83fd8000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/arm/freescale/tigerp.txt b/Documentation/devicetree/bindings/arm/freescale/tigerp.txt new file mode 100644 index 000000000000..19e2aad63d6e --- /dev/null +++ b/Documentation/devicetree/bindings/arm/freescale/tigerp.txt @@ -0,0 +1,12 @@ +* Freescale Tigerp platform module + +Required properties: +- compatible : Should be "fsl,imx51-tigerp" +- reg : Address and length of the register set for the device + +Example: + +tigerp: tigerp@83fa0000 { + compatible = "fsl,imx51-tigerp"; + reg = <0x83fa0000 0x28>; +}; diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index cdb9dd705754..8a1baa2b9723 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board Required root node properties: - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; +i.MX6SLL EVK board +Required root node properties: + - compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; + Generic i.MX boards ------------------- diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt index 7a591333f2b1..2c73847499ab 100644 --- a/Documentation/devicetree/bindings/arm/idle-states.txt +++ b/Documentation/devicetree/bindings/arm/idle-states.txt @@ -237,8 +237,8 @@ processor idle states, defined as device tree nodes, are listed. Value type: <stringlist> Usage and definition depend on ARM architecture version. # On ARM v8 64-bit this property is required and must - be one of: - - "psci" (see bindings in [2]) + be: + - "psci" # On ARM 32-bit systems this property is optional The nodes describing the idle states (state) can only be defined within the diff --git a/Documentation/devicetree/bindings/arm/insignal-boards.txt b/Documentation/devicetree/bindings/arm/insignal-boards.txt deleted file mode 100644 index 524c3dc5d808..000000000000 --- a/Documentation/devicetree/bindings/arm/insignal-boards.txt +++ /dev/null @@ -1,8 +0,0 @@ -* Insignal's Exynos4210 based Origen evaluation board - -Origen low-cost evaluation board is based on Samsung's Exynos4210 SoC. - -Required root node properties: - - compatible = should be one or more of the following. - (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board. - (b) "samsung,exynos4210" - for boards based on Exynos4210 SoC. diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index 48fac4ec91fc..8f260e5cfd16 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -51,6 +51,9 @@ Supported boards: - Evaluation board for MT6797(Helio X20): Required root node properties: - compatible = "mediatek,mt6797-evb", "mediatek,mt6797"; +- Mediatek X20 Development Board: + Required root node properties: + - compatible = "archermind,mt6797-x20-dev", "mediatek,mt6797"; - Reference board variant 1 for MT7622: Required root node properties: - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622"; @@ -63,9 +66,6 @@ Supported boards: - Reference board for MT7623n with eMMC: Required root node properties: - compatible = "mediatek,mt7623n-rfb-emmc", "mediatek,mt7623"; -- Reference board for MT7623n with NAND: - Required root node properties: - - compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623"; - Bananapi BPI-R2 board: - compatible = "bananapi,bpi-r2", "mediatek,mt7623"; - MTK mt8127 tablet moose EVB: diff --git a/Documentation/devicetree/bindings/arm/omap/l4.txt b/Documentation/devicetree/bindings/arm/omap/l4.txt index b4f8a16e7e3b..6816adcdc15f 100644 --- a/Documentation/devicetree/bindings/arm/omap/l4.txt +++ b/Documentation/devicetree/bindings/arm/omap/l4.txt @@ -7,6 +7,7 @@ Required properties: Should be "ti,omap2-l4-wkup" for OMAP2 family l4 wkup bus Should be "ti,omap3-l4-core" for OMAP3 family l4 core bus Should be "ti,omap4-l4-cfg" for OMAP4 family l4 cfg bus + Should be "ti,omap4-l4-per" for OMAP4 family l4 per bus Should be "ti,omap4-l4-wkup" for OMAP4 family l4 wkup bus Should be "ti,omap5-l4-cfg" for OMAP5 family l4 cfg bus Should be "ti,omap5-l4-wkup" for OMAP5 family l4 wkup bus @@ -15,11 +16,21 @@ Required properties: Should be "ti,am3-l4-wkup" for AM33xx family l4 wkup bus Should be "ti,am4-l4-wkup" for AM43xx family l4 wkup bus - ranges : contains the IO map range for the bus +- reg : registers link agent and interconnect agent and access protection +- reg-names : "la" for link agent, "ia0" to "ia3" for one to three + interconnect agent instances, "ap" for access if it exists Examples: -l4: l4@48000000 { - compatible "ti,omap2-l4", "simple-bus"; +l4: interconnect@48000000 { + compatible "ti,omap4-l4-per", "simple-bus"; + reg = <0x48000000 0x800>, + <0x48000800 0x800>, + <0x48001000 0x400>, + <0x48001400 0x400>, + <0x48001800 0x400>, + <0x48001c00 0x400>; + reg-names = "ap", "la", "ia0", "ia1", "ia2", "ia3"; #address-cells = <1>; #size-cells = <1>; ranges = <0 0x48000000 0x100000>; diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 1c1d62d03c4f..acfd3c773dd0 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -1,5 +1,10 @@ Rockchip platforms device tree bindings --------------------------------------- + +- 96boards RK3399 Ficus (ROCK960 Enterprise Edition) + Required root node properties: + - compatible = "vamrs,ficus", "rockchip,rk3399"; + - Amarula Vyasa RK3288 board Required root node properties: - compatible = "amarula,vyasa-rk3288", "rockchip,rk3288"; @@ -66,6 +71,15 @@ Rockchip platforms device tree bindings Required root node properties: - compatible = "geekbuying,geekbox", "rockchip,rk3368"; +- Google Bob (Asus Chromebook Flip C101PA): + Required root node properties: + compatible = "google,bob-rev13", "google,bob-rev12", + "google,bob-rev11", "google,bob-rev10", + "google,bob-rev9", "google,bob-rev8", + "google,bob-rev7", "google,bob-rev6", + "google,bob-rev5", "google,bob-rev4", + "google,bob", "google,gru", "rockchip,rk3399"; + - Google Brain (dev-board): Required root node properties: - compatible = "google,veyron-brain-rev0", "google,veyron-brain", diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 6970f30a3770..56021bf2a916 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt @@ -1,7 +1,10 @@ -* Samsung's Exynos SoC based boards +* Samsung's Exynos and S5P SoC based boards Required root node properties: - compatible = should be one or more of the following. + - "samsung,aries" - for S5PV210-based Samsung Aries board. + - "samsung,fascinate4g" - for S5PV210-based Samsung Galaxy S Fascinate 4G (SGH-T959P) board. + - "samsung,galaxys" - for S5PV210-based Samsung Galaxy S (i9000) board. - "samsung,artik5" - for Exynos3250-based Samsung ARTIK5 module. - "samsung,artik5-eval" - for Exynos3250-based Samsung ARTIK5 eval board. - "samsung,monk" - for Exynos3250-based Samsung Simband board. diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt index d8cf740132c6..89b4a389fbc7 100644 --- a/Documentation/devicetree/bindings/arm/shmobile.txt +++ b/Documentation/devicetree/bindings/arm/shmobile.txt @@ -51,7 +51,8 @@ SoCs: compatible = "renesas,r8a77990" - R-Car D3 (R8A77995) compatible = "renesas,r8a77995" - + - RZ/N1D (R9A06G032) + compatible = "renesas,r9a06g032" Boards: @@ -112,6 +113,8 @@ Boards: compatible = "renesas,porter", "renesas,r8a7791" - RSKRZA1 (YR0K77210C000BE) compatible = "renesas,rskrza1", "renesas,r7s72100" + - RZN1D-DB (RZ/N1D Demo Board for the RZ/N1D 400 pins package) + compatible = "renesas,rzn1d400-db", "renesas,r9a06g032" - Salvator-X (RTP0RC7795SIPB0010S) compatible = "renesas,salvator-x", "renesas,r8a7795" - Salvator-X (RTP0RC7796SIPB0011S) diff --git a/Documentation/devicetree/bindings/arm/ti/k3.txt b/Documentation/devicetree/bindings/arm/ti/k3.txt new file mode 100644 index 000000000000..6a059cabb2da --- /dev/null +++ b/Documentation/devicetree/bindings/arm/ti/k3.txt @@ -0,0 +1,23 @@ +Texas Instruments K3 Multicore SoC architecture device tree bindings +-------------------------------------------------------------------- + +Platforms based on Texas Instruments K3 Multicore SoC architecture +shall follow the following scheme: + +SoCs +---- + +Each device tree root node must specify which exact SoC in K3 Multicore SoC +architecture it uses, using one of the following compatible values: + +- AM654 + compatible = "ti,am654"; + +Boards +------ + +In addition, each device tree root node must specify which one or more +of the following board-specific compatible values: + +- AM654 EVM + compatible = "ti,am654-evm", "ti,am654"; diff --git a/Documentation/devicetree/bindings/arm/xilinx.txt b/Documentation/devicetree/bindings/arm/xilinx.txt index b9043bc35c14..26fe5ecc4332 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.txt +++ b/Documentation/devicetree/bindings/arm/xilinx.txt @@ -8,18 +8,38 @@ Required root node properties: Additional compatible strings: -- Xilinx internal board cc108 +- Adapteva Parallella board + "adapteva,parallella" + +- Avnet MicroZed board + "avnet,zynq-microzed" + "xlnx,zynq-microzed" + +- Avnet ZedBoard board + "avnet,zynq-zed" + "xlnx,zynq-zed" + +- Digilent Zybo board + "digilent,zynq-zybo" + +- Digilent Zybo Z7 board + "digilent,zynq-zybo-z7" + +- Xilinx CC108 internal board "xlnx,zynq-cc108" -- Xilinx internal board zc770 with different FMC cards +- Xilinx ZC702 internal board + "xlnx,zynq-zc702" + +- Xilinx ZC706 internal board + "xlnx,zynq-zc706" + +- Xilinx ZC770 internal board, with different FMC cards "xlnx,zynq-zc770-xm010" "xlnx,zynq-zc770-xm011" "xlnx,zynq-zc770-xm012" "xlnx,zynq-zc770-xm013" -- Digilent Zybo Z7 board - "digilent,zynq-zybo-z7" - --------------------------------------------------------------- Xilinx Zynq UltraScale+ MPSoC Platforms Device Tree Bindings diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index c760ecb81381..5d5bd456d9d9 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -17,7 +17,6 @@ Required properties: - "marvell,armada-380-ahci" - "marvell,armada-3700-ahci" - "snps,dwc-ahci" - - "snps,exynos5440-ahci" - "snps,spear-ahci" - "generic-ahci" - interrupts : <interrupt mapping for SATA IRQ> @@ -30,6 +29,7 @@ compatible: Optional properties: - dma-coherent : Present if dma operations are coherent - clocks : a list of phandle + clock specifier pairs +- resets : a list of phandle + reset specifier pairs - target-supply : regulator for SATA target power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt index e20eac7a3087..4268e17d2411 100644 --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt @@ -8,6 +8,7 @@ Required properties: - "renesas,sata-r8a7791" for R-Car M2-W - "renesas,sata-r8a7793" for R-Car M2-N - "renesas,sata-r8a7795" for R-Car H3 + - "renesas,sata-r8a77965" for R-Car M3-N - "renesas,rcar-gen2-sata" for a generic R-Car Gen2 compatible device - "renesas,rcar-gen3-sata" for a generic R-Car Gen3 compatible device - "renesas,rcar-sata" is deprecated diff --git a/Documentation/devicetree/bindings/bus/sun50i-de2-bus.txt b/Documentation/devicetree/bindings/bus/sun50i-de2-bus.txt new file mode 100644 index 000000000000..87dfb33fb3be --- /dev/null +++ b/Documentation/devicetree/bindings/bus/sun50i-de2-bus.txt @@ -0,0 +1,37 @@ +Device tree bindings for Allwinner A64 DE2 bus + +The Allwinner A64 DE2 is on a special bus, which needs a SRAM region (SRAM C) +to be claimed for enabling the access. + +Required properties: + + - compatible: Should contain "allwinner,sun50i-a64-de2" + - reg: A resource specifier for the register space + - #address-cells: Must be set to 1 + - #size-cells: Must be set to 1 + - ranges: Must be set up to map the address space inside the + DE2, for the sub-blocks of DE2. + - allwinner,sram: the SRAM that needs to be claimed + +Example: + + de2@1000000 { + compatible = "allwinner,sun50i-a64-de2"; + reg = <0x1000000 0x400000>; + allwinner,sram = <&de2_sram 1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x1000000 0x400000>; + + display_clocks: clock@0 { + compatible = "allwinner,sun50i-a64-de2-clk"; + reg = <0x0 0x100000>; + clocks = <&ccu CLK_DE>, + <&ccu CLK_BUS_DE>; + clock-names = "mod", + "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/bus/ti-sysc.txt b/Documentation/devicetree/bindings/bus/ti-sysc.txt index d8ed5b780ed9..91dc2333af01 100644 --- a/Documentation/devicetree/bindings/bus/ti-sysc.txt +++ b/Documentation/devicetree/bindings/bus/ti-sysc.txt @@ -36,6 +36,7 @@ Required standard properties: "ti,sysc-omap-aes" "ti,sysc-mcasp" "ti,sysc-usb-host-fs" + "ti,sysc-dra7-mcan" - reg shall have register areas implemented for the interconnect target module in question such as revision, sysc and syss diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt index 09968ee224d8..8f8f95056f3d 100644 --- a/Documentation/devicetree/bindings/clock/at91-clock.txt +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -17,14 +17,13 @@ Required properties: "atmel,at91sam9x5-clk-slow-rc-osc": at91 internal slow RC oscillator - "atmel,at91rm9200-pmc" or - "atmel,at91sam9g45-pmc" or - "atmel,at91sam9n12-pmc" or - "atmel,at91sam9x5-pmc" or - "atmel,sama5d3-pmc": + "atmel,<chip>-pmc": at91 PMC (Power Management Controller) All at91 specific clocks (clocks defined below) must be child node of the PMC node. + <chip> can be: at91rm9200, at91sam9260, at91sam9261, + at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9x5, + sama5d2, sama5d3 or sama5d4. "atmel,at91sam9x5-clk-slow" (under sckc node) or diff --git a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt deleted file mode 100644 index c7d227c31e95..000000000000 --- a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt +++ /dev/null @@ -1,28 +0,0 @@ -* Samsung Exynos5440 Clock Controller - -The Exynos5440 clock controller generates and supplies clock to various -controllers within the Exynos5440 SoC. - -Required Properties: - -- compatible: should be "samsung,exynos5440-clock". - -- reg: physical base address of the controller and length of memory mapped - region. - -- #clock-cells: should be 1. - -Each clock is assigned an identifier and client nodes can use this identifier -to specify the clock which they consume. - -All available clocks are defined as preprocessor macros in -dt-bindings/clock/exynos5440.h header and can be used in device -tree sources. - -Example: An example of a clock controller node is listed below. - - clock: clock-controller@10010000 { - compatible = "samsung,exynos5440-clock"; - reg = <0x160000 0x10000>; - #clock-cells = <1>; - }; diff --git a/Documentation/devicetree/bindings/cpufreq/cpufreq-exynos5440.txt b/Documentation/devicetree/bindings/cpufreq/cpufreq-exynos5440.txt deleted file mode 100644 index caff1a57436f..000000000000 --- a/Documentation/devicetree/bindings/cpufreq/cpufreq-exynos5440.txt +++ /dev/null @@ -1,28 +0,0 @@ - -Exynos5440 cpufreq driver -------------------- - -Exynos5440 SoC cpufreq driver for CPU frequency scaling. - -Required properties: -- interrupts: Interrupt to know the completion of cpu frequency change. -- operating-points: Table of frequencies and voltage CPU could be transitioned into, - in the decreasing order. Frequency should be in KHz units and voltage - should be in microvolts. - -Optional properties: -- clock-latency: Clock monitor latency in microsecond. - -All the required listed above must be defined under node cpufreq. - -Example: --------- - cpufreq@160000 { - compatible = "samsung,exynos5440-cpufreq"; - reg = <0x160000 0x1000>; - interrupts = <0 57 0>; - operating-points = < - 1000000 975000 - 800000 925000>; - clock-latency = <100000>; - }; diff --git a/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt index f79641bd5f18..45ffd6c41748 100644 --- a/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt +++ b/Documentation/devicetree/bindings/display/marvell,pxa2xx-lcdc.txt @@ -10,6 +10,9 @@ Required properties: - interrupts : framebuffer controller interrupt. - clocks: phandle to input clocks +Optional properties: + - lcd-supply: A phandle to a power regulator that controls the LCD voltage. + Required nodes: - port: connection to the LCD panel (see video-interfaces.txt) This node must have its properties bus-width and remote-endpoint set. diff --git a/Documentation/devicetree/bindings/display/marvell,pxa300-gcu.txt b/Documentation/devicetree/bindings/display/marvell,pxa300-gcu.txt new file mode 100644 index 000000000000..9cfae5c4e8ec --- /dev/null +++ b/Documentation/devicetree/bindings/display/marvell,pxa300-gcu.txt @@ -0,0 +1,17 @@ +PXA3xx GCU Controller +--------------------- + +Required properties: + - compatible : "marvell,pxa300-gcu" + - reg : should contain the register range (address and length). + - interrupts : Controller interrupt. + - clocks: phandle to the PXA specific input clock. + +Example for PXA300: + + display-controller@54000000 { + compatible = "marvell,pxa300-gcu"; + reg = <0x54000000 0x1000>; + interrupts = <39>; + clocks = <&clks CLK_PXA300_GCU>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index 697ca2f26d1b..a046ed374d80 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -13,6 +13,7 @@ Required properties: - "renesas,irqc-r8a7792" (R-Car V2H) - "renesas,irqc-r8a7793" (R-Car M2-N) - "renesas,irqc-r8a7794" (R-Car E2) + - "renesas,intc-ex-r8a774a1" (RZ/G2M) - "renesas,intc-ex-r8a7795" (R-Car H3) - "renesas,intc-ex-r8a7796" (R-Car M3-W) - "renesas,intc-ex-r8a77965" (R-Car M3-N) diff --git a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt index b0a8af51c388..265b223cd978 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt @@ -11,7 +11,7 @@ The RISC-V supervisor ISA manual specifies three interrupt sources that are attached to every HLIC: software interrupts, the timer interrupt, and external interrupts. Software interrupts are used to send IPIs between cores. The timer interrupt comes from an architecturally mandated real-time timer that is -controller via Supervisor Binary Interface (SBI) calls and CSR reads. External +controlled via Supervisor Binary Interface (SBI) calls and CSR reads. External interrupts connect all other device interrupts to the HLIC, which are routed via the platform-level interrupt controller (PLIC). @@ -25,7 +25,15 @@ in the system. Required properties: - compatible : "riscv,cpu-intc" -- #interrupt-cells : should be <1> +- #interrupt-cells : should be <1>. The interrupt sources are defined by the + RISC-V supervisor ISA manual, with only the following three interrupts being + defined for supervisor mode: + - Source 1 is the supervisor software interrupt, which can be sent by an SBI + call and is reserved for use by software. + - Source 5 is the supervisor timer interrupt, which can be configured by + SBI calls and implements a one-shot timer. + - Source 9 is the supervisor external interrupt, which chains to all other + device interrupts. - interrupt-controller : Identifies the node as an interrupt controller Furthermore, this interrupt-controller MUST be embedded inside the cpu @@ -38,7 +46,7 @@ An example device tree entry for a HLIC is show below. ... cpu1-intc: interrupt-controller { #interrupt-cells = <1>; - compatible = "riscv,cpu-intc", "sifive,fu540-c000-cpu-intc"; + compatible = "sifive,fu540-c000-cpu-intc", "riscv,cpu-intc"; interrupt-controller; }; }; diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt index 53c20cae309f..df5db732138d 100644 --- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -40,6 +40,7 @@ video decode local arbiter, all these ports are according to the video HW. Required properties: - compatible : must be one of the following string: "mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW. + "mediatek,mt2712-m4u" for mt2712 which uses generation two m4u HW. "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW. - reg : m4u register base and size. - interrupts : the interrupt of m4u. @@ -50,8 +51,9 @@ Required properties: according to the local arbiter index, like larb0, larb1, larb2... - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as defined in - dt-binding/memory/mt2701-larb-port.h for mt2701 and - dt-binding/memory/mt8173-larb-port.h for mt8173 + dt-binding/memory/mt2701-larb-port.h for mt2701, + dt-binding/memory/mt2712-larb-port.h for mt2712, and + dt-binding/memory/mt8173-larb-port.h for mt8173. Example: iommu: iommu@10205000 { diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index ffadb7c6f1f3..c6e2d855fe13 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -19,7 +19,10 @@ Required Properties: - "renesas,ipmmu-r8a7794" for the R8A7794 (R-Car E2) IPMMU. - "renesas,ipmmu-r8a7795" for the R8A7795 (R-Car H3) IPMMU. - "renesas,ipmmu-r8a7796" for the R8A7796 (R-Car M3-W) IPMMU. + - "renesas,ipmmu-r8a77965" for the R8A77965 (R-Car M3-N) IPMMU. - "renesas,ipmmu-r8a77970" for the R8A77970 (R-Car V3M) IPMMU. + - "renesas,ipmmu-r8a77980" for the R8A77980 (R-Car V3H) IPMMU. + - "renesas,ipmmu-r8a77990" for the R8A77990 (R-Car E3) IPMMU. - "renesas,ipmmu-r8a77995" for the R8A77995 (R-Car D3) IPMMU. - "renesas,ipmmu-vmsa" for generic R-Car Gen2 or RZ/G1 VMSA-compatible IPMMU. diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt index aa614b2d7cab..615abdd0eb0d 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt @@ -2,8 +2,9 @@ SMI (Smart Multimedia Interface) Common The hardware block diagram please check bindings/iommu/mediatek,iommu.txt -Mediatek SMI have two generations of HW architecture, mt8173 uses the second -generation of SMI HW while mt2701 uses the first generation HW of SMI. +Mediatek SMI have two generations of HW architecture, mt2712 and mt8173 use +the second generation of SMI HW while mt2701 uses the first generation HW of +SMI. There's slight differences between the two SMI, for generation 2, the register which control the iommu port is at each larb's register base. But @@ -15,6 +16,7 @@ not needed for SMI generation 2. Required properties: - compatible : must be one of : "mediatek,mt2701-smi-common" + "mediatek,mt2712-smi-common" "mediatek,mt8173-smi-common" - reg : the register and size of the SMI block. - power-domains : a phandle to the power domain of this local arbiter. diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index ddf46b8856a5..083155cdc2a0 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -4,8 +4,9 @@ The hardware block diagram please check bindings/iommu/mediatek,iommu.txt Required properties: - compatible : must be one of : - "mediatek,mt8173-smi-larb" "mediatek,mt2701-smi-larb" + "mediatek,mt2712-smi-larb" + "mediatek,mt8173-smi-larb" - reg : the register and size of this local arbiter. - mediatek,smi : a phandle to the smi_common node. - power-domains : a phandle to the power domain of this local arbiter. @@ -15,7 +16,7 @@ Required properties: the register. - "smi" : It's the clock for transfer data and command. -Required property for mt2701: +Required property for mt2701 and mt2712: - mediatek,larb-id :the hardware id of this larb. Example: diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt index 132e0007d7d6..e9cb3ec5e502 100644 --- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt +++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt @@ -16,6 +16,8 @@ Required properties: * "allwinner,sun9i-a80-mmc" * "allwinner,sun50i-a64-emmc" * "allwinner,sun50i-a64-mmc" + * "allwinner,sun50i-h6-emmc", "allwinner.sun50i-a64-emmc" + * "allwinner,sun50i-h6-mmc", "allwinner.sun50i-a64-mmc" - reg : mmc controller base registers - clocks : a list with 4 phandle + clock specifier pairs - clock-names : must contain "ahb", "mmc", "output" and "sample" diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt index cfe724398a12..5bb3a18cc38d 100644 --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt @@ -19,8 +19,6 @@ Required properties: - reset-names: must be "stmmaceth" - phy-mode: See ethernet.txt - phy-handle: See ethernet.txt -- #address-cells: shall be 1 -- #size-cells: shall be 0 - syscon: A phandle to the device containing the EMAC or GMAC clock register Optional properties: @@ -86,8 +84,6 @@ emac: ethernet@1c0b000 { reset-names = "stmmaceth"; clocks = <&ccu CLK_BUS_EMAC>; clock-names = "stmmaceth"; - #address-cells = <1>; - #size-cells = <0>; phy-handle = <&int_mii_phy>; phy-mode = "mii"; @@ -137,8 +133,6 @@ emac: ethernet@1c0b000 { reset-names = "stmmaceth"; clocks = <&ccu CLK_BUS_EMAC>; clock-names = "stmmaceth"; - #address-cells = <1>; - #size-cells = <0>; phy-handle = <&ext_rgmii_phy>; phy-mode = "rgmii"; @@ -191,8 +185,6 @@ emac: ethernet@1c0b000 { reset-names = "stmmaceth"; clocks = <&ccu CLK_BUS_EMAC>; clock-names = "stmmaceth"; - #address-cells = <1>; - #size-cells = <0>; phy-handle = <&ext_rgmii_phy>; phy-mode = "rgmii"; diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt index 5b937403fed6..92f399ec22b8 100644 --- a/Documentation/devicetree/bindings/net/nfc/pn544.txt +++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt @@ -2,7 +2,7 @@ Required properties: - compatible: Should be "nxp,pn544-i2c". -- clock-frequency: I²C work frequency. +- clock-frequency: I²C work frequency. - reg: address on the bus - interrupts: GPIO interrupt to which the chip is connected - enable-gpios: Output GPIO pin used for enabling/disabling the PN544 diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt index 3899d6a557c1..576ad002bc83 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt @@ -16,7 +16,10 @@ modes in device tree. Required properties: -- compatible: Should be "fsl,vf610-ftm-pwm". +- compatible : should be "fsl,<soc>-ftm-pwm" and one of the following + compatible strings: + - "fsl,vf610-ftm-pwm" for PWM compatible with the one integrated on VF610 + - "fsl,imx8qm-ftm-pwm" for PWM compatible with the one integrated on i.MX8QM - reg: Physical base address and length of the controller's registers - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt index ef8bd3cb67ab..991728cb46cb 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt @@ -5,11 +5,13 @@ Required properties: - "mediatek,mt2712-pwm": found on mt2712 SoC. - "mediatek,mt7622-pwm": found on mt7622 SoC. - "mediatek,mt7623-pwm": found on mt7623 SoC. + - "mediatek,mt7628-pwm": found on mt7628 SoC. - reg: physical base address and length of the controller's registers. - #pwm-cells: must be 2. See pwm.txt in this directory for a description of the cell format. - clocks: phandle and clock specifier of the PWM reference clock. - - clock-names: must contain the following: + - clock-names: must contain the following, except for MT7628 which + has no clocks - "top": the top clock generator - "main": clock used by the PWM core - "pwm1-8": the eight per PWM clocks for mt2712 diff --git a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt index 35a3b9761ee5..e1ef6afbe3a7 100644 --- a/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt +++ b/Documentation/devicetree/bindings/pwm/renesas,pwm-rcar.txt @@ -12,6 +12,7 @@ Required Properties: - "renesas,pwm-r8a7795": for R-Car H3 - "renesas,pwm-r8a7796": for R-Car M3-W - "renesas,pwm-r8a77965": for R-Car M3-N + - "renesas,pwm-r8a77990": for R-Car E3 - "renesas,pwm-r8a77995": for R-Car D3 - reg: base address and length of the registers block for the PWM. - #pwm-cells: should be 2. See pwm.txt in this directory for a description of diff --git a/Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt b/Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt index 16291f2a4688..bac4afa3b197 100644 --- a/Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt +++ b/Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt @@ -49,7 +49,7 @@ compatible (optional) - standard definition - may contain the following strings: - shared-dma-pool: This indicates a region of memory meant to be used as a shared pool of DMA buffers for a set of devices. It can - be used by an operating system to instanciate the necessary pool + be used by an operating system to instantiate the necessary pool management subsystem if necessary. - vendor specific string in the form <vendor>,[<device>-]<usage> no-map (optional) - empty property diff --git a/Documentation/devicetree/bindings/reset/amlogic,meson-axg-audio-arb.txt b/Documentation/devicetree/bindings/reset/amlogic,meson-axg-audio-arb.txt new file mode 100644 index 000000000000..26e542eb96df --- /dev/null +++ b/Documentation/devicetree/bindings/reset/amlogic,meson-axg-audio-arb.txt @@ -0,0 +1,21 @@ +* Amlogic audio memory arbiter controller + +The Amlogic Audio ARB is a simple device which enables or +disables the access of Audio FIFOs to DDR on AXG based SoC. + +Required properties: +- compatible: 'amlogic,meson-axg-audio-arb' +- reg: physical base address of the controller and length of memory + mapped region. +- clocks: phandle to the fifo peripheral clock provided by the audio + clock controller. +- #reset-cells: must be 1. + +Example on the A113 SoC: + +arb: reset-controller@280 { + compatible = "amlogic,meson-axg-audio-arb"; + reg = <0x0 0x280 0x0 0x4>; + #reset-cells = <1>; + clocks = <&clkc_audio AUD_CLKID_DDR_ARB>; +}; diff --git a/Documentation/devicetree/bindings/reset/qcom,aoss-reset.txt b/Documentation/devicetree/bindings/reset/qcom,aoss-reset.txt new file mode 100644 index 000000000000..510c748656ec --- /dev/null +++ b/Documentation/devicetree/bindings/reset/qcom,aoss-reset.txt @@ -0,0 +1,52 @@ +Qualcomm AOSS Reset Controller +====================================== + +This binding describes a reset-controller found on AOSS-CC (always on subsystem) +for Qualcomm SDM845 SoCs. + +Required properties: +- compatible: + Usage: required + Value type: <string> + Definition: must be: + "qcom,sdm845-aoss-cc" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: must specify the base address and size of the register + space. + +- #reset-cells: + Usage: required + Value type: <uint> + Definition: must be 1; cell entry represents the reset index. + +Example: + +aoss_reset: reset-controller@c2a0000 { + compatible = "qcom,sdm845-aoss-cc"; + reg = <0xc2a0000 0x31000>; + #reset-cells = <1>; +}; + +Specifying reset lines connected to IP modules +============================================== + +Device nodes that need access to reset lines should +specify them as a reset phandle in their corresponding node as +specified in reset.txt. + +For list of all valid reset indicies see +<dt-bindings/reset/qcom,sdm845-aoss.h> + +Example: + +modem-pil@4080000 { + ... + + resets = <&aoss_reset AOSS_CC_MSS_RESTART>; + reset-names = "mss_restart"; + + ... +}; diff --git a/Documentation/devicetree/bindings/reset/uniphier-reset.txt b/Documentation/devicetree/bindings/reset/uniphier-reset.txt index 93efed629900..101743dda223 100644 --- a/Documentation/devicetree/bindings/reset/uniphier-reset.txt +++ b/Documentation/devicetree/bindings/reset/uniphier-reset.txt @@ -118,3 +118,59 @@ Example: other nodes ... }; + + +USB3 core reset +--------------- + +USB3 core reset belongs to USB3 glue layer. Before using the core reset, +it is necessary to control the clocks and resets to enable this layer. +These clocks and resets should be described in each property. + +Required properties: +- compatible: Should be + "socionext,uniphier-pro4-usb3-reset" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-reset" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-reset" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-reset" - for PXs3 SoC +- #reset-cells: Should be 1. +- reg: Specifies offset and length of the register set for the device. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: Should contain + "gio", "link" - for Pro4 SoC + "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: Should contain + "gio", "link" - for Pro4 SoC + "link" - for others + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_rst: reset@0 { + compatible = "socionext,uniphier-ld20-usb3-reset"; + reg = <0x0 0x4>; + #reset-cells = <1>; + clock-names = "link"; + clocks = <&sys_clk 14>; + reset-names = "link"; + resets = <&sys_rst 14>; + }; + + regulator { + ... + }; + + phy { + ... + }; + ... + }; diff --git a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt index bf80e3f96f8c..f9987c30f0d5 100644 --- a/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt +++ b/Documentation/devicetree/bindings/soc/mediatek/pwrap.txt @@ -19,6 +19,7 @@ IP Pairing Required properties in pwrap device node. - compatible: "mediatek,mt2701-pwrap" for MT2701/7623 SoCs + "mediatek,mt6797-pwrap" for MT6797 SoCs "mediatek,mt7622-pwrap" for MT7622 SoCs "mediatek,mt8135-pwrap" for MT8135 SoCs "mediatek,mt8173-pwrap" for MT8173 SoCs diff --git a/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt b/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt index 93b982e9419f..feef39b4a4fd 100644 --- a/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt +++ b/Documentation/devicetree/bindings/sound/mrvl,pxa-ssp.txt @@ -17,20 +17,18 @@ Example: /* upstream device */ - ssp0: ssp@41000000 { + ssp1: ssp@41000000 { compatible = "mrvl,pxa3xx-ssp"; reg = <0x41000000 0x40>; interrupts = <24>; clock-names = "pxa27x-ssp.0"; - dmas = <&dma 13 - &dma 14>; - dma-names = "rx", "tx"; }; /* DAI as user */ ssp_dai0: ssp_dai@0 { compatible = "mrvl,pxa-ssp-dai"; - port = <&ssp0>; + port = <&ssp1>; + #sound-dai-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/sram/sunxi-sram.txt b/Documentation/devicetree/bindings/sram/sunxi-sram.txt index d087f04a4d7f..c51ade86578c 100644 --- a/Documentation/devicetree/bindings/sram/sunxi-sram.txt +++ b/Documentation/devicetree/bindings/sram/sunxi-sram.txt @@ -10,8 +10,14 @@ Controller Node Required properties: - compatible : should be: - - "allwinner,sun4i-a10-sram-controller" - - "allwinner,sun50i-a64-sram-controller" + - "allwinner,sun4i-a10-sram-controller" (deprecated) + - "allwinner,sun4i-a10-system-control" + - "allwinner,sun5i-a13-system-control" + - "allwinner,sun7i-a20-system-control", "allwinner,sun4i-a10-system-control" + - "allwinner,sun8i-a23-system-control" + - "allwinner,sun8i-h3-system-control" + - "allwinner,sun50i-a64-sram-controller" (deprecated) + - "allwinner,sun50i-a64-system-control" - reg : sram controller register offset + length SRAM nodes @@ -26,8 +32,25 @@ once again the representation described in the mmio-sram binding. The valid sections compatible for A10 are: - allwinner,sun4i-a10-sram-a3-a4 + - allwinner,sun4i-a10-sram-c1 - allwinner,sun4i-a10-sram-d +The valid sections compatible for A13 are: + - allwinner,sun5i-a13-sram-a3-a4, allwinner,sun4i-a10-sram-a3-a4 + - allwinner,sun5i-a13-sram-c1, allwinner,sun4i-a10-sram-c1 + - allwinner,sun5i-a13-sram-d, allwinner,sun4i-a10-sram-d + +The valid sections compatible for A20 are: + - allwinner,sun7i-a20-sram-a3-a4, allwinner,sun4i-a10-sram-a3-a4 + - allwinner,sun7i-a20-sram-c1, allwinner,sun4i-a10-sram-c1 + - allwinner,sun7i-a20-sram-d, allwinner,sun4i-a10-sram-d + +The valid sections compatible for A23/A33 are: + - allwinner,sun8i-a23-sram-c1, allwinner,sun4i-a10-sram-c1 + +The valid sections compatible for H3 are: + - allwinner,sun8i-h3-sram-c1, allwinner,sun4i-a10-sram-c1 + The valid sections compatible for A64 are: - allwinner,sun50i-a64-sram-c @@ -47,8 +70,8 @@ This valid values for this argument are: Example ------- -sram-controller@1c00000 { - compatible = "allwinner,sun4i-a10-sram-controller"; +system-control@1c00000 { + compatible = "allwinner,sun4i-a10-system-control"; reg = <0x01c00000 0x30>; #address-cells = <1>; #size-cells = <1>; diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index cc553f0952c5..eb7ee91556a5 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -97,8 +97,8 @@ get assigned to trip points of the zone. The cooling devices are expected to be loaded in the target system. Required properties: -- cooling-device: A phandle of a cooling device with its specifier, - Type: phandle + referring to which cooling device is used in this +- cooling-device: A list of phandles of cooling devices with their specifiers, + Type: phandle + referring to which cooling devices are used in this cooling specifier binding. In the cooling specifier, the first cell is the minimum cooling state and the second cell is the maximum cooling state used in this map. @@ -276,12 +276,7 @@ thermal-zones { }; map1 { trip = <&cpu_alert1>; - cooling-device = <&fan0 5 THERMAL_NO_LIMIT>; - }; - map2 { - trip = <&cpu_alert1>; - cooling-device = - <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + cooling-device = <&fan0 5 THERMAL_NO_LIMIT>, <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; }; }; }; diff --git a/Documentation/devicetree/bindings/timer/ti,davinci-timer.txt b/Documentation/devicetree/bindings/timer/ti,davinci-timer.txt new file mode 100644 index 000000000000..29bf91ccf5b7 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/ti,davinci-timer.txt @@ -0,0 +1,37 @@ +* Device tree bindings for Texas Instruments DaVinci timer + +This document provides bindings for the 64-bit timer in the DaVinci +architecture devices. The timer can be configured as a general-purpose 64-bit +timer, dual general-purpose 32-bit timers. When configured as dual 32-bit +timers, each half can operate in conjunction (chain mode) or independently +(unchained mode) of each other. + +The timer is a free running up-counter and can generate interrupts when the +counter reaches preset counter values. + +Also see ../watchdog/davinci-wdt.txt for timers that are configurable as +watchdog timers. + +Required properties: + +- compatible : should be "ti,da830-timer". +- reg : specifies base physical address and count of the registers. +- interrupts : interrupts generated by the timer. +- interrupt-names: should be "tint12", "tint34", "cmpint0", "cmpint1", + "cmpint2", "cmpint3", "cmpint4", "cmpint5", "cmpint6", + "cmpint7" ("cmpintX" may be omitted if not present in the + hardware). +- clocks : the clock feeding the timer clock. + +Example: + + clocksource: timer@20000 { + compatible = "ti,da830-timer"; + reg = <0x20000 0x1000>; + interrupts = <21>, <22>, <74>, <75>, <76>, <77>, <78>, <79>, + <80>, <81>; + interrupt-names = "tint12", "tint34", "cmpint0", "cmpint1", + "cmpint2", "cmpint3", "cmpint4", "cmpint5", + "cmpint6", "cmpint7"; + clocks = <&pll0_auxclk>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 2f3620547249..2c3fc512e746 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -142,6 +142,7 @@ geekbuying GeekBuying gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. geniatech Geniatech, Inc. +giantec Giantec Semiconductor, Inc. giantplus Giantplus Technology Co., Ltd. globalscale Globalscale Technologies, Inc. gmt Global Mixed-mode Technology, Inc. @@ -200,6 +201,7 @@ koe Kaohsiung Opto-Electronics Inc. kosagi Sutajio Ko-Usagi PTE Ltd. kyo Kyocera Corporation lacie LaCie +laird Laird PLC lantiq Lantiq Semiconductor lattice Lattice Semiconductor lego LEGO Systems A/S @@ -279,6 +281,7 @@ opalkelly Opal Kelly Incorporated opencores OpenCores.org openrisc OpenRISC.io option Option NV +oranth Shenzhen Oranth Technology Co., Ltd. ORCL Oracle Corporation orisetech Orise Technology ortustech Ortus Technology Co., Ltd. @@ -322,6 +325,7 @@ rohm ROHM Semiconductor Co., Ltd roofull Shenzhen Roofull Technology Co, Ltd samsung Samsung Semiconductor samtec Samtec/Softing company +sancloud Sancloud Ltd sandisk Sandisk Corporation sbs Smart Battery System schindler Schindler @@ -401,6 +405,7 @@ upisemi uPI Semiconductor Corp. urt United Radiant Technology Corporation usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor +vamrs Vamrs Ltd. variscite Variscite Ltd. via VIA Technologies, Inc. virtio Virtual I/O Device Specification, developed by the OASIS consortium |