From 3cf06f4f85aea715e8caf8540760faff2fbf86d6 Mon Sep 17 00:00:00 2001 From: Iwo Mergler Date: Fri, 31 Aug 2012 08:59:48 +1000 Subject: mtd: tests: test for multi-bit error correction This tests ECC biterror recovery on a single NAND page. Mostly intended to test ECC hardware and low-level NAND driver. There are two test modes: 0 - artificially inserting bit errors until the ECC fails This is the default method and fairly quick. It should be independent of the quality of the FLASH. 1 - re-writing the same pattern repeatedly until the ECC fails. This method relies on the physics of NAND FLASH to eventually generate '0' bits if '1' has been written sufficient times. Depending on the NAND, the first bit errors will appear after 1000 or more writes and then will usually snowball, reaching the limits of the ECC quickly. The test stops after 10000 cycles, should your FLASH be exceptionally good and not generate bit errors before that. Try a different page offset in that case. Please note that neither of these tests will significantly 'use up' any FLASH endurance. Only a maximum of two erase operations will be performed. Signed-off-by: Iwo Mergler Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- drivers/mtd/tests/Makefile | 1 + drivers/mtd/tests/mtd_nandbiterrs.c | 460 ++++++++++++++++++++++++++++++++++++ 2 files changed, 461 insertions(+) create mode 100644 drivers/mtd/tests/mtd_nandbiterrs.c (limited to 'drivers/mtd/tests') diff --git a/drivers/mtd/tests/Makefile b/drivers/mtd/tests/Makefile index b44dcab940d8..bd0065c0d359 100644 --- a/drivers/mtd/tests/Makefile +++ b/drivers/mtd/tests/Makefile @@ -6,3 +6,4 @@ obj-$(CONFIG_MTD_TESTS) += mtd_stresstest.o obj-$(CONFIG_MTD_TESTS) += mtd_subpagetest.o obj-$(CONFIG_MTD_TESTS) += mtd_torturetest.o obj-$(CONFIG_MTD_TESTS) += mtd_nandecctest.o +obj-$(CONFIG_MTD_TESTS) += mtd_nandbiterrs.o diff --git a/drivers/mtd/tests/mtd_nandbiterrs.c b/drivers/mtd/tests/mtd_nandbiterrs.c new file mode 100644 index 000000000000..cc8d62cb280c --- /dev/null +++ b/drivers/mtd/tests/mtd_nandbiterrs.c @@ -0,0 +1,460 @@ +/* + * Copyright © 2012 NetCommWireless + * Iwo Mergler + * + * Test for multi-bit error recovery on a NAND page This mostly tests the + * ECC controller / driver. + * + * There are two test modes: + * + * 0 - artificially inserting bit errors until the ECC fails + * This is the default method and fairly quick. It should + * be independent of the quality of the FLASH. + * + * 1 - re-writing the same pattern repeatedly until the ECC fails. + * This method relies on the physics of NAND FLASH to eventually + * generate '0' bits if '1' has been written sufficient times. + * Depending on the NAND, the first bit errors will appear after + * 1000 or more writes and then will usually snowball, reaching the + * limits of the ECC quickly. + * + * The test stops after 10000 cycles, should your FLASH be + * exceptionally good and not generate bit errors before that. Try + * a different page in that case. + * + * Please note that neither of these tests will significantly 'use up' any + * FLASH endurance. Only a maximum of two erase operations will be performed. + * + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; see the file COPYING. If not, write to the Free Software + * Foundation, 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ +#include +#include +#include +#include +#include +#include +#include + +#define msg(FMT, VA...) pr_info("mtd_nandbiterrs: "FMT, ##VA) + +static int dev; +module_param(dev, int, S_IRUGO); +MODULE_PARM_DESC(dev, "MTD device number to use"); + +static unsigned page_offset; +module_param(page_offset, uint, S_IRUGO); +MODULE_PARM_DESC(page_offset, "Page number relative to dev start"); + +static unsigned seed; +module_param(seed, uint, S_IRUGO); +MODULE_PARM_DESC(seed, "Random seed"); + +static int mode; +module_param(mode, int, S_IRUGO); +MODULE_PARM_DESC(mode, "0=incremental errors, 1=overwrite test"); + +static unsigned max_overwrite = 10000; + +static loff_t offset; /* Offset of the page we're using. */ +static unsigned eraseblock; /* Eraseblock number for our page. */ + +/* We assume that the ECC can correct up to a certain number + * of biterrors per subpage. */ +static unsigned subsize; /* Size of subpages */ +static unsigned subcount; /* Number of subpages per page */ + +static struct mtd_info *mtd; /* MTD device */ + +static uint8_t *wbuffer; /* One page write / compare buffer */ +static uint8_t *rbuffer; /* One page read buffer */ + +/* 'random' bytes from known offsets */ +static uint8_t hash(unsigned offset) +{ + unsigned v = offset; + unsigned char c; + v ^= 0x7f7edfd3; + v = v ^ (v >> 3); + v = v ^ (v >> 5); + v = v ^ (v >> 13); + c = v & 0xFF; + /* Reverse bits of result. */ + c = (c & 0x0F) << 4 | (c & 0xF0) >> 4; + c = (c & 0x33) << 2 | (c & 0xCC) >> 2; + c = (c & 0x55) << 1 | (c & 0xAA) >> 1; + return c; +} + +static int erase_block(void) +{ + int err; + struct erase_info ei; + loff_t addr = eraseblock * mtd->erasesize; + + msg("erase_block\n"); + + memset(&ei, 0, sizeof(struct erase_info)); + ei.mtd = mtd; + ei.addr = addr; + ei.len = mtd->erasesize; + + err = mtd_erase(mtd, &ei); + if (err || ei.state == MTD_ERASE_FAILED) { + msg("error %d while erasing\n", err); + if (!err) + err = -EIO; + return err; + } + + return 0; +} + +/* Writes wbuffer to page */ +static int write_page(int log) +{ + int err = 0; + size_t written; + + if (log) + msg("write_page\n"); + + err = mtd_write(mtd, offset, mtd->writesize, &written, wbuffer); + if (err || written != mtd->writesize) { + msg("error: write failed at %#llx\n", (long long)offset); + if (!err) + err = -EIO; + } + + return err; +} + +/* Re-writes the data area while leaving the OOB alone. */ +static int rewrite_page(int log) +{ + int err = 0; + struct mtd_oob_ops ops; + + if (log) + msg("rewrite page\n"); + + ops.mode = MTD_OPS_RAW; /* No ECC */ + ops.len = mtd->writesize; + ops.retlen = 0; + ops.ooblen = 0; + ops.oobretlen = 0; + ops.ooboffs = 0; + ops.datbuf = wbuffer; + ops.oobbuf = NULL; + + err = mtd_write_oob(mtd, offset, &ops); + if (err || ops.retlen != mtd->writesize) { + msg("error: write_oob failed (%d)\n", err); + if (!err) + err = -EIO; + } + + return err; +} + +/* Reads page into rbuffer. Returns number of corrected bit errors (>=0) + * or error (<0) */ +static int read_page(int log) +{ + int err = 0; + size_t read; + struct mtd_ecc_stats oldstats; + + if (log) + msg("read_page\n"); + + /* Saving last mtd stats */ + memcpy(&oldstats, &mtd->ecc_stats, sizeof(oldstats)); + + err = mtd_read(mtd, offset, mtd->writesize, &read, rbuffer); + if (err == -EUCLEAN) + err = mtd->ecc_stats.corrected - oldstats.corrected; + + if (err < 0 || read != mtd->writesize) { + msg("error: read failed at %#llx\n", (long long)offset); + if (err >= 0) + err = -EIO; + } + + return err; +} + +/* Verifies rbuffer against random sequence */ +static int verify_page(int log) +{ + unsigned i, errs = 0; + + if (log) + msg("verify_page\n"); + + for (i = 0; i < mtd->writesize; i++) { + if (rbuffer[i] != hash(i+seed)) { + msg("Error: page offset %u, expected %02x, got %02x\n", + i, hash(i+seed), rbuffer[i]); + errs++; + } + } + + if (errs) + return -EIO; + else + return 0; +} + +#define CBIT(v, n) ((v) & (1 << (n))) +#define BCLR(v, n) ((v) = (v) & ~(1 << (n))) + +/* Finds the first '1' bit in wbuffer starting at offset 'byte' + * and sets it to '0'. */ +static int insert_biterror(unsigned byte) +{ + int bit; + + while (byte < mtd->writesize) { + for (bit = 7; bit >= 0; bit--) { + if (CBIT(wbuffer[byte], bit)) { + BCLR(wbuffer[byte], bit); + msg("Inserted biterror @ %u/%u\n", byte, bit); + return 0; + } + } + byte++; + } + msg("biterror: Failed to find a '1' bit\n"); + return -EIO; +} + +/* Writes 'random' data to page and then introduces deliberate bit + * errors into the page, while verifying each step. */ +static int incremental_errors_test(void) +{ + int err = 0; + unsigned i; + unsigned errs_per_subpage = 0; + + msg("incremental biterrors test\n"); + + for (i = 0; i < mtd->writesize; i++) + wbuffer[i] = hash(i+seed); + + err = write_page(1); + if (err) + goto exit; + + while (1) { + + err = rewrite_page(1); + if (err) + goto exit; + + err = read_page(1); + if (err > 0) + msg("Read reported %d corrected bit errors\n", err); + if (err < 0) { + msg("After %d biterrors per subpage, read reported error %d\n", + errs_per_subpage, err); + err = 0; + goto exit; + } + + err = verify_page(1); + if (err) { + msg("ECC failure, read data is incorrect despite read success\n"); + goto exit; + } + + msg("Successfully corrected %d bit errors per subpage\n", + errs_per_subpage); + + for (i = 0; i < subcount; i++) { + err = insert_biterror(i * subsize); + if (err < 0) + goto exit; + } + errs_per_subpage++; + } + +exit: + return err; +} + + +/* Writes 'random' data to page and then re-writes that same data repeatedly. + This eventually develops bit errors (bits written as '1' will slowly become + '0'), which are corrected as far as the ECC is capable of. */ +static int overwrite_test(void) +{ + int err = 0; + unsigned i; + unsigned max_corrected = 0; + unsigned opno = 0; + /* We don't expect more than this many correctable bit errors per + * page. */ + #define MAXBITS 512 + static unsigned bitstats[MAXBITS]; /* bit error histogram. */ + + memset(bitstats, 0, sizeof(bitstats)); + + msg("overwrite biterrors test\n"); + + for (i = 0; i < mtd->writesize; i++) + wbuffer[i] = hash(i+seed); + + err = write_page(1); + if (err) + goto exit; + + while (opno < max_overwrite) { + + err = rewrite_page(0); + if (err) + break; + + err = read_page(0); + if (err >= 0) { + if (err >= MAXBITS) { + msg("Implausible number of bit errors corrected\n"); + err = -EIO; + break; + } + bitstats[err]++; + if (err > max_corrected) { + max_corrected = err; + msg("Read reported %d corrected bit errors\n", + err); + } + } else { /* err < 0 */ + msg("Read reported error %d\n", err); + err = 0; + break; + } + + err = verify_page(0); + if (err) { + bitstats[max_corrected] = opno; + msg("ECC failure, read data is incorrect despite read success\n"); + break; + } + + opno++; + } + + /* At this point bitstats[0] contains the number of ops with no bit + * errors, bitstats[1] the number of ops with 1 bit error, etc. */ + msg("Bit error histogram (%d operations total):\n", opno); + for (i = 0; i < max_corrected; i++) + msg("Page reads with %3d corrected bit errors: %d\n", + i, bitstats[i]); + +exit: + return err; +} + +static int __init mtd_nandbiterrs_init(void) +{ + int err = 0; + + msg("\n"); + msg("==================================================\n"); + msg("MTD device: %d\n", dev); + + mtd = get_mtd_device(NULL, dev); + if (IS_ERR(mtd)) { + err = PTR_ERR(mtd); + msg("error: cannot get MTD device\n"); + goto exit_mtddev; + } + + if (mtd->type != MTD_NANDFLASH) { + msg("this test requires NAND flash\n"); + err = -ENODEV; + goto exit_nand; + } + + msg("MTD device size %llu, eraseblock=%u, page=%u, oob=%u\n", + (unsigned long long)mtd->size, mtd->erasesize, + mtd->writesize, mtd->oobsize); + + subsize = mtd->writesize >> mtd->subpage_sft; + subcount = mtd->writesize / subsize; + + msg("Device uses %d subpages of %d bytes\n", subcount, subsize); + + offset = page_offset * mtd->writesize; + eraseblock = mtd_div_by_eb(offset, mtd); + + msg("Using page=%u, offset=%llu, eraseblock=%u\n", + page_offset, offset, eraseblock); + + wbuffer = kmalloc(mtd->writesize, GFP_KERNEL); + if (!wbuffer) { + err = -ENOMEM; + goto exit_wbuffer; + } + + rbuffer = kmalloc(mtd->writesize, GFP_KERNEL); + if (!rbuffer) { + err = -ENOMEM; + goto exit_rbuffer; + } + + err = erase_block(); + if (err) + goto exit_error; + + if (mode == 0) + err = incremental_errors_test(); + else + err = overwrite_test(); + + if (err) + goto exit_error; + + /* We leave the block un-erased in case of test failure. */ + err = erase_block(); + if (err) + goto exit_error; + + err = -EIO; + msg("finished successfully.\n"); + msg("==================================================\n"); + +exit_error: + kfree(rbuffer); +exit_rbuffer: + kfree(wbuffer); +exit_wbuffer: + /* Nothing */ +exit_nand: + put_mtd_device(mtd); +exit_mtddev: + return err; +} + +static void __exit mtd_nandbiterrs_exit(void) +{ + return; +} + +module_init(mtd_nandbiterrs_init); +module_exit(mtd_nandbiterrs_exit); + +MODULE_DESCRIPTION("NAND bit error recovery test"); +MODULE_AUTHOR("Iwo Mergler"); +MODULE_LICENSE("GPL"); -- cgit v1.2.3