Age | Commit message (Collapse) | Author | Files | Lines |
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
ipv4: dont create routes on down devices
epic100: hamachi: yellowfin: Fix skb allocation size
sundance: Fix oopses with corrupted skb_shared_info
Revert "ipv4: Allow configuring subnets as local addresses"
USB: mcs7830: return negative if auto negotiate fails
irda: prevent integer underflow in IRLMP_ENUMDEVICES
tcp: fix listening_get_next()
atl1c: Do not use legacy PCI power management
mac80211: fix mesh forwarding
MAINTAINERS: email address change
net: Fix range checks in tcf_valid_offset().
net_sched: sch_sfq: fix allot handling
hostap: remove netif_stop_queue from init
mac80211/rt2x00: add ieee80211_tx_status_ni()
typhoon: memory corruption in typhoon_get_drvinfo()
net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
net_sched: always clone skbs
ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
netlink: fix gcc -Wconversion compilation warning
asix: add USB ID for Logitec LAN-GTJ U2A
...
|
|
In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.
# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3
After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 4465b469008bc03b98a1b8df4e9ae501b6c69d4b.
Conflicts:
net/ipv4/fib_frontend.c
As reported by Ben Greear, this causes regressions:
> Change 4465b469008bc03b98a1b8df4e9ae501b6c69d4b caused rules
> to stop matching the input device properly because the
> FLOWI_FLAG_MATCH_ANY_IIF is always defined in ip_dev_find().
>
> This breaks rules such as:
>
> ip rule add pref 512 lookup local
> ip rule del pref 0 lookup local
> ip link set eth2 up
> ip -4 addr add 172.16.0.102/24 broadcast 172.16.0.255 dev eth2
> ip rule add to 172.16.0.102 iif eth2 lookup local pref 10
> ip rule add iif eth2 lookup 10001 pref 20
> ip route add 172.16.0.0/24 dev eth2 table 10001
> ip route add unreachable 0/0 table 10001
>
> If you had a second interface 'eth0' that was on a different
> subnet, pinging a system on that interface would fail:
>
> [root@ct503-60 ~]# ping 192.168.100.1
> connect: Invalid argument
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the user-provided len is less than the expected offset, the
IRLMP_ENUMDEVICES getsockopt will do a copy_to_user() with a very large
size value. While this isn't be a security issue on x86 because it will
get caught by the access_ok() check, it may leak large amounts of kernel
heap on other architectures. In any event, this patch fixes it.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexey Vlasov found /proc/net/tcp could sometime loop and display
millions of sockets in LISTEN state.
In 2.6.29, when we converted TCP hash tables to RCU, we left two
sk_next() calls in listening_get_next().
We must instead use sk_nulls_next() to properly detect an end of chain.
Reported-by: Alexey Vlasov <renton@renton.name>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Cc: stable@kernel.org [2.6.27+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: handle partial result from get_user_pages
ceph: mark user pages dirty on direct-io reads
ceph: fix null pointer dereference in ceph_init_dentry for nfs reexport
ceph: fix direct-io on non-page-aligned buffers
ceph: fix msgr_init error path
|
|
When deploying SFQ/IFB here at work, I found the allot management was
pretty wrong in sfq, even changing allot from short to int...
We should init allot for each new flow, not using a previous value found
in slot.
Before patch, I saw bursts of several packets per flow, apparently
denying the default "quantum 1514" limit I had on my SFQ class.
class sfq 11:1 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 7p requeues 0
allot 11546
class sfq 11:46 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 1p requeues 0
allot -23873
class sfq 11:78 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 5p requeues 0
allot 11393
After patch, better fairness among each flow, allot limit being
respected, allot is positive :
class sfq 11:e parent 11:
(dropped 0, overlimits 0 requeues 86)
backlog 0b 3p requeues 86
allot 596
class sfq 11:94 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 1468
class sfq 11:a4 parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 4p requeues 0
allot 650
class sfq 11:bb parent 11:
(dropped 0, overlimits 0 requeues 0)
backlog 0b 3p requeues 0
allot 596
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modifies IPsec6 to fragment IPv6 packets that are
locally generated as needed.
This version of the patch only fragments in tunnel mode, so that fragment
headers will not be obscured by ESP in transport mode.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The get_user_pages() helper can return fewer than the requested pages.
Error out in that case, and clean up the partial result.
Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
For read operation, we have to set the argument _write_ of get_user_pages
to 1 since we will write data to pages. Also, we need to SetPageDirty before
releasing these pages.
Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
When loopback device is being brought down, then keep the route table
entries because they are special. The entries in the local table for
linklocal routes and ::1 address should not be purged.
This is a sub optimal solution to the problem and should be replaced
by a better fix in future.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get the sctp partial delivery point using SCTP_PARTIAL_DELIVERY_POINT
socket option should return 0 if success, not -ENOTSUPP.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a missing ntohs() for bridge IPv6 multicast snooping.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Special care is taken inside sk_port_alloc to avoid overwriting
skc_node/skc_nulls_node. We should also avoid overwriting
skc_bind_node/skc_portaddr_node.
The patch fixes the following crash:
BUG: unable to handle kernel paging request at fffffffffffffff0
IP: [<ffffffff812ec6dd>] udp4_lib_lookup2+0xad/0x370
[<ffffffff812ecc22>] __udp4_lib_lookup+0x282/0x360
[<ffffffff812ed63e>] __udp4_lib_rcv+0x31e/0x700
[<ffffffff812bba45>] ? ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ? ip_local_deliver+0x88/0xa0
[<ffffffff812eda35>] udp_rcv+0x15/0x20
[<ffffffff812bba45>] ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ip_local_deliver+0x88/0xa0
[<ffffffff812bb2cd>] ip_rcv_finish+0x32d/0x6f0
[<ffffffff8128c14c>] ? netif_receive_skb+0x99c/0x11c0
[<ffffffff812bb94b>] ip_rcv+0x2bb/0x350
[<ffffffff8128c14c>] netif_receive_skb+0x99c/0x11c0
Signed-off-by: Leonard Crestez <lcrestez@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first big packets sent to a "low-MTU" client correctly
triggers the creation of a temporary route containing the reduced MTU.
But after the temporary route has expired, new ICMP6 "packet too big"
will be sent, rt6_pmtu_discovery will find the previous EXPIRED route
check that its mtu isn't bigger then in icmp packet and do nothing
before the temporary route will not deleted by gc.
I make the simple experiment:
while :; do
time ( dd if=/dev/zero bs=10K count=1 | ssh hostname dd of=/dev/null ) || break;
done
The "time" reports real 0m0.197s if a temporary route isn't expired, but
it reports real 0m52.837s (!!!!) immediately after a temporare route has
expired.
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
pppoe.c: Fix kernel panic caused by __pppoe_xmit
WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
bnx2x: Advance a version number to 1.60.01-0
bnx2x: Fixed a compilation warning
bnx2x: LSO code was broken on BE platforms
qlge: Fix deadlock when cancelling worker.
net: fix skb_defer_rx_timestamp()
cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
phy: add the IC+ IP1001 driver
atm: correct sysfs 'device' link creation and parent relationships
MAINTAINERS: remove me from tulip
SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
enic: Bug Fix: Pass napi reference to the isr that services receive queue
ipv6: fix nl group when advertising a new link
connector: add module alias
net: Document the kernel_recvmsg() function
r8169: Fix runtime power management
hso: IP checksuming doesn't work on GE0301 option cards
xfrm: Fix xfrm_state_migrate leak
net: Convert netpoll blocking api in bonding driver to be a counter
...
|
|
create_workqueue() returns NULL on failure.
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
On suspend, there might be usb wireless drivers which wrongly trigger
the warning in ieee80211_work_work. If an usb driver doesn't have a
suspend hook, the usb stack will disconnect the device. On disconnect,
a mac80211 driver calls ieee80211_unregister_hw, which calls dev_close,
which calls ieee80211_stop, and in the end calls ieee80211_work_purge->
ieee80211_work_work.
The problem is that this call to ieee80211_work_purge comes after
mac80211 is suspended, triggering the warning even when we don't have
work queued in work_list (the expected case when already suspended),
because it always calls ieee80211_work_work.
So, just call ieee80211_work_work in ieee80211_work_purge if we really
have to abort work. This addresses the warning reported at
https://bugzilla.kernel.org/show_bug.cgi?id=24402
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
dev_open will eventually call ieee80211_ibss_join which sets up the
skb used for beacons/probe-responses however it is possible to
receive beacons that attempt to merge before this occurs causing
a null pointer dereference. Check ssid_len as that is the last
thing set in ieee80211_ibss_join.
This occurs quite easily in the presence of adhoc nodes with hidden SSID's
revised previous patch to check further up based on irc feedback
Signed-off-by: Tim Harvey <harvey.tim@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-2.6
|
|
After commit c1f19b51d1d8 (net: support time stamping in phy devices.),
kernel might crash if CONFIG_NETWORK_PHY_TIMESTAMPING=y and
skb_defer_rx_timestamp() handles a packet without an ethernet header.
Fixes kernel bugzilla #24102
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=24102
Reported-and-tested-by: Andrew Watts <akwatts@ymail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ATM subsystem was incorrectly creating the 'device' link for ATM
nodes in sysfs. This led to incorrect device/parent relationships
exposed by sysfs and udev. Instead of rolling the 'device' link by hand
in the generic ATM code, pass each ATM driver's bus device down to the
sysfs code and let sysfs do this stuff correctly.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP_SET_PEER_PRIMARY_ADDR does not accpet v4mapped address, using
v4mapped address in SCTP_SET_PEER_PRIMARY_ADDR socket option will
get -EADDRNOTAVAIL error if v4map is enabled. This patch try to
fix it by mapping v4mapped address to v4 address if allowed.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
New idev are advertised with NL group RTNLGRP_IPV6_IFADDR, but
should use RTNLGRP_IPV6_IFINFO.
Bug was introduced by commit 8d7a76c9.
Signed-off-by: Wang Xuefu <xuefu.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Martin Lucina <mato@kotelna.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xfrm_state_migrate calls kfree instead of xfrm_state_put to free
a failed state. According to git commit 553f9118 this can cause
memory leaks.
Signed-off-by: Thomas Egerer <thomas.egerer@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unconditional use of skb->dev won't work here,
try to fetch the econet device via skb_dst()->dev
instead.
Suggested by Eric Dumazet.
Reported-by: Nelson Elhage <nelhage@ksplice.com>
Tested-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure sysctl_tcp_cookie_size is read once in
tcp_cookie_size_check(), or we might return an illegal value to caller
if sysctl_tcp_cookie_size is changed by another cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: William Allen Simpson <william.allen.simpson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl_tcp_tso_win_divisor might be set to zero while one cpu runs in
tcp_tso_should_defer(). Make sure we dont allow a divide by zero by
reading sysctl_tcp_tso_win_divisor exactly once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mac80211 doesn't handle shared skbs correctly at the moment. As a result
a possible resize can trigger a BUG in pskb_expand_head.
[ 676.030000] Kernel bug detected[#1]:
[ 676.030000] Cpu 0
[ 676.030000] $ 0 : 00000000 00000000 819662ff 00000002
[ 676.030000] $ 4 : 81966200 00000020 00000000 00000020
[ 676.030000] $ 8 : 819662e0 800043c0 00000002 00020000
[ 676.030000] $12 : 3b9aca00 00000000 00000000 00470000
[ 676.030000] $16 : 80ea2000 00000000 00000000 00000000
[ 676.030000] $20 : 818aa200 80ea2018 80ea2000 00000008
[ 676.030000] $24 : 00000002 800ace5c
[ 676.030000] $28 : 8199a000 8199bd20 81938f88 80f180d4
[ 676.030000] Hi : 0000026e
[ 676.030000] Lo : 0000757e
[ 676.030000] epc : 801245e4 pskb_expand_head+0x44/0x1d8
[ 676.030000] Not tainted
[ 676.030000] ra : 80f180d4 ieee80211_skb_resize+0xb0/0x114 [mac80211]
[ 676.030000] Status: 1000a403 KERNEL EXL IE
[ 676.030000] Cause : 10800024
[ 676.030000] PrId : 0001964c (MIPS 24Kc)
[ 676.030000] Modules linked in: mac80211_hwsim rt2800lib rt2x00soc rt2x00pci rt2x00lib mac80211 crc_itu_t crc_ccitt cfg80211 compat arc4 aes_generic deflate ecb cbc [last unloaded: rt2800pci]
[ 676.030000] Process kpktgend_0 (pid: 97, threadinfo=8199a000, task=81879f48, tls=00000000)
[ 676.030000] Stack : ffffffff 00000000 00000000 00000014 00000004 80ea2000 00000000 00000000
[ 676.030000] 818aa200 80f180d4 ffffffff 0000000a 81879f78 81879f48 81879f48 00000018
[ 676.030000] 81966246 80ea2000 818432e0 80f1a420 80203050 81814d98 00000001 81879f48
[ 676.030000] 81879f48 00000018 81966246 818432e0 0000001a 8199bdd4 0000001c 80f1b72c
[ 676.030000] 80203020 8001292c 80ef4aa2 7f10b55d 801ab5b8 81879f48 00000188 80005c90
[ 676.030000] ...
[ 676.030000] Call Trace:
[ 676.030000] [<801245e4>] pskb_expand_head+0x44/0x1d8
[ 676.030000] [<80f180d4>] ieee80211_skb_resize+0xb0/0x114 [mac80211]
[ 676.030000] [<80f1a420>] ieee80211_xmit+0x150/0x22c [mac80211]
[ 676.030000] [<80f1b72c>] ieee80211_subif_start_xmit+0x6f4/0x73c [mac80211]
[ 676.030000] [<8014361c>] pktgen_thread_worker+0xfac/0x16f8
[ 676.030000] [<8002ebe8>] kthread+0x7c/0x88
[ 676.030000] [<80008e0c>] kernel_thread_helper+0x10/0x18
[ 676.030000]
[ 676.030000]
[ 676.030000] Code: 24020001 10620005 2502001f <0200000d> 0804917a 00000000 2502001f 00441023 00531021
Fix this by making a local copy of shared skbs prior to mangeling them.
To avoid copying the skb unnecessarily move the skb_copy call below the
checks that don't need write access to the skb.
Also, move the assignment of nh_pos and h_pos below the skb_copy to point
to the correct skb.
It would be possible to avoid another resize of the copied skb by using
skb_copy_expand instead of skb_copy but that would make the patch more
complex. Also, shared skbs are a corner case right now, so the resize
shouldn't matter much.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Rather than printing the message to the log, use a mib counter to keep
track of the count of occurences of time wait bucket overflow. Reduces
spam in logs.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
x25 does not decrement the network device reference counts on module unload.
Thus unregistering any pre-existing interface after unloading the x25 module
hangs and results in
unregister_netdevice: waiting for tap0 to become free. Usage count = 1
This patch decrements the reference counts of all interfaces in x25_link_free,
the way it is already done in x25_link_device_down for NETDEV_DOWN events.
Signed-off-by: Apollon Oikonomopoulos <apollon@noc.grnet.gr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using the SOCK_DGRAM enum results in
"net-pf-2-proto-SOCK_DGRAM-type-115", so use the numeric value like it
is done in net/dccp.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to drop the mutex and do a dev_put, so set an error code and break like
the other paths, instead of returning directly.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Le dimanche 05 décembre 2010 à 12:23 +0100, Eric Dumazet a écrit :
> Le dimanche 05 décembre 2010 à 09:19 +0100, Eric Dumazet a écrit :
>
> > Hmm..
> >
> > If somebody can explain why RTNL is held in arp_ioctl() (and therefore
> > in arp_req_delete()), we might first remove RTNL use in arp_ioctl() so
> > that your patch can be applied.
> >
> > Right now it is not good, because RTNL wont be necessarly held when you
> > are going to call arp_invalidate() ?
>
> While doing this analysis, I found a refcount bug in llc, I'll send a
> patch for net-2.6
Oh well, of course I must first fix the bug in net-2.6, and wait David
pull the fix in net-next-2.6 before sending this rcu conversion.
Note: this patch should be sent to stable teams (2.6.34 and up)
[PATCH net-2.6] llc: fix a device refcount imbalance
commit abf9d537fea225 (llc: add support for SO_BINDTODEVICE) added one
refcount imbalance in llc_ui_bind(), because dev_getbyhwaddr() doesnt
take a reference on device, while dev_get_by_index() does.
Fix this using RCU locking. And since an RCU conversion will be done for
2.6.38 for dev_getbyhwaddr(), put the rcu_read_lock/unlock exactly at
their final place.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org
Cc: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bug has to do with boundary checks on the initial receive window.
If the initial receive window falls between init_cwnd and the
receive window specified by the user, the initial window is incorrectly
brought down to init_cwnd. The correct behavior is to allow it to
remain unchanged.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
When an xprt is created, it has a refcount of 1, and XPT_BUSY is set.
The refcount is *not* owned by the thread that created the xprt
(as is clear from the fact that creators never put the reference).
Rather, it is owned by the absence of XPT_DEAD. Once XPT_DEAD is set,
(And XPT_BUSY is clear) that initial reference is dropped and the xprt
can be freed.
So when a creator clears XPT_BUSY it is dropping its only reference and
so must not touch the xprt again.
However svc_recv, after calling ->xpo_accept (and so getting an XPT_BUSY
reference on a new xprt), calls svc_xprt_recieved. This clears
XPT_BUSY and then svc_xprt_enqueue - this last without owning a reference.
This is dangerous and has been seen to leave svc_xprt_enqueue working
with an xprt containing garbage.
So we need to hold an extra counted reference over that call to
svc_xprt_received.
For safety, any time we clear XPT_BUSY and then use the xprt again, we
first get a reference, and the put it again afterwards.
Note that svc_close_all does not need this extra protection as there are
no threads running, and the final free can only be called asynchronously
from such a thread.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Due to commit 63ce0900 connections initiated through TTYs created with
"rfcomm bind ..." would have security level BT_SECURITY_SDP instead of
BT_SECURITY_LOW. This would cause instant connection failure between any
two SSP capable devices due to the L2CAP connect request to RFCOMM being
sent before authentication has been performed. This patch fixes the
regression by always initializing the DLC security level to
BT_SECURITY_LOW.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Pavel Emelyanov tried to fix a race between sk_filter_(de|at)tach and
sk_clone() in commit 47e958eac280c263397
Problem is we can have several clones sharing a common sk_filter, and
these clones might want to sk_filter_attach() their own filters at the
same time, and can overwrite old_filter->rcu, corrupting RCU queues.
We can not use filter->rcu without being sure no other thread could do
the same thing.
Switch code to a more conventional ref-counting technique : Do the
atomic decrement immediately and queue one rcu call back when last
reference is released.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's not useful to build LED triggers when there's no LEDs that can be
triggered by them. Therefore, fix up the dependencies so that this
cannot happen, and fix a few users that select triggers to depend on
LEDS_CLASS as well (there is also one user that also selects LEDS_CLASS,
which is OK).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Arnd Hannemann <arnd@arndnet.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-2.6
|
|
I found a problem using an IPv6 over IPv4 tunnel. When CONFIG_IPV6_SIT
was enabled, the packets would be rejected as net/ipv6/sit.c was catching
all IPPROTO_IPV6 packets and returning an ICMP port unreachable error.
I think this patch fixes the problem cleanly. I believe the code in
net/ipv4/tunnel4.c:tunnel4_rcv takes care of it properly if none of the
handlers claim the skb.
Signed-off-by: David McCullough <david_mccullough@mcafee.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ip6_tunnel always assumes it consumes 40 bytes (ip6 hdr) of the mtu of the
underlaying device. So for a normal ethernet bearer, the mtu of the ip6_tunnel is
1460.
However, when creating a tunnel the encap limit option is enabled by default, and it
consumes 8 bytes more, so the true mtu shall be 1452.
I dont really know if this breaks some statement in some RFC, so this is a request for
comments.
Signed-off-by: Anders Franzen <anders.franzen@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Th commit titled "mac80211: clean up rx handling wrt. found_sta"
removed found_sta variable which caused a MIC failure event
to be reported twice for a single failure to supplicant resulted
in STA disconnect.
This should fix WPA specific countermeasures WiFi test case (5.2.17)
issues with mac80211 based drivers which report MIC failure events in
rx status.
Cc: Stable <stable@kernel.org> (2.6.37)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes an curious issue due to insufficient
rx frame filtering.
Saqeb Akhter reported frequent disconnects while streaming
videos over samba: <http://marc.info/?m=128600031109136>
> [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [...]
The reason is that the device generates frames with slightly
bogus SA/TA addresses.
e.g.:
[ 2314.402316] Ignore 9f:1f:31:f8:64:ff
[ 2314.402321] Ignore 9f:1f:31:f8:64:ff
[ 2352.453804] Ignore 0d:1f:31:f8:64:ff
[ 2352.453808] Ignore 0d:1f:31:f8:64:ff
^^ the group-address flag is set!
(the correct SA/TA would be: 00:1f:31:f8:64:ff)
Since the AP does not know from where the frames come, it
generates a DEAUTH response for the (invalid) mcast address.
This mcast deauth frame then passes through all filters and
tricks the stack into thinking that the AP brutally kicked
us!
This patch fixes the problem by simply ignoring
non-broadcast, group-addressed deauth/disassoc frames.
Cc: Jouni Malinen <j@w1.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Saqeb Akhter <saqeb.akhter@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|