| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Replace i_pin_wait, which is only used during synchronous inode flushing
with a bit waitqueue. This trades off a much smaller inode against
slightly slower wakeup performance, and saves 12 (32-bit) or 20 (64-bit)
bytes in the XFS inode.
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
We almost never block on i_flock, the exception is synchronous inode
flushing. Instead of bloating the inode with a 16/24-byte completion
that we abuse as a semaphore just implement it as a bitlock that uses
a bit waitqueue for the rare sleeping path. This primarily is a
tradeoff between a much smaller inode and a faster non-blocking
path vs faster wakeups, and we are much better off with the former.
A small downside is that we will lose lockdep checking for i_flock, but
given that it's always taken inside the ilock that should be acceptable.
Note that for example the inode writeback locking is implemented in a
very similar way.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
We spent a lot of effort to maintain this field, but it always equals to the
fork size divided by the constant size of an extent. The prime use of it is
to assert that the two stay in sync. Just divide the fork size by the extent
size in the few places that we actually use it and remove the overhead
of maintaining it. Also introduce a few helpers to consolidate the places
where we actually care about the value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
Outside the now removed nodelaylog code this field is only used for
asserts and can be safely removed now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
The log item ops aren't nessecarily the biggest exploit vector, but marking
them const is easy enough. Also remove the unused xfs_item_ops_t typedef
while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Resolved conflicts:
fs/xfs/xfs_trans_priv.h:
- deleted struct xfs_ail field xa_flags
- kept field xa_log_flush in struct xfs_ail
fs/xfs/xfs_trans_ail.c:
- in xfsaild_push(), in XFS_ITEM_PUSHBUF case, replaced
"flush_log = 1" with "ailp->xa_log_flush++"
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
There is no reason to keep a reference to the inode even if we unlock
it during transaction commit because we never drop a reference between
the ijoin and commit. Also use this fact to merge xfs_trans_ijoin_ref
back into xfs_trans_ijoin - the third argument decides if an unlock
is needed now.
I'm actually starting to wonder if allowing inodes to be unlocked
at transaction commit really is worth the effort. The only real
benefit is that they can be unlocked earlier when commiting a
synchronous transactions, but that could be solved by doing the
log force manually after the unlock, too.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
We need to check for pinned buffers even in .iop_pushbuf given that inode
items flush into the same buffers that may be pinned directly due operations
on the unlinked inode list operating directly on buffers. To do this add a
return value to .iop_pushbuf that tells the AIL push about this and use
the existing log force mechanisms to unpin it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Tested-by: Stefan Priebe <s.priebe@profihost.ag>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Remove the transaction pointer in the inode. It's only used to avoid
passing down an argument in the bmap code, and for a few asserts in
the transaction code right now.
Also use the local variable ip in a few more places in xfs_inode_item_unlock,
so that it isn't only used for debug builds after the above change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
When inodes are marked stale in a transaction, they are treated
specially when the inode log item is being inserted into the AIL.
It tries to avoid moving the log item forward in the AIL due to a
race condition with the writing the underlying buffer back to disk.
The was "fixed" in commit de25c18 ("xfs: avoid moving stale inodes
in the AIL").
To avoid moving the item forward, we return a LSN smaller than the
commit_lsn of the completing transaction, thereby trying to trick
the commit code into not moving the inode forward at all. I'm not
sure this ever worked as intended - it assumes the inode is already
in the AIL, but I don't think the returned LSN would have been small
enough to prevent moving the inode. It appears that the reason it
worked is that the lower LSN of the inodes meant they were inserted
into the AIL and flushed before the inode buffer (which was moved to
the commit_lsn of the transaction).
The big problem is that with delayed logging, the returning of the
different LSN means insertion takes the slow, non-bulk path. Worse
yet is that insertion is to a position -before- the commit_lsn so it
is doing a AIL traversal on every insertion, and has to walk over
all the items that have already been inserted into the AIL. It's
expensive.
To compound the matter further, with delayed logging inodes are
likely to go from clean to stale in a single checkpoint, which means
they aren't even in the AIL at all when we come across them at AIL
insertion time. Hence these were all getting inserted into the AIL
when they simply do not need to be as inodes marked XFS_ISTALE are
never written back.
Transactional/recovery integrity is maintained in this case by the
other items in the unlink transaction that were modified (e.g. the
AGI btree blocks) and committed in the same checkpoint.
So to fix this, simply unpin the stale inodes directly in
xfs_inode_item_committed() and return -1 to indicate that the AIL
insertion code does not need to do any further processing of these
inodes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
follow these guidelines:
- leave initialization in the declaration block if it fits the line
- move to the code where it's more suitable ('for' init block)
The last chunk was modified from David's original to be a correct
fix for what appeared to be a duplicate initialization.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
When formatting an inode item, we have to allocate a separate buffer
to hold extents when there are delayed allocation extents on the
inode and it is in extent format. The allocation size is derived
from the in-core data fork representation, which accounts for
delayed allocation extents, while the on-disk representation does
not contain any delalloc extents.
As a result of this mismatch, the allocated buffer can be far larger
than needed to hold the real extent list which, due to the fact the
inode is in extent format, is limited to the size of the literal
area of the inode. However, we can have thousands of delalloc
extents, resulting in an allocation size orders of magnitude larger
than is needed to hold all the real extents.
Fix this by limiting the size of the buffer being allocated to the
size of the literal area of the inodes in the filesystem (i.e. the
maximum size an inode fork can grow to).
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
|
|
There is an ABBA deadlock between synchronous inode flushing in
xfs_reclaim_inode and xfs_icluster_free. xfs_icluster_free locks the
buffer, then takes inode ilocks, whilst synchronous reclaim takes
the ilock followed by the buffer lock in xfs_iflush().
To avoid this deadlock, separate the inode cluster buffer locking
semantics from the synchronous inode flush semantics, allowing
callers to attempt to lock the buffer but still issue synchronous IO
if it can get the buffer. This requires xfs_iflush() calls that
currently use non-blocking semantics to pass SYNC_TRYLOCK rather
than 0 as the flags parameter.
This allows xfs_reclaim_inode to avoid the deadlock on the buffer
lock and detect the failure so that it can drop the inode ilock and
restart the reclaim attempt on the inode. This allows
xfs_ifree_cluster to obtain the inode lock, mark the inode stale and
release it and hence defuse the deadlock situation. It also has the
pleasant side effect of avoiding IO in xfs_reclaim_inode when it
tries to next reclaim the inode as it is now marked stale.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
|
|
When inode buffer IO completes, usually all of the inodes are removed from the
AIL. This involves processing them one at a time and taking the AIL lock once
for every inode. When all CPUs are processing inode IO completions, this causes
excessive amount sof contention on the AIL lock.
Instead, change the way we process inode IO completion in the buffer
IO done callback. Allow the inode IO done callback to walk the list
of IO done callbacks and pull all the inodes off the buffer in one
go and then process them as a batch.
Once all the inodes for removal are collected, take the AIL lock
once and do a bulk removal operation to minimise traffic on the AIL
lock.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
When an inode has been marked stale because the cluster is being
freed, we don't want to (re-)insert this inode into the AIL. There
is a race condition where the cluster buffer may be unpinned before
the inode is inserted into the AIL during transaction committed
processing. If the buffer is unpinned before the inode item has been
committed and inserted, then it is possible for the buffer to be
released and hence processthe stale inode callbacks before the inode
is inserted into the AIL.
In this case, we then insert a clean, stale inode into the AIL which
will never get removed by an IO completion. It will, however, get
reclaimed and that triggers an assert in xfs_inode_free()
complaining about freeing an inode still in the AIL.
This race can be avoided by not moving stale inodes forward in the AIL
during transaction commit completion processing. This closes the
race condition by ensuring we never insert clean stale inodes into
the AIL. It is safe to do this because a dirty stale inode, by
definition, must already be in the AIL.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Under heavy multi-way parallel create workloads, the VFS struggles
to write back all the inodes that have been changed in age order.
The bdi flusher thread becomes CPU bound, spending 85% of it's time
in the VFS code, mostly traversing the superblock dirty inode list
to separate dirty inodes old enough to flush.
We already keep an index of all metadata changes in age order - in
the AIL - and continued log pressure will do age ordered writeback
without any extra overhead at all. If there is no pressure on the
log, the xfssyncd will periodically write back metadata in ascending
disk address offset order so will be very efficient.
Hence we can stop marking VFS inodes dirty during transaction commit
or when changing timestamps during transactions. This will keep the
inodes in the superblock dirty list to those containing data or
unlogged metadata changes.
However, the timstamp changes are slightly more complex than this -
there are a couple of places that do unlogged updates of the
timestamps, and the VFS need to be informed of these. Hence add a
new function xfs_trans_ichgtime() for transactional changes,
and leave xfs_ichgtime() for the non-transactional changes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Commit 0fd7275cc42ab734eaa1a2c747e65479bd1e42af ("xfs: fix gcc 4.6
set but not read and unused statement warnings") failed to convert
some code inside XFS_NATIVE_HOST (big endian host code only) and
hence fails to build on such machines. Fix it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
[hch: dropped a few hunks that need structural changes instead]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
|
xfs_iput is just a small wrapper for xfs_iunlock + IRELE. Having this
out of line wrapper means the trace events in those two can't track
their caller properly. So just remove the wrapper and opencode the
unlock + rele in the few callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
By making this member a void pointer we can get rid of a lot of pointless
casts.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Currently we need to either call IHOLD or xfs_trans_ihold on an inode when
joining it to a transaction via xfs_trans_ijoin.
This patches instead makes xfs_trans_ijoin usable on it's own by doing
an implicity xfs_trans_ihold, which also allows us to drop the third
argument. For the case where we want to hold a reference on the inode
a xfs_trans_ijoin_ref wrapper is added which does the IHOLD and marks
the inode for needing an xfs_iput. In addition to the cleaner interface
to the caller this also simplifies the implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Stop the function pointer casting madness and give all the li_cb instances
correct prototype.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Stop the function pointer casting madness and give all the xfs_item_ops the
correct prototypes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
The unpin_remove item operation instances always share most of the
implementation with the respective unpin implementation. So instead
of keeping two different entry points add a remove flag to the unpin
operation and share the code more easily.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
|
|
Dmapi support was never merged upstream, but we still have a lot of hooks
bloating XFS for it, all over the fast pathes of the filesystem.
This patch drops over 700 lines of dmapi overhead. If we'll ever get HSM
support in mainline at least the namespace events can be done much saner
in the VFS instead of the individual filesystem, so it's not like this
is much help for future work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
The staleness of a object being unpinned can be directly derived
from the object itself - there is no need to extract it from the
object then pass it as a parameter into IOP_UNPIN().
This means we can kill the XFS_LID_BUF_STALE flag - it is set,
checked and cleared in the same places XFS_BLI_STALE flag in the
xfs_buf_log_item so it is now redundant and hence safe to remove.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
We don't record pin counts in inode events right now, and this makes
it difficult to track down problems related to pinning inodes. Add
the pin count to the inode trace class and add trace events for
pinning and unpinning inodes.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Each log item type does manual initialisation of the log item.
Delayed logging introduces new fields that need initialisation, so
factor all the open coded initialisation into a common function
first.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Inodes are only pinned/unpinned via the inode item methods, and lots of
code relies on that fact. So remove the separate xfs_ipin/xfs_iunpin
helpers and merge them into their only callers. This also fixes up
various duplicate and/or incorrect comments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
All buffers logged into the AIL are marked as delayed write.
When the AIL needs to push the buffer out, it issues an async write of the
buffer. This means that IO patterns are dependent on the order of
buffers in the AIL.
Instead of flushing the buffer, promote the buffer in the delayed
write list so that the next time the xfsbufd is run the buffer will
be flushed by the xfsbufd. Return the state to the xfsaild that the
buffer was promoted so that the xfsaild knows that it needs to cause
the xfsbufd to run to flush the buffers that were promoted.
Using the xfsbufd for issuing the IO allows us to dispatch all
buffer IO from the one queue. This means that we can make much more
enlightened decisions on what order to flush buffers to disk as
we don't have multiple places issuing IO. Optimisations to xfsbufd
will be in a future patch.
Version 2
- kill XFS_ITEM_FLUSHING as it is now unused.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
We currently do background inode flush asynchronously, resulting in
inodes being written in whatever order the background writeback
issues them. Not only that, there are also blocking and non-blocking
asynchronous inode flushes, depending on where the flush comes from.
This patch completely removes asynchronous inode writeback. It
removes all the strange writeback modes and replaces them with
either a synchronous flush or a non-blocking delayed write flush.
That is, inode flushes will only issue IO directly if they are
synchronous, and background flushing may do nothing if the operation
would block (e.g. on a pinned inode or buffer lock).
Delayed write flushes will now result in the inode buffer sitting in
the delwri queue of the buffer cache to be flushed by either an AIL
push or by the xfsbufd timing out the buffer. This will allow
accumulation of dirty inode buffers in memory and allow optimisation
of inode cluster writeback at the xfsbufd level where we have much
greater queue depths than the block layer elevators. We will also
get adjacent inode cluster buffer IO merging for free when a later
patch in the series allows sorting of the delayed write buffers
before dispatch.
This effectively means that any inode that is written back by
background writeback will be seen as flush locked during AIL
pushing, and will result in the buffers being pushed from there.
This writeback path is currently non-optimal, but the next patch
in the series will fix that problem.
A side effect of this delayed write mechanism is that background
inode reclaim will no longer directly flush inodes, nor can it wait
on the flush lock. The result is that inode reclaim must leave the
inode in the reclaimable state until it is clean. Hence attempts to
reclaim a dirty inode in the background will simply skip the inode
until it is clean and this allows other mechanisms (i.e. xfsbufd) to
do more optimal writeback of the dirty buffers. As a result, the
inode reclaim code has been rewritten so that it no longer relies on
the ambiguous return values of xfs_iflush() to determine whether it
is safe to reclaim an inode.
Portions of this patch are derived from patches by Christoph
Hellwig.
Version 2:
- cleanup reclaim code as suggested by Christoph
- log background reclaim inode flush errors
- just pass sync flags to xfs_iflush
Signed-off-by: Dave Chinner <david@fromorbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Remove the XFS_LOG_FORCE argument which was always set, and the
XFS_LOG_URGE define, which was never used.
Split xfs_log_force into a two helpers - xfs_log_force which forces
the whole log, and xfs_log_force_lsn which forces up to the
specified LSN. The underlying implementations already were entirely
separate, as were the users.
Also re-indent the new _xfs_log_force/_xfs_log_force which
previously had a weird coding style.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
This macro only obsfucates the log item type assignments, so kill it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
Currently we define aliases for the buffer flags in various
namespaces, which only adds confusion. Remove all but the XBF_
flags to clean this up a bit.
Note that we still abuse XFS_B_ASYNC/XBF_ASYNC for some non-buffer
uses, but I'll clean that up later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
Convert the old xfs tracing support that could only be used with the
out of tree kdb and xfsidbg patches to use the generic event tracer.
To use it make sure CONFIG_EVENT_TRACING is enabled and then enable
all xfs trace channels by:
echo 1 > /sys/kernel/debug/tracing/events/xfs/enable
or alternatively enable single events by just doing the same in one
event subdirectory, e.g.
echo 1 > /sys/kernel/debug/tracing/events/xfs/xfs_ihold/enable
or set more complex filters, etc. In Documentation/trace/events.txt
all this is desctribed in more detail. To reads the events do a
cat /sys/kernel/debug/tracing/trace
Compared to the last posting this patch converts the tracing mostly to
the one tracepoint per callsite model that other users of the new
tracing facility also employ. This allows a very fine-grained control
of the tracing, a cleaner output of the traces and also enables the
perf tool to use each tracepoint as a virtual performance counter,
allowing us to e.g. count how often certain workloads git various
spots in XFS. Take a look at
http://lwn.net/Articles/346470/
for some examples.
Also the btree tracing isn't included at all yet, as it will require
additional core tracing features not in mainline yet, I plan to
deliver it later.
And the really nice thing about this patch is that it actually removes
many lines of code while adding this nice functionality:
fs/xfs/Makefile | 8
fs/xfs/linux-2.6/xfs_acl.c | 1
fs/xfs/linux-2.6/xfs_aops.c | 52 -
fs/xfs/linux-2.6/xfs_aops.h | 2
fs/xfs/linux-2.6/xfs_buf.c | 117 +--
fs/xfs/linux-2.6/xfs_buf.h | 33
fs/xfs/linux-2.6/xfs_fs_subr.c | 3
fs/xfs/linux-2.6/xfs_ioctl.c | 1
fs/xfs/linux-2.6/xfs_ioctl32.c | 1
fs/xfs/linux-2.6/xfs_iops.c | 1
fs/xfs/linux-2.6/xfs_linux.h | 1
fs/xfs/linux-2.6/xfs_lrw.c | 87 --
fs/xfs/linux-2.6/xfs_lrw.h | 45 -
fs/xfs/linux-2.6/xfs_super.c | 104 ---
fs/xfs/linux-2.6/xfs_super.h | 7
fs/xfs/linux-2.6/xfs_sync.c | 1
fs/xfs/linux-2.6/xfs_trace.c | 75 ++
fs/xfs/linux-2.6/xfs_trace.h | 1369 +++++++++++++++++++++++++++++++++++++++++
fs/xfs/linux-2.6/xfs_vnode.h | 4
fs/xfs/quota/xfs_dquot.c | 110 ---
fs/xfs/quota/xfs_dquot.h | 21
fs/xfs/quota/xfs_qm.c | 40 -
fs/xfs/quota/xfs_qm_syscalls.c | 4
fs/xfs/support/ktrace.c | 323 ---------
fs/xfs/support/ktrace.h | 85 --
fs/xfs/xfs.h | 16
fs/xfs/xfs_ag.h | 14
fs/xfs/xfs_alloc.c | 230 +-----
fs/xfs/xfs_alloc.h | 27
fs/xfs/xfs_alloc_btree.c | 1
fs/xfs/xfs_attr.c | 107 ---
fs/xfs/xfs_attr.h | 10
fs/xfs/xfs_attr_leaf.c | 14
fs/xfs/xfs_attr_sf.h | 40 -
fs/xfs/xfs_bmap.c | 507 +++------------
fs/xfs/xfs_bmap.h | 49 -
fs/xfs/xfs_bmap_btree.c | 6
fs/xfs/xfs_btree.c | 5
fs/xfs/xfs_btree_trace.h | 17
fs/xfs/xfs_buf_item.c | 87 --
fs/xfs/xfs_buf_item.h | 20
fs/xfs/xfs_da_btree.c | 3
fs/xfs/xfs_da_btree.h | 7
fs/xfs/xfs_dfrag.c | 2
fs/xfs/xfs_dir2.c | 8
fs/xfs/xfs_dir2_block.c | 20
fs/xfs/xfs_dir2_leaf.c | 21
fs/xfs/xfs_dir2_node.c | 27
fs/xfs/xfs_dir2_sf.c | 26
fs/xfs/xfs_dir2_trace.c | 216 ------
fs/xfs/xfs_dir2_trace.h | 72 --
fs/xfs/xfs_filestream.c | 8
fs/xfs/xfs_fsops.c | 2
fs/xfs/xfs_iget.c | 111 ---
fs/xfs/xfs_inode.c | 67 --
fs/xfs/xfs_inode.h | 76 --
fs/xfs/xfs_inode_item.c | 5
fs/xfs/xfs_iomap.c | 85 --
fs/xfs/xfs_iomap.h | 8
fs/xfs/xfs_log.c | 181 +----
fs/xfs/xfs_log_priv.h | 20
fs/xfs/xfs_log_recover.c | 1
fs/xfs/xfs_mount.c | 2
fs/xfs/xfs_quota.h | 8
fs/xfs/xfs_rename.c | 1
fs/xfs/xfs_rtalloc.c | 1
fs/xfs/xfs_rw.c | 3
fs/xfs/xfs_trans.h | 47 +
fs/xfs/xfs_trans_buf.c | 62 -
fs/xfs/xfs_vnodeops.c | 8
70 files changed, 2151 insertions(+), 2592 deletions(-)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
This is picking up on Felix's repost of Dave's patch to implement a
.dirty_inode method. We really need this notification because
the VFS keeps writing directly into the inode structure instead
of going through methods to update this state. In addition to
the long-known atime issue we now also have a caller in VM code
that updates c/mtime that way for shared writeable mmaps. And
I found another one that no one has noticed in practice in the FIFO
code.
So implement ->dirty_inode to set i_update_core whenever the
inode gets externally dirtied, and switch the c/mtime handling to
the same scheme we already use for atime (always picking up
the value from the Linux inode).
Note that this patch also removes the xfs_synchronize_atime call
in xfs_reclaim it was superflous as we already synchronize the time
when writing the inode via the log (xfs_inode_item_format) or the
normal buffers (xfs_iflush_int).
In addition also remove the I_CLEAR check before copying the Linux
timestamps - now that we always have the Linux inode available
we can always use the timestamps in it.
Also switch to just using file_update_time for regular reads/writes -
that will get us all optimization done to it for free and make
sure we notice early when it breaks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
|
|
xfs_trans_iget is a wrapper for xfs_iget that adds the inode to the
transaction after it is read. Except when the inode already is in the
inode cache, in which case it returns the existing locked inode with
increment lock recursion counts.
Now, no one in the tree every decrements these lock recursion counts,
so any user of this gets a potential double unlock when both the original
owner of the inode and the xfs_trans_iget caller unlock it. When looking
back in a git bisect in the historic XFS tree there was only one place
that decremented these counts, xfs_trans_iput. Introduced in commit
ca25df7a840f426eb566d52667b6950b92bb84b5 by Adam Sweeney in 1993,
and removed in commit 19f899a3ab155ff6a49c0c79b06f2f61059afaf3 by
Steve Lord in 2003. And as long as it didn't slip through git bisects
cracks never actually used in that time frame.
A quick audit of the callers of xfs_trans_iget shows that no caller
really relies on this behaviour fortunately - xfs_ialloc allows this
inode from disk so it must not be there before, and all the RT allocator
routines only every add each RT bitmap inode once.
In addition to removing lots of code and reducing the size of the inode
item this patch also avoids the double inode cache lookup in each
create/mkdir/mknod transaction.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
|
|
The guarantees for O_SYNC are exactly the same as the ones we need to
make for an fsync call (and given that Linux O_SYNC is O_DSYNC the
equivalent is fdadatasync, but we treat both the same in XFS), except
with a range data writeout. Jan Kara has started unifying these two
path for filesystems using the generic helpers, and I've started to
look at XFS.
The actual transaction commited by xfs_fsync and xfs_write_sync_logforce
has a different transaction number, but actually is exactly the same.
We'll only use the fsync transaction going forward. One major difference
is that xfs_write_sync_logforce never issues a cache flush unless we
commit a transaction causing that as a side-effect, which is an obvious
bug in the O_SYNC handling. Second all the locking and i_update_size
vs i_update_core changes from 978b7237123d007b9fa983af6e0e2fa8f97f9934
never made it to xfs_write_sync_logforce, so we add them back.
To make xfs_fsync easily usable from the O_SYNC path, the filemap_fdatawait
call is moved up to xfs_file_fsync, so that we don't wait on the whole
file after we already waited for our portion in xfs_write.
We'll also use a plain call to filemap_write_and_wait_range instead
of the previous sync_page_rang which did it in two steps including
an half-hearted inode write out that doesn't help us.
Once we're done with this also remove the now useless i_update_size
tracking.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
|
|
Most uses of struct xfs_imap are to map and inode to a buffer. To avoid
copying around the inode location information we should just embedd a
strcut xfs_imap into the xfs_inode. To make sure it doesn't bloat an
inode the im_len is changed to a ushort, which is fine as that's what
the users exepect anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
|
|
These names don't add any value at all over just using the numerical
values.
(First sent on October 9th)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
|
|
Now that we have a separate xfs_icdinode_t for the in-core inode which
gets logged there is no need anymore for the xfs_dinode vs xfs_dinode_core
split - the fact that part of the structure gets logged through the inode
log item and a small part not can better be described in a comment.
All sizeof operations on the dinode_core either really wanted the
icdinode and are switched to that one, or had already added the size
of the agi unlinked list pointer. Later both will be replaced with
helpers once we get the larger CRC-enabled dinode.
Removing the data and attribute fork unions also has the advantage that
xfs_dinode.h doesn't need to pull in every header under the sun.
While we're at it also add some more comments describing the dinode
structure.
(First sent on October 7th)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
|
|
Change all the remaining AIL API functions that are passed struct
xfs_mount pointers to pass pointers directly to the struct xfs_ail being
used. With this conversion, all external access to the AIL is via the
struct xfs_ail. Hence the operation and referencing of the AIL is almost
entirely independent of the xfs_mount that is using it - it is now much
more tightly tied to the log and the items it is tracking in the log than
it is tied to the xfs_mount.
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32353a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
Add an xfs_ail pointer to log items so that the log items can reference
the AIL directly during callbacks without needed a struct xfs_mount.
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32352a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
Bring the ail lock inside the struct xfs_ail. This means the AIL can be
entirely manipulated via the struct xfs_ail rather than needing both the
struct xfs_mount and the struct xfs_ail.
SGI-PV: 988143
SGI-Modid: xfs-linux-melb:xfs-kern:32350a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
Use the new completion flush code to implement the inode flush lock.
Removes one of the final users of semaphores in the XFS code base.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31817a
Signed-off-by: David Chinner <david@fromorbit.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
kmem_free() function takes (ptr, size) arguments but doesn't actually use
second one.
This patch removes size argument from all callsites.
SGI-PV: 981498
SGI-Modid: xfs-linux-melb:xfs-kern:31050a
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
The writer field is not needed for non_DEBU builds so remove it. While
we're at i also clean up the interface for is locked asserts to go through
and xfs_iget.c helper with an interface like the xfs_ilock routines to
isolated the XFS codebase from mrlock internals. That way we can kill
mrlock_t entirely once rw_semaphores grow an islocked facility. Also
remove unused flags to the ilock family of functions.
SGI-PV: 976035
SGI-Modid: xfs-linux-melb:xfs-kern:30902a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
xfs_bawrite() can return immediate error status on async writes. Unlike
xfsbdstrat() we don't ever check the error on the buffer after the call,
so we currently do not catch errors at all here. Ensure we catch and
propagate or warn to the syslog about up-front async write errors.
SGI-PV: 980084
SGI-Modid: xfs-linux-melb:xfs-kern:30824a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
