summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2007-07-20V4L/DVB (5869): Add check for valid control ID to v4l2_ctrl_next.Hans Verkuil1-5/+14
If v4l2_ctrl_next is called without the V4L2_CTRL_FLAG_NEXT_CTRL then it should check whether the passed control ID is valid and return 0 if it isn't. Otherwise a for-loop over the control IDs will never end. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5866): ivtv: fix DMA timeout when capturing VBI + another streamHans Verkuil1-2/+5
The VBI DMA is handled in a special way and is marked with a bit. However, that bit was set at the wrong time and could be cleared by mistake if a PCM (or other) DMA request would arrive before the VBI DMA was completed. So on completion of the VBI DMA the driver no longer knew that that DMA transfer was for VBI data. And this in turn caused havoc with the card's DMA engine. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5865): Remove usage of HZ on ivtv driver, replacing by msecs_to_jiffiesMauro Carvalho Chehab7-29/+32
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5861): Use msecs_to_jiffies instead of HZ on bttv, cx88 and saa7134Mauro Carvalho Chehab5-6/+6
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5860): Use msecs_to_jiffies instead of HZ on some webcam driversMauro Carvalho Chehab2-3/+3
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5859): use msecs_to_jiffies on InfraRed RC5 timeoutMauro Carvalho Chehab1-2/+2
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5858): Use msecs_to_jiffies instead of HZ on media/video I2C driversMauro Carvalho Chehab4-9/+9
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5857): Use msecs_to_jiffies instead of HZ on radio driversMauro Carvalho Chehab2-3/+3
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5855): ivtv: fix Kconfig typo and refer to the driver homepage.Hans Verkuil1-2/+2
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5854): ivtv: cleanup of driver messagesHans Verkuil5-32/+29
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5853): ivtv: add support to suppress high volume i2c debug messages.Hans Verkuil1-5/+5
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5852): ivtv: don't recompile needlesslyAlexey Dobriyan1-2/+1
Driver prints banner including kernel version. Was a leftover from when the driver was standalone. Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5851): ivtv: fix missing I2C_ALGOBIT config optionHans Verkuil1-0/+1
I2C_ALGOBIT must also be selected when ivtv is selected. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5850): ivtv: improve API command debuggingHans Verkuil1-4/+10
Turn off debugging of API commands that occur during encoding or decoding, unless they are explicitly requested. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20V4L/DVB (5848): Av7110: fix typoYoann Padioleau1-1/+1
Parse error in ifdef or bad use of macro. Signed-off-by: Yoann Padioleau <padator@wanadoo.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
2007-07-20Merge branch 'release' of ↵Linus Torvalds2-33/+41
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] Prevent people from directly including <asm/rwsem.h>. [IA64] remove time interpolator [IA64] Convert to generic timekeeping/clocksource [IA64] refresh some config files for 64K pagesize [IA64] Delete iosapic_free_rte() [IA64] fallocate system call [IA64] Enable percpu vector domain for IA64_DIG [IA64] Enable percpu vector domain for IA64_GENERIC [IA64] Support irq migration across domain [IA64] Add support for vector domain [IA64] Add mapping table between irq and vector [IA64] Check if irq is sharable [IA64] Fix invalid irq vector assumption for iosapic [IA64] Use dynamic irq for iosapic interrupts [IA64] Use per iosapic lock for indirect iosapic register access [IA64] Cleanup lock order in iosapic_register_intr [IA64] Remove duplicated members in iosapic_rte_info [IA64] Remove block structure for locking in iosapic.c
2007-07-20Fix memory leak in tpm_binary_bios_measurements_open()Reiner Sailer1-3/+8
The same problem that was fixed for tpm_ascii_bios_measurements_open() in commit 178554ae75739e91dc4d7c3e42a3db95448cc5bf also occurs in tpm_binary_bios measurements(). Thanks for noticing this Satyam! I tested the attached patch to fix tpm_binary_bios_measurments as well. Signed-off-by: Reiner Sailer <sailer@watson.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20Pull ia64-clocksource into release branchTony Luck2-33/+41
2007-07-20[IA64] Convert to generic timekeeping/clocksourceTony Luck2-33/+41
This is a merge of Peter Keilty's initial patch (which was revived by Bob Picco) for this with Hidetoshi Seto's fixes and scaling improvements. Acked-by: Bob Picco <bob.picco@hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
2007-07-20KVM: MMU: Fix oopses with SLUBAvi Kivity1-13/+26
The kvm mmu uses page->private on shadow page tables; so does slub, and an oops result. Fix by allocating regular pages for shadows instead of using slub. Tested-by: S.Çağlar Onur <caglar@pardus.org.tr> Signed-off-by: Avi Kivity <avi@qumranet.com>
2007-07-20KVM: x86 emulator: implement rdmsr and wrmsrAvi Kivity3-5/+31
Allow real-mode emulation of rdmsr and wrmsr. This allows smp Windows to boot, presumably for its sipi trampoline. Signed-off-by: Avi Kivity <avi@qumranet.com>
2007-07-20KVM: Fix memory slot management functions for guest smpAvi Kivity3-123/+52
The memory slot management functions were oriented against vcpu 0, where they should be kvm-wide. This causes hangs starting X on guest smp. Fix by making the functions (and resultant tail in the mmu) non-vcpu-specific. Unfortunately this reduces the efficiency of the mmu object cache a bit. We may have to revisit this later. Signed-off-by: Avi Kivity <avi@qumranet.com>
2007-07-20KVM: MMU: Store nx bit for large page shadowsAvi Kivity2-2/+4
We need to distinguish between large page shadows which have the nx bit set and those which don't. The problem shows up when booting a newer smp Linux kernel, where the trampoline page (which is in real mode, which uses the same shadow pages as large pages) is using the same mapping as a kernel data page, which is mapped using nx, causing kvm to spin on that page. Signed-off-by: Avi Kivity <avi@qumranet.com>
2007-07-20Merge branch 'master' of ↵Linus Torvalds7-0/+510
git://git.kernel.org/pub/scm/linux/kernel/git/sfr/ofcons * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/ofcons: Create drivers/of/platform.c Create linux/of_platorm.h [SPARC/64] Rename some functions like PowerPC Begin consolidation of of_device.h Begin to consolidate of_device.c Consolidate of_find_node_by routines Consolidate of_get_next_child Consolidate of_get_parent Consolidate of_find_property Consolidate of_device_is_compatible Start split out of common open firmware code Split out common parts of prom.h
2007-07-20Merge branch 'for-linus' of ↵Linus Torvalds10-113/+545
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: appletouch - improve powersaving for Geyser3 devices Input: lifebook - fix an oops on Panasonic CF-18 Input: document intended meaning of KEY_SWITCHVIDEOMODE Input: switch to using seq_list_xxx helpers Input: i8042 - give more trust to PNP data on i386 Input: add driver for Fujitsu serial touchscreens Input: ads7846 - re-check pendown status before reporting events Input: ads7846 - introduce sample settling delay Input: xpad - add support for leds on xbox 360 pad
2007-07-20pata_cs5520: Fix probe bug regression introduced in 2.6.22Alan Cox1-1/+1
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linux Torvalds <torvalds@linux-foundation.org>
2007-07-20lguest: override sched_clockRusty Russell1-1/+8
Guests currently use the default scheduler clock: this means they always use jiffies even if TSC is actually available. It doesn't make any noticeable difference here, but it's a better thing to do. Also remove commented-out asm/sched-clock.h from -mm tree. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20lguest: trivial: We now have asm/processor-flags.h, so use it.Rusty Russell1-3/+1
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20lguest: fix sense if IF flag on interrupt injectionRusty Russell1-5/+5
The sense of the IF bit is backwards in the host interrupt handling. This means we always save "IF=1" on the stack when injecting an interrupt. It turns out this is almost always correct (unless the guest is taking a page fault in an interrupt due to an unpopulated vmalloc mapping), so went unnoticed. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6Linus Torvalds2-2/+2
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits) sh: intc - add support for SH7750 and its variants sh: Move entry point code to .text.head. sh: heartbeat: Shut up resource size warning. sh: update r2d defconfig and fix SH7751R pci compliation sh: Many symbol exports for nommu allmodconfig. sh: zero terminate 8250 platform data for r2d board sh: cpufreq: Fix up the build for SH-2. sh: Make on-chip DMA channel selection explicit. sh: Fix up CPU dependencies for on-chip DMAC. sh: cpufreq: clock framework support. sh: Support rate rounding for SH7722 FRQCR clocks. sh: Implement clk_round_rate() in the clock framework. sh: Fix up PCI section mismatch warnings. sh: Wire up fallocate() syscall. sh: intc - add support for 7780 sh: intc - improve group support sh: Fix up SH-3 and SH-4 driver dependencies. sh: push-switch: Correct license string. sh: cpufreq: Fix driver dependencies and flag as broken. sh: IPR/INTC2 IRQ setup consolidation. ...
2007-07-20Merge branch 'upstream-linus' of ↵Linus Torvalds20-398/+799
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (29 commits) libata: implement EH fast drain libata: schedule probing after SError access failure during autopsy libata: clear HOTPLUG flag after a reset libata: reorganize ata_ehi_hotplugged() libata: improve SCSI scan failure handling libata: quickly trigger SATA SPD down after debouncing failed libata: improve SATA PHY speed down logic The SATA controller device ID is different according to ahci: implement SCR_NOTIFICATION r/w ahci: make NO_NCQ handling more consistent libata: make ->scr_read/write callbacks return error code libata: implement AC_ERR_NCQ libata: improve EH report formatting sata_sil24: separate out sil24_do_softreset() sata_sil24: separate out sil24_exec_polled_cmd() sata_sil24: replace sil24_update_tf() with sil24_read_tf() ahci: separate out ahci_do_softreset() ahci: separate out ahci_exec_polled_cmd() ahci: separate out ahci_kick_engine() ahci: use deadline instead of fixed timeout for 1st FIS for SRST ...
2007-07-20Memory leak in tpm_ascii_bios_measurements_open()Jesper Juhl1-3/+8
Coverity found a memory leak in tpm_ascii_bios_measurements_open(). If "read_log(log)" fails, then we may leak 'log' and 'log->bios_event_log'. Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Cc: Seiji Munetoh <munetoh@jp.ibm.com> Cc: Stefan Berger <stefanb@us.ibm.com> Cc: Reiner Sailer <sailer@watson.ibm.com> Cc: Kylene Hall <kjhall@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20cr_backlight_probe() allocates too little storage for struct cr_panelJesper Juhl1-1/+1
The Coverity checker noticed that we allocate too little storage for "struct cr_panel *crp" in cr_backlight_probe(). Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Cc: Thomas Hellstrom <thomas@tungstengraphics.com> Cc: Alan Hourihane <alanh@tungstengraphics.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20async_tx: fix kmap_atomic usage in async_memcpyDan Williams1-2/+2
Andrew Morton: [async_memcpy] is very wrong if both ASYNC_TX_KMAP_DST and ASYNC_TX_KMAP_SRC can ever be set. We'll end up using the same kmap slot for both src add dest and we get either corrupted data or a BUG. Evgeniy Polyakov: Btw, shouldn't it always be kmap_atomic() even if flag is not set. That pages are usual one returned by alloc_page(). So fix the usage of kmap_atomic and kill the ASYNC_TX_KMAP_DST and ASYNC_TX_KMAP_SRC flags. Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20dpt_i2o depends on virt_to_busStephen Rothwell1-1/+1
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20Merge branch 'master' of ↵Linus Torvalds2-18/+10
master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6 * 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SPARC64]: Fix two year old bug in early bootup asm. [SPARC64]: Update defconfig. [SPARC64]: Fix log message type in vio_create_one(). [SPARC64]: Tweak assertions in sun4v_build_virq(). [SPARC64]: Tweak kernel log messages in power_probe(). [SPARC64]: Fix handling of multiple vdc-port nodes. [SPARC64]: Fix device type matching in VIO's devspec_show(). [SPARC64]: Fix MODULE_DEVICE_TABLE() specification in VDC and VNET. [SPARC]: Add sys_fallocate() entries. [SPARC64]: Use orderly_poweroff().
2007-07-20Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds46-1079/+5344
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (44 commits) USB: drivers/usb/storage/dpcm.c whitespace cleanup USB: r8a66597-hcd: fixes some problem USB: change name of spinlock in hcd.c USB: move routines in hcd.c USB: misc: uss720: clean up urb->status usage USB: misc: usbtest: clean up urb->status usage USB: misc: usblcd: clean up urb->status usage USB: misc: phidgetmotorcontrol: clean up urb->status usage USB: misc: phidgetkit: clean up urb->status usage USB: misc: legousbtower: clean up urb->status usage USB: misc: ldusb: clean up urb->status usage USB: misc: iowarrior: clean up urb->status usage USB: misc: ftdi-elan: clean up urb->status usage USB: misc: auerswald: clean up urb->status usage USB: misc: appledisplay: clean up urb->status usage USB: misc: adtux: clean up urb->status usage USB: core: message: clean up urb->status usage USB: image: microtek: clean up urb->status usage USB: image: mdc800: clean up urb->status usage USB: storage: onetouch: clean up urb->status usage ...
2007-07-20Fix lguest misannotationAl Viro1-1/+1
It's void __user *, not void * __user... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20Fix up sky2 breakageAl Viro1-3/+4
Doing |= 1 << 19 to 16bit unsigned is not particulary useful; that register is 32bit, unlike the ones dealt with in the rest of function, so we need u32 variable here. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20Fix buggered kmalloc() call argument orderAl Viro1-1/+1
Wrong order of arguments Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20m68k: exclude more unbuildable driversAl Viro1-1/+1
anything that wants working dma-mapping won't work parport_pc won't work on m68k unless we have ISA Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20mac89x0: missing __initAl Viro1-1/+1
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20m68k: remove empty ->setup is several consolesAl Viro2-14/+0
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20m68k: missing exportsAl Viro2-0/+9
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20more isa/eisa/pci-only drivers marked as suchAl Viro1-2/+2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20libata: implement EH fast drainTejun Heo3-2/+101
In most cases, when EH is scheduled, all in-flight commands are aborted causing EH to kick in immediately. However, in some cases (especially with PMP), it's unclear which commands are affected by the error condition and although aborting all in-flight commands work, it isn't optimal and may cause unnecessary disruption. On the other hand, waiting for in-flight commands to drain themselves can take up to 30seconds. This patch implements EH fast drain to handle such situations. It gives in-flight commands some time to finish up but doesn't wait for too long. After EH is scheduled, fast drain timer is started and if no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight commands are aborted. If any completion occurred in the interval, the port is given another interval to finish up itself. Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough for finishing up most commands. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: schedule probing after SError access failure during autopsyTejun Heo1-1/+5
If SError isn't accessible, EH can't tell whether hotplug has happened or not. Report SError read failure with AC_ERR_OTHER and schedule probing with hardreset. This will be mainly useful for PMPs. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: clear HOTPLUG flag after a resetTejun Heo1-5/+10
ATA_EHI_HOTPLUGGED is a hint for reset functions indicating the the port might have gone through hotplug/unplug just before entering EH. Reset functions modify their behaviors a bit to handle the situation better - e.g. using longer debouncing delay. Currently, once HOTPLUG is set, it isn't cleared till the end of EH. This is unnecessary and makes EH take longer. Clear the HOTPLUGGED flag after a reset try (successful or not). Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: improve SCSI scan failure handlingTejun Heo3-18/+49
SCSI scan may fail due to memory allocation failure even if EH is not in progress. Due to use of GFP_ATOMIC in SCSI scan path, allocation failure isn't too rare especially while probing multiple devices at once which is the case when a bunch of devices are connected to PMP. This patch moves SCSI scan failure detetion logic from ata_scsi_hotplug() to ata_scsi_scan_host() and implement synchronous scan behavior. The synchronous path sleeps briefly and repeats SCSI scan if some devices aren't attached properly. It contains robust retry loop to minimize the chance of device misdetection during boot and falls back to async retry if everything fails. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20libata: quickly trigger SATA SPD down after debouncing failedTejun Heo2-3/+5
Debouncing failure is a good indicator of basic link problem. Use -EPIPE to indicate debouncing failure and make ata_eh_reset() invoke sata_down_spd_limit() if the error occurs during reset. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-21 14:34:06 +0000