summaryrefslogtreecommitdiff
path: root/drivers/watchdog/sp5100_tco.c
AgeCommit message (Collapse)AuthorFilesLines
2013-03-22watchdog: sp5100_tco: Remove code that may cause a boot failureTakahisa Tanaka1-120/+6
A problem was found on PC's with the SB700 chipset: The PC fails to load BIOS after running the 3.8.x kernel until the power is completely cut off. It occurs in all 3.8.x versions and the mainline version as of 2/4. The issue does not occur with the 3.7.x builds. There are two methods for accessing the watchdog registers. 1. Re-programming a resource address obtained by allocate_resource() to chipset. 2. Use the direct memory-mapped IO access. The method 1 can be used by all the chipsets (SP5100, SB7x0, SB8x0 or later). However, experience shows that only PC with the SB8x0 (or later) chipsets can use the method 2. This patch removes the method 1, because the critical problem was found. That's why the watchdog timer was able to be used on SP5100 and SB7x0 chipsets until now. Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1116835 Link: https://lkml.org/lkml/2013/2/14/271 Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: stable <stable@vger.kernel.org>
2013-03-01watchdog: sp5100_tco: Write back the original value to reserved bits, ↵Takahisa Tanaka1-20/+8
instead of zero In case of SP5100 or SB7x0 chipsets, the sp5100_tco module writes zero to reserved bits. The module, however, shouldn't depend on specific default value, and should perform a read-merge-write operation for the reserved bits. This patch makes the sp5100_tco module perform a read-merge-write operation on all the chipset (sp5100, sb7x0, sb8x0 or later). Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43176 Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com> Tested-by: Paul Menzel <paulepanter@users.sourceforge.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: stable <stable@vger.kernel.org>
2013-03-01watchdog: sp5100_tco: Fix wrong indirect I/O access for getting value of ↵Takahisa Tanaka1-2/+3
reserved bits In case of SB800 or later chipset and re-programming MMIO address(*), sp5100_tco module may read incorrect value of reserved bit, because the module reads a value from an incorrect I/O address. However, this bug doesn't cause a problem, because when re-programming MMIO address, by chance the module writes zero (this is BIOS's default value) to the low three bits of register. * In most cases, PC with SB8x0 or later chipset doesn't need to re-programming MMIO address, because such PC can enable AcpiMmio and can use 0xfed80b00 for watchdog register base address. This patch fixes this bug. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43176 Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com> Tested-by: Paul Menzel <paulepanter@users.sourceforge.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: stable <stable@vger.kernel.org>
2012-12-19watchdog: sp5100_tco: Add SB8x0 chipset supportTakahisa Tanaka1-50/+271
The current sp5100_tco driver only supports SP5100/SB7x0 chipset, doesn't support SB8x0 chipset, because current sp5100_tco driver doesn't know that the offset address for watchdog timer was changed from SB8x0 chipset. The offset address of SP5100 and SB7x0 chipsets are as follows, quote from the AMD SB700/710/750 Register Reference Guide (Page 164) and the AMD SP5100 Register Reference Guide (Page 166). WatchDogTimerControl 69h WatchDogTimerBase0 6Ch WatchDogTimerBase1 6Dh WatchDogTimerBase2 6Eh WatchDogTimerBase3 6Fh In contrast, the offset address of SB8x0 chipset is as follows, quote from AMD SB800-Series Southbridges Register Reference Guide (Page 147). WatchDogTimerEn 48h WatchDogTimerConfig 4Ch So, In the case of SB8x0 chipset, sp5100_tco reads meaningless MMIO address (for example, 0xbafe00) from wrong offset address, and the following message is logged. SP5100 TCO timer: mmio address 0xbafe00 already in use With this patch, sp5100_tco driver supports SB8x0 chipset, and can avoid iomem resource conflict. The processing of this patch is as follows. Step 1) Attempt to get the watchdog base address from indirect I/O (0xCD6 and 0xCD7). - Go to the step 7 if obtained address hasn't conflicted with other resource. But, currently, the address (0xfec000f0) conflicts with the IOAPIC MMIO address, and the following message is logged. SP5100 TCO timer: mmio address 0xfec000f0 already in use 0xfec000f0 is recommended by AMD BIOS Developer's Guide. So, go to the next step. Step 2) Attempt to get the SBResource_MMIO base address from AcpiMmioEN (for SB8x0, PM_Reg:24h) or SBResource_MMIO (SP5100/SB7x0, PCI_Reg:9Ch) register. - Go to the step 7 if these register has enabled by BIOS, and obtained address hasn't conflicted with other resource. - If above condition isn't true, go to the next step. Step 3) Attempt to get the free MMIO address from allocate_resource(). - Go to the step 7 if these register has enabled by BIOS, and obtained address hasn't conflicted with other resource. - Driver initialization has failed if obtained address has conflicted with other resource, and no 'force_addr' parameter is specified. Step 4) Use the specified address If 'force_addr' parameter is specified. - allocate_resource() function may fail, when the PCI bridge device occupies iomem resource from 0xf0000000 to 0xffffffff. To handle such a case, I added 'force_addr' parameter to sp5100_tco driver. With 'force_addr' parameter, sp5100_tco driver directly can assign MMIO address for watchdog timer from free iomem region. Note that It's dangerous to specify wrong address in the 'force_addr' parameter. Example of force_addr parameter use # cat /proc/iomem ...snip... fec00000-fec003ff : IOAPIC 0 <--- free MMIO region fec10000-fec1001f : pnp 00:0b fec20000-fec203ff : IOAPIC 1 ...snip... # cat /etc/modprobe.d/sp5100_tco.conf options sp5100_tco force_addr=0xfec00800 # modprobe sp5100_tco # cat /proc/iomem ...snip... fec00000-fec003ff : IOAPIC 0 fec00800-fec00807 : SP5100 TCO <--- watchdog timer MMIO address fec10000-fec1001f : pnp 00:0b fec20000-fec203ff : IOAPIC 1 ...snip... # - Driver initialization has failed if specified address has conflicted with other resource. Step 5) Disable the watchdog timer - To rewrite the watchdog timer register of the chipset, absolutely guarantee that the watchdog timer is disabled. Step 6) Re-program the watchdog timer MMIO address to chipset. - Re-program the obtained MMIO address in Step 3 or Step 4 to chipset via indirect I/O (0xCD6 and 0xCD7). Step 7) Enable and setup the watchdog timer This patch has worked fine on my test environment (ASUS M4A89GTD-PRO/USB3 and DL165G7). therefore I believe that it's no problem to re-program the MMIO address for watchdog timer to chipset during disabled watchdog. However, I'm not sure about it, because I don't know much about chipset programming. So, any comments will be welcome. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43176 Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl> Tested-by: Paul Menzel <paulepanter@users.sourceforge.net> Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2012-11-28watchdog: remove use of __devexitBill Pemberton1-2/+2
CONFIG_HOTPLUG is going away as an option so __devexit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28watchdog: remove use of __devinitBill Pemberton1-2/+2
CONFIG_HOTPLUG is going away as an option so __devinit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-11-28watchdog: remove use of __devexit_pBill Pemberton1-1/+1
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-05-23watchdog: sp5100_tco.c: quiet sparse noise about using plain integer was ↵H Hartley Sweeten1-1/+1
NULL pointer Pointers should not be compared to plain integers. Quiets the sparse warning: warning: Using plain integer as NULL pointer Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2012-03-27watchdog: nowayout is boolWim Van Sebroeck1-2/+2
nowayout is actually a boolean value. So make it bool for all watchdog device drivers. Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2012-03-27watchdog: Use pr_<fmt> and pr_<level>Joe Perches1-18/+13
Use the current logging styles. Make sure all output has a prefix. Add missing newlines. Remove now unnecessary PFX, NAME, and miscellaneous other #defines. Coalesce formats. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2011-03-29watchdog: sp5100_tco.c: Check if firmware has set correct value in tcobase.Yinghai Lu1-2/+14
Stefano found SP5100 TCO watchdog driver using wrong address. [ 9.148536] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01 [ 9.148628] DEBUG __ioremap_caller WARNING address=b8fe00 size=8 valid=1 reserved=1 and e820 said that range is RAM. We should check if we can use that reading out. BIOS could just program wrong address there. Reported-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by:Yinghai Lu <yinghai@kernel.org> Acked-by: Mike Waychison <mikew@google.com> Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: stable <stable@kernel.org>
2011-03-15watchdog: convert to DEFINE_PCI_DEVICE_TABLEWim Van Sebroeck1-1/+1
Convert static struct pci_device_id *[] to static DEFINE_PCI_DEVICE_TABLE tables. Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2011-01-12watchdog: Add support for sp5100 chipset TCOPriyanka Gupta1-0/+480
This driver adds /dev/watchdog support for the AMD sp5100 aka SB7x0 chipsets. It follows the same conventions found in other /dev/watchdog drivers. Signed-off-by: Priyanka Gupta <priyankag@google.com> Signed-off-by: Mike Waychison <mikew@google.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>