summaryrefslogtreecommitdiff
path: root/drivers/scsi/qedf
AgeCommit message (Collapse)AuthorFilesLines
2019-08-29scsi: qedf: Check for module unloading bit before processing link update AENSaurav Kashyap1-0/+10
Prevent race where we're removing the module and we get link update Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Initiator fails to re-login to switch after link downSaurav Kashyap1-11/+17
Problem Statement: - Driver has fc_id of 0xcc0200 - Driver gets link down (due to test) and calls fcoe_ctlr_link_down(). - At this point, the fc_id of the initiator port is zeroed out. - Driver gets a link up 14 seconds later. - Driver performs FIP VLAN request, gets a response from the switch. - No change in VLAN is detected. - Driver then notifies libfcoe via fcoe_ctlr_link_up(). - Libfcoe then issues a multicast discovery solicitation as expected. - Cisco FCF responds to that correctly. - Libfcoe at this point starts a 3 sec count-down to allow any other FCFs to be discovered. However, at this point, it has been 20 seconds since the last FKA from the driver (which would have been sent prior to backlink toggle), which causes the CVL to be issued from Cisco CVL from the switch is dropped by the driver as the vx_port identification descriptor is present and has value of 0xcc0200, which does not match the driver's value of 0. Libfcoe completes the 3 sec count down and proceeds to issue FLOGI as per protocol. Switch rejects FLogi request. All subsequent FLOGI requests from libfc are rejected by the switch (possibly because it is now expecting a new solicitation). This situation will continue until the next link toggle. Solution: The Vx_port descriptor in the CVL has three fields: MAC address Fabric ID Port Name Today, the code checks for both #1 and #2 above. In the case where we went through a link down, both these will be zero until FLOGI succeeds. We should change our code to check if any one of these 3 is valid and if so, handle the CVL (basically switching from AND to OR). The port name field is definitely expected to be valid always. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Add debug information for unsolicited processingSaurav Kashyap1-0/+5
Log s_id, d_id, type and command to the log message. [mkp: fixed warning] Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Add support for 20 Gbps speedSaurav Kashyap1-0/+5
The current code doeesn't support 20Gbps speed for current and supported speed. Add support for it. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Interpret supported caps value correctlySaurav Kashyap1-5/+27
Driver was wrongly interpreting the supported cap value returned by qed. Solution: Use QED define macros instead of OS defined for interpreting supporting speeds. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Add shutdown callback handlerSaurav Kashyap1-0/+7
Add shutdown callback handler. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Update module description stringNilesh Javali1-1/+1
Update module description. Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Fix crash during sg_resetArun Easi1-2/+2
Driver was attempting to print cdb[0], which is not set for resets coming from SCSI ioctls. Check for cmd_len before accessing cmnd. Crash info: [84790.864747] BUG: unable to handle kernel NULL pointer dereference at (null) [84790.864783] IP: qedf_initiate_tmf+0x7a/0x6e0 [qedf] [84790.865204] Call Trace: [84790.865246] scsi_try_target_reset+0x2b/0x90 [scsi_mod] [84790.865266] scsi_ioctl_reset+0x20f/0x2a0 [scsi_mod] [84790.865284] scsi_ioctl+0x131/0x3a0 [scsi_mod] Signed-off-by: Arun Easi <aeasi@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Stop sending fipvlan request on unloadSaurav Kashyap1-0/+5
- On some setups fipvlan can be retried for long duration and the connection to switch was not there so it was not getting any reply. - During unload this thread was hanging. Problem Resolution: Check if unload is in progress, then quit from fipvlan thread. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-08-29scsi: qedf: Print message during bailout conditionsSaurav Kashyap5-40/+130
Print messages during exiting condition to help debugging. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-07-30net: Use skb_frag_off accessorsJonathan Lemon1-1/+1
Use accessor functions for skb fragment's page_offset instead of direct references, in preparation for bvec conversion. Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller15-60/+15
Honestly all the conflicts were simple overlapping changes, nothing really interesting to report. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-05treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440Thomas Gleixner15-60/+15
Based on 1 normalized pattern(s): this software is available under the terms of the gnu general public license gpl version 2 available from the file copying in the main directory of this source tree extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 35 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190531190115.411886531@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-26qedf: Use hwfns and affin_hwfn_idx to get MSI-X vector index to useChad Dupuis1-11/+28
MSI-X vector index is determined using qed device information and affinity to use. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-21treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner2-0/+2
Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-29scsi: qedf: remove set but not used variablesYueHaibing1-9/+1
Fixes gcc '-Wunused-but-set-variable' warnings: drivers/scsi/qedf/qedf_els.c: In function 'qedf_process_els_compl': drivers/scsi/qedf/qedf_els.c:149:20: warning: variable 'sc_cmd' set but not used [-Wunused-but-set-variable] drivers/scsi/qedf/qedf_els.c:148:28: warning: variable 'task_ctx' set but not used [-Wunused-but-set-variable] drivers/scsi/qedf/qedf_els.c: In function 'qedf_send_srr': drivers/scsi/qedf/qedf_els.c:612:6: warning: variable 'sid' set but not used [-Wunused-but-set-variable] They are never used since introduction. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Update the driver version to 8.37.25.20Saurav Kashyap1-2/+2
Update the driver version to 8.37.25.20. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Add return value to log message if scsi_add_host failsSaurav Kashyap1-2/+3
Print return value of scsi_add_host on failure. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Print fcport information on wait for upload timeoutSaurav Kashyap1-3/+5
Log fcport for which upload failed. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Check the return value of start_xmitSaurav Kashyap2-3/+21
Log the reason for start xmit failure. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Log message if scsi_add_host failsSaurav Kashyap1-1/+4
Print message on scsi_add_host failure. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Check for fcoe_libfc_config failureSaurav Kashyap1-1/+5
Print the fcoe_libfc_config failure and return proper failure. Signed-off-by: Saurav Kashyap <saurav.kashyap@cavium.com> Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Add comment to display logging levelsSaurav Kashyap1-0/+6
Comment will help in decoding the logging level. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Add port_id for fcport into initiate_cleanup debug messageChad Dupuis1-2/+2
Port ID will help in debugging. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Add LBA to underrun debug messagesChad Dupuis1-5/+6
Print LBA information for underrun cases. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Print scsi_cmd backpointer in good completion path if the ↵Chad Dupuis1-3/+3
command is still being used Printing scsi command pointer will help in crash dump analysis. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Add driver state to 'driver_stats' debugfs nodeChad Dupuis1-3/+52
Add debugfs node for driver stats. [mkp: typo] Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-29scsi: qedf: Change MSI-X load error messageChad Dupuis1-1/+2
Change the message to display load failure. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-18scsi: qedf: remove memset/memcpy to nfunc and use func insteadColin Ian King1-24/+8
Currently the qedf_dbg_* family of functions can overrun the end of the source string if it is less than the destination buffer length because of the use of a fixed sized memcpy. Remove the memset/memcpy calls to nfunc and just use func instead as it is always a null terminated string. Addresses-Coverity: ("Out-of-bounds access") Fixes: 61d8658b4a43 ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-04-03scsi: qedf: Remove set but not used variable 'fr_len'YueHaibing1-2/+0
Fixes gcc '-Wunused-but-set-variable' warning: drivers/scsi/qedf/qedf_fip.c: In function 'qedf_fcoe_send_vlan_req': drivers/scsi/qedf/qedf_fip.c:22:6: warning: variable 'fr_len' set but not used [-Wunused-but-set-variable] It's never used since introduction and can be removed. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Update the driver version to 8.37.25.19Saurav Kashyap1-4/+4
- Update the driver version. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Fix lport may be used uninitialized warningSaurav Kashyap1-3/+1
- lport was getting used without initialization, initialize it to fix a warning. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Correctly handle refcounting of rdataSaurav Kashyap1-15/+11
- Handle refcount of rdata during error conditions. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Cleanup rrq_work after QEDF_CMD_OUTSTANDING is clearedShyam Sundar2-16/+54
Here is the relevant logs for the problem we are solving: qedf_flush_active_ios:1707]:3: Flush active i/o's num=0x17 fcport=0xffff948168fbcc80 port_id=0x550200 scsi_id=0. qedf_flush_active_ios:1708]:3: Locking flush mutex. qedf_flush_active_ios:1758]:3: Not outstanding, xid=0xaaf, cmd_type=3 refcount=1. qedf_flush_active_ios:1896]:3: Flushed 0x16 I/Os, active=0x1. qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x1 cnt=60. qedf_send_rrq:295]:3: Sending RRQ orig io = ffffb48b8f7d7158, orig_xid = 0xaaf qedf_initiate_els:37]:3: Sending ELS qedf_initiate_els:68]:3: initiate_els els_req = 0xffffb48b8f6d3098 cb_arg = ffff948fd5e4de80 xid = 4c6 qedf_init_mp_req:2172]:3: Entered. qedf_init_mp_task:727]:3: Initializing MP task for cmd_type=4 qedf_initiate_els:134]:3: Ringing doorbell for ELS req qedf_flush_active_ios:1901]:3: Flushed 0x16 I/Os, active=0x2 cnt=20. qedf_cmd_timeout:96]:3: ELS timeout, xid=0x4c6. qedf_rrq_compl:186]:3: Entered. qedf_rrq_compl:204]:3: rrq_compl: orig io = ffffb48b8f7d7158, orig xid = 0xaaf, rrq_xid = 0x4c6, refcount=1 qedf_flush_active_ios:1935]:3: Unlocking flush mutex. qedf_upload_connection:1579]:3: Uploading connection port_id=550200. We found an ABTS command for which CMD_OUTSTANDING was cleared (line 3). For this command, delayed send_rrq was queued, but would take 10 secs to execute. Adding capability to detect that (based on io_req->state that is being introduced), and attempt to cancel rrq_work. If we succeed, we drop the reference and free the io_req. If we cannot, then the els will get sent out and we will wait for 10 secs for it to complete. Signed-off-by: Shyam Sundar <ssundar@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Check for tm_flags instead of cmd_type during cleanupSaurav Kashyap1-1/+2
cmd_type is over written to QEDF_CLEANUP during cleanup, so check for tm_flags. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Add a flag to help debugging io_req which could not be cleanedShyam Sundar1-0/+7
- The flag will help in to figure out if io_req is cleaned or not. Signed-off-by: Shyam Sundar <ssundar@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Don't send ABTS for under run scenarioSaurav Kashyap1-9/+1
- Command is already completed with underrun so no need to send ABTS. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Don't queue anything if upload is in progressShyam Sundar1-1/+8
- I/Os, aborts and tmf should not be queued if flush is in progress. Signed-off-by: Shyam Sundar <ssundar@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Check both the FCF and fabric ID before servicing clear virtual linkChad Dupuis1-18/+48
- Check proper values before servicing CVL. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: fc_rport_priv reference counting fixesHannes Reinecke3-9/+30
The fc_rport_priv structure is reference counted, so we need to ensure that the reference is increased before accessing the structure. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Add missing return in qedf_scsi_done()Chad Dupuis1-0/+1
On completions where we do not have a bad scsi_cmnd pointer we should return before the the label lest we do a double kref_put. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Wait for upload and link down processing during soft ctx resetChad Dupuis3-11/+57
- Wait for all the connections to get uploaded. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Add additional checks for io_req->sc_cmd validityChad Dupuis1-2/+37
- Check the validity of various pointers before processing. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: fixup bit operationsHannes Reinecke2-1/+8
test_bit() is atomic, test_bit() || test_bit() is not. So protect consecutive bit tests with a lock to avoid races. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: fixup locking in qedf_restart_rport()Hannes Reinecke1-1/+7
fc_rport_create() needs to be called with disc_mutex held. And we should re-assign the 'rdata' pointer in case it got changed. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: missing kref_put in qedf_xmit()Hannes Reinecke1-1/+3
qedf_xmit() calls fc_rport_lookup(), but discards the returned rdata structure almost immediately without decreasing the refcount. This leads to a refcount leak and the rdata never to be freed. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Check for link state before processing LL2 packets and send ↵Saurav Kashyap2-6/+28
fipvlan retries - Check if link is UP before sending and processing any packets on wire. Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Add missing fc_disc_init call after allocating lportChad Dupuis1-0/+2
When receiving an unsolicited frame we could crash on a list traversal in fc_rport_lookup while searching the rport which is associated with our lport. Initialize the lport's discovery node after allocating the lport in __qedf_probe(). Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Correct the memory barriers in qedf_ring_doorbellAndrew Vasquez1-2/+10
- Correct memory barriers to make sure all cmnds are flushed. Signed-off-by: Andrew Vasquez <andrewv@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: qedf: Use a separate completion for cleanup commandsChad Dupuis2-4/+8
- If a TMF and cleanup are issued at the same time they could cause a call trace if issued against the same xid as the io_req->tm_done completion is used for both. - Set and clear cleanup bit in cleanup routine. Signed-off-by: Chad Dupuis <cdupuis@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-04 22:48:28 +0000