| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit
799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com
Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp")
Cc: <stable@vger.kernel.org> #2.6.32+
Suggested-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull dax and libnvdimm updates from Dan Williams:
"The bulk of this is a rework of the dax_operations API after
discovering the obstacles it posed to the work-in-progress DAX+reflink
support for XFS and other copy-on-write filesystem mechanics.
Primarily the need to plumb a block_device through the API to handle
partition offsets was a sticking point and Christoph untangled that
dependency in addition to other cleanups to make landing the
DAX+reflink support easier.
The DAX_PMEM_COMPAT option has been around for 4 years and not only
are distributions shipping userspace that understand the current
configuration API, but some are not even bothering to turn this option
on anymore, so it seems a good time to remove it per the deprecation
schedule. Recall that this was added after the device-dax subsystem
moved from /sys/class/dax to /sys/bus/dax for its sysfs organization.
All recent functionality depends on /sys/bus/dax.
Some other miscellaneous cleanups and reflink prep patches are
included as well.
Summary:
- Simplify the dax_operations API:
- Eliminate bdev_dax_pgoff() in favor of the filesystem
maintaining and applying a partition offset to all its DAX iomap
operations.
- Remove wrappers and device-mapper stacked callbacks for
->copy_from_iter() and ->copy_to_iter() in favor of moving
block_device relative offset responsibility to the
dax_direct_access() caller.
- Remove the need for an @bdev in filesystem-DAX infrastructure
- Remove unused uio helpers copy_from_iter_flushcache() and
copy_mc_to_iter() as only the non-check_copy_size() versions are
used for DAX.
- Prepare XFS for the pending (next merge window) DAX+reflink support
- Remove deprecated DEV_DAX_PMEM_COMPAT support
- Cleanup a straggling misuse of the GUID api"
* tag 'libnvdimm-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (38 commits)
iomap: Fix error handling in iomap_zero_iter()
ACPI: NFIT: Import GUID before use
dax: remove the copy_from_iter and copy_to_iter methods
dax: remove the DAXDEV_F_SYNC flag
dax: simplify dax_synchronous and set_dax_synchronous
uio: remove copy_from_iter_flushcache() and copy_mc_to_iter()
iomap: turn the byte variable in iomap_zero_iter into a ssize_t
memremap: remove support for external pgmap refcounts
fsdax: don't require CONFIG_BLOCK
iomap: build the block based code conditionally
dax: fix up some of the block device related ifdefs
fsdax: shift partition offset handling into the file systems
dax: return the partition offset from fs_dax_get_by_bdev
iomap: add a IOMAP_DAX flag
xfs: pass the mapping flags to xfs_bmbt_to_iomap
xfs: use xfs_direct_write_iomap_ops for DAX zeroing
xfs: move dax device handling into xfs_{alloc,free}_buftarg
ext4: cleanup the dax handling in ext4_fill_super
ext2: cleanup the dax handling in ext2_fill_super
fsdax: decouple zeroing from the iomap buffered I/O code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver cleanups.
This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: core: Keep mctrl register state and cached copy in sync
serial: stm32: correct loop for dma error handling
serial: stm32: fix flow control transfer in DMA mode
serial: stm32: rework TX DMA state condition
serial: stm32: move tx dma terminate DMA to shutdown
serial: pl011: Drop redundant DTR/RTS preservation on close/open
serial: pl011: Drop CR register reset on set_termios
serial: pl010: Drop CR register reset on set_termios
serial: liteuart: fix MODULE_ALIAS
serial: 8250_bcm7271: Fix return error code in case of dma_alloc_coherent() failure
Revert "serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2"
tty: goldfish: Use platform_get_irq() to get the interrupt
serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2
tty: serial: meson: Drop the legacy compatible strings and clock code
serial: pmac_zilog: Use platform_get_irq() to get the interrupt
serial: bcm63xx: Use platform_get_irq() to get the interrupt
serial: ar933x: Use platform_get_irq() to get the interrupt
serial: vt8500: Use platform_get_irq() to get the interrupt
serial: altera_jtaguart: Use platform_get_irq_optional() to get the interrupt
serial: pxa: Use platform_get_irq() to get the interrupt
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core
----
- Defer freeing TCP skbs to the BH handler, whenever possible, or at
least perform the freeing outside of the socket lock section to
decrease cross-CPU allocator work and improve latency.
- Add netdevice refcount tracking to locate sources of netdevice and
net namespace refcount leaks.
- Make Tx watchdog less intrusive - avoid pausing Tx and restarting
all queues from a single CPU removing latency spikes.
- Various small optimizations throughout the stack from Eric Dumazet.
- Make netdev->dev_addr[] constant, force modifications to go via
appropriate helpers to allow us to keep addresses in ordered data
structures.
- Replace unix_table_lock with per-hash locks, improving performance
of bind() calls.
- Extend skb drop tracepoint with a drop reason.
- Allow SO_MARK and SO_PRIORITY setsockopt under CAP_NET_RAW.
BPF
---
- New helpers:
- bpf_find_vma(), find and inspect VMAs for profiling use cases
- bpf_loop(), runtime-bounded loop helper trading some execution
time for much faster (if at all converging) verification
- bpf_strncmp(), improve performance, avoid compiler flakiness
- bpf_get_func_arg(), bpf_get_func_ret(), bpf_get_func_arg_cnt()
for tracing programs, all inlined by the verifier
- Support BPF relocations (CO-RE) in the kernel loader.
- Further the support for BTF_TYPE_TAG annotations.
- Allow access to local storage in sleepable helpers.
- Convert verifier argument types to a composable form with different
attributes which can be shared across types (ro, maybe-null).
- Prepare libbpf for upcoming v1.0 release by cleaning up APIs,
creating new, extensible ones where missing and deprecating those
to be removed.
Protocols
---------
- WiFi (mac80211/cfg80211):
- notify user space about long "come back in N" AP responses,
allow it to react to such temporary rejections
- allow non-standard VHT MCS 10/11 rates
- use coarse time in airtime fairness code to save CPU cycles
- Bluetooth:
- rework of HCI command execution serialization to use a common
queue and work struct, and improve handling errors reported in
the middle of a batch of commands
- rework HCI event handling to use skb_pull_data, avoiding packet
parsing pitfalls
- support AOSP Bluetooth Quality Report
- SMC:
- support net namespaces, following the RDMA model
- improve connection establishment latency by pre-clearing buffers
- introduce TCP ULP for automatic redirection to SMC
- Multi-Path TCP:
- support ioctls: SIOCINQ, OUTQ, and OUTQNSD
- support socket options: IP_TOS, IP_FREEBIND, IP_TRANSPARENT,
IPV6_FREEBIND, and IPV6_TRANSPARENT, TCP_CORK and TCP_NODELAY
- support cmsgs: TCP_INQ
- improvements in the data scheduler (assigning data to subflows)
- support fastclose option (quick shutdown of the full MPTCP
connection, similar to TCP RST in regular TCP)
- MCTP (Management Component Transport) over serial, as defined by
DMTF spec DSP0253 - "MCTP Serial Transport Binding".
Driver API
----------
- Support timestamping on bond interfaces in active/passive mode.
- Introduce generic phylink link mode validation for drivers which
don't have any quirks and where MAC capability bits fully express
what's supported. Allow PCS layer to participate in the validation.
Convert a number of drivers.
- Add support to set/get size of buffers on the Rx rings and size of
the tx copybreak buffer via ethtool.
- Support offloading TC actions as first-class citizens rather than
only as attributes of filters, improve sharing and device resource
utilization.
- WiFi (mac80211/cfg80211):
- support forwarding offload (ndo_fill_forward_path)
- support for background radar detection hardware
- SA Query Procedures offload on the AP side
New hardware / drivers
----------------------
- tsnep - FPGA based TSN endpoint Ethernet MAC used in PLCs with
real-time requirements for isochronous communication with protocols
like OPC UA Pub/Sub.
- Qualcomm BAM-DMUX WWAN - driver for data channels of modems
integrated into many older Qualcomm SoCs, e.g. MSM8916 or MSM8974
(qcom_bam_dmux).
- Microchip LAN966x multi-port Gigabit AVB/TSN Ethernet Switch driver
with support for bridging, VLANs and multicast forwarding
(lan966x).
- iwlmei driver for co-operating between Intel's WiFi driver and
Intel's Active Management Technology (AMT) devices.
- mse102x - Vertexcom MSE102x Homeplug GreenPHY chips
- Bluetooth:
- MediaTek MT7921 SDIO devices
- Foxconn MT7922A
- Realtek RTL8852AE
Drivers
-------
- Significantly improve performance in the datapaths of: lan78xx,
ax88179_178a, lantiq_xrx200, bnxt.
- Intel Ethernet NICs:
- igb: support PTP/time PEROUT and EXTTS SDP functions on
82580/i354/i350 adapters
- ixgbevf: new PF -> VF mailbox API which avoids the risk of
mailbox corruption with ESXi
- iavf: support configuration of VLAN features of finer
granularity, stacked tags and filtering
- ice: PTP support for new E822 devices with sub-ns precision
- ice: support firmware activation without reboot
- Mellanox Ethernet NICs (mlx5):
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- support TC forwarding when tunnel encap and decap happen between
two ports of the same NIC
- dynamically size and allow disabling various features to save
resources for running in embedded / SmartNIC scenarios
- Broadcom Ethernet NICs (bnxt):
- use page frag allocator to improve Rx performance
- expose control over IRQ coalescing mode (CQE vs EQE) via ethtool
- Other Ethernet NICs:
- amd-xgbe: add Ryzen 6000 (Yellow Carp) Ethernet support
- Microsoft cloud/virtual NIC (mana):
- add XDP support (PASS, DROP, TX)
- Mellanox Ethernet switches (mlxsw):
- initial support for Spectrum-4 ASICs
- VxLAN with IPv6 underlay
- Marvell Ethernet switches (prestera):
- support flower flow templates
- add basic IP forwarding support
- NXP embedded Ethernet switches (ocelot & felix):
- support Per-Stream Filtering and Policing (PSFP)
- enable cut-through forwarding between ports by default
- support FDMA to improve packet Rx/Tx to CPU
- Other embedded switches:
- hellcreek: improve trapping management (STP and PTP) packets
- qca8k: support link aggregation and port mirroring
- Qualcomm 802.11ax WiFi (ath11k):
- qca6390, wcn6855: enable 802.11 power save mode in station mode
- BSS color change support
- WCN6855 hw2.1 support
- 11d scan offload support
- scan MAC address randomization support
- full monitor mode, only supported on QCN9074
- qca6390/wcn6855: report signal and tx bitrate
- qca6390: rfkill support
- qca6390/wcn6855: regdb.bin support
- Intel WiFi (iwlwifi):
- support SAR GEO Offset Mapping (SGOM) and Time-Aware-SAR (TAS)
in cooperation with the BIOS
- support for Optimized Connectivity Experience (OCE) scan
- support firmware API version 68
- lots of preparatory work for the upcoming Bz device family
- MediaTek WiFi (mt76):
- Specific Absorption Rate (SAR) support
- mt7921: 160 MHz channel support
- RealTek WiFi (rtw88):
- Specific Absorption Rate (SAR) support
- scan offload
- Other WiFi NICs
- ath10k: support fetching (pre-)calibration data from nvmem
- brcmfmac: configure keep-alive packet on suspend
- wcn36xx: beacon filter support"
* tag '5.17-net-next' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2048 commits)
tcp: tcp_send_challenge_ack delete useless param `skb`
net/qla3xxx: Remove useless DMA-32 fallback configuration
rocker: Remove useless DMA-32 fallback configuration
hinic: Remove useless DMA-32 fallback configuration
lan743x: Remove useless DMA-32 fallback configuration
net: enetc: Remove useless DMA-32 fallback configuration
cxgb4vf: Remove useless DMA-32 fallback configuration
cxgb4: Remove useless DMA-32 fallback configuration
cxgb3: Remove useless DMA-32 fallback configuration
bnx2x: Remove useless DMA-32 fallback configuration
et131x: Remove useless DMA-32 fallback configuration
be2net: Remove useless DMA-32 fallback configuration
vmxnet3: Remove useless DMA-32 fallback configuration
bna: Simplify DMA setting
net: alteon: Simplify DMA setting
myri10ge: Simplify DMA setting
qlcnic: Simplify DMA setting
net: allwinner: Fix print format
page_pool: remove spinlock in page_pool_refill_alloc_cache()
amt: fix wrong return type of amt_send_membership_update()
...
|
|
There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field. Move the s390 dasd sysfs code to use default_groups field
which has been the preferred way since commit aa30f47cf666 ("kobject:
Add support for default attribute groups to kobj_type") so that we can
soon get rid of the obsolete default_attrs field.
Cc: Stefan Haberland <sth@linux.ibm.com>
Cc: Jan Hoeppner <hoeppner@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220106095401.3274637-1-gregkh@linuxfoundation.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field. Move the sclp_sd sysfs code to use default_groups field which
has been the preferred way since commit aa30f47cf666 ("kobject: Add
support for default attribute groups to kobj_type") so that we can
soon get rid of the obsolete default_attrs field.
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220106095252.3273905-1-gregkh@linuxfoundation.org
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
These methods indirect the actual DAX read/write path. In the end pmem
uses magic flush and mc safe variants and fuse and dcssblk use plain ones
while device mapper picks redirects to the underlying device.
Add set_dax_nocache() and set_dax_nomc() APIs to control which copy
routines are used to remove indirect call from the read/write fast path
as well as a lot of boilerplate code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Vivek Goyal <vgoyal@redhat.com> [virtiofs]
Link: https://lore.kernel.org/r/20211215084508.435401-5-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Remove the DAXDEV_F_SYNC flag and thus the flags argument to alloc_dax and
just let the drivers call set_dax_synchronous directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20211215084508.435401-4-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When sending a CCA CPRB to a control domain, the CPRB has to be sent via a
usage domain. Previous code used the default domain to route this message.
If the default domain is not online and ready to send the CPRB, the ioctl will
fail even if other usage domains could be used to send the CPRB.
To improve this, instead of using the default domain, switch to auto-select of
the domain.
Signed-off-by: Juergen Christ <jchrist@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
memblock_phys_free() is used on a virtual address. Fix this by using
memblock_free().
Note: this doesn't fix a bug currently, since virtual and physical
addresses are identical.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
If qeth_check_outbound_queue() finds a partially filled TX buffer on
the queue and flushes it, then the queue _must_ have been in packing
mode.
Remove the redundant check when updating the relevant statistics.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid a conditional branch for L2 devices when selecting the TX queue,
and have shared logic for OSA devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
qeth_l2_detect_dev2br_support() will only set brport_hw_features for IQD
devices. So qeth_l2_bridge_getlink() and qeth_l2_bridge_setlink() will
always return -EOPNOTSUPP on OSA devices. Just don't offer these
callbacks instead.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Splitting up the netdev_ops allows for fine-tuning some of the ndo's
in subsequent patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the OSN code is gone, we don't need the second switch statement
in the RX path. And getting rid of its (unreachable) default case is a
nice simplification.
Also don't pass in the full HW header, all we still need is a flag to
indicate whether the skb can use CSO. This we can already obtain during
the first peek at the HW header.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds a sysfs 'status' attribute to a queue device when it is
bound to the vfio_ap device driver. The field displays a string indicating
the status of the queue device:
Status String: Indicates:
------------- ---------
"assigned" the queue is assigned to an mdev, but is not in use by a
KVM guest.
"in use" the queue is assigned to an mdev and is in use by a KVM
guest.
"unassigned" the queue is not assigned to an mdev.
The status string will be displayed by the 'lszcrypt' command if the queue
device is bound to the vfio_ap device driver.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
[akrowiak@linux.ibm.com: added check for queue in use by guest]
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
All callers of set_buf_states() are already making sure that 'count'
is not 0. So don't check it an additional time.
Note that our own code also doesn't _require_ the count to be sane
(ie. we can't overrun an array or similar). So worst case HW would
simply reject the SQBS operation and report an error.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Fix wrong usage of page_to_phys/phys_to_page.
Note: this currently doesn't fix a real bug, since virtual addresses
are indentical to physical ones.
Acked-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The callers know what type of queue they want to work with. Introduce
type-specific variants to add buffers on an {Input,Output} queue, so
that we can avoid some function parameters and the de-muxing into
type-specific hot paths.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The callers know what type of queue they want to inspect. Introduce
type-specific variants to inspect an {Input,Output} queue, so that we
can avoid one function parameter and some conditional branches in the
hot paths.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
qdio_handle_activate_check() tries to re-use one of the queue-specific
handlers to report that the ACTIVATE ccw has been terminated. But the
logic to select that handler is overly complex - in practice both
qdio drivers have at least one Input Queue, so we never take the other
paths.
Make things more obvious by removing this unused code, and clearly
spelling out that we re-use the Input Handler for generic error
reporting. This also paves the way for a world without queue-specific
error handlers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
qdio_handle_activate_check() re-uses a queue-specific handler to report
that the ACTIVATE ccw has been terminated. It uses either the first
input or output queue, so we can hard-code q->nr as 0. Also don't
access the q->irq_ptr parent pointer, we already have a pointer to
the qdio_irq.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The qdio_irq contains only two fields that are directly exposed to the
HW (ccw and qib). And only the ccw needs to reside in 31-bit memory. So
allocate it separately, and remove the GFP_DMA constraint from the
qdio_irq allocation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Fetch the individual CIWs when we actually need them, rather than
fetching both of them in qdio_setup_irq() and then needing to cache
them inside the qdio_irq.
Also deal with the error when a CIW is not available, instead of
silently dropping this error condition in qdio_setup_irq()'s caller.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
commit fa1a8c23eb7d ("s390: cio: Delay uevents for subchannels")
introduced suppression of uevents for a subchannel until after it is
clear that the subchannel would not be unregistered again
immediately. This was done to avoid uevents being generated for I/O
subchannels with no valid device, which can happen on LPAR.
However, this also has some drawbacks: All subchannel drivers need to
manually remove the uevent suppression and generate an ADD uevent as
soon as they are sure that the subchannel will stay around. This misses
out on all uevents that are not the initial ADD uevent that would be
generated while uevents are suppressed; for example, all subchannels
were missing the BIND uevent.
As uevents being generated even for I/O subchannels without an
operational device turned out to be not as bad as missing uevents and
complicating the code flow, let's remove uevent suppression for
subchannels.
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
[cohuck@redhat.com: modified changelog]
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Link: https://lore.kernel.org/r/20211122103756.352463-2-vneethv@linux.ibm.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Just open code the block size and dax_dev == NULL checks in the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com> [erofs]
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20211129102203.2243509-9-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Replace the dax_host_hash with an xarray indexed by the pointer value
of the gendisk, and require explicitly calls from the block drivers that
want to associate their gendisk with a dax_device.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20211129102203.2243509-5-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
CONFIG_DAX_DRIVER only selects CONFIG_DAX now, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/20211129102203.2243509-4-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
drivers/net/ipa/ipa_main.c
8afc7e471ad3 ("net: ipa: separate disabling setup from modem stop")
76b5fbcd6b47 ("net: ipa: kill ipa_modem_init()")
Duplicated include, drop one.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit a9c3f68f3cd8d (tty: Fix low_latency BUG) in 2014,
tty_flip_buffer_push() is only a wrapper to tty_schedule_flip(). We are
going to remove the latter (as it is used less), so call the former in
the rest of the users.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211122111648.30379-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix allmodconfig + W=1 compile breakage:
drivers/s390/net/lcs.c: In function ‘lcs_get_frames_cb’:
drivers/s390/net/lcs.c:1823:25: error: suggest braces around empty body in an ‘else’ statement [-Werror=empty-body]
1823 | ; // FIXME: error message ?
| ^
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the compiler to recognize and check format strings and parameters.
As reported with allmodconfig and W=1:
drivers/s390/net/ctcm_dbug.c: In function ‘ctcm_dbf_longtext’:
drivers/s390/net/ctcm_dbug.c:73:9: error: function ‘ctcm_dbf_longtext’ might be a candidate for ‘gnu_printf’ format attribute [-Werror=suggest-attribute=format]
73 | vsnprintf(dbf_txt_buf, sizeof(dbf_txt_buf), fmt, args);
| ^~~~~~~~~
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The second parameter as specified by the format string is actually a
string not an integer.
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We always need an RX queue, and there's no reconfig situation either
where we would need to free & rebuild the queue.
So allocate the RX queue right from the start, and avoid freeing it
during unrelated qeth_free_qdio_queues() calls.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
show() must not use snprintf() when formatting the value to be
returned to user space.
Fix the coccicheck warnings:
WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Acked-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Acked-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/1634280655-4908-1-git-send-email-wangqing@vivo.com
[hca@linux.ibm.com: fix indentation]
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Check the validity of subchanel before reading other fields in
the schib.
Fixes: d3683c055212 ("s390/cio: add dev_busid sysfs entry for each subchannel")
CC: <stable@vger.kernel.org>
Reported-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Link: https://lore.kernel.org/r/20211105154451.847288-1-vneethv@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
commit 9c6c273aa424 ("timer: Remove init_timer_on_stack() in favor
of timer_setup_on_stack()") changed the timer setup from
init_timer_on_stack(() to timer_setup(), but missed to change the
mod_timer() call. And while at it, use msecs_to_jiffies() instead
of the open coded timeout calculation.
Cc: stable@vger.kernel.org
Fixes: 9c6c273aa424 ("timer: Remove init_timer_on_stack() in favor of timer_setup_on_stack()")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for ftrace with direct call and ftrace direct call
samples.
- Add support for kernel command lines longer than current 896 bytes
and make its length configurable.
- Add support for BEAR enhancement facility to improve last breaking
event instruction tracking.
- Add kprobes sanity checks and testcases to prevent kprobe in the mid
of an instruction.
- Allow concurrent access to /dev/hwc for the CPUMF users.
- Various ftrace / jump label improvements.
- Convert unwinder tests to KUnit.
- Add s390_iommu_aperture kernel parameter to tweak the limits on
concurrently usable DMA mappings.
- Add ap.useirq AP module option which can be used to disable interrupt
use.
- Add add_disk() error handling support to block device drivers.
- Drop arch specific and use generic implementation of strlcpy and
strrchr.
- Several __pa/__va usages fixes.
- Various cio, crypto, pci, kernel doc and other small fixes and
improvements all over the code.
[ Merge fixup as per https://lore.kernel.org/all/YXAqZ%2FEszRisunQw@osiris/ ]
* tag 's390-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (63 commits)
s390: make command line configurable
s390: support command lines longer than 896 bytes
s390/kexec_file: move kernel image size check
s390/pci: add s390_iommu_aperture kernel parameter
s390/spinlock: remove incorrect kernel doc indicator
s390/string: use generic strlcpy
s390/string: use generic strrchr
s390/ap: function rework based on compiler warning
s390/cio: make ccw_device_dma_* more robust
s390/vfio-ap: s390/crypto: fix all kernel-doc warnings
s390/hmcdrv: fix kernel doc comments
s390/ap: new module option ap.useirq
s390/cpumf: Allow multiple processes to access /dev/hwc
s390/bitops: return true/false (not 1/0) from bool functions
s390: add support for BEAR enhancement facility
s390: introduce nospec_uses_trampoline()
s390: rename last_break to pgm_last_break
s390/ptrace: add last_break member to pt_regs
s390/sclp: sort out physical vs virtual pointers usage
s390/setup: convert start and end initrd pointers to virtual
...
|
|
Merge misc updates from Andrew Morton:
"257 patches.
Subsystems affected by this patch series: scripts, ocfs2, vfs, and
mm (slab-generic, slab, slub, kconfig, dax, kasan, debug, pagecache,
gup, swap, memcg, pagemap, mprotect, mremap, iomap, tracing, vmalloc,
pagealloc, memory-failure, hugetlb, userfaultfd, vmscan, tools,
memblock, oom-kill, hugetlbfs, migration, thp, readahead, nommu, ksm,
vmstat, madvise, memory-hotplug, rmap, zsmalloc, highmem, zram,
cleanups, kfence, and damon)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (257 commits)
mm/damon: remove return value from before_terminate callback
mm/damon: fix a few spelling mistakes in comments and a pr_debug message
mm/damon: simplify stop mechanism
Docs/admin-guide/mm/pagemap: wordsmith page flags descriptions
Docs/admin-guide/mm/damon/start: simplify the content
Docs/admin-guide/mm/damon/start: fix a wrong link
Docs/admin-guide/mm/damon/start: fix wrong example commands
mm/damon/dbgfs: add adaptive_targets list check before enable monitor_on
mm/damon: remove unnecessary variable initialization
Documentation/admin-guide/mm/damon: add a document for DAMON_RECLAIM
mm/damon: introduce DAMON-based Reclamation (DAMON_RECLAIM)
selftests/damon: support watermarks
mm/damon/dbgfs: support watermarks
mm/damon/schemes: activate schemes based on a watermarks mechanism
tools/selftests/damon: update for regions prioritization of schemes
mm/damon/dbgfs: support prioritization weights
mm/damon/vaddr,paddr: support pageout prioritization
mm/damon/schemes: prioritize regions within the quotas
mm/damon/selftests: support schemes quotas
mm/damon/dbgfs: support quotas of schemes
...
|
|
Since memblock_free() operates on a physical range, make its name
reflect it and rename it to memblock_phys_free(), so it will be a
logical counterpart to memblock_phys_alloc().
The callers are updated with the below semantic patch:
@@
expression addr;
expression size;
@@
- memblock_free(addr, size);
+ memblock_phys_free(addr, size);
Link: https://lkml.kernel.org/r/20210930185031.18648-6-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Juergen Gross <jgross@suse.com>
Cc: Shahab Vahedi <Shahab.Vahedi@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
memblock_free_early_nid() is unused and memblock_free_early() is an
alias for memblock_free().
Replace calls to memblock_free_early() with calls to memblock_free() and
remove memblock_free_early() and memblock_free_early_nid().
Link: https://lkml.kernel.org/r/20210930185031.18648-4-rppt@kernel.org
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Juergen Gross <jgross@suse.com>
Cc: Shahab Vahedi <Shahab.Vahedi@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes.
Notable core changes are the removal of scsi->tag which caused some
churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: lpfc: Update lpfc version to 14.0.0.3
scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
scsi: lpfc: Fix link down processing to address NULL pointer dereference
scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
scsi: ufs: mediatek: Avoid sched_clock() misuse
scsi: mpt3sas: Make mpt3sas_dev_attrs static
scsi: scsi_transport_sas: Add 22.5 Gbps link rate definitions
scsi: target: core: Stop using bdevname()
scsi: aha1542: Use memcpy_{from,to}_bvec()
scsi: sr: Add error handling support for add_disk()
scsi: sd: Add error handling support for add_disk()
scsi: target: Perform ALUA group changes in one step
scsi: target: Replace lun_tg_pt_gp_lock with rcu in I/O path
scsi: target: Fix alua_tg_pt_gps_count tracking
scsi: target: Fix ordered tag handling
...
|
|
Pull VFIO updates from Alex Williamson:
- Cleanup vfio iommu_group creation (Christoph Hellwig)
- Add individual device reset for vfio/fsl-mc (Diana Craciun)
- IGD OpRegion 2.0+ support (Colin Xu)
- Use modern cdev lifecycle for vfio_group (Jason Gunthorpe)
- Use new mdev API in vfio_ccw (Jason Gunthorpe)
* tag 'vfio-v5.16-rc1' of git://github.com/awilliam/linux-vfio: (27 commits)
vfio/ccw: Convert to use vfio_register_emulated_iommu_dev()
vfio/ccw: Pass vfio_ccw_private not mdev_device to various functions
vfio/ccw: Use functions for alloc/free of the vfio_ccw_private
vfio/ccw: Remove unneeded GFP_DMA
vfio: Use cdev_device_add() instead of device_create()
vfio: Use a refcount_t instead of a kref in the vfio_group
vfio: Don't leak a group reference if the group already exists
vfio: Do not open code the group list search in vfio_create_group()
vfio: Delete vfio_get/put_group from vfio_iommu_group_notifier()
vfio/pci: Add OpRegion 2.0+ Extended VBT support.
vfio/iommu_type1: remove IS_IOMMU_CAP_DOMAIN_IN_CONTAINER
vfio/iommu_type1: remove the "external" domain
vfio/iommu_type1: initialize pgsize_bitmap in ->open
vfio/spapr_tce: reject mediated devices
vfio: clean up the check for mediated device in vfio_iommu_type1
vfio: remove the unused mdev iommu hook
vfio: move the vfio_iommu_driver_ops interface out of <linux/vfio.h>
vfio: remove unused method from vfio_iommu_driver_ops
vfio: simplify iommu group allocation for mediated devices
vfio: remove the iommudata hack for noiommu groups
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
|
|
This is a more complicated conversion because vfio_ccw is sharing the
vfio_device between both the mdev_device, its vfio_device and the
css_driver.
The mdev is a singleton, and the reason for this sharing is so the extra
css_driver function callbacks to be delivered to the vfio_device
implementation.
This keeps things as they are, with the css_driver allocating the
singleton, not the mdev_driver.
Embed the vfio_device in the vfio_ccw_private and instantiate it as a
vfio_device when the mdev probes. The drvdata of both the css_device and
the mdev_device point at the private, and container_of is used to get it
back from the vfio_device.
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/4-v4-cea4f5bd2c00+b52-ccw_mdev_jgg@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
mdev_device should only be used in functions assigned to ops callbacks,
interior functions should use the struct vfio_ccw_private instead of
repeatedly trying to get it from the mdev.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/3-v4-cea4f5bd2c00+b52-ccw_mdev_jgg@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Makes the code easier to understand what is memory lifecycle and what is
other stuff.
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/2-v4-cea4f5bd2c00+b52-ccw_mdev_jgg@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Since the ccw_io_region was split out of the private the allocation no
longer needs the GFP_DMA. Remove it.
Reported-by: Christoph Hellwig <hch@infradead.org>
Fixes: c98e16b2fa12 ("s390/cio: Convert ccw_io_region to pointer")
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/1-v4-cea4f5bd2c00+b52-ccw_mdev_jgg@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Slight rework of function __ap_revise_reserved()
because of unused variable warning when build with W=1.
This patch introduces an additional debug feature warning
message when device_reprobe() returns with failure.
However, the return value of __ap_revise_reserved()
is still hard coded to 0 as this is a callback function
to be used together with bus_for_each_dev() and thus
the return value indicates to go on with the
bus_for_each_dev() loop and not apport on a failure
of something within this function.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
