summaryrefslogtreecommitdiff
path: root/drivers/rtc
AgeCommit message (Collapse)AuthorFilesLines
2013-03-22drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMRNicolas Ferre2-20/+31
On some revisions of AT91 SoCs, the RTC IMR register is not working. Instead of elaborating a workaround for that specific SoC or IP version, we simply use a software variable to store the Interrupt Mask Register and modify it for each enabling/disabling of an interrupt. The overhead of this is negligible anyway. The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5 sub-family of SoCs (good overview of the members here: http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible effect" is the RTC doesn't work. That sub-family is less than two years old and only has devicetree (DT) support and came online circa lk 3.7 . The dust is yet to settle on the DT stuff at least for AT91 SoCs (translation: lots of stuff is still broken, so much that it is hard to know where to start). The fix in the patch is pretty simple: just shadow the silicon IMR register with a variable in the driver. Some older SoCs (pre-DT) use the the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should not be impacted by the change. There shouldn't be a large volume of interrupts associated with a RTC. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Reported-by: Douglas Gilbert <dgilbert@interlog.com> Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Ludovic Desroches <ludovic.desroches@atmel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-03-22drivers/rtc/rtc-da9052.c: fix for rtc device registrationAshish Jangam1-5/+3
Add support for the virtual irq since now MFD only handles virtual irq Without this patch rtc device will fail in registration. (akpm: Ashish has a different version whcih will be needed for 3.8.x and earlier kernels) Signed-off-by: Ashish <ashish.jangam@kpitcummins.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-03-08rtc: rtc-mv: Add support for clk to avoid lockupsAndrew Lunn1-4/+24
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the driver clk_prepare_enable() this clock, otherwise there is a danger the SoC will lockup when accessing RTC registers with the clock disabled. Reported-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Simon Baatz <gmbnomis@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-03-01rtc: stmp3xxx: add wdt-accessor functionWolfram Sang1-0/+64
This RTC also includes a watchdog timer. Provide an accessor function for setting the watchdog timeout value which will be picked up by a watchdog driver. Also register the platform_device for the watchdog here to get the boot-time dependencies right. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
2013-02-24Merge tag 'mfd-3.9-1' of ↵Linus Torvalds3-0/+350
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6 Pull MFS updates from Samuel Ortiz: "This is the MFD pull request for the 3.9 merge window. No new drivers this time, but a bunch of fairly big cleanups: - Roger Quadros worked on a OMAP USBHS and TLL platform data consolidation, OMAP5 support and clock management code cleanup. - The first step of a major sync for the ab8500 driver from Lee Jones. In particular, the debugfs and the sysct interfaces got extended and improved. - Peter Ujfalusi sent a nice patchset for cleaning and fixing the twl-core driver, with a much needed module id lookup code improvement. - The regular wm5102 and arizona cleanups and fixes from Mark Brown. - Laxman Dewangan extended the palmas APIs in order to implement the palmas GPIO and rt drivers. - Laxman also added DT support for the tps65090 driver. - The Intel SCH and ICH drivers got a couple fixes from Aaron Sierra and Darren Hart. - Linus Walleij patchset for the ab8500 driver allowed ab8500 and ab9540 based devices to switch to the new abx500 pin-ctrl driver. - The max8925 now has device tree and irqdomain support thanks to Qing Xu. - The recently added rtsx driver got a few cleanups and fixes for a better card detection code path and now also supports the RTS5227 chipset, thanks to Wei Wang and Roger Tseng." * tag 'mfd-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (109 commits) mfd: lpc_ich: Use devres API to allocate private data mfd: lpc_ich: Add Device IDs for Intel Wellsburg PCH mfd: lpc_sch: Accomodate partial population of the MFD devices mfd: da9052-i2c: Staticize da9052_i2c_fix() mfd: syscon: Fix sparse warning mfd: twl-core: Fix kernel panic on boot mfd: rtsx: Fix issue that booting OS with SD card inserted mfd: ab8500: Fix compile error mfd: Add missing GENERIC_HARDIRQS dependecies Documentation: Add docs for max8925 dt mfd: max8925: Add dts mfd: max8925: Support dt for backlight mfd: max8925: Fix onkey driver irq base mfd: max8925: Fix mfd device register failure mfd: max8925: Add irqdomain for dt mfd: vexpress: Allow vexpress-sysreg to self-initialise mfd: rtsx: Support RTS5227 mfd: rtsx: Implement driving adjustment to device-dependent callbacks mfd: vexpress: Add pseudo-GPIO based LEDs mfd: ab8500: Rename ab8500 to abx500 for hwmon driver ...
2013-02-21Merge branch 'akpm' (incoming from Andrew)Linus Torvalds41-226/+2430
Merge misc patches from Andrew Morton: - Florian has vanished so I appear to have become fbdev maintainer again :( - Joel and Mark are distracted to welcome to the new OCFS2 maintainer - The backlight queue - Small core kernel changes - lib/ updates - The rtc queue - Various random bits * akpm: (164 commits) rtc: rtc-davinci: use devm_*() functions rtc: rtc-max8997: use devm_request_threaded_irq() rtc: rtc-max8907: use devm_request_threaded_irq() rtc: rtc-da9052: use devm_request_threaded_irq() rtc: rtc-wm831x: use devm_request_threaded_irq() rtc: rtc-tps80031: use devm_request_threaded_irq() rtc: rtc-lp8788: use devm_request_threaded_irq() rtc: rtc-coh901331: use devm_clk_get() rtc: rtc-vt8500: use devm_*() functions rtc: rtc-tps6586x: use devm_request_threaded_irq() rtc: rtc-imxdi: use devm_clk_get() rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug() rtc: rtc-pcf8583: use dev_warn() instead of printk() rtc: rtc-sun4v: use pr_warn() instead of printk() rtc: rtc-vr41xx: use dev_info() instead of printk() rtc: rtc-rs5c313: use pr_err() instead of printk() rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug() rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug() rtc: rtc-ds2404: use dev_err() instead of printk() rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk() ...
2013-02-21rtc: rtc-davinci: use devm_*() functionsJingoo Han1-18/+10
Use devm_*() functions to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-max8997: use devm_request_threaded_irq()Jingoo Han1-4/+3
Use devm_request_threaded_irq() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-max8907: use devm_request_threaded_irq()Jingoo Han1-3/+3
Use devm_request_threaded_irq() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-da9052: use devm_request_threaded_irq()Jingoo Han1-12/+6
Use devm_request_threaded_irq() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-wm831x: use devm_request_threaded_irq()Jingoo Han1-5/+4
Use devm_request_threaded_irq() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-tps80031: use devm_request_threaded_irq()Jingoo Han1-2/+2
Use devm_request_threaded_irq() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-lp8788: use devm_request_threaded_irq()Jingoo Han1-8/+2
Use devm_request_threaded_irq() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-coh901331: use devm_clk_get()Jingoo Han1-5/+2
Use devm_clk_get() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-vt8500: use devm_*() functionsJingoo Han1-18/+10
Use devm_*() functions to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-tps6586x: use devm_request_threaded_irq()Jingoo Han1-2/+2
Use devm_request_threaded_irq() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-imxdi: use devm_clk_get()Jingoo Han1-3/+1
Use devm_clk_get() to make cleanup paths more simple. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()Jingoo Han1-8/+4
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-pcf8583: use dev_warn() instead of printk()Jingoo Han1-2/+2
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-sun4v: use pr_warn() instead of printk()Jingoo Han1-4/+6
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-vr41xx: use dev_info() instead of printk()Jingoo Han1-1/+1
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-rs5c313: use pr_err() instead of printk()Jingoo Han1-2/+3
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()Jingoo Han1-9/+8
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()Jingoo Han1-6/+4
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-ds2404: use dev_err() instead of printk()Jingoo Han1-2/+2
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()Jingoo Han1-4/+6
Fix the checkpatch warnings as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... WARNING: please, no space before tabs Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: max77686: use dev_info() instead of printk()Jingoo Han1-2/+2
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: use dev_warn()/dev_dbg()/pr_err() instead of printk()Jingoo Han2-6/+9
Fix the checkpatch warning as below: WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ... Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-sa1100.c: move clock enable/disable to probe/removeChao Xie1-5/+6
The original sa1100_rtc_open/sa1100_rtc_release will be called when the /dev/rtc0 is opened or closed. In fact, these two functions will enable/disable the clock. Disabling clock will make rtc not work. So only enable/disable clock when probe/remove the device. Signed-off-by: Chao Xie <chao.xie@marvell.com> Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> Cc: Leo Song <liangs@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: max8997: add driver for max8997 rtcJonghwa Lee3-0/+564
Add an rtc driver for Maxim 8997 multifunction chip. Max8997 has rtc module in it. and it can be used for timekeeping clock and system alarm. It provide various operational mode those are BCD/binary, 24/12hour, am/pm. Driver sets binary/24/ for default. Maxim 8997 also supports SMPL(Sudden Momentary Power Loss), WTSR (Watchdog Timeout and Software Reset). Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com> Cc: Devendra Naga <devendra.aaru@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-s3c.c: use dev_dbg() instaed of pr_debug()Jingoo Han1-9/+9
Use dev_dbg() instaed of pr_debug() to be consistent. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-pl031.c: add wakeup supportRob Herring1-0/+2
Mark the pl031 as wake-up capable so that rtcwake and suspend test can work. Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: add support for spi rtc rx4581Torben Hohn3-0/+323
[akpm@linux-foundation.org: checkpatch fixes] Signed-off-by: Torben Hohn <torbenh@linutronix.de> Cc: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-tps65910.c: set irq flag to IRQF_EARLY_RESUME during irq requestLaxman Dewangan1-1/+1
All interrupt get disabled during system suspend and enabled during system resume. The enabling/disabling of interrupt happen in sequence of interrupt registration with framework. Therefore, in resume, the parent interrupt of this device enabled before the RTC irq interrupt enabled. If RTC is enabled for alarm wake and if system wake by alarm then there is interrupt pending for RTC. In resume, the parent interrupt get enabled before the rtc interrupt and hence ISR get served. In ISR, it founds that rtc interrupt is disabled and so it does not call the rtc isr handler and hence it misses the interrupt. Setting flag for early resume so that rtc interrupt get enabled before parent interrupt and so rtc interrupt get enabled when parent interrupt handler check for interrupt of device and call the rtc handler if it is there. This way it will not miss the interrupt. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-tps65910.c: use sleep_pm_ops macro for initialising ↵Laxman Dewangan1-9/+4
suspend/resume callbacks Use SET_SYSTEM_SLEEP_PM_OPS for setting suspend/resume callbacks for dev_pm_ops. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-tps65910.c: remove unnecessary irq stat save and restoreLaxman Dewangan1-19/+2
The driver stores the interrupt enable register before going to suspend and restore in resume. Also it enables alarm before going to suspend. The driver only write the Interrupt enable register for enabling ALARM and does not enable any other bits. So it is not require to save complete register and enable ALARM interrupt before suspend and restore in resume. Also ALARM interrupt already enable if alarm is enabled before going to suspend and hence it is not require to enable explictly in suspend. Removing such above code. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-tps65910.c: enable/disable wake in suspend/resumeLaxman Dewangan1-1/+11
Making the rtc driver as wakeup capabale and leaving the wake enable/disable decision to user space through a sysfs attribute. In suspend, enable wake if device wakeup enabled. In resume disable wake again. This change is inline with the Documentation/power/devices.txt# /sys/devices/.../power/wakeup files Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: add RTC driver for TPS80031/TPS80032Laxman Dewangan3-0/+358
Add an RTC driver for TPS80031/TPS80032 chips by TI. This driver supports: - Setting and getting time and date. - Setting and reading alarm time. - Alarm and interrupt functionlity. [akpm@linux-foundation.org: remove obsolete __devinit/__devexit] Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Devendra Naga <devendra.aaru@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: add new lp8788 rtc driverKim, Milo3-0/+351
TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight driver and current sinks. This patch enables LP8788 rtc module. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Cc: "devendra.aaru" <devendra.aaru@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-ds2404.c: use module_platform_driver macroSrinivas Kandagatla1-13/+1
Remove removes some code duplication by using module_platform_driver(). Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc: remove unnecessary semicolonsPeter Senna Tschudin2-2/+2
Found by Coccinelle: http://coccinelle.lip6.fr/ Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-pxa.c: avoid cpuid checkingHaojian Zhuang1-4/+1
pxa-rtc is widely used in pxa27x/pxa3xx/pxa93x/pxa95x. Checking cpuid in pxa-rtc driver is unnecessary since we assign on-chip device in soc files. Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc: use of_match_ptr() macroSachin Kamat6-7/+16
This eliminates having an #ifdef returning NULL for the case when OF is disabled. Maintains consistency in cases where OF is always selected. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc-pcf8523: add low battery voltage supportJesper Nilsson1-0/+31
Implement reading of the battery voltage low signal for rtc-pcf8523. The bit is read-only and cannot be cleared by software, so no clear function is implemented. [akpm@linux-foundation.org: omit pcf8563_rtc_ioctl() if CONFIG_RTC_INTF_DEV=n] Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21rtc: max77686: add Maxim 77686 driverJonghwa Lee3-0/+652
Add a driver to support max77686 rtc. MAX77686 rtc support smpl and wtsr mode. It has two alarm register which can be used for alarming to wake system up. This drvier uses regmap to access its register. [akpm@linux-foundation.org: remove inline, __devinit annotations] [jg1.han@samsung.com: fix build warnings] [akpm@linux-foundation.org: simplify code] Signed-off-by: Chiwoong Byun <woong.byun@samsung.com> Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com> Signed-off-by: Myugnjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-pxa.c: fix alarm can't wake up system issueLeo Song1-3/+4
Fix alarm can't wake up system issue Signed-off-by: Leo Song <liangs@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc/rtc-pxa.c: fix alarm not match issueLeo Song1-1/+10
Fix pxa rtc alarm issue by setting week of month and day of week in rdar/rdcr or it would not match. Signed-off-by: Leo Song <liangs@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21drivers/rtc: dump small buffers via %*phAndy Shevchenko3-44/+8
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-02-21Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds1-1/+1
Pull ARM SoC-specific updates from Arnd Bergmann: "This is a larger set of new functionality for the existing SoC families, including: - vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850 - prima2 gains support for the "marco" SoC family, its SMP based cousin - tegra gains support for the new Tegra4 (Tegra114) family - socfpga now supports a newer version of the hardware including SMP - i.mx31 and bcm2835 are now using DT probing for their clocks - lots of updates for sh-mobile - OMAP updates for clocks, power management and USB - i.mx6q and tegra now support cpuidle - kirkwood now supports PCIe hot plugging - tegra clock support is updated - tegra USB PHY probing gets implemented diffently" * tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits) ARM: prima2: remove duplicate v7_invalidate_l1 ARM: shmobile: r8a7779: Correct TMU clock support again ARM: prima2: fix __init section for cpu hotplug ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3) ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3) arm: socfpga: Add SMP support for actual socfpga harware arm: Add v7_invalidate_l1 to cache-v7.S arm: socfpga: Add entries to enable make dtbs socfpga arm: socfpga: Add new device tree source for actual socfpga HW ARM: tegra: sort Kconfig selects for Tegra114 ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114 ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC ARM: tegra: Fix build error for gic update ARM: tegra: remove empty tegra_smp_init_cpus() ARM: shmobile: Register ARM architected timer ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move ARM: shmobile: r8a7779: Correct TMU clock support ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles ARM: mxs: use apbx bus clock to drive the timers on timrotv2 ...
2013-02-21Merge tag 'staging-3.9-rc1' of ↵Linus Torvalds3-0/+309
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging tree update from Greg Kroah-Hartman: "Here's the big staging tree merge for 3.9-rc1 Lots of cleanups and updates for drivers all through the staging tree. We are pretty much "code neutral" here, adding just about as many lines as we removed. All of these have been in linux-next for a while." * tag 'staging-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (804 commits) staging: comedi: vmk80xx: wait for URBs to complete staging: comedi: drivers: addi-data: hwdrv_apci3200.c: Add a missing semicolon staging: et131x: Update TODO list staging: et131x: Remove assignment of skb->dev staging: wlan-ng: hfa384x.h: fix for error reported by smatch staging/zache checkpatch ERROR: spaces prohibited around that staging/ozwpan: Mark read only parameters and structs as const staging/ozwpan: Remove empty and unused function oz_cdev_heartbeat staging/ozwpan: Mark local functions as static (fix sparse warnings) staging/ozwpan: Add missing header includes staging/usbip: Mark local functions as static (fix sparse warnings) staging/xgifb: Remove duplicated code in loops. staging/xgifb: Consolidate return paths staging/xgifb: Remove code without effect staging/xgifb: Remove unnecessary casts staging/xgifb: Consolidate if/else if with identical code branches staging: vt6656: replaced custom TRUE definition with true staging: vt6656: replaced custom FALSE definition with false staging: vt6656: replace custom BOOL definition with bool staging/rtl8187se: Mark functions as static to silence sparse ...
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-17 03:00:10 +0000