summaryrefslogtreecommitdiff
path: root/drivers/net/wireless
AgeCommit message (Collapse)AuthorFilesLines
2009-08-28ipw2200: firmware DMA loading reworkZhu Yi1-53/+67
Bartlomiej Zolnierkiewicz reported an atomic order-6 allocation failure for ipw2200 firmware loading in kernel 2.6.30. High order allocation is likely to fail and should always be avoided. The patch fixes this problem by replacing the original order-6 pci_alloc_consistent() with an array of order-1 pages from a pci pool. This utilized the ipw2200 DMA command blocks (up to 64 slots). The maximum firmware size support remains the same (64*8K). This patch fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14016 Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Mel Gorman <mel@csn.ul.ie> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-21rtl8187: always set MSR_LINK_ENEDCA flag with RTL8187BHerton Ronaldo Krzesinski1-4/+10
RTL8187B always needs MSR_LINK_ENEDCA flag to be set even when it is in no link mode, otherwise it'll not be able to associate when this flag is not set after the change "mac80211: fix managed mode BSSID handling". By accident, setting BSSID of AP before association makes 8187B to successfuly associate even when ENEDCA flag isn't set, which was the case before the mac80211 change. But now the BSSID of AP we are trying to associate is only available after association is successful, and any attempt to associate without the needed flag doesn't work. Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-17orinoco: correct key bounds check in orinoco_hw_get_tkip_ivJohn W. Linville1-1/+1
If key is 4 that is an array out of bounds. Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-14rt2x00: fix memory corruption in rf cache, add a sanity checkPavel Roskin1-2/+4
Change rt2x00_rf_read() and rt2x00_rf_write() to subtract 1 from the rf register number. This is needed because the rf registers are enumerated starting with one. The size of the rf register cache is just enough to hold all registers, so writing to the highest register was corrupting memory. Add a check to make sure that the rf register number is valid. Signed-off-by: Pavel Roskin <proski@gnu.org> Cc: stable@kernel.org Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-12Revert "libertas: Read buffer overflow"David S. Miller1-8/+10
This reverts commit 57921c312e8cef72ba35a4cfe870b376da0b1b87. On request from John Linville: It has been shown to create a new problem. There is work towards a solution to that one, but it isn't a simple clean-up. Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-10ar9170: fix read & write outside array boundsDan Carpenter1-2/+3
queue == __AR9170_NUM_TXQ would cause a bug on the next line. found by Smatch ( http://repo.or.cz/w/smatch.git ). Cc: stable@kernel.org Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-10ar9170usb: fix spurious firmware related messageChristian Lamparter1-1/+5
When ar9170-2.fw was missing, the driver erroneously complained about missing the initialization values file ar9170-1.fw... Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-09Merge branch 'master' of /home/davem/src/GIT/linux-2.6/David S. Miller2-16/+6
2009-08-07libertas: correct packing of rxpd structureBob Dunlop1-2/+2
Older Gcc compilers (3.4.5 tested) need additional hints in order to get the packing of the rxpd structure (which contains a 16 bit union) correct on the ARM processor. struct txpd does not need these hints since it contains a 32 bit union that packs naturally. Signed-off-by: R.J.Dunlop <rdunlop@guralp.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-07mwl8k: prevent module unload hangLennert Buytenhek1-2/+2
We need to unregister our ieee80211_hw before resetting the chip, as the former causes firmware commands to be issued which will time out once the chip has been reset. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-07mwl8k: prevent crash in ->configure_filter() if no interface was addedLennert Buytenhek1-4/+8
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-07mwl8k: call pci_unmap_single() before accessing command structure againLennert Buytenhek1-2/+3
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-07mwl8k: add various missing GET_HW_SPEC endian conversionsLennert Buytenhek1-4/+4
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-07mwl8k: fix NULL pointer dereference on receive out-of-memoryLennert Buytenhek1-0/+2
When we go into out-of-memory and fail to allocate skbuffs to refill the receive ring with, rxq_process can end up running into a receive ring entry that is marked as host-owned but doesn't have an associated skbuff. If this happens, we must break out of the rx processing loop instead of trying to process the descriptor. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Acked-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-07ipw2x00: Write outside array boundsZhu Yi1-1/+1
> channel_index loops up to IPW_SCAN_CHANNELS, but is used after being > incremented. This might be able to access 1 past the end of the array Reported-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds15-43/+62
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits) ehea: Fix napi list corruption on ifconfig down igbvf: Allow VF driver to correctly recognize failure to set mac 3c59x: Fix build failure with gcc 3.2 sky2: Avoid transmits during sky2_down() iwlagn: do not send key clear commands when rfkill enabled libertas: Read buffer overflow drivers/net/wireless: introduce missing kfree drivers/net/wireless/iwlwifi: introduce missing kfree zd1211rw: fix unaligned access in zd_mac_rx cfg80211: fix regression on beacon world roaming feature cfg80211: add two missing NULL pointer checks ixgbe: Patch to modify 82598 PCIe completion timeout values bluetooth: rfcomm_init bug fix mlx4_en: Fix double pci unmapping. mISDN: Fix handling of receive buffer size in L1oIP pcnet32: VLB support fixes pcnet32: remove superfluous NULL pointer check in pcnet32_probe1() net: restore the original spinlock to protect unicast list netxen: fix coherent dma mask setting mISDN: Read buffer overflow ...
2009-08-03iwlagn: do not send key clear commands when rfkill enabledReinette Chatre1-0/+12
Do all key clearing except sending sommands to device when rfkill enabled. When rfkill enabled the interface is brought down and will be brought back up correctly after rfkill is enabled again. Same change is not needed for iwl3945 as it ignores return code when sending key clearing command to device. This fixes http://bugzilla.kernel.org/show_bug.cgi?id=13742 Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Tested-by: Frans Pop <elendil@planet.nl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-03libertas: Read buffer overflowRoel Kluin1-1/+1
Check whether index is within bounds before testing the element. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-03drivers/net/wireless: introduce missing kfreeJulia Lawall1-0/+1
Error handling code following a kzalloc should free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-03drivers/net/wireless/iwlwifi: introduce missing kfreeJulia Lawall1-6/+6
Move orthogonal error handling code up before a kzalloc, so that it doesn't have to free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-03zd1211rw: fix unaligned access in zd_mac_rxPatrick Simmons1-1/+1
Fix an unaligned memory access in the zd_mac_rx function of zd1211rw that causes problems on SPARC64. Signed-off-by: Patrick Simmons <linuxrocks123@netscape.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-03cfg80211: fix regression on beacon world roaming featureLuis R. Rodriguez2-0/+6
A regression was added through patch a4ed90d6: "cfg80211: respect API on orig_flags on channel for beacon hint" We did indeed respect _orig flags but the intention was not clearly stated in the commit log. This patch fixes firmware issues picked up by iwlwifi when we lift passive scan of beaconing restrictions on channels its EEPROM has been configured to always enable. By doing so though we also disallowed beacon hints on devices registering their wiphy with custom world regulatory domains enabled, this happens to be currently ath5k, ath9k and ar9170. The passive scan and beacon restrictions on those devices would never be lifted even if we did find a beacon and the hardware did support such enhancements when world roaming. Since Johannes indicates iwlwifi firmware cannot be changed to allow beacon hinting we set up a flag now to specifically allow drivers to disable beacon hints for devices which cannot use them. We enable the flag on iwlwifi to disable beacon hints and by default enable it for all other drivers. It should be noted beacon hints lift passive scan flags and beacon restrictions when we receive a beacon from an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz band. We don't bother with channels 1-11 as those channels are allowed world wide. This should fix world roaming for ath5k, ath9k and ar9170, thereby improving scan time when we receive the first beacon from any AP, and also enabling beaconing operation (AP/IBSS/Mesh) on cards which would otherwise not be allowed to do so. Drivers not using custom regulatory stuff (wiphy_apply_custom_regulatory()) were not affected by this as the orig_flags for the channels would have been cleared upon wiphy registration. I tested this with a world roaming ath5k card. Cc: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-29libertas: Read buffer overflowRoel Kluin1-10/+8
Several arrays were read before checking whether the index was within bounds. ARRAY_SIZE() should be used to determine the size of arrays. rates->rates has an arraysize of 1, so calling get_common_rates() with a rates_size of MAX_RATES (14) was causing reads out of bounds. tmp_size can increment at most to (ARRAY_SIZE(lbs_bg_rates) - 1) * (*rates_size - 1), so that should be the number of elements of tmp[]. A goto can be eliminated: ret was already set upon its declaration. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-29libertas: Read outside array boundsRoel Kluin1-1/+2
reads bss->rates[j] before checking bounds of index, and should use ARRAY_SIZE to determine the size of the array. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds13-15/+55
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits) cnic: Fix ISCSI_KEVENT_IF_DOWN message handling. net: irda: init spinlock after memcpy ixgbe: fix for 82599 errata marking UDP checksum errors r8169: WakeOnLan fix for the 8168 netxen: reset ring consumer during cleanup net/bridge: use kobject_put to release kobject in br_add_if error path smc91x.h: add config for Nomadik evaluation kit NET: ROSE: Don't use static buffer. eepro: Read buffer overflow tokenring: Read buffer overflow at1700: Read buffer overflow fealnx: Write outside array bounds ixgbe: remove unnecessary call to device_init_wakeup ixgbe: Don't priority tag control frames in DCB mode ixgbe: Enable FCoE offload when DCB is enabled for 82599 net: Rework mdio-ofgpio driver to use of_mdio infrastructure register at91_ether using platform_driver_probe skge: Enable WoL by default if supported net: KS8851 needs to depend on MII be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly. ...
2009-07-27iwlwifi: Read outside array boundsRoel Kluin1-0/+2
tid is bounded (above) by the size of default_tid_to_tx_fifo (17 elements), but the size of priv->stations[].tid[] is MAX_TID_COUNT (9) elements. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27ath9k: Read outside array boundsRoel Kluin1-2/+2
Incorrect limits leads to reads outside array bounds. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27airo: Buffer overflowRoel Kluin1-7/+6
SSID_rid has space for only 3 ssids. txPowerLevels[i] is read before the bounds check for i Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27wireless: ERR_PTR vs nullDan Carpenter1-4/+2
iwm_wdev_alloc() returns an ERR_PTR on failure and not null. It also prints its own dev_err() message so I removed that as well. Compile tested only. Sorry. Found by smatch (http://repo.or.cz/w/smatch.git). Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27iwlagn: fix minimum number of queues settingreinette chatre3-5/+7
We need to provide a reasonable minimum that will result in a working setup if used. Set minimum to be 10 to provide for 4 standard TX queues + 1 command queue + 2 (unused) HCCA queues + 4 HT queues (one per AC). We allow the user to change the number of queues used via a module parameter and use this minimum value to check if it is valid. Without this patch a user can select a value for the number of queues that will result in a failing setup. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Reviewed-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-27iwlwifi: fix TX queue raceJohannes Berg1-6/+6
I had a problem on 4965 hardware (well, probably other hardware too, but others don't survive my stress testing right now, unfortunately) where the driver was sending invalid commands to the device, but no such thing could be seen from the driver's point of view. I could reproduce this fairly easily by sending multiple TCP streams with iperf on different TIDs, though sometimes a single iperf stream was sufficient. It even happened with a single core, but I have forced preemption turned on. The culprit was a queue overrun, where we advanced the queue's write pointer over the read pointer. After careful analysis I've come to the conclusion that the cause is a race condition between iwlwifi and mac80211. mac80211, of course, checks whether the queue is stopped, before transmitting a frame. This effectively looks like this: lock(queues) if (stopped(queue)) { unlock(queues) return busy; } unlock(queues) ... <-- this place will be important there is some more code here drv_tx(frame) The driver, on the other hand, can stop and start queues, which does lock(queues) mark_running/stopped(queue) unlock(queues) [if marked running: wake up tasklet to send pending frames] Now, however, once the driver starts the queue, mac80211 can see that and end up at the marked place above, at which point for some reason the driver seems to stop the queue again (I don't understand that) and then we end up transmitting while the queue is actually full. Now, this shouldn't actually matter much, but for some reason I've seen it happen multiple times in a row and the queue actually overflows, at which point the queue bites itself in the tail and things go completely wrong. This patch fixes this by just dropping the packet should this have happened, and making the lock in iwlwifi cover everything so iwlwifi can't race against itself (dropping the lock there might make it more likely, but it did seem to happen without that too). Since we can't hold the lock across drv_tx() above, I see no way to fix this in mac80211, but I also don't understand why I haven't seen this before -- maybe I just never stress tested it this badly. With this patch, the device has survived many minutes of simultanously sending two iperf streams on different TIDs with combined throughput of about 60 Mbps. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21libertas: Fix problem with broken V4 firmware on CF8381Marek Vasut2-1/+9
Firmware V4 on CF8381 reports region code shifted by 1 byte to left. The following patch checks for this and handles it properly. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21ath: add support for special 0x8000 regulatory domainLuis R. Rodriguez1-0/+17
Two users of ar9170 devices have now reported their cards have been programmed with a regulatory domain of 0x8000. This is not a valid regulatory domain as such these users were unable to use these devices. Since this doesn't seem to be a device EEPROM corruption we must treat it specially. It may have been possible the manufacturer intended to use 0x0 as the regulatory domain and that would ultimately yield to US but since we cannot get confirmationf or this we default this special case to one of our world regulatory domains, specifically 0x64. Reported-by: DavidFreeman on #linux-wireless Reported-by: Joerg Albert <jal2@gmx.de> Cc: Christian Lamparter <chunkeey@web.de>, Cc: Stephen Chen <stephen.chen@atheros.com> Cc: David Quan <david.quan@atheros.com> Cc: Tony Yang <tony.yang@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21p54spi: fix potential null deref in p54spi.cDan Carpenter1-1/+1
Fix a potential NULL dereference bug during error handling in p54spi_probe. This bug was discovered by smatch: (http://repo.or.cz/w/smatch.git). Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21ath9k: Tune ANI function processing on AP mode during ANI resetLuis R. Rodriguez1-0/+12
For AP mode we must tune ANI specially for 2 GHz and for 5 GHz. We mask in only the flags we want to toggle on ath9k_hw_ani_control() through the ah->ani_function bitmask, this will take care of ignoring changes during ANI reset which we were disabling before. Testedy-by: Steven Luo <steven@steven676.net> Cc: Bennyam Malavazi <bennyam.malavazi@atheros.com> Cc: Jouni Malinen <jouni.malinen@Atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21rt2x00: Fix chipset detection for rt2500usbAndy Whitcroft1-1/+3
The commit below changed the semantics of rt2x00_check_rev so that it no longer checked the bottom 4 bits of the rev were non-zero. During that conversion this part of the check was not propogated to the rt2500usb initialisation. commit 358623c22c9fd837b3b1b444377037f72553dc9f Author: Ivo van Doorn <ivdoorn@gmail.com> Date: Tue May 5 19:46:08 2009 +0200 rt2x00: Simplify rt2x00_check_rev Without this check rt73 devices are miss recognised as rt2500 devices and two drivers are loaded. Preventing the device being used. Reinstate this check. Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21rtl8187: Fix for kernel oops when unloading with LEDs enabledLarry Finger1-1/+2
When rtl8187 is unloaded and CONFIG_RTL8187_LEDS is set, the kernel may oops when the module is unloaded as the workqueue for led_on was not being cancelled. This patch fixes the problem reported in http://marc.info/?l=linux-wireless&m=124742957615781&w=2. Reported-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21ath5k: temporarily disable crypto for AP modeBob Copeland1-0/+3
Pavel Roskin reported some issues with using AP mode without nohwcrypt=1. Most likely this is similar to the problem fixed some time ago in ath9k by 3f53dd64f192450cb331c0fecfc26ca952fb242f, "ath9k: Fix hw crypto configuration for TKIP in AP mode." That only affects TKIP but it's easiest to just disable that and WEP too until we get a proper fix in. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21mac80211_hwsim: fix use after freeJohannes Berg1-2/+2
Once the "data" pointer is freed, we can't be iterating to the next item in the list any more so we need to use list_for_each_entry_safe with a temporary variable. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21mac80211_hwsim: fix unregistrationJohannes Berg1-1/+1
If you rmmod the module while associated, frames might be transmitted during unregistration -- which will crash if the hwsim%d interface is unregistered first, so only do that after all the virtual wiphys are gone. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21iwlwifi: only update byte count table during aggregationReinette Chatre1-1/+2
The byte count table is only used for aggregation. Updating it in other cases caused fragmented frames to be dropped. This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2004 Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21iwlwifi: only show active power level via sysfsReinette Chatre2-6/+2
This changes the power_level file to adhere to the "one value per file" sysfs rule. The user will know which power level was requested as it will be the number just written to this file. It is thus not necessary to create a new sysfs file for this value. In addition it fixes a problem where powertop's parsing expects this value to be the first value in this file without any descriptions. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-21iwmc3200wifi: fix NULL pointer dereference in iwm_if_freeZhu Yi1-1/+1
The driver private data is now based on wiphy. So we should not touch the private data after wiphy_free() is called. The patch fixes the potential NULL pointer dereference by making the iwm_wdev_free() the last one on the interface removal path. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds1-1/+2
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: Revert "NET: Fix locking issues in PPP, 6pack, mkiss and strip line disciplines." skbuff.h: Fix comment for NET_IP_ALIGN drivers/net: using spin_lock_irqsave() in net_send_packet() NET: phy_device, fix lock imbalance gre: fix ToS/DiffServ inherit bug igb: gcc-3.4.6 fix atlx: duplicate testing of MCAST flag NET: Fix locking issues in PPP, 6pack, mkiss and strip line disciplines. netdev: restore MTU change operation netdev: restore MAC address set and validate operations sit: fix regression: do not release skb->dst before xmit net: ip_push_pending_frames() fix net: sk_prot_alloc() should not blindly overwrite memory
2009-07-14Revert "NET: Fix locking issues in PPP, 6pack, mkiss and strip line ↵David S. Miller1-24/+15
disciplines." This reverts commit adeab1afb7de89555c69aab5ca21300c14af6369. As Alan Cox explained, the TTY layer changes that went recently to get rid of the tty->low_latency stuff fixes this already, and even for -stable it's the ->low_latency changes that should go in to fix this, rather than this patch. Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-12NET: Fix locking issues in PPP, 6pack, mkiss and strip line disciplines.Ralf Baechle1-15/+24
Guido Trentalancia reports: I am trying to use the kiss driver in the Linux kernel that is being shipped with Fedora 10 but unfortunately I get the following oops: mkiss: AX.25 Multikiss, Hans Albas PE1AYX mkiss: ax0: crc mode is auto. ADDRCONF(NETDEV_CHANGE): ax0: link becomes ready ------------[ cut here ]------------ WARNING: at kernel/softirq.c:77 __local_bh_disable+0x2f/0x83() (Not tainted) [...] unloaded: microcode] Pid: 0, comm: swapper Not tainted 2.6.27.25-170.2.72.fc10.i686 #1 [<c042ddfb>] warn_on_slowpath+0x65/0x8b [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38 [<c04228b4>] ? __enqueue_entity+0xe3/0xeb [<c042431e>] ? enqueue_entity+0x203/0x20b [<c0424361>] ? enqueue_task_fair+0x3b/0x3f [<c041f88c>] ? resched_task+0x3a/0x6e [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38 [<c06ab4e2>] ? _spin_lock_bh+0xb/0x16 [<c043255b>] __local_bh_disable+0x2f/0x83 [<c04325ba>] local_bh_disable+0xb/0xd [<c06ab4e2>] _spin_lock_bh+0xb/0x16 [<f8b6f600>] mkiss_receive_buf+0x2fb/0x3a6 [mkiss] [<c0572a30>] flush_to_ldisc+0xf7/0x198 [<c0572b12>] tty_flip_buffer_push+0x41/0x51 [<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio] [<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio] [<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93 [<c05ea290>] uhci_giveback_urb+0xe5/0x15f [<c05eaabf>] uhci_scan_schedule+0x52e/0x767 [<c05f6288>] ? psmouse_handle_byte+0xc/0xe5 [<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1 [<c05ec5b0>] uhci_irq+0x110/0x125 [<c05d4834>] usb_hcd_irq+0x40/0xa3 [<c0465313>] handle_IRQ_event+0x2f/0x64 [<c046642b>] handle_level_irq+0x74/0xbe [<c04663b7>] ? handle_level_irq+0x0/0xbe [<c0406e6e>] do_IRQ+0xc7/0xfe [<c0405668>] common_interrupt+0x28/0x30 [<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d [<c0617f52>] cpuidle_idle_call+0x60/0x92 [<c0403c61>] cpu_idle+0x101/0x134 [<c069b1ba>] rest_init+0x4e/0x50 ======================= ---[ end trace b7cc8076093467ad ]--- ------------[ cut here ]------------ WARNING: at kernel/softirq.c:136 _local_bh_enable_ip+0x3d/0xc4() [...] Pid: 0, comm: swapper Tainted: G W 2.6.27.25-170.2.72.fc10.i686 [<c042ddfb>] warn_on_slowpath+0x65/0x8b [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38 [<c04228b4>] ? __enqueue_entity+0xe3/0xeb [<c042431e>] ? enqueue_entity+0x203/0x20b [<c0424361>] ? enqueue_task_fair+0x3b/0x3f [<c041f88c>] ? resched_task+0x3a/0x6e [<c06ab62b>] ? _spin_unlock_irqrestore+0x22/0x38 [<c06ab4e2>] ? _spin_lock_bh+0xb/0x16 [<f8b6f642>] ? mkiss_receive_buf+0x33d/0x3a6 [mkiss] [<c04325f9>] _local_bh_enable_ip+0x3d/0xc4 [<c0432688>] local_bh_enable_ip+0x8/0xa [<c06ab54d>] _spin_unlock_bh+0x11/0x13 [<f8b6f642>] mkiss_receive_buf+0x33d/0x3a6 [mkiss] [<c0572a30>] flush_to_ldisc+0xf7/0x198 [<c0572b12>] tty_flip_buffer_push+0x41/0x51 [<f89477f2>] ftdi_process_read+0x375/0x4ad [ftdi_sio] [<f8947a5a>] ftdi_read_bulk_callback+0x130/0x138 [ftdi_sio] [<c05d4bec>] usb_hcd_giveback_urb+0x63/0x93 [<c05ea290>] uhci_giveback_urb+0xe5/0x15f [<c05eaabf>] uhci_scan_schedule+0x52e/0x767 [<c05f6288>] ? psmouse_handle_byte+0xc/0xe5 [<c054df78>] ? acpi_ev_gpe_detect+0xd6/0xe1 [<c05ec5b0>] uhci_irq+0x110/0x125 [<c05d4834>] usb_hcd_irq+0x40/0xa3 [<c0465313>] handle_IRQ_event+0x2f/0x64 [<c046642b>] handle_level_irq+0x74/0xbe [<c04663b7>] ? handle_level_irq+0x0/0xbe [<c0406e6e>] do_IRQ+0xc7/0xfe [<c0405668>] common_interrupt+0x28/0x30 [<c056821a>] ? acpi_idle_enter_simple+0x162/0x19d [<c0617f52>] cpuidle_idle_call+0x60/0x92 [<c0403c61>] cpu_idle+0x101/0x134 [<c069b1ba>] rest_init+0x4e/0x50 ======================= ---[ end trace b7cc8076093467ad ]--- mkiss: ax0: Trying crc-smack mkiss: ax0: Trying crc-flexnet The issue was, that the locking code in mkiss was assuming it was only ever being called in process or bh context. Fixed by converting the involved locking code to use irq-safe locks. Review of other networking line disciplines shows that 6pack, both sync and async PPP and STRIP have similar issues. The ppp_async one is the most interesting one as it sorts out half of the issue as far back as 2004 in commit http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commitdiff;h=2996d8deaeddd01820691a872550dc0cfba0c37d Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Reported-by: Guido Trentalancia <guido@trentalancia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-12netdev: restore MAC address set and validate operationsBen Hutchings1-1/+2
alloc_etherdev() used to install default implementations of these operations, but they must now be explicitly installed in struct net_device_ops. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds11-8/+37
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits) cxgb3: Fix crash caused by stashing wrong netdev_queue ixgbe: Fix coexistence of FCoE and Flow Director in 82599 memory barrier: adding smp_mb__after_lock net: adding memory barrier to the poll and receive callbacks netpoll: Fix carrier detection for drivers that are using phylib includecheck fix: include/linux, rfkill.h p54: tx refused but queue active Atheros Kconfig needs to be dependent on WLAN_80211 mac80211: fix docbook mac80211_hwsim: avoid NULL access ssb: Add support for 4318E b43: Add support for 4318E zd1211rw: adding SONY IFU-WLM2 (054c:0257) as a zd1211b device zd1211rw: 07b8:6001 is a ZD1211B r6040: bump driver version to 0.24 and date to 08 July 2009 r6040: restore MIER register correctly when IRQ line is shared ipv4: Fix fib_trie rebalancing, part 4 (root thresholds) davinci_emac: fix kernel oops when changing MAC address while interface is down igb: set lan id prior to configuring phy mac80211: minstrel: avoid accessing negative indices in rix_to_ndx() ...
2009-07-08p54: tx refused but queue activeLarry Finger1-2/+3
In the mainline kernel, p54usb will fail because the TX queue length can become < 0. This problem has been reported as Bugzilla #13725. The failure is expressed by the following message in the logs: WARNING: at net/mac80211/tx.c:1325 ieee80211_tx+0x23c/0x298 [mac80211]() Hardware name: HP Pavilion dv2700 Notebook PC tx refused but queue active This problem has been recently observed in the wireless-testing tree, where a full solution is being tested. That fix is too invasive for 2.6.31-rcX, but the simple change supplied here will prevent the failure. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-08Atheros Kconfig needs to be dependent on WLAN_80211Jay Sternberg1-0/+1
Atheros top level menu needs a "depends WLAN_80211" to properly indent within menuconfig and xconfig interfaces. This is purely a visual issue but it effects all subsequent drivers. The issue is the top level menu does not include a dependency on WLAN_80211 so within the tree structure, Atheros is at the same level as WLAN_80211 but when WLAN_80211 collapsed, the menu disappears along with all subsequent drives, so it is really a subordinate. Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-22 17:44:26 +0000