| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 4fbae7d83c98c30efc ("ipvlan: Introduce l3s mode") added
registration of netfilter hooks via nf_register_hooks().
This API provides the illusion of 'global' netfilter hooks by placing the
hooks in all current and future network namespaces.
In case of ipvlan the hook appears to be only needed in the namespace
that contains the ipvlan master device (i.e., usually init_net), so
placing them in all namespaces is not needed.
This switches ipvlan driver to pernet operations, and then only registers
hooks in namespaces where a ipvlan master device is set to l3s mode.
Extra care has to be taken when the master device is moved to another
namespace, as we might have to 'move' the netfilter hooks too.
This is done by storing the namespace the ipvlan port was created in.
On REGISTER event, do (un)register operations in the old/new namespaces.
This will also allow removal of the nf_register_hooks() in a future patch.
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a tap character device driver that is based on the
IP-VLAN network interface, called ipvtap. An ipvtap device can be created
in the same way as an ipvlan device, using 'type ipvtap', and then accessed
using the tap user space interface.
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPvlan checks if the master device is already used by checking a
specific device (here it's macvlan device). This is technically not
sufficient and it should just ensure the rx_handler is busy or not.
This would be a super check that includes macvlan and any other that
has already registered rx-handler.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the last patch da36e13cf65 ("ipvlan: improvise dev_id generation
logic in IPvlan") I missed some part of Dave's suggestion and because
of that the dev_id creation could fail in a corner case scenario. This
would happen when more or less 64k devices have been already created and
several have been deleted. If the devices that are still sticking around
are the last n bits from the bitmap. So in this scenario even if lower
bits are available, the dev_id search is so narrow that it always fails.
Fixes: da36e13cf65 ("ipvlan: improvise dev_id generation logic in IPvlan")
CC: David Miller <davem@davemloft.org>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch 009146d117b ("ipvlan: assign unique dev-id for each slave
device.") used ida_simple_get() to generate dev_ids assigned to the
slave devices. However (Eric has pointed out that) there is a shortcoming
with that approach as it always uses the first available ID. This
becomes a problem when a slave gets deleted and a new slave gets added.
The ID gets reassigned causing the new slave to get the same link-local
address. This side-effect is undesirable.
This patch adds a per-port variable that keeps track of the IDs
assigned and used as the stat-base for the IDR api. This base will be
wrapped around when it reaches the MAX (0xFFFE) value possibly on a
busy system where slaves are added and deleted routinely.
Fixes: 009146d117b ("ipvlan: assign unique dev-id for each slave device.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
CC: David Miller <davem@davemloft.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPvlan setup uses one mac-address (of master). The IPv6 link-local
addresses are derived using the mac-address on the link. Lack of
dev-ids makes these link-local addresses same for all slaves including
that of master device. dev-ids are necessary to add differentiation
when L2 address is shared.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are three functions which would invoke the ipvlan_count_rx. They
are ipvlan_process_multicast, ipvlan_rcv_frame, and ipvlan_nf_input.
The former two functions already use the ipvlan directly before
ipvlan_count_rx, and ipvlan_nf_input gets the ipvlan from
ipvl_addr->master, it is not possible to be NULL too.
So the ipvlan pointer check is unnecessary in ipvlan_count_rx.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add or del IP address
There are some duplicated codes in ipvlan_add_addr6/4 and
ipvlan_del_addr6/4. Now define two common functions ipvlan_add_addr
and ipvlan_del_addr to decrease the duplicated codes.
It could be helful to maintain the codes.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In an IPvlan setup when master is set in loopback mode e.g.
ethtool -K eth0 set loopback on
where eth0 is master device for IPvlan setup.
The failure is caused by the faulty logic that determines if the
packet is from TX-path vs. RX-path by just looking at the mac-
addresses on the packet while processing multicast packets.
In the loopback-mode where this crash was happening, the packets
that are sent out are reflected by the NIC and are processed on
the RX path, but mac-address check tricks into thinking this
packet is from TX path and falsely uses dev_forward_skb() to pass
packets to the slave (virtual) devices.
This patch records the path while queueing packets and eliminates
logic of looking at mac-addresses for the same decision.
------------[ cut here ]------------
kernel BUG at include/linux/skbuff.h:1737!
Call Trace:
[<ffffffff921fbbc2>] dev_forward_skb+0x92/0xd0
[<ffffffffc031ac65>] ipvlan_process_multicast+0x395/0x4c0 [ipvlan]
[<ffffffffc031a9a7>] ? ipvlan_process_multicast+0xd7/0x4c0 [ipvlan]
[<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
[<ffffffff91cdff09>] process_one_work+0x1a9/0x660
[<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
[<ffffffff91ce086d>] worker_thread+0x11d/0x360
[<ffffffff91ce0750>] ? rescuer_thread+0x350/0x350
[<ffffffff91ce960b>] kthread+0xdb/0xe0
[<ffffffff91c05c70>] ? _raw_spin_unlock_irq+0x30/0x50
[<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0
[<ffffffff92348b7a>] ret_from_fork+0x9a/0xd0
[<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0
Fixes: ba35f8588f47 ("ipvlan: Defer multicast / broadcast processing to a work-queue")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) netif_rx() / dev_forward_skb() should not be called from process
context.
2) ipvlan_count_rx() should be called with preemption disabled.
3) We should check if ipvlan->dev is up before feeding packets
to netif_rx()
4) We need to prevent device from disappearing if some packets
are in the multicast backlog.
5) One kfree_skb() should be a consume_skb() eventually
Fixes: ba35f8588f47 ("ipvlan: Defer multicast / broadcast processing to
a work-queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two functions which would free the ipvl_port now. The first
is ipvlan_port_create. It frees the ipvl_port in the error handler,
so it could kfree it directly. The second is ipvlan_port_destroy. It
invokes netdev_rx_handler_unregister which enforces one grace period
by synchronize_net firstly, so it also could kfree the ipvl_port
directly and safely.
So it is unnecessary to use kfree_rcu to free ipvl_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mtu_adj is initialized to zero when alloc mem, there is no any
assignment to mtu_adj. It is only used in ipvlan_adjust_mtu as one
right value.
So it is useless member of struct ipvl_dev, then remove it.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ipvlan_link_new fails and creates one ipvlan port, it does not
destroy the ipvlan port created. It causes mem leak and the physical
device contains invalid ipvlan data.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This l3mdev_ops structure is only stored in the l3mdev_ops field of a
net_device structure. This field is declared const, so the l3mdev_ops
structure can be declared as const also. Additionally drop the
__read_mostly annotation.
The semantic patch that adds const is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct l3mdev_ops i@p = { ... };
@ok@
identifier r.i;
struct net_device *e;
position p;
@@
e->l3mdev_ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct l3mdev_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct l3mdev_ops i = { ... };
// </smpl>
The effect on the layout of the .o file is shown by the following output
of the size command, first before then after the transformation:
text data bss dec hex filename
7364 466 52 7882 1eca drivers/net/ipvlan/ipvlan_main.o
7412 434 52 7898 1eda drivers/net/ipvlan/ipvlan_main.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a typical IPvlan L3 setup where master is in default-ns and
each slave is into different (slave) ns. In this setup egress
packet processing for traffic originating from slave-ns will
hit all NF_HOOKs in slave-ns as well as default-ns. However same
is not true for ingress processing. All these NF_HOOKs are
hit only in the slave-ns skipping them in the default-ns.
IPvlan in L3 mode is restrictive and if admins want to deploy
iptables rules in default-ns, this asymmetric data path makes it
impossible to do so.
This patch makes use of the l3_rcv() (added as part of l3mdev
enhancements) to perform input route lookup on RX packets without
changing the skb->dev and then uses nf_hook at NF_INET_LOCAL_IN
to change the skb->dev just before handing over skb to L4.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The earlier patch c3aaa06d5a63 (ipvlan: scrub skb before routing
in L3 mode.) did this but only for TX path in L3 mode. This
patch extends it for both the modes for TX/RX path.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a qdisc is used on a ipvlan device, we need to use different
lockdep classes to avoid false positives.
Use the new netdev_lockdep_set_classes() generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When newlink creation fails at device-registration, the port->count
is decremented twice. Francesco Ruggeri (fruggeri@arista.com) found
this issue in Macvlan and the same exists in IPvlan driver too.
While fixing this issue I noticed another issue of missing unregister
in case of failure, so adding it to the fix which is similar to the
macvlan fix by Francesco in commit 308379607548 ("macvlan: fix failure
during registration v3")
Reported-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vlan drivers lack proper propagation of gso_max_segs from
lower device.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. scope correction for few functions that are used in single file.
2. Adjust variables that are used in fast-path to fit into single cacheline
3. Update rcv_frame() to skip shared check for frames coming over wire
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mode argument was erronusly defined as u32 but it has always
been u16. Also use ipvlan_set_mode() helper to set the mode instead
of assigning directly. This should avoid future erronus assignments /
updates.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Scrub skb before hitting the iptable hooks to ensure packets hit
these hooks. Set the xnet param only when the packet is crossing the
ns boundry so if the IPvlan slave and master belong to the same ns,
the param will be set to false.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we create IPvlan slave; we use ether_setup() and that
sets up default MTU to 1500 while the master device may have
lower / different MTU. Any subsequent changes to the masters'
MTU are reflected into the slaves' MTU setting. However if those
don't happen (most likely scenario), the slaves' MTU stays at
1500 which could be bad.
This change adds code to inherit MTU from the master device
instead of using the default value during the link initialization
phase.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tim Hockins <thockins@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the ipv4 outbound path of an ipvlan device in l3 mode, the ifindex is
being grabbed from dev_get_iflink. This works for the physical device
case, since as the documentation of that function notes: "Physical
interfaces have the same 'ifindex' and 'iflink' values.". However, if
the master device is a veth, and the pairs are in separate net
namespaces, the route lookup will fail with -ENODEV due to outer veth
pair being in a separate namespace from the ipvlan master/routing
namespace.
ns0 | ns1 | ns2
veth0a--|--veth0b--|--ipvl0
In ipvlan_process_v4_outbound(), a packet sent from ipvl0 in the above
configuration will pass fl.flowi4_oif == veth0a to
ip_route_output_flow(), but *net == ns1.
Notice also that ipv6 processing is not using iflink. Since there is a
discrepancy in usage, fixup both v4 and v6 case to use local dev
variable.
Tested this with l3 ipvlan on top of veth, as well as with single
physical interface in the top namespace.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compute net once in ipvlan_process_v4_outbound and
ipvlan_process_v6_outbound and store it in a variable so that net does
not need to be recomputed next time it is used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop hidding the sk parameter with an inline helper function and make
all of the callers pass it, so that it is clear what the function is
doing.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is confusing and silly hiding a parameter so modify all of
the callers to pass in the appropriate socket or skb->sk if
no socket is known.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Phil Sutter <phil@nwl.cc>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inet6addr notifier is atomic and runs in bh context without RTNL when
ipv6 receives router advertisement packet and performs autoconfiguration.
Proper fix still in discussion. Let's at least plug the bug.
v1: http://lkml.kernel.org/r/20150514135618.14062.1969.stgit@buzz
v2: http://lkml.kernel.org/r/20150703125840.24121.91556.stgit@buzz
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In tx path rcu_read_lock_bh() is held, so we need rcu_deference_bh().
This fixes the following warning:
===============================
[ INFO: suspicious RCU usage. ]
4.1.0-rc1+ #1007 Not tainted
-------------------------------
drivers/net/ipvlan/ipvlan.h:106 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by dhclient/1076:
#0: (rcu_read_lock_bh){......}, at: [<ffffffff817e8d84>] rcu_lock_acquire+0x0/0x26
stack backtrace:
CPU: 2 PID: 1076 Comm: dhclient Not tainted 4.1.0-rc1+ #1007
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
0000000000000001 ffff8800d381bac8 ffffffff81a4154f 000000003c1a3c19
ffff8800d4d0a690 ffff8800d381baf8 ffffffff810b849f ffff880117d41148
ffff880117d40000 ffff880117d40068 0000000000000156 ffff8800d381bb18
Call Trace:
[<ffffffff81a4154f>] dump_stack+0x4c/0x65
[<ffffffff810b849f>] lockdep_rcu_suspicious+0x107/0x110
[<ffffffff8165a522>] ipvlan_port_get_rcu+0x47/0x4e
[<ffffffff8165ad14>] ipvlan_queue_xmit+0x35/0x450
[<ffffffff817ea45d>] ? rcu_read_unlock+0x3e/0x5f
[<ffffffff810a20bf>] ? local_clock+0x19/0x22
[<ffffffff810b4781>] ? __lock_is_held+0x39/0x52
[<ffffffff8165b64c>] ipvlan_start_xmit+0x1b/0x44
[<ffffffff817edf7f>] dev_hard_start_xmit+0x2ae/0x467
[<ffffffff817ee642>] __dev_queue_xmit+0x50a/0x60c
[<ffffffff817ee7a7>] dev_queue_xmit_sk+0x13/0x15
[<ffffffff81997596>] dev_queue_xmit+0x10/0x12
[<ffffffff8199b41c>] packet_sendmsg+0xb6b/0xbdf
[<ffffffff810b5ea7>] ? mark_lock+0x2e/0x226
[<ffffffff810a1fcc>] ? sched_clock_cpu+0x9e/0xb7
[<ffffffff817d56f9>] sock_sendmsg_nosec+0x12/0x1d
[<ffffffff817d7257>] sock_sendmsg+0x29/0x2e
[<ffffffff817d72cc>] sock_write_iter+0x70/0x91
[<ffffffff81199563>] __vfs_write+0x7e/0xa7
[<ffffffff811996bc>] vfs_write+0x92/0xe8
[<ffffffff811997d7>] SyS_write+0x47/0x7e
[<ffffffff81a4d517>] system_call_fastpath+0x12/0x6f
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All structures used in traffic forwarding are rcu-protected:
ipvl_addr, ipvl_dev and ipvl_port. Thus we can unhash addresses
without synchronization. We'll anyway hash it back into the same
bucket: in worst case lockless lookup will scan hash once again.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing kfree_rcu(addr, rcu);
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
They are unused after commit f631c44bbe15 ("ipvlan: Always set broadcast bit in
multicast filter").
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Earlier tricks of setting broadcast bit only when IPv4 address is added
onto interface are not good enough especially when autoconf comes in play.
Setting them on always is performance drag but now that multicast /
broadcast is not processed in fast-path; enabling broadcast will let
autoconf work correctly without affecting performance characteristics of
the device.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Processing multicast / broadcast in fast path is performance draining
and having more links means more cloning and bringing performance
down further.
Broadcast; in particular, need to be given to all the virtual links.
Earlier tricks of enabling broadcast bit for IPv4 only interfaces are not
really working since it fails autoconf. Which means enabling broadcast
for all the links if protocol specific hacks do not have to be added into
the driver.
This patch defers all (incoming as well as outgoing) multicast traffic to
a work-queue leaving only the unicast traffic in the fast-path. Now if we
need to apply any additional tricks to further reduce the impact of this
(multicast / broadcast) type of traffic, it can be implemented while
processing this work without affecting the fast-path.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't use dev->iflink anymore.
CC: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an ipvlan interface is down, its addresses are not on the hash list.
Fix checks for existence of addresses not to depend on the hash list, walk
through all interface addresses instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All accesses to ipvlan->addrs are under rtnl.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
