| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In the Meson-AXG SoC, the phy mode setting of PRG_ETH0 in the glue layer
is extended from bit[0] to bit[2:0].
There is no problem if we configure it to the RGMII 1000M PHY mode,
since the register setting is coincidentally compatible with previous one,
but for the RMII 100M PHY mode, the configuration need to be changed to
value - b100.
This patch was verified with a RTL8201F 100M ethernet PHY.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Meson8m2 SoC uses a similar (potentially even identical) register
layout as the Meson8b and GXBB SoCs for the dwmac glue.
Add a new compatible string and update the module description to
indicate support for these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The common clock framework needs access to the "clock configuration"
structs during runtime.
However, only the common clock framework should access these. Ensure
this by moving the configuration structs out of struct meson8b_dwmac,
so only meson8b_init_rgmii_tx_clk() and the common clock framework know
about these configurations.
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nothing in the dwmac-meson8b driver (except .probe itself) requires the
platform_device anymore after .probe has finished. Replace it with a
pointer to struct device since this is what the functions inside the
driver are actually accessing.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To goal of this patch is to simplify the registration of the RGMII TX
clock (and it's parent clocks). This is achieved by:
- introducing the meson8b_dwmac_register_clk helper-function to remove
code duplication when registering a single clock (this saves a few
lines since we have 4 clocks internally)
- using devm_add_action_or_reset to disable the RGMII TX clock
automatically when needed. This also allows us to re-use the standard
stmmac_pltfr_remove function.
- devm_kasprintf() and devm_kstrdup() are not used anymore to generate
the clock name (these are replaced by a variable on the stack) because
the common clock framework already uses kstrdup() internally.
No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Meson8b the only valid input clock is MPLL2. The bootloader
configures that to run at 500002394Hz which cannot be divided evenly
down to 125MHz using the m250_div clock. Currently the common clock
framework chooses a m250_div of 2 - with the internal fixed
"divide by 10" this results in a RGMII TX clock of 125001197Hz (120Hz
above the requested 125MHz).
Letting the common clock framework propagate the rate changes up to the
parent of m250_mux allows us to get the best possible clock rate. With
this patch the common clock framework calculates a rate of
very-close-to-250MHz (249999701Hz to be exact) for the MPLL2 clock
(which is the mux input). Dividing that by 2 (which is an internal,
fixed divider for the RGMII TX clock) gives us an RGMII TX clock of
124999850Hz (which is only 150Hz off the requested 125MHz, compared to
1197Hz based on the MPLL2 rate set by u-boot and the Amlogic GPL kernel
sources).
SoCs from the Meson GX series are not affected by this change because
the input clock is FCLK_DIV2 whose rate cannot be changed (which is fine
since it's running at 1GHz, so it's already a multiple of 250MHz and
125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to (but not exactly) 500MHz. The
exact rate is 500002394Hz, which is calculated in
drivers/clk/meson/clk-mpll.c using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5
The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 125MHz RGMII TX clock (on Gbit speeds,
the IP block internally divides that down to 25MHz on 100Mbit/s
connections and 2.5MHz on 10Mbit/s connections - we don't need any
special configuration for that).
Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate for the RGMII TX clock of
125001197Hz (= 125MHz plus 1197Hz), which is close-enough to 125MHz.
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 125MHz).
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tests (using an oscilloscope and an Odroid-C1 board with a RTL8211F
RGMII PHY) have shown that the PRG_ETH0 register behaves as follows:
- bit 4 is a mux to choose between two parent clocks. according to the
public S805 datasheet the only supported parent clock is MPLL2 (this
was not verified using the oscilloscope).
The public S805/S905 datasheet claims that this bit is reserved.
- bits 9:7 control a one-based divider (register value 1 means "divide
by 1", etc.) for the input clock. we call this clock the "m250_div"
clock because it's value is always supposed to be (close to) 250MHz
(see below for an explanation).
The description in the public S805/S905 datasheet is a bit cryptic,
but it comes down to "input clock = 250MHz * value" (which could also
be expressed as "250MHz = input clock / value")
- there seems to be an internal fixed divide-by-2 clock which takes the
output from the m250_div and divides it by 2. This is not unusual on
Amlogic SoCs, since the SDIO (MMC) driver also uses an internal fixed
divide-by-2 clock.
This is not documented in the public S805/S905 datasheet
- bit 10 controls a gate clock which enables or disables the RGMII TX
clock (which is an output on the MAC/SoC and an input in the PHY). we
call this the "rgmii_tx_en" clock. if this bit is set to "0" the RGMII
TX clock output is close to 0
The description for this bit in the public S805/S905 datasheet is
"Generate 25MHz clock for PHY". Based on these tests it's believed
that this is wrong, and should probably read "Generate the 125MHz
RGMII TX clock for the PHY"
- the RGMII TX clock has to be set to 125MHz - the IP block adjusts the
output (automatically) depending on the line speed (RGMII specifies
that Gbit connections use a 125MHz clock, 100Mbit/s connections use a
25MHz clock and 10Mbit/s connections use a 2.5MHz clock. only Gbit and
100Mbit/s were tested with an oscilloscope). Due to the requirement
that this clock always has to be set to 125MHz and due to the fixed
divide-by-2 parent clock this means that m250_div will always end up
with a rate of (close to) 250MHz.
- bits 6:5 are the TX delay, which is also named "clock phase" in some
of Amlogic's older GPL kernel sources.
The PHY also has an XTAL_IN pin where a 25MHz clock has to be provided.
Tests with the oscilloscope have shown that this is routed to a crystal
right next to the RTL8211F PHY. The same seems to be true on the Khadas
VIM2 (which uses a GXM SoC) board - however the 25MHz crystal is on the
other side of the PCB there.
This updates the clocks in the dwmac-meson8b driver by replacing the
"m25_div" with the "rgmii_tx_en" clock and additionally introducing a
fixed divide-by-2 clock between "m250_div" and "rgmii_tx_en".
Now we also need to set a frequency of 125MHz on the RGMII clock
(opposed to the 25MHz we set before, with that non-existing
divide-by-5-or-10 divider).
Special thanks go to Linus Lüssing for testing the various bits and
checking the results with an oscilloscope on his Odroid-C1!
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.
While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.
Fixes: 566e8251625304 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_div_table are not supposed to change at runtime.
meson8b_dwmac structure is working with const clk_div_table.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As documented in Documentation/devicetree/bindings/net/ethernet.txt,
in RGMII_ID and RGMII_TXID mode the MAC should not add a tx delay.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch we were using a hardcoded RGMII TX clock delay of
2ns (= 1/4 cycle of the 125MHz RGMII TX clock). This value works for
many boards, but unfortunately not for all (due to the way the actual
circuit is designed, sometimes because the TX delay is enabled in the
PHY, etc.). Making the TX delay on the MAC side configurable allows us
to support all possible hardware combinations.
This allows fixing a compatibility issue on some boards, where the
RTL8211F PHY is configured to generate the TX delay. We can now turn
off the TX delay in the MAC, because otherwise we would be applying the
delay twice (which results in non-working TX traffic).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by adding a new glue helper
function.
Drop the of-node reference taken in the same path also on late probe
errors (and not just on driver unbind) by moving the put from
stmmac_dvr_remove() to the new helper.
Fixes: 277323814e49 ("stmmac: add fixed-link device-tree support")
Fixes: 4613b279bee7 ("ethernet: stmicro: stmmac: add missing of_node_put
after calling of_parse_phandle")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to disable clocks before returning on late probe errors.
Fixes: 566e82516253 ("net: stmmac: add a glue driver for the Amlogic
Meson 8b / GXBB DWMAC")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet controller available in Meson8b and GXBB SoCs is a Synopsys
DesignWare MAC IP core which is already supported by the stmmac driver.
In addition to the standard stmmac driver some Meson8b / GXBB specific
registers have to be configured for the PHY clocks. These SoC specific
registers are called PRG_ETHERNET_ADDR0 and PRG_ETHERNET_ADDR1 in the
datasheet.
These registers are not backwards compatible with those on Meson 6b,
which is why a new glue driver is introduced. This worked for many
boards because the bootloader programs the PRG_ETHERNET registers
correctly. Additionally the meson6-dwmac driver only sets bit 1 of
PRG_ETHERNET_ADDR0 which (according to the datasheet) is only used
during reset.
Currently all configuration values can be determined automatically,
based on the configured phy-mode (which is mandatory for the stmmac
driver). If required the tx-delay and the mux clock (so it supports
the MPLL2 clock as well) can be made configurable in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
