| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=4053
Singed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This driver did not control NCE signal during normal operations (only
enable NCE on probing and disable NCE on removing). This patch make
NCE signal inactive on idle state.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The sam926x docs allegedly don't list an "ECC_PARITY" field, and the
header files in the upstream kernel don't have it either.
Masking with it was useless anyway, so just remove it.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This is a patch to use the hardware ECC controller of
the AT91SAM9260 and AT91SAM9263 for the AT91 nand.
On AT91 NAND, there's now a choice between ECC soft,
ECC hard or no ECC (for debug).
It has been tested on AT91SAM9263 with 8 bits large
and small page NAND.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
UBI scan takes quite a time on some systems, so it is nice
to print a message that we started attaching an MTD device.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
|
|
drivers/mtd/ar7part.c: In function ‘create_mtd_partitions’:
drivers/mtd/ar7part.c:69: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:91: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:99: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:110: warning: passing argument 4 of ‘master->read’ from incompatible pointer type
drivers/mtd/ar7part.c:111: error: ‘SQUASHFS_MAGIC’ undeclared (first use in this function)
drivers/mtd/ar7part.c:111: error: (Each undeclared identifier is reported only once
drivers/mtd/ar7part.c:111: error: for each function it appears in.)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
collie seems to contain LH28F640BF flash chips. According to
http://sharp-world.com/products/device/flash/pdf/*FUM00701*@E.pdf
(page 83) if they have 0x51 of Extended Query Table (number of hardware
partitions) set to zero, they have a single fixed partition.
This patch makes those chips work.
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
With modern systems using bus-hold instead of bus pull-up, it can
often lead to erroneous reporting of NAND devices where there are
none. Do a double probe to ensure that the result we got the first
time is repeatable, and if it is not then return that there is no
chip there.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add support to disable ECC checking for a given chip
when passed by the board via the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add support for the ECC layout to be passed via the
platform data specified by the board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This adds support for using large page NAND devices
with the S3C24XX NAND controller. This also adds the
file Documentation/arm/Samsung-S3C24XX/NAND.txt to
describe the differences.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Commit 03680b1e00d146df718c8a4eac34438566b70c85 incorrectly
was assuming S3C2410_NFCONF was being used to select the
NAND chip. Fix this error by ising the sel_reg.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
A power loss while writing can result in a page becoming unreadable.
When the device is mounted again, reading that page gives controller
errors. Upper level software like JFFS2 treat -EIO as fatal, refusing to
mount at all. That means it is necessary to treat the error as an ECC
error to allow recovery. Note that typically in this case, the
eraseblock can still be erased and rewritten i.e. it has not become a
bad block.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Minor tweaks to omap_nor ... as with most platform drivers, its probe
and remove logic can (and should!) safely vanish in most configs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This is a known erratum confirmed by Spansion. I have an errata document,
but I can't find a link to it anywhere on their site to include here.
Some of the S29GL064N chips report 64 sectors when they should report 128,
and some of S29GL032N chips report 127 sectors when they should report 63.
Note that when the chip dies are fixed by Spansion, they will still have
the same id. The fix is done in such a way that it won't affect corrected
chips.
The fixups use the extended id made available by a previous patch. Without
that, virtually all newer AMD/Spansion chips will have the same ID (0x227e)
and it's not possible to apply the fixup to the correct chips.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
AMD/Spansion use a device id of 0x7e to indicate an extended device is
present at offset 0xe and 0xf in the query data.
I've verified with Spansion that all their chips (mfr == 0x01) with an id
of 0x7e use it to indicate an extended id is present. What's more, there
are no chips with a NON-extended id that is the same as a different chip's
extended id. In other words, when the extended ID is present, one can
replace the normal id with the extended id without losing any information.
Which is what I've done.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch sets mtd->name to the platform bus ID in the plat_nand
driver, so that you can specify partitions readily with mtdparts=.
Currently it relies on nand_base filling in the name from the device,
which results in names like "NAND 256MiB 3,3V 8-bit", that you can't
use with cmdlineparts.
Signed-off-by: Hamish Moffatt <hamish@cloud.net.au>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register
Signed-off-by: Mike Hench <mhench@elutions.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"
mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.
Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.
With this patch applied fsl_elbc_nand chip will have proper name:
root@b1:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00010000 "fe000000.flash"
mtd1: 02000000 00004000 "e0600000.flash"
p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This is very simple driver, NAND is connected through localbus,
and User-Programmable Machine is doing various adjustments to
speak NAND. No special efforts needed to do read and write cycles,
though to control ALE and CLE phases, we ask UPM to generate exact
pre-programmed signals on the localbus lines.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Add support for the SST 36VF3203 flash chip. It is used on Emerson
KSI8560 board.
Signed-off-by: Andrei Dolnikov <adolnikov@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This enhances plat-ram to take a map_probes argument in
the platform_data structure which allow plat-ram to support
any direct-mapped device that MTD supports (jedec, cfi, amd ..)
A few items are also fixed:
- Don't panic if probes is 0
- Actually use the partition list that is passed in
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Untested, but shouldn't break anything... Makes MTD_XIP arch
independent. I guess this is why xip_iprefetch() was made for.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This is preliminary since:
1. It supports only _one_ chip select at the moment. As there is no
existing platforms available using two chip selects of the NAND
controller, it shall really not include code for supporting the
2nd chip select for now, as such code cannot be verified.
2. It resorts to the default and simpliest memory based badblock
table
3. Only limited types of nand flash are currently supported. Most
PXA3xx processors come with on-chip NAND flash dies, so there
isn't much flexibility for other types of NAND.
4. The NAND controller should be configured to detect the device's
ID, thus making it difficult to use nand_scan_ident() to assist
the detection process (though it's not impossible)
TODO: fix all the above limitations of cuz :-)
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Acked-By: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Return 0 partitions instead of -EINVAL on no mtdpart= argument in kernel
cmdline or missing partition info for device.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch extends the existing MAPS driver for the Nvidia CK804 chipset
(ck804xrom.c) to also work on the Nvidia MCP55 chipset. As both chipsets
are rather similar, suporting them both with the same driver is easy.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch makes the needlessly global struct rfd_ftl_tr static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch adds a proper prototype for onenand_bbt_read_oob() in
include/linux/mtd/onenand.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch makes the needlessly global cfi_staa_erase_varsize() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch makes the following needlessly global code static:
- ftl_freepart()
- struct ftl_tr
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Sparse spotted that 0 was compared to pointers.
While I was at it, I also moved the assignments out of the if's.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Every file should include the headers containing the externs for its
global functions (in this case for mtdram_init_device()).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch adds proper prototypes for nftl_{read,write}_oob() in
include/linux/mtd/nftl.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch adds proper prototypes for inftl_{read,write}_oob() in
include/linux/mtd/inftl.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
This patch adds the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Previously, a READ command was erroneously issued rather than SEQIN.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Signed-off-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
The part_probes[] should be static.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MTD NAND
platform drivers, to re-enable auto loading.
NOTE: at91_nand for some reason disallows modular builds. I'm assuming that's
just an oversight that will be fixed.
[dbrownell@users.sourceforge.net: minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable MTD mapping
platform drivers, to re-enable auto loading.
NOTE oddness with physmap ... it's a legacy driver in some configs, which
means it can't always support hotplugging. (Not that most of these mapping
drivers would often be used as modules...)
[dbrownell@users.sourceforge.net: bugfix, more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
|
