| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave().
Fixes: 166d2f6a4332 ("[Bluetooth] Add UART driver for Texas Instruments' BRF63xx chips")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch changes the kernel-doc style comment block to common comment
block. These files don't support kernel-doc style so no need to use the
kernel-doc style. Also, they cause the warning when W=1 option is used
as below.
drivers/bluetooth/hci_ll.c:518: warning: Function parameter or member 'lldev' not described in 'download_firmware'
drivers/bluetooth/btmrvl_debugfs.c:29: warning: cannot understand function prototype: 'struct btmrvl_debugfs_data '
drivers/bluetooth/btmrvl_sdio.c:36: warning: expecting prototype for Marvell BT-over-SDIO driver(). Prototype was for VERSION() instead
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When using the wl1271 Bluetooth function of am335x, it is found that the
Bluetooth module cannot respond in time after Bluetooth is enabled, and
a small delay is needed to work normally, so whether to add a small
mdelay.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
As nice as it would be to update firmware faster, that patch broke
at least two different boards, an OMAP4+WL1285 based Motorola Droid
4, as reported by Sebasian Reichel and the Logic PD i.MX6Q +
WL1837MOD.
This reverts commit a2e02f38eff84f199c8e32359eb213f81f270047.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fix some warnings and one error reported by checkpatch.pl:
- lines longer than 80 characters are wrapped
- empty lines inserted to separate variable declarations from the actual
code
- line break inserted after if (...)
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Extract the new function send_command_from_firmware from
download_firmware, which helps with the readability of the switch
statement. This way the code is less deeply nested and also no longer
exceeds the 80 character limit.
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Uploading the firmware needs quite a few seconds if done at 115200 kbps. So set
the operational frequency, usually 3 MHz, before uploading the firmware.
I have successfully tested this with a wl1837mod.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 59 temple place suite 330 boston ma 02111
1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 136 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.384967451@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make hci_uart_register_device() and hci_uart_unregister_device() call
serdev_device_close()/open() themselves instead of relying on the various
hci_uart drivers to do this for them.
Besides reducing code complexity, this also ensures correct error checking
of serdev_device_open(), which was missing in a few drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The HCILL or eHCILL protocol from TI is actually an H:4 protocol with a
few extra events and thus can also use the h4_recv_buf helper. Instead
of open coding the same funtionality add the extra events to the packet
description table and use h4_recv_buf.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The struct hcill_cmd to create an skb with a single u8 is pointless. So
just use skb_put_u8 instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
download_firmware() is never called from atomic context.
It is only called by ll_setup() that is called only via function pointer
"->setup" used in hci_uart_setup() in drivers/bluetooth/hci_serdev.c and
drivers/bluetooth/hci_ldisc.c. hci_uart_setup() is called only
via function pointer "->setup" used in hci_dev_do_open()
in net/bluetooth/hci_core.c.
All of the above functions do not enter atomic context.
Besides, ll_setup() calls msleep() and hci_dev_do_open calls mutex_lock().
So it indicates that all the above functions call functions that can sleep.
Despite never getting called from atomic context, download_firmware()
calls mdelay() for busy wait.
That is not necessary and can be replaced with msleep to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds the "ti,cc2560" compatible string for a TI CC2560 chip.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds an optional nvmem consumer to get a BD address from an external
source. The BD address is then set in the Bluetooth chip after the
firmware has been loaded.
This has been tested working with a TI CC2560A chip (in a LEGO MINDSTORMS
EV3).
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds support for setting the public address on Texas Instruments
Bluetooth chips using a vendor-specific command.
This has been tested on a CC2560A chip. The TI wiki also indicates that
this command should work on TI WL17xx/WL18xx Bluetooth chips.
During review, there was some question as to the correctness of the byte
swapping since TI's documentation is not clear on this matter. This can
be tested with the btmgmt utility from bluez. The adapter must be powered
off to change the address. If the baswap() is omitted, address is reversed.
In case there is a issue in the future, here is the output of btmon during
the command `btmgmt public-addr 00:11:22:33:44:55`:
Bluetooth monitor ver 5.43
= Note: Linux version 4.15.0-rc2-08561-gcb132a1-dirty (armv5tejl) 0.707043
= Note: Bluetooth subsystem version 2.22 0.707091
= New Index: 00:17:E7:BD:1C:8E (Primary,UART,hci0) [hci0] 0.707106
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0002} 0.707124
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.707137
@ MGMT Open: btmon (privileged) version 1.14 {0x0003} 0.707540
@ MGMT Command: Set Public Address (0x0039) plen 6 {0x0002} [hci0] 11.167991
Address: 00:11:22:33:44:55 (CIMSYS Inc)
@ MGMT Event: Command Complete (0x0001) plen 7 {0x0002} [hci0] 11.175681
Set Public Address (0x0039) plen 4
Status: Success (0x00)
Missing options: 0x00000000
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0003} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0002} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0001} [hci0] 11.175757
= Open Index: 00:17:E7:BD:1C:8E [hci0] 11.176807
< HCI Command: Vendor (0x3f|0x0006) plen 6 [hci0] 11.176975
00 11 22 33 44 55 .."3DU
> HCI Event: Command Complete (0x0e) plen 4 [hci0] 11.188260
Vendor (0x3f|0x0006) ncmd 1
Status: Success (0x00)
...
< HCI Command: Read Local Version Info.. (0x04|0x0001) plen 0 [hci0] 11.189859
> HCI Event: Command Complete (0x0e) plen 12 [hci0] 11.190732
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 2.1 (0x04) - Revision 0 (0x0000)
LMP version: Bluetooth 2.1 (0x04) - Subversion 6431 (0x191f)
Manufacturer: Texas Instruments Inc. (13)
< HCI Command: Read BD ADDR (0x04|0x0009) plen 0 [hci0] 11.191027
> HCI Event: Command Complete (0x0e) plen 10 [hci0] 11.192101
Read BD ADDR (0x04|0x0009) ncmd 1
Status: Success (0x00)
Address: 00:11:22:33:44:55 (CIMSYS Inc)
...
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).
We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().
Also changed the comment to be more informative while we are touching this
code.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The bt_* printk macros include a \n already, so we don't need extra ones
here.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
In this particular case, notice that I replaced the
"deliberate fall-through..." comment with a "fall through"
comment, which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixed alignment of all block comments.
Found using checkpatch
Signed-off-by: Derek Robson <robsonde@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Convert hci_ll to use hci_uart_unregister_device().
This simplifies the _remove() handler as well as fixes a
potential race condition on unload.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabor.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to manage the external clock provided to the WiLink combo chip
as it's needed for any of the transport interfaces.
To avoid breaking platforms not yet specifying the external clock, we make
it optional. In case the clock is successfully fetched during ->probe(),
let's manage it via the ->open|close() callbacks, to make sure the device
get properly powered on/off.
Fixes: ea452678734e ("arm64: dts: hikey: Fix WiFi support")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add compatible values for WiLink chips from 128x and 180x series.
Also the DT binding already contained compatible values for the 127x
series, but the driver did not. This brings the list on par with
the list from wlcore (the wifi driver).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When __hci_cmd_sync() fails, download_firmware() should also fail, and
the same error value should be returned as PTR_ERR(skb).
Without this fix, download_firmware() will return a success when it actually
failed in __hci_cmd_sync().
Fixes: 371805522f87 ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Avoid NULL pointer dereference occurring due to freeing
skb containing an error pointer. It can easily be triggered
by using the driver with broken uart (i.e. due to misconfigured
pinmuxing).
Fixes: 371805522f87 ("bluetooth: hci_uart: add LL protocol serdev driver support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Turns out that the LL protocol and the TI-ST are the same thing AFAICT.
The TI-ST adds firmware loading, GPIO control, and shared access for
NFC, FM radio, etc. For now, we're only implementing what is needed for
BT. This mirrors other drivers like BCM and Intel, but uses the new
serdev bus.
The firmware loading is greatly simplified by using existing
infrastructure to send commands. It may be a bit slower than the
original code using synchronous functions, but the real bottleneck is
likely doing firmware load at 115.2kbps.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The init function for each HCI UART protocol prints the same on success
and failure. This information is so generic, remove it and let the main
HCI UART handling print it instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This adds an extra name field to the hci_uart_proto struct that provides
a simple way of adding a string identifier to the protocol.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The usage of struct hci_uart_proto should always be const. Change the
function headers and individual protocol drivers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The TTY layer provides its data pointers as const, but the HCI UART
callbacks expect them as general data pointers. This is of course
wrong and instead of casting them, just fix the individual drivers
to actually take a const data pointer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.
This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
To avoid casting skb->dev into hdev, just let the drivers provide
the hdev directly when calling hci_recv_frame() function.
This patch also fixes up all drivers to provide the hdev.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Let the compiler chooses what is best.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The uart_proto open() callback is not called in atomic context so we can safely
sleep here. The caller hci_uart_set_proto() in hci_ldisc.c is an ioctl() handler
and therefore can sleep.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Those marks are useful to save space in the binary and in the memory.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Use the __packed annotation instead of the __attribute__((packed)).
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Set the proper error(ENOMEM), instead of just return 0.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Remove some pointless conditionals before kfree_skb().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In the (rare) event of simultaneous mutual wake up requests,
do send the chip an explicit wake-up ack. This is required
for Texas Instruments's BRF6350 chip.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Texas Instruments' HCI Low Level (HCILL) Bluetooth
protocol, which is a power management extension to H4. The HCILL is
widely used by TI's BRF63xx Bluetooth chips.
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
