| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We need the USB fixes in here as well to build off of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add a forgotten CPU vendor check in the AMD microcode post-loading
callback so that the callback runs only on AMD
- Make sure SEV-ES protocol negotiation happens only once and on the
BSP
* tag 'x86_urgent_for_v6.7_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Check vendor in the AMD microcode callback
x86/sev: Fix kernel crash due to late update to read-only ghcb_version
|
|
Pull kvm fixes from Paolo Bonzini:
"Generic:
- Set .owner for various KVM file_operations so that files refcount
the KVM module until KVM is done executing _all_ code, including
the last few instructions of kvm_put_kvm(). And then revert the
misguided attempt to rely on "struct kvm" refcounts to pin
KVM-the-module.
ARM:
- Do not redo the mapping of vLPIs, if they have already been mapped
s390:
- Do not leave bits behind in PTEs
- Properly catch page invalidations that affect the prefix of a
nested guest
x86:
- When checking if a _running_ vCPU is "in-kernel", i.e. running at
CPL0, get the CPL directly instead of relying on
preempted_in_kernel (which is valid if and only if the vCPU was
preempted, i.e. NOT running).
- Fix a benign "return void" that was recently introduced.
Selftests:
- Makefile tweak for dependency generation
- '-Wformat' fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Update EFER software model on CR0 trap for SEV-ES
KVM: selftests: add -MP to CFLAGS
KVM: selftests: Actually print out magic token in NX hugepages skip message
KVM: x86: Remove 'return void' expression for 'void function'
Revert "KVM: Prevent module exit until all VMs are freed"
KVM: Set file_operations.owner appropriately for all such structures
KVM: x86: Get CPL directly when checking if loaded vCPU is in kernel mode
KVM: arm64: GICv4: Do not perform a map to a mapped vLPI
KVM: s390/mm: Properly reset no-dat
KVM: s390: vsie: fix wrong VIR 37 when MSO is used
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
- Fix stack teardown in ftrace_no_trace, seen as crashes doing CPU
hotplug while ftrace is active.
Thanks to Naveen N Rao.
* tag 'powerpc-6.7-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ftrace: Fix stack teardown in ftrace_no_trace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Preserve syscall nr across execve(), slightly clean up drdtime(), fix
the Clang built zboot kernel, fix a stack unwinder bug and several bpf
jit bugs"
* tag 'loongarch-fixes-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: BPF: Fix unconditional bswap instructions
LoongArch: BPF: Fix sign-extension mov instructions
LoongArch: BPF: Don't sign extend function return value
LoongArch: BPF: Don't sign extend memory load operand
LoongArch: Preserve syscall nr across execve()
LoongArch: Set unwind stack type to unknown rather than set error flag
LoongArch: Slightly clean up drdtime()
LoongArch: Apply dynamic relocations for LLD
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- Fixes for broken Loongson firmware
- Fix lockdep splat
- Fix FPU states when creating kernel threads
* tag 'mips-fixes_6.7_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kernel: Clear FPU states when setting up kernel threads
MIPS: Loongson64: Handle more memory types passed from firmware
MIPS: Loongson64: Enable DMA noncoherent support
MIPS: Loongson64: Reserve vgabios memory on boot
mips/smp: Call rcutree_report_cpu_starting() earlier
|
|
We can see that "bswap32: Takes an unsigned 32-bit number in either big-
or little-endian format and returns the equivalent number with the same
bit width but opposite endianness" in BPF Instruction Set Specification,
so it should clear the upper 32 bits in "case 32:" for both BPF_ALU and
BPF_ALU64.
[root@linux fedora]# echo 1 > /proc/sys/net/core/bpf_jit_enable
[root@linux fedora]# modprobe test_bpf
Before:
test_bpf: #313 BSWAP 32: 0x0123456789abcdef -> 0xefcdab89 jited:1 ret 1460850314 != -271733879 (0x5712ce8a != 0xefcdab89)FAIL (1 times)
test_bpf: #317 BSWAP 32: 0xfedcba9876543210 -> 0x10325476 jited:1 ret -1460850316 != 271733878 (0xa8ed3174 != 0x10325476)FAIL (1 times)
After:
test_bpf: #313 BSWAP 32: 0x0123456789abcdef -> 0xefcdab89 jited:1 4 PASS
test_bpf: #317 BSWAP 32: 0xfedcba9876543210 -> 0x10325476 jited:1 4 PASS
Fixes: 4ebf9216e7df ("LoongArch: BPF: Support unconditional bswap instructions")
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
We can see that "Short form of movsx, dst_reg = (s8,s16,s32)src_reg" in
include/linux/filter.h, additionally, for BPF_ALU64 the value of the
destination register is unchanged whereas for BPF_ALU the upper 32 bits
of the destination register are zeroed, so it should clear the upper 32
bits for BPF_ALU.
[root@linux fedora]# echo 1 > /proc/sys/net/core/bpf_jit_enable
[root@linux fedora]# modprobe test_bpf
Before:
test_bpf: #81 ALU_MOVSX | BPF_B jited:1 ret 2 != 1 (0x2 != 0x1)FAIL (1 times)
test_bpf: #82 ALU_MOVSX | BPF_H jited:1 ret 2 != 1 (0x2 != 0x1)FAIL (1 times)
After:
test_bpf: #81 ALU_MOVSX | BPF_B jited:1 6 PASS
test_bpf: #82 ALU_MOVSX | BPF_H jited:1 6 PASS
By the way, the bpf selftest case "./test_progs -t verifier_movsx" can
also be fixed with this patch.
Fixes: f48012f16150 ("LoongArch: BPF: Support sign-extension mov instructions")
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The `cls_redirect` test triggers a kernel panic like:
# ./test_progs -t cls_redirect
Can't find bpf_testmod.ko kernel module: -2
WARNING! Selftests relying on bpf_testmod.ko will be skipped.
[ 30.938489] CPU 3 Unable to handle kernel paging request at virtual address fffffffffd814de0, era == ffff800002009fb8, ra == ffff800002009f9c
[ 30.939331] Oops[#1]:
[ 30.939513] CPU: 3 PID: 1260 Comm: test_progs Not tainted 6.7.0-rc2-loong-devel-g2f56bb0d2327 #35 a896aca3f4164f09cc346f89f2e09832e07be5f6
[ 30.939732] Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
[ 30.939901] pc ffff800002009fb8 ra ffff800002009f9c tp 9000000104da4000 sp 9000000104da7ab0
[ 30.940038] a0 fffffffffd814de0 a1 9000000104da7a68 a2 0000000000000000 a3 9000000104da7c10
[ 30.940183] a4 9000000104da7c14 a5 0000000000000002 a6 0000000000000021 a7 00005555904d7f90
[ 30.940321] t0 0000000000000110 t1 0000000000000000 t2 fffffffffd814de0 t3 0004c4b400000000
[ 30.940456] t4 ffffffffffffffff t5 00000000c3f63600 t6 0000000000000000 t7 0000000000000000
[ 30.940590] t8 000000000006d803 u0 0000000000000020 s9 9000000104da7b10 s0 900000010504c200
[ 30.940727] s1 fffffffffd814de0 s2 900000010504c200 s3 9000000104da7c10 s4 9000000104da7ad0
[ 30.940866] s5 0000000000000000 s6 90000000030e65bc s7 9000000104da7b44 s8 90000000044f6fc0
[ 30.941015] ra: ffff800002009f9c bpf_prog_846803e5ae81417f_cls_redirect+0xa0/0x590
[ 30.941535] ERA: ffff800002009fb8 bpf_prog_846803e5ae81417f_cls_redirect+0xbc/0x590
[ 30.941696] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[ 30.942224] PRMD: 00000004 (PPLV0 +PIE -PWE)
[ 30.942330] EUEN: 00000003 (+FPE +SXE -ASXE -BTE)
[ 30.942453] ECFG: 00071c1c (LIE=2-4,10-12 VS=7)
[ 30.942612] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[ 30.942764] BADV: fffffffffd814de0
[ 30.942854] PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
[ 30.942974] Modules linked in:
[ 30.943078] Process test_progs (pid: 1260, threadinfo=00000000ce303226, task=000000007d10bb76)
[ 30.943306] Stack : 900000010a064000 90000000044f6fc0 9000000104da7b48 0000000000000000
[ 30.943495] 0000000000000000 9000000104da7c14 9000000104da7c10 900000010504c200
[ 30.943626] 0000000000000001 ffff80001b88c000 9000000104da7b70 90000000030e6668
[ 30.943785] 0000000000000000 9000000104da7b58 ffff80001b88c048 9000000003d05000
[ 30.943936] 900000000303ac88 0000000000000000 0000000000000000 9000000104da7b70
[ 30.944091] 0000000000000000 0000000000000001 0000000731eeab00 0000000000000000
[ 30.944245] ffff80001b88c000 0000000000000000 0000000000000000 54b99959429f83b8
[ 30.944402] ffff80001b88c000 90000000044f6fc0 9000000101d70000 ffff80001b88c000
[ 30.944538] 000000000000005a 900000010504c200 900000010a064000 900000010a067000
[ 30.944697] 9000000104da7d88 0000000000000000 9000000003d05000 90000000030e794c
[ 30.944852] ...
[ 30.944924] Call Trace:
[ 30.945120] [<ffff800002009fb8>] bpf_prog_846803e5ae81417f_cls_redirect+0xbc/0x590
[ 30.945650] [<90000000030e6668>] bpf_test_run+0x1ec/0x2f8
[ 30.945958] [<90000000030e794c>] bpf_prog_test_run_skb+0x31c/0x684
[ 30.946065] [<90000000026d4f68>] __sys_bpf+0x678/0x2724
[ 30.946159] [<90000000026d7288>] sys_bpf+0x20/0x2c
[ 30.946253] [<90000000032dd224>] do_syscall+0x7c/0x94
[ 30.946343] [<9000000002541c5c>] handle_syscall+0xbc/0x158
[ 30.946492]
[ 30.946549] Code: 0015030e 5c0009c0 5001d000 <28c00304> 02c00484 29c00304 00150009 2a42d2e4 0280200d
[ 30.946793]
[ 30.946971] ---[ end trace 0000000000000000 ]---
[ 32.093225] Kernel panic - not syncing: Fatal exception in interrupt
[ 32.093526] Kernel relocated by 0x2320000
[ 32.093630] .text @ 0x9000000002520000
[ 32.093725] .data @ 0x9000000003400000
[ 32.093792] .bss @ 0x9000000004413200
[ 34.971998] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---
This is because we signed-extend function return values. When subprog
mode is enabled, we have:
cls_redirect()
-> get_global_metrics() returns pcpu ptr 0xfffffefffc00b480
The pointer returned is later signed-extended to 0xfffffffffc00b480 at
`BPF_JMP | BPF_EXIT`. During BPF prog run, this triggers unhandled page
fault and a kernel panic.
Drop the unnecessary signed-extension on return values like other
architectures do.
With this change, we have:
# ./test_progs -t cls_redirect
Can't find bpf_testmod.ko kernel module: -2
WARNING! Selftests relying on bpf_testmod.ko will be skipped.
#51/1 cls_redirect/cls_redirect_inlined:OK
#51/2 cls_redirect/IPv4 TCP accept unknown (no hops, flags: SYN):OK
#51/3 cls_redirect/IPv6 TCP accept unknown (no hops, flags: SYN):OK
#51/4 cls_redirect/IPv4 TCP accept unknown (no hops, flags: ACK):OK
#51/5 cls_redirect/IPv6 TCP accept unknown (no hops, flags: ACK):OK
#51/6 cls_redirect/IPv4 TCP forward unknown (one hop, flags: ACK):OK
#51/7 cls_redirect/IPv6 TCP forward unknown (one hop, flags: ACK):OK
#51/8 cls_redirect/IPv4 TCP accept known (one hop, flags: ACK):OK
#51/9 cls_redirect/IPv6 TCP accept known (one hop, flags: ACK):OK
#51/10 cls_redirect/IPv4 UDP accept unknown (no hops, flags: none):OK
#51/11 cls_redirect/IPv6 UDP accept unknown (no hops, flags: none):OK
#51/12 cls_redirect/IPv4 UDP forward unknown (one hop, flags: none):OK
#51/13 cls_redirect/IPv6 UDP forward unknown (one hop, flags: none):OK
#51/14 cls_redirect/IPv4 UDP accept known (one hop, flags: none):OK
#51/15 cls_redirect/IPv6 UDP accept known (one hop, flags: none):OK
#51/16 cls_redirect/cls_redirect_subprogs:OK
#51/17 cls_redirect/IPv4 TCP accept unknown (no hops, flags: SYN):OK
#51/18 cls_redirect/IPv6 TCP accept unknown (no hops, flags: SYN):OK
#51/19 cls_redirect/IPv4 TCP accept unknown (no hops, flags: ACK):OK
#51/20 cls_redirect/IPv6 TCP accept unknown (no hops, flags: ACK):OK
#51/21 cls_redirect/IPv4 TCP forward unknown (one hop, flags: ACK):OK
#51/22 cls_redirect/IPv6 TCP forward unknown (one hop, flags: ACK):OK
#51/23 cls_redirect/IPv4 TCP accept known (one hop, flags: ACK):OK
#51/24 cls_redirect/IPv6 TCP accept known (one hop, flags: ACK):OK
#51/25 cls_redirect/IPv4 UDP accept unknown (no hops, flags: none):OK
#51/26 cls_redirect/IPv6 UDP accept unknown (no hops, flags: none):OK
#51/27 cls_redirect/IPv4 UDP forward unknown (one hop, flags: none):OK
#51/28 cls_redirect/IPv6 UDP forward unknown (one hop, flags: none):OK
#51/29 cls_redirect/IPv4 UDP accept known (one hop, flags: none):OK
#51/30 cls_redirect/IPv6 UDP accept known (one hop, flags: none):OK
#51/31 cls_redirect/cls_redirect_dynptr:OK
#51/32 cls_redirect/IPv4 TCP accept unknown (no hops, flags: SYN):OK
#51/33 cls_redirect/IPv6 TCP accept unknown (no hops, flags: SYN):OK
#51/34 cls_redirect/IPv4 TCP accept unknown (no hops, flags: ACK):OK
#51/35 cls_redirect/IPv6 TCP accept unknown (no hops, flags: ACK):OK
#51/36 cls_redirect/IPv4 TCP forward unknown (one hop, flags: ACK):OK
#51/37 cls_redirect/IPv6 TCP forward unknown (one hop, flags: ACK):OK
#51/38 cls_redirect/IPv4 TCP accept known (one hop, flags: ACK):OK
#51/39 cls_redirect/IPv6 TCP accept known (one hop, flags: ACK):OK
#51/40 cls_redirect/IPv4 UDP accept unknown (no hops, flags: none):OK
#51/41 cls_redirect/IPv6 UDP accept unknown (no hops, flags: none):OK
#51/42 cls_redirect/IPv4 UDP forward unknown (one hop, flags: none):OK
#51/43 cls_redirect/IPv6 UDP forward unknown (one hop, flags: none):OK
#51/44 cls_redirect/IPv4 UDP accept known (one hop, flags: none):OK
#51/45 cls_redirect/IPv6 UDP accept known (one hop, flags: none):OK
#51 cls_redirect:OK
Summary: 1/45 PASSED, 0 SKIPPED, 0 FAILED
Fixes: 5dc615520c4d ("LoongArch: Add BPF JIT support")
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
The `cgrp_local_storage` test triggers a kernel panic like:
# ./test_progs -t cgrp_local_storage
Can't find bpf_testmod.ko kernel module: -2
WARNING! Selftests relying on bpf_testmod.ko will be skipped.
[ 550.930632] CPU 1 Unable to handle kernel paging request at virtual address 0000000000000080, era == ffff80000200be34, ra == ffff80000200be00
[ 550.931781] Oops[#1]:
[ 550.931966] CPU: 1 PID: 1303 Comm: test_progs Not tainted 6.7.0-rc2-loong-devel-g2f56bb0d2327 #35 a896aca3f4164f09cc346f89f2e09832e07be5f6
[ 550.932215] Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
[ 550.932403] pc ffff80000200be34 ra ffff80000200be00 tp 9000000108350000 sp 9000000108353dc0
[ 550.932545] a0 0000000000000000 a1 0000000000000517 a2 0000000000000118 a3 00007ffffbb15558
[ 550.932682] a4 00007ffffbb15620 a5 90000001004e7700 a6 0000000000000021 a7 0000000000000118
[ 550.932824] t0 ffff80000200bdc0 t1 0000000000000517 t2 0000000000000517 t3 00007ffff1c06ee0
[ 550.932961] t4 0000555578ae04d0 t5 fffffffffffffff8 t6 0000000000000004 t7 0000000000000020
[ 550.933097] t8 0000000000000040 u0 00000000000007b8 s9 9000000108353e00 s0 90000001004e7700
[ 550.933241] s1 9000000004005000 s2 0000000000000001 s3 0000000000000000 s4 0000555555eb2ec8
[ 550.933379] s5 00007ffffbb15bb8 s6 00007ffff1dafd60 s7 000055555663f610 s8 00007ffff1db0050
[ 550.933520] ra: ffff80000200be00 bpf_prog_98f1b9e767be2a84_on_enter+0x40/0x200
[ 550.933911] ERA: ffff80000200be34 bpf_prog_98f1b9e767be2a84_on_enter+0x74/0x200
[ 550.934105] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[ 550.934596] PRMD: 00000004 (PPLV0 +PIE -PWE)
[ 550.934712] EUEN: 00000003 (+FPE +SXE -ASXE -BTE)
[ 550.934836] ECFG: 00071c1c (LIE=2-4,10-12 VS=7)
[ 550.934976] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[ 550.935097] BADV: 0000000000000080
[ 550.935181] PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
[ 550.935291] Modules linked in:
[ 550.935391] Process test_progs (pid: 1303, threadinfo=000000006c3b1c41, task=0000000061f84a55)
[ 550.935643] Stack : 00007ffffbb15bb8 0000555555eb2ec8 0000000000000000 0000000000000001
[ 550.935844] 9000000004005000 ffff80001b864000 00007ffffbb15450 90000000029aa034
[ 550.935990] 0000000000000000 9000000108353ec0 0000000000000118 d07d9dfb09721a09
[ 550.936175] 0000000000000001 0000000000000000 9000000108353ec0 0000000000000118
[ 550.936314] 9000000101d46ad0 900000000290abf0 000055555663f610 0000000000000000
[ 550.936479] 0000000000000003 9000000108353ec0 00007ffffbb15450 90000000029d7288
[ 550.936635] 00007ffff1dafd60 000055555663f610 0000000000000000 0000000000000003
[ 550.936779] 9000000108353ec0 90000000035dd1f0 00007ffff1dafd58 9000000002841c5c
[ 550.936939] 0000000000000119 0000555555eea5a8 00007ffff1d78780 00007ffffbb153e0
[ 550.937083] ffffffffffffffda 00007ffffbb15518 0000000000000040 00007ffffbb15558
[ 550.937224] ...
[ 550.937299] Call Trace:
[ 550.937521] [<ffff80000200be34>] bpf_prog_98f1b9e767be2a84_on_enter+0x74/0x200
[ 550.937910] [<90000000029aa034>] bpf_trace_run2+0x90/0x154
[ 550.938105] [<900000000290abf0>] syscall_trace_enter.isra.0+0x1cc/0x200
[ 550.938224] [<90000000035dd1f0>] do_syscall+0x48/0x94
[ 550.938319] [<9000000002841c5c>] handle_syscall+0xbc/0x158
[ 550.938477]
[ 550.938607] Code: 580009ae 50016000 262402e4 <28c20085> 14092084 03a00084 16000024 03240084 00150006
[ 550.938851]
[ 550.939021] ---[ end trace 0000000000000000 ]---
Further investigation shows that this panic is triggered by memory
load operations:
ptr = bpf_cgrp_storage_get(&map_a, task->cgroups->dfl_cgrp, 0,
BPF_LOCAL_STORAGE_GET_F_CREATE);
The expression `task->cgroups->dfl_cgrp` involves two memory load.
Since the field offset fits in imm12 or imm14, we use ldd or ldptrd
instructions. But both instructions have the side effect that it will
signed-extended the imm operand. Finally, we got the wrong addresses
and panics is inevitable.
Use a generic ldxd instruction to avoid this kind of issues.
With this change, we have:
# ./test_progs -t cgrp_local_storage
Can't find bpf_testmod.ko kernel module: -2
WARNING! Selftests relying on bpf_testmod.ko will be skipped.
test_cgrp_local_storage:PASS:join_cgroup /cgrp_local_storage 0 nsec
#48/1 cgrp_local_storage/tp_btf:OK
test_attach_cgroup:PASS:skel_open 0 nsec
test_attach_cgroup:PASS:prog_attach 0 nsec
test_attach_cgroup:PASS:prog_attach 0 nsec
libbpf: prog 'update_cookie_tracing': failed to attach: ERROR: strerror_r(-524)=22
test_attach_cgroup:FAIL:prog_attach unexpected error: -524
#48/2 cgrp_local_storage/attach_cgroup:FAIL
test_recursion:PASS:skel_open_and_load 0 nsec
libbpf: prog 'on_lookup': failed to attach: ERROR: strerror_r(-524)=22
libbpf: prog 'on_lookup': failed to auto-attach: -524
test_recursion:FAIL:skel_attach unexpected error: -524 (errno 524)
#48/3 cgrp_local_storage/recursion:FAIL
#48/4 cgrp_local_storage/negative:OK
#48/5 cgrp_local_storage/cgroup_iter_sleepable:OK
test_yes_rcu_lock:PASS:skel_open 0 nsec
test_yes_rcu_lock:PASS:skel_load 0 nsec
libbpf: prog 'yes_rcu_lock': failed to attach: ERROR: strerror_r(-524)=22
libbpf: prog 'yes_rcu_lock': failed to auto-attach: -524
test_yes_rcu_lock:FAIL:skel_attach unexpected error: -524 (errno 524)
#48/6 cgrp_local_storage/yes_rcu_lock:FAIL
#48/7 cgrp_local_storage/no_rcu_lock:OK
#48 cgrp_local_storage:FAIL
All error logs:
test_cgrp_local_storage:PASS:join_cgroup /cgrp_local_storage 0 nsec
test_attach_cgroup:PASS:skel_open 0 nsec
test_attach_cgroup:PASS:prog_attach 0 nsec
test_attach_cgroup:PASS:prog_attach 0 nsec
libbpf: prog 'update_cookie_tracing': failed to attach: ERROR: strerror_r(-524)=22
test_attach_cgroup:FAIL:prog_attach unexpected error: -524
#48/2 cgrp_local_storage/attach_cgroup:FAIL
test_recursion:PASS:skel_open_and_load 0 nsec
libbpf: prog 'on_lookup': failed to attach: ERROR: strerror_r(-524)=22
libbpf: prog 'on_lookup': failed to auto-attach: -524
test_recursion:FAIL:skel_attach unexpected error: -524 (errno 524)
#48/3 cgrp_local_storage/recursion:FAIL
test_yes_rcu_lock:PASS:skel_open 0 nsec
test_yes_rcu_lock:PASS:skel_load 0 nsec
libbpf: prog 'yes_rcu_lock': failed to attach: ERROR: strerror_r(-524)=22
libbpf: prog 'yes_rcu_lock': failed to auto-attach: -524
test_yes_rcu_lock:FAIL:skel_attach unexpected error: -524 (errno 524)
#48/6 cgrp_local_storage/yes_rcu_lock:FAIL
#48 cgrp_local_storage:FAIL
Summary: 0/4 PASSED, 0 SKIPPED, 1 FAILED
No panics any more (The test still failed because lack of BPF trampoline
which I am actively working on).
Fixes: 5dc615520c4d ("LoongArch: Add BPF JIT support")
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Currently, we store syscall nr in pt_regs::regs[11] and syscall execve()
accidentally overrides it during its execution:
sys_execve()
-> do_execve()
-> do_execveat_common()
-> bprm_execve()
-> exec_binprm()
-> search_binary_handler()
-> load_elf_binary()
-> ELF_PLAT_INIT()
ELF_PLAT_INIT() reset regs[11] to 0, so in syscall_exit_to_user_mode()
we later get a wrong syscall nr. This breaks tools like execsnoop since
it relies on execve() tracepoints.
Skip pt_regs::regs[11] reset in ELF_PLAT_INIT() to fix the issue.
Signed-off-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
During unwinding, unwind_done() is used as an end condition. Normally it
unwind to the user stack and then set the stack type to unknown, which
is a normal exit. When something unexpected happens in unwind process
and we cannot unwind anymore, we should set the error flag, and also set
the stack type to unknown to indicate that the unwind process can not
continue. The error flag emphasizes that the unwind process produce an
unexpected error. There is no unexpected things when we unwind the PT_REGS
in the top of IRQ stack and find out that is an user mode PT_REGS. Thus,
we should not set error flag and just set stack type to unknown.
Reported-by: Hengqi Chen <hengqi.chen@gmail.com>
Acked-by: Hengqi Chen <hengqi.chen@gmail.com>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
As we are just discarding the stable clock ID, simply write it into
$zero instead of allocating a temporary register.
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
For the following assembly code:
.text
.global func
func:
nop
.data
var:
.dword func
When linked with `-pie`, GNU LD populates the `var` variable with the
pre-relocated value of `func`. However, LLVM LLD does not exhibit the
same behavior. This issue also arises with the `kernel_entry` in arch/
loongarch/kernel/head.S:
_head:
.word MZ_MAGIC /* "MZ", MS-DOS header */
.org 0x8
.dword kernel_entry /* Kernel entry point */
The correct kernel entry from the MS-DOS header is crucial for jumping
to vmlinux from zboot. This necessity is why the compressed relocatable
kernel compiled by Clang encounters difficulties in booting.
To address this problem, it is proposed to apply dynamic relocations to
place with `--apply-dynamic-relocs`.
Link: https://github.com/ClangBuiltLinux/linux/issues/1962
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
In general, activating long mode involves setting the EFER_LME bit in
the EFER register and then enabling the X86_CR0_PG bit in the CR0
register. At this point, the EFER_LMA bit will be set automatically by
hardware.
In the case of SVM/SEV guests where writes to CR0 are intercepted, it's
necessary for the host to set EFER_LMA on behalf of the guest since
hardware does not see the actual CR0 write.
In the case of SEV-ES guests where writes to CR0 are trapped instead of
intercepted, the hardware *does* see/record the write to CR0 before
exiting and passing the value on to the host, so as part of enabling
SEV-ES support commit f1c6366e3043 ("KVM: SVM: Add required changes to
support intercepts under SEV-ES") dropped special handling of the
EFER_LMA bit with the understanding that it would be set automatically.
However, since the guest never explicitly sets the EFER_LMA bit, the
host never becomes aware that it has been set. This becomes problematic
when userspace tries to get/set the EFER values via
KVM_GET_SREGS/KVM_SET_SREGS, since the EFER contents tracked by the host
will be missing the EFER_LMA bit, and when userspace attempts to pass
the EFER value back via KVM_SET_SREGS it will fail a sanity check that
asserts that EFER_LMA should always be set when X86_CR0_PG and EFER_LME
are set.
Fix this by always inferring the value of EFER_LMA based on X86_CR0_PG
and EFER_LME, regardless of whether or not SEV-ES is enabled.
Fixes: f1c6366e3043 ("KVM: SVM: Add required changes to support intercepts under SEV-ES")
Reported-by: Peter Gonda <pgonda@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210507165947.2502412-2-seanjc@google.com>
[A two year old patch that was revived after we noticed the failure in
KVM_SET_SREGS and a similar patch was posted by Michael Roth. This is
Sean's patch, but with Michael's more complete commit message. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm-master
KVM fixes for 6.7-rcN:
- When checking if a _running_ vCPU is "in-kernel", i.e. running at CPL0,
get the CPL directly instead of relying on preempted_in_kernel, which
is valid if and only if the vCPU was preempted, i.e. NOT running.
- Set .owner for various KVM file_operations so that files refcount the
KVM module until KVM is done executing _all_ code, including the last
few instructions of kvm_put_kvm(). And then revert the misguided
attempt to rely on "struct kvm" refcounts to pin KVM-the-module.
- Fix a benign "return void" that was recently introduced.
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
Two small but important bugfixes.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/arm64 fixes for 6.7, take #1
- Avoid mapping vLPIs that have already been mapped
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A pair of fixes to the new module load-time relocation code
- A fix for hwprobe overflowing on rv32
- A fix for to correctly decode C.SWSP and C.SDSP, which manifests in
misaligned access handling
- A fix for a boot-time shadow call stack initialization ordering issue
- A fix for Andes' errata probing, which was calling
riscv_noncoherent_supported() too late in the boot process and
triggering an oops
* tag 'riscv-for-linus-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: errata: andes: Probe for IOCP only once in boot stage
riscv: Fix SMP when shadow call stacks are enabled
dt-bindings: perf: riscv,pmu: drop unneeded quotes
riscv: fix misaligned access handling of C.SWSP and C.SDSP
RISC-V: hwprobe: Always use u64 for extension bits
Support rv32 ULEB128 test
riscv: Correct type casting in module loading
riscv: Safely remove entries from relocation list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes are devicetree fixes for NXP, Mediatek, Rockchips
Arm machines as well as Microchip RISC-V, and most of these address
build-time warnings for spec violations and other minor issues. One of
the Mediatek warnings was enabled by default and prevented a clean
build.
The ones that address serious runtime issues are all on the i.MX
platform:
- a boot time panic on imx8qm
- USB hanging under load on imx8
- regressions on the imx93 ethernet phy
Code fixes include a minor error handling for the i.MX PMU driver, and
a number of firmware driver fixes:
- OP-TEE fix for supplicant based device enumeration, and a new sysfs
attribute to needed to fix a race against userspace
- Arm SCMI fix for possible truncation/overflow in the frequency
computations
- Multiple FF-A fixes for the newly added notification support"
* tag 'soc-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (55 commits)
MAINTAINERS: change the S32G2 maintainer's email address.
arm64: dts: rockchip: Fix eMMC Data Strobe PD on rk3588
ARM: dts: imx28-xea: Pass the 'model' property
ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
MAINTAINERS: reinstate freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8-apalis: set wifi regulator to always-on
ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
arm64: dts: imx8ulp: update gpio node name to align with register address
arm64: dts: imx93: update gpio node name to align with register address
arm64: dts: imx93: correct mediamix power
arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup
arm64: dts: freescale: imx8-ss-dma: Fix #pwm-cells
arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells
dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles
ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
arm64: dts: rockchip: Fix PCI node addresses on rk3399-gru
arm64: dts: rockchip: drop interrupt-names property from rk3588s dfi
firmware: arm_scmi: Fix possible frequency truncation when using level indexing mode
firmware: arm_scmi: Fix frequency truncation by promoting multiplier type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"31 hotfixes. Ten of these address pre-6.6 issues and are marked
cc:stable. The remainder address post-6.6 issues or aren't considered
serious enough to justify backporting"
* tag 'mm-hotfixes-stable-2023-12-07-18-47' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (31 commits)
mm/madvise: add cond_resched() in madvise_cold_or_pageout_pte_range()
nilfs2: prevent WARNING in nilfs_sufile_set_segment_usage()
mm/hugetlb: have CONFIG_HUGETLB_PAGE select CONFIG_XARRAY_MULTI
scripts/gdb: fix lx-device-list-bus and lx-device-list-class
MAINTAINERS: drop Antti Palosaari
highmem: fix a memory copy problem in memcpy_from_folio
nilfs2: fix missing error check for sb_set_blocksize call
kernel/Kconfig.kexec: drop select of KEXEC for CRASH_DUMP
units: add missing header
drivers/base/cpu: crash data showing should depends on KEXEC_CORE
mm/damon/sysfs-schemes: add timeout for update_schemes_tried_regions
scripts/gdb/tasks: fix lx-ps command error
mm/Kconfig: make userfaultfd a menuconfig
selftests/mm: prevent duplicate runs caused by TEST_GEN_PROGS
mm/damon/core: copy nr_accesses when splitting region
lib/group_cpus.c: avoid acquiring cpu hotplug lock in group_cpus_evenly
checkstack: fix printed address
mm/memory_hotplug: fix error handling in add_memory_resource()
mm/memory_hotplug: add missing mem_hotplug_lock
.mailmap: add a new address mapping for Chester Lin
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Devicetree fixes for the 6.7-cycle.
All over the place this time. From adapting the size of the vdec nodes
on rk3328 and rk3399, fixing some wrong pinctrl settings on rk3128 and
the Turing RK1 board, emmc-settings fixes on rk3588 and interrupt-name
mishaps, down to some dt-cleanups.
Also this adds the missing rockchip,rk3588-pmugrf compatible to the soc
grf binding, that I somehow messed up during the pull requests for the
-rc1 . At least with it included the dt-checker is happier.
* tag 'v6.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix eMMC Data Strobe PD on rk3588
arm64: dts: rockchip: Fix PCI node addresses on rk3399-gru
arm64: dts: rockchip: drop interrupt-names property from rk3588s dfi
arm64: dts: rockchip: Fix Turing RK1 interrupt pinctrls
ARM: dts: rockchip: Fix sdmmc_pwren's pinmux setting for RK3128
arm64: dts: rockchip: minor whitespace cleanup around '='
ARM: dts: rockchip: minor whitespace cleanup around '='
dt-bindings: soc: rockchip: grf: add rockchip,rk3588-pmugrf
arm64: dts: rockchip: fix rk356x pcie msg interrupt name
arm64: dts: rockchip: Expand reg size of vdec node for RK3399
arm64: dts: rockchip: Expand reg size of vdec node for RK3328
Link: https://lore.kernel.org/r/2709704.mvXUDI8C0e@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and netfilter.
Current release - regressions:
- veth: fix packet segmentation in veth_convert_skb_to_xdp_buff
Current release - new code bugs:
- tcp: assorted fixes to the new Auth Option support
Older releases - regressions:
- tcp: fix mid stream window clamp
- tls: fix incorrect splice handling
- ipv4: ip_gre: handle skb_pull() failure in ipgre_xmit()
- dsa: mv88e6xxx: restore USXGMII support for 6393X
- arcnet: restore support for multiple Sohard Arcnet cards
Older releases - always broken:
- tcp: do not accept ACK of bytes we never sent
- require admin privileges to receive packet traces via netlink
- packet: move reference count in packet_sock to atomic_long_t
- bpf:
- fix incorrect branch offset comparison with cpu=v4
- fix prog_array_map_poke_run map poke update
- netfilter:
- three fixes for crashes on bad admin commands
- xt_owner: fix race accessing sk->sk_socket, TOCTOU null-deref
- nf_tables: fix 'exist' matching on bigendian arches
- leds: netdev: fix RTNL handling to prevent potential deadlock
- eth: tg3: prevent races in error/reset handling
- eth: r8169: fix rtl8125b PAUSE storm when suspended
- eth: r8152: improve reset and surprise removal handling
- eth: hns: fix race between changing features and sending
- eth: nfp: fix sleep in atomic for bonding offload"
* tag 'net-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
vsock/virtio: fix "comparison of distinct pointer types lacks a cast" warning
net/smc: fix missing byte order conversion in CLC handshake
net: dsa: microchip: provide a list of valid protocols for xmit handler
drop_monitor: Require 'CAP_SYS_ADMIN' when joining "events" group
psample: Require 'CAP_NET_ADMIN' when joining "packets" group
bpf: sockmap, updating the sg structure should also update curr
net: tls, update curr on splice as well
nfp: flower: fix for take a mutex lock in soft irq context and rcu lock
net: dsa: mv88e6xxx: Restore USXGMII support for 6393X
tcp: do not accept ACK of bytes we never sent
selftests/bpf: Add test for early update in prog_array_map_poke_run
bpf: Fix prog_array_map_poke_run map poke update
netfilter: xt_owner: Fix for unsafe access of sk->sk_socket
netfilter: nf_tables: validate family when identifying table via handle
netfilter: nf_tables: bail out on mismatching dynset and set expressions
netfilter: nf_tables: fix 'exist' matching on bigendian arches
netfilter: nft_set_pipapo: skip inactive elements during set walk
netfilter: bpf: fix bad registration on nf_defrag
leds: trigger: netdev: fix RTNL handling to prevent potential deadlock
octeontx2-af: Update Tx link register range
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 int80 fixes from Dave Hansen:
"Avoid VMM misuse of 'int 0x80' handling in TDX and SEV guests.
It also has the very nice side effect of getting rid of a bunch of
assembly entry code"
* tag 'x86-int80-20231207' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tdx: Allow 32-bit emulation by default
x86/entry: Do not allow external 0x80 interrupts
x86/entry: Convert INT 0x80 emulation to IDTENTRY
x86/coco: Disable 32-bit emulation by default on TDX and SEV
|
|
32-bit emulation was disabled on TDX to prevent a possible attack by
a VMM injecting an interrupt on vector 0x80.
Now that int80_emulation() has a check for external interrupts the
limitation can be lifted.
To distinguish software interrupts from external ones, int80_emulation()
checks the APIC ISR bit relevant to the 0x80 vector. For
software interrupts, this bit will be 0.
On TDX, the VAPIC state (including ISR) is protected and cannot be
manipulated by the VMM. The ISR bit is set by the microcode flow during
the handling of posted interrupts.
[ dhansen: more changelog tweaks ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@vger.kernel.org> # v6.0+
|
|
The INT 0x80 instruction is used for 32-bit x86 Linux syscalls. The
kernel expects to receive a software interrupt as a result of the INT
0x80 instruction. However, an external interrupt on the same vector
also triggers the same codepath.
An external interrupt on vector 0x80 will currently be interpreted as a
32-bit system call, and assuming that it was a user context.
Panic on external interrupts on the vector.
To distinguish software interrupts from external ones, the kernel checks
the APIC ISR bit relevant to the 0x80 vector. For software interrupts,
this bit will be 0.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@vger.kernel.org> # v6.0+
|
|
There is no real reason to have a separate ASM entry point implementation
for the legacy INT 0x80 syscall emulation on 64-bit.
IDTENTRY provides all the functionality needed with the only difference
that it does not:
- save the syscall number (AX) into pt_regs::orig_ax
- set pt_regs::ax to -ENOSYS
Both can be done safely in the C code of an IDTENTRY before invoking any of
the syscall related functions which depend on this convention.
Aside of ASM code reduction this prepares for detecting and handling a
local APIC injected vector 0x80.
[ kirill.shutemov: More verbose comments ]
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@vger.kernel.org> # v6.0+
|
|
The INT 0x80 instruction is used for 32-bit x86 Linux syscalls. The
kernel expects to receive a software interrupt as a result of the INT
0x80 instruction. However, an external interrupt on the same vector
triggers the same handler.
The kernel interprets an external interrupt on vector 0x80 as a 32-bit
system call that came from userspace.
A VMM can inject external interrupts on any arbitrary vector at any
time. This remains true even for TDX and SEV guests where the VMM is
untrusted.
Put together, this allows an untrusted VMM to trigger int80 syscall
handling at any given point. The content of the guest register file at
that moment defines what syscall is triggered and its arguments. It
opens the guest OS to manipulation from the VMM side.
Disable 32-bit emulation by default for TDX and SEV. User can override
it with the ia32_emulation=y command line option.
[ dhansen: reword the changelog ]
Reported-by: Supraja Sridhara <supraja.sridhara@inf.ethz.ch>
Reported-by: Benedict Schlüter <benedict.schlueter@inf.ethz.ch>
Reported-by: Mark Kuhne <mark.kuhne@inf.ethz.ch>
Reported-by: Andrin Bertschi <andrin.bertschi@inf.ethz.ch>
Reported-by: Shweta Shinde <shweta.shinde@inf.ethz.ch>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@vger.kernel.org> # v6.0+: 1da5c9b x86: Introduce ia32_enabled()
Cc: <stable@vger.kernel.org> # v6.0+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.7:
- A MAINTAINERS update to reinstate freescale ARM64 DT directory in i.MX
entry.
- A series from Alexander Stein to fix #pwm-cells for imx8-ss.
- A series from Haibo Chen to fix GPIO node name for i.MX93 and
i.MX8ULP.
- Add parkmode-disable-ss-quirk for DWC3 on i.MX8MP and i.MX8MQ to fix
an issue that the controller may hang when processing transactions
under heavy USB traffic from multiple endpoints.
- Fix mediamix block power on/off for i.MX93 by correcting the power
domain clock to be 'nic_media'.
- A couple of Ethernet PHY clock regression fixes for imx6ul-pico and
imx6q-skov board.
- Fix edma3 power domain for i.MX8QM to fix a panic during startup
process.
* tag 'imx-fixes-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-xea: Pass the 'model' property
ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
MAINTAINERS: reinstate freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8-apalis: set wifi regulator to always-on
ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
arm64: dts: imx8ulp: update gpio node name to align with register address
arm64: dts: imx93: update gpio node name to align with register address
arm64: dts: imx93: correct mediamix power
arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup
arm64: dts: freescale: imx8-ss-dma: Fix #pwm-cells
arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells
dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles
ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
ARM: dts: imx6q: skov: fix ethernet clock regression
arm64: dt: imx93: tqma9352-mba93xxla: Fix LPUART2 pad config
Link: https://lore.kernel.org/r/20231207005202.GF270430@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fix from Helge Deller:
"A single line patch for parisc which fixes the build in tinyconfig
configurations:
- Fix asm operand number out of range build error in bug table"
* tag 'parisc-for-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix asm operand number out of range build error in bug table
|
|
Ignat Korchagin complained that a potential config regression was
introduced by commit 89cde455915f ("kexec: consolidate kexec and crash
options into kernel/Kconfig.kexec"). Before the commit, CONFIG_CRASH_DUMP
has no dependency on CONFIG_KEXEC. After the commit, CRASH_DUMP selects
KEXEC. That enforces system to have CONFIG_KEXEC=y as long as
CONFIG_CRASH_DUMP=Y which people may not want.
In Ignat's case, he sets CONFIG_CRASH_DUMP=y, CONFIG_KEXEC_FILE=y and
CONFIG_KEXEC=n because kexec_load interface could have security issue if
kernel/initrd has no chance to be signed and verified.
CRASH_DUMP has select of KEXEC because Eric, author of above commit, met a
LKP report of build failure when posting patch of earlier version. Please
see below link to get detail of the LKP report:
https://lore.kernel.org/all/3e8eecd1-a277-2cfb-690e-5de2eb7b988e@oracle.com/T/#u
In fact, that LKP report is triggered because arm's <asm/kexec.h> is
wrapped in CONFIG_KEXEC ifdeffery scope. That is wrong. CONFIG_KEXEC
controls the enabling/disabling of kexec_load interface, but not kexec
feature. Removing the wrongly added CONFIG_KEXEC ifdeffery scope in
<asm/kexec.h> of arm allows us to drop the select KEXEC for CRASH_DUMP.
Meanwhile, change arch/arm/kernel/Makefile to let machine_kexec.o
relocate_kernel.o depend on KEXEC_CORE.
Link: https://lkml.kernel.org/r/20231128054457.659452-1-bhe@redhat.com
Fixes: 89cde455915f ("kexec: consolidate kexec and crash options into kernel/Kconfig.kexec")
Signed-off-by: Baoquan He <bhe@redhat.com>
Reported-by: Ignat Korchagin <ignat@cloudflare.com>
Tested-by: Ignat Korchagin <ignat@cloudflare.com> [compile-time only]
Tested-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Eric DeVolder <eric_devolder@yahoo.com>
Tested-by: Eric DeVolder <eric_devolder@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Lee pointed out issue found by syscaller [0] hitting BUG in prog array
map poke update in prog_array_map_poke_run function due to error value
returned from bpf_arch_text_poke function.
There's race window where bpf_arch_text_poke can fail due to missing
bpf program kallsym symbols, which is accounted for with check for
-EINVAL in that BUG_ON call.
The problem is that in such case we won't update the tail call jump
and cause imbalance for the next tail call update check which will
fail with -EBUSY in bpf_arch_text_poke.
I'm hitting following race during the program load:
CPU 0 CPU 1
bpf_prog_load
bpf_check
do_misc_fixups
prog_array_map_poke_track
map_update_elem
bpf_fd_array_map_update_elem
prog_array_map_poke_run
bpf_arch_text_poke returns -EINVAL
bpf_prog_kallsyms_add
After bpf_arch_text_poke (CPU 1) fails to update the tail call jump, the next
poke update fails on expected jump instruction check in bpf_arch_text_poke
with -EBUSY and triggers the BUG_ON in prog_array_map_poke_run.
Similar race exists on the program unload.
Fixing this by moving the update to bpf_arch_poke_desc_update function which
makes sure we call __bpf_arch_text_poke that skips the bpf address check.
Each architecture has slightly different approach wrt looking up bpf address
in bpf_arch_text_poke, so instead of splitting the function or adding new
'checkip' argument in previous version, it seems best to move the whole
map_poke_run update as arch specific code.
[0] https://syzkaller.appspot.com/bug?extid=97a4fe20470e9bc30810
Fixes: ebf7d1f508a7 ("bpf, x64: rework pro/epilogue and tailcall handling in JIT")
Reported-by: syzbot+97a4fe20470e9bc30810@syzkaller.appspotmail.com
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Cc: Lee Jones <lee@kernel.org>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/bpf/20231206083041.1306660-2-jolsa@kernel.org
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
6.7, please pull the following:
- Stefan corrects the disabling of the activity LED for the Raspberry Pi
400
* tag 'arm-soc/for-6.7/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711-rpi-400: Fix delete-node of led_act
Link: https://lore.kernel.org/r/20231205225021.653045-1-florian.fainelli@broadcom.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into arm/fixes
RISC-V Devicetree fixes for v6.7-rc4
Two fixes, both rather minor. The first fixes some dtbs_check warnings
introduced after an update to the bindings, that returns the
architecture to being clean of dtbs_check issues. The second relocates
a soc-specific property to the appropriate location in $soc.dtsi, and
hopefully avoids the same mistake being copy-pasted into more
devicetrees.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-fixes-for-v6.7-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: microchip: move timebase-frequency to mpfs.dtsi
riscv: dts: sophgo: remove address-cells from intc node
Link: https://lore.kernel.org/r/20231130-maternity-majestic-dd29f0170050@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux into arm/fixes
MediaTek ARM64 DeviceTree fixes for v6.7
Fixes for various MediaTek SoCs, including
MT7986: - eMMC HS400 mode failures
- Cooling trips for emergency system shutdown
- BPI-R3 machine SFP power limit and active cooling
MT8173: - EVB device tree unit_address_vs_reg warning
MT8183: - unit_address_vs_reg and simple_bus_reg warnings
- Kukui device tree nodes naming consistency and
adhering to bindings
- Jacuzzi device tree unnecessary cells removed as
those were producing avoid_unnecessary_addr_size
MT8186: - Power domains faults due to incorrect clocks
- GPU speed bin nvmem cell name was wrong, producing
issues with interpreting the speedbin with GPU OPPs
MT8195: - Local Arbiter (and whole system) ability to suspend
- Cherry device tree interrupts_property warning
...and another unit_address_vs_reg warning on MT7622.
* tag 'mtk-dts64-fixes-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mediatek/linux:
arm64: dts: mediatek: cherry: Fix interrupt cells for MT6360 on I2C7
arm64: dts: mediatek: mt8183-kukui-jacuzzi: fix dsi unnecessary cells properties
arm64: dts: mediatek: mt7622: fix memory node warning check
arm64: dts: mediatek: mt8186: fix clock names for power domains
arm64: dts: mediatek: mt8186: Change gpu speedbin nvmem cell name
arm64: dts: mt7986: change cooling trips
arm64: dts: mt7986: define 3W max power to both SFP on BPI-R3
arm64: dts: mt7986: fix emmc hs400 mode without uboot initialization
arm64: dts: mt8183: kukui: Fix underscores in node names
arm64: dts: mediatek: mt8183: Move thermal-zones to the root node
arm64: dts: mediatek: mt8173-evb: Fix regulator-fixed node names
arm64: dts: mediatek: mt8183-evb: Fix unit_address_vs_reg warning on ntc
arm64: dts: mediatek: mt8183: Fix unit address for scp reserved memory
arm64: dts: mediatek: mt8195: Fix PM suspend/resume with venc clocks
Link: https://lore.kernel.org/r/20231129113905.134732-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We need to probe for IOCP only once during boot stage, as we were probing
for IOCP for all the stages this caused the below issue during module-init
stage,
[9.019104] Unable to handle kernel paging request at virtual address ffffffff8100d3a0
[9.027153] Oops [#1]
[9.029421] Modules linked in: rcar_canfd renesas_usbhs i2c_riic can_dev spi_rspi i2c_core
[9.037686] CPU: 0 PID: 90 Comm: udevd Not tainted 6.7.0-rc1+ #57
[9.043756] Hardware name: Renesas SMARC EVK based on r9a07g043f01 (DT)
[9.050339] epc : riscv_noncoherent_supported+0x10/0x3e
[9.055558] ra : andes_errata_patch_func+0x4a/0x52
[9.060418] epc : ffffffff8000d8c2 ra : ffffffff8000d95c sp : ffffffc8003abb00
[9.067607] gp : ffffffff814e25a0 tp : ffffffd80361e540 t0 : 0000000000000000
[9.074795] t1 : 000000000900031e t2 : 0000000000000001 s0 : ffffffc8003abb20
[9.081984] s1 : ffffffff015b57c7 a0 : 0000000000000000 a1 : 0000000000000001
[9.089172] a2 : 0000000000000000 a3 : 0000000000000000 a4 : ffffffff8100d8be
[9.096360] a5 : 0000000000000001 a6 : 0000000000000001 a7 : 000000000900031e
[9.103548] s2 : ffffffff015b57d7 s3 : 0000000000000001 s4 : 000000000000031e
[9.110736] s5 : 8000000000008a45 s6 : 0000000000000500 s7 : 000000000000003f
[9.117924] s8 : ffffffc8003abd48 s9 : ffffffff015b1140 s10: ffffffff8151a1b0
[9.125113] s11: ffffffff015b1000 t3 : 0000000000000001 t4 : fefefefefefefeff
[9.132301] t5 : ffffffff015b57c7 t6 : ffffffd8b63a6000
[9.137587] status: 0000000200000120 badaddr: ffffffff8100d3a0 cause: 000000000000000f
[9.145468] [<ffffffff8000d8c2>] riscv_noncoherent_supported+0x10/0x3e
[9.151972] [<ffffffff800027e8>] _apply_alternatives+0x84/0x86
[9.157784] [<ffffffff800029be>] apply_module_alternatives+0x10/0x1a
[9.164113] [<ffffffff80008fcc>] module_finalize+0x5e/0x7a
[9.169583] [<ffffffff80085cd6>] load_module+0xfd8/0x179c
[9.174965] [<ffffffff80086630>] init_module_from_file+0x76/0xaa
[9.180948] [<ffffffff800867f6>] __riscv_sys_finit_module+0x176/0x2a8
[9.187365] [<ffffffff80889862>] do_trap_ecall_u+0xbe/0x130
[9.192922] [<ffffffff808920bc>] ret_from_exception+0x0/0x64
[9.198573] Code: 0009 b7e9 6797 014d a783 85a7 c799 4785 0717 0100 (0123) aef7
[9.205994] ---[ end trace 0000000000000000 ]---
This is because we called riscv_noncoherent_supported() for all the stages
during IOCP probe. riscv_noncoherent_supported() function sets
noncoherent_supported variable to true which has an annotation set to
"__ro_after_init" due to which we were seeing the above splat. Fix this by
probing for IOCP only once in boot stage by having a boolean variable
"done" which will be set to true upon IOCP probe in errata_probe_iocp()
and we bail out early if "done" is set to true.
While at it make return type of errata_probe_iocp() to void as we were
not checking the return value in andes_errata_patch_func().
Fixes: e021ae7f5145 ("riscv: errata: Add Andes alternative ports")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Link: https://lore.kernel.org/r/20231130212647.108746-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This fixes two bugs in SCS initialization for secondary CPUs. First,
the SCS was not initialized at all in the spinwait boot path. Second,
the code for the SBI HSM path attempted to initialize the SCS before
enabling the MMU. However, that involves dereferencing the thread
pointer, which requires the MMU to be enabled.
Fix both issues by setting up the SCS in the common secondary entry
path, after enabling the MMU.
Fixes: d1584d791a29 ("riscv: Implement Shadow Call Stack")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20231121211958.3158576-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This is a backport of a fix that was done in OpenSBI: ec0559eb315b
("lib: sbi_misaligned_ldst: Fix handling of C.SWSP and C.SDSP").
Unlike C.LWSP/C.LDSP, these encodings can be used with the zero
register, so checking that the rs2 field is non-zero is unnecessary.
Additionally, the previous check was incorrect since it was checking
the immediate field of the instruction instead of the rs2 field.
Fixes: 956d705dd279 ("riscv: Unaligned load/store handling for M_MODE")
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Link: https://lore.kernel.org/r/20231103090223.702340-1-cleger@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Extensions are getting added quickly and their hwprobe bits will soon
exceed 31 (which pair values accommodate, since they're of type u64).
However, in one tree, where a bunch of extensions got merged prior to
zicboz, zicboz already got pushed to bit 32. Pushing it exposed a
32-bit compilation bug, since unsigned long was used instead of u64.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310311801.hxduISrr-lkp@intel.com/
Fixes: 9c7646d5ffd2 ("RISC-V: hwprobe: Expose Zicboz extension and its block size")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20231101141908.192198-2-ajones@ventanamicro.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Use opcodes available to both rv32 and rv64 in uleb128 module linking
test.
Fixes: af71bc194916 ("riscv: Add tests for riscv module loading")
Signed-off-by: Charlie Jenkins <charlie@rivosinc.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/lkml/1d7c71ee-5742-4df4-b8ef-a2aea0a624eb@infradead.org/
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20231122-module_fixup-v2-1-dfb9565e9ea5@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
JEDEC standard JESD84-B51 defines the eMMC Data Strobe line, which is
currently used only in HS400 mode, as a device->host clock signal that
"is used only in read operation. The Data Strobe is always High-Z (not
driven by the device and pulled down by RDS) or Driven Low in write
operation, except during CRC status response." RDS is a pull-down
resistor specified in the 10K-100K ohm range. Thus per the standard, the
Data Strobe is always pulled to ground (by the eMMC and/or RDS) during
write operations.
Evidently, the eMMC host controller in the RK3588 considers an active
voltage on the eMMC-DS line during a write to be an error.
The default (i.e. hardware reset, and Rockchip BSP) behavior for the
RK3588 is to activate the eMMC-DS pin's builtin pull-down. As a result,
many RK3588 board designers do not bother adding a dedicated RDS
resistor, instead relying on the RK3588's internal bias. The current
devicetree, however, disables this bias (`pcfg_pull_none`), breaking
HS400-mode writes for boards without a dedicated RDS, but with an eMMC
chip that chooses to High-Z (instead of drive-low) the eMMC-DS line.
(The Turing RK1 is one such board.)
Fix this by changing the bias in the (common) emmc_data_strobe case to
reflect the expected hardware/BSP behavior. This is unlikely to cause
regressions elsewhere: the pull-down is only relevant for High-Z eMMCs,
and if this is redundant with a (dedicated) RDS resistor, the effective
result is only a lower resistance to ground -- where the range of
tolerance is quite high. If it does, it's better fixed in the specific
devicetrees.
Fixes: d85f8a5c798d5 ("arm64: dts: rockchip: Add rk3588 pinctrl data")
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Link: https://lore.kernel.org/r/20231205202900.4617-2-CFSworks@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Per root-node.yaml, 'model' is a required property.
Pass it to fix the following dt-schema warning:
imx28-xea.dtb: /: 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fixes: 445ae16ac1c5 ("ARM: dts: imx28: Add DTS description of imx28 based XEA board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The timer nodes declare compatibility with "fsl,imx6sx-gpt", which
itself is compatible with "fsl,imx6dl-gpt". Switch the fallback
compatible from "fsl,imx6sx-gpt" to "fsl,imx6dl-gpt".
Fixes: 949673450291 ("ARM: dts: add imx7d soc dtsi file")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure that the wifi regulator is always on. The wifi driver itself
puts the wifi module into suspend mode. If we cut the power the driver
will crash when resuming from suspend.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fixes: ad0de4ceb706 ("arm64: dts: freescale: add initial apalis imx8 aka quadmax module support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
Release the id allocated in 'mmdc_pmu_init' when 'devm_kasprintf'
return NULL
Suggested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Fixes: e76bdfd7403a ("ARM: imx: Added perf functionality to mmdc driver")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Change the gpio node name to align with register address.
Fixes: ac7bcf48ddba ("arm64: dts: imx8ulp: update gpio node")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Change the gpio node name to align with register address
Fixes: c1d0782b5fc3 ("arm64: dts: imx93: update gpio node")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
"nic_media" clock should be enabled when power on/off mediamix, otherwise
power on/off will fail. Because "media_axi_root" clock is the parent of
"nic_media" clock, so replace "media_axi_clock" clock with "nic_media"
clock in mediamix node.
Link: https://github.com/nxp-imx/linux-imx/commit/ce18e6d0071ae9df5486af8613708ebe920484be
Fixes: f2d03ba997cb ("arm64: dts: imx93: reorder device nodes")
Fixes: e85d3458a804 ("arm64: dts: imx93: add src node")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add imx8qm's own pm, otherwise the following panic will
occur during the startup process:
Kernel panic - not syncing: Asynchronous SError Interrupt
Hardware name: Freescale i.MX8QM MEK (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace+0x98/0xf0
show_stack+0x18/0x24
dump_stack_lvl+0x60/0xac
dump_stack+0x18/0x24
panic+0x340/0x3a0
nmi_panic+0x8c/0x90
arm64_serror_panic+0x6c/0x78
do_serror+0x3c/0x78
el1h_64_error_handler+0x38/0x50
el1h_64_error+0x64/0x68
fsl_edma_chan_mux+0x98/0xdc
fsl_edma_probe+0x278/0x898
platform_probe+0x68/0xd8
really_probe+0x110/0x27c
__driver_probe_device+0x78/0x12c
driver_probe_device+0x3c/0x118
__device_attach_driver+0xb8/0xf8
bus_for_each_drv+0x84/0xe4
__device_attach+0xfc/0x18c
device_initial_probe+0x14/0x20
Fixes: e4d7a330fb7a ("arm64: dts: imx8: add edma[0..3]")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8QXP supports inverted PWM output, thus #pwm-cells needs to be set
to 3.
Fixes: f1d6a6b991ef9 ("arm64: dts: imx8qxp: add adma_pwm in adma")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
