| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only a handful of device tree fixes, all simple enough:
NVIDIA Tegra:
- Fix a regression for booting on chromebooks
TI OMAP:
- Two fixes PHY mode on am335x reference boards
Marvell mvebu:
- A regression fix for Armada XP NAND flash controllers
- An incorrect reset signal on the clearfog board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: tegra: Restore DT ABI on Tegra124 Chromebooks
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
|
|
arm/fixes
mvebu fixes for 5.0 (part 2)
Fix PHY reset signal on clearfog gt 8K (Armada 8040 based)
Fix NAND description on Armada XP boards which was broken since a few
release
* tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Two am335x ethernet phy mode fixes for v5.0-rc cycle
Recent changes with commit cd28d1d6e52e: ("net: phy: at803x: Disable phy
delay for RGMII mode") broke Ethernet on am335x-evmsk, and turns out some
device driver fixes are needed.
Even without the driver fixes, am335x needs to run in rgmii-id mode instead
rgmii-txid mode. Things have been working based on luck as the broken driver
has been configuring rgmii-id mode. Let's fix that as that way things work
as they're supposed to work from hardware wiring point of view.
* tag 'omap-for-v5.0/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 482997699ef0 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings
for /memory") inadventently broke device tree ABI by adding a unit-
address to the "/memory" node because the device tree compiler flagged
the missing unit-address as a warning.
Tegra124 Chromebooks (a.k.a. Nyan) use a bootloader that relies on the
full name of the memory node in device tree being exactly "/memory". It
can be argued whether this was a good decision or not, and some other
bootloaders (such as U-Boot) do accept a unit-address in the name of the
node, but the device tree is an ABI and we can't break existing setups
just because the device tree compiler considers it bad practice to omit
the unit-address nowadays.
This partially reverts the offending commit and restores device tree ABI
compatibility.
Fixes: 482997699ef0 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory")
Reported-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Two easily resolvable overlapping change conflicts, one in
TCP and one in the eBPF verifier.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 3b79919946cd2cf4dac47842afc9a893acec4ed7 ("ARM: dts:
armada-370-xp: update NAND node with new bindings") updated some
Marvell Armada DT description to use the new NAND controller bindings,
but did it incorrectly for a number of boards: armada-xp-gp,
armada-xp-db and armada-xp-lenovo-ix4-300d. Due to this, the NAND is
no longer detected on those platforms.
This commit fixes that by properly using the new NAND DT binding. This
commit was runtime-tested on Armada XP GP, the two other platforms are
only compile-tested.
Fixes: 3b79919946cd2 ("ARM: dts: armada-370-xp: update NAND node with new bindings")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Pull ARM fixes from Russell King:
"A few ARM fixes:
- Dietmar Eggemann noticed an issue with IRQ migration during CPU
hotplug stress testing.
- Mathieu Desnoyers noticed that a previous fix broke optimised
kprobes.
- Robin Murphy noticed a case where we were not clearing the dma_ops"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8835/1: dma-mapping: Clear DMA ops on teardown
ARM: 8834/1: Fix: kprobes: optimized kprobes illegal instruction
ARM: 8824/1: fix a migrating irq bug when hotplug cpu
|
|
Pull KVM fixes from Paolo Bonzini:
"A somewhat bigger ARM update, and the usual smattering of x86 bug
fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: vmx: Fix entry number check for add_atomic_switch_msr()
KVM: x86: Recompute PID.ON when clearing PID.SN
KVM: nVMX: Restore a preemption timer consistency check
x86/kvm/nVMX: read from MSR_IA32_VMX_PROCBASED_CTLS2 only when it is available
KVM: arm64: Forbid kprobing of the VHE world-switch code
KVM: arm64: Relax the restriction on using stage2 PUD huge mapping
arm: KVM: Add missing kvm_stage2_has_pmd() helper
KVM: arm/arm64: vgic: Always initialize the group of private IRQs
arm/arm64: KVM: Don't panic on failure to properly reset system registers
arm/arm64: KVM: Allow a VCPU to fully reset itself
KVM: arm/arm64: Reset the VCPU without preemption and vcpu state loaded
arm64: KVM: Don't generate UNDEF when LORegion feature is present
KVM: arm/arm64: vgic: Make vgic_cpu->ap_list_lock a raw_spinlock
KVM: arm/arm64: vgic: Make vgic_dist->lpi_list_lock a raw_spinlock
KVM: arm/arm64: vgic: Make vgic_irq->irq_lock a raw_spinlock
|
|
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fix omap4 and later lost cpu1 interrupts for periodic timer
A fix from Russell that took a while to get applied into fixes as
I thought Russell is merging this one.
* tag 'omap-for-v5.0/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: fix lack of timer interrupts on CPU1 after hotplug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Drop one non-existent component from powerdomain list.
* tag 'v5.0-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove qos_cif1 from rk3188 power-domain
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
SoC fixes for omaps for v5.0-rc cycle
This series contains two SoC regression fixes and one uninitialized
variable fix:
- Fix inverted nirq pin handling for omap5 that started producing
warnings with earlier GIC direction checks and took a while to
understand and confirm. Basically there are two sys_nirq pins
that are bypassing peripheral modules and inverted automatically
by the SoC and need to be handled with a custom irq_set_type()
- Recent ti-sysc changes caused a regression to the pwm-omap-dmtimer
code where the device tree handling code for timer source clock
gets confused. It looks like we can remove that code eventually,
but for now we just drop a bogus pm_runtime_irq_safe() for the
timers with the related quirks caused by pm_runtime_irq_safe(),
and have the standard assigned-clocks and assigned-clock-parents
deal with setting the source clock
- Fix potentially uninitialized value for display init code if
regmap_read() fails
* tag 'omap-for-v5.0/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Variable "reg" in function omap4_dsi_mux_pads() could be uninitialized
ARM: dts: Configure clock parent for pwm vibra
bus: ti-sysc: Fix timer handling with drop pm_runtime_irq_safe()
ARM: OMAP5+: Fix inverted nirq pin interrupts with irq_set_type
clocksource: timer-ti-dm: Fix pwm dmtimer usage of fck reparenting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for 5.0:
- Fix the way we reset vcpus, plugging the race that could happen on VHE
- Fix potentially inconsistent group setting for private interrupts
- Don't generate UNDEF when LORegion feature is present
- Relax the restriction on using stage2 PUD huge mapping
- Turn some spinlocks into raw_spinlocks to help RT compliance
|
|
Installing the appropriate non-IOMMU DMA ops in arm_iommu_detch_device()
serves the case where IOMMU-aware drivers choose to control their own
mapping but still make DMA API calls, however it also affects the case
when the arch code itself tears down the mapping upon driver unbinding,
where the ops now get left in place and can inhibit arch_setup_dma_ops()
on subsequent re-probe attempts.
Fix the latter case by making sure that arch_teardown_dma_ops() cleans
up whenever the ops were automatically installed by its counterpart.
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 1874619a7df4 "ARM: dma-mapping: Set proper DMA ops in arm_iommu_detach_device()"
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
commit e46daee53bb5 ("ARM: 8806/1: kprobes: Fix false positive with
FORTIFY_SOURCE") introduced a regression in optimized kprobes. It
triggers "invalid instruction" oopses when using kprobes instrumentation
through lttng and perf. This commit was introduced in kernel v4.20, and
has been backported to stable kernels 4.19 and 4.14.
This crash was also reported by Hongzhi Song on the redhat bugzilla
where the patch was originally introduced.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1639397
Link: https://bugs.lttng.org/issues/1174
Link: https://lore.kernel.org/lkml/342740659.2887.1549307721609.JavaMail.zimbra@efficios.com
Fixes: e46daee53bb5 ("ARM: 8806/1: kprobes: Fix false positive with FORTIFY_SOURCE")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reported-by: Robert Berger <Robert.Berger@ReliableEmbeddedSystems.com>
Tested-by: Robert Berger <Robert.Berger@ReliableEmbeddedSystems.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Robert Berger <Robert.Berger@ReliableEmbeddedSystems.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: William Cohen <wcohen@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: <stable@vger.kernel.org> # v4.14+
Cc: linux-arm-kernel@lists.infradead.org
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two very minor fixes: one remove of a #include for an unused header
and a fix of the xen ML address in MAINTAINERS"
* tag 'for-linus-5.0-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: unify reference to xen-devel list
arch/arm/xen: Remove duplicate header
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a bit larger than normal, as we had not managed to send out a
pull request before traveling for a week without my signing key.
There are multiple code fixes for older bugs, all of which should get
backported into stable kernels:
- tango: one fix for multiplatform configurations broken on other
platforms when tango is enabled
- arm_scmi: device unregistration fix
- iop32x: fix kernel oops from extraneous __init annotation
- pxa: remove a double kfree
- fsl qbman: close an interrupt clearing race
The rest is the usual collection of smaller fixes for device tree
files, on the renesas, allwinner, meson, omap, davinci, qualcomm and
imx platforms.
Some of these are for compile-time warnings, most are for board
specific functionality that fails to work because of incorrect
settings"
* tag 'armsoc-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (30 commits)
ARM: tango: Improve ARCH_MULTIPLATFORM compatibility
firmware: arm_scmi: provide the mandatory device release callback
ARM: iop32x/n2100: fix PCI IRQ mapping
arm64: dts: add msm8996 compatible to gicv3
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: pxa: ssp: unneeded to free devm_ allocated data
ARM: dts: r8a7743: Convert to new LVDS DT bindings
soc: fsl: qbman: avoid race in clearing QMan interrupt
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
ARM: dts: da850: fix interrupt numbers for clocksource
dt-bindings: imx8mq: Number clocks consecutively
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
...
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the comphy settings for the Ethernet interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the DT description for the Armada 38x common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have a kernel configured for periodic timer interrupts, and we
have cpuidle enabled, then we end up with CPU1 losing timer interupts
after a hotplug.
This can manifest itself in RCU stall warnings, or userspace becoming
unresponsive.
The problem is that the kernel initially wants to use the TWD timer
for interrupts, but the TWD loses context when we enter the C3 cpuidle
state. Nothing reprograms the TWD after idle.
We have solved this in the past by switching to broadcast timer ticks,
and cpuidle44xx switches to that mode at boot time. However, there is
nothing to switch from periodic mode local timers after a hotplug
operation.
We call tick_broadcast_enter() in omap_enter_idle_coupled(), which one
would expect would take care of the issue, but internally this only
deals with one-shot local timers - tick_broadcast_enable() on the other
hand only deals with periodic local timers. So, we need to call both.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[tony@atomide.com: just standardized the subject line]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixup 32bit by providing the now required helper.
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Failing to properly reset system registers is pretty bad. But not
quite as bad as bringing the whole machine down... So warn loudly,
but slightly more gracefully.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
|
|
The current kvm_psci_vcpu_on implementation will directly try to
manipulate the state of the VCPU to reset it. However, since this is
not done on the thread that runs the VCPU, we can end up in a strangely
corrupted state when the source and target VCPUs are running at the same
time.
Fix this by factoring out all reset logic from the PSCI implementation
and forwarding the required information along with a request to the
target VCPU.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
|
|
Arm TC2 fails cpu hotplug stress test.
This issue was tracked down to a missing copy of the new affinity
cpumask for the vexpress-spc interrupt into struct
irq_common_data.affinity when the interrupt is migrated in
migrate_one_irq().
Fix it by replacing the arm specific hotplug cpu migration with the
generic irq code.
This is the counterpart implementation to commit 217d453d473c ("arm64:
fix a migrating irq bug when hotplug cpu").
Tested with cpu hotplug stress test on Arm TC2 (multi_v7_defconfig plus
CONFIG_ARM_BIG_LITTLE_CPUFREQ=y and CONFIG_ARM_VEXPRESS_SPC_CPUFREQ=y).
The vexpress-spc interrupt (irq=22) on this board is affine to CPU0.
Its affinity cpumask now changes correctly e.g. from 0 to 1-4 when
CPU0 is hotplugged out.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Revert armada8k GPIO reset change that broke Macchiatobin booting
(Baruch Siach)
- Use actual size config reads on ARM cns3xxx (Koen Vandeputte)
- Fix ARM cns3xxx config write alignment issue (Koen Vandeputte)
- Fix imx6 PHY device link error checking (Leonard Crestez)
- Fix imx6 probe failure on chips without separate PCI power domain
(Leonard Crestez)
* tag 'pci-v5.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: armada8k: Add support for gpio controlled reset signal"
ARM: cns3xxx: Use actual size reads for PCIe
ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment
PCI: imx: Fix checking pd_pcie_phy device link addition
PCI: imx: Fix probe failure without power domain
|
|
commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") reimplemented cns3xxx_pci_read_config() using
pci_generic_config_read32(), which preserved the property of only doing
32-bit reads.
It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.
Given that:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended
Allow read access of any size by replacing pci_generic_config_read32()
with the pci_generic_config_read() accessors.
Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Krzysztof Halasa <khalasa@piap.pl>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
CC: Tim Harvey <tharvey@gateworks.com>
|
|
Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.
Commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:
cns3xxx_pci_write_config() --> pci_generic_config_write()
cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.
This currently leads to pci_generic_config_write() writing to the wrong
registers.
For instance, upon ath9k module loading:
- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
(CACHE_LINE_SIZE)
Fix the bug by removing the alignment in the cns3xxx mapping function.
Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org # v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
|
|
Calling platform-specific code unconditionally blows up when running
an ARCH_MULTIPLATFORM kernel on a different platform. Don't do it.
Reported-by: Paolo Pisati <p.pisati@gmail.com>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: stable@vger.kernel.org # v4.8+
Fixes: a30eceb7a59d ("ARM: tango: add Suspend-to-RAM support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Third Round of Renesas ARM Based SoC Fixes for v5.0
* Convert to new LVDS DT bindings fixing a regression introduced in v4.17
* tag 'renesas-fixes3-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7743: Convert to new LVDS DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixes
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Booting 4.20 on a TheCUS N2100 results in a kernel oops while probing
PCI, due to n2100_pci_map_irq() having been discarded during boot.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: stable@vger.kernel.org # 2.6.18+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Device tree fixes for omaps for v5.0-rc cycle
This series of dts fixes for omap devices fixes several device specific
regressions:
- The onenand timings for n950/n9 have been wrong for a while since
we moved to dts based timings
- A typo for the cpcap pmic is now producing erors during boot as the
level should be 0 for unconfigurable triggering instead of 1
- Changes for ti-sysc for omap5 left uart3 with debug flags that should
not be set
- Fix a new dtc warning started showing up for omap3-gta04 grap_port
- With the generic MMC card detection code we need to fix the gpio
in dts for n900 and am335x-shc
* tag 'omap-for-v5.0/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: dts: Remove unnecessary idle flags for omap5 uart3
ARM: dts: omap4-droid4: Fix typo in cpcap IRQ flags
ARM: OMAP: dts: N950/N9: fix onenand timings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
This fixes a long standing typo in device-tree for DA850 in interrupt
number for timer. It did not affect us so far because we use non-DT
timer driver within mach-davinci. This was caught while migrating to
clocksource driver.
* tag 'davinci-fixes-for-v5.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: fix interrupt numbers for clocksource
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This is the pxa fixes set for v4.20 cycle:
- only a single devm allocated pointer free fix, which was never
triggered runtime but code analysis found.
* tag 'pxa-fixes-5.0' of https://github.com/rjarzmik/linux:
ARM: pxa: ssp: unneeded to free devm_ allocated data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.0:
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
* tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
uninitialized
In function omap4_dsi_mux_pads(), local variable "reg" could
be uninitialized if function regmap_read() returns -EINVAL.
However, it will be used directly in the later context, which
is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Commit 84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") moved some omap4 timers to probe with ti-sysc
interconnect target module. Turns out this broke pwm-omap-dmtimer
for reparenting of the timer clock.
With ti-sysc, we can now configure the clock sources in the dts with
assigned-clocks and assigned-clock-parents.
Fixes: 84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-01-29
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Teach verifier dead code removal, this also allows for optimizing /
removing conditional branches around dead code and to shrink the
resulting image. Code store constrained architectures like nfp would
have hard time doing this at JIT level, from Jakub.
2) Add JMP32 instructions to BPF ISA in order to allow for optimizing
code generation for 32-bit sub-registers. Evaluation shows that this
can result in code reduction of ~5-20% compared to 64 bit-only code
generation. Also add implementation for most JITs, from Jiong.
3) Add support for __int128 types in BTF which is also needed for
vmlinux's BTF conversion to work, from Yonghong.
4) Add a new command to bpftool in order to dump a list of BPF-related
parameters from the system or for a specific network device e.g. in
terms of available prog/map types or helper functions, from Quentin.
5) Add AF_XDP sock_diag interface for querying sockets from user
space which provides information about the RX/TX/fill/completion
rings, umem, memory usage etc, from Björn.
6) Add skb context access for skb_shared_info->gso_segs field, from Eric.
7) Add support for testing flow dissector BPF programs by extending
existing BPF_PROG_TEST_RUN infrastructure, from Stanislav.
8) Split BPF kselftest's test_verifier into various subgroups of tests
in order better deal with merge conflicts in this area, from Jakub.
9) Add support for queue/stack manipulations in bpftool, from Stanislav.
10) Document BTF, from Yonghong.
11) Dump supported ELF section names in libbpf on program load
failure, from Taeung.
12) Silence a false positive compiler warning in verifier's BTF
handling, from Peter.
13) Fix help string in bpftool's feature probing, from Prashant.
14) Remove duplicate includes in BPF kselftests, from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicate header which is included twice.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
|
|
This patch implements code-gen for new JMP32 instructions on arm.
For JSET, "ands" (AND with flags updated) is used, so corresponding
encoding helper is added.
Cc: Shubham Bansal <illusionist.neo@gmail.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Commit 83a86fbb5b56 ("irqchip/gic: Loudly complain about the use of
IRQ_TYPE_NONE") started warning about incorrect dts usage for irqs.
ARM GIC only supports active-high interrupts for SPI (Shared Peripheral
Interrupts), and the Palmas PMIC by default is active-low.
Palmas PMIC allows changing the interrupt polarity using register
PALMAS_POLARITY_CTRL_INT_POLARITY, but configuring sys_nirq1 with
a pull-down and setting PALMAS_POLARITY_CTRL_INT_POLARITY made the
Palmas RTC interrupts stop working. This can be easily tested with
kernel tools rtctest.c.
Turns out the SoC inverts the sys_nirq pins for GIC as they do not go
through a peripheral device but go directly to the MPUSS wakeupgen.
I've verified this by muxing the interrupt line temporarily to gpio_wk16
instead of sys_nirq1. with a gpio, the interrupt works fine both
active-low and active-high with the SoC internal pull configured and
palmas polarity configured. But as sys_nirq1, the interrupt only works
when configured ACTIVE_LOW for palmas, and ACTIVE_HIGH for GIC.
Note that there was a similar issue earlier with tegra114 and palmas
interrupt polarity that got fixed by commit df545d1cd01a ("mfd: palmas:
Provide irq flags through DT/platform data"). However, the difference
between omap5 and tegra114 is that tegra inverts the palmas interrupt
twice, once when entering tegra PMC, and again when exiting tegra PMC
to GIC.
Let's fix the issue by adding a custom wakeupgen_irq_set_type() for
wakeupgen and invert any interrupts with wrong polarity. Let's also
warn about any non-sysnirq pins using wrong polarity. Note that we
also need to update the dts for the level as IRQ_TYPE_NONE never
has irq_set_type() called, and let's add some comments and use proper
pin nameing to avoid more confusion later on.
Cc: Belisko Marek <marek.belisko@gmail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
cd pin on mmc1 is GPIO_ACTIVE_LOW not GPIO_ACTIVE_HIGH
Fixes: e63201f19438 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
