| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.
PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Tested-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Set Medfield SDIO as non-removable to avoid un-necessary
card detect activity.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated. Instead
just accept the regulator's voltage.
This patch adds MMC_CAP2_BROKEN_VOLTAGE.
If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c. When changing the voltage, maybe use
regulator_set_voltage().
In regulator_set_voltage(), check the below condition.
/* sanity check */
if (!rdev->desc->ops->set_voltage &&
!rdev->desc->ops->set_voltage_sel) {
ret = -EINVAL;
goto out;
}
If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.
So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch fixes the failure of low speed mmc card detection.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When accessing the card on some FSL platform boards (e.g p2020, p1010,
mpc8536), the following error is reported with the timeout value calculated:
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
So we skip the calculation of timeout and use the max value to fix it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For some FSL ESDHC controllers (e.g. P2020E, Rev1.0), the SDHC can not
work on DMA mode because of the hardware bug, so we set a broken dma flag
and use PIO mode.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The voltage_ranges is supposed to switch from big endian to little endian.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
A UHS sdio card that fails initialization at 1.8v signaling is not in
UHS mode. We cannot use the speed in the the cis to reflect the bus
speed as this is the maxiumum value and will not reflect the fact
that the host is operating at a lower (non uhs) bus speed.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module: fix broken isapnp handling in file2alias
module: make module param bint handle nul value
|
|
Handling of isapnp module aliases was broken by commit
626596e295d477c0fefa08cd5daa7dd011b1bb2c by changing "isapnp" string to "isa".
The code was then modified by commit
e49ce14150c64b29a8dd211df785576fa19a9858 but this bug remained.
Change the string back to "isapnp".
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Allow bint param accept nul values, just do same as bool param.
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
git://git.infradead.org/users/cbou/battery-urgent
Just a few small fixes for a bunch of drivers. Nothing noteworthy.
* tag 'battery-fixes-for-v3.3-rc2' of git://git.infradead.org/users/cbou/battery-urgent:
lp8727_charger: Add terminating entry for i2c_device_id table
power_supply: Fix modalias for charger-manager
lp8727_chager: Fix permissions on a header file
bq27x00_battery: Fix flag register read
Revert "bq27x00_battery: Fix reporting status value for bq27500 battery"
|
|
Two bugfixes in XFS for 3.3: one fix passes KMEM_SLEEP to kmem_realloc
instead of 0, and the other resolves a possible deadlock in xfs quotas.
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: use a normal shrinker for the dquot freelist
xfs: pass KM_SLEEP flag to kmem_realloc() in xlog_recover_add_to_cnt_trans()
|
|
This set of changes are fixing various section mismatch warnings which
look to be completely valid. Primerily, those which are fixed are those
which can cause oopses by manipulation of driver binding via sysfs. For
example: calling code marked __init from driver probe __devinit
functions.
Some of these changes will be reworked at the next merge window when the
underlying reasons are sorted out. In the mean time, I think it's
important to have this fixed for correctness.
Also included in this set are fixes to various error messages in OMAP -
including making them gramatically correct, fixing a few spelling
errors, and more importantly, making them greppable by unwrapping them.
Tony Lindgren has acked all these patches, put them out for testing a
week ago, and I've tested them on the platforms I have.
* 'omap-fixes-warnings' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: resolve nebulous 'Error setting wl12xx data'
ARM: omap: fix wrapped error messages in omap_hwmod.c
ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c
ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup()
ARM: omap: fix section mismatch error for omap_4430sdp_display_init()
ARM: omap: fix section mismatch warning for omap_secondary_startup()
ARM: omap: preemptively fix section mismatch in omap4_sdp4430_wifi_mux_init()
ARM: omap: fix section mismatch warning in mux.c
ARM: omap: fix section mismatch errors in TWL PMIC driver
ARM: omap: fix uninformative vc/i2c configuration error message
ARM: omap: fix vc.c PMIC error message
ARM: omap: fix prm44xx.c OMAP44XX_IRQ_PRCM build error
|
|
This pull request covers the major oopsing issues with OMAP, caused by
the lack of the TWL driver. Even when the TWL driver is not built in,
we shouldn't oops.
* 'omap-fixes-urgent' of git://git.linaro.org/people/rmk/linux-arm:
ARM: omap: fix broken twl-core dependencies and ifdefs
ARM: omap: fix oops in drivers/video/omap2/dss/dpi.c
ARM: omap: fix oops in arch/arm/mach-omap2/vp.c when pmic is not found
|
|
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7322/1: Print BUG instead of undefined instruction on BUG_ON()
ARM: 7321/1: cache-v7: Disable preemption when reading CCSIDR
ARM: 7320/1: Fix proc_info table alignment
|
|
Some code - especially the crypto layer - wants to use the x86
FP/MMX/AVX register set in what may be interrupt (typically softirq)
context.
That *can* be ok, but the tests for when it was ok were somewhat
suspect. We cannot touch the thread-specific status bits either, so
we'd better check that we're not going to try to save FP state or
anything like that.
Now, it may be that the TS bit is always cleared *before* we set the
USEDFPU bit (and only set when we had already cleared the USEDFP
before), so the TS bit test may actually have been sufficient, but it
certainly was not obviously so.
So this explicitly verifies that we will not touch the TS_USEDFPU bit,
and adds a few related sanity-checks. Because it seems that somehow
AES-NI is corrupting user FP state. The cause is not clear, and this
patch doesn't fix it, but while debugging it I really wanted the code to
be more obviously correct and robust.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It was marked asmlinkage for some really old and stale legacy reasons.
Fix that and the equally stale comment.
Noticed when debugging the irq_fpu_usable() bugs.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
sound/pci/hda/patch_realtek.c
Merged back the fix for Acer Aspire 6935 with ALC889 codec.
The fix commit was based on 3.2 kernel so that it can be applied to
stable kernel cleanly.
|
|
Since 3.2 kernel, the driver starts trying to assign the multi-io DACs
before the speaker, thus it assigns DAC2/3 for multi-io and DAC4 for
the speaker for a standard laptop setup like a HP, a speaker, a mic-in
and a line-in. However, on Acer Aspire 6935, it seems that the
speaker pin 0x14 must be connected with either DAC1 or 2; otherwise it
results in silence by some reason, although the codec itself allows
the routing to DAC3/4.
As a workaround, the connection list of each pin is reduced to be
mapped to either only DAC1/2 or DAC3/4, so that the compatible
assignment as in kernel 3.1 is achieved.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42740
Cc: <stable@kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
VT1705 codec has two ADCs where the secondary ADC has no MUX but only
a fixed connection to the mic pin. This confused the driver and it
tries always overriding the input-source selection by assumption of
the existing MUX for the secondary ADC, resulted in resetting the
input-source at each time PM (including power-saving) occurs.
The fix is simply to check the existence of MUX for secondary ADCs in
the initialization code.
Tested-by: Anisse Astier <anisse@astier.eu>
Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It's useful to print the error code when a called function fails so a
diagnosis of why it failed is possible. In this case, it fails because
we try to register some data for the wl12xx driver, but as the driver
is not configured, a stub function is used which simply returns -ENOSYS.
Let's do the simple thing for -rc and print the error code.
Also, the return code from platform_register_device() at each of these
sites was not being checked. Add some checking, and again print the
error code.
This should be fixed properly for the next merge window so we don't
issue error messages merely because a driver is not configured.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
While trying to debug my OMAP platforms, they emitted this message:
omap_hwmod: %s: enabled state can only be entered from initialized, idle, or disabled state
The following backtrace said it was from a function called '_enable',
which didn't provide much clue. Grepping didn't find it either.
The message is wrapped, so unwrap the message so grep can find it. Do
the same for three other messages in this file.
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The previous commit causes new section mismatch warnings:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb30): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb4c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_gpio()
The function omap_init_hsmmc() references
the function __init omap_mux_init_gpio().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_gpio is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb60): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb6c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb78): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb90): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdb9c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdba8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbc0): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbcc): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbd8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdbf8): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc04): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc10): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc28): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc34): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc40): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc58): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc64): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc70): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xdc7c): Section mismatch in reference from the function omap_init_hsmmc() to the function .init.text:omap_mux_init_signal()
The function omap_init_hsmmc() references
the function __init omap_mux_init_signal().
This is often because omap_init_hsmmc lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Again, as for omap2_hsmmc_init(), these functions are callable at
runtime via the gpio-twl4030.c driver, and so these can't be marked
__init.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xd0f0): Section mismatch in reference from the function sdp3430_twl_gpio_setup() to the function .init.text:omap2_hsmmc_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap2_hsmmc_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap2_hsmmc_init is wrong.
sdp3430_twl_gpio_setup() is called via platform data from the
gpio-twl4030 module, which can be inserted and removed at runtime.
This makes sdp3430_twl_gpio_setup() callable at runtime, and prevents
it being marked with an __init annotation.
As it calls omap2_hsmmc_init() unconditionally, the only resolution to
this warning is to remove the __init markings from omap2_hsmmc_init()
and its called functions. This addresses the functions in hsmmc.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xb798): Section mismatch in reference from the function omap_4430sdp_display_init() to the function .init.text:omap_display_init()
The function omap_4430sdp_display_init() references
the function __init omap_display_init().
This is often because omap_4430sdp_display_init lacks a __init
annotation or the annotation of omap_display_init is wrong.
Fix this by adding __init to omap_4430sdp_display_init().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: vmlinux.o(.text+0x1c664): Section mismatch in reference from the function omap_secondary_startup() to the function .cpuinit.text:secondary_startup()
The function omap_secondary_startup() references
the function __cpuinit secondary_startup().
This is often because omap_secondary_startup lacks a __cpuinit
annotation or the annotation of secondary_startup is wrong.
Unfortunately, fixing this causes a new warning which is harder to
solve:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x5328): Section mismatch in reference from the function omap4_hotplug_cpu() to the function .cpuinit.text:omap_secondary_startup()
The function omap4_hotplug_cpu() references
the function __cpuinit omap_secondary_startup().
This is often because omap4_hotplug_cpu lacks a __cpuinit
annotation or the annotation of omap_secondary_startup is wrong.
because omap4_hotplug_cpu() is used by power management code as well,
which may not end up using omap_secondary_startup().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Found by review.
omap4_sdp4430_wifi_mux_init() is called by an __init marked function,
and only calls omap_mux_init_gpio() and omap_mux_init_signal() which
are both also an __init marked functions.
The only reason this doesn't issue a warning is because the compiler
inlines omap4_sdp4430_wifi_mux_init() into omap4_sdp4430_wifi_init().
So, lets add the __init annotation to ensure this remains safe should
the compiler choose not to inline.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x15a4): Section mismatch in reference from the function omap_mux_init_signals() to the function .init.text:omap_mux_init_signal()
The function omap_mux_init_signals() references
the function __init omap_mux_init_signal().
This is often because omap_mux_init_signals lacks a __init
annotation or the annotation of omap_mux_init_signal is wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
WARNING: drivers/mfd/built-in.o(.devinit.text+0x258): Section mismatch in reference from the function twl_probe() to the function .init.text:twl4030_power_init()
The function __devinit twl_probe() references
a function __init twl4030_power_init().
If twl4030_power_init is only used by twl_probe then
annotate twl4030_power_init with a matching annotation.
twl4030_power_init() references other __init marked functions, so
these too must become __devinit.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
On my OMAP4 platform, I'm getting this error message repeated several
times at boot:
omap_vc_i2c_init: I2C config for all channels must match.
omap_vc_i2c_init: I2C config for all channels must match.
This doesn't help identify what the problem is. Fix this message to
be more informative:
omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).
omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).
This allows us to identify which voltage domains have a problem, and
what the I2C configuration state (a boolean, i2c_high_speed) setting
being used actually is.
From this we find that omap4_core_pmic has i2c_high_speed false, but
omap4_iva_pmic and omap4_mpu_pmic both have it set true.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
While testing on my OMAP3430 platform, this error message was emitted:
omap_vc_init_channel: PMIC info requried to configure vc forvdd_core not populated.Hence cannot initialize vc
Trying to find this message was difficult because it was wrapped across
several lines. It also mis-spells "required", doesn't read very well,
and has spaces lacking. Let's replace it with a more concise:
omap_vc_init_channel: No PMIC info for vdd_core
While we're here, fix a simple spelling error in a comment.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When CONFIG_OF is disabled, the compile fails with:
arch/arm/mach-omap2/prm44xx.c:41: error: 'OMAP44XX_IRQ_PRCM' undeclared here (not in a function)
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When eSDHC module is enabled on P5020/P3041/P2041/P1010 with eSDHC
version 2.3, there is following errors:
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
mmc0: Timeout waiting for hardware interrupt.
mmc0: error -110 whilst initialising SD card
mmc0: Unexpected interrupt 0x02000000.
It is because eSDHC controller has different bit setting for PROCTL
register at 0x28 comparing SD specification.
This patch sets DMAS bits correctly for byte operation and does not
change the default value of other field of PROCTL register.
For other FSL chips, such as MPC8536/P2020, PROCTL[DMAS]
bits are reserved and even if they are set to wrong bits, it will not
take effective.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Says Jens:
"Time to push off some of the pending items. I really wanted to wait
until we had the regression nailed, but alas it's not quite there yet.
But I'm very confident that it's "just" a missing expire on exit, so
fix from Tejun should be fairly trivial. I'm headed out for a week on
the slopes.
- Killing the barrier part of mtip32xx. It doesn't really support
barriers, and it doesn't need them (writes are fully ordered).
- A few fixes from Dan Carpenter, preventing overflows of integer
multiplication.
- A fixup for loop, fixing a previous commit that didn't quite solve
the partial read problem from Dave Young.
- A bio integer overflow fix from Kent Overstreet.
- Improvement/fix of the door "keep locked" part of the cdrom shared
code from Paolo Benzini.
- A few cfq fixes from Shaohua Li.
- A fix for bsg sysfs warning when removing a file it did not create
from Stanislaw Gruszka.
- Two fixes for floppy from Vivek, preventing a crash.
- A few block core fixes from Tejun. One killing the over-optimized
ioc exit path, cleaning that up nicely. Two others fixing an oops
on elevator switch, due to calling into the scheduler merge check
code without holding the queue lock."
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix lockdep warning on io_context release put_io_context()
relay: prevent integer overflow in relay_open()
loop: zero fill bio instead of return -EIO for partial read
bio: don't overflow in bio_get_nr_vecs()
floppy: Fix a crash during rmmod
floppy: Cleanup disk->queue before caling put_disk() if add_disk() was never called
cdrom: move shared static to cdrom_device_info
bsg: fix sysfs link remove warning
block: don't call elevator callbacks for plug merges
block: separate out blk_rq_merge_ok() and blk_try_merge() from elevator functions
mtip32xx: removed the irrelevant argument of mtip_hw_submit_io() and the unused member of struct driver_data
block: strip out locking optimization in put_io_context()
cdrom: use copy_to_user() without the underscores
block: fix ioc locking warning
block: fix NULL icq_cache reference
block,cfq: change code order
|
|
11a3122f6c "block: strip out locking optimization in put_io_context()"
removed ioc_lock depth lockdep annoation along with locking
optimization; however, while recursing from put_io_context() is no
longer possible, ioc_release_fn() may still end up putting the last
reference of another ioc through elevator, which wlil grab ioc->lock
triggering spurious (as the ioc is always different one) A-A deadlock
warning.
As this can only happen one time from ioc_release_fn(), using non-zero
subclass from ioc_release_fn() is enough. Use subclass 1.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
|
|
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix a bug which introduced by commit ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the netprio_cgroup module is not loaded, net_prio_subsys_id
is -1, and so sock_update_prioidx() accesses cgroup_subsys array
with negative index subsys[-1].
Make the code resembles cls_cgroup code, which is bug free.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So we delay the allocation till the priority is set through cgroup,
and this makes skb_update_priority() faster when it's not set.
This also eliminates an off-by-one bug similar with the one fixed
in the previous patch.
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
# mount -t cgroup xxx /mnt
# mkdir /mnt/tmp
# cat /mnt/tmp/net_prio.ifpriomap
lo 0
eth0 0
virbr0 0
# echo 'lo 999' > /mnt/tmp/net_prio.ifpriomap
# cat /mnt/tmp/net_prio.ifpriomap
lo 999
eth0 0
virbr0 4101267344
We got weired output, because we exceeded the boundary of the array.
We may even crash the kernel..
Origionally-authored-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop reusing dquots from the freelist when allocating new ones directly, and
implement a shrinker that actually follows the specifications for the
interface. The shrinker implementation is still highly suboptimal at this
point, but we can gradually work on it.
This also fixes an bug in the previous lock ordering, where we would take
the hash and dqlist locks inside of the freelist lock against the normal
lock ordering. This is only solvable by introducing the dispose list,
and thus not when using direct reclaim of unused dquots for new allocations.
As a side-effect the quota upper bound and used to free ratio values in
/proc/fs/xfs/xqm are set to 0 as these values don't make any sense in the
new world order.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ben Myers <bpm@sgi.com>
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/radeon: do not continue after error from r600_ib_test
drivers/gpu/drm/drm_ioc32.c: initialize all fields
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
fix 1 mysterious divide error
fix 3 NULL dereference bugs in writeback tracing, on SD card removal w/o umount
* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: fix dereferencing NULL bdi->dev on trace_writeback_queue
lib: proportion: lower PROP_MAX_SHIFT to 32 on 64-bit kernel
writeback: fix NULL bdi->dev in trace writeback_single_inode
backing-dev: fix wakeup timer races with bdi_unregister()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix double start/stop in x86_pmu_start()
perf evsel: Fix an issue where perf report fails to show the proper percentage
perf tools: Fix prefix matching for kernel maps
perf tools: Fix perf stack to non executable on x86_64
perf: Remove deprecated WARN_ON_ONCE()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Couple of regressions, couple of zero-day bugs, a minor enhancement.
Nothing really major.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (f75375s) Let f75375_update_device treat pwmX as a measured value
hwmon: (f75375s) Fix bit shifting in f75375_write16
hwmon: (f75375s) Fix reading of wrong register when initializing the F75387
hwmon: (f75375s) Fix automatic pwm mode setting for F75373 & F75375
hwmon: (w83627ehf) Remove duplicate code
|
|
Current code takes wrong parameter while calling max8649_list_voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux into drm-fixes
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux:
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT (v2)
drm/i915: no lvds quirk for AOpen MP45
drm/i915: Force explicit bpp selection for intel_dp_link_required
drm/i915: fixup interlaced bits clearing in PIPECONF on PCH_SPLIT
drm/i915:: Disable FBC on SandyBridge
|
