Age | Commit message (Collapse) | Author | Files | Lines |
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Here's the one lonely bugfix I talked about on irc.
* tag 'drm-misc-fixes-2016-12-22' of git://anongit.freedesktop.org/git/drm-misc:
drivers/gpu/drm/ast: Fix infinite loop if read fails
|
|
into drm-fixes
- fix display regression on DCE6/8
- Powergating fixes for GFX8
- amdgpu SI fixes (golden settings, proper rev id setup, etc.)
* 'drm-next-4.10' of git://people.freedesktop.org/~agd5f/linux: (21 commits)
drm/amdgpu: update tile table for oland/hainan
drm/amdgpu: update tile table for verde
drm/amdgpu: update rev id for verde
drm/amdgpu: update golden setting for verde
drm/amdgpu: update rev id for oland
drm/amdgpu: update golden setting for oland
drm/amdgpu: update rev id for hainan
drm/amdgpu: update golden setting for hainan
drm/amdgpu: update rev id for pitcairn
drm/amdgpu: update golden setting for pitcairn
drm/amdgpu: update golden setting/tiling table of tahiti
drm/amdgpu: fix cursor setting of dce6/dce8
drm/amdgpu: refine set clock gating for tonga/polaris
drm/amdgpu: initialize cg flags for tonga/polaris10/polaris11.
drm/amdgpu: add new gfx cg flags.
drm/amdgpu: fix pg can't be disabled by PG mask.
drm/amdgpu: always initialize gfx pg for gfx_v8.0.
drm/amdgpu: enable AMD_PG_SUPPORT_CP in Carrizo/Stoney.
drm/amdgpu: fix init save/restore list in gfx_v8.0
drm/amdgpu: fix enable_cp_power_gating in gfx_v8.0.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED maintainer email update from Jacek Anaszewski:
"Update Jacek Anaszewski's email address"
* tag 'leds_for_4.10_email_update' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Update Jacek Anaszewski's email address
|
|
Pull block layer fixes from Jens Axboe:
"Just a set of small fixes that have either been queued up after the
original pull for this merge window, or just missed the original pull
request.
- a few bcache fixes/changes from Eric and Kent
- add WRITE_SAME to the command filter whitelist frm Mauricio
- kill an unused struct member from Ritesh
- partition IO alignment fix from Stefan
- nvme sysfs printf fix from Stephen"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: check partition alignment
nvme : Use correct scnprintf in cmb show
block: allow WRITE_SAME commands with the SG_IO ioctl
block: Remove unused member (busy) from struct blk_queue_tag
bcache: partition support: add 16 minors per bcacheN device
bcache: Make gc wakeup sane, remove set_task_state()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Here are new versions of two ACPICA changes that were deferred
previously due to a problem they had introduced, two cleanups on top
of them and the removal of a useless warning message from the ACPI
core.
Specifics:
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng)
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui)"
* tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
ACPI: do not warn if _BQC does not exist
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"They fix one bug introduced recently, a build warning and a kerneldoc
function description.
Specifics:
- Prevent the acpi-cpufreq driver from crashing on exit by fixing a
check against the __cpuhp_setup_state() return value and fix the
kerneldoc description of that function to make it clear that it may
return positive numbers on success too (Boris Ostrovsky)
- Drop an incorrect __init annotation of a function in the s3c64xx
cpufreq driver and fix a build warning generated (by older
compilers) because of it (Arnd Bergmann)"
* tag 'pm-fixes-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: s3c64xx: remove incorrect __init annotation
cpufreq: Remove CPU hotplug callbacks only if they were initialized
CPU/hotplug: Clarify description of __cpuhp_setup_state() return value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- further fix thread wake-up for requests
- use a bounce buffer to fix DMA issue for SSR register read
MMC host:
- sdhci: Fix a regression for runtime PM
- sdhci-cadence: Add a proper SoC specific DT compatible"
* tag 'mmc-v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sd: Meet alignment requirements for raw_ssr DMA
mmc: core: Further fix thread wake-up
mmc: sdhci: Fix to handle MMC_POWER_UNDEFINED
mmc: sdhci-cadence: add Socionext UniPhier specific compatible string
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull SElinux fix from James Morris:
"From Paul:
'A small SELinux patch to fix some clang/llvm compiler warnings and
ensure the tools under scripts work well in the face of kernel
changes'"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: use the kernel headers when building scripts/selinux
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cache allocation interface from Thomas Gleixner:
"This provides support for Intel's Cache Allocation Technology, a cache
partitioning mechanism.
The interface is odd, but the hardware interface of that CAT stuff is
odd as well.
We tried hard to come up with an abstraction, but that only allows
rather simple partitioning, but no way of sharing and dealing with the
per package nature of this mechanism.
In the end we decided to expose the allocation bitmaps directly so all
combinations of the hardware can be utilized.
There are two ways of associating a cache partition:
- Task
A task can be added to a resource group. It uses the cache
partition associated to the group.
- CPU
All tasks which are not member of a resource group use the group to
which the CPU they are running on is associated with.
That allows for simple CPU based partitioning schemes.
The main expected user sare:
- Virtualization so a VM can only trash only the associated part of
the cash w/o disturbing others
- Real-Time systems to seperate RT and general workloads.
- Latency sensitive enterprise workloads
- In theory this also can be used to protect against cache side
channel attacks"
[ Intel RDT is "Resource Director Technology". The interface really is
rather odd and very specific, which delayed this pull request while I
was thinking about it. The pull request itself came in early during
the merge window, I just delayed it until things had calmed down and I
had more time.
But people tell me they'll use this, and the good news is that it is
_so_ specific that it's rather independent of anything else, and no
user is going to depend on the interface since it's pretty rare. So if
push comes to shove, we can just remove the interface and nothing will
break ]
* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
x86/intel_rdt: Implement show_options() for resctrlfs
x86/intel_rdt: Call intel_rdt_sched_in() with preemption disabled
x86/intel_rdt: Update task closid immediately on CPU in rmdir and unmount
x86/intel_rdt: Fix setting of closid when adding CPUs to a group
x86/intel_rdt: Update percpu closid immeditately on CPUs affected by changee
x86/intel_rdt: Reset per cpu closids on unmount
x86/intel_rdt: Select KERNFS when enabling INTEL_RDT_A
x86/intel_rdt: Prevent deadlock against hotplug lock
x86/intel_rdt: Protect info directory from removal
x86/intel_rdt: Add info files to Documentation
x86/intel_rdt: Export the minimum number of set mask bits in sysfs
x86/intel_rdt: Propagate error in rdt_mount() properly
x86/intel_rdt: Add a missing #include
MAINTAINERS: Add maintainer for Intel RDT resource allocation
x86/intel_rdt: Add scheduler hook
x86/intel_rdt: Add schemata file
x86/intel_rdt: Add tasks files
x86/intel_rdt: Add cpus file
x86/intel_rdt: Add mkdir to resctrl file system
x86/intel_rdt: Add "info" files to resctrl file system
...
|
|
My previous email address is no longer valid.
From now on, jacek.anaszewski@gmail.com should be used instead.
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
* pm-cpufreq:
cpufreq: s3c64xx: remove incorrect __init annotation
cpufreq: Remove CPU hotplug callbacks only if they were initialized
CPU/hotplug: Clarify description of __cpuhp_setup_state() return value
|
|
* acpica:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
* acpi-scan:
ACPI: do not warn if _BQC does not exist
|
|
This address hasn't been accurate for several years now.
Simply remove it.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 8924feff66f3 ("splice: lift pipe_lock out of splice_to_pipe()")
caused a regression when there were no more readers left on a pipe that
was being spliced into: rather than the expected SIGPIPE and -EPIPE
return value, the writer would end up waiting forever for space to free
up (which obviously was not going to happen with no readers around).
Fixes: 8924feff66f3 ("splice: lift pipe_lock out of splice_to_pipe()")
Reported-and-tested-by: Andreas Schwab <schwab@linux-m68k.org>
Debugged-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # v4.9
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
- add Kernel address space layout randomization support
- re-enable interrupts earlier now that we have a working IRQ stack
- optimize the timer interrupt function to better cope with missed
timer irqs
- fix error return code in parisc perf code (by Dan Carpenter)
- fix PAT debug code
* 'parisc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Optimize timer interrupt function
parisc: perf: return -EFAULT on error
parisc: Enhance CPU detection code on PAT machines
parisc: Re-enable interrupts early
parisc: Enable KASLR
|
|
Pull more NFS client updates from Trond Myklebust:
"Highlights include:
- further attribute cache improvements to make revalidation more fine
grained
- NFSv4 locking improvements
Bugfixes:
- nfs4_fl_prepare_ds must be careful about reporting success in files
layout
- pNFS/flexfiles: Instead of marking a device inactive, remove it
from the cache"
* tag 'nfs-for-4.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Retry the DELEGRETURN if the embedded GETATTR is rejected with EACCES
NFS: Retry the CLOSE if the embedded GETATTR is rejected with EACCES
NFSv4: Place the GETATTR operation before the CLOSE
NFSv4: Also ask for attributes when downgrading to a READ-only state
NFS: Don't abuse NFS_INO_REVAL_FORCED in nfs_post_op_update_inode_locked()
pNFS: Return RW layouts on OPEN_DOWNGRADE
NFSv4: Add encode/decode of the layoutreturn op in OPEN_DOWNGRADE
NFS: Don't disconnect open-owner on NFS4ERR_BAD_SEQID
NFSv4: ensure __nfs4_find_lock_state returns consistent result.
NFSv4.1: nfs4_fl_prepare_ds must be careful about reporting success.
pNFS/flexfiles: delete deviceid, don't mark inactive
NFS: Clean up nfs_attribute_timeout()
NFS: Remove unused function nfs_revalidate_inode_rcu()
NFS: Fix and clean up the access cache validity checking
NFS: Only look at the change attribute cache state in nfs_weak_revalidate()
NFS: Clean up cache validity checking
NFS: Don't revalidate the file on close if we hold a delegation
NFSv4: Don't discard the attributes returned by asynchronous DELEGRETURN
NFSv4: Update the attribute cache info in update_changeattr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux
Pull scsi target cleanups from Bart Van Assche:
"The changes here are:
- a few small bug fixes for the iSCSI and user space target drivers.
- minimize the target build time by about 30% by rearranging #include
directives
- fix the second argument passed to percpu_ida_alloc()
- reduce the number of false positive warnings reported by sparse
These patches pass Wu Fengguang's build bot tests and also the
linux-next tests"
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
iscsi-target: Return error if unable to add network portal
target: Fix spelling mistake and unwrap multi-line text
target/iscsi: Fix double free in lio_target_tiqn_addtpg()
target/user: Fix use-after-free of tcmu_cmds if they are expired
target: Minimize #include directives
target/user: Add an #include directive
cxgbit: Add an #include directive
ibmvscsi_tgt: Add two #include directives
sbp-target: Add an #include directive
qla2xxx: Add an #include directive
configfs: Minimize #include directives
usb: gadget: Fix second argument of percpu_ida_alloc()
sbp-target: Fix second argument of percpu_ida_alloc()
target/user: Fix a data type in tcmu_queue_cmd()
target: Use NULL instead of 0 to represent a pointer
|
|
This reverts commit 16200948d8353fe29a473a394d7d26790deae0e7.
The commit was intended to cover the race condition, but it introduced
yet another regression for devices with the implicit feedback, leading
to a kernel panic due to NULL-dereference in an irq context.
As the race condition that was addressed by the commit is very rare
and the regression is much worse, let's revert the commit for rc1, and
fix the issue properly in a later patch.
Fixes: 16200948d835 ("ALSA: usb-audio: Fix race at stopping the stream")
Reported-by: Ioan-Adrian Ratiu <adi@adirat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 3322d0d64f4e ("selinux: keep SELinux in sync with new capability
definitions") added a check on the defined capabilities without
explicitly including the capability header file which caused problems
when building genheaders for users of clang/llvm. Resolve this by
using the kernel headers when building genheaders, which is arguably
the right thing to do regardless, and explicitly including the
kernel's capability.h header file in classmap.h. We also update the
mdp build, even though it wasn't causing an error we really should
be using the headers from the kernel we are building.
Reported-by: Nicolas Iooss <nicolas.iooss@m4x.org>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
The mmc_read_ssr() function results in DMA to the raw_ssr member of
struct mmc_card, which is not guaranteed to be cache line aligned & thus
might not meet the requirements set out in Documentation/DMA-API.txt:
Warnings: Memory coherency operates at a granularity called the cache
line width. In order for memory mapped by this API to operate
correctly, the mapped region must begin exactly on a cache line
boundary and end exactly on one (to prevent two separately mapped
regions from sharing a single cache line). Since the cache line size
may not be known at compile time, the API will not enforce this
requirement. Therefore, it is recommended that driver writers who
don't take special care to determine the cache line size at run time
only map virtual regions that begin and end on page boundaries (which
are guaranteed also to be cache line boundaries).
On some systems where DMA is non-coherent this can lead to us losing
data that shares cache lines with the raw_ssr array.
Fix this by kmalloc'ing a temporary buffer to perform DMA into. kmalloc
will ensure the buffer is suitably aligned, allowing the DMA to be
performed without any loss of data.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 5275a652d296 ("mmc: sd: Export SD Status via “ssr” device attribute")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
s3c64xx_cpufreq_config_regulator is incorrectly annotated
as __init, since the caller is also not init:
WARNING: vmlinux.o(.text+0x92fe1c): Section mismatch in reference from the function s3c64xx_cpufreq_driver_init() to the function .init.text:s3c64xx_cpufreq_config_regulator()
With modern gcc versions, the function gets inline, so we don't
see the warning, this only happens with gcc-4.6 and older.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since CPU hotplug callbacks are requested for CPUHP_AP_ONLINE_DYN state,
successful callback initialization will result in cpuhp_setup_state()
returning a positive value. Therefore acpi_cpufreq_online being zero
indicates that callbacks have not been installed.
This means that acpi_cpufreq_boost_exit() should only remove them if
acpi_cpufreq_online is positive. Trying to call
cpuhp_remove_state_nocalls(0) will cause a BUG().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When ivoked with CPUHP_AP_ONLINE_DYN state __cpuhp_setup_state()
is expected to return positive value which is the hotplug state that
the routine assigns.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
acpi_get_table_with_size()/early_acpi_os_unmap_memory()
Since all users are cleaned up, remove the 2 deprecated APIs due to no
users.
As a Linux variable rather than an ACPICA variable, acpi_gbl_permanent_mmap
is renamed to acpi_permanent_mmap to have a consistent coding style across
entire Linux ACPI subsystem.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch removes the users of the deprectated APIs:
acpi_get_table_with_size()
early_acpi_os_unmap_memory()
The following APIs should be used instead of:
acpi_get_table()
acpi_put_table()
The deprecated APIs are invented to be a replacement of acpi_get_table()
during the early stage so that the early mapped pointer will not be stored
in ACPICA core and thus the late stage acpi_get_table() won't return a
wrong pointer. The mapping size is returned just because it is required by
early_acpi_os_unmap_memory() to unmap the pointer during early stage.
But as the mapping size equals to the acpi_table_header.length
(see acpi_tb_init_table_descriptor() and acpi_tb_validate_table()), when
such a convenient result is returned, driver code will start to use it
instead of accessing acpi_table_header to obtain the length.
Thus this patch cleans up the drivers by replacing returned table size with
acpi_table_header.length, and should be a no-op.
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit d98de9ca14891130efc5dcdc871b97eb27b4b0f5
FADT parsing code requires FADT to be installed as
ACPI_TABLE_ORIGIN_INTERNAL_PHYSICAL, using new
acpi_tb_get_table()/acpi_tb_put_table(), other address types can also be allowed,
thus facilitates FADT customization with virtual address. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/d98de9ca
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
early_acpi_os_unmap_memory() from Linux kernel
ACPICA commit cac6790954d4d752a083e6122220b8a22febcd07
This patch back ports Linux acpi_get_table_with_size() and
early_acpi_os_unmap_memory() into ACPICA upstream to reduce divergences.
The 2 APIs are used by Linux as table management APIs for long time, it
contains a hidden logic that during the early stage, the mapped tables
should be unmapped before the early stage ends.
During the early stage, tables are handled by the following sequence:
acpi_get_table_with_size();
parse the table
early_acpi_os_unmap_memory();
During the late stage, tables are handled by the following sequence:
acpi_get_table();
parse the table
Linux uses acpi_gbl_permanent_mmap to distinguish the early stage and the
late stage.
The reasoning of introducing acpi_get_table_with_size() is: ACPICA will
remember the early mapped pointer in acpi_get_table() and Linux isn't able to
prevent ACPICA from using the wrong early mapped pointer during the late
stage as there is no API provided from ACPICA to be an inverse of
acpi_get_table() to forget the early mapped pointer.
But how ACPICA can work with the early/late stage requirement? Inside of
ACPICA, tables are ensured to be remained in "INSTALLED" state during the
early stage, and they are carefully not transitioned to "VALIDATED" state
until the late stage. So the same logic is in fact implemented inside of
ACPICA in a different way. The gap is only that the feature is not provided
to the OSPMs in an accessible external API style.
It then is possible to fix the gap by providing an inverse of
acpi_get_table() from ACPICA, so that the two Linux sequences can be
combined:
acpi_get_table();
parse the table
acpi_put_table();
In order to work easier with the current Linux code, acpi_get_table() and
acpi_put_table() is implemented in a usage counting based style:
1. When the usage count of the table is increased from 0 to 1, table is
mapped and .Pointer is set with the mapping address (VALIDATED);
2. When the usage count of the table is decreased from 1 to 0, .Pointer
is unset and the mapping address is unmapped (INVALIDATED).
So that we can deploy the new APIs to Linux with minimal effort by just
invoking acpi_get_table() in acpi_get_table_with_size() and invoking
acpi_put_table() in early_acpi_os_unmap_memory(). Lv Zheng.
Link: https://github.com/acpica/acpica/commit/cac67909
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Pull networking fixes and cleanups from David Miller:
1) Use rb_entry() instead of hardcoded container_of(), from Geliang
Tang.
2) Use correct memory barriers in stammac driver, from Pavel Machek.
3) Fix assoc bind address handling in SCTP, from Xin Long.
4) Make the length check for UFO handling consistent between
__ip_append_data() and ip_finish_output(), from Zheng Li.
5) HSI driver compatible strings were busted fro hix5hd2, from Dongpo
Li.
6) Handle devm_ioremap() errors properly in cavium driver, from Arvind
Yadav.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
RDS: use rb_entry()
net_sched: sch_netem: use rb_entry()
net_sched: sch_fq: use rb_entry()
net/mlx5: use rb_entry()
ethernet: sfc: Add Kconfig entry for vendor Solarflare
sctp: not copying duplicate addrs to the assoc's bind address list
sctp: reduce indent level in sctp_copy_local_addr_list
ARM: dts: hix5hd2: don't change the existing compatible string
net: hix5hd2_gmac: fix compatible strings name
openvswitch: Add a missing break statement.
net: netcp: ethss: fix 10gbe host port tx pri map configuration
net: netcp: ethss: fix errors in ethtool ops
fsl/fman: enable compilation on ARM64
fsl/fman: A007273 only applies to PPC SoCs
powerpc: fsl/fman: remove fsl,fman from of_device_ids[]
fsl/fman: fix 1G support for QSGMII interfaces
dt: bindings: net: use boolean dt properties for eee broken modes
net: phy: use boolean dt properties for eee broken modes
net: phy: fix sign type error in genphy_config_eee_advert
ipv4: Should use consistent conditional judgement for ip fragment in __ip_append_data and ip_finish_output
...
|
|
Merge final set of updates from Andrew Morton:
- a series to make IMA play better across kexec
- a handful of random fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
printk: fix typo in CONSOLE_LOGLEVEL_DEFAULT help text
ratelimit: fix WARN_ON_RATELIMIT return value
kcov: make kcov work properly with KASLR enabled
arm64: setup: introduce kaslr_offset()
mm: fadvise: avoid expensive remote LRU cache draining after FADV_DONTNEED
ima: platform-independent hash value
ima: define a canonical binary_runtime_measurements list format
ima: support restoring multiple template formats
ima: store the builtin/custom template definitions in a list
ima: on soft reboot, save the measurement list
powerpc: ima: send the kexec buffer to the next kernel
ima: maintain memory size needed for serializing the measurement list
ima: permit duplicate measurement list entries
ima: on soft reboot, restore the measurement list
powerpc: ima: get the kexec buffer passed by the previous kernel
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- new features (poll and SRAM usage) added to the mailbox-test driver
- major update of Broadcom's PDC controller driver
- minor fix for auto-loading test and STI driver modules
* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: mailbox-test: allow reserved areas in SRAM
mailbox: mailbox-test: add support for fasync/poll
mailbox: bcm-pdc: Remove unnecessary void* casts
mailbox: bcm-pdc: Simplify interrupt handler logic
mailbox: bcm-pdc: Performance improvements
mailbox: bcm-pdc: Don't use iowrite32 to write DMA descriptors
mailbox: bcm-pdc: Convert from threaded IRQ to tasklet
mailbox: bcm-pdc: Try to improve branch prediction
mailbox: bcm-pdc: streamline rx code
mailbox: bcm-pdc: Convert from interrupts to poll for tx done
mailbox: bcm-pdc: PDC driver leaves debugfs files after removal
mailbox: bcm-pdc: Changes so mbox client can be removed / re-inserted
mailbox: bcm-pdc: Use octal permissions rather than symbolic
mailbox: sti: Fix module autoload for OF registration
mailbox: mailbox-test: Fix module autoload
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang.
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mux: mlxcpld: fix i2c mux selection caching
i2c: designware: fix wrong Tx/Rx FIFO for ACPI
i2c: xgene: Fix missing code of DTB support
i2c: mux: pca954x: fix i2c mux selection caching
i2c: octeon: thunderx: Limit register access retries
|
|
Pull documentation fix from Jonathan Corbet:
"A single fix for the build system.
It would appear that the docutils developers, in their wisdom, broke
the API in the 0.13 release. This fix detects the breakage and allows
the docs to be built with both the old and new versions"
* tag 'doc-4.10-3' of git://git.lwn.net/linux:
docs: sphinx-extensions: make rstFlatTable work with docutils 0.13
|
|
Pull arch/microblaze updates from Michal Simek:
- wire-up new syscalls
- add new codes and fpga families
- fix a return value
* tag 'microblaze-4.10-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Add new fpga families
microblaze: Add missing release version code v9.6 and v10
microblaze: Add missing syscalls
microblaze: Fix return value from xilinx_timer_init
|
|
Pull Xtensa updates from Max Filippov:
- enable HAVE_DMA_CONTIGUOUS, configure shared DMA pool reservation in
kc705 DTS
- update xtensa DMA-related Documentation/features entries
- clean up arch/xtensa/kernel/setup.c: move S32C1I self-test out of it,
remove unused declarations, fix screen_info definition
* tag 'xtensa-20161219' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: update DMA-related Documentation/features entries
xtensa: configure shared DMA pool reservation in kc705 DTS
xtensa: enable HAVE_DMA_CONTIGUOUS
xtensa: move S32C1I self-test to a separate file
xtensa: fix screen_info, clean up unused declarations in setup.c
|
|
Restructure the timer interrupt function to better cope with missed timer irqs.
Optimize the calculation when the next interrupt should happen and skip irqs if
they would happen too shortly after exit of the irq function.
The update_process_times() call is done anyway at every timer irq, so we can
safely drop the prof_counter and prof_multiplier variables from the per_cpu
structure.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|