summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/ata/ahci_xgene.c48
1 files changed, 34 insertions, 14 deletions
diff --git a/drivers/ata/ahci_xgene.c b/drivers/ata/ahci_xgene.c
index 37501fd0973d..f03aab187f4d 100644
--- a/drivers/ata/ahci_xgene.c
+++ b/drivers/ata/ahci_xgene.c
@@ -78,6 +78,9 @@
#define CFG_MEM_RAM_SHUTDOWN 0x00000070
#define BLOCK_MEM_RDY 0x00000074
+/* Max retry for link down */
+#define MAX_LINK_DOWN_RETRY 3
+
struct xgene_ahci_context {
struct ahci_host_priv *hpriv;
struct device *dev;
@@ -237,8 +240,11 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel)
* and Gen1 (1.5Gbps). Otherwise during long IO stress test, the PHY will
* report disparity error and etc. In addition, during COMRESET, there can
* be error reported in the register PORT_SCR_ERR. For SERR_DISPARITY and
- * SERR_10B_8B_ERR, the PHY receiver line must be reseted. The following
- * algorithm is followed to proper configure the hardware PHY during COMRESET:
+ * SERR_10B_8B_ERR, the PHY receiver line must be reseted. Also during long
+ * reboot cycle regression, sometimes the PHY reports link down even if the
+ * device is present because of speed negotiation failure. so need to retry
+ * the COMRESET to get the link up. The following algorithm is followed to
+ * proper configure the hardware PHY during COMRESET:
*
* Alg Part 1:
* 1. Start the PHY at Gen3 speed (default setting)
@@ -254,9 +260,15 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel)
* Alg Part 2:
* 1. On link up, if there are any SERR_DISPARITY and SERR_10B_8B_ERR error
* reported in the register PORT_SCR_ERR, then reset the PHY receiver line
- * 2. Go to Alg Part 3
+ * 2. Go to Alg Part 4
*
* Alg Part 3:
+ * 1. Check the PORT_SCR_STAT to see whether device presence detected but PHY
+ * communication establishment failed and maximum link down attempts are
+ * less than Max attempts 3 then goto Alg Part 1.
+ * 2. Go to Alg Part 4.
+ *
+ * Alg Part 4:
* 1. Clear any pending from register PORT_SCR_ERR.
*
* NOTE: For the initial version, we will NOT support Gen1/Gen2. In addition
@@ -275,19 +287,27 @@ static int xgene_ahci_do_hardreset(struct ata_link *link,
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
void __iomem *port_mmio = ahci_port_base(ap);
struct ata_taskfile tf;
+ int link_down_retry = 0;
int rc;
- u32 val;
-
- /* clear D2H reception area to properly wait for D2H FIS */
- ata_tf_init(link->device, &tf);
- tf.command = ATA_BUSY;
- ata_tf_to_fis(&tf, 0, 0, d2h_fis);
- rc = sata_link_hardreset(link, timing, deadline, online,
+ u32 val, sstatus;
+
+ do {
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = ATA_BUSY;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+ rc = sata_link_hardreset(link, timing, deadline, online,
ahci_check_ready);
-
- val = readl(port_mmio + PORT_SCR_ERR);
- if (val & (SERR_DISPARITY | SERR_10B_8B_ERR))
- dev_warn(ctx->dev, "link has error\n");
+ if (*online) {
+ val = readl(port_mmio + PORT_SCR_ERR);
+ if (val & (SERR_DISPARITY | SERR_10B_8B_ERR))
+ dev_warn(ctx->dev, "link has error\n");
+ break;
+ }
+
+ sata_scr_read(link, SCR_STATUS, &sstatus);
+ } while (link_down_retry++ < MAX_LINK_DOWN_RETRY &&
+ (sstatus & 0xff) == 0x1);
/* clear all errors if any pending */
val = readl(port_mmio + PORT_SCR_ERR);