diff options
Diffstat (limited to 'arch/arm/mach-omap2/board-h4.c')
| -rw-r--r-- | arch/arm/mach-omap2/board-h4.c | 61 |
1 files changed, 32 insertions, 29 deletions
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index 0665f2c8dc8e..e09bd686389f 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -33,7 +33,6 @@ #include <plat/control.h> #include <mach/gpio.h> -#include <plat/mux.h> #include <plat/usb.h> #include <plat/board.h> #include <plat/common.h> @@ -42,6 +41,8 @@ #include <plat/dma.h> #include <plat/gpmc.h> +#include "mux.h" + #define H4_FLASH_CS 0 #define H4_SMC91X_CS 1 @@ -246,7 +247,7 @@ static inline void __init h4_init_debug(void) udelay(100); - omap_cfg_reg(M15_24XX_GPIO92); + omap_mux_init_gpio(92, 0); if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0) gpmc_cs_free(eth_cs); @@ -272,27 +273,6 @@ static struct omap_lcd_config h4_lcd_config __initdata = { }; static struct omap_usb_config h4_usb_config __initdata = { -#ifdef CONFIG_MACH_OMAP2_H4_USB1 - /* NOTE: usb1 could also be used with 3 wire signaling */ - .pins[1] = 4, -#endif - -#ifdef CONFIG_MACH_OMAP_H4_OTG - /* S1.10 ON -- USB OTG port - * usb0 switched to Mini-AB port and isp1301 transceiver; - * S2.POS3 = OFF, S2.POS4 = ON ... to allow battery charging - */ - .otg = 1, - .pins[0] = 4, -#ifdef CONFIG_USB_GADGET_OMAP - /* use OTG cable, or standard A-to-MiniB */ - .hmc_mode = 0x14, /* 0:dev/otg 1:host 2:disable */ -#elif defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) - /* use OTG cable, or NONSTANDARD (B-to-MiniB) */ - .hmc_mode = 0x11, /* 0:host 1:host 2:disable */ -#endif /* XX */ - -#else /* S1.10 OFF -- usb "download port" * usb0 switched to Mini-B port and isp1105 transceiver; * S2.POS3 = ON, S2.POS4 = OFF ... to enable battery charging @@ -301,7 +281,6 @@ static struct omap_usb_config h4_usb_config __initdata = { .pins[0] = 3, /* .hmc_mode = 0x14,*/ /* 0:dev 1:host 2:disable */ .hmc_mode = 0x00, /* 0:dev|otg 1:disable 2:disable */ -#endif }; static struct omap_board_config_kernel h4_config[] = { @@ -338,31 +317,54 @@ static struct i2c_board_info __initdata h4_i2c_board_info[] = { }, }; +#ifdef CONFIG_OMAP_MUX +static struct omap_board_mux board_mux[] __initdata = { + { .reg_offset = OMAP_MUX_TERMINATOR }, +}; +#else +#define board_mux NULL +#endif + static void __init omap_h4_init(void) { + omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAF); + /* * Make sure the serial ports are muxed on at this point. * You have to mux them off in device drivers later on * if not needed. */ -#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE) - omap_cfg_reg(K15_24XX_UART3_TX); - omap_cfg_reg(K14_24XX_UART3_RX); -#endif #if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE) + omap_mux_init_gpio(88, OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_gpio(89, OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_gpio(124, OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP); if (omap_has_menelaus()) { + omap_mux_init_signal("sdrc_a14.gpio0", + OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_signal("vlynq_rx0.gpio_15", 0); + omap_mux_init_signal("gpio_98", 0); row_gpios[5] = 0; col_gpios[2] = 15; col_gpios[6] = 18; + } else { + omap_mux_init_signal("gpio_96", OMAP_PULL_ENA | OMAP_PULL_UP); + omap_mux_init_signal("gpio_100", 0); + omap_mux_init_signal("gpio_98", 0); } + omap_mux_init_signal("gpio_90", 0); + omap_mux_init_signal("gpio_91", 0); + omap_mux_init_signal("gpio_36", 0); + omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0); + omap_mux_init_signal("gpio_97", 0); #endif i2c_register_board_info(1, h4_i2c_board_info, ARRAY_SIZE(h4_i2c_board_info)); platform_add_devices(h4_devices, ARRAY_SIZE(h4_devices)); - omap_usb_init(&h4_usb_config); + omap2_usbfs_init(&h4_usb_config); omap_serial_init(); } @@ -378,6 +380,7 @@ MACHINE_START(OMAP_H4, "OMAP2420 H4 board") .io_pg_offst = ((0xfa000000) >> 18) & 0xfffc, .boot_params = 0x80000100, .map_io = omap_h4_map_io, + .reserve = omap_reserve, .init_irq = omap_h4_init_irq, .init_machine = omap_h4_init, .timer = &omap_timer, |