diff options
Diffstat (limited to 'Documentation')
21 files changed, 496 insertions, 67 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 00bb04972612..5ab1089d1422 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -857,7 +857,7 @@ The filter can be disabled or changed to another driver later using sysfs. - drm_kms_helper.edid_firmware=[<connector>:]<file>[,[<connector>:]<file>] + drm.edid_firmware=[<connector>:]<file>[,[<connector>:]<file>] Broken monitors, graphic adapters, KVMs and EDIDless panels may send no or incorrect EDID data sets. This parameter allows to specify an EDID data sets diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 06668bca7ffc..0047b1394c70 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -68,6 +68,8 @@ Optional properties: - adi,disable-timing-generator: Only for ADV7533. Disables the internal timing generator. The chip will rely on the sync signals in the DSI data lanes, rather than generate its own timings for HDMI output. +- clocks: from common clock binding: reference to the CEC clock. +- clock-names: from common clock binding: must be "cec". Required nodes: @@ -89,6 +91,8 @@ Example reg = <39>; interrupt-parent = <&gpio3>; interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + clocks = <&cec_clock>; + clock-names = "cec"; adi,input-depth = <8>; adi,input-colorspace = "rgb"; diff --git a/Documentation/devicetree/bindings/display/bridge/sii9234.txt b/Documentation/devicetree/bindings/display/bridge/sii9234.txt new file mode 100644 index 000000000000..88041ba23d56 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/sii9234.txt @@ -0,0 +1,49 @@ +Silicon Image SiI9234 HDMI/MHL bridge bindings + +Required properties: + - compatible : "sil,sii9234". + - reg : I2C address for TPI interface, use 0x39 + - avcc33-supply : MHL/USB Switch Supply Voltage (3.3V) + - iovcc18-supply : I/O Supply Voltage (1.8V) + - avcc12-supply : TMDS Analog Supply Voltage (1.2V) + - cvcc12-supply : Digital Core Supply Voltage (1.2V) + - interrupts, interrupt-parent: interrupt specifier of INT pin + - reset-gpios: gpio specifier of RESET pin (active low) + - video interfaces: Device node can contain two video interface port + nodes for HDMI encoder and connector according to [1]. + - port@0 - MHL to HDMI + - port@1 - MHL to connector + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + + +Example: + sii9234@39 { + compatible = "sil,sii9234"; + reg = <0x39>; + avcc33-supply = <&vcc33mhl>; + iovcc18-supply = <&vcc18mhl>; + avcc12-supply = <&vsil12>; + cvcc12-supply = <&vsil12>; + reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpf3>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mhl_to_hdmi: endpoint { + remote-endpoint = <&hdmi_to_mhl>; + }; + }; + port@1 { + reg = <1>; + mhl_to_connector: endpoint { + remote-endpoint = <&connector_to_mhl>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/faraday,tve200.txt b/Documentation/devicetree/bindings/display/faraday,tve200.txt new file mode 100644 index 000000000000..82e3bc0b7485 --- /dev/null +++ b/Documentation/devicetree/bindings/display/faraday,tve200.txt @@ -0,0 +1,54 @@ +* Faraday TV Encoder TVE200 + +Required properties: + +- compatible: must be one of: + "faraday,tve200" + "cortina,gemini-tvc", "faraday,tve200" + +- reg: base address and size of the control registers block + +- interrupts: contains an interrupt specifier for the interrupt + line from the TVE200 + +- clock-names: should contain "PCLK" for the clock line clocking the + silicon and "TVE" for the 27MHz clock to the video driver + +- clocks: contains phandle and clock specifier pairs for the entries + in the clock-names property. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: + +- resets: contains the reset line phandle for the block + +Required sub-nodes: + +- port: describes LCD panel signals, following the common binding + for video transmitter interfaces; see + Documentation/devicetree/bindings/media/video-interfaces.txt + This port should have the properties: + reg = <0>; + It should have one endpoint connected to a remote endpoint where + the display is connected. + +Example: + +display-controller@6a000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "faraday,tve200"; + reg = <0x6a000000 0x1000>; + interrupts = <13 IRQ_TYPE_EDGE_RISING>; + resets = <&syscon GEMINI_RESET_TVC>; + clocks = <&syscon GEMINI_CLK_GATE_TVC>, + <&syscon GEMINI_CLK_TVC>; + clock-names = "PCLK", "TVE"; + + port@0 { + reg = <0>; + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index fa00e62e1cf6..a6671bd2c85a 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -13,16 +13,16 @@ Required properties: - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: Phandles to device clocks. - clock-names: the following clocks are required: - * "mdp_core_clk" - * "iface_clk" - * "bus_clk" - * "core_mmss_clk" - * "byte_clk" - * "pixel_clk" - * "core_clk" + * "mdp_core" + * "iface" + * "bus" + * "core_mmss" + * "byte" + * "pixel" + * "core" For DSIv2, we need an additional clock: - * "src_clk" -- assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform. + * "src" +- assigned-clocks: Parents of "byte" and "pixel" for the given platform. - assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided by a DSI PHY block. See [1] for details on clock bindings. - vdd-supply: phandle to vdd regulator device node @@ -101,7 +101,7 @@ Required properties: - power-domains: Should be <&mmcc MDSS_GDSC>. - clocks: Phandles to device clocks. See [1] for details on clock bindings. - clock-names: the following clocks are required: - * "iface_clk" + * "iface" - vddio-supply: phandle to vdd-io regulator device node Optional properties: @@ -123,13 +123,13 @@ Example: reg = <0xfd922800 0x200>; power-domains = <&mmcc MDSS_GDSC>; clock-names = - "bus_clk", - "byte_clk", - "core_clk", - "core_mmss_clk", - "iface_clk", - "mdp_core_clk", - "pixel_clk"; + "bus", + "byte", + "core", + "core_mmss", + "iface", + "mdp_core", + "pixel"; clocks = <&mmcc MDSS_AXI_CLK>, <&mmcc MDSS_BYTE0_CLK>, @@ -207,7 +207,7 @@ Example: reg = <0xfd922a00 0xd4>, <0xfd922b00 0x2b0>, <0xfd922d80 0x7b>; - clock-names = "iface_clk"; + clock-names = "iface"; clocks = <&mmcc MDSS_AHB_CLK>; #clock-cells = <1>; vddio-supply = <&pma8084_l12>; diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt index e63032be5401..95ce19ca7bc5 100644 --- a/Documentation/devicetree/bindings/display/msm/edp.txt +++ b/Documentation/devicetree/bindings/display/msm/edp.txt @@ -12,11 +12,11 @@ Required properties: - clocks: device clocks See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. - clock-names: the following clocks are required: - * "core_clk" - * "iface_clk" - * "mdp_core_clk" - * "pixel_clk" - * "link_clk" + * "core" + * "iface" + * "mdp_core" + * "pixel" + * "link" - #clock-cells: The value should be 1. - vdda-supply: phandle to vdda regulator device node - lvl-vdd-supply: phandle to regulator device node which is used to supply power @@ -41,11 +41,11 @@ Example: interrupts = <12 0>; power-domains = <&mmcc MDSS_GDSC>; clock-names = - "core_clk", - "pixel_clk", - "iface_clk", - "link_clk", - "mdp_core_clk"; + "core", + "pixel", + "iface", + "link", + "mdp_core"; clocks = <&mmcc MDSS_EDPAUX_CLK>, <&mmcc MDSS_EDPPIXEL_CLK>, diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt index 2d306f402d18..5f90a40da51b 100644 --- a/Documentation/devicetree/bindings/display/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -64,9 +64,9 @@ Example: interrupts = <GIC_SPI 79 0>; power-domains = <&mmcc MDSS_GDSC>; clock-names = - "core_clk", - "master_iface_clk", - "slave_iface_clk"; + "core", + "master_iface", + "slave_iface"; clocks = <&mmcc HDMI_APP_CLK>, <&mmcc HDMI_M_AHB_CLK>, @@ -92,7 +92,7 @@ Example: <0x4a00500 0x100>; #phy-cells = <0>; power-domains = <&mmcc MDSS_GDSC>; - clock-names = "slave_iface_clk"; + clock-names = "slave_iface"; clocks = <&mmcc HDMI_S_AHB_CLK>; core-vdda-supply = <&pm8921_hdmi_mvs>; }; diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt index 30c11ea83754..1b31977a68ba 100644 --- a/Documentation/devicetree/bindings/display/msm/mdp5.txt +++ b/Documentation/devicetree/bindings/display/msm/mdp5.txt @@ -22,16 +22,16 @@ Required properties: Documentation/devicetree/bindings/power/power_domain.txt - clocks: device clocks. See ../clocks/clock-bindings.txt for details. - clock-names: the following clocks are required. - * "iface_clk" - * "bus_clk" - * "vsync_clk" + * "iface" + * "bus" + * "vsync" - #address-cells: number of address cells for the MDSS children. Should be 1. - #size-cells: Should be 1. - ranges: parent bus address space is the same as the child bus address space. Optional properties: - clock-names: the following clocks are optional: - * "lut_clk" + * "lut" MDP5: Required properties: @@ -45,10 +45,10 @@ Required properties: through MDP block - clocks: device clocks. See ../clocks/clock-bindings.txt for details. - clock-names: the following clocks are required. -- * "bus_clk" -- * "iface_clk" -- * "core_clk" -- * "vsync_clk" +- * "bus" +- * "iface" +- * "core" +- * "vsync" - ports: contains the list of output ports from MDP. These connect to interfaces that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a special case since it is a part of the MDP block itself). @@ -77,7 +77,7 @@ Required properties: Optional properties: - clock-names: the following clocks are optional: - * "lut_clk" + * "lut" Example: @@ -95,9 +95,9 @@ Example: clocks = <&gcc GCC_MDSS_AHB_CLK>, <&gcc GCC_MDSS_AXI_CLK>, <&gcc GCC_MDSS_VSYNC_CLK>; - clock-names = "iface_clk", - "bus_clk", - "vsync_clk" + clock-names = "iface", + "bus", + "vsync" interrupts = <0 72 0>; @@ -120,10 +120,10 @@ Example: <&gcc GCC_MDSS_AXI_CLK>, <&gcc GCC_MDSS_MDP_CLK>, <&gcc GCC_MDSS_VSYNC_CLK>; - clock-names = "iface_clk", - "bus_clk", - "core_clk", - "vsync_clk"; + clock-names = "iface", + "bus", + "core", + "vsync"; ports { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt b/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt new file mode 100644 index 000000000000..6862028e7b2e --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt @@ -0,0 +1,21 @@ +Orise Tech OTM8009A 3.97" 480x800 TFT LCD panel (MIPI-DSI video mode) + +The Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD panel connected using +a MIPI-DSI video interface. Its backlight is managed through the DSI link. + +Required properties: + - compatible: "orisetech,otm8009a" + - reg: the virtual channel number of a DSI peripheral + +Optional properties: + - reset-gpios: a GPIO spec for the reset pin (active low). + +Example: +&dsi { + ... + panel@0 { + compatible = "orisetech,otm8009a"; + reg = <0>; + reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt new file mode 100644 index 000000000000..e9e19c059260 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/raspberrypi,7inch-touchscreen.txt @@ -0,0 +1,49 @@ +This binding covers the official 7" (800x480) Raspberry Pi touchscreen +panel. + +This DSI panel contains: + +- TC358762 DSI->DPI bridge +- Atmel microcontroller on I2C for power sequencing the DSI bridge and + controlling backlight +- Touchscreen controller on I2C for touch input + +and this binding covers the DSI display parts but not its touch input. + +Required properties: +- compatible: Must be "raspberrypi,7inch-touchscreen-panel" +- reg: Must be "45" +- port: See panel-common.txt + +Example: + +dsi1: dsi@7e700000 { + #address-cells = <1>; + #size-cells = <0>; + <...> + + port { + dsi_out_port: endpoint { + remote-endpoint = <&panel_dsi_port>; + }; + }; +}; + +i2c_dsi: i2c { + compatible = "i2c-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpio 28 0 + &gpio 29 0>; + + lcd@45 { + compatible = "raspberrypi,7inch-touchscreen-panel"; + reg = <0x45>; + + port { + panel_dsi_port: endpoint { + remote-endpoint = <&dsi_out_port>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt new file mode 100644 index 000000000000..3f1a8392af7f --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt @@ -0,0 +1,24 @@ +Samsung S6E63J0X03 1.63" 320x320 AMOLED panel (interface: MIPI-DSI command mode) + +Required properties: + - compatible: "samsung,s6e63j0x03" + - reg: the virtual channel number of a DSI peripheral + - vdd3-supply: I/O voltage supply + - vci-supply: voltage supply for analog circuits + - reset-gpios: a GPIO spec for the reset pin (active low) + - te-gpios: a GPIO spec for the tearing effect synchronization signal + gpio pin (active high) + +Example: +&dsi { + ... + + panel@0 { + compatible = "samsung,s6e63j0x03"; + reg = <0>; + vdd3-supply = <&ldo16_reg>; + vci-supply = <&ldo20_reg>; + reset-gpios = <&gpe0 1 GPIO_ACTIVE_LOW>; + te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt b/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt new file mode 100644 index 000000000000..aae57ef36cdd --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/seiko,43wvf1g.txt @@ -0,0 +1,23 @@ +Seiko Instruments Inc. 4.3" WVGA (800 x RGB x 480) TFT with Touch-Panel + +Required properties: +- compatible: should be "sii,43wvf1g". +- "dvdd-supply": 3v3 digital regulator. +- "avdd-supply": 5v analog regulator. + +Optional properties: +- backlight: phandle for the backlight control. + +Example: + + panel { + compatible = "sii,43wvf1g"; + backlight = <&backlight_display>; + dvdd-supply = <®_lcd_3v3>; + avdd-supply = <®_lcd_5v>; + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt new file mode 100644 index 000000000000..4c0caaf246c9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/toshiba,lt089ac29000.txt @@ -0,0 +1,8 @@ +Toshiba 8.9" WXGA (1280x768) TFT LCD panel + +Required properties: +- compatible: should be "toshiba,lt089ac29000.txt" +- power-supply: as specified in the base binding + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt new file mode 100644 index 000000000000..da6939efdb43 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/rockchip-lvds.txt @@ -0,0 +1,99 @@ +Rockchip RK3288 LVDS interface +================================ + +Required properties: +- compatible: matching the soc type, one of + - "rockchip,rk3288-lvds"; + +- reg: physical base address of the controller and length + of memory mapped region. +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. +- clock-names: must contain "pclk_lvds" + +- avdd1v0-supply: regulator phandle for 1.0V analog power +- avdd1v8-supply: regulator phandle for 1.8V analog power +- avdd3v3-supply: regulator phandle for 3.3V analog power + +- rockchip,grf: phandle to the general register files syscon +- rockchip,output: "rgb", "lvds" or "duallvds", This describes the output interface + +Optional properties: +- pinctrl-names: must contain a "lcdc" entry. +- pinctrl-0: pin control group to be used for this controller. + +Required nodes: + +The lvds has two video ports as described by + Documentation/devicetree/bindings/media/video-interfaces.txt +Their connections are modeled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt. + +- video port 0 for the VOP input, the remote endpoint maybe vopb or vopl +- video port 1 for either a panel or subsequent encoder + +the lvds panel described by + Documentation/devicetree/bindings/display/panel/simple-panel.txt + +Panel required properties: +- ports for remote LVDS output + +Panel optional properties: +- data-mapping: should be "vesa-24","jeida-24" or "jeida-18". +This describes decribed by: + Documentation/devicetree/bindings/display/panel/panel-lvds.txt + +Example: + +lvds_panel: lvds-panel { + compatible = "auo,b101ean01"; + enable-gpios = <&gpio7 21 GPIO_ACTIVE_HIGH>; + data-mapping = "jeida-24"; + + ports { + panel_in_lvds: endpoint { + remote-endpoint = <&lvds_out_panel>; + }; + }; +}; + +For Rockchip RK3288: + + lvds: lvds@ff96c000 { + compatible = "rockchip,rk3288-lvds"; + rockchip,grf = <&grf>; + reg = <0xff96c000 0x4000>; + clocks = <&cru PCLK_LVDS_PHY>; + clock-names = "pclk_lvds"; + pinctrl-names = "lcdc"; + pinctrl-0 = <&lcdc_ctl>; + avdd1v0-supply = <&vdd10_lcd>; + avdd1v8-supply = <&vcc18_lcd>; + avdd3v3-supply = <&vcca_33>; + rockchip,output = "rgb"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + lvds_in: port@0 { + reg = <0>; + + lvds_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_lvds>; + }; + lvds_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_lvds>; + }; + }; + + lvds_out: port@1 { + reg = <1>; + + lvds_out_panel: endpoint { + remote-endpoint = <&panel_in_lvds>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index b7faa6f6a326..50cc72ee1168 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -40,15 +40,19 @@ CEC. It is one end of the pipeline. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-hdmi * allwinner,sun5i-a10s-hdmi + * allwinner,sun6i-a31-hdmi - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the HDMI encoder * ahb: the HDMI interface clock * mod: the HDMI module clock + * ddc: the HDMI ddc clock (A31 only) * pll-0: the first video PLL * pll-1: the second video PLL - clock-names: the clock names mentioned above + - resets: phandle to the reset control for the HDMI encoder (A31 only) - dmas: phandles to the DMA channels used by the HDMI encoder * ddc-tx: The channel for DDC transmission * ddc-rx: The channel for DDC reception @@ -83,9 +87,11 @@ The TCON acts as a timing controller for RGB, LVDS and TV interfaces. Required properties: - compatible: value must be either: + * allwinner,sun4i-a10-tcon * allwinner,sun5i-a13-tcon * allwinner,sun6i-a31-tcon * allwinner,sun6i-a31s-tcon + * allwinner,sun7i-a20-tcon * allwinner,sun8i-a33-tcon * allwinner,sun8i-v3s-tcon - reg: base address and size of memory-mapped region @@ -150,8 +156,10 @@ system. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-display-backend * allwinner,sun5i-a13-display-backend * allwinner,sun6i-a31-display-backend + * allwinner,sun7i-a20-display-backend * allwinner,sun8i-a33-display-backend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -182,8 +190,10 @@ deinterlacing and color space conversion. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-display-frontend * allwinner,sun5i-a13-display-frontend * allwinner,sun6i-a31-display-frontend + * allwinner,sun7i-a20-display-frontend * allwinner,sun8i-a33-display-frontend - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP @@ -228,10 +238,12 @@ extra node. Required properties: - compatible: value must be one of: + * allwinner,sun4i-a10-display-engine * allwinner,sun5i-a10s-display-engine * allwinner,sun5i-a13-display-engine * allwinner,sun6i-a31-display-engine * allwinner,sun6i-a31s-display-engine + * allwinner,sun7i-a20-display-engine * allwinner,sun8i-a33-display-engine * allwinner,sun8i-v3s-display-engine diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index 74e1e8add5a1..844e0103fb0d 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -3,6 +3,10 @@ NVIDIA Tegra host1x Required properties: - compatible: "nvidia,tegra<chip>-host1x" - reg: Physical base address and length of the controller's registers. + For pre-Tegra186, one entry describing the whole register area. + For Tegra186, one entry for each entry in reg-names: + "vm" - VM region assigned to Linux + "hypervisor" - Hypervisor region (only if Linux acts as hypervisor) - interrupts: The interrupt outputs from the controller. - #address-cells: The number of cells used to represent physical base addresses in the host1x address space. Should be 1. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 0f295a4798ad..1db9dbef3e56 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -254,6 +254,7 @@ opencores OpenCores.org openrisc OpenRISC.io option Option NV ORCL Oracle Corporation +orisetech Orise Technology ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies oxsemi Oxford Semiconductor, Ltd. diff --git a/Documentation/gpu/drm-uapi.rst b/Documentation/gpu/drm-uapi.rst index 679373b4a03f..a2214cc1f821 100644 --- a/Documentation/gpu/drm-uapi.rst +++ b/Documentation/gpu/drm-uapi.rst @@ -168,6 +168,61 @@ IOCTL Support on Device Nodes .. kernel-doc:: drivers/gpu/drm/drm_ioctl.c :doc: driver specific ioctls +Recommended IOCTL Return Values +------------------------------- + +In theory a driver's IOCTL callback is only allowed to return very few error +codes. In practice it's good to abuse a few more. This section documents common +practice within the DRM subsystem: + +ENOENT: + Strictly this should only be used when a file doesn't exist e.g. when + calling the open() syscall. We reuse that to signal any kind of object + lookup failure, e.g. for unknown GEM buffer object handles, unknown KMS + object handles and similar cases. + +ENOSPC: + Some drivers use this to differentiate "out of kernel memory" from "out + of VRAM". Sometimes also applies to other limited gpu resources used for + rendering (e.g. when you have a special limited compression buffer). + Sometimes resource allocation/reservation issues in command submission + IOCTLs are also signalled through EDEADLK. + + Simply running out of kernel/system memory is signalled through ENOMEM. + +EPERM/EACCESS: + Returned for an operation that is valid, but needs more privileges. + E.g. root-only or much more common, DRM master-only operations return + this when when called by unpriviledged clients. There's no clear + difference between EACCESS and EPERM. + +ENODEV: + Feature (like PRIME, modesetting, GEM) is not supported by the driver. + +ENXIO: + Remote failure, either a hardware transaction (like i2c), but also used + when the exporting driver of a shared dma-buf or fence doesn't support a + feature needed. + +EINTR: + DRM drivers assume that userspace restarts all IOCTLs. Any DRM IOCTL can + return EINTR and in such a case should be restarted with the IOCTL + parameters left unchanged. + +EIO: + The GPU died and couldn't be resurrected through a reset. Modesetting + hardware failures are signalled through the "link status" connector + property. + +EINVAL: + Catch-all for anything that is an invalid argument combination which + cannot work. + +IOCTL also use other error codes like ETIME, EFAULT, EBUSY, ENOTTY but their +usage is in line with the common meanings. The above list tries to just document +DRM specific patterns. Note that ENOTTY has the slightly unintuitive meaning of +"this IOCTL does not exist", and is used exactly as such in DRM. + .. kernel-doc:: include/drm/drm_ioctl.h :internal: diff --git a/Documentation/gpu/index.rst b/Documentation/gpu/index.rst index 35d673bf9b56..c36586dad29d 100644 --- a/Documentation/gpu/index.rst +++ b/Documentation/gpu/index.rst @@ -15,6 +15,7 @@ Linux GPU Driver Developer's Guide pl111 tegra tinydrm + tve200 vc4 vga-switcheroo vgaarbiter diff --git a/Documentation/gpu/todo.rst b/Documentation/gpu/todo.rst index 22af55d06ab8..96f8ec7dbe4e 100644 --- a/Documentation/gpu/todo.rst +++ b/Documentation/gpu/todo.rst @@ -75,17 +75,6 @@ helpers. Contact: Ville Syrjälä, Daniel Vetter, driver maintainers -Implement deferred fbdev setup in the helper --------------------------------------------- - -Many (especially embedded drivers) want to delay fbdev setup until there's a -real screen plugged in. This is to avoid the dreaded fallback to the low-res -fbdev default. Many drivers have a hacked-up (and often broken) version of this, -better to do it once in the shared helpers. Thierry has a patch series, but that -one needs to be rebased and final polish applied. - -Contact: Thierry Reding, Daniel Vetter, driver maintainers - Convert early atomic drivers to async commit helpers ---------------------------------------------------- @@ -138,6 +127,8 @@ interfaces to fix these issues: the acquire context explicitly on stack and then also pass it down into drivers explicitly so that the legacy-on-atomic functions can use them. + Except for some driver code this is done. + * A bunch of the vtable hooks are now in the wrong place: DRM has a split between core vfunc tables (named ``drm_foo_funcs``), which are used to implement the userspace ABI. And then there's the optional hooks for the @@ -151,6 +142,8 @@ interfaces to fix these issues: connector at runtime. That's almost all of them, and would allow us to get rid of a lot of ``best_encoder`` boilerplate in drivers. + This was almost done, but new drivers added a few more cases again. + Contact: Daniel Vetter Get rid of dev->struct_mutex from GEM drivers @@ -177,14 +170,19 @@ following drivers still use ``struct_mutex``: ``msm``, ``omapdrm`` and Contact: Daniel Vetter, respective driver maintainers -Core refactorings -================= +Convert instances of dev_info/dev_err/dev_warn to their DRM_DEV_* equivalent +---------------------------------------------------------------------------- -Use new IDR deletion interface to clean up drm_gem_handle_delete() ------------------------------------------------------------------- +For drivers which could have multiple instances, it is necessary to +differentiate between which is which in the logs. Since DRM_INFO/WARN/ERROR +don't do this, drivers used dev_info/warn/err to make this differentiation. We +now have DRM_DEV_* variants of the drm print macros, so we can start to convert +those drivers back to using drm-formwatted specific log messages. -See the "This is gross" comment -- apparently the IDR system now can return an -error code instead of oopsing. +Contact: Sean Paul, Maintainer of the driver you plan to convert + +Core refactorings +================= Clean up the DRM header mess ---------------------------- @@ -306,6 +304,18 @@ There's a bunch of issues with it: Contact: Daniel Vetter +KMS cleanups +------------ + +Some of these date from the very introduction of KMS in 2008 ... + +- drm_mode_config.crtc_idr is misnamed, since it contains all KMS object. Should + be renamed to drm_mode_config.object_idr. + +- drm_display_mode doesn't need to be derived from drm_mode_object. That's + leftovers from older (never merged into upstream) KMS designs where modes + where set using their ID, including support to add/remove modes. + Better Testing ============== @@ -353,7 +363,16 @@ those drivers as simple as possible, so lots of room for refactoring: - backlight helpers, probably best to put them into a new drm_backlight.c. This is because drivers/video is de-facto unmaintained. We could also move drivers/video/backlight to drivers/gpu/backlight and take it all - over within drm-misc, but that's more work. + over within drm-misc, but that's more work. Backlight helpers require a fair + bit of reworking and refactoring. A simple example is the enabling of a backlight. + Tinydrm has helpers for this. It would be good if other drivers can also use the + helper. However, there are various cases we need to consider i.e different + drivers seem to have different ways of enabling/disabling a backlight. + We also need to consider the backlight drivers (like gpio_backlight). The situation + is further complicated by the fact that the backlight is tied to fbdev + via fb_notifier_callback() which has complicated logic. For further details, refer + to the following discussion thread: + https://groups.google.com/forum/#!topic/outreachy-kernel/8rBe30lwtdA - spi helpers, probably best put into spi core/helper code. Thierry said the spi maintainer is fast&reactive, so shouldn't be a big issue. diff --git a/Documentation/gpu/tve200.rst b/Documentation/gpu/tve200.rst new file mode 100644 index 000000000000..69b17b324e12 --- /dev/null +++ b/Documentation/gpu/tve200.rst @@ -0,0 +1,6 @@ +================================== + drm/tve200 Faraday TV Encoder 200 +================================== + +.. kernel-doc:: drivers/gpu/drm/tve200/tve200_drv.c + :doc: Faraday TV Encoder 200 |