diff options
Diffstat (limited to 'Documentation/devicetree')
7 files changed, 359 insertions, 149 deletions
diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml index 0f6374ceaa69..9af873b43acd 100644 --- a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml +++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-csi.yaml @@ -16,7 +16,15 @@ description: |- properties: compatible: - const: allwinner,sun7i-a20-csi0 + oneOf: + - const: allwinner,sun4i-a10-csi1 + - const: allwinner,sun7i-a20-csi0 + - items: + - const: allwinner,sun7i-a20-csi1 + - const: allwinner,sun4i-a10-csi1 + - items: + - const: allwinner,sun8i-r40-csi0 + - const: allwinner,sun7i-a20-csi0 reg: maxItems: 1 @@ -25,12 +33,16 @@ properties: maxItems: 1 clocks: + minItems: 2 + maxItems: 3 items: - description: The CSI interface clock - description: The CSI ISP clock - description: The CSI DRAM clock clock-names: + minItems: 2 + maxItems: 3 items: - const: bus - const: isp diff --git a/Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml b/Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml new file mode 100644 index 000000000000..335717e15970 --- /dev/null +++ b/Documentation/devicetree/bindings/media/amlogic,gx-vdec.yaml @@ -0,0 +1,141 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/media/amlogic,gx-vdec.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Video Decoder + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + - Maxime Jourdan <mjourdan@baylibre.com> + +description: | + The video decoding IP lies within the DOS memory region, + except for the hardware bitstream parser that makes use of an undocumented + region. + + It makes use of the following blocks: + - ESPARSER is a bitstream parser that outputs to a VIFIFO. Further VDEC blocks + then feed from this VIFIFO. + - VDEC_1 can decode MPEG-1, MPEG-2, MPEG-4 part 2, MJPEG, H.263, H.264, VC-1. + - VDEC_HEVC can decode HEVC and VP9. + + Both VDEC_1 and VDEC_HEVC share the "vdec" IRQ and as such cannot run + concurrently. + +properties: + compatible: + oneOf: + - items: + - enum: + - amlogic,gxbb-vdec # GXBB (S905) + - amlogic,gxl-vdec # GXL (S905X, S905D) + - amlogic,gxm-vdec # GXM (S912) + - const: amlogic,gx-vdec + - enum: + - amlogic,g12a-vdec # G12A (S905X2, S905D2) + - amlogic,sm1-vdec # SM1 (S905X3, S905D3) + + interrupts: + minItems: 2 + + interrupt-names: + items: + - const: vdec + - const: esparser + + reg: + minItems: 2 + + reg-names: + items: + - const: dos + - const: esparser + + resets: + maxItems: 1 + + reset-names: + items: + - const: esparser + + clocks: + minItems: 4 + maxItems: 5 + + clock-names: + minItems: 4 + maxItems: 5 + items: + - const: dos_parser + - const: dos + - const: vdec_1 + - const: vdec_hevc + - const: vdec_hevcf + + amlogic,ao-sysctrl: + description: should point to the AOBUS sysctrl node + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle + + amlogic,canvas: + description: should point to a canvas provider node + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle + +allOf: + - if: + properties: + compatible: + contains: + enum: + - amlogic,gx-vdec + + then: + properties: + clock-names: + maxItems: 4 + + - if: + properties: + compatible: + contains: + enum: + - amlogic,g12a-vdec + - amlogic,sm1-vdec + + then: + properties: + clock-names: + minItems: 5 + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-names + - clocks + - clock-names + - resets + - reset-names + - amlogic,ao-sysctrl + - amlogic,canvas + +examples: + - | + vdec: video-decoder@c8820000 { + compatible = "amlogic,gxl-vdec", "amlogic,gx-vdec"; + reg = <0xc8820000 0x10000>, <0xc110a580 0xe4>; + reg-names = "dos", "esparser"; + interrupts = <44>, <32>; + interrupt-names = "vdec", "esparser"; + clocks = <&clk_dos_parser> ,<&clk_dos>, <&clk_vdec_1>, <&clk_vdec_hevc>; + clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc"; + resets = <&reset_parser>; + reset-names = "esparser"; + amlogic,ao-sysctrl = <&sysctrl_AO>; + amlogic,canvas = <&canvas>; + }; diff --git a/Documentation/devicetree/bindings/media/amlogic,vdec.txt b/Documentation/devicetree/bindings/media/amlogic,vdec.txt deleted file mode 100644 index 9b6aace86ca7..000000000000 --- a/Documentation/devicetree/bindings/media/amlogic,vdec.txt +++ /dev/null @@ -1,72 +0,0 @@ -Amlogic Video Decoder -================================ - -The video decoding IP lies within the DOS memory region, -except for the hardware bitstream parser that makes use of an undocumented -region. - -It makes use of the following blocks: - -- ESPARSER is a bitstream parser that outputs to a VIFIFO. Further VDEC blocks -then feed from this VIFIFO. -- VDEC_1 can decode MPEG-1, MPEG-2, MPEG-4 part 2, MJPEG, H.263, H.264, VC-1. -- VDEC_HEVC can decode HEVC and VP9. - -Both VDEC_1 and VDEC_HEVC share the "vdec" IRQ and as such cannot run -concurrently. - -Device Tree Bindings: ---------------------- - -VDEC: Video Decoder --------------------------- - -Required properties: -- compatible: value should be different for each SoC family as : - - GXBB (S905) : "amlogic,gxbb-vdec" - - GXL (S905X, S905D) : "amlogic,gxl-vdec" - - GXM (S912) : "amlogic,gxm-vdec" - followed by the common "amlogic,gx-vdec" -- reg: base address and size of he following memory-mapped regions : - - dos - - esparser -- reg-names: should contain the names of the previous memory regions -- interrupts: should contain the following IRQs: - - vdec - - esparser -- interrupt-names: should contain the names of the previous interrupts -- amlogic,ao-sysctrl: should point to the AOBUS sysctrl node -- amlogic,canvas: should point to a canvas provider node -- clocks: should contain the following clocks : - - dos_parser - - dos - - vdec_1 - - vdec_hevc -- clock-names: should contain the names of the previous clocks -- resets: should contain the parser reset -- reset-names: should be "esparser" - -Example: - -vdec: video-codec@c8820000 { - compatible = "amlogic,gxbb-vdec", "amlogic,gx-vdec"; - reg = <0x0 0xc8820000 0x0 0x10000>, - <0x0 0xc110a580 0x0 0xe4>; - reg-names = "dos", "esparser"; - - interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>, - <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>; - interrupt-names = "vdec", "esparser"; - - amlogic,ao-sysctrl = <&sysctrl_AO>; - amlogic,canvas = <&canvas>; - - clocks = <&clkc CLKID_DOS_PARSER>, - <&clkc CLKID_DOS>, - <&clkc CLKID_VDEC_1>, - <&clkc CLKID_VDEC_HEVC>; - clock-names = "dos_parser", "dos", "vdec_1", "vdec_hevc"; - - resets = <&reset RESET_PARSER>; - reset-names = "esparser"; -}; diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt index 13ebc0fac9ea..ca4cf774662e 100644 --- a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -1,7 +1,8 @@ Device-Tree bindings for hix5hd2 ir IP Required properties: - - compatible: Should contain "hisilicon,hix5hd2-ir". + - compatible: Should contain "hisilicon,hix5hd2-ir", or: + - "hisilicon,hi3796cv300-ir" for Hi3796CV300 IR device. - reg: Base physical address of the controller and length of memory mapped region. - interrupts: interrupt-specifier for the sole interrupt generated by diff --git a/Documentation/devicetree/bindings/media/renesas,vin.txt b/Documentation/devicetree/bindings/media/renesas,vin.txt index e30b0d4eefdd..5eefd62ac5c5 100644 --- a/Documentation/devicetree/bindings/media/renesas,vin.txt +++ b/Documentation/devicetree/bindings/media/renesas,vin.txt @@ -13,6 +13,7 @@ on Gen3 and RZ/G2 platforms to a CSI-2 receiver. - "renesas,vin-r8a7743" for the R8A7743 device - "renesas,vin-r8a7744" for the R8A7744 device - "renesas,vin-r8a7745" for the R8A7745 device + - "renesas,vin-r8a77470" for the R8A77470 device - "renesas,vin-r8a774a1" for the R8A774A1 device - "renesas,vin-r8a774b1" for the R8A774B1 device - "renesas,vin-r8a774c0" for the R8A774C0 device @@ -41,9 +42,6 @@ on Gen3 and RZ/G2 platforms to a CSI-2 receiver. - interrupts: the interrupt for the device - clocks: Reference to the parent clock -Additionally, an alias named vinX will need to be created to specify -which video input device this is. - The per-board settings for Gen2 and RZ/G1 platforms: - port - sub-node describing a single endpoint connected to the VIN diff --git a/Documentation/devicetree/bindings/media/ti,cal.yaml b/Documentation/devicetree/bindings/media/ti,cal.yaml new file mode 100644 index 000000000000..1ea784179536 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,cal.yaml @@ -0,0 +1,202 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/ti,cal.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) Device Tree Bindings + +maintainers: + - Benoit Parrot <bparrot@ti.com> + +description: |- + The Camera Adaptation Layer (CAL) is a key component for image capture + applications. The capture module provides the system interface and the + processing capability to connect CSI2 image-sensor modules to the + DRA72x device. + + CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes + should contain a 'port' child node with child 'endpoint' node. Please + refer to the bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + +properties: + compatible: + enum: + # for DRA72 controllers + - ti,dra72-cal + # for DRA72 controllers pre ES2.0 + - ti,dra72-pre-es2-cal + # for DRA76 controllers + - ti,dra76-cal + # for AM654 controllers + - ti,am654-cal + + reg: + minItems: 2 + items: + - description: The CAL main register region + - description: The RX Core0 (DPHY0) register region + - description: The RX Core1 (DPHY1) register region + + reg-names: + minItems: 2 + items: + - const: cal_top + - const: cal_rx_core0 + - const: cal_rx_core1 + + interrupts: + maxItems: 1 + + ti,camerrx-control: + $ref: "/schemas/types.yaml#/definitions/phandle-array" + description: + phandle to the device control module and offset to the + control_camerarx_core register + + clocks: + maxItems: 1 + + clock-names: + const: fck + + power-domains: + description: + List of phandle and PM domain specifier as documented in + Documentation/devicetree/bindings/power/power_domain.txt + maxItems: 1 + + # See ./video-interfaces.txt for details + ports: + type: object + additionalProperties: false + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + port@0: + type: object + additionalProperties: false + + properties: + reg: + const: 0 + description: CSI2 Port #0 + + patternProperties: + endpoint: + type: object + additionalProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + remote-endpoint: true + + required: + - reg + + port@1: + type: object + additionalProperties: false + + properties: + reg: + const: 1 + description: CSI2 Port #1 + + patternProperties: + endpoint: + type: object + additionalProperties: false + + properties: + clock-lanes: + maxItems: 1 + + data-lanes: + minItems: 1 + maxItems: 4 + + remote-endpoint: true + + required: + - reg + + required: + - "#address-cells" + - "#size-cells" + - port@0 + +required: + - compatible + - reg + - reg-names + - interrupts + - ti,camerrx-control + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + cal: cal@4845b000 { + compatible = "ti,dra72-cal"; + reg = <0x4845B000 0x400>, + <0x4845B800 0x40>, + <0x4845B900 0x40>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + ti,camerrx-control = <&scm_conf 0xE94>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + csi2_phy0: endpoint { + remote-endpoint = <&csi2_cam0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + + i2c5: i2c@4807c000 { + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + + camera-sensor@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + + clocks = <&clk_ov5640_fixed>; + clock-names = "xclk"; + + port { + csi2_cam0: endpoint { + remote-endpoint = <&csi2_phy0>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/media/ti-cal.txt b/Documentation/devicetree/bindings/media/ti-cal.txt deleted file mode 100644 index ae9b52f37576..000000000000 --- a/Documentation/devicetree/bindings/media/ti-cal.txt +++ /dev/null @@ -1,72 +0,0 @@ -Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) ------------------------------------------------------- - -The Camera Adaptation Layer (CAL) is a key component for image capture -applications. The capture module provides the system interface and the -processing capability to connect CSI2 image-sensor modules to the -DRA72x device. - -Required properties: -- compatible: must be "ti,dra72-cal" -- reg: CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX - control address space -- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control - registers -- interrupts: should contain IRQ line for the CAL; - -CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes -should contain a 'port' child node with child 'endpoint' node. Please -refer to the bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. - -Example: - cal: cal@4845b000 { - compatible = "ti,dra72-cal"; - ti,hwmods = "cal"; - reg = <0x4845B000 0x400>, - <0x4845B800 0x40>, - <0x4845B900 0x40>, - <0x4A002e94 0x4>; - reg-names = "cal_top", - "cal_rx_core0", - "cal_rx_core1", - "camerrx_control"; - interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - csi2_0: port@0 { - reg = <0>; - endpoint { - slave-mode; - remote-endpoint = <&ar0330_1>; - }; - }; - csi2_1: port@1 { - reg = <1>; - }; - }; - }; - - i2c5: i2c@4807c000 { - ar0330@10 { - compatible = "ti,ar0330"; - reg = <0x10>; - - port { - #address-cells = <1>; - #size-cells = <0>; - - ar0330_1: endpoint { - reg = <0>; - clock-lanes = <1>; - data-lanes = <0 2 3 4>; - remote-endpoint = <&csi2_0>; - }; - }; - }; - }; |