diff options
| -rw-r--r-- | arch/blackfin/include/asm/bfin_sdh.h | 119 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf518/include/mach/defBF514.h | 135 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/defBF542.h | 130 | ||||
| -rw-r--r-- | arch/blackfin/mach-bf548/include/mach/defBF547.h | 130 |
4 files changed, 117 insertions, 397 deletions
diff --git a/arch/blackfin/include/asm/bfin_sdh.h b/arch/blackfin/include/asm/bfin_sdh.h index d61d5497c590..6a4cfe2d3367 100644 --- a/arch/blackfin/include/asm/bfin_sdh.h +++ b/arch/blackfin/include/asm/bfin_sdh.h @@ -1,7 +1,7 @@ /* - * bfin_sdh.h - Blackfin SDH definitions + * Blackfin Secure Digital Host (SDH) definitions * - * Copyright 2008 Analog Devices Inc. + * Copyright 2008-2010 Analog Devices Inc. * * Licensed under the GPL-2 or later. */ @@ -9,6 +9,7 @@ #ifndef __BFIN_SDH_H__ #define __BFIN_SDH_H__ +/* Platform resources */ struct bfin_sd_host { int dma_chan; int irq_int0; @@ -16,4 +17,118 @@ struct bfin_sd_host { u16 pin_req[7]; }; +/* SDH_COMMAND bitmasks */ +#define CMD_IDX 0x3f /* Command Index */ +#define CMD_RSP (1 << 6) /* Response */ +#define CMD_L_RSP (1 << 7) /* Long Response */ +#define CMD_INT_E (1 << 8) /* Command Interrupt */ +#define CMD_PEND_E (1 << 9) /* Command Pending */ +#define CMD_E (1 << 10) /* Command Enable */ + +/* SDH_PWR_CTL bitmasks */ +#define PWR_ON 0x3 /* Power On */ +#define SD_CMD_OD (1 << 6) /* Open Drain Output */ +#define ROD_CTL (1 << 7) /* Rod Control */ + +/* SDH_CLK_CTL bitmasks */ +#define CLKDIV 0xff /* MC_CLK Divisor */ +#define CLK_E (1 << 8) /* MC_CLK Bus Clock Enable */ +#define PWR_SV_E (1 << 9) /* Power Save Enable */ +#define CLKDIV_BYPASS (1 << 10) /* Bypass Divisor */ +#define WIDE_BUS (1 << 11) /* Wide Bus Mode Enable */ + +/* SDH_RESP_CMD bitmasks */ +#define RESP_CMD 0x3f /* Response Command */ + +/* SDH_DATA_CTL bitmasks */ +#define DTX_E (1 << 0) /* Data Transfer Enable */ +#define DTX_DIR (1 << 1) /* Data Transfer Direction */ +#define DTX_MODE (1 << 2) /* Data Transfer Mode */ +#define DTX_DMA_E (1 << 3) /* Data Transfer DMA Enable */ +#define DTX_BLK_LGTH (0xf << 4) /* Data Transfer Block Length */ + +/* SDH_STATUS bitmasks */ +#define CMD_CRC_FAIL (1 << 0) /* CMD CRC Fail */ +#define DAT_CRC_FAIL (1 << 1) /* Data CRC Fail */ +#define CMD_TIME_OUT (1 << 2) /* CMD Time Out */ +#define DAT_TIME_OUT (1 << 3) /* Data Time Out */ +#define TX_UNDERRUN (1 << 4) /* Transmit Underrun */ +#define RX_OVERRUN (1 << 5) /* Receive Overrun */ +#define CMD_RESP_END (1 << 6) /* CMD Response End */ +#define CMD_SENT (1 << 7) /* CMD Sent */ +#define DAT_END (1 << 8) /* Data End */ +#define START_BIT_ERR (1 << 9) /* Start Bit Error */ +#define DAT_BLK_END (1 << 10) /* Data Block End */ +#define CMD_ACT (1 << 11) /* CMD Active */ +#define TX_ACT (1 << 12) /* Transmit Active */ +#define RX_ACT (1 << 13) /* Receive Active */ +#define TX_FIFO_STAT (1 << 14) /* Transmit FIFO Status */ +#define RX_FIFO_STAT (1 << 15) /* Receive FIFO Status */ +#define TX_FIFO_FULL (1 << 16) /* Transmit FIFO Full */ +#define RX_FIFO_FULL (1 << 17) /* Receive FIFO Full */ +#define TX_FIFO_ZERO (1 << 18) /* Transmit FIFO Empty */ +#define RX_DAT_ZERO (1 << 19) /* Receive FIFO Empty */ +#define TX_DAT_RDY (1 << 20) /* Transmit Data Available */ +#define RX_FIFO_RDY (1 << 21) /* Receive Data Available */ + +/* SDH_STATUS_CLR bitmasks */ +#define CMD_CRC_FAIL_STAT (1 << 0) /* CMD CRC Fail Status */ +#define DAT_CRC_FAIL_STAT (1 << 1) /* Data CRC Fail Status */ +#define CMD_TIMEOUT_STAT (1 << 2) /* CMD Time Out Status */ +#define DAT_TIMEOUT_STAT (1 << 3) /* Data Time Out status */ +#define TX_UNDERRUN_STAT (1 << 4) /* Transmit Underrun Status */ +#define RX_OVERRUN_STAT (1 << 5) /* Receive Overrun Status */ +#define CMD_RESP_END_STAT (1 << 6) /* CMD Response End Status */ +#define CMD_SENT_STAT (1 << 7) /* CMD Sent Status */ +#define DAT_END_STAT (1 << 8) /* Data End Status */ +#define START_BIT_ERR_STAT (1 << 9) /* Start Bit Error Status */ +#define DAT_BLK_END_STAT (1 << 10) /* Data Block End Status */ + +/* SDH_MASK0 bitmasks */ +#define CMD_CRC_FAIL_MASK (1 << 0) /* CMD CRC Fail Mask */ +#define DAT_CRC_FAIL_MASK (1 << 1) /* Data CRC Fail Mask */ +#define CMD_TIMEOUT_MASK (1 << 2) /* CMD Time Out Mask */ +#define DAT_TIMEOUT_MASK (1 << 3) /* Data Time Out Mask */ +#define TX_UNDERRUN_MASK (1 << 4) /* Transmit Underrun Mask */ +#define RX_OVERRUN_MASK (1 << 5) /* Receive Overrun Mask */ +#define CMD_RESP_END_MASK (1 << 6) /* CMD Response End Mask */ +#define CMD_SENT_MASK (1 << 7) /* CMD Sent Mask */ +#define DAT_END_MASK (1 << 8) /* Data End Mask */ +#define START_BIT_ERR_MASK (1 << 9) /* Start Bit Error Mask */ +#define DAT_BLK_END_MASK (1 << 10) /* Data Block End Mask */ +#define CMD_ACT_MASK (1 << 11) /* CMD Active Mask */ +#define TX_ACT_MASK (1 << 12) /* Transmit Active Mask */ +#define RX_ACT_MASK (1 << 13) /* Receive Active Mask */ +#define TX_FIFO_STAT_MASK (1 << 14) /* Transmit FIFO Status Mask */ +#define RX_FIFO_STAT_MASK (1 << 15) /* Receive FIFO Status Mask */ +#define TX_FIFO_FULL_MASK (1 << 16) /* Transmit FIFO Full Mask */ +#define RX_FIFO_FULL_MASK (1 << 17) /* Receive FIFO Full Mask */ +#define TX_FIFO_ZERO_MASK (1 << 18) /* Transmit FIFO Empty Mask */ +#define RX_DAT_ZERO_MASK (1 << 19) /* Receive FIFO Empty Mask */ +#define TX_DAT_RDY_MASK (1 << 20) /* Transmit Data Available Mask */ +#define RX_FIFO_RDY_MASK (1 << 21) /* Receive Data Available Mask */ + +/* SDH_FIFO_CNT bitmasks */ +#define FIFO_COUNT 0x7fff /* FIFO Count */ + +/* SDH_E_STATUS bitmasks */ +#define SDIO_INT_DET (1 << 1) /* SDIO Int Detected */ +#define SD_CARD_DET (1 << 4) /* SD Card Detect */ + +/* SDH_E_MASK bitmasks */ +#define SDIO_MSK (1 << 1) /* Mask SDIO Int Detected */ +#define SCD_MSK (1 << 6) /* Mask Card Detect */ + +/* SDH_CFG bitmasks */ +#define CLKS_EN (1 << 0) /* Clocks Enable */ +#define SD4E (1 << 2) /* SDIO 4-Bit Enable */ +#define MWE (1 << 3) /* Moving Window Enable */ +#define SD_RST (1 << 4) /* SDMMC Reset */ +#define PUP_SDDAT (1 << 5) /* Pull-up SD_DAT */ +#define PUP_SDDAT3 (1 << 6) /* Pull-up SD_DAT3 */ +#define PD_SDDAT3 (1 << 7) /* Pull-down SD_DAT3 */ + +/* SDH_RD_WAIT_EN bitmasks */ +#define RWR (1 << 0) /* Read Wait Request */ + #endif diff --git a/arch/blackfin/mach-bf518/include/mach/defBF514.h b/arch/blackfin/mach-bf518/include/mach/defBF514.h index 92e950d6e996..98a51c479290 100644 --- a/arch/blackfin/mach-bf518/include/mach/defBF514.h +++ b/arch/blackfin/mach-bf518/include/mach/defBF514.h @@ -45,139 +45,4 @@ #define RSI_PID6 0xFFC03FF8 /* RSI Peripheral ID Register 6 */ #define RSI_PID7 0xFFC03FFC /* RSI Peripheral ID Register 7 */ -/* ********************************************************** */ -/* SINGLE BIT MACRO PAIRS (bit mask and negated one) */ -/* and MULTI BIT READ MACROS */ -/* ********************************************************** */ - -/* Bit masks for SDH_COMMAND */ - -#define CMD_IDX 0x3f /* Command Index */ -#define CMD_RSP 0x40 /* Response */ -#define CMD_L_RSP 0x80 /* Long Response */ -#define CMD_INT_E 0x100 /* Command Interrupt */ -#define CMD_PEND_E 0x200 /* Command Pending */ -#define CMD_E 0x400 /* Command Enable */ - -/* Bit masks for SDH_PWR_CTL */ - -#define PWR_ON 0x3 /* Power On */ -#if 0 -#define TBD 0x3c /* TBD */ -#endif -#define SD_CMD_OD 0x40 /* Open Drain Output */ -#define ROD_CTL 0x80 /* Rod Control */ - -/* Bit masks for SDH_CLK_CTL */ - -#define CLKDIV 0xff /* MC_CLK Divisor */ -#define CLK_E 0x100 /* MC_CLK Bus Clock Enable */ -#define PWR_SV_E 0x200 /* Power Save Enable */ -#define CLKDIV_BYPASS 0x400 /* Bypass Divisor */ -#define WIDE_BUS 0x800 /* Wide Bus Mode Enable */ - -/* Bit masks for SDH_RESP_CMD */ - -#define RESP_CMD 0x3f /* Response Command */ - -/* Bit masks for SDH_DATA_CTL */ - -#define DTX_E 0x1 /* Data Transfer Enable */ -#define DTX_DIR 0x2 /* Data Transfer Direction */ -#define DTX_MODE 0x4 /* Data Transfer Mode */ -#define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */ -#define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */ - -/* Bit masks for SDH_STATUS */ - -#define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */ -#define DAT_CRC_FAIL 0x2 /* Data CRC Fail */ -#define CMD_TIME_OUT 0x4 /* CMD Time Out */ -#define DAT_TIME_OUT 0x8 /* Data Time Out */ -#define TX_UNDERRUN 0x10 /* Transmit Underrun */ -#define RX_OVERRUN 0x20 /* Receive Overrun */ -#define CMD_RESP_END 0x40 /* CMD Response End */ -#define CMD_SENT 0x80 /* CMD Sent */ -#define DAT_END 0x100 /* Data End */ -#define START_BIT_ERR 0x200 /* Start Bit Error */ -#define DAT_BLK_END 0x400 /* Data Block End */ -#define CMD_ACT 0x800 /* CMD Active */ -#define TX_ACT 0x1000 /* Transmit Active */ -#define RX_ACT 0x2000 /* Receive Active */ -#define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */ -#define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */ -#define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */ -#define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */ -#define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */ -#define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */ -#define TX_DAT_RDY 0x100000 /* Transmit Data Available */ -#define RX_FIFO_RDY 0x200000 /* Receive Data Available */ - -/* Bit masks for SDH_STATUS_CLR */ - -#define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */ -#define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */ -#define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */ -#define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */ -#define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */ -#define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */ -#define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */ -#define CMD_SENT_STAT 0x80 /* CMD Sent Status */ -#define DAT_END_STAT 0x100 /* Data End Status */ -#define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */ -#define DAT_BLK_END_STAT 0x400 /* Data Block End Status */ - -/* Bit masks for SDH_MASK0 */ - -#define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */ -#define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */ -#define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */ -#define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */ -#define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */ -#define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */ -#define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */ -#define CMD_SENT_MASK 0x80 /* CMD Sent Mask */ -#define DAT_END_MASK 0x100 /* Data End Mask */ -#define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */ -#define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */ -#define CMD_ACT_MASK 0x800 /* CMD Active Mask */ -#define TX_ACT_MASK 0x1000 /* Transmit Active Mask */ -#define RX_ACT_MASK 0x2000 /* Receive Active Mask */ -#define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */ -#define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */ -#define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */ -#define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */ -#define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */ -#define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */ -#define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */ -#define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */ - -/* Bit masks for SDH_FIFO_CNT */ - -#define FIFO_COUNT 0x7fff /* FIFO Count */ - -/* Bit masks for SDH_E_STATUS */ - -#define SDIO_INT_DET 0x2 /* SDIO Int Detected */ -#define SD_CARD_DET 0x10 /* SD Card Detect */ - -/* Bit masks for SDH_E_MASK */ - -#define SDIO_MSK 0x2 /* Mask SDIO Int Detected */ -#define SCD_MSK 0x40 /* Mask Card Detect */ - -/* Bit masks for SDH_CFG */ - -#define CLKS_EN 0x1 /* Clocks Enable */ -#define SD4E 0x4 /* SDIO 4-Bit Enable */ -#define MWE 0x8 /* Moving Window Enable */ -#define SD_RST 0x10 /* SDMMC Reset */ -#define PUP_SDDAT 0x20 /* Pull-up SD_DAT */ -#define PUP_SDDAT3 0x40 /* Pull-up SD_DAT3 */ -#define PD_SDDAT3 0x80 /* Pull-down SD_DAT3 */ - -/* Bit masks for SDH_RD_WAIT_EN */ - -#define RWR 0x1 /* Read Wait Request */ - #endif /* _DEF_BF514_H */ diff --git a/arch/blackfin/mach-bf548/include/mach/defBF542.h b/arch/blackfin/mach-bf548/include/mach/defBF542.h index d3bc6d1df547..abf5f750dd8b 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF542.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF542.h @@ -366,136 +366,6 @@ #define KPAD_SOFTEVAL_E 0x2 /* Software Programmable Force Evaluate */ -/* Bit masks for SDH_COMMAND */ - -#define CMD_IDX 0x3f /* Command Index */ -#define CMD_RSP 0x40 /* Response */ -#define CMD_L_RSP 0x80 /* Long Response */ -#define CMD_INT_E 0x100 /* Command Interrupt */ -#define CMD_PEND_E 0x200 /* Command Pending */ -#define CMD_E 0x400 /* Command Enable */ - -/* Bit masks for SDH_PWR_CTL */ - -#define PWR_ON 0x3 /* Power On */ -#if 0 -#define TBD 0x3c /* TBD */ -#endif -#define SD_CMD_OD 0x40 /* Open Drain Output */ -#define ROD_CTL 0x80 /* Rod Control */ - -/* Bit masks for SDH_CLK_CTL */ - -#define CLKDIV 0xff /* MC_CLK Divisor */ -#define CLK_E 0x100 /* MC_CLK Bus Clock Enable */ -#define PWR_SV_E 0x200 /* Power Save Enable */ -#define CLKDIV_BYPASS 0x400 /* Bypass Divisor */ -#define WIDE_BUS 0x800 /* Wide Bus Mode Enable */ - -/* Bit masks for SDH_RESP_CMD */ - -#define RESP_CMD 0x3f /* Response Command */ - -/* Bit masks for SDH_DATA_CTL */ - -#define DTX_E 0x1 /* Data Transfer Enable */ -#define DTX_DIR 0x2 /* Data Transfer Direction */ -#define DTX_MODE 0x4 /* Data Transfer Mode */ -#define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */ -#define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */ - -/* Bit masks for SDH_STATUS */ - -#define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */ -#define DAT_CRC_FAIL 0x2 /* Data CRC Fail */ -#define CMD_TIME_OUT 0x4 /* CMD Time Out */ -#define DAT_TIME_OUT 0x8 /* Data Time Out */ -#define TX_UNDERRUN 0x10 /* Transmit Underrun */ -#define RX_OVERRUN 0x20 /* Receive Overrun */ -#define CMD_RESP_END 0x40 /* CMD Response End */ -#define CMD_SENT 0x80 /* CMD Sent */ -#define DAT_END 0x100 /* Data End */ -#define START_BIT_ERR 0x200 /* Start Bit Error */ -#define DAT_BLK_END 0x400 /* Data Block End */ -#define CMD_ACT 0x800 /* CMD Active */ -#define TX_ACT 0x1000 /* Transmit Active */ -#define RX_ACT 0x2000 /* Receive Active */ -#define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */ -#define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */ -#define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */ -#define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */ -#define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */ -#define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */ -#define TX_DAT_RDY 0x100000 /* Transmit Data Available */ -#define RX_FIFO_RDY 0x200000 /* Receive Data Available */ - -/* Bit masks for SDH_STATUS_CLR */ - -#define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */ -#define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */ -#define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */ -#define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */ -#define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */ -#define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */ -#define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */ -#define CMD_SENT_STAT 0x80 /* CMD Sent Status */ -#define DAT_END_STAT 0x100 /* Data End Status */ -#define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */ -#define DAT_BLK_END_STAT 0x400 /* Data Block End Status */ - -/* Bit masks for SDH_MASK0 */ - -#define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */ -#define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */ -#define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */ -#define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */ -#define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */ -#define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */ -#define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */ -#define CMD_SENT_MASK 0x80 /* CMD Sent Mask */ -#define DAT_END_MASK 0x100 /* Data End Mask */ -#define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */ -#define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */ -#define CMD_ACT_MASK 0x800 /* CMD Active Mask */ -#define TX_ACT_MASK 0x1000 /* Transmit Active Mask */ -#define RX_ACT_MASK 0x2000 /* Receive Active Mask */ -#define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */ -#define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */ -#define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */ -#define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */ -#define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */ -#define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */ -#define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */ -#define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */ - -/* Bit masks for SDH_FIFO_CNT */ - -#define FIFO_COUNT 0x7fff /* FIFO Count */ - -/* Bit masks for SDH_E_STATUS */ - -#define SDIO_INT_DET 0x2 /* SDIO Int Detected */ -#define SD_CARD_DET 0x10 /* SD Card Detect */ - -/* Bit masks for SDH_E_MASK */ - -#define SDIO_MSK 0x2 /* Mask SDIO Int Detected */ -#define SCD_MSK 0x40 /* Mask Card Detect */ - -/* Bit masks for SDH_CFG */ - -#define CLKS_EN 0x1 /* Clocks Enable */ -#define SD4E 0x4 /* SDIO 4-Bit Enable */ -#define MWE 0x8 /* Moving Window Enable */ -#define SD_RST 0x10 /* SDMMC Reset */ -#define PUP_SDDAT 0x20 /* Pull-up SD_DAT */ -#define PUP_SDDAT3 0x40 /* Pull-up SD_DAT3 */ -#define PD_SDDAT3 0x80 /* Pull-down SD_DAT3 */ - -/* Bit masks for SDH_RD_WAIT_EN */ - -#define RWR 0x1 /* Read Wait Request */ - /* Bit masks for ATAPI_CONTROL */ #define PIO_START 0x1 /* Start PIO/Reg Op */ diff --git a/arch/blackfin/mach-bf548/include/mach/defBF547.h b/arch/blackfin/mach-bf548/include/mach/defBF547.h index 3d131065f8e6..be21ba5b3aa8 100644 --- a/arch/blackfin/mach-bf548/include/mach/defBF547.h +++ b/arch/blackfin/mach-bf548/include/mach/defBF547.h @@ -646,136 +646,6 @@ #define KPAD_SOFTEVAL_E 0x2 /* Software Programmable Force Evaluate */ -/* Bit masks for SDH_COMMAND */ - -#define CMD_IDX 0x3f /* Command Index */ -#define CMD_RSP 0x40 /* Response */ -#define CMD_L_RSP 0x80 /* Long Response */ -#define CMD_INT_E 0x100 /* Command Interrupt */ -#define CMD_PEND_E 0x200 /* Command Pending */ -#define CMD_E 0x400 /* Command Enable */ - -/* Bit masks for SDH_PWR_CTL */ - -#define PWR_ON 0x3 /* Power On */ -#if 0 -#define TBD 0x3c /* TBD */ -#endif -#define SD_CMD_OD 0x40 /* Open Drain Output */ -#define ROD_CTL 0x80 /* Rod Control */ - -/* Bit masks for SDH_CLK_CTL */ - -#define CLKDIV 0xff /* MC_CLK Divisor */ -#define CLK_E 0x100 /* MC_CLK Bus Clock Enable */ -#define PWR_SV_E 0x200 /* Power Save Enable */ -#define CLKDIV_BYPASS 0x400 /* Bypass Divisor */ -#define WIDE_BUS 0x800 /* Wide Bus Mode Enable */ - -/* Bit masks for SDH_RESP_CMD */ - -#define RESP_CMD 0x3f /* Response Command */ - -/* Bit masks for SDH_DATA_CTL */ - -#define DTX_E 0x1 /* Data Transfer Enable */ -#define DTX_DIR 0x2 /* Data Transfer Direction */ -#define DTX_MODE 0x4 /* Data Transfer Mode */ -#define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */ -#define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */ - -/* Bit masks for SDH_STATUS */ - -#define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */ -#define DAT_CRC_FAIL 0x2 /* Data CRC Fail */ -#define CMD_TIME_OUT 0x4 /* CMD Time Out */ -#define DAT_TIME_OUT 0x8 /* Data Time Out */ -#define TX_UNDERRUN 0x10 /* Transmit Underrun */ -#define RX_OVERRUN 0x20 /* Receive Overrun */ -#define CMD_RESP_END 0x40 /* CMD Response End */ -#define CMD_SENT 0x80 /* CMD Sent */ -#define DAT_END 0x100 /* Data End */ -#define START_BIT_ERR 0x200 /* Start Bit Error */ -#define DAT_BLK_END 0x400 /* Data Block End */ -#define CMD_ACT 0x800 /* CMD Active */ -#define TX_ACT 0x1000 /* Transmit Active */ -#define RX_ACT 0x2000 /* Receive Active */ -#define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */ -#define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */ -#define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */ -#define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */ -#define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */ -#define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */ -#define TX_DAT_RDY 0x100000 /* Transmit Data Available */ -#define RX_FIFO_RDY 0x200000 /* Receive Data Available */ - -/* Bit masks for SDH_STATUS_CLR */ - -#define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */ -#define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */ -#define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */ -#define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */ -#define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */ -#define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */ -#define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */ -#define CMD_SENT_STAT 0x80 /* CMD Sent Status */ -#define DAT_END_STAT 0x100 /* Data End Status */ -#define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */ -#define DAT_BLK_END_STAT 0x400 /* Data Block End Status */ - -/* Bit masks for SDH_MASK0 */ - -#define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */ -#define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */ -#define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */ -#define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */ -#define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */ -#define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */ -#define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */ -#define CMD_SENT_MASK 0x80 /* CMD Sent Mask */ -#define DAT_END_MASK 0x100 /* Data End Mask */ -#define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */ -#define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */ -#define CMD_ACT_MASK 0x800 /* CMD Active Mask */ -#define TX_ACT_MASK 0x1000 /* Transmit Active Mask */ -#define RX_ACT_MASK 0x2000 /* Receive Active Mask */ -#define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */ -#define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */ -#define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */ -#define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */ -#define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */ -#define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */ -#define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */ -#define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */ - -/* Bit masks for SDH_FIFO_CNT */ - -#define FIFO_COUNT 0x7fff /* FIFO Count */ - -/* Bit masks for SDH_E_STATUS */ - -#define SDIO_INT_DET 0x2 /* SDIO Int Detected */ -#define SD_CARD_DET 0x10 /* SD Card Detect */ - -/* Bit masks for SDH_E_MASK */ - -#define SDIO_MSK 0x2 /* Mask SDIO Int Detected */ -#define SCD_MSK 0x40 /* Mask Card Detect */ - -/* Bit masks for SDH_CFG */ - -#define CLKS_EN 0x1 /* Clocks Enable */ -#define SD4E 0x4 /* SDIO 4-Bit Enable */ -#define MWE 0x8 /* Moving Window Enable */ -#define SD_RST 0x10 /* SDMMC Reset */ -#define PUP_SDDAT 0x20 /* Pull-up SD_DAT */ -#define PUP_SDDAT3 0x40 /* Pull-up SD_DAT3 */ -#define PD_SDDAT3 0x80 /* Pull-down SD_DAT3 */ - -/* Bit masks for SDH_RD_WAIT_EN */ - -#define RWR 0x1 /* Read Wait Request */ - /* Bit masks for ATAPI_CONTROL */ #define PIO_START 0x1 /* Start PIO/Reg Op */ |