diff options
| -rw-r--r-- | Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt | 75 | ||||
| -rw-r--r-- | MAINTAINERS | 7 | ||||
| -rw-r--r-- | drivers/pci/host/Kconfig | 6 | ||||
| -rw-r--r-- | drivers/pci/host/Makefile | 1 | ||||
| -rw-r--r-- | drivers/pci/host/pci-v3-semi.c | 959 |
5 files changed, 1041 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt index 30b364e504ba..11063293f761 100644 --- a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt +++ b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt @@ -2,14 +2,75 @@ V3 Semiconductor V360 EPC PCI bridge This bridge is found in the ARM Integrator/AP (Application Platform) -Integrator-specific notes: +Required properties: +- compatible: should be one of: + "v3,v360epc-pci" + "arm,integrator-ap-pci", "v3,v360epc-pci" +- reg: should contain two register areas: + first the base address of the V3 host bridge controller, 64KB + second the configuration area register space, 16MB +- interrupts: should contain a reference to the V3 error interrupt + as routed on the system. +- bus-range: see pci.txt +- ranges: this follows the standard PCI bindings in the IEEE Std + 1275-1994 (see pci.txt) with the following restriction: + - The non-prefetchable and prefetchable memory windows must + each be exactly 256MB (0x10000000) in size. + - The prefetchable memory window must be immediately adjacent + to the non-prefetcable memory window +- dma-ranges: three ranges for the inbound memory region. The ranges must + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, + 64MB, 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked + as pre-fetchable. Two ranges are supported by the hardware. -- syscon: should contain a link to the syscon device node (since +Integrator-specific required properties: +- syscon: should contain a link to the syscon device node, since on the Integrator, some registers in the syscon are required to - operate the V3). + operate the V3 host bridge. -V360 EPC specific notes: +Example: -- reg: should contain the base address of the V3 adapter. -- interrupts: should contain a reference to the V3 error interrupt - as routed on the system. +pci: pciv3@62000000 { + compatible = "arm,integrator-ap-pci", "v3,v360epc-pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x62000000 0x10000>, <0x61000000 0x01000000>; + interrupt-parent = <&pic>; + interrupts = <17>; /* Bus error IRQ */ + clocks = <&pciclk>; + bus-range = <0x00 0xff>; + ranges = 0x01000000 0 0x00000000 /* I/O space @00000000 */ + 0x60000000 0 0x01000000 /* 16 MiB @ LB 60000000 */ + 0x02000000 0 0x40000000 /* non-prefectable memory @40000000 */ + 0x40000000 0 0x10000000 /* 256 MiB @ LB 40000000 1:1 */ + 0x42000000 0 0x50000000 /* prefetchable memory @50000000 */ + 0x50000000 0 0x10000000>; /* 256 MiB @ LB 50000000 1:1 */ + dma-ranges = <0x02000000 0 0x20000000 /* EBI memory space */ + 0x20000000 0 0x20000000 /* 512 MB @ LB 20000000 1:1 */ + 0x02000000 0 0x80000000 /* Core module alias memory */ + 0x80000000 0 0x40000000>; /* 1GB @ LB 80000000 */ + interrupt-map-mask = <0xf800 0 0 0x7>; + interrupt-map = < + /* IDSEL 9 */ + 0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */ + 0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */ + 0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */ + 0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */ + /* IDSEL 10 */ + 0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */ + 0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */ + 0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */ + 0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */ + /* IDSEL 11 */ + 0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */ + 0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */ + 0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */ + 0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */ + /* IDSEL 12 */ + 0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */ + 0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */ + 0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */ + 0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */ + >; +}; diff --git a/MAINTAINERS b/MAINTAINERS index 2a3501cfd201..ca456a870731 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10511,6 +10511,13 @@ S: Maintained F: Documentation/devicetree/bindings/pci/rockchip-pcie.txt F: drivers/pci/host/pcie-rockchip.c +PCI DRIVER FOR V3 SEMICONDUCTOR V360EPC +M: Linus Walleij <linus.walleij@linaro.org> +L: linux-pci@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt +F: drivers/pci/host/pci-v3-semi.c + PCIE DRIVER FOR ST SPEAR13XX M: Pratyush Anand <pratyush.anand@gmail.com> L: linux-pci@vger.kernel.org diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig index b868803792d8..38d12980db0f 100644 --- a/drivers/pci/host/Kconfig +++ b/drivers/pci/host/Kconfig @@ -95,6 +95,12 @@ config PCI_XGENE_MSI Say Y here if you want PCIe MSI support for the APM X-Gene v1 SoC. This MSI driver supports 5 PCIe ports on the APM X-Gene v1 SoC. +config PCI_V3_SEMI + bool "V3 Semiconductor PCI controller" + depends on OF + depends on ARM + default ARCH_INTEGRATOR_AP + config PCI_VERSATILE bool "ARM Versatile PB PCI controller" depends on ARCH_VERSATILE diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile index 12382785e02a..ee7cd492bb7f 100644 --- a/drivers/pci/host/Makefile +++ b/drivers/pci/host/Makefile @@ -9,6 +9,7 @@ obj-$(CONFIG_PCI_HOST_COMMON) += pci-host-common.o obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o obj-$(CONFIG_PCIE_XILINX_NWL) += pcie-xilinx-nwl.o +obj-$(CONFIG_PCI_V3_SEMI) += pci-v3-semi.o obj-$(CONFIG_PCI_XGENE_MSI) += pci-xgene-msi.o obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o diff --git a/drivers/pci/host/pci-v3-semi.c b/drivers/pci/host/pci-v3-semi.c new file mode 100644 index 000000000000..02f6e1e3a421 --- /dev/null +++ b/drivers/pci/host/pci-v3-semi.c @@ -0,0 +1,959 @@ +/* + * Support for V3 Semiconductor PCI Local Bus to PCI Bridge + * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org> + * + * Based on the code from arch/arm/mach-integrator/pci_v3.c + * Copyright (C) 1999 ARM Limited + * Copyright (C) 2000-2001 Deep Blue Solutions Ltd + * + * Contributors to the old driver include: + * Russell King <linux@armlinux.org.uk> + * David A. Rusling <david.rusling@linaro.org> (uHAL, ARM Firmware suite) + * Rob Herring <robh@kernel.org> + * Liviu Dudau <Liviu.Dudau@arm.com> + * Grant Likely <grant.likely@secretlab.ca> + * Arnd Bergmann <arnd@arndb.de> + * Bjorn Helgaas <bhelgaas@google.com> + */ +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> +#include <linux/of_pci.h> +#include <linux/pci.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/bitops.h> +#include <linux/irq.h> +#include <linux/mfd/syscon.h> +#include <linux/regmap.h> +#include <linux/clk.h> + +#define V3_PCI_VENDOR 0x00000000 +#define V3_PCI_DEVICE 0x00000002 +#define V3_PCI_CMD 0x00000004 +#define V3_PCI_STAT 0x00000006 +#define V3_PCI_CC_REV 0x00000008 +#define V3_PCI_HDR_CFG 0x0000000C +#define V3_PCI_IO_BASE 0x00000010 +#define V3_PCI_BASE0 0x00000014 +#define V3_PCI_BASE1 0x00000018 +#define V3_PCI_SUB_VENDOR 0x0000002C +#define V3_PCI_SUB_ID 0x0000002E +#define V3_PCI_ROM 0x00000030 +#define V3_PCI_BPARAM 0x0000003C +#define V3_PCI_MAP0 0x00000040 +#define V3_PCI_MAP1 0x00000044 +#define V3_PCI_INT_STAT 0x00000048 +#define V3_PCI_INT_CFG 0x0000004C +#define V3_LB_BASE0 0x00000054 +#define V3_LB_BASE1 0x00000058 +#define V3_LB_MAP0 0x0000005E +#define V3_LB_MAP1 0x00000062 +#define V3_LB_BASE2 0x00000064 +#define V3_LB_MAP2 0x00000066 +#define V3_LB_SIZE 0x00000068 +#define V3_LB_IO_BASE 0x0000006E +#define V3_FIFO_CFG 0x00000070 +#define V3_FIFO_PRIORITY 0x00000072 +#define V3_FIFO_STAT 0x00000074 +#define V3_LB_ISTAT 0x00000076 +#define V3_LB_IMASK 0x00000077 +#define V3_SYSTEM 0x00000078 +#define V3_LB_CFG 0x0000007A +#define V3_PCI_CFG 0x0000007C +#define V3_DMA_PCI_ADR0 0x00000080 +#define V3_DMA_PCI_ADR1 0x00000090 +#define V3_DMA_LOCAL_ADR0 0x00000084 +#define V3_DMA_LOCAL_ADR1 0x00000094 +#define V3_DMA_LENGTH0 0x00000088 +#define V3_DMA_LENGTH1 0x00000098 +#define V3_DMA_CSR0 0x0000008B +#define V3_DMA_CSR1 0x0000009B +#define V3_DMA_CTLB_ADR0 0x0000008C +#define V3_DMA_CTLB_ADR1 0x0000009C +#define V3_DMA_DELAY 0x000000E0 +#define V3_MAIL_DATA 0x000000C0 +#define V3_PCI_MAIL_IEWR 0x000000D0 +#define V3_PCI_MAIL_IERD 0x000000D2 +#define V3_LB_MAIL_IEWR 0x000000D4 +#define V3_LB_MAIL_IERD 0x000000D6 +#define V3_MAIL_WR_STAT 0x000000D8 +#define V3_MAIL_RD_STAT 0x000000DA +#define V3_QBA_MAP 0x000000DC + +/* PCI STATUS bits */ +#define V3_PCI_STAT_PAR_ERR BIT(15) +#define V3_PCI_STAT_SYS_ERR BIT(14) +#define V3_PCI_STAT_M_ABORT_ERR BIT(13) +#define V3_PCI_STAT_T_ABORT_ERR BIT(12) + +/* LB ISTAT bits */ +#define V3_LB_ISTAT_MAILBOX BIT(7) +#define V3_LB_ISTAT_PCI_RD BIT(6) +#define V3_LB_ISTAT_PCI_WR BIT(5) +#define V3_LB_ISTAT_PCI_INT BIT(4) +#define V3_LB_ISTAT_PCI_PERR BIT(3) +#define V3_LB_ISTAT_I2O_QWR BIT(2) +#define V3_LB_ISTAT_DMA1 BIT(1) +#define V3_LB_ISTAT_DMA0 BIT(0) + +/* PCI COMMAND bits */ +#define V3_COMMAND_M_FBB_EN BIT(9) +#define V3_COMMAND_M_SERR_EN BIT(8) +#define V3_COMMAND_M_PAR_EN BIT(6) +#define V3_COMMAND_M_MASTER_EN BIT(2) +#define V3_COMMAND_M_MEM_EN BIT(1) +#define V3_COMMAND_M_IO_EN BIT(0) + +/* SYSTEM bits */ +#define V3_SYSTEM_M_RST_OUT BIT(15) +#define V3_SYSTEM_M_LOCK BIT(14) +#define V3_SYSTEM_UNLOCK 0xa05f + +/* PCI CFG bits */ +#define V3_PCI_CFG_M_I2O_EN BIT(15) +#define V3_PCI_CFG_M_IO_REG_DIS BIT(14) +#define V3_PCI_CFG_M_IO_DIS BIT(13) +#define V3_PCI_CFG_M_EN3V BIT(12) +#define V3_PCI_CFG_M_RETRY_EN BIT(10) +#define V3_PCI_CFG_M_AD_LOW1 BIT(9) +#define V3_PCI_CFG_M_AD_LOW0 BIT(8) +/* + * This is the value applied to C/BE[3:1], with bit 0 always held 0 + * during DMA access. + */ +#define V3_PCI_CFG_M_RTYPE_SHIFT 5 +#define V3_PCI_CFG_M_WTYPE_SHIFT 1 +#define V3_PCI_CFG_TYPE_DEFAULT 0x3 + +/* PCI BASE bits (PCI -> Local Bus) */ +#define V3_PCI_BASE_M_ADR_BASE 0xFFF00000U +#define V3_PCI_BASE_M_ADR_BASEL 0x000FFF00U +#define V3_PCI_BASE_M_PREFETCH BIT(3) +#define V3_PCI_BASE_M_TYPE (3 << 1) +#define V3_PCI_BASE_M_IO BIT(0) + +/* PCI MAP bits (PCI -> Local bus) */ +#define V3_PCI_MAP_M_MAP_ADR 0xFFF00000U +#define V3_PCI_MAP_M_RD_POST_INH BIT(15) +#define V3_PCI_MAP_M_ROM_SIZE (3 << 10) +#define V3_PCI_MAP_M_SWAP (3 << 8) +#define V3_PCI_MAP_M_ADR_SIZE 0x000000F0U +#define V3_PCI_MAP_M_REG_EN BIT(1) +#define V3_PCI_MAP_M_ENABLE BIT(0) + +/* LB_BASE0,1 bits (Local bus -> PCI) */ +#define V3_LB_BASE_ADR_BASE 0xfff00000U +#define V3_LB_BASE_SWAP (3 << 8) +#define V3_LB_BASE_ADR_SIZE (15 << 4) +#define V3_LB_BASE_PREFETCH BIT(3) +#define V3_LB_BASE_ENABLE BIT(0) + +#define V3_LB_BASE_ADR_SIZE_1MB (0 << 4) +#define V3_LB_BASE_ADR_SIZE_2MB (1 << 4) +#define V3_LB_BASE_ADR_SIZE_4MB (2 << 4) +#define V3_LB_BASE_ADR_SIZE_8MB (3 << 4) +#define V3_LB_BASE_ADR_SIZE_16MB (4 << 4) +#define V3_LB_BASE_ADR_SIZE_32MB (5 << 4) +#define V3_LB_BASE_ADR_SIZE_64MB (6 << 4) +#define V3_LB_BASE_ADR_SIZE_128MB (7 << 4) +#define V3_LB_BASE_ADR_SIZE_256MB (8 << 4) +#define V3_LB_BASE_ADR_SIZE_512MB (9 << 4) +#define V3_LB_BASE_ADR_SIZE_1GB (10 << 4) +#define V3_LB_BASE_ADR_SIZE_2GB (11 << 4) + +#define v3_addr_to_lb_base(a) ((a) & V3_LB_BASE_ADR_BASE) + +/* LB_MAP0,1 bits (Local bus -> PCI) */ +#define V3_LB_MAP_MAP_ADR 0xfff0U +#define V3_LB_MAP_TYPE (7 << 1) +#define V3_LB_MAP_AD_LOW_EN BIT(0) + +#define V3_LB_MAP_TYPE_IACK (0 << 1) +#define V3_LB_MAP_TYPE_IO (1 << 1) +#define V3_LB_MAP_TYPE_MEM (3 << 1) +#define V3_LB_MAP_TYPE_CONFIG (5 << 1) +#define V3_LB_MAP_TYPE_MEM_MULTIPLE (6 << 1) + +#define v3_addr_to_lb_map(a) (((a) >> 16) & V3_LB_MAP_MAP_ADR) + +/* LB_BASE2 bits (Local bus -> PCI IO) */ +#define V3_LB_BASE2_ADR_BASE 0xff00U +#define V3_LB_BASE2_SWAP_AUTO (3 << 6) +#define V3_LB_BASE2_ENABLE BIT(0) + +#define v3_addr_to_lb_base2(a) (((a) >> 16) & V3_LB_BASE2_ADR_BASE) + +/* LB_MAP2 bits (Local bus -> PCI IO) */ +#define V3_LB_MAP2_MAP_ADR 0xff00U + +#define v3_addr_to_lb_map2(a) (((a) >> 16) & V3_LB_MAP2_MAP_ADR) + +/* FIFO priority bits */ +#define V3_FIFO_PRIO_LOCAL BIT(12) +#define V3_FIFO_PRIO_LB_RD1_FLUSH_EOB BIT(10) +#define V3_FIFO_PRIO_LB_RD1_FLUSH_AP1 BIT(11) +#define V3_FIFO_PRIO_LB_RD1_FLUSH_ANY (BIT(10)|BIT(11)) +#define V3_FIFO_PRIO_LB_RD0_FLUSH_EOB BIT(8) +#define V3_FIFO_PRIO_LB_RD0_FLUSH_AP1 BIT(9) +#define V3_FIFO_PRIO_LB_RD0_FLUSH_ANY (BIT(8)|BIT(9)) +#define V3_FIFO_PRIO_PCI BIT(4) +#define V3_FIFO_PRIO_PCI_RD1_FLUSH_EOB BIT(2) +#define V3_FIFO_PRIO_PCI_RD1_FLUSH_AP1 BIT(3) +#define V3_FIFO_PRIO_PCI_RD1_FLUSH_ANY (BIT(2)|BIT(3)) +#define V3_FIFO_PRIO_PCI_RD0_FLUSH_EOB BIT(0) +#define V3_FIFO_PRIO_PCI_RD0_FLUSH_AP1 BIT(1) +#define V3_FIFO_PRIO_PCI_RD0_FLUSH_ANY (BIT(0)|BIT(1)) + +/* Local bus configuration bits */ +#define V3_LB_CFG_LB_TO_64_CYCLES 0x0000 +#define V3_LB_CFG_LB_TO_256_CYCLES BIT(13) +#define V3_LB_CFG_LB_TO_512_CYCLES BIT(14) +#define V3_LB_CFG_LB_TO_1024_CYCLES (BIT(13)|BIT(14)) +#define V3_LB_CFG_LB_RST BIT(12) +#define V3_LB_CFG_LB_PPC_RDY BIT(11) +#define V3_LB_CFG_LB_LB_INT BIT(10) +#define V3_LB_CFG_LB_ERR_EN BIT(9) +#define V3_LB_CFG_LB_RDY_EN BIT(8) +#define V3_LB_CFG_LB_BE_IMODE BIT(7) +#define V3_LB_CFG_LB_BE_OMODE BIT(6) +#define V3_LB_CFG_LB_ENDIAN BIT(5) +#define V3_LB_CFG_LB_PARK_EN BIT(4) +#define V3_LB_CFG_LB_FBB_DIS BIT(2) + +/* ARM Integrator-specific extended control registers */ +#define INTEGRATOR_SC_PCI_OFFSET 0x18 +#define INTEGRATOR_SC_PCI_ENABLE BIT(0) +#define INTEGRATOR_SC_PCI_INTCLR BIT(1) +#define INTEGRATOR_SC_LBFADDR_OFFSET 0x20 +#define INTEGRATOR_SC_LBFCODE_OFFSET 0x24 + +struct v3_pci { + struct device *dev; + void __iomem *base; + void __iomem *config_base; + struct pci_bus *bus; + u32 config_mem; + u32 io_mem; + u32 non_pre_mem; + u32 pre_mem; + phys_addr_t io_bus_addr; + phys_addr_t non_pre_bus_addr; + phys_addr_t pre_bus_addr; + struct regmap *map; +}; + +/* + * The V3 PCI interface chip in Integrator provides several windows from + * local bus memory into the PCI memory areas. Unfortunately, there + * are not really enough windows for our usage, therefore we reuse + * one of the windows for access to PCI configuration space. On the + * Integrator/AP, the memory map is as follows: + * + * Local Bus Memory Usage + * + * 40000000 - 4FFFFFFF PCI memory. 256M non-prefetchable + * 50000000 - 5FFFFFFF PCI memory. 256M prefetchable + * 60000000 - 60FFFFFF PCI IO. 16M + * 61000000 - 61FFFFFF PCI Configuration. 16M + * + * There are three V3 windows, each described by a pair of V3 registers. + * These are LB_BASE0/LB_MAP0, LB_BASE1/LB_MAP1 and LB_BASE2/LB_MAP2. + * Base0 and Base1 can be used for any type of PCI memory access. Base2 + * can be used either for PCI I/O or for I20 accesses. By default, uHAL + * uses this only for PCI IO space. + * + * Normally these spaces are mapped using the following base registers: + * + * Usage Local Bus Memory Base/Map registers used + * + * Mem 40000000 - 4FFFFFFF LB_BASE0/LB_MAP0 + * Mem 50000000 - 5FFFFFFF LB_BASE1/LB_MAP1 + * IO 60000000 - 60FFFFFF LB_BASE2/LB_MAP2 + * Cfg 61000000 - 61FFFFFF + * + * This means that I20 and PCI configuration space accesses will fail. + * When PCI configuration accesses are needed (via the uHAL PCI + * configuration space primitives) we must remap the spaces as follows: + * + * Usage Local Bus Memory Base/Map registers used + * + * Mem 40000000 - 4FFFFFFF LB_BASE0/LB_MAP0 + * Mem 50000000 - 5FFFFFFF LB_BASE0/LB_MAP0 + * IO 60000000 - 60FFFFFF LB_BASE2/LB_MAP2 + * Cfg 61000000 - 61FFFFFF LB_BASE1/LB_MAP1 + * + * To make this work, the code depends on overlapping windows working. + * The V3 chip translates an address by checking its range within + * each of the BASE/MAP pairs in turn (in ascending register number + * order). It will use the first matching pair. So, for example, + * if the same address is mapped by both LB_BASE0/LB_MAP0 and + * LB_BASE1/LB_MAP1, the V3 will use the translation from + * LB_BASE0/LB_MAP0. + * + * To allow PCI Configuration space access, the code enlarges the + * window mapped by LB_BASE0/LB_MAP0 from 256M to 512M. This occludes + * the windows currently mapped by LB_BASE1/LB_MAP1 so that it can + * be remapped for use by configuration cycles. + * + * At the end of the PCI Configuration space accesses, + * LB_BASE1/LB_MAP1 is reset to map PCI Memory. Finally the window + * mapped by LB_BASE0/LB_MAP0 is reduced in size from 512M to 256M to + * reveal the now restored LB_BASE1/LB_MAP1 window. + * + * NOTE: We do not set up I2O mapping. I suspect that this is only + * for an intelligent (target) device. Using I2O disables most of + * the mappings into PCI memory. + */ +static void __iomem *v3_map_bus(struct pci_bus *bus, + unsigned int devfn, int offset) +{ + struct v3_pci *v3 = bus->sysdata; + unsigned int address, mapaddress, busnr; + + busnr = bus->number; + if (busnr == 0) { + int slot = PCI_SLOT(devfn); + + /* + * local bus segment so need a type 0 config cycle + * + * build the PCI configuration "address" with one-hot in + * A31-A11 + * + * mapaddress: + * 3:1 = config cycle (101) + * 0 = PCI A1 & A0 are 0 (0) + */ + address = PCI_FUNC(devfn) << 8; + mapaddress = V3_LB_MAP_TYPE_CONFIG; + + if (slot > 12) + /* + * high order bits are handled by the MAP register + */ + mapaddress |= BIT(slot - 5); + else + /* + * low order bits handled directly in the address + */ + address |= BIT(slot + 11); + } else { + /* + * not the local bus segment so need a type 1 config cycle + * + * address: + * 23:16 = bus number + * 15:11 = slot number (7:3 of devfn) + * 10:8 = func number (2:0 of devfn) + * + * mapaddress: + * 3:1 = config cycle (101) + * 0 = PCI A1 & A0 from host bus (1) + */ + mapaddress = V3_LB_MAP_TYPE_CONFIG | V3_LB_MAP_AD_LOW_EN; + address = (busnr << 16) | (devfn << 8); + } + + /* + * Set up base0 to see all 512Mbytes of memory space (not + * prefetchable), this frees up base1 for re-use by + * configuration memory + */ + writel(v3_addr_to_lb_base(v3->non_pre_mem) | + V3_LB_BASE_ADR_SIZE_512MB | V3_LB_BASE_ENABLE, + v3->base + V3_LB_BASE0); + + /* + * Set up base1/map1 to point into configuration space. + * The config mem is always 16MB. + */ + writel(v3_addr_to_lb_base(v3->config_mem) | + V3_LB_BASE_ADR_SIZE_16MB | V3_LB_BASE_ENABLE, + v3->base + V3_LB_BASE1); + writew(mapaddress, v3->base + V3_LB_MAP1); + + return v3->config_base + address + offset; +} + +static void v3_unmap_bus(struct v3_pci *v3) +{ + /* + * Reassign base1 for use by prefetchable PCI memory + */ + writel(v3_addr_to_lb_base(v3->pre_mem) | + V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH | + V3_LB_BASE_ENABLE, + v3->base + V3_LB_BASE1); + writew(v3_addr_to_lb_map(v3->pre_bus_addr) | + V3_LB_MAP_TYPE_MEM, /* was V3_LB_MAP_TYPE_MEM_MULTIPLE */ + v3->base + V3_LB_MAP1); + + /* + * And shrink base0 back to a 256M window (NOTE: MAP0 already correct) + */ + writel(v3_addr_to_lb_base(v3->non_pre_mem) | + V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE, + v3->base + V3_LB_BASE0); +} + +static int v3_pci_read_config(struct pci_bus *bus, unsigned int fn, + int config, int size, u32 *value) +{ + struct v3_pci *v3 = bus->sysdata; + int ret; + + dev_dbg(&bus->dev, + "[read] slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n", + PCI_SLOT(fn), PCI_FUNC(fn), config, size, *value); + ret = pci_generic_config_read(bus, fn, config, size, value); + v3_unmap_bus(v3); + return ret; +} + +static int v3_pci_write_config(struct pci_bus *bus, unsigned int fn, + int config, int size, u32 value) +{ + struct v3_pci *v3 = bus->sysdata; + int ret; + + dev_dbg(&bus->dev, + "[write] slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n", + PCI_SLOT(fn), PCI_FUNC(fn), config, size, value); + ret = pci_generic_config_write(bus, fn, config, size, value); + v3_unmap_bus(v3); + return ret; +} + +static struct pci_ops v3_pci_ops = { + .map_bus = v3_map_bus, + .read = v3_pci_read_config, + .write = v3_pci_write_config, +}; + +static irqreturn_t v3_irq(int irq, void *data) +{ + struct v3_pci *v3 = data; + struct device *dev = v3->dev; + u32 status; + + status = readw(v3->base + V3_PCI_STAT); + if (status & V3_PCI_STAT_PAR_ERR) + dev_err(dev, "parity error interrupt\n"); + if (status & V3_PCI_STAT_SYS_ERR) + dev_err(dev, "system error interrupt\n"); + if (status & V3_PCI_STAT_M_ABORT_ERR) + dev_err(dev, "master abort error interrupt\n"); + if (status & V3_PCI_STAT_T_ABORT_ERR) + dev_err(dev, "target abort error interrupt\n"); + writew(status, v3->base + V3_PCI_STAT); + + status = readb(v3->base + V3_LB_ISTAT); + if (status & V3_LB_ISTAT_MAILBOX) + dev_info(dev, "PCI mailbox interrupt\n"); + if (status & V3_LB_ISTAT_PCI_RD) + dev_err(dev, "PCI target LB->PCI READ abort interrupt\n"); + if (status & V3_LB_ISTAT_PCI_WR) + dev_err(dev, "PCI target LB->PCI WRITE abort interrupt\n"); + if (status & V3_LB_ISTAT_PCI_INT) + dev_info(dev, "PCI pin interrupt\n"); + if (status & V3_LB_ISTAT_PCI_PERR) + dev_err(dev, "PCI parity error interrupt\n"); + if (status & V3_LB_ISTAT_I2O_QWR) + dev_info(dev, "I2O inbound post queue interrupt\n"); + if (status & V3_LB_ISTAT_DMA1) + dev_info(dev, "DMA channel 1 interrupt\n"); + if (status & V3_LB_ISTAT_DMA0) + dev_info(dev, "DMA channel 0 interrupt\n"); + /* Clear all possible interrupts on the local bus */ + writeb(0, v3->base + V3_LB_ISTAT); + if (v3->map) + regmap_write(v3->map, INTEGRATOR_SC_PCI_OFFSET, + INTEGRATOR_SC_PCI_ENABLE | + INTEGRATOR_SC_PCI_INTCLR); + + return IRQ_HANDLED; +} + +static int v3_integrator_init(struct v3_pci *v3) +{ + unsigned int val; + + v3->map = + syscon_regmap_lookup_by_compatible("arm,integrator-ap-syscon"); + if (IS_ERR(v3->map)) { + dev_err(v3->dev, "no syscon\n"); + return -ENODEV; + } + + regmap_read(v3->map, INTEGRATOR_SC_PCI_OFFSET, &val); + /* Take the PCI bridge out of reset, clear IRQs */ + regmap_write(v3->map, INTEGRATOR_SC_PCI_OFFSET, + INTEGRATOR_SC_PCI_ENABLE | + INTEGRATOR_SC_PCI_INTCLR); + + if (!(val & INTEGRATOR_SC_PCI_ENABLE)) { + /* If we were in reset we need to sleep a bit */ + msleep(230); + + /* Set the physical base for the controller itself */ + writel(0x6200, v3->base + V3_LB_IO_BASE); + + /* Wait for the mailbox to settle after reset */ + do { + writeb(0xaa, v3->base + V3_MAIL_DATA); + writeb(0x55, v3->base + V3_MAIL_DATA + 4); + } while (readb(v3->base + V3_MAIL_DATA) != 0xaa && + readb(v3->base + V3_MAIL_DATA) != 0x55); + } + + dev_info(v3->dev, "initialized PCI V3 Integrator/AP integration\n"); + + return 0; +} + +static int v3_pci_setup_resource(struct v3_pci *v3, + resource_size_t io_base, + struct pci_host_bridge *host, + struct resource_entry *win) +{ + struct device *dev = v3->dev; + struct resource *mem; + struct resource *io; + int ret; + + switch (resource_type(win->res)) { + case IORESOURCE_IO: + io = win->res; + io->name = "V3 PCI I/O"; + v3->io_mem = io_base; + v3->io_bus_addr = io->start - win->offset; + dev_dbg(dev, "I/O window %pR, bus addr %pap\n", + io, &v3->io_bus_addr); + ret = pci_remap_iospace(io, io_base); + if (ret) { + dev_warn(dev, + "error %d: failed to map resource %pR\n", + ret, io); + return ret; + } + /* Setup window 2 - PCI I/O */ + writel(v3_addr_to_lb_base2(v3->io_mem) | + V3_LB_BASE2_ENABLE, + v3->base + V3_LB_BASE2); + writew(v3_addr_to_lb_map2(v3->io_bus_addr), + v3->base + V3_LB_MAP2); + break; + case IORESOURCE_MEM: + mem = win->res; + if (mem->flags & IORESOURCE_PREFETCH) { + mem->name = "V3 PCI PRE-MEM"; + v3->pre_mem = mem->start; + v3->pre_bus_addr = mem->start - win->offset; + dev_dbg(dev, "PREFETCHABLE MEM window %pR, bus addr %pap\n", + mem, &v3->pre_bus_addr); + if (resource_size(mem) != SZ_256M) { + dev_err(dev, "prefetchable memory range is not 256MB\n"); + return -EINVAL; + } + if (v3->non_pre_mem && + (mem->start != v3->non_pre_mem + SZ_256M)) { + dev_err(dev, + "prefetchable memory is not adjacent to non-prefetchable memory\n"); + return -EINVAL; + } + /* Setup window 1 - PCI prefetchable memory */ + writel(v3_addr_to_lb_base(v3->pre_mem) | + V3_LB_BASE_ADR_SIZE_256MB | + V3_LB_BASE_PREFETCH | + V3_LB_BASE_ENABLE, + v3->base + V3_LB_BASE1); + writew(v3_addr_to_lb_map(v3->pre_bus_addr) | + V3_LB_MAP_TYPE_MEM, /* Was V3_LB_MAP_TYPE_MEM_MULTIPLE */ + v3->base + V3_LB_MAP1); + } else { + mem->name = "V3 PCI NON-PRE-MEM"; + v3->non_pre_mem = mem->start; + v3->non_pre_bus_addr = mem->start - win->offset; + dev_dbg(dev, "NON-PREFETCHABLE MEM window %pR, bus addr %pap\n", + mem, &v3->non_pre_bus_addr); + if (resource_size(mem) != SZ_256M) { + dev_err(dev, + "non-prefetchable memory range is not 256MB\n"); + return -EINVAL; + } + /* Setup window 0 - PCI non-prefetchable memory */ + writel(v3_addr_to_lb_base(v3->non_pre_mem) | + V3_LB_BASE_ADR_SIZE_256MB | + V3_LB_BASE_ENABLE, + v3->base + V3_LB_BASE0); + writew(v3_addr_to_lb_map(v3->non_pre_bus_addr) | + V3_LB_MAP_TYPE_MEM, + v3->base + V3_LB_MAP0); + } + break; + case IORESOURCE_BUS: + dev_dbg(dev, "BUS %pR\n", win->res); + host->busnr = win->res->start; + break; + default: + dev_info(dev, "Unknown resource type %lu\n", + resource_type(win->res)); + break; + } + + return 0; +} + +static int v3_get_dma_range_config(struct v3_pci *v3, + struct of_pci_range *range, + u32 *pci_base, u32 *pci_map) +{ + struct device *dev = v3->dev; + u64 cpu_end = range->cpu_addr + range->size - 1; + u64 pci_end = range->pci_addr + range->size - 1; + u32 val; + + if (range->pci_addr & ~V3_PCI_BASE_M_ADR_BASE) { + dev_err(dev, "illegal range, only PCI bits 31..20 allowed\n"); + return -EINVAL; + } + val = ((u32)range->pci_addr) & V3_PCI_BASE_M_ADR_BASE; + *pci_base = val; + + if (range->cpu_addr & ~V3_PCI_MAP_M_MAP_ADR) { + dev_err(dev, "illegal range, only CPU bits 31..20 allowed\n"); + return -EINVAL; + } + val = ((u32)range->cpu_addr) & V3_PCI_MAP_M_MAP_ADR; + + switch (range->size) { + case SZ_1M: + val |= V3_LB_BASE_ADR_SIZE_1MB; + break; + case SZ_2M: + val |= V3_LB_BASE_ADR_SIZE_2MB; + break; + case SZ_4M: + val |= V3_LB_BASE_ADR_SIZE_4MB; + break; + case SZ_8M: + val |= V3_LB_BASE_ADR_SIZE_8MB; + break; + case SZ_16M: + val |= V3_LB_BASE_ADR_SIZE_16MB; + break; + case SZ_32M: + val |= V3_LB_BASE_ADR_SIZE_32MB; + break; + case SZ_64M: + val |= V3_LB_BASE_ADR_SIZE_64MB; + break; + case SZ_128M: + val |= V3_LB_BASE_ADR_SIZE_128MB; + break; + case SZ_256M: + val |= V3_LB_BASE_ADR_SIZE_256MB; + break; + case SZ_512M: + val |= V3_LB_BASE_ADR_SIZE_512MB; + break; + case SZ_1G: + val |= V3_LB_BASE_ADR_SIZE_1GB; + break; + case SZ_2G: + val |= V3_LB_BASE_ADR_SIZE_2GB; + break; + default: + dev_err(v3->dev, "illegal dma memory chunk size\n"); + return -EINVAL; + break; + }; + val |= V3_PCI_MAP_M_REG_EN | V3_PCI_MAP_M_ENABLE; + *pci_map = val; + + dev_dbg(dev, + "DMA MEM CPU: 0x%016llx -> 0x%016llx => " + "PCI: 0x%016llx -> 0x%016llx base %08x map %08x\n", + range->cpu_addr, cpu_end, + range->pci_addr, pci_end, + *pci_base, *pci_map); + + return 0; +} + +static int v3_pci_parse_map_dma_ranges(struct v3_pci *v3, + struct device_node *np) +{ + struct of_pci_range range; + struct of_pci_range_parser parser; + struct device *dev = v3->dev; + int i = 0; + + if (of_pci_dma_range_parser_init(&parser, np)) { + dev_err(dev, "missing dma-ranges property\n"); + return -EINVAL; + } + + /* + * Get the dma-ranges from the device tree + */ + for_each_of_pci_range(&parser, &range) { + int ret; + u32 pci_base, pci_map; + + ret = v3_get_dma_range_config(v3, &range, &pci_base, &pci_map); + if (ret) + return ret; + + if (i == 0) { + writel(pci_base, v3->base + V3_PCI_BASE0); + writel(pci_map, v3->base + V3_PCI_MAP0); + } else if (i == 1) { + writel(pci_base, v3->base + V3_PCI_BASE1); + writel(pci_map, v3->base + V3_PCI_MAP1); + } else { + dev_err(dev, "too many ranges, only two supported\n"); + dev_err(dev, "range %d ignored\n", i); + } + i++; + } + return 0; +} + +static int v3_pci_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + resource_size_t io_base; + struct resource *regs; + struct resource_entry *win; + struct v3_pci *v3; + struct pci_host_bridge *host; + struct clk *clk; + u16 val; + int irq; + int ret; + LIST_HEAD(res); + + host = pci_alloc_host_bridge(sizeof(*v3)); + if (!host) + return -ENOMEM; + + host->dev.parent = dev; + host->ops = &v3_pci_ops; + host->busnr = 0; + host->msi = NULL; + host->map_irq = of_irq_parse_and_map_pci; + host->swizzle_irq = pci_common_swizzle; + v3 = pci_host_bridge_priv(host); + host->sysdata = v3; + v3->dev = dev; + + /* Get and enable host clock */ + clk = devm_clk_get(dev, NULL); + if (IS_ERR(clk)) { + dev_err(dev, "clock not found\n"); + return PTR_ERR(clk); + } + ret = clk_prepare_enable(clk); + if (ret) { + dev_err(dev, "unable to enable clock\n"); + return ret; + } + + regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + v3->base = devm_ioremap_resource(dev, regs); + if (IS_ERR(v3->base)) + return PTR_ERR(v3->base); + /* + * The hardware has a register with the physical base address + * of the V3 controller itself, verify that this is the same + * as the physical memory we've remapped it from. + */ + if (readl(v3->base + V3_LB_IO_BASE) != (regs->start >> 16)) + dev_err(dev, "V3_LB_IO_BASE = %08x but device is @%pR\n", + readl(v3->base + V3_LB_IO_BASE), regs); + + /* Configuration space is 16MB directly mapped */ + regs = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (resource_size(regs) != SZ_16M) { + dev_err(dev, "config mem is not 16MB!\n"); + return -EINVAL; + } + v3->config_mem = regs->start; + v3->config_base = devm_ioremap_resource(dev, regs); + if (IS_ERR(v3->config_base)) + return PTR_ERR(v3->config_base); + + ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &io_base); + if (ret) + return ret; + + ret = devm_request_pci_bus_resources(dev, &res); + if (ret) + return ret; + + /* Get and request error IRQ resource */ + irq = platform_get_irq(pdev, 0); + if (irq <= 0) { + dev_err(dev, "unable to obtain PCIv3 error IRQ\n"); + return -ENODEV; + } + ret = devm_request_irq(dev, irq, v3_irq, 0, + "PCIv3 error", v3); + if (ret < 0) { + dev_err(dev, + "unable to request PCIv3 error IRQ %d (%d)\n", + irq, ret); + return ret; + } + + /* + * Unlock V3 registers, but only if they were previously locked. + */ + if (readw(v3->base + V3_SYSTEM) & V3_SYSTEM_M_LOCK) + writew(V3_SYSTEM_UNLOCK, v3->base + V3_SYSTEM); + + /* Disable all slave access while we set up the windows */ + val = readw(v3->base + V3_PCI_CMD); + val &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + writew(val, v3->base + V3_PCI_CMD); + + /* Put the PCI bus into reset */ + val = readw(v3->base + V3_SYSTEM); + val &= ~V3_SYSTEM_M_RST_OUT; + writew(val, v3->base + V3_SYSTEM); + + /* Retry until we're ready */ + val = readw(v3->base + V3_PCI_CFG); + val |= V3_PCI_CFG_M_RETRY_EN; + writew(val, v3->base + V3_PCI_CFG); + + /* Set up the local bus protocol */ + val = readw(v3->base + V3_LB_CFG); + val |= V3_LB_CFG_LB_BE_IMODE; /* Byte enable input */ + val |= V3_LB_CFG_LB_BE_OMODE; /* Byte enable output */ + val &= ~V3_LB_CFG_LB_ENDIAN; /* Little endian */ + val &= ~V3_LB_CFG_LB_PPC_RDY; /* TODO: when using on PPC403Gx, set to 1 */ + writew(val, v3->base + V3_LB_CFG); + + /* Enable the PCI bus master */ + val = readw(v3->base + V3_PCI_CMD); + val |= PCI_COMMAND_MASTER; + writew(val, v3->base + V3_PCI_CMD); + + /* Get the I/O and memory ranges from DT */ + resource_list_for_each_entry(win, &res) { + ret = v3_pci_setup_resource(v3, io_base, host, win); + if (ret) { + dev_err(dev, "error setting up resources\n"); + return ret; + } + } + ret = v3_pci_parse_map_dma_ranges(v3, np); + if (ret) + return ret; + + /* + * Disable PCI to host IO cycles, enable I/O buffers @3.3V, + * set AD_LOW0 to 1 if one of the LB_MAP registers choose + * to use this (should be unused). + */ + writel(0x00000000, v3->base + V3_PCI_IO_BASE); + val = V3_PCI_CFG_M_IO_REG_DIS | V3_PCI_CFG_M_IO_DIS | + V3_PCI_CFG_M_EN3V | V3_PCI_CFG_M_AD_LOW0; + /* + * DMA read and write from PCI bus commands types + */ + val |= V3_PCI_CFG_TYPE_DEFAULT << V3_PCI_CFG_M_RTYPE_SHIFT; + val |= V3_PCI_CFG_TYPE_DEFAULT << V3_PCI_CFG_M_WTYPE_SHIFT; + writew(val, v3->base + V3_PCI_CFG); + + /* + * Set the V3 FIFO such that writes have higher priority than + * reads, and local bus write causes local bus read fifo flush + * on aperture 1. Same for PCI. + */ + writew(V3_FIFO_PRIO_LB_RD1_FLUSH_AP1 | + V3_FIFO_PRIO_LB_RD0_FLUSH_AP1 | + V3_FIFO_PRIO_PCI_RD1_FLUSH_AP1 | + V3_FIFO_PRIO_PCI_RD0_FLUSH_AP1, + v3->base + V3_FIFO_PRIORITY); + + + /* + * Clear any error interrupts, and enable parity and write error + * interrupts + */ + writeb(0, v3->base + V3_LB_ISTAT); + val = readw(v3->base + V3_LB_CFG); + val |= V3_LB_CFG_LB_LB_INT; + writew(val, v3->base + V3_LB_CFG); + writeb(V3_LB_ISTAT_PCI_WR | V3_LB_ISTAT_PCI_PERR, + v3->base + V3_LB_IMASK); + + /* Special Integrator initialization */ + if (of_device_is_compatible(np, "arm,integrator-ap-pci")) { + ret = v3_integrator_init(v3); + if (ret) + return ret; + } + + /* Post-init: enable PCI memory and invalidate (master already on) */ + val = readw(v3->base + V3_PCI_CMD); + val |= PCI_COMMAND_MEMORY | PCI_COMMAND_INVALIDATE; + writew(val, v3->base + V3_PCI_CMD); + + /* Clear pending interrupts */ + writeb(0, v3->base + V3_LB_ISTAT); + /* Read or write errors and parity errors cause interrupts */ + writeb(V3_LB_ISTAT_PCI_RD | V3_LB_ISTAT_PCI_WR | V3_LB_ISTAT_PCI_PERR, + v3->base + V3_LB_IMASK); + + /* Take the PCI bus out of reset so devices can initialize */ + val = readw(v3->base + V3_SYSTEM); + val |= V3_SYSTEM_M_RST_OUT; + writew(val, v3->base + V3_SYSTEM); + + /* + * Re-lock the system register. + */ + val = readw(v3->base + V3_SYSTEM); + val |= V3_SYSTEM_M_LOCK; + writew(val, v3->base + V3_SYSTEM); + + list_splice_init(&res, &host->windows); + ret = pci_scan_root_bus_bridge(host); + if (ret) { + dev_err(dev, "failed to register host: %d\n", ret); + return ret; + } + v3->bus = host->bus; + + pci_bus_assign_resources(v3->bus); + pci_bus_add_devices(v3->bus); + + return 0; +} + +static const struct of_device_id v3_pci_of_match[] = { + { + .compatible = "v3,v360epc-pci", + }, + {}, +}; + +static struct platform_driver v3_pci_driver = { + .driver = { + .name = "pci-v3-semi", + .of_match_table = of_match_ptr(v3_pci_of_match), + .suppress_bind_attrs = true, + }, + .probe = v3_pci_probe, +}; +builtin_platform_driver(v3_pci_driver); |