summaryrefslogtreecommitdiff
path: root/drivers/tty/serial
diff options
context:
space:
mode:
authorMatt Redfearn <matt.redfearn@mips.com>2017-11-22 09:57:28 +0000
committerGreg Kroah-Hartman <gregkh@linuxfoundation.org>2017-11-28 15:55:15 +0100
commit0ff3ab701963a845d52337ded7eebf2d1a14fe00 (patch)
tree8c65c81aba654d7cd393543c92decc16f5c95ae2 /drivers/tty/serial
parent3bfd1300abfe3adb18e84a89d97a0e82a22124bb (diff)
serial: 8250_early: Only set divisor if valid clk & baud
If either uartclk or baud are 0, avoid calculating and setting a divisor based on them since the output will almost certainly be garbage. This also allows platforms such as the MIPS generic kernel, which has no way to know a valid BASE_BASE for the board it is actually booted on at compile time, to set BASE_BAUD to 0 and avoid early_8250 setting a bad divisor. This fixes a regression caused by commit 31cb9a8575ca ("earlycon: initialise baud field of earlycon device structure"), which changed the behavior of of_setup_earlycon such that it sets a baud rate in the earlycon structure where previously it was left as 0. All boards supported by the MIPS generic kernel started outputting garbage from the boot console due to an incorrect divisor being set. Fixes: 31cb9a8575ca ("earlycon: initialise baud field of earlycon device structure") Cc: stable <stable@vger.kernel.org> # 4.14 Signed-off-by: Matt Redfearn <matt.redfearn@mips.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Diffstat (limited to 'drivers/tty/serial')
-rw-r--r--drivers/tty/serial/8250/8250_early.c14
1 files changed, 8 insertions, 6 deletions
diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c
index 362c25ff188a..ae6a256524d8 100644
--- a/drivers/tty/serial/8250/8250_early.c
+++ b/drivers/tty/serial/8250/8250_early.c
@@ -122,12 +122,14 @@ static void __init init_port(struct earlycon_device *device)
serial8250_early_out(port, UART_FCR, 0); /* no fifo */
serial8250_early_out(port, UART_MCR, 0x3); /* DTR + RTS */
- divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * device->baud);
- c = serial8250_early_in(port, UART_LCR);
- serial8250_early_out(port, UART_LCR, c | UART_LCR_DLAB);
- serial8250_early_out(port, UART_DLL, divisor & 0xff);
- serial8250_early_out(port, UART_DLM, (divisor >> 8) & 0xff);
- serial8250_early_out(port, UART_LCR, c & ~UART_LCR_DLAB);
+ if (port->uartclk && device->baud) {
+ divisor = DIV_ROUND_CLOSEST(port->uartclk, 16 * device->baud);
+ c = serial8250_early_in(port, UART_LCR);
+ serial8250_early_out(port, UART_LCR, c | UART_LCR_DLAB);
+ serial8250_early_out(port, UART_DLL, divisor & 0xff);
+ serial8250_early_out(port, UART_DLM, (divisor >> 8) & 0xff);
+ serial8250_early_out(port, UART_LCR, c & ~UART_LCR_DLAB);
+ }
}
int __init early_serial8250_setup(struct earlycon_device *device,