Merge branch 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6

* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
  serial: apbuart: Fixup apbuart_console_init()
  TTY: Add tty ioctl to figure device node of the system console.
  tty: add 'active' sysfs attribute to tty0 and console device
  drivers: serial: apbuart: Handle OF failures gracefully
  Serial: Avoid unbalanced IRQ wake disable during resume
  tty: fix typos/errors in tty_driver.h comments
  pch_uart : fix warnings for 64bit compile
  8250: fix uninitialized FIFOs
  ip2: fix compiler warning on ip2main_pci_tbl
  specialix: fix compiler warning on specialix_pci_tbl
  rocket: fix compiler warning on rocket_pci_ids
  8250: add a UPIO_DWAPB32 for 32 bit accesses
  8250: use container_of() instead of casting
  serial: omap-serial: Add support for kernel debugger
  serial: fix pch_uart kconfig & build
  drivers: char: hvc: add arm JTAG DCC console support
  RS485 documentation: add 16C950 UART description
  serial: ifx6x60: fix memory leak
  serial: ifx6x60: free IRQ on error
  Serial: EG20T: add PCH_UART driver
  ...

Fixed up conflicts in drivers/serial/apbuart.c with evil merge that
makes the code look fairly sane (unlike either side).

14 files changed, 3867 insertions, 78 deletions

diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index ee74c934de89..b25e6e490530 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -454,21 +454,40 @@ static void tsi_serial_out(struct uart_port *p, int offset, int value)
 		writeb(value, p->membase + offset);
 }
 
+/* Save the LCR value so it can be re-written when a Busy Detect IRQ occurs. */
+static inline void dwapb_save_out_value(struct uart_port *p, int offset,
+					int value)
+{
+	struct uart_8250_port *up =
+		container_of(p, struct uart_8250_port, port);
+
+	if (offset == UART_LCR)
+		up->lcr = value;
+}
+
+/* Read the IER to ensure any interrupt is cleared before returning from ISR. */
+static inline void dwapb_check_clear_ier(struct uart_port *p, int offset)
+{
+	if (offset == UART_TX || offset == UART_IER)
+		p->serial_in(p, UART_IER);
+}
+
 static void dwapb_serial_out(struct uart_port *p, int offset, int value)
 {
 	int save_offset = offset;
 	offset = map_8250_out_reg(p, offset) << p->regshift;
-	/* Save the LCR value so it can be re-written when a
-	 * Busy Detect interrupt occurs. */
-	if (save_offset == UART_LCR) {
-		struct uart_8250_port *up = (struct uart_8250_port *)p;
-		up->lcr = value;
-	}
+	dwapb_save_out_value(p, save_offset, value);
 	writeb(value, p->membase + offset);
-	/* Read the IER to ensure any interrupt is cleared before
-	 * returning from ISR. */
-	if (save_offset == UART_TX || save_offset == UART_IER)
-		value = p->serial_in(p, UART_IER);
+	dwapb_check_clear_ier(p, save_offset);
+}
+
+static void dwapb32_serial_out(struct uart_port *p, int offset, int value)
+{
+	int save_offset = offset;
+	offset = map_8250_out_reg(p, offset) << p->regshift;
+	dwapb_save_out_value(p, save_offset, value);
+	writel(value, p->membase + offset);
+	dwapb_check_clear_ier(p, save_offset);
 }
 
 static unsigned int io_serial_in(struct uart_port *p, int offset)
@@ -485,7 +504,8 @@ static void io_serial_out(struct uart_port *p, int offset, int value)
 
 static void set_io_from_upio(struct uart_port *p)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)p;
+	struct uart_8250_port *up =
+		container_of(p, struct uart_8250_port, port);
 	switch (p->iotype) {
 	case UPIO_HUB6:
 		p->serial_in = hub6_serial_in;
@@ -518,6 +538,11 @@ static void set_io_from_upio(struct uart_port *p)
 		p->serial_out = dwapb_serial_out;
 		break;
 
+	case UPIO_DWAPB32:
+		p->serial_in = mem32_serial_in;
+		p->serial_out = dwapb32_serial_out;
+		break;
+
 	default:
 		p->serial_in = io_serial_in;
 		p->serial_out = io_serial_out;
@@ -536,6 +561,7 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value)
 	case UPIO_MEM32:
 	case UPIO_AU:
 	case UPIO_DWAPB:
+	case UPIO_DWAPB32:
 		p->serial_out(p, offset, value);
 		p->serial_in(p, UART_LCR);	/* safe, no side-effects */
 		break;
@@ -1319,7 +1345,8 @@ static inline void __stop_tx(struct uart_8250_port *p)
 
 static void serial8250_stop_tx(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 
 	__stop_tx(up);
 
@@ -1336,7 +1363,8 @@ static void transmit_chars(struct uart_8250_port *up);
 
 static void serial8250_start_tx(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 
 	if (!(up->ier & UART_IER_THRI)) {
 		up->ier |= UART_IER_THRI;
@@ -1364,7 +1392,8 @@ static void serial8250_start_tx(struct uart_port *port)
 
 static void serial8250_stop_rx(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 
 	up->ier &= ~UART_IER_RLSI;
 	up->port.read_status_mask &= ~UART_LSR_DR;
@@ -1373,7 +1402,8 @@ static void serial8250_stop_rx(struct uart_port *port)
 
 static void serial8250_enable_ms(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 
 	/* no MSR capabilities */
 	if (up->bugs & UART_BUG_NOMSR)
@@ -1581,7 +1611,8 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id)
 			handled = 1;
 
 			end = NULL;
-		} else if (up->port.iotype == UPIO_DWAPB &&
+		} else if ((up->port.iotype == UPIO_DWAPB ||
+			    up->port.iotype == UPIO_DWAPB32) &&
 			  (iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
 			/* The DesignWare APB UART has an Busy Detect (0x07)
 			 * interrupt meaning an LCR write attempt occured while the
@@ -1781,7 +1812,8 @@ static void serial8250_backup_timeout(unsigned long data)
 
 static unsigned int serial8250_tx_empty(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned long flags;
 	unsigned int lsr;
 
@@ -1795,7 +1827,8 @@ static unsigned int serial8250_tx_empty(struct uart_port *port)
 
 static unsigned int serial8250_get_mctrl(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned int status;
 	unsigned int ret;
 
@@ -1815,7 +1848,8 @@ static unsigned int serial8250_get_mctrl(struct uart_port *port)
 
 static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned char mcr = 0;
 
 	if (mctrl & TIOCM_RTS)
@@ -1836,7 +1870,8 @@ static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
 
 static void serial8250_break_ctl(struct uart_port *port, int break_state)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned long flags;
 
 	spin_lock_irqsave(&up->port.lock, flags);
@@ -1890,7 +1925,8 @@ static void wait_for_xmitr(struct uart_8250_port *up, int bits)
 
 static int serial8250_get_poll_char(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned char lsr = serial_inp(up, UART_LSR);
 
 	if (!(lsr & UART_LSR_DR))
@@ -1904,7 +1940,8 @@ static void serial8250_put_poll_char(struct uart_port *port,
 			 unsigned char c)
 {
 	unsigned int ier;
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 
 	/*
 	 *	First save the IER then disable the interrupts
@@ -1938,11 +1975,14 @@ static void serial8250_put_poll_char(struct uart_port *port,
 
 static int serial8250_startup(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned long flags;
 	unsigned char lsr, iir;
 	int retval;
 
+	up->port.fifosize = uart_config[up->port.type].fifo_size;
+	up->tx_loadsz = uart_config[up->port.type].tx_loadsz;
 	up->capabilities = uart_config[up->port.type].flags;
 	up->mcr = 0;
 
@@ -2166,7 +2206,8 @@ dont_test_tx_en:
 
 static void serial8250_shutdown(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned long flags;
 
 	/*
@@ -2235,7 +2276,8 @@ void
 serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
 		          struct ktermios *old)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	unsigned char cval, fcr = 0;
 	unsigned long flags;
 	unsigned int baud, quot;
@@ -2435,7 +2477,8 @@ serial8250_set_ldisc(struct uart_port *port, int new)
 void serial8250_do_pm(struct uart_port *port, unsigned int state,
 		      unsigned int oldstate)
 {
-	struct uart_8250_port *p = (struct uart_8250_port *)port;
+	struct uart_8250_port *p =
+		container_of(port, struct uart_8250_port, port);
 
 	serial8250_set_sleep(p, state != 0);
 }
@@ -2476,6 +2519,7 @@ static int serial8250_request_std_resource(struct uart_8250_port *up)
 	case UPIO_MEM32:
 	case UPIO_MEM:
 	case UPIO_DWAPB:
+	case UPIO_DWAPB32:
 		if (!up->port.mapbase)
 			break;
 
@@ -2513,6 +2557,7 @@ static void serial8250_release_std_resource(struct uart_8250_port *up)
 	case UPIO_MEM32:
 	case UPIO_MEM:
 	case UPIO_DWAPB:
+	case UPIO_DWAPB32:
 		if (!up->port.mapbase)
 			break;
 
@@ -2566,7 +2611,8 @@ static void serial8250_release_rsa_resource(struct uart_8250_port *up)
 
 static void serial8250_release_port(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 
 	serial8250_release_std_resource(up);
 	if (up->port.type == PORT_RSA)
@@ -2575,7 +2621,8 @@ static void serial8250_release_port(struct uart_port *port)
 
 static int serial8250_request_port(struct uart_port *port)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	int ret = 0;
 
 	ret = serial8250_request_std_resource(up);
@@ -2590,7 +2637,8 @@ static int serial8250_request_port(struct uart_port *port)
 
 static void serial8250_config_port(struct uart_port *port, int flags)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 	int probeflags = PROBE_ANY;
 	int ret;
 
@@ -2771,7 +2819,8 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev)
 
 static void serial8250_console_putchar(struct uart_port *port, int ch)
 {
-	struct uart_8250_port *up = (struct uart_8250_port *)port;
+	struct uart_8250_port *up =
+		container_of(port, struct uart_8250_port, port);
 
 	wait_for_xmitr(up, UART_LSR_THRE);
 	serial_out(up, UART_TX, ch);
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index 842e3b2a02b1..8b8930f700b5 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -957,6 +957,22 @@ pci_default_setup(struct serial_private *priv,
 	return setup_port(priv, port, bar, offset, board->reg_shift);
 }
 
+static int
+ce4100_serial_setup(struct serial_private *priv,
+		  const struct pciserial_board *board,
+		  struct uart_port *port, int idx)
+{
+	int ret;
+
+	ret = setup_port(priv, port, 0, 0, board->reg_shift);
+	port->iotype = UPIO_MEM32;
+	port->type = PORT_XSCALE;
+	port->flags = (port->flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
+	port->regshift = 2;
+
+	return ret;
+}
+
 static int skip_tx_en_setup(struct serial_private *priv,
 			const struct pciserial_board *board,
 			struct uart_port *port, int idx)
@@ -981,6 +997,7 @@ static int skip_tx_en_setup(struct serial_private *priv,
 #define PCI_SUBDEVICE_ID_POCTAL232	0x0308
 #define PCI_SUBDEVICE_ID_POCTAL422	0x0408
 #define PCI_VENDOR_ID_ADVANTECH		0x13fe
+#define PCI_DEVICE_ID_INTEL_CE4100_UART 0x2e66
 #define PCI_DEVICE_ID_ADVANTECH_PCI3620	0x3620
 #define PCI_DEVICE_ID_TITAN_200I	0x8028
 #define PCI_DEVICE_ID_TITAN_400I	0x8048
@@ -1072,6 +1089,13 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.subdevice	= PCI_ANY_ID,
 		.setup		= skip_tx_en_setup,
 	},
+	{
+		.vendor		= PCI_VENDOR_ID_INTEL,
+		.device		= PCI_DEVICE_ID_INTEL_CE4100_UART,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= ce4100_serial_setup,
+	},
 	/*
 	 * ITE
 	 */
@@ -1592,6 +1616,7 @@ enum pci_board_num_t {
 	pbn_ADDIDATA_PCIe_2_3906250,
 	pbn_ADDIDATA_PCIe_4_3906250,
 	pbn_ADDIDATA_PCIe_8_3906250,
+	pbn_ce4100_1_115200,
 };
 
 /*
@@ -2281,6 +2306,12 @@ static struct pciserial_board pci_boards[] __devinitdata = {
 		.uart_offset	= 0x200,
 		.first_offset	= 0x1000,
 	},
+	[pbn_ce4100_1_115200] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 1,
+		.base_baud	= 921600,
+		.reg_shift      = 2,
+	},
 };
 
 static const struct pci_device_id softmodem_blacklist[] = {
@@ -3765,6 +3796,11 @@ static struct pci_device_id serial_pci_tbl[] = {
 	{	PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
 		0xA000, 0x3004,
 		0, 0, pbn_b0_bt_4_115200 },
+	/* Intel CE4100 */
+	{	PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_CE4100_UART,
+		PCI_ANY_ID,  PCI_ANY_ID, 0, 0,
+		pbn_ce4100_1_115200 },
+
 
 	/*
 	 * These entries match devices with class COMMUNICATION_SERIAL,
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index aff9dcd051c6..ec3c214598d0 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -1381,6 +1381,16 @@ config SERIAL_MSM_CONSOLE
 	depends on SERIAL_MSM=y
 	select SERIAL_CORE_CONSOLE
 
+config SERIAL_VT8500
+	bool "VIA VT8500 on-chip serial port support"
+	depends on ARM && ARCH_VT8500
+	select SERIAL_CORE
+
+config SERIAL_VT8500_CONSOLE
+	bool "VIA VT8500 serial console support"
+	depends on SERIAL_VT8500=y
+	select SERIAL_CORE_CONSOLE
+
 config SERIAL_NETX
 	tristate "NetX serial port support"
 	depends on ARM && ARCH_NETX
@@ -1632,4 +1642,19 @@ config SERIAL_ALTERA_UART_CONSOLE
 	help
 	  Enable a Altera UART port to be the system console.
 
+config SERIAL_IFX6X60
+        tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)"
+	depends on GPIOLIB && SPI && EXPERIMENTAL
+	help
+	  Support for the IFX6x60 modem devices on Intel MID platforms.
+
+config SERIAL_PCH_UART
+	tristate "Intel EG20T PCH UART"
+	depends on PCI && DMADEVICES
+	select SERIAL_CORE
+	select PCH_DMA
+	help
+	  This driver is for PCH(Platform controller Hub) UART of Intel EG20T
+	  which is an IOH(Input/Output Hub) for x86 embedded processor.
+	  Enabling PCH_DMA, this PCH UART works as DMA mode.
 endmenu
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index c5705765454f..8ea92e9c73b0 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -80,12 +80,15 @@ obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o
 obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
+obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
 obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
 obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
 obj-$(CONFIG_SERIAL_TIMBERDALE)	+= timbuart.o
 obj-$(CONFIG_SERIAL_GRLIB_GAISLER_APBUART) += apbuart.o
 obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o
 obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
+obj-$(CONFIG_SERIAL_VT8500) += vt8500_serial.o
 obj-$(CONFIG_SERIAL_MRST_MAX3110)	+= mrst_max3110.o
 obj-$(CONFIG_SERIAL_MFD_HSU)	+= mfd.o
-obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
+obj-$(CONFIG_SERIAL_IFX6X60)  	+= ifx6x60.o
+obj-$(CONFIG_SERIAL_PCH_UART)	+= pch_uart.o
diff --git a/drivers/serial/apbuart.c b/drivers/serial/apbuart.c
index 767ce9e396c5..095a5d562618 100644
--- a/drivers/serial/apbuart.c
+++ b/drivers/serial/apbuart.c
@@ -521,11 +521,12 @@ static struct console grlib_apbuart_console = {
 };
 
 
-static void grlib_apbuart_configure(void);
+static int grlib_apbuart_configure(void);
 
 static int __init apbuart_console_init(void)
 {
-	grlib_apbuart_configure();
+	if (grlib_apbuart_configure())
+		return -ENODEV;
 	register_console(&grlib_apbuart_console);
 	return 0;
 }
@@ -596,57 +597,49 @@ static struct of_platform_driver grlib_apbuart_of_driver = {
 };
 
 
-static void grlib_apbuart_configure(void)
+static int grlib_apbuart_configure(void)
 {
-	static int enum_done;
 	struct device_node *np, *rp;
-	struct uart_port *port = NULL;
 	const u32 *prop;
-	int freq_khz;
-	int v = 0, d = 0;
-	unsigned int addr;
-	int irq, line;
-	struct amba_prom_registers *regs;
-
-	if (enum_done)
-		return;
+	int freq_khz, line = 0;
 
 	/* Get bus frequency */
 	rp = of_find_node_by_path("/");
+	if (!rp)
+		return -ENODEV;
 	rp = of_get_next_child(rp, NULL);
+	if (!rp)
+		return -ENODEV;
 	prop = of_get_property(rp, "clock-frequency", NULL);
+	if (!prop)
+		return -ENODEV;
 	freq_khz = *prop;
 
-	line = 0;
 	for_each_matching_node(np, apbuart_match) {
+		const int *irqs, *ampopts;
+		const struct amba_prom_registers *regs;
+		struct uart_port *port;
+		unsigned long addr;
 
-		int *vendor = (int *) of_get_property(np, "vendor", NULL);
-		int *device = (int *) of_get_property(np, "device", NULL);
-		int *irqs = (int *) of_get_property(np, "interrupts", NULL);
-		int *ampopts = (int *) of_get_property(np, "ampopts", NULL);
-		regs = (struct amba_prom_registers *)
-		    of_get_property(np, "reg", NULL);
-
+		ampopts = of_get_property(np, "ampopts", NULL);
 		if (ampopts && (*ampopts == 0))
 			continue; /* Ignore if used by another OS instance */
-		if (vendor)
-			v = *vendor;
-		if (device)
-			d = *device;
+
+		irqs = of_get_property(np, "interrupts", NULL);
+		regs = of_get_property(np, "reg", NULL);
 
 		if (!irqs || !regs)
-			return;
+			continue;
 
 		grlib_apbuart_nodes[line] = np;
 
 		addr = regs->phys_addr;
-		irq = *irqs;
 
 		port = &grlib_apbuart_ports[line];
 
 		port->mapbase = addr;
 		port->membase = ioremap(addr, sizeof(struct grlib_apbuart_regs_map));
-		port->irq = irq;
+		port->irq = *irqs;
 		port->iotype = UPIO_MEM;
 		port->ops = &grlib_apbuart_ops;
 		port->flags = UPF_BOOT_AUTOCONF;
@@ -658,12 +651,10 @@ static void grlib_apbuart_configure(void)
 		/* We support maximum UART_NR uarts ... */
 		if (line == UART_NR)
 			break;
-
 	}
 
-	enum_done = 1;
-
 	grlib_apbuart_driver.nr = grlib_apbuart_port_nr = line;
+	return line ? 0 : -ENODEV;
 }
 
 static int __init grlib_apbuart_init(void)
@@ -671,7 +662,9 @@ static int __init grlib_apbuart_init(void)
 	int ret;
 
 	/* Find all APBUARTS in device the tree and initialize their ports */
-	grlib_apbuart_configure();
+	ret = grlib_apbuart_configure();
+	if (ret)
+		return ret;
 
 	printk(KERN_INFO "Serial: GRLIB APBUART driver\n");
 
diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h
index 7274b527a3c1..b754dcf0fda5 100644
--- a/drivers/serial/cpm_uart/cpm_uart.h
+++ b/drivers/serial/cpm_uart/cpm_uart.h
@@ -76,18 +76,12 @@ struct uart_cpm_port {
 	unsigned char		*tx_buf;
 	unsigned char		*rx_buf;
 	u32			flags;
-	void			(*set_lineif)(struct uart_cpm_port *);
 	struct clk		*clk;
 	u8			brg;
 	uint			 dp_addr;
 	void			*mem_addr;
 	dma_addr_t		 dma_addr;
 	u32			mem_size;
-	/* helpers */
-	int			 baud;
-	int			 bits;
-	/* Keep track of 'odd' SMC2 wirings */
-	int			is_portb;
 	/* wait on close if needed */
 	int			wait_closing;
 	/* value to combine with opcode to form cpm command */
diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index f2b8adcc6c92..8692ff98fc07 100644
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -72,6 +72,8 @@ static void cpm_uart_initbd(struct uart_cpm_port *pinfo);
 
 /**************************************************************/
 
+#define HW_BUF_SPD_THRESHOLD    9600
+
 /*
  * Check, if transmit buffers are processed
 */
@@ -503,6 +505,11 @@ static void cpm_uart_set_termios(struct uart_port *port,
 	pr_debug("CPM uart[%d]:set_termios\n", port->line);
 
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
+	if (baud <= HW_BUF_SPD_THRESHOLD ||
+	    (pinfo->port.state && pinfo->port.state->port.tty->low_latency))
+		pinfo->rx_fifosize = 1;
+	else
+		pinfo->rx_fifosize = RX_BUF_SIZE;
 
 	/* Character length programmed into the mode register is the
 	 * sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
@@ -594,6 +601,17 @@ static void cpm_uart_set_termios(struct uart_port *port,
 	 */
 	bits++;
 	if (IS_SMC(pinfo)) {
+		/*
+		 * MRBLR can be changed while an SMC/SCC is operating only
+		 * if it is done in a single bus cycle with one 16-bit move
+		 * (not two 8-bit bus cycles back-to-back). This occurs when
+		 * the cp shifts control to the next RxBD, so the change does
+		 * not take effect immediately. To guarantee the exact RxBD
+		 * on which the change occurs, change MRBLR only while the
+		 * SMC/SCC receiver is disabled.
+		 */
+		out_be16(&pinfo->smcup->smc_mrblr, pinfo->rx_fifosize);
+
 		/* Set the mode register.  We want to keep a copy of the
 		 * enables, because we want to put them back if they were
 		 * present.
@@ -604,6 +622,7 @@ static void cpm_uart_set_termios(struct uart_port *port,
 		out_be16(&smcp->smc_smcmr, smcr_mk_clen(bits) | cval |
 		    SMCMR_SM_UART | prev_mode);
 	} else {
+		out_be16(&pinfo->sccup->scc_genscc.scc_mrblr, pinfo->rx_fifosize);
 		out_be16(&sccp->scc_psmr, (sbits << 12) | scval);
 	}
 
diff --git a/drivers/serial/ifx6x60.c b/drivers/serial/ifx6x60.c
new file mode 100644
index 000000000000..ab93763862d5
--- /dev/null
+++ b/drivers/serial/ifx6x60.c
@@ -0,0 +1,1406 @@
+/****************************************************************************
+ *
+ * Driver for the IFX 6x60 spi modem.
+ *
+ * Copyright (C) 2008 Option International
+ * Copyright (C) 2008 Filip Aben <f.aben@option.com>
+ *		      Denis Joseph Barrow <d.barow@option.com>
+ *		      Jan Dumon <j.dumon@option.com>
+ *
+ * Copyright (C) 2009, 2010 Intel Corp
+ * Russ Gorby <richardx.r.gorby@intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301,
+ * USA
+ *
+ * Driver modified by Intel from Option gtm501l_spi.c
+ *
+ * Notes
+ * o	The driver currently assumes a single device only. If you need to
+ *	change this then look for saved_ifx_dev and add a device lookup
+ * o	The driver is intended to be big-endian safe but has never been
+ *	tested that way (no suitable hardware). There are a couple of FIXME
+ *	notes by areas that may need addressing
+ * o	Some of the GPIO naming/setup assumptions may need revisiting if
+ *	you need to use this driver for another platform.
+ *
+ *****************************************************************************/
+#include <linux/module.h>
+#include <linux/termios.h>
+#include <linux/tty.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+#include <linux/tty.h>
+#include <linux/kfifo.h>
+#include <linux/tty_flip.h>
+#include <linux/timer.h>
+#include <linux/serial.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/rfkill.h>
+#include <linux/fs.h>
+#include <linux/ip.h>
+#include <linux/dmapool.h>
+#include <linux/gpio.h>
+#include <linux/sched.h>
+#include <linux/time.h>
+#include <linux/wait.h>
+#include <linux/tty.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
+#include <linux/spi/ifx_modem.h>
+#include <linux/delay.h>
+
+#include "ifx6x60.h"
+
+#define IFX_SPI_MORE_MASK		0x10
+#define IFX_SPI_MORE_BIT		12	/* bit position in u16 */
+#define IFX_SPI_CTS_BIT			13	/* bit position in u16 */
+#define IFX_SPI_TTY_ID			0
+#define IFX_SPI_TIMEOUT_SEC		2
+#define IFX_SPI_HEADER_0		(-1)
+#define IFX_SPI_HEADER_F		(-2)
+
+/* forward reference */
+static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev);
+
+/* local variables */
+static int spi_b16 = 1;			/* 8 or 16 bit word length */
+static struct tty_driver *tty_drv;
+static struct ifx_spi_device *saved_ifx_dev;
+static struct lock_class_key ifx_spi_key;
+
+/* GPIO/GPE settings */
+
+/**
+ *	mrdy_set_high		-	set MRDY GPIO
+ *	@ifx: device we are controlling
+ *
+ */
+static inline void mrdy_set_high(struct ifx_spi_device *ifx)
+{
+	gpio_set_value(ifx->gpio.mrdy, 1);
+}
+
+/**
+ *	mrdy_set_low		-	clear MRDY GPIO
+ *	@ifx: device we are controlling
+ *
+ */
+static inline void mrdy_set_low(struct ifx_spi_device *ifx)
+{
+	gpio_set_value(ifx->gpio.mrdy, 0);
+}
+
+/**
+ *	ifx_spi_power_state_set
+ *	@ifx_dev: our SPI device
+ *	@val: bits to set
+ *
+ *	Set bit in power status and signal power system if status becomes non-0
+ */
+static void
+ifx_spi_power_state_set(struct ifx_spi_device *ifx_dev, unsigned char val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ifx_dev->power_lock, flags);
+
+	/*
+	 * if power status is already non-0, just update, else
+	 * tell power system
+	 */
+	if (!ifx_dev->power_status)
+		pm_runtime_get(&ifx_dev->spi_dev->dev);
+	ifx_dev->power_status |= val;
+
+	spin_unlock_irqrestore(&ifx_dev->power_lock, flags);
+}
+
+/**
+ *	ifx_spi_power_state_clear	-	clear power bit
+ *	@ifx_dev: our SPI device
+ *	@val: bits to clear
+ *
+ *	clear bit in power status and signal power system if status becomes 0
+ */
+static void
+ifx_spi_power_state_clear(struct ifx_spi_device *ifx_dev, unsigned char val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ifx_dev->power_lock, flags);
+
+	if (ifx_dev->power_status) {
+		ifx_dev->power_status &= ~val;
+		if (!ifx_dev->power_status)
+			pm_runtime_put(&ifx_dev->spi_dev->dev);
+	}
+
+	spin_unlock_irqrestore(&ifx_dev->power_lock, flags);
+}
+
+/**
+ *	swap_buf
+ *	@buf: our buffer
+ *	@len : number of bytes (not words) in the buffer
+ *	@end: end of buffer
+ *
+ *	Swap the contents of a buffer into big endian format
+ */
+static inline void swap_buf(u16 *buf, int len, void *end)
+{
+	int n;
+
+	len = ((len + 1) >> 1);
+	if ((void *)&buf[len] > end) {
+		pr_err("swap_buf: swap exceeds boundary (%p > %p)!",
+		       &buf[len], end);
+		return;
+	}
+	for (n = 0; n < len; n++) {
+		*buf = cpu_to_be16(*buf);
+		buf++;
+	}
+}
+
+/**
+ *	mrdy_assert		-	assert MRDY line
+ *	@ifx_dev: our SPI device
+ *
+ *	Assert mrdy and set timer to wait for SRDY interrupt, if SRDY is low
+ *	now.
+ *
+ *	FIXME: Can SRDY even go high as we are running this code ?
+ */
+static void mrdy_assert(struct ifx_spi_device *ifx_dev)
+{
+	int val = gpio_get_value(ifx_dev->gpio.srdy);
+	if (!val) {
+		if (!test_and_set_bit(IFX_SPI_STATE_TIMER_PENDING,
+				      &ifx_dev->flags)) {
+			ifx_dev->spi_timer.expires =
+				jiffies + IFX_SPI_TIMEOUT_SEC*HZ;
+			add_timer(&ifx_dev->spi_timer);
+
+		}
+	}
+	ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_DATA_PENDING);
+	mrdy_set_high(ifx_dev);
+}
+
+/**
+ *	ifx_spi_hangup		-	hang up an IFX device
+ *	@ifx_dev: our SPI device
+ *
+ *	Hang up the tty attached to the IFX device if one is currently
+ *	open. If not take no action
+ */
+static void ifx_spi_ttyhangup(struct ifx_spi_device *ifx_dev)
+{
+	struct tty_port *pport = &ifx_dev->tty_port;
+	struct tty_struct *tty = tty_port_tty_get(pport);
+	if (tty) {
+		tty_hangup(tty);
+		tty_kref_put(tty);
+	}
+}
+
+/**
+ *	ifx_spi_timeout		-	SPI timeout
+ *	@arg: our SPI device
+ *
+ *	The SPI has timed out: hang up the tty. Users will then see a hangup
+ *	and error events.
+ */
+static void ifx_spi_timeout(unsigned long arg)
+{
+	struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *)arg;
+
+	dev_warn(&ifx_dev->spi_dev->dev, "*** SPI Timeout ***");
+	ifx_spi_ttyhangup(ifx_dev);
+	mrdy_set_low(ifx_dev);
+	clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
+}
+
+/* char/tty operations */
+
+/**
+ *	ifx_spi_tiocmget	-	get modem lines
+ *	@tty: our tty device
+ *	@filp: file handle issuing the request
+ *
+ *	Map the signal state into Linux modem flags and report the value
+ *	in Linux terms
+ */
+static int ifx_spi_tiocmget(struct tty_struct *tty, struct file *filp)
+{
+	unsigned int value;
+	struct ifx_spi_device *ifx_dev = tty->driver_data;
+
+	value =
+	(test_bit(IFX_SPI_RTS, &ifx_dev->signal_state) ? TIOCM_RTS : 0) |
+	(test_bit(IFX_SPI_DTR, &ifx_dev->signal_state) ? TIOCM_DTR : 0) |
+	(test_bit(IFX_SPI_CTS, &ifx_dev->signal_state) ? TIOCM_CTS : 0) |
+	(test_bit(IFX_SPI_DSR, &ifx_dev->signal_state) ? TIOCM_DSR : 0) |
+	(test_bit(IFX_SPI_DCD, &ifx_dev->signal_state) ? TIOCM_CAR : 0) |
+	(test_bit(IFX_SPI_RI, &ifx_dev->signal_state) ? TIOCM_RNG : 0);
+	return value;
+}
+
+/**
+ *	ifx_spi_tiocmset	-	set modem bits
+ *	@tty: the tty structure
+ *	@filp: file handle issuing the request
+ *	@set: bits to set
+ *	@clear: bits to clear
+ *
+ *	The IFX6x60 only supports DTR and RTS. Set them accordingly
+ *	and flag that an update to the modem is needed.
+ *
+ *	FIXME: do we need to kick the tranfers when we do this ?
+ */
+static int ifx_spi_tiocmset(struct tty_struct *tty, struct file *filp,
+			    unsigned int set, unsigned int clear)
+{
+	struct ifx_spi_device *ifx_dev = tty->driver_data;
+
+	if (set & TIOCM_RTS)
+		set_bit(IFX_SPI_RTS, &ifx_dev->signal_state);
+	if (set & TIOCM_DTR)
+		set_bit(IFX_SPI_DTR, &ifx_dev->signal_state);
+	if (clear & TIOCM_RTS)
+		clear_bit(IFX_SPI_RTS, &ifx_dev->signal_state);
+	if (clear & TIOCM_DTR)
+		clear_bit(IFX_SPI_DTR, &ifx_dev->signal_state);
+
+	set_bit(IFX_SPI_UPDATE, &ifx_dev->signal_state);
+	return 0;
+}
+
+/**
+ *	ifx_spi_open	-	called on tty open
+ *	@tty: our tty device
+ *	@filp: file handle being associated with the tty
+ *
+ *	Open the tty interface. We let the tty_port layer do all the work
+ *	for us.
+ *
+ *	FIXME: Remove single device assumption and saved_ifx_dev
+ */
+static int ifx_spi_open(struct tty_struct *tty, struct file *filp)
+{
+	return tty_port_open(&saved_ifx_dev->tty_port, tty, filp);
+}
+
+/**
+ *	ifx_spi_close	-	called when our tty closes
+ *	@tty: the tty being closed
+ *	@filp: the file handle being closed
+ *
+ *	Perform the close of the tty. We use the tty_port layer to do all
+ *	our hard work.
+ */
+static void ifx_spi_close(struct tty_struct *tty, struct file *filp)
+{
+	struct ifx_spi_device *ifx_dev = tty->driver_data;
+	tty_port_close(&ifx_dev->tty_port, tty, filp);
+	/* FIXME: should we do an ifx_spi_reset here ? */
+}
+
+/**
+ *	ifx_decode_spi_header	-	decode received header
+ *	@buffer: the received data
+ *	@length: decoded length
+ *	@more: decoded more flag
+ *	@received_cts: status of cts we received
+ *
+ *	Note how received_cts is handled -- if header is all F it is left
+ *	the same as it was, if header is all 0 it is set to 0 otherwise it is
+ *	taken from the incoming header.
+ *
+ *	FIXME: endianness
+ */
+static int ifx_spi_decode_spi_header(unsigned char *buffer, int *length,
+			unsigned char *more, unsigned char *received_cts)
+{
+	u16 h1;
+	u16 h2;
+	u16 *in_buffer = (u16 *)buffer;
+
+	h1 = *in_buffer;
+	h2 = *(in_buffer+1);
+
+	if (h1 == 0 && h2 == 0) {
+		*received_cts = 0;
+		return IFX_SPI_HEADER_0;
+	} else if (h1 == 0xffff && h2 == 0xffff) {
+		/* spi_slave_cts remains as it was */
+		return IFX_SPI_HEADER_F;
+	}
+
+	*length = h1 & 0xfff;	/* upper bits of byte are flags */
+	*more = (buffer[1] >> IFX_SPI_MORE_BIT) & 1;
+	*received_cts = (buffer[3] >> IFX_SPI_CTS_BIT) & 1;
+	return 0;
+}
+
+/**
+ *	ifx_setup_spi_header	-	set header fields
+ *	@txbuffer: pointer to start of SPI buffer
+ *	@tx_count: bytes
+ *	@more: indicate if more to follow
+ *
+ *	Format up an SPI header for a transfer
+ *
+ *	FIXME: endianness?
+ */
+static void ifx_spi_setup_spi_header(unsigned char *txbuffer, int tx_count,
+					unsigned char more)
+{
+	*(u16 *)(txbuffer) = tx_count;
+	*(u16 *)(txbuffer+2) = IFX_SPI_PAYLOAD_SIZE;
+	txbuffer[1] |= (more << IFX_SPI_MORE_BIT) & IFX_SPI_MORE_MASK;
+}
+
+/**
+ *	ifx_spi_wakeup_serial	-	SPI space made
+ *	@port_data: our SPI device
+ *
+ *	We have emptied the FIFO enough that we want to get more data
+ *	queued into it. Poke the line discipline via tty_wakeup so that
+ *	it will feed us more bits
+ */
+static void ifx_spi_wakeup_serial(struct ifx_spi_device *ifx_dev)
+{
+	struct tty_struct *tty;
+
+	tty = tty_port_tty_get(&ifx_dev->tty_port);
+	if (!tty)
+		return;
+	tty_wakeup(tty);
+	tty_kref_put(tty);
+}
+
+/**
+ *	ifx_spi_prepare_tx_buffer	-	prepare transmit frame
+ *	@ifx_dev: our SPI device
+ *
+ *	The transmit buffr needs a header and various other bits of
+ *	information followed by as much data as we can pull from the FIFO
+ *	and transfer. This function formats up a suitable buffer in the
+ *	ifx_dev->tx_buffer
+ *
+ *	FIXME: performance - should we wake the tty when the queue is half
+ *			     empty ?
+ */
+static int ifx_spi_prepare_tx_buffer(struct ifx_spi_device *ifx_dev)
+{
+	int temp_count;
+	int queue_length;
+	int tx_count;
+	unsigned char *tx_buffer;
+
+	tx_buffer = ifx_dev->tx_buffer;
+	memset(tx_buffer, 0, IFX_SPI_TRANSFER_SIZE);
+
+	/* make room for required SPI header */
+	tx_buffer += IFX_SPI_HEADER_OVERHEAD;
+	tx_count = IFX_SPI_HEADER_OVERHEAD;
+
+	/* clear to signal no more data if this turns out to be the
+	 * last buffer sent in a sequence */
+	ifx_dev->spi_more = 0;
+
+	/* if modem cts is set, just send empty buffer */
+	if (!ifx_dev->spi_slave_cts) {
+		/* see if there's tx data */
+		queue_length = kfifo_len(&ifx_dev->tx_fifo);
+		if (queue_length != 0) {
+			/* data to mux -- see if there's room for it */
+			temp_count = min(queue_length, IFX_SPI_PAYLOAD_SIZE);
+			temp_count = kfifo_out_locked(&ifx_dev->tx_fifo,
+					tx_buffer, temp_count,
+					&ifx_dev->fifo_lock);
+
+			/* update buffer pointer and data count in message */
+			tx_buffer += temp_count;
+			tx_count += temp_count;
+			if (temp_count == queue_length)
+				/* poke port to get more data */
+				ifx_spi_wakeup_serial(ifx_dev);
+			else /* more data in port, use next SPI message */
+				ifx_dev->spi_more = 1;
+		}
+	}
+	/* have data and info for header -- set up SPI header in buffer */
+	/* spi header needs payload size, not entire buffer size */
+	ifx_spi_setup_spi_header(ifx_dev->tx_buffer,
+					tx_count-IFX_SPI_HEADER_OVERHEAD,
+					ifx_dev->spi_more);
+	/* swap actual data in the buffer */
+	swap_buf((u16 *)(ifx_dev->tx_buffer), tx_count,
+		&ifx_dev->tx_buffer[IFX_SPI_TRANSFER_SIZE]);
+	return tx_count;
+}
+
+/**
+ *	ifx_spi_write		-	line discipline write
+ *	@tty: our tty device
+ *	@buf: pointer to buffer to write (kernel space)
+ *	@count: size of buffer
+ *
+ *	Write the characters we have been given into the FIFO. If the device
+ *	is not active then activate it, when the SRDY line is asserted back
+ *	this will commence I/O
+ */
+static int ifx_spi_write(struct tty_struct *tty, const unsigned char *buf,
+			 int count)
+{
+	struct ifx_spi_device *ifx_dev = tty->driver_data;
+	unsigned char *tmp_buf = (unsigned char *)buf;
+	int tx_count = kfifo_in_locked(&ifx_dev->tx_fifo, tmp_buf, count,
+				   &ifx_dev->fifo_lock);
+	mrdy_assert(ifx_dev);
+	return tx_count;
+}
+
+/**
+ *	ifx_spi_chars_in_buffer	-	line discipline helper
+ *	@tty: our tty device
+ *
+ *	Report how much data we can accept before we drop bytes. As we use
+ *	a simple FIFO this is nice and easy.
+ */
+static int ifx_spi_write_room(struct tty_struct *tty)
+{
+	struct ifx_spi_device *ifx_dev = tty->driver_data;
+	return IFX_SPI_FIFO_SIZE - kfifo_len(&ifx_dev->tx_fifo);
+}
+
+/**
+ *	ifx_spi_chars_in_buffer	-	line discipline helper
+ *	@tty: our tty device
+ *
+ *	Report how many characters we have buffered. In our case this is the
+ *	number of bytes sitting in our transmit FIFO.
+ */
+static int ifx_spi_chars_in_buffer(struct tty_struct *tty)
+{
+	struct ifx_spi_device *ifx_dev = tty->driver_data;
+	return kfifo_len(&ifx_dev->tx_fifo);
+}
+
+/**
+ *	ifx_port_hangup
+ *	@port: our tty port
+ *
+ *	tty port hang up. Called when tty_hangup processing is invoked either
+ *	by loss of carrier, or by software (eg vhangup). Serialized against
+ *	activate/shutdown by the tty layer.
+ */
+static void ifx_spi_hangup(struct tty_struct *tty)
+{
+	struct ifx_spi_device *ifx_dev = tty->driver_data;
+	tty_port_hangup(&ifx_dev->tty_port);
+}
+
+/**
+ *	ifx_port_activate
+ *	@port: our tty port
+ *
+ *	tty port activate method - called for first open. Serialized
+ *	with hangup and shutdown by the tty layer.
+ */
+static int ifx_port_activate(struct tty_port *port, struct tty_struct *tty)
+{
+	struct ifx_spi_device *ifx_dev =
+		container_of(port, struct ifx_spi_device, tty_port);
+
+	/* clear any old data; can't do this in 'close' */
+	kfifo_reset(&ifx_dev->tx_fifo);
+
+	/* put port data into this tty */
+	tty->driver_data = ifx_dev;
+
+	/* allows flip string push from int context */
+	tty->low_latency = 1;
+
+	return 0;
+}
+
+/**
+ *	ifx_port_shutdown
+ *	@port: our tty port
+ *
+ *	tty port shutdown method - called for last port close. Serialized
+ *	with hangup and activate by the tty layer.
+ */
+static void ifx_port_shutdown(struct tty_port *port)
+{
+	struct ifx_spi_device *ifx_dev =
+		container_of(port, struct ifx_spi_device, tty_port);
+
+	mrdy_set_low(ifx_dev);
+	clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
+	tasklet_kill(&ifx_dev->io_work_tasklet);
+}
+
+static const struct tty_port_operations ifx_tty_port_ops = {
+	.activate = ifx_port_activate,
+	.shutdown = ifx_port_shutdown,
+};
+
+static const struct tty_operations ifx_spi_serial_ops = {
+	.open = ifx_spi_open,
+	.close = ifx_spi_close,
+	.write = ifx_spi_write,
+	.hangup = ifx_spi_hangup,
+	.write_room = ifx_spi_write_room,
+	.chars_in_buffer = ifx_spi_chars_in_buffer,
+	.tiocmget = ifx_spi_tiocmget,
+	.tiocmset = ifx_spi_tiocmset,
+};
+
+/**
+ *	ifx_spi_insert_fip_string	-	queue received data
+ *	@ifx_ser: our SPI device
+ *	@chars: buffer we have received
+ *	@size: number of chars reeived
+ *
+ *	Queue bytes to the tty assuming the tty side is currently open. If
+ *	not the discard the data.
+ */
+static void ifx_spi_insert_flip_string(struct ifx_spi_device *ifx_dev,
+				    unsigned char *chars, size_t size)
+{
+	struct tty_struct *tty = tty_port_tty_get(&ifx_dev->tty_port);
+	if (!tty)
+		return;
+	tty_insert_flip_string(tty, chars, size);
+	tty_flip_buffer_push(tty);
+	tty_kref_put(tty);
+}
+
+/**
+ *	ifx_spi_complete	-	SPI transfer completed
+ *	@ctx: our SPI device
+ *
+ *	An SPI transfer has completed. Process any received data and kick off
+ *	any further transmits we can commence.
+ */
+static void ifx_spi_complete(void *ctx)
+{
+	struct ifx_spi_device *ifx_dev = ctx;
+	struct tty_struct *tty;
+	struct tty_ldisc *ldisc = NULL;
+	int length;
+	int actual_length;
+	unsigned char more;
+	unsigned char cts;
+	int local_write_pending = 0;
+	int queue_length;
+	int srdy;
+	int decode_result;
+
+	mrdy_set_low(ifx_dev);
+
+	if (!ifx_dev->spi_msg.status) {
+		/* check header validity, get comm flags */
+		swap_buf((u16 *)ifx_dev->rx_buffer, IFX_SPI_HEADER_OVERHEAD,
+			&ifx_dev->rx_buffer[IFX_SPI_HEADER_OVERHEAD]);
+		decode_result = ifx_spi_decode_spi_header(ifx_dev->rx_buffer,
+				&length, &more, &cts);
+		if (decode_result == IFX_SPI_HEADER_0) {
+			dev_dbg(&ifx_dev->spi_dev->dev,
+				"ignore input: invalid header 0");
+			ifx_dev->spi_slave_cts = 0;
+			goto complete_exit;
+		} else if (decode_result == IFX_SPI_HEADER_F) {
+			dev_dbg(&ifx_dev->spi_dev->dev,
+				"ignore input: invalid header F");
+			goto complete_exit;
+		}
+
+		ifx_dev->spi_slave_cts = cts;
+
+		actual_length = min((unsigned int)length,
+					ifx_dev->spi_msg.actual_length);
+		swap_buf((u16 *)(ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD),
+			 actual_length,
+			 &ifx_dev->rx_buffer[IFX_SPI_TRANSFER_SIZE]);
+		ifx_spi_insert_flip_string(
+			ifx_dev,
+			ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD,
+			(size_t)actual_length);
+	} else {
+		dev_dbg(&ifx_dev->spi_dev->dev, "SPI transfer error %d",
+		       ifx_dev->spi_msg.status);
+	}
+
+complete_exit:
+	if (ifx_dev->write_pending) {
+		ifx_dev->write_pending = 0;
+		local_write_pending = 1;
+	}
+
+	clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &(ifx_dev->flags));
+
+	queue_length = kfifo_len(&ifx_dev->tx_fifo);
+	srdy = gpio_get_value(ifx_dev->gpio.srdy);
+	if (!srdy)
+		ifx_spi_power_state_clear(ifx_dev, IFX_SPI_POWER_SRDY);
+
+	/* schedule output if there is more to do */
+	if (test_and_clear_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags))
+		tasklet_schedule(&ifx_dev->io_work_tasklet);
+	else {
+		if (more || ifx_dev->spi_more || queue_length > 0 ||
+			local_write_pending) {
+			if (ifx_dev->spi_slave_cts) {
+				if (more)
+					mrdy_assert(ifx_dev);
+			} else
+				mrdy_assert(ifx_dev);
+		} else {
+			/*
+			 * poke line discipline driver if any for more data
+			 * may or may not get more data to write
+			 * for now, say not busy
+			 */
+			ifx_spi_power_state_clear(ifx_dev,
+						  IFX_SPI_POWER_DATA_PENDING);
+			tty = tty_port_tty_get(&ifx_dev->tty_port);
+			if (tty) {
+				ldisc = tty_ldisc_ref(tty);
+				if (ldisc) {
+					ldisc->ops->write_wakeup(tty);
+					tty_ldisc_deref(ldisc);
+				}
+				tty_kref_put(tty);
+			}
+		}
+	}
+}
+
+/**
+ *	ifx_spio_io		-	I/O tasklet
+ *	@data: our SPI device
+ *
+ *	Queue data for transmission if possible and then kick off the
+ *	transfer.
+ */
+static void ifx_spi_io(unsigned long data)
+{
+	int retval;
+	struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *) data;
+
+	if (!test_and_set_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags)) {
+		if (ifx_dev->gpio.unack_srdy_int_nb > 0)
+			ifx_dev->gpio.unack_srdy_int_nb--;
+
+		ifx_spi_prepare_tx_buffer(ifx_dev);
+
+		spi_message_init(&ifx_dev->spi_msg);
+		INIT_LIST_HEAD(&ifx_dev->spi_msg.queue);
+
+		ifx_dev->spi_msg.context = ifx_dev;
+		ifx_dev->spi_msg.complete = ifx_spi_complete;
+
+		/* set up our spi transfer */
+		/* note len is BYTES, not transfers */
+		ifx_dev->spi_xfer.len = IFX_SPI_TRANSFER_SIZE;
+		ifx_dev->spi_xfer.cs_change = 0;
+		ifx_dev->spi_xfer.speed_hz = 12500000;
+		/* ifx_dev->spi_xfer.speed_hz = 390625; */
+		ifx_dev->spi_xfer.bits_per_word = spi_b16 ? 16 : 8;
+
+		ifx_dev->spi_xfer.tx_buf = ifx_dev->tx_buffer;
+		ifx_dev->spi_xfer.rx_buf = ifx_dev->rx_buffer;
+
+		/*
+		 * setup dma pointers
+		 */
+		if (ifx_dev->is_6160) {
+			ifx_dev->spi_msg.is_dma_mapped = 1;
+			ifx_dev->tx_dma = ifx_dev->tx_bus;
+			ifx_dev->rx_dma = ifx_dev->rx_bus;
+			ifx_dev->spi_xfer.tx_dma = ifx_dev->tx_dma;
+			ifx_dev->spi_xfer.rx_dma = ifx_dev->rx_dma;
+		} else {
+			ifx_dev->spi_msg.is_dma_mapped = 0;
+			ifx_dev->tx_dma = (dma_addr_t)0;
+			ifx_dev->rx_dma = (dma_addr_t)0;
+			ifx_dev->spi_xfer.tx_dma = (dma_addr_t)0;
+			ifx_dev->spi_xfer.rx_dma = (dma_addr_t)0;
+		}
+
+		spi_message_add_tail(&ifx_dev->spi_xfer, &ifx_dev->spi_msg);
+
+		/* Assert MRDY. This may have already been done by the write
+		 * routine.
+		 */
+		mrdy_assert(ifx_dev);
+
+		retval = spi_async(ifx_dev->spi_dev, &ifx_dev->spi_msg);
+		if (retval) {
+			clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS,
+				  &ifx_dev->flags);
+			tasklet_schedule(&ifx_dev->io_work_tasklet);
+			return;
+		}
+	} else
+		ifx_dev->write_pending = 1;
+}
+
+/**
+ *	ifx_spi_free_port	-	free up the tty side
+ *	@ifx_dev: IFX device going away
+ *
+ *	Unregister and free up a port when the device goes away
+ */
+static void ifx_spi_free_port(struct ifx_spi_device *ifx_dev)
+{
+	if (ifx_dev->tty_dev)
+		tty_unregister_device(tty_drv, ifx_dev->minor);
+	kfifo_free(&ifx_dev->tx_fifo);
+}
+
+/**
+ *	ifx_spi_create_port	-	create a new port
+ *	@ifx_dev: our spi device
+ *
+ *	Allocate and initialise the tty port that goes with this interface
+ *	and add it to the tty layer so that it can be opened.
+ */
+static int ifx_spi_create_port(struct ifx_spi_device *ifx_dev)
+{
+	int ret = 0;
+	struct tty_port *pport = &ifx_dev->tty_port;
+
+	spin_lock_init(&ifx_dev->fifo_lock);
+	lockdep_set_class_and_subclass(&ifx_dev->fifo_lock,
+		&ifx_spi_key, 0);
+
+	if (kfifo_alloc(&ifx_dev->tx_fifo, IFX_SPI_FIFO_SIZE, GFP_KERNEL)) {
+		ret = -ENOMEM;
+		goto error_ret;
+	}
+
+	pport->ops = &ifx_tty_port_ops;
+	tty_port_init(pport);
+	ifx_dev->minor = IFX_SPI_TTY_ID;
+	ifx_dev->tty_dev = tty_register_device(tty_drv, ifx_dev->minor,
+					       &ifx_dev->spi_dev->dev);
+	if (IS_ERR(ifx_dev->tty_dev)) {
+		dev_dbg(&ifx_dev->spi_dev->dev,
+			"%s: registering tty device failed", __func__);
+		ret = PTR_ERR(ifx_dev->tty_dev);
+		goto error_ret;
+	}
+	return 0;
+
+error_ret:
+	ifx_spi_free_port(ifx_dev);
+	return ret;
+}
+
+/**
+ *	ifx_spi_handle_srdy		-	handle SRDY
+ *	@ifx_dev: device asserting SRDY
+ *
+ *	Check our device state and see what we need to kick off when SRDY
+ *	is asserted. This usually means killing the timer and firing off the
+ *	I/O processing.
+ */
+static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev)
+{
+	if (test_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags)) {
+		del_timer_sync(&ifx_dev->spi_timer);
+		clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
+	}
+
+	ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_SRDY);
+
+	if (!test_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags))
+		tasklet_schedule(&ifx_dev->io_work_tasklet);
+	else
+		set_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags);
+}
+
+/**
+ *	ifx_spi_srdy_interrupt	-	SRDY asserted
+ *	@irq: our IRQ number
+ *	@dev: our ifx device
+ *
+ *	The modem asserted SRDY. Handle the srdy event
+ */
+static irqreturn_t ifx_spi_srdy_interrupt(int irq, void *dev)
+{
+	struct ifx_spi_device *ifx_dev = dev;
+	ifx_dev->gpio.unack_srdy_int_nb++;
+	ifx_spi_handle_srdy(ifx_dev);
+	return IRQ_HANDLED;
+}
+
+/**
+ *	ifx_spi_reset_interrupt	-	Modem has changed reset state
+ *	@irq: interrupt number
+ *	@dev: our device pointer
+ *
+ *	The modem has either entered or left reset state. Check the GPIO
+ *	line to see which.
+ *
+ *	FIXME: review locking on MR_INPROGRESS versus
+ *	parallel unsolicited reset/solicited reset
+ */
+static irqreturn_t ifx_spi_reset_interrupt(int irq, void *dev)
+{
+	struct ifx_spi_device *ifx_dev = dev;
+	int val = gpio_get_value(ifx_dev->gpio.reset_out);
+	int solreset = test_bit(MR_START, &ifx_dev->mdm_reset_state);
+
+	if (val == 0) {
+		/* entered reset */
+		set_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state);
+		if (!solreset) {
+			/* unsolicited reset  */
+			ifx_spi_ttyhangup(ifx_dev);
+		}
+	} else {
+		/* exited reset */
+		clear_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state);
+		if (solreset) {
+			set_bit(MR_COMPLETE, &ifx_dev->mdm_reset_state);
+			wake_up(&ifx_dev->mdm_reset_wait);
+		}
+	}
+	return IRQ_HANDLED;
+}
+
+/**
+ *	ifx_spi_free_device - free device
+ *	@ifx_dev: device to free
+ *
+ *	Free the IFX device
+ */
+static void ifx_spi_free_device(struct ifx_spi_device *ifx_dev)
+{
+	ifx_spi_free_port(ifx_dev);
+	dma_free_coherent(&ifx_dev->spi_dev->dev,
+				IFX_SPI_TRANSFER_SIZE,
+				ifx_dev->tx_buffer,
+				ifx_dev->tx_bus);
+	dma_free_coherent(&ifx_dev->spi_dev->dev,
+				IFX_SPI_TRANSFER_SIZE,
+				ifx_dev->rx_buffer,
+				ifx_dev->rx_bus);
+}
+
+/**
+ *	ifx_spi_reset	-	reset modem
+ *	@ifx_dev: modem to reset
+ *
+ *	Perform a reset on the modem
+ */
+static int ifx_spi_reset(struct ifx_spi_device *ifx_dev)
+{
+	int ret;
+	/*
+	 * set up modem power, reset
+	 *
+	 * delays are required on some platforms for the modem
+	 * to reset properly
+	 */
+	set_bit(MR_START, &ifx_dev->mdm_reset_state);
+	gpio_set_value(ifx_dev->gpio.po, 0);
+	gpio_set_value(ifx_dev->gpio.reset, 0);
+	msleep(25);
+	gpio_set_value(ifx_dev->gpio.reset, 1);
+	msleep(1);
+	gpio_set_value(ifx_dev->gpio.po, 1);
+	msleep(1);
+	gpio_set_value(ifx_dev->gpio.po, 0);
+	ret = wait_event_timeout(ifx_dev->mdm_reset_wait,
+				 test_bit(MR_COMPLETE,
+					  &ifx_dev->mdm_reset_state),
+				 IFX_RESET_TIMEOUT);
+	if (!ret)
+		dev_warn(&ifx_dev->spi_dev->dev, "Modem reset timeout: (state:%lx)",
+			 ifx_dev->mdm_reset_state);
+
+	ifx_dev->mdm_reset_state = 0;
+	return ret;
+}
+
+/**
+ *	ifx_spi_spi_probe	-	probe callback
+ *	@spi: our possible matching SPI device
+ *
+ *	Probe for a 6x60 modem on SPI bus. Perform any needed device and
+ *	GPIO setup.
+ *
+ *	FIXME:
+ *	-	Support for multiple devices
+ *	-	Split out MID specific GPIO handling eventually
+ */
+
+static int ifx_spi_spi_probe(struct spi_device *spi)
+{
+	int ret;
+	int srdy;
+	struct ifx_modem_platform_data *pl_data = NULL;
+	struct ifx_spi_device *ifx_dev;
+
+	if (saved_ifx_dev) {
+		dev_dbg(&spi->dev, "ignoring subsequent detection");
+		return -ENODEV;
+	}
+
+	/* initialize structure to hold our device variables */
+	ifx_dev = kzalloc(sizeof(struct ifx_spi_device), GFP_KERNEL);
+	if (!ifx_dev) {
+		dev_err(&spi->dev, "spi device allocation failed");
+		return -ENOMEM;
+	}
+	saved_ifx_dev = ifx_dev;
+	ifx_dev->spi_dev = spi;
+	clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags);
+	spin_lock_init(&ifx_dev->write_lock);
+	spin_lock_init(&ifx_dev->power_lock);
+	ifx_dev->power_status = 0;
+	init_timer(&ifx_dev->spi_timer);
+	ifx_dev->spi_timer.function = ifx_spi_timeout;
+	ifx_dev->spi_timer.data = (unsigned long)ifx_dev;
+	ifx_dev->is_6160 = pl_data->is_6160;
+
+	/* ensure SPI protocol flags are initialized to enable transfer */
+	ifx_dev->spi_more = 0;
+	ifx_dev->spi_slave_cts = 0;
+
+	/*initialize transfer and dma buffers */
+	ifx_dev->tx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev,
+				IFX_SPI_TRANSFER_SIZE,
+				&ifx_dev->tx_bus,
+				GFP_KERNEL);
+	if (!ifx_dev->tx_buffer) {
+		dev_err(&spi->dev, "DMA-TX buffer allocation failed");
+		ret = -ENOMEM;
+		goto error_ret;
+	}
+	ifx_dev->rx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev,
+				IFX_SPI_TRANSFER_SIZE,
+				&ifx_dev->rx_bus,
+				GFP_KERNEL);
+	if (!ifx_dev->rx_buffer) {
+		dev_err(&spi->dev, "DMA-RX buffer allocation failed");
+		ret = -ENOMEM;
+		goto error_ret;
+	}
+
+	/* initialize waitq for modem reset */
+	init_waitqueue_head(&ifx_dev->mdm_reset_wait);
+
+	spi_set_drvdata(spi, ifx_dev);
+	tasklet_init(&ifx_dev->io_work_tasklet, ifx_spi_io,
+						(unsigned long)ifx_dev);
+
+	set_bit(IFX_SPI_STATE_PRESENT, &ifx_dev->flags);
+
+	/* create our tty port */
+	ret = ifx_spi_create_port(ifx_dev);
+	if (ret != 0) {
+		dev_err(&spi->dev, "create default tty port failed");
+		goto error_ret;
+	}
+
+	pl_data = (struct ifx_modem_platform_data *)spi->dev.platform_data;
+	if (pl_data) {
+		ifx_dev->gpio.reset = pl_data->rst_pmu;
+		ifx_dev->gpio.po = pl_data->pwr_on;
+		ifx_dev->gpio.mrdy = pl_data->mrdy;
+		ifx_dev->gpio.srdy = pl_data->srdy;
+		ifx_dev->gpio.reset_out = pl_data->rst_out;
+	} else {
+		dev_err(&spi->dev, "missing platform data!");
+		ret = -ENODEV;
+		goto error_ret;
+	}
+
+	dev_info(&spi->dev, "gpios %d, %d, %d, %d, %d",
+		 ifx_dev->gpio.reset, ifx_dev->gpio.po, ifx_dev->gpio.mrdy,
+		 ifx_dev->gpio.srdy, ifx_dev->gpio.reset_out);
+
+	/* Configure gpios */
+	ret = gpio_request(ifx_dev->gpio.reset, "ifxModem");
+	if (ret < 0) {
+		dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET)",
+			ifx_dev->gpio.reset);
+		goto error_ret;
+	}
+	ret += gpio_direction_output(ifx_dev->gpio.reset, 0);
+	ret += gpio_export(ifx_dev->gpio.reset, 1);
+	if (ret) {
+		dev_err(&spi->dev, "Unable to configure GPIO%d (RESET)",
+			ifx_dev->gpio.reset);
+		ret = -EBUSY;
+		goto error_ret2;
+	}
+
+	ret = gpio_request(ifx_dev->gpio.po, "ifxModem");
+	ret += gpio_direction_output(ifx_dev->gpio.po, 0);
+	ret += gpio_export(ifx_dev->gpio.po, 1);
+	if (ret) {
+		dev_err(&spi->dev, "Unable to configure GPIO%d (ON)",
+			ifx_dev->gpio.po);
+		ret = -EBUSY;
+		goto error_ret3;
+	}
+
+	ret = gpio_request(ifx_dev->gpio.mrdy, "ifxModem");
+	if (ret < 0) {
+		dev_err(&spi->dev, "Unable to allocate GPIO%d (MRDY)",
+			ifx_dev->gpio.mrdy);
+		goto error_ret3;
+	}
+	ret += gpio_export(ifx_dev->gpio.mrdy, 1);
+	ret += gpio_direction_output(ifx_dev->gpio.mrdy, 0);
+	if (ret) {
+		dev_err(&spi->dev, "Unable to configure GPIO%d (MRDY)",
+			ifx_dev->gpio.mrdy);
+		ret = -EBUSY;
+		goto error_ret4;
+	}
+
+	ret = gpio_request(ifx_dev->gpio.srdy, "ifxModem");
+	if (ret < 0) {
+		dev_err(&spi->dev, "Unable to allocate GPIO%d (SRDY)",
+			ifx_dev->gpio.srdy);
+		ret = -EBUSY;
+		goto error_ret4;
+	}
+	ret += gpio_export(ifx_dev->gpio.srdy, 1);
+	ret += gpio_direction_input(ifx_dev->gpio.srdy);
+	if (ret) {
+		dev_err(&spi->dev, "Unable to configure GPIO%d (SRDY)",
+			ifx_dev->gpio.srdy);
+		ret = -EBUSY;
+		goto error_ret5;
+	}
+
+	ret = gpio_request(ifx_dev->gpio.reset_out, "ifxModem");
+	if (ret < 0) {
+		dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET_OUT)",
+			ifx_dev->gpio.reset_out);
+		goto error_ret5;
+	}
+	ret += gpio_export(ifx_dev->gpio.reset_out, 1);
+	ret += gpio_direction_input(ifx_dev->gpio.reset_out);
+	if (ret) {
+		dev_err(&spi->dev, "Unable to configure GPIO%d (RESET_OUT)",
+			ifx_dev->gpio.reset_out);
+		ret = -EBUSY;
+		goto error_ret6;
+	}
+
+	ret = request_irq(gpio_to_irq(ifx_dev->gpio.reset_out),
+			  ifx_spi_reset_interrupt,
+			  IRQF_TRIGGER_RISING|IRQF_TRIGGER_FALLING, DRVNAME,
+		(void *)ifx_dev);
+	if (ret) {
+		dev_err(&spi->dev, "Unable to get irq %x\n",
+			gpio_to_irq(ifx_dev->gpio.reset_out));
+		goto error_ret6;
+	}
+
+	ret = ifx_spi_reset(ifx_dev);
+
+	ret = request_irq(gpio_to_irq(ifx_dev->gpio.srdy),
+			  ifx_spi_srdy_interrupt,
+			  IRQF_TRIGGER_RISING, DRVNAME,
+			  (void *)ifx_dev);
+	if (ret) {
+		dev_err(&spi->dev, "Unable to get irq %x",
+			gpio_to_irq(ifx_dev->gpio.srdy));
+		goto error_ret7;
+	}
+
+	/* set pm runtime power state and register with power system */
+	pm_runtime_set_active(&spi->dev);
+	pm_runtime_enable(&spi->dev);
+
+	/* handle case that modem is already signaling SRDY */
+	/* no outgoing tty open at this point, this just satisfies the
+	 * modem's read and should reset communication properly
+	 */
+	srdy = gpio_get_value(ifx_dev->gpio.srdy);
+
+	if (srdy) {
+		mrdy_assert(ifx_dev);
+		ifx_spi_handle_srdy(ifx_dev);
+	} else
+		mrdy_set_low(ifx_dev);
+	return 0;
+
+error_ret7:
+	free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev);
+error_ret6:
+	gpio_free(ifx_dev->gpio.srdy);
+error_ret5:
+	gpio_free(ifx_dev->gpio.mrdy);
+error_ret4:
+	gpio_free(ifx_dev->gpio.reset);
+error_ret3:
+	gpio_free(ifx_dev->gpio.po);
+error_ret2:
+	gpio_free(ifx_dev->gpio.reset_out);
+error_ret:
+	ifx_spi_free_device(ifx_dev);
+	saved_ifx_dev = NULL;
+	return ret;
+}
+
+/**
+ *	ifx_spi_spi_remove	-	SPI device was removed
+ *	@spi: SPI device
+ *
+ *	FIXME: We should be shutting the device down here not in
+ *	the module unload path.
+ */
+
+static int ifx_spi_spi_remove(struct spi_device *spi)
+{
+	struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi);
+	/* stop activity */
+	tasklet_kill(&ifx_dev->io_work_tasklet);
+	/* free irq */
+	free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev);
+	free_irq(gpio_to_irq(ifx_dev->gpio.srdy), (void *)ifx_dev);
+
+	gpio_free(ifx_dev->gpio.srdy);
+	gpio_free(ifx_dev->gpio.mrdy);
+	gpio_free(ifx_dev->gpio.reset);
+	gpio_free(ifx_dev->gpio.po);
+	gpio_free(ifx_dev->gpio.reset_out);
+
+	/* free allocations */
+	ifx_spi_free_device(ifx_dev);
+
+	saved_ifx_dev = NULL;
+	return 0;
+}
+
+/**
+ *	ifx_spi_spi_shutdown	-	called on SPI shutdown
+ *	@spi: SPI device
+ *
+ *	No action needs to be taken here
+ */
+
+static void ifx_spi_spi_shutdown(struct spi_device *spi)
+{
+}
+
+/*
+ * various suspends and resumes have nothing to do
+ * no hardware to save state for
+ */
+
+/**
+ *	ifx_spi_spi_suspend	-	suspend SPI on system suspend
+ *	@dev: device being suspended
+ *
+ *	Suspend the SPI side. No action needed on Intel MID platforms, may
+ *	need extending for other systems.
+ */
+static int ifx_spi_spi_suspend(struct spi_device *spi, pm_message_t msg)
+{
+	return 0;
+}
+
+/**
+ *	ifx_spi_spi_resume	-	resume SPI side on system resume
+ *	@dev: device being suspended
+ *
+ *	Suspend the SPI side. No action needed on Intel MID platforms, may
+ *	need extending for other systems.
+ */
+static int ifx_spi_spi_resume(struct spi_device *spi)
+{
+	return 0;
+}
+
+/**
+ *	ifx_spi_pm_suspend	-	suspend modem on system suspend
+ *	@dev: device being suspended
+ *
+ *	Suspend the modem. No action needed on Intel MID platforms, may
+ *	need extending for other systems.
+ */
+static int ifx_spi_pm_suspend(struct device *dev)
+{
+	return 0;
+}
+
+/**
+ *	ifx_spi_pm_resume	-	resume modem on system resume
+ *	@dev: device being suspended
+ *
+ *	Allow the modem to resume. No action needed.
+ *
+ *	FIXME: do we need to reset anything here ?
+ */
+static int ifx_spi_pm_resume(struct device *dev)
+{
+	return 0;
+}
+
+/**
+ *	ifx_spi_pm_runtime_resume	-	suspend modem
+ *	@dev: device being suspended
+ *
+ *	Allow the modem to resume. No action needed.
+ */
+static int ifx_spi_pm_runtime_resume(struct device *dev)
+{
+	return 0;
+}
+
+/**
+ *	ifx_spi_pm_runtime_suspend	-	suspend modem
+ *	@dev: device being suspended
+ *
+ *	Allow the modem to suspend and thus suspend to continue up the
+ *	device tree.
+ */
+static int ifx_spi_pm_runtime_suspend(struct device *dev)
+{
+	return 0;
+}
+
+/**
+ *	ifx_spi_pm_runtime_idle		-	check if modem idle
+ *	@dev: our device
+ *
+ *	Check conditions and queue runtime suspend if idle.
+ */
+static int ifx_spi_pm_runtime_idle(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi);
+
+	if (!ifx_dev->power_status)
+		pm_runtime_suspend(dev);
+
+	return 0;
+}
+
+static const struct dev_pm_ops ifx_spi_pm = {
+	.resume = ifx_spi_pm_resume,
+	.suspend = ifx_spi_pm_suspend,
+	.runtime_resume = ifx_spi_pm_runtime_resume,
+	.runtime_suspend = ifx_spi_pm_runtime_suspend,
+	.runtime_idle = ifx_spi_pm_runtime_idle
+};
+
+static const struct spi_device_id ifx_id_table[] = {
+	{"ifx6160", 0},
+	{"ifx6260", 0},
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ifx_id_table);
+
+/* spi operations */
+static const struct spi_driver ifx_spi_driver_6160 = {
+	.driver = {
+		.name = "ifx6160",
+		.bus = &spi_bus_type,
+		.pm = &ifx_spi_pm,
+		.owner = THIS_MODULE},
+	.probe = ifx_spi_spi_probe,
+	.shutdown = ifx_spi_spi_shutdown,
+	.remove = __devexit_p(ifx_spi_spi_remove),
+	.suspend = ifx_spi_spi_suspend,
+	.resume = ifx_spi_spi_resume,
+	.id_table = ifx_id_table
+};
+
+/**
+ *	ifx_spi_exit	-	module exit
+ *
+ *	Unload the module.
+ */
+
+static void __exit ifx_spi_exit(void)
+{
+	/* unregister */
+	tty_unregister_driver(tty_drv);
+	spi_unregister_driver((void *)&ifx_spi_driver_6160);
+}
+
+/**
+ *	ifx_spi_init		-	module entry point
+ *
+ *	Initialise the SPI and tty interfaces for the IFX SPI driver
+ *	We need to initialize upper-edge spi driver after the tty
+ *	driver because otherwise the spi probe will race
+ */
+
+static int __init ifx_spi_init(void)
+{
+	int result;
+
+	tty_drv = alloc_tty_driver(1);
+	if (!tty_drv) {
+		pr_err("%s: alloc_tty_driver failed", DRVNAME);
+		return -ENOMEM;
+	}
+
+	tty_drv->magic = TTY_DRIVER_MAGIC;
+	tty_drv->owner = THIS_MODULE;
+	tty_drv->driver_name = DRVNAME;
+	tty_drv->name = TTYNAME;
+	tty_drv->minor_start = IFX_SPI_TTY_ID;
+	tty_drv->num = 1;
+	tty_drv->type = TTY_DRIVER_TYPE_SERIAL;
+	tty_drv->subtype = SERIAL_TYPE_NORMAL;
+	tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	tty_drv->init_termios = tty_std_termios;
+
+	tty_set_operations(tty_drv, &ifx_spi_serial_ops);
+
+	result = tty_register_driver(tty_drv);
+	if (result) {
+		pr_err("%s: tty_register_driver failed(%d)",
+			DRVNAME, result);
+		put_tty_driver(tty_drv);
+		return result;
+	}
+
+	result = spi_register_driver((void *)&ifx_spi_driver_6160);
+	if (result) {
+		pr_err("%s: spi_register_driver failed(%d)",
+			DRVNAME, result);
+		tty_unregister_driver(tty_drv);
+	}
+	return result;
+}
+
+module_init(ifx_spi_init);
+module_exit(ifx_spi_exit);
+
+MODULE_AUTHOR("Intel");
+MODULE_DESCRIPTION("IFX6x60 spi driver");
+MODULE_LICENSE("GPL");
+MODULE_INFO(Version, "0.1-IFX6x60");
diff --git a/drivers/serial/ifx6x60.h b/drivers/serial/ifx6x60.h
new file mode 100644
index 000000000000..deb7b8d977dc
--- /dev/null
+++ b/drivers/serial/ifx6x60.h
@@ -0,0 +1,129 @@
+/****************************************************************************
+ *
+ * Driver for the IFX spi modem.
+ *
+ * Copyright (C) 2009, 2010 Intel Corp
+ * Jim Stanley <jim.stanley@intel.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301,
+ * USA
+ *
+ *
+ *
+ *****************************************************************************/
+#ifndef _IFX6X60_H
+#define _IFX6X60_H
+
+#define DRVNAME				"ifx6x60"
+#define TTYNAME				"ttyIFX"
+
+/* #define IFX_THROTTLE_CODE */
+
+#define IFX_SPI_MAX_MINORS		1
+#define IFX_SPI_TRANSFER_SIZE		2048
+#define IFX_SPI_FIFO_SIZE		4096
+
+#define IFX_SPI_HEADER_OVERHEAD		4
+#define IFX_RESET_TIMEOUT		msecs_to_jiffies(50)
+
+/* device flags bitfield definitions */
+#define IFX_SPI_STATE_PRESENT		0
+#define IFX_SPI_STATE_IO_IN_PROGRESS	1
+#define IFX_SPI_STATE_IO_READY		2
+#define IFX_SPI_STATE_TIMER_PENDING	3
+
+/* flow control bitfields */
+#define IFX_SPI_DCD			0
+#define IFX_SPI_CTS			1
+#define IFX_SPI_DSR			2
+#define IFX_SPI_RI			3
+#define IFX_SPI_DTR			4
+#define IFX_SPI_RTS			5
+#define IFX_SPI_TX_FC			6
+#define IFX_SPI_RX_FC			7
+#define IFX_SPI_UPDATE			8
+
+#define IFX_SPI_PAYLOAD_SIZE		(IFX_SPI_TRANSFER_SIZE - \
+						IFX_SPI_HEADER_OVERHEAD)
+
+#define IFX_SPI_IRQ_TYPE		DETECT_EDGE_RISING
+#define IFX_SPI_GPIO_TARGET		0
+#define IFX_SPI_GPIO0			0x105
+
+#define IFX_SPI_STATUS_TIMEOUT		(2000*HZ)
+
+/* values for bits in power status byte */
+#define IFX_SPI_POWER_DATA_PENDING	1
+#define IFX_SPI_POWER_SRDY		2
+
+struct ifx_spi_device {
+	/* Our SPI device */
+	struct spi_device *spi_dev;
+
+	/* Port specific data */
+	struct kfifo tx_fifo;
+	spinlock_t fifo_lock;
+	unsigned long signal_state;
+
+	/* TTY Layer logic */
+	struct tty_port tty_port;
+	struct device *tty_dev;
+	int minor;
+
+	/* Low level I/O work */
+	struct tasklet_struct io_work_tasklet;
+	unsigned long flags;
+	dma_addr_t rx_dma;
+	dma_addr_t tx_dma;
+
+	int is_6160;				/* Modem type */
+
+	spinlock_t write_lock;
+	int write_pending;
+	spinlock_t power_lock;
+	unsigned char power_status;
+
+	unsigned char *rx_buffer;
+	unsigned char *tx_buffer;
+	dma_addr_t rx_bus;
+	dma_addr_t tx_bus;
+	unsigned char spi_more;
+	unsigned char spi_slave_cts;
+
+	struct timer_list spi_timer;
+
+	struct spi_message spi_msg;
+	struct spi_transfer spi_xfer;
+
+	struct {
+		/* gpio lines */
+		unsigned short srdy;		/* slave-ready gpio */
+		unsigned short mrdy;		/* master-ready gpio */
+		unsigned short reset;		/* modem-reset gpio */
+		unsigned short po;		/* modem-on gpio */
+		unsigned short reset_out;	/* modem-in-reset gpio */
+		/* state/stats */
+		int unack_srdy_int_nb;
+	} gpio;
+
+	/* modem reset */
+	unsigned long mdm_reset_state;
+#define MR_START	0
+#define MR_INPROGRESS	1
+#define MR_COMPLETE	2
+	wait_queue_head_t mdm_reset_wait;
+};
+
+#endif /* _IFX6X60_H */
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index c4399e23565a..126ec7f568ec 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -838,7 +838,11 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new,
 static const char *
 mpc52xx_uart_type(struct uart_port *port)
 {
-	return port->type == PORT_MPC52xx ? "MPC52xx PSC" : NULL;
+	/*
+	 * We keep using PORT_MPC52xx for historic reasons although it applies
+	 * for MPC512x, too, but print "MPC5xxx" to not irritate users
+	 */
+	return port->type == PORT_MPC52xx ? "MPC5xxx PSC" : NULL;
 }
 
 static void
diff --git a/drivers/serial/omap-serial.c b/drivers/serial/omap-serial.c
index 1201eff1831e..7f2f01058789 100644
--- a/drivers/serial/omap-serial.c
+++ b/drivers/serial/omap-serial.c
@@ -866,12 +866,6 @@ serial_omap_type(struct uart_port *port)
 	return up->name;
 }
 
-#ifdef CONFIG_SERIAL_OMAP_CONSOLE
-
-static struct uart_omap_port *serial_omap_console_ports[4];
-
-static struct uart_driver serial_omap_reg;
-
 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
 
 static inline void wait_for_xmitr(struct uart_omap_port *up)
@@ -905,6 +899,34 @@ static inline void wait_for_xmitr(struct uart_omap_port *up)
 	}
 }
 
+#ifdef CONFIG_CONSOLE_POLL
+
+static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
+{
+	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	wait_for_xmitr(up);
+	serial_out(up, UART_TX, ch);
+}
+
+static int serial_omap_poll_get_char(struct uart_port *port)
+{
+	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	unsigned int status = serial_in(up, UART_LSR);
+
+	if (!(status & UART_LSR_DR))
+		return NO_POLL_CHAR;
+
+	return serial_in(up, UART_RX);
+}
+
+#endif /* CONFIG_CONSOLE_POLL */
+
+#ifdef CONFIG_SERIAL_OMAP_CONSOLE
+
+static struct uart_omap_port *serial_omap_console_ports[4];
+
+static struct uart_driver serial_omap_reg;
+
 static void serial_omap_console_putchar(struct uart_port *port, int ch)
 {
 	struct uart_omap_port *up = (struct uart_omap_port *)port;
@@ -1022,6 +1044,10 @@ static struct uart_ops serial_omap_pops = {
 	.request_port	= serial_omap_request_port,
 	.config_port	= serial_omap_config_port,
 	.verify_port	= serial_omap_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_put_char  = serial_omap_poll_put_char,
+	.poll_get_char  = serial_omap_poll_get_char,
+#endif
 };
 
 static struct uart_driver serial_omap_reg = {
diff --git a/drivers/serial/pch_uart.c b/drivers/serial/pch_uart.c
new file mode 100644
index 000000000000..70a61458ec42
--- /dev/null
+++ b/drivers/serial/pch_uart.c
@@ -0,0 +1,1451 @@
+/*
+ *Copyright (C) 2010 OKI SEMICONDUCTOR CO., LTD.
+ *
+ *This program is free software; you can redistribute it and/or modify
+ *it under the terms of the GNU General Public License as published by
+ *the Free Software Foundation; version 2 of the License.
+ *
+ *This program is distributed in the hope that it will be useful,
+ *but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *GNU General Public License for more details.
+ *
+ *You should have received a copy of the GNU General Public License
+ *along with this program; if not, write to the Free Software
+ *Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307, USA.
+ */
+#include <linux/serial_reg.h>
+#include <linux/pci.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/serial_core.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+
+#include <linux/dmaengine.h>
+#include <linux/pch_dma.h>
+
+enum {
+	PCH_UART_HANDLED_RX_INT_SHIFT,
+	PCH_UART_HANDLED_TX_INT_SHIFT,
+	PCH_UART_HANDLED_RX_ERR_INT_SHIFT,
+	PCH_UART_HANDLED_RX_TRG_INT_SHIFT,
+	PCH_UART_HANDLED_MS_INT_SHIFT,
+};
+
+enum {
+	PCH_UART_8LINE,
+	PCH_UART_2LINE,
+};
+
+#define PCH_UART_DRIVER_DEVICE "ttyPCH"
+
+#define PCH_UART_NR_GE_256FIFO		1
+#define PCH_UART_NR_GE_64FIFO		3
+#define PCH_UART_NR_GE	(PCH_UART_NR_GE_256FIFO+PCH_UART_NR_GE_64FIFO)
+#define PCH_UART_NR	PCH_UART_NR_GE
+
+#define PCH_UART_HANDLED_RX_INT	(1<<((PCH_UART_HANDLED_RX_INT_SHIFT)<<1))
+#define PCH_UART_HANDLED_TX_INT	(1<<((PCH_UART_HANDLED_TX_INT_SHIFT)<<1))
+#define PCH_UART_HANDLED_RX_ERR_INT	(1<<((\
+					PCH_UART_HANDLED_RX_ERR_INT_SHIFT)<<1))
+#define PCH_UART_HANDLED_RX_TRG_INT	(1<<((\
+					PCH_UART_HANDLED_RX_TRG_INT_SHIFT)<<1))
+#define PCH_UART_HANDLED_MS_INT	(1<<((PCH_UART_HANDLED_MS_INT_SHIFT)<<1))
+
+#define PCH_UART_RBR		0x00
+#define PCH_UART_THR		0x00
+
+#define PCH_UART_IER_MASK	(PCH_UART_IER_ERBFI|PCH_UART_IER_ETBEI|\
+				PCH_UART_IER_ELSI|PCH_UART_IER_EDSSI)
+#define PCH_UART_IER_ERBFI	0x00000001
+#define PCH_UART_IER_ETBEI	0x00000002
+#define PCH_UART_IER_ELSI	0x00000004
+#define PCH_UART_IER_EDSSI	0x00000008
+
+#define PCH_UART_IIR_IP			0x00000001
+#define PCH_UART_IIR_IID		0x00000006
+#define PCH_UART_IIR_MSI		0x00000000
+#define PCH_UART_IIR_TRI		0x00000002
+#define PCH_UART_IIR_RRI		0x00000004
+#define PCH_UART_IIR_REI		0x00000006
+#define PCH_UART_IIR_TOI		0x00000008
+#define PCH_UART_IIR_FIFO256		0x00000020
+#define PCH_UART_IIR_FIFO64		PCH_UART_IIR_FIFO256
+#define PCH_UART_IIR_FE			0x000000C0
+
+#define PCH_UART_FCR_FIFOE		0x00000001
+#define PCH_UART_FCR_RFR		0x00000002
+#define PCH_UART_FCR_TFR		0x00000004
+#define PCH_UART_FCR_DMS		0x00000008
+#define PCH_UART_FCR_FIFO256		0x00000020
+#define PCH_UART_FCR_RFTL		0x000000C0
+
+#define PCH_UART_FCR_RFTL1		0x00000000
+#define PCH_UART_FCR_RFTL64		0x00000040
+#define PCH_UART_FCR_RFTL128		0x00000080
+#define PCH_UART_FCR_RFTL224		0x000000C0
+#define PCH_UART_FCR_RFTL16		PCH_UART_FCR_RFTL64
+#define PCH_UART_FCR_RFTL32		PCH_UART_FCR_RFTL128
+#define PCH_UART_FCR_RFTL56		PCH_UART_FCR_RFTL224
+#define PCH_UART_FCR_RFTL4		PCH_UART_FCR_RFTL64
+#define PCH_UART_FCR_RFTL8		PCH_UART_FCR_RFTL128
+#define PCH_UART_FCR_RFTL14		PCH_UART_FCR_RFTL224
+#define PCH_UART_FCR_RFTL_SHIFT		6
+
+#define PCH_UART_LCR_WLS	0x00000003
+#define PCH_UART_LCR_STB	0x00000004
+#define PCH_UART_LCR_PEN	0x00000008
+#define PCH_UART_LCR_EPS	0x00000010
+#define PCH_UART_LCR_SP		0x00000020
+#define PCH_UART_LCR_SB		0x00000040
+#define PCH_UART_LCR_DLAB	0x00000080
+#define PCH_UART_LCR_NP		0x00000000
+#define PCH_UART_LCR_OP		PCH_UART_LCR_PEN
+#define PCH_UART_LCR_EP		(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS)
+#define PCH_UART_LCR_1P		(PCH_UART_LCR_PEN | PCH_UART_LCR_SP)
+#define PCH_UART_LCR_0P		(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS |\
+				PCH_UART_LCR_SP)
+
+#define PCH_UART_LCR_5BIT	0x00000000
+#define PCH_UART_LCR_6BIT	0x00000001
+#define PCH_UART_LCR_7BIT	0x00000002
+#define PCH_UART_LCR_8BIT	0x00000003
+
+#define PCH_UART_MCR_DTR	0x00000001
+#define PCH_UART_MCR_RTS	0x00000002
+#define PCH_UART_MCR_OUT	0x0000000C
+#define PCH_UART_MCR_LOOP	0x00000010
+#define PCH_UART_MCR_AFE	0x00000020
+
+#define PCH_UART_LSR_DR		0x00000001
+#define PCH_UART_LSR_ERR	(1<<7)
+
+#define PCH_UART_MSR_DCTS	0x00000001
+#define PCH_UART_MSR_DDSR	0x00000002
+#define PCH_UART_MSR_TERI	0x00000004
+#define PCH_UART_MSR_DDCD	0x00000008
+#define PCH_UART_MSR_CTS	0x00000010
+#define PCH_UART_MSR_DSR	0x00000020
+#define PCH_UART_MSR_RI		0x00000040
+#define PCH_UART_MSR_DCD	0x00000080
+#define PCH_UART_MSR_DELTA	(PCH_UART_MSR_DCTS | PCH_UART_MSR_DDSR |\
+				PCH_UART_MSR_TERI | PCH_UART_MSR_DDCD)
+
+#define PCH_UART_DLL		0x00
+#define PCH_UART_DLM		0x01
+
+#define DIV_ROUND(a, b)	(((a) + ((b)/2)) / (b))
+
+#define PCH_UART_IID_RLS	(PCH_UART_IIR_REI)
+#define PCH_UART_IID_RDR	(PCH_UART_IIR_RRI)
+#define PCH_UART_IID_RDR_TO	(PCH_UART_IIR_RRI | PCH_UART_IIR_TOI)
+#define PCH_UART_IID_THRE	(PCH_UART_IIR_TRI)
+#define PCH_UART_IID_MS		(PCH_UART_IIR_MSI)
+
+#define PCH_UART_HAL_PARITY_NONE	(PCH_UART_LCR_NP)
+#define PCH_UART_HAL_PARITY_ODD		(PCH_UART_LCR_OP)
+#define PCH_UART_HAL_PARITY_EVEN	(PCH_UART_LCR_EP)
+#define PCH_UART_HAL_PARITY_FIX1	(PCH_UART_LCR_1P)
+#define PCH_UART_HAL_PARITY_FIX0	(PCH_UART_LCR_0P)
+#define PCH_UART_HAL_5BIT		(PCH_UART_LCR_5BIT)
+#define PCH_UART_HAL_6BIT		(PCH_UART_LCR_6BIT)
+#define PCH_UART_HAL_7BIT		(PCH_UART_LCR_7BIT)
+#define PCH_UART_HAL_8BIT		(PCH_UART_LCR_8BIT)
+#define PCH_UART_HAL_STB1		0
+#define PCH_UART_HAL_STB2		(PCH_UART_LCR_STB)
+
+#define PCH_UART_HAL_CLR_TX_FIFO	(PCH_UART_FCR_TFR)
+#define PCH_UART_HAL_CLR_RX_FIFO	(PCH_UART_FCR_RFR)
+#define PCH_UART_HAL_CLR_ALL_FIFO	(PCH_UART_HAL_CLR_TX_FIFO | \
+					PCH_UART_HAL_CLR_RX_FIFO)
+
+#define PCH_UART_HAL_DMA_MODE0		0
+#define PCH_UART_HAL_FIFO_DIS		0
+#define PCH_UART_HAL_FIFO16		(PCH_UART_FCR_FIFOE)
+#define PCH_UART_HAL_FIFO256		(PCH_UART_FCR_FIFOE | \
+					PCH_UART_FCR_FIFO256)
+#define PCH_UART_HAL_FIFO64		(PCH_UART_HAL_FIFO256)
+#define PCH_UART_HAL_TRIGGER1		(PCH_UART_FCR_RFTL1)
+#define PCH_UART_HAL_TRIGGER64		(PCH_UART_FCR_RFTL64)
+#define PCH_UART_HAL_TRIGGER128		(PCH_UART_FCR_RFTL128)
+#define PCH_UART_HAL_TRIGGER224		(PCH_UART_FCR_RFTL224)
+#define PCH_UART_HAL_TRIGGER16		(PCH_UART_FCR_RFTL16)
+#define PCH_UART_HAL_TRIGGER32		(PCH_UART_FCR_RFTL32)
+#define PCH_UART_HAL_TRIGGER56		(PCH_UART_FCR_RFTL56)
+#define PCH_UART_HAL_TRIGGER4		(PCH_UART_FCR_RFTL4)
+#define PCH_UART_HAL_TRIGGER8		(PCH_UART_FCR_RFTL8)
+#define PCH_UART_HAL_TRIGGER14		(PCH_UART_FCR_RFTL14)
+#define PCH_UART_HAL_TRIGGER_L		(PCH_UART_FCR_RFTL64)
+#define PCH_UART_HAL_TRIGGER_M		(PCH_UART_FCR_RFTL128)
+#define PCH_UART_HAL_TRIGGER_H		(PCH_UART_FCR_RFTL224)
+
+#define PCH_UART_HAL_RX_INT		(PCH_UART_IER_ERBFI)
+#define PCH_UART_HAL_TX_INT		(PCH_UART_IER_ETBEI)
+#define PCH_UART_HAL_RX_ERR_INT		(PCH_UART_IER_ELSI)
+#define PCH_UART_HAL_MS_INT		(PCH_UART_IER_EDSSI)
+#define PCH_UART_HAL_ALL_INT		(PCH_UART_IER_MASK)
+
+#define PCH_UART_HAL_DTR		(PCH_UART_MCR_DTR)
+#define PCH_UART_HAL_RTS		(PCH_UART_MCR_RTS)
+#define PCH_UART_HAL_OUT		(PCH_UART_MCR_OUT)
+#define PCH_UART_HAL_LOOP		(PCH_UART_MCR_LOOP)
+#define PCH_UART_HAL_AFE		(PCH_UART_MCR_AFE)
+
+struct pch_uart_buffer {
+	unsigned char *buf;
+	int size;
+};
+
+struct eg20t_port {
+	struct uart_port port;
+	int port_type;
+	void __iomem *membase;
+	resource_size_t mapbase;
+	unsigned int iobase;
+	struct pci_dev *pdev;
+	int fifo_size;
+	int base_baud;
+	int start_tx;
+	int start_rx;
+	int tx_empty;
+	int int_dis_flag;
+	int trigger;
+	int trigger_level;
+	struct pch_uart_buffer rxbuf;
+	unsigned int dmsr;
+	unsigned int fcr;
+	unsigned int use_dma;
+	unsigned int use_dma_flag;
+	struct dma_async_tx_descriptor	*desc_tx;
+	struct dma_async_tx_descriptor	*desc_rx;
+	struct pch_dma_slave		param_tx;
+	struct pch_dma_slave		param_rx;
+	struct dma_chan			*chan_tx;
+	struct dma_chan			*chan_rx;
+	struct scatterlist		sg_tx;
+	struct scatterlist		sg_rx;
+	int				tx_dma_use;
+	void				*rx_buf_virt;
+	dma_addr_t			rx_buf_dma;
+};
+
+static unsigned int default_baud = 9600;
+static const int trigger_level_256[4] = { 1, 64, 128, 224 };
+static const int trigger_level_64[4] = { 1, 16, 32, 56 };
+static const int trigger_level_16[4] = { 1, 4, 8, 14 };
+static const int trigger_level_1[4] = { 1, 1, 1, 1 };
+
+static void pch_uart_hal_request(struct pci_dev *pdev, int fifosize,
+				 int base_baud)
+{
+	struct eg20t_port *priv = pci_get_drvdata(pdev);
+
+	priv->trigger_level = 1;
+	priv->fcr = 0;
+}
+
+static unsigned int get_msr(struct eg20t_port *priv, void __iomem *base)
+{
+	unsigned int msr = ioread8(base + UART_MSR);
+	priv->dmsr |= msr & PCH_UART_MSR_DELTA;
+
+	return msr;
+}
+
+static void pch_uart_hal_enable_interrupt(struct eg20t_port *priv,
+					  unsigned int flag)
+{
+	u8 ier = ioread8(priv->membase + UART_IER);
+	ier |= flag & PCH_UART_IER_MASK;
+	iowrite8(ier, priv->membase + UART_IER);
+}
+
+static void pch_uart_hal_disable_interrupt(struct eg20t_port *priv,
+					   unsigned int flag)
+{
+	u8 ier = ioread8(priv->membase + UART_IER);
+	ier &= ~(flag & PCH_UART_IER_MASK);
+	iowrite8(ier, priv->membase + UART_IER);
+}
+
+static int pch_uart_hal_set_line(struct eg20t_port *priv, int baud,
+				 unsigned int parity, unsigned int bits,
+				 unsigned int stb)
+{
+	unsigned int dll, dlm, lcr;
+	int div;
+
+	div = DIV_ROUND(priv->base_baud / 16, baud);
+	if (div < 0 || USHRT_MAX <= div) {
+		pr_err("Invalid Baud(div=0x%x)\n", div);
+		return -EINVAL;
+	}
+
+	dll = (unsigned int)div & 0x00FFU;
+	dlm = ((unsigned int)div >> 8) & 0x00FFU;
+
+	if (parity & ~(PCH_UART_LCR_PEN | PCH_UART_LCR_EPS | PCH_UART_LCR_SP)) {
+		pr_err("Invalid parity(0x%x)\n", parity);
+		return -EINVAL;
+	}
+
+	if (bits & ~PCH_UART_LCR_WLS) {
+		pr_err("Invalid bits(0x%x)\n", bits);
+		return -EINVAL;
+	}
+
+	if (stb & ~PCH_UART_LCR_STB) {
+		pr_err("Invalid STB(0x%x)\n", stb);
+		return -EINVAL;
+	}
+
+	lcr = parity;
+	lcr |= bits;
+	lcr |= stb;
+
+	pr_debug("%s:baud = %d, div = %04x, lcr = %02x (%lu)\n",
+		 __func__, baud, div, lcr, jiffies);
+	iowrite8(PCH_UART_LCR_DLAB, priv->membase + UART_LCR);
+	iowrite8(dll, priv->membase + PCH_UART_DLL);
+	iowrite8(dlm, priv->membase + PCH_UART_DLM);
+	iowrite8(lcr, priv->membase + UART_LCR);
+
+	return 0;
+}
+
+static int pch_uart_hal_fifo_reset(struct eg20t_port *priv,
+				    unsigned int flag)
+{
+	if (flag & ~(PCH_UART_FCR_TFR | PCH_UART_FCR_RFR)) {
+		pr_err("%s:Invalid flag(0x%x)\n", __func__, flag);
+		return -EINVAL;
+	}
+
+	iowrite8(PCH_UART_FCR_FIFOE | priv->fcr, priv->membase + UART_FCR);
+	iowrite8(PCH_UART_FCR_FIFOE | priv->fcr | flag,
+		 priv->membase + UART_FCR);
+	iowrite8(priv->fcr, priv->membase + UART_FCR);
+
+	return 0;
+}
+
+static int pch_uart_hal_set_fifo(struct eg20t_port *priv,
+				 unsigned int dmamode,
+				 unsigned int fifo_size, unsigned int trigger)
+{
+	u8 fcr;
+
+	if (dmamode & ~PCH_UART_FCR_DMS) {
+		pr_err("%s:Invalid DMA Mode(0x%x)\n", __func__, dmamode);
+		return -EINVAL;
+	}
+
+	if (fifo_size & ~(PCH_UART_FCR_FIFOE | PCH_UART_FCR_FIFO256)) {
+		pr_err("%s:Invalid FIFO SIZE(0x%x)\n", __func__, fifo_size);
+		return -EINVAL;
+	}
+
+	if (trigger & ~PCH_UART_FCR_RFTL) {
+		pr_err("%s:Invalid TRIGGER(0x%x)\n", __func__, trigger);
+		return -EINVAL;
+	}
+
+	switch (priv->fifo_size) {
+	case 256:
+		priv->trigger_level =
+		    trigger_level_256[trigger >> PCH_UART_FCR_RFTL_SHIFT];
+		break;
+	case 64:
+		priv->trigger_level =
+		    trigger_level_64[trigger >> PCH_UART_FCR_RFTL_SHIFT];
+		break;
+	case 16:
+		priv->trigger_level =
+		    trigger_level_16[trigger >> PCH_UART_FCR_RFTL_SHIFT];
+		break;
+	default:
+		priv->trigger_level =
+		    trigger_level_1[trigger >> PCH_UART_FCR_RFTL_SHIFT];
+		break;
+	}
+	fcr =
+	    dmamode | fifo_size | trigger | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR;
+	iowrite8(PCH_UART_FCR_FIFOE, priv->membase + UART_FCR);
+	iowrite8(PCH_UART_FCR_FIFOE | PCH_UART_FCR_RFR | PCH_UART_FCR_TFR,
+		 priv->membase + UART_FCR);
+	iowrite8(fcr, priv->membase + UART_FCR);
+	priv->fcr = fcr;
+
+	return 0;
+}
+
+static u8 pch_uart_hal_get_modem(struct eg20t_port *priv)
+{
+	priv->dmsr = 0;
+	return get_msr(priv, priv->membase);
+}
+
+static int pch_uart_hal_write(struct eg20t_port *priv,
+			      const unsigned char *buf, int tx_size)
+{
+	int i;
+	unsigned int thr;
+
+	for (i = 0; i < tx_size;) {
+		thr = buf[i++];
+		iowrite8(thr, priv->membase + PCH_UART_THR);
+	}
+	return i;
+}
+
+static int pch_uart_hal_read(struct eg20t_port *priv, unsigned char *buf,
+			     int rx_size)
+{
+	int i;
+	u8 rbr, lsr;
+
+	lsr = ioread8(priv->membase + UART_LSR);
+	for (i = 0, lsr = ioread8(priv->membase + UART_LSR);
+	     i < rx_size && lsr & UART_LSR_DR;
+	     lsr = ioread8(priv->membase + UART_LSR)) {
+		rbr = ioread8(priv->membase + PCH_UART_RBR);
+		buf[i++] = rbr;
+	}
+	return i;
+}
+
+static unsigned int pch_uart_hal_get_iid(struct eg20t_port *priv)
+{
+	unsigned int iir;
+	int ret;
+
+	iir = ioread8(priv->membase + UART_IIR);
+	ret = (iir & (PCH_UART_IIR_IID | PCH_UART_IIR_TOI | PCH_UART_IIR_IP));
+	return ret;
+}
+
+static u8 pch_uart_hal_get_line_status(struct eg20t_port *priv)
+{
+	return ioread8(priv->membase + UART_LSR);
+}
+
+static void pch_uart_hal_set_break(struct eg20t_port *priv, int on)
+{
+	unsigned int lcr;
+
+	lcr = ioread8(priv->membase + UART_LCR);
+	if (on)
+		lcr |= PCH_UART_LCR_SB;
+	else
+		lcr &= ~PCH_UART_LCR_SB;
+
+	iowrite8(lcr, priv->membase + UART_LCR);
+}
+
+static int push_rx(struct eg20t_port *priv, const unsigned char *buf,
+		   int size)
+{
+	struct uart_port *port;
+	struct tty_struct *tty;
+
+	port = &priv->port;
+	tty = tty_port_tty_get(&port->state->port);
+	if (!tty) {
+		pr_debug("%s:tty is busy now", __func__);
+		return -EBUSY;
+	}
+
+	tty_insert_flip_string(tty, buf, size);
+	tty_flip_buffer_push(tty);
+	tty_kref_put(tty);
+
+	return 0;
+}
+
+static int pop_tx_x(struct eg20t_port *priv, unsigned char *buf)
+{
+	int ret;
+	struct uart_port *port = &priv->port;
+
+	if (port->x_char) {
+		pr_debug("%s:X character send %02x (%lu)\n", __func__,
+			port->x_char, jiffies);
+		buf[0] = port->x_char;
+		port->x_char = 0;
+		ret = 1;
+	} else {
+		ret = 0;
+	}
+
+	return ret;
+}
+
+static int dma_push_rx(struct eg20t_port *priv, int size)
+{
+	struct tty_struct *tty;
+	int room;
+	struct uart_port *port = &priv->port;
+
+	port = &priv->port;
+	tty = tty_port_tty_get(&port->state->port);
+	if (!tty) {
+		pr_debug("%s:tty is busy now", __func__);
+		return 0;
+	}
+
+	room = tty_buffer_request_room(tty, size);
+
+	if (room < size)
+		dev_warn(port->dev, "Rx overrun: dropping %u bytes\n",
+			 size - room);
+	if (!room)
+		return room;
+
+	tty_insert_flip_string(tty, sg_virt(&priv->sg_rx), size);
+
+	port->icount.rx += room;
+	tty_kref_put(tty);
+
+	return room;
+}
+
+static void pch_free_dma(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	priv = container_of(port, struct eg20t_port, port);
+
+	if (priv->chan_tx) {
+		dma_release_channel(priv->chan_tx);
+		priv->chan_tx = NULL;
+	}
+	if (priv->chan_rx) {
+		dma_release_channel(priv->chan_rx);
+		priv->chan_rx = NULL;
+	}
+	if (sg_dma_address(&priv->sg_rx))
+		dma_free_coherent(port->dev, port->fifosize,
+				  sg_virt(&priv->sg_rx),
+				  sg_dma_address(&priv->sg_rx));
+
+	return;
+}
+
+static bool filter(struct dma_chan *chan, void *slave)
+{
+	struct pch_dma_slave *param = slave;
+
+	if ((chan->chan_id == param->chan_id) && (param->dma_dev ==
+						  chan->device->dev)) {
+		chan->private = param;
+		return true;
+	} else {
+		return false;
+	}
+}
+
+static void pch_request_dma(struct uart_port *port)
+{
+	dma_cap_mask_t mask;
+	struct dma_chan *chan;
+	struct pci_dev *dma_dev;
+	struct pch_dma_slave *param;
+	struct eg20t_port *priv =
+				container_of(port, struct eg20t_port, port);
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+
+	dma_dev = pci_get_bus_and_slot(2, PCI_DEVFN(0xa, 0)); /* Get DMA's dev
+								information */
+	/* Set Tx DMA */
+	param = &priv->param_tx;
+	param->dma_dev = &dma_dev->dev;
+	param->chan_id = priv->port.line;
+	param->tx_reg = port->mapbase + UART_TX;
+	chan = dma_request_channel(mask, filter, param);
+	if (!chan) {
+		pr_err("%s:dma_request_channel FAILS(Tx)\n", __func__);
+		return;
+	}
+	priv->chan_tx = chan;
+
+	/* Set Rx DMA */
+	param = &priv->param_rx;
+	param->dma_dev = &dma_dev->dev;
+	param->chan_id = priv->port.line + 1; /* Rx = Tx + 1 */
+	param->rx_reg = port->mapbase + UART_RX;
+	chan = dma_request_channel(mask, filter, param);
+	if (!chan) {
+		pr_err("%s:dma_request_channel FAILS(Rx)\n", __func__);
+		dma_release_channel(priv->chan_tx);
+		return;
+	}
+
+	/* Get Consistent memory for DMA */
+	priv->rx_buf_virt = dma_alloc_coherent(port->dev, port->fifosize,
+				    &priv->rx_buf_dma, GFP_KERNEL);
+	priv->chan_rx = chan;
+}
+
+static void pch_dma_rx_complete(void *arg)
+{
+	struct eg20t_port *priv = arg;
+	struct uart_port *port = &priv->port;
+	struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+
+	if (!tty) {
+		pr_debug("%s:tty is busy now", __func__);
+		return;
+	}
+
+	if (dma_push_rx(priv, priv->trigger_level))
+		tty_flip_buffer_push(tty);
+
+	tty_kref_put(tty);
+}
+
+static void pch_dma_tx_complete(void *arg)
+{
+	struct eg20t_port *priv = arg;
+	struct uart_port *port = &priv->port;
+	struct circ_buf *xmit = &port->state->xmit;
+
+	xmit->tail += sg_dma_len(&priv->sg_tx);
+	xmit->tail &= UART_XMIT_SIZE - 1;
+	port->icount.tx += sg_dma_len(&priv->sg_tx);
+
+	async_tx_ack(priv->desc_tx);
+	priv->tx_dma_use = 0;
+}
+
+static int pop_tx(struct eg20t_port *priv, unsigned char *buf, int size)
+{
+	int count = 0;
+	struct uart_port *port = &priv->port;
+	struct circ_buf *xmit = &port->state->xmit;
+
+	if (uart_tx_stopped(port) || uart_circ_empty(xmit) || count >= size)
+		goto pop_tx_end;
+
+	do {
+		int cnt_to_end =
+		    CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
+		int sz = min(size - count, cnt_to_end);
+		memcpy(&buf[count], &xmit->buf[xmit->tail], sz);
+		xmit->tail = (xmit->tail + sz) & (UART_XMIT_SIZE - 1);
+		count += sz;
+	} while (!uart_circ_empty(xmit) && count < size);
+
+pop_tx_end:
+	pr_debug("%d characters. Remained %d characters. (%lu)\n",
+		 count, size - count, jiffies);
+
+	return count;
+}
+
+static int handle_rx_to(struct eg20t_port *priv)
+{
+	struct pch_uart_buffer *buf;
+	int rx_size;
+	int ret;
+	if (!priv->start_rx) {
+		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT);
+		return 0;
+	}
+	buf = &priv->rxbuf;
+	do {
+		rx_size = pch_uart_hal_read(priv, buf->buf, buf->size);
+		ret = push_rx(priv, buf->buf, rx_size);
+		if (ret)
+			return 0;
+	} while (rx_size == buf->size);
+
+	return PCH_UART_HANDLED_RX_INT;
+}
+
+static int handle_rx(struct eg20t_port *priv)
+{
+	return handle_rx_to(priv);
+}
+
+static int dma_handle_rx(struct eg20t_port *priv)
+{
+	struct uart_port *port = &priv->port;
+	struct dma_async_tx_descriptor *desc;
+	struct scatterlist *sg;
+
+	priv = container_of(port, struct eg20t_port, port);
+	sg = &priv->sg_rx;
+
+	sg_init_table(&priv->sg_rx, 1); /* Initialize SG table */
+
+	sg_dma_len(sg) = priv->fifo_size;
+
+	sg_set_page(&priv->sg_rx, virt_to_page(priv->rx_buf_virt),
+		     sg_dma_len(sg), (unsigned long)priv->rx_buf_virt &
+		     ~PAGE_MASK);
+
+	sg_dma_address(sg) = priv->rx_buf_dma;
+
+	desc = priv->chan_rx->device->device_prep_slave_sg(priv->chan_rx,
+			sg, 1, DMA_FROM_DEVICE,
+			DMA_PREP_INTERRUPT);
+	if (!desc)
+		return 0;
+
+	priv->desc_rx = desc;
+	desc->callback = pch_dma_rx_complete;
+	desc->callback_param = priv;
+	desc->tx_submit(desc);
+	dma_async_issue_pending(priv->chan_rx);
+
+	return PCH_UART_HANDLED_RX_INT;
+}
+
+static unsigned int handle_tx(struct eg20t_port *priv)
+{
+	struct uart_port *port = &priv->port;
+	struct circ_buf *xmit = &port->state->xmit;
+	int ret;
+	int fifo_size;
+	int tx_size;
+	int size;
+	int tx_empty;
+
+	if (!priv->start_tx) {
+		pr_info("%s:Tx isn't started. (%lu)\n", __func__, jiffies);
+		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+		priv->tx_empty = 1;
+		return 0;
+	}
+
+	fifo_size = max(priv->fifo_size, 1);
+	tx_empty = 1;
+	if (pop_tx_x(priv, xmit->buf)) {
+		pch_uart_hal_write(priv, xmit->buf, 1);
+		port->icount.tx++;
+		tx_empty = 0;
+		fifo_size--;
+	}
+	size = min(xmit->head - xmit->tail, fifo_size);
+	tx_size = pop_tx(priv, xmit->buf, size);
+	if (tx_size > 0) {
+		ret = pch_uart_hal_write(priv, xmit->buf, tx_size);
+		port->icount.tx += ret;
+		tx_empty = 0;
+	}
+
+	priv->tx_empty = tx_empty;
+
+	if (tx_empty)
+		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+
+	return PCH_UART_HANDLED_TX_INT;
+}
+
+static unsigned int dma_handle_tx(struct eg20t_port *priv)
+{
+	struct uart_port *port = &priv->port;
+	struct circ_buf *xmit = &port->state->xmit;
+	struct scatterlist *sg = &priv->sg_tx;
+	int nent;
+	int fifo_size;
+	int tx_empty;
+	struct dma_async_tx_descriptor *desc;
+
+	if (!priv->start_tx) {
+		pr_info("%s:Tx isn't started. (%lu)\n", __func__, jiffies);
+		pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+		priv->tx_empty = 1;
+		return 0;
+	}
+
+	fifo_size = max(priv->fifo_size, 1);
+	tx_empty = 1;
+	if (pop_tx_x(priv, xmit->buf)) {
+		pch_uart_hal_write(priv, xmit->buf, 1);
+		port->icount.tx++;
+		tx_empty = 0;
+		fifo_size--;
+	}
+
+	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_TX_INT);
+
+	priv->tx_dma_use = 1;
+
+	sg_init_table(&priv->sg_tx, 1); /* Initialize SG table */
+
+	sg_set_page(&priv->sg_tx, virt_to_page(xmit->buf),
+		    UART_XMIT_SIZE, (int)xmit->buf & ~PAGE_MASK);
+
+	nent = dma_map_sg(port->dev, &priv->sg_tx, 1, DMA_TO_DEVICE);
+	if (!nent) {
+		pr_err("%s:dma_map_sg Failed\n", __func__);
+		return 0;
+	}
+
+	sg->offset = xmit->tail & (UART_XMIT_SIZE - 1);
+	sg_dma_address(sg) = (sg_dma_address(sg) & ~(UART_XMIT_SIZE - 1)) +
+			      sg->offset;
+	sg_dma_len(sg) = min((int)CIRC_CNT(xmit->head, xmit->tail,
+			     UART_XMIT_SIZE), CIRC_CNT_TO_END(xmit->head,
+			     xmit->tail, UART_XMIT_SIZE));
+
+	desc = priv->chan_tx->device->device_prep_slave_sg(priv->chan_tx,
+		sg, nent, DMA_TO_DEVICE, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	if (!desc) {
+		pr_err("%s:device_prep_slave_sg Failed\n", __func__);
+		return 0;
+	}
+
+	dma_sync_sg_for_device(port->dev, sg, 1, DMA_TO_DEVICE);
+
+	priv->desc_tx = desc;
+	desc->callback = pch_dma_tx_complete;
+	desc->callback_param = priv;
+
+	desc->tx_submit(desc);
+
+	dma_async_issue_pending(priv->chan_tx);
+
+	return PCH_UART_HANDLED_TX_INT;
+}
+
+static void pch_uart_err_ir(struct eg20t_port *priv, unsigned int lsr)
+{
+	u8 fcr = ioread8(priv->membase + UART_FCR);
+
+	/* Reset FIFO */
+	fcr |= UART_FCR_CLEAR_RCVR;
+	iowrite8(fcr, priv->membase + UART_FCR);
+
+	if (lsr & PCH_UART_LSR_ERR)
+		dev_err(&priv->pdev->dev, "Error data in FIFO\n");
+
+	if (lsr & UART_LSR_FE)
+		dev_err(&priv->pdev->dev, "Framing Error\n");
+
+	if (lsr & UART_LSR_PE)
+		dev_err(&priv->pdev->dev, "Parity Error\n");
+
+	if (lsr & UART_LSR_OE)
+		dev_err(&priv->pdev->dev, "Overrun Error\n");
+}
+
+static irqreturn_t pch_uart_interrupt(int irq, void *dev_id)
+{
+	struct eg20t_port *priv = dev_id;
+	unsigned int handled;
+	u8 lsr;
+	int ret = 0;
+	unsigned int iid;
+	unsigned long flags;
+
+	spin_lock_irqsave(&priv->port.lock, flags);
+	handled = 0;
+	while ((iid = pch_uart_hal_get_iid(priv)) > 1) {
+		switch (iid) {
+		case PCH_UART_IID_RLS:	/* Receiver Line Status */
+			lsr = pch_uart_hal_get_line_status(priv);
+			if (lsr & (PCH_UART_LSR_ERR | UART_LSR_FE |
+						UART_LSR_PE | UART_LSR_OE)) {
+				pch_uart_err_ir(priv, lsr);
+				ret = PCH_UART_HANDLED_RX_ERR_INT;
+			}
+			break;
+		case PCH_UART_IID_RDR:	/* Received Data Ready */
+			if (priv->use_dma)
+				ret = dma_handle_rx(priv);
+			else
+				ret = handle_rx(priv);
+			break;
+		case PCH_UART_IID_RDR_TO:	/* Received Data Ready
+						   (FIFO Timeout) */
+			ret = handle_rx_to(priv);
+			break;
+		case PCH_UART_IID_THRE:	/* Transmitter Holding Register
+						   Empty */
+			if (priv->use_dma)
+				ret = dma_handle_tx(priv);
+			else
+				ret = handle_tx(priv);
+			break;
+		case PCH_UART_IID_MS:	/* Modem Status */
+			ret = PCH_UART_HANDLED_MS_INT;
+			break;
+		default:	/* Never junp to this label */
+			pr_err("%s:iid=%d (%lu)\n", __func__, iid, jiffies);
+			ret = -1;
+			break;
+		}
+		handled |= (unsigned int)ret;
+	}
+	if (handled == 0 && iid <= 1) {
+		if (priv->int_dis_flag)
+			priv->int_dis_flag = 0;
+	}
+
+	spin_unlock_irqrestore(&priv->port.lock, flags);
+	return IRQ_RETVAL(handled);
+}
+
+/* This function tests whether the transmitter fifo and shifter for the port
+						described by 'port' is empty. */
+static unsigned int pch_uart_tx_empty(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	int ret;
+	priv = container_of(port, struct eg20t_port, port);
+	if (priv->tx_empty)
+		ret = TIOCSER_TEMT;
+	else
+		ret = 0;
+
+	return ret;
+}
+
+/* Returns the current state of modem control inputs. */
+static unsigned int pch_uart_get_mctrl(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	u8 modem;
+	unsigned int ret = 0;
+
+	priv = container_of(port, struct eg20t_port, port);
+	modem = pch_uart_hal_get_modem(priv);
+
+	if (modem & UART_MSR_DCD)
+		ret |= TIOCM_CAR;
+
+	if (modem & UART_MSR_RI)
+		ret |= TIOCM_RNG;
+
+	if (modem & UART_MSR_DSR)
+		ret |= TIOCM_DSR;
+
+	if (modem & UART_MSR_CTS)
+		ret |= TIOCM_CTS;
+
+	return ret;
+}
+
+static void pch_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	u32 mcr = 0;
+	unsigned int dat;
+	struct eg20t_port *priv = container_of(port, struct eg20t_port, port);
+
+	if (mctrl & TIOCM_DTR)
+		mcr |= UART_MCR_DTR;
+	if (mctrl & TIOCM_RTS)
+		mcr |= UART_MCR_RTS;
+	if (mctrl & TIOCM_LOOP)
+		mcr |= UART_MCR_LOOP;
+
+	if (mctrl) {
+		dat = pch_uart_get_mctrl(port);
+		dat |= mcr;
+		iowrite8(dat, priv->membase + UART_MCR);
+	}
+}
+
+static void pch_uart_stop_tx(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	priv = container_of(port, struct eg20t_port, port);
+	priv->start_tx = 0;
+	priv->tx_dma_use = 0;
+}
+
+static void pch_uart_start_tx(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+
+	priv = container_of(port, struct eg20t_port, port);
+
+	if (priv->use_dma)
+		if (priv->tx_dma_use)
+			return;
+
+	priv->start_tx = 1;
+	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT);
+}
+
+static void pch_uart_stop_rx(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	priv = container_of(port, struct eg20t_port, port);
+	priv->start_rx = 0;
+	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_RX_INT);
+	priv->int_dis_flag = 1;
+}
+
+/* Enable the modem status interrupts. */
+static void pch_uart_enable_ms(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	priv = container_of(port, struct eg20t_port, port);
+	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_MS_INT);
+}
+
+/* Control the transmission of a break signal. */
+static void pch_uart_break_ctl(struct uart_port *port, int ctl)
+{
+	struct eg20t_port *priv;
+	unsigned long flags;
+
+	priv = container_of(port, struct eg20t_port, port);
+	spin_lock_irqsave(&port->lock, flags);
+	pch_uart_hal_set_break(priv, ctl);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/* Grab any interrupt resources and initialise any low level driver state. */
+static int pch_uart_startup(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	int ret;
+	int fifo_size;
+	int trigger_level;
+
+	priv = container_of(port, struct eg20t_port, port);
+	priv->tx_empty = 1;
+	port->uartclk = priv->base_baud;
+	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT);
+	ret = pch_uart_hal_set_line(priv, default_baud,
+			      PCH_UART_HAL_PARITY_NONE, PCH_UART_HAL_8BIT,
+			      PCH_UART_HAL_STB1);
+	if (ret)
+		return ret;
+
+	switch (priv->fifo_size) {
+	case 256:
+		fifo_size = PCH_UART_HAL_FIFO256;
+		break;
+	case 64:
+		fifo_size = PCH_UART_HAL_FIFO64;
+		break;
+	case 16:
+		fifo_size = PCH_UART_HAL_FIFO16;
+	case 1:
+	default:
+		fifo_size = PCH_UART_HAL_FIFO_DIS;
+		break;
+	}
+
+	switch (priv->trigger) {
+	case PCH_UART_HAL_TRIGGER1:
+		trigger_level = 1;
+		break;
+	case PCH_UART_HAL_TRIGGER_L:
+		trigger_level = priv->fifo_size / 4;
+		break;
+	case PCH_UART_HAL_TRIGGER_M:
+		trigger_level = priv->fifo_size / 2;
+		break;
+	case PCH_UART_HAL_TRIGGER_H:
+	default:
+		trigger_level = priv->fifo_size - (priv->fifo_size / 8);
+		break;
+	}
+
+	priv->trigger_level = trigger_level;
+	ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0,
+				    fifo_size, priv->trigger);
+	if (ret < 0)
+		return ret;
+
+	ret = request_irq(priv->port.irq, pch_uart_interrupt, IRQF_SHARED,
+			KBUILD_MODNAME, priv);
+	if (ret < 0)
+		return ret;
+
+	if (priv->use_dma)
+		pch_request_dma(port);
+
+	priv->start_rx = 1;
+	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_RX_INT);
+	uart_update_timeout(port, CS8, default_baud);
+
+	return 0;
+}
+
+static void pch_uart_shutdown(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	int ret;
+
+	priv = container_of(port, struct eg20t_port, port);
+	pch_uart_hal_disable_interrupt(priv, PCH_UART_HAL_ALL_INT);
+	pch_uart_hal_fifo_reset(priv, PCH_UART_HAL_CLR_ALL_FIFO);
+	ret = pch_uart_hal_set_fifo(priv, PCH_UART_HAL_DMA_MODE0,
+			      PCH_UART_HAL_FIFO_DIS, PCH_UART_HAL_TRIGGER1);
+	if (ret)
+		pr_err("pch_uart_hal_set_fifo Failed(ret=%d)\n", ret);
+
+	if (priv->use_dma_flag)
+		pch_free_dma(port);
+
+	free_irq(priv->port.irq, priv);
+}
+
+/* Change the port parameters, including word length, parity, stop
+ *bits.  Update read_status_mask and ignore_status_mask to indicate
+ *the types of events we are interested in receiving.  */
+static void pch_uart_set_termios(struct uart_port *port,
+				 struct ktermios *termios, struct ktermios *old)
+{
+	int baud;
+	int rtn;
+	unsigned int parity, bits, stb;
+	struct eg20t_port *priv;
+	unsigned long flags;
+
+	priv = container_of(port, struct eg20t_port, port);
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		bits = PCH_UART_HAL_5BIT;
+		break;
+	case CS6:
+		bits = PCH_UART_HAL_6BIT;
+		break;
+	case CS7:
+		bits = PCH_UART_HAL_7BIT;
+		break;
+	default:		/* CS8 */
+		bits = PCH_UART_HAL_8BIT;
+		break;
+	}
+	if (termios->c_cflag & CSTOPB)
+		stb = PCH_UART_HAL_STB2;
+	else
+		stb = PCH_UART_HAL_STB1;
+
+	if (termios->c_cflag & PARENB) {
+		if (!(termios->c_cflag & PARODD))
+			parity = PCH_UART_HAL_PARITY_ODD;
+		else
+			parity = PCH_UART_HAL_PARITY_EVEN;
+
+	} else {
+		parity = PCH_UART_HAL_PARITY_NONE;
+	}
+	termios->c_cflag &= ~CMSPAR; /* Mark/Space parity is not supported */
+
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	uart_update_timeout(port, termios->c_cflag, baud);
+	rtn = pch_uart_hal_set_line(priv, baud, parity, bits, stb);
+	if (rtn)
+		goto out;
+
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+
+out:
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *pch_uart_type(struct uart_port *port)
+{
+	return KBUILD_MODNAME;
+}
+
+static void pch_uart_release_port(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+
+	priv = container_of(port, struct eg20t_port, port);
+	pci_iounmap(priv->pdev, priv->membase);
+	pci_release_regions(priv->pdev);
+}
+
+static int pch_uart_request_port(struct uart_port *port)
+{
+	struct eg20t_port *priv;
+	int ret;
+	void __iomem *membase;
+
+	priv = container_of(port, struct eg20t_port, port);
+	ret = pci_request_regions(priv->pdev, KBUILD_MODNAME);
+	if (ret < 0)
+		return -EBUSY;
+
+	membase = pci_iomap(priv->pdev, 1, 0);
+	if (!membase) {
+		pci_release_regions(priv->pdev);
+		return -EBUSY;
+	}
+	priv->membase = port->membase = membase;
+
+	return 0;
+}
+
+static void pch_uart_config_port(struct uart_port *port, int type)
+{
+	struct eg20t_port *priv;
+
+	priv = container_of(port, struct eg20t_port, port);
+	if (type & UART_CONFIG_TYPE) {
+		port->type = priv->port_type;
+		pch_uart_request_port(port);
+	}
+}
+
+static int pch_uart_verify_port(struct uart_port *port,
+				struct serial_struct *serinfo)
+{
+	struct eg20t_port *priv;
+
+	priv = container_of(port, struct eg20t_port, port);
+	if (serinfo->flags & UPF_LOW_LATENCY) {
+		pr_info("PCH UART : Use PIO Mode (without DMA)\n");
+		priv->use_dma = 0;
+		serinfo->flags &= ~UPF_LOW_LATENCY;
+	} else {
+#ifndef CONFIG_PCH_DMA
+		pr_err("%s : PCH DMA is not Loaded.\n", __func__);
+		return -EOPNOTSUPP;
+#endif
+		priv->use_dma = 1;
+		priv->use_dma_flag = 1;
+		pr_info("PCH UART : Use DMA Mode\n");
+	}
+
+	return 0;
+}
+
+static struct uart_ops pch_uart_ops = {
+	.tx_empty = pch_uart_tx_empty,
+	.set_mctrl = pch_uart_set_mctrl,
+	.get_mctrl = pch_uart_get_mctrl,
+	.stop_tx = pch_uart_stop_tx,
+	.start_tx = pch_uart_start_tx,
+	.stop_rx = pch_uart_stop_rx,
+	.enable_ms = pch_uart_enable_ms,
+	.break_ctl = pch_uart_break_ctl,
+	.startup = pch_uart_startup,
+	.shutdown = pch_uart_shutdown,
+	.set_termios = pch_uart_set_termios,
+/*	.pm		= pch_uart_pm,		Not supported yet */
+/*	.set_wake	= pch_uart_set_wake,	Not supported yet */
+	.type = pch_uart_type,
+	.release_port = pch_uart_release_port,
+	.request_port = pch_uart_request_port,
+	.config_port = pch_uart_config_port,
+	.verify_port = pch_uart_verify_port
+};
+
+static struct uart_driver pch_uart_driver = {
+	.owner = THIS_MODULE,
+	.driver_name = KBUILD_MODNAME,
+	.dev_name = PCH_UART_DRIVER_DEVICE,
+	.major = 0,
+	.minor = 0,
+	.nr = PCH_UART_NR,
+};
+
+static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
+						int port_type)
+{
+	struct eg20t_port *priv;
+	int ret;
+	unsigned int iobase;
+	unsigned int mapbase;
+	unsigned char *rxbuf;
+	int fifosize, base_baud;
+	static int num;
+
+	priv = kzalloc(sizeof(struct eg20t_port), GFP_KERNEL);
+	if (priv == NULL)
+		goto init_port_alloc_err;
+
+	rxbuf = (unsigned char *)__get_free_page(GFP_KERNEL);
+	if (!rxbuf)
+		goto init_port_free_txbuf;
+
+	switch (port_type) {
+	case PORT_UNKNOWN:
+		fifosize = 256; /* UART0 */
+		base_baud = 1843200; /* 1.8432MHz */
+		break;
+	case PORT_8250:
+		fifosize = 64; /* UART1~3 */
+		base_baud = 1843200; /* 1.8432MHz */
+		break;
+	default:
+		dev_err(&pdev->dev, "Invalid Port Type(=%d)\n", port_type);
+		goto init_port_hal_free;
+	}
+
+	iobase = pci_resource_start(pdev, 0);
+	mapbase = pci_resource_start(pdev, 1);
+	priv->mapbase = mapbase;
+	priv->iobase = iobase;
+	priv->pdev = pdev;
+	priv->tx_empty = 1;
+	priv->rxbuf.buf = rxbuf;
+	priv->rxbuf.size = PAGE_SIZE;
+
+	priv->fifo_size = fifosize;
+	priv->base_baud = base_baud;
+	priv->port_type = PORT_MAX_8250 + port_type + 1;
+	priv->port.dev = &pdev->dev;
+	priv->port.iobase = iobase;
+	priv->port.membase = NULL;
+	priv->port.mapbase = mapbase;
+	priv->port.irq = pdev->irq;
+	priv->port.iotype = UPIO_PORT;
+	priv->port.ops = &pch_uart_ops;
+	priv->port.flags = UPF_BOOT_AUTOCONF;
+	priv->port.fifosize = fifosize;
+	priv->port.line = num++;
+	priv->trigger = PCH_UART_HAL_TRIGGER_M;
+
+	pci_set_drvdata(pdev, priv);
+	pch_uart_hal_request(pdev, fifosize, base_baud);
+	ret = uart_add_one_port(&pch_uart_driver, &priv->port);
+	if (ret < 0)
+		goto init_port_hal_free;
+
+	return priv;
+
+init_port_hal_free:
+	free_page((unsigned long)rxbuf);
+init_port_free_txbuf:
+	kfree(priv);
+init_port_alloc_err:
+
+	return NULL;
+}
+
+static void pch_uart_exit_port(struct eg20t_port *priv)
+{
+	uart_remove_one_port(&pch_uart_driver, &priv->port);
+	pci_set_drvdata(priv->pdev, NULL);
+	free_page((unsigned long)priv->rxbuf.buf);
+}
+
+static void pch_uart_pci_remove(struct pci_dev *pdev)
+{
+	struct eg20t_port *priv;
+
+	priv = (struct eg20t_port *)pci_get_drvdata(pdev);
+	pch_uart_exit_port(priv);
+	pci_disable_device(pdev);
+	kfree(priv);
+	return;
+}
+#ifdef CONFIG_PM
+static int pch_uart_pci_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct eg20t_port *priv = pci_get_drvdata(pdev);
+
+	uart_suspend_port(&pch_uart_driver, &priv->port);
+
+	pci_save_state(pdev);
+	pci_set_power_state(pdev, pci_choose_state(pdev, state));
+	return 0;
+}
+
+static int pch_uart_pci_resume(struct pci_dev *pdev)
+{
+	struct eg20t_port *priv = pci_get_drvdata(pdev);
+	int ret;
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_restore_state(pdev);
+
+	ret = pci_enable_device(pdev);
+	if (ret) {
+		dev_err(&pdev->dev,
+		"%s-pci_enable_device failed(ret=%d) ", __func__, ret);
+		return ret;
+	}
+
+	uart_resume_port(&pch_uart_driver, &priv->port);
+
+	return 0;
+}
+#else
+#define pch_uart_pci_suspend NULL
+#define pch_uart_pci_resume NULL
+#endif
+
+static DEFINE_PCI_DEVICE_TABLE(pch_uart_pci_id) = {
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8811),
+	 .driver_data = PCH_UART_8LINE},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8812),
+	 .driver_data = PCH_UART_2LINE},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8813),
+	 .driver_data = PCH_UART_2LINE},
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x8814),
+	 .driver_data = PCH_UART_2LINE},
+	{0,},
+};
+
+static int __devinit pch_uart_pci_probe(struct pci_dev *pdev,
+					const struct pci_device_id *id)
+{
+	int ret;
+	struct eg20t_port *priv;
+
+	ret = pci_enable_device(pdev);
+	if (ret < 0)
+		goto probe_error;
+
+	priv = pch_uart_init_port(pdev, id->driver_data);
+	if (!priv) {
+		ret = -EBUSY;
+		goto probe_disable_device;
+	}
+	pci_set_drvdata(pdev, priv);
+
+	return ret;
+
+probe_disable_device:
+	pci_disable_device(pdev);
+probe_error:
+	return ret;
+}
+
+static struct pci_driver pch_uart_pci_driver = {
+	.name = "pch_uart",
+	.id_table = pch_uart_pci_id,
+	.probe = pch_uart_pci_probe,
+	.remove = __devexit_p(pch_uart_pci_remove),
+	.suspend = pch_uart_pci_suspend,
+	.resume = pch_uart_pci_resume,
+};
+
+static int __init pch_uart_module_init(void)
+{
+	int ret;
+
+	/* register as UART driver */
+	ret = uart_register_driver(&pch_uart_driver);
+	if (ret < 0)
+		return ret;
+
+	/* register as PCI driver */
+	ret = pci_register_driver(&pch_uart_pci_driver);
+	if (ret < 0)
+		uart_unregister_driver(&pch_uart_driver);
+
+	return ret;
+}
+module_init(pch_uart_module_init);
+
+static void __exit pch_uart_module_exit(void)
+{
+	pci_unregister_driver(&pch_uart_pci_driver);
+	uart_unregister_driver(&pch_uart_driver);
+}
+module_exit(pch_uart_module_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Intel EG20T PCH UART PCI Driver");
+module_param(default_baud, uint, S_IRUGO);
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index 9ffa5bee44ab..460a72d91bb7 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -1985,7 +1985,8 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 
 	tty_dev = device_find_child(uport->dev, &match, serial_match_port);
 	if (device_may_wakeup(tty_dev)) {
-		enable_irq_wake(uport->irq);
+		if (!enable_irq_wake(uport->irq))
+			uport->irq_wake = 1;
 		put_device(tty_dev);
 		mutex_unlock(&port->mutex);
 		return 0;
@@ -2051,7 +2052,10 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 
 	tty_dev = device_find_child(uport->dev, &match, serial_match_port);
 	if (!uport->suspended && device_may_wakeup(tty_dev)) {
-		disable_irq_wake(uport->irq);
+		if (uport->irq_wake) {
+			disable_irq_wake(uport->irq);
+			uport->irq_wake = 0;
+		}
 		mutex_unlock(&port->mutex);
 		return 0;
 	}
@@ -2134,6 +2138,7 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port)
 	case UPIO_AU:
 	case UPIO_TSI:
 	case UPIO_DWAPB:
+	case UPIO_DWAPB32:
 		snprintf(address, sizeof(address),
 			 "MMIO 0x%llx", (unsigned long long)port->mapbase);
 		break;
@@ -2554,6 +2559,7 @@ int uart_match_port(struct uart_port *port1, struct uart_port *port2)
 	case UPIO_AU:
 	case UPIO_TSI:
 	case UPIO_DWAPB:
+	case UPIO_DWAPB32:
 		return (port1->mapbase == port2->mapbase);
 	}
 	return 0;
diff --git a/drivers/serial/vt8500_serial.c b/drivers/serial/vt8500_serial.c
new file mode 100644
index 000000000000..322bf56c0d89
--- /dev/null
+++ b/drivers/serial/vt8500_serial.c
@@ -0,0 +1,648 @@
+/*
+ * drivers/serial/vt8500_serial.c
+ *
+ * Copyright (C) 2010 Alexey Charkov <alchark@gmail.com>
+ *
+ * Based on msm_serial.c, which is:
+ * Copyright (C) 2007 Google, Inc.
+ * Author: Robert Love <rlove@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#if defined(CONFIG_SERIAL_VT8500_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+# define SUPPORT_SYSRQ
+#endif
+
+#include <linux/hrtimer.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/slab.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+
+/*
+ * UART Register offsets
+ */
+
+#define VT8500_URTDR		0x0000	/* Transmit data */
+#define VT8500_URRDR		0x0004	/* Receive data */
+#define VT8500_URDIV		0x0008	/* Clock/Baud rate divisor */
+#define VT8500_URLCR		0x000C	/* Line control */
+#define VT8500_URICR		0x0010	/* IrDA control */
+#define VT8500_URIER		0x0014	/* Interrupt enable */
+#define VT8500_URISR		0x0018	/* Interrupt status */
+#define VT8500_URUSR		0x001c	/* UART status */
+#define VT8500_URFCR		0x0020	/* FIFO control */
+#define VT8500_URFIDX		0x0024	/* FIFO index */
+#define VT8500_URBKR		0x0028	/* Break signal count */
+#define VT8500_URTOD		0x002c	/* Time out divisor */
+#define VT8500_TXFIFO		0x1000	/* Transmit FIFO (16x8) */
+#define VT8500_RXFIFO		0x1020	/* Receive FIFO (16x10) */
+
+/*
+ * Interrupt enable and status bits
+ */
+
+#define TXDE	(1 << 0)	/* Tx Data empty */
+#define RXDF	(1 << 1)	/* Rx Data full */
+#define TXFAE	(1 << 2)	/* Tx FIFO almost empty */
+#define TXFE	(1 << 3)	/* Tx FIFO empty */
+#define RXFAF	(1 << 4)	/* Rx FIFO almost full */
+#define RXFF	(1 << 5)	/* Rx FIFO full */
+#define TXUDR	(1 << 6)	/* Tx underrun */
+#define RXOVER	(1 << 7)	/* Rx overrun */
+#define PER	(1 << 8)	/* Parity error */
+#define FER	(1 << 9)	/* Frame error */
+#define TCTS	(1 << 10)	/* Toggle of CTS */
+#define RXTOUT	(1 << 11)	/* Rx timeout */
+#define BKDONE	(1 << 12)	/* Break signal done */
+#define ERR	(1 << 13)	/* AHB error response */
+
+#define RX_FIFO_INTS	(RXFAF | RXFF | RXOVER | PER | FER | RXTOUT)
+#define TX_FIFO_INTS	(TXFAE | TXFE | TXUDR)
+
+struct vt8500_port {
+	struct uart_port	uart;
+	char			name[16];
+	struct clk		*clk;
+	unsigned int		ier;
+};
+
+static inline void vt8500_write(struct uart_port *port, unsigned int val,
+			     unsigned int off)
+{
+	writel(val, port->membase + off);
+}
+
+static inline unsigned int vt8500_read(struct uart_port *port, unsigned int off)
+{
+	return readl(port->membase + off);
+}
+
+static void vt8500_stop_tx(struct uart_port *port)
+{
+	struct vt8500_port *vt8500_port = container_of(port,
+						       struct vt8500_port,
+						       uart);
+
+	vt8500_port->ier &= ~TX_FIFO_INTS;
+	vt8500_write(port, vt8500_port->ier, VT8500_URIER);
+}
+
+static void vt8500_stop_rx(struct uart_port *port)
+{
+	struct vt8500_port *vt8500_port = container_of(port,
+						       struct vt8500_port,
+						       uart);
+
+	vt8500_port->ier &= ~RX_FIFO_INTS;
+	vt8500_write(port, vt8500_port->ier, VT8500_URIER);
+}
+
+static void vt8500_enable_ms(struct uart_port *port)
+{
+	struct vt8500_port *vt8500_port = container_of(port,
+						       struct vt8500_port,
+						       uart);
+
+	vt8500_port->ier |= TCTS;
+	vt8500_write(port, vt8500_port->ier, VT8500_URIER);
+}
+
+static void handle_rx(struct uart_port *port)
+{
+	struct tty_struct *tty = tty_port_tty_get(&port->state->port);
+	if (!tty) {
+		/* Discard data: no tty available */
+		int count = (vt8500_read(port, VT8500_URFIDX) & 0x1f00) >> 8;
+		u16 ch;
+		while (count--)
+			ch = readw(port->membase + VT8500_RXFIFO);
+		return;
+	}
+
+	/*
+	 * Handle overrun
+	 */
+	if ((vt8500_read(port, VT8500_URISR) & RXOVER)) {
+		port->icount.overrun++;
+		tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+	}
+
+	/* and now the main RX loop */
+	while (vt8500_read(port, VT8500_URFIDX) & 0x1f00) {
+		unsigned int c;
+		char flag = TTY_NORMAL;
+
+		c = readw(port->membase + VT8500_RXFIFO) & 0x3ff;
+
+		/* Mask conditions we're ignorning. */
+		c &= ~port->read_status_mask;
+
+		if (c & FER) {
+			port->icount.frame++;
+			flag = TTY_FRAME;
+		} else if (c & PER) {
+			port->icount.parity++;
+			flag = TTY_PARITY;
+		}
+		port->icount.rx++;
+
+		if (!uart_handle_sysrq_char(port, c))
+			tty_insert_flip_char(tty, c, flag);
+	}
+
+	tty_flip_buffer_push(tty);
+	tty_kref_put(tty);
+}
+
+static void handle_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+
+	if (port->x_char) {
+		writeb(port->x_char, port->membase + VT8500_TXFIFO);
+		port->icount.tx++;
+		port->x_char = 0;
+	}
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+		vt8500_stop_tx(port);
+		return;
+	}
+
+	while ((vt8500_read(port, VT8500_URFIDX) & 0x1f) < 16) {
+		if (uart_circ_empty(xmit))
+			break;
+
+		writeb(xmit->buf[xmit->tail], port->membase + VT8500_TXFIFO);
+
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		vt8500_stop_tx(port);
+}
+
+static void vt8500_start_tx(struct uart_port *port)
+{
+	struct vt8500_port *vt8500_port = container_of(port,
+						       struct vt8500_port,
+						       uart);
+
+	vt8500_port->ier &= ~TX_FIFO_INTS;
+	vt8500_write(port, vt8500_port->ier, VT8500_URIER);
+	handle_tx(port);
+	vt8500_port->ier |= TX_FIFO_INTS;
+	vt8500_write(port, vt8500_port->ier, VT8500_URIER);
+}
+
+static void handle_delta_cts(struct uart_port *port)
+{
+	port->icount.cts++;
+	wake_up_interruptible(&port->state->port.delta_msr_wait);
+}
+
+static irqreturn_t vt8500_irq(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	unsigned long isr;
+
+	spin_lock(&port->lock);
+	isr = vt8500_read(port, VT8500_URISR);
+
+	/* Acknowledge active status bits */
+	vt8500_write(port, isr, VT8500_URISR);
+
+	if (isr & RX_FIFO_INTS)
+		handle_rx(port);
+	if (isr & TX_FIFO_INTS)
+		handle_tx(port);
+	if (isr & TCTS)
+		handle_delta_cts(port);
+
+	spin_unlock(&port->lock);
+
+	return IRQ_HANDLED;
+}
+
+static unsigned int vt8500_tx_empty(struct uart_port *port)
+{
+	return (vt8500_read(port, VT8500_URFIDX) & 0x1f) < 16 ?
+						TIOCSER_TEMT : 0;
+}
+
+static unsigned int vt8500_get_mctrl(struct uart_port *port)
+{
+	unsigned int usr;
+
+	usr = vt8500_read(port, VT8500_URUSR);
+	if (usr & (1 << 4))
+		return TIOCM_CTS;
+	else
+		return 0;
+}
+
+static void vt8500_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static void vt8500_break_ctl(struct uart_port *port, int break_ctl)
+{
+	if (break_ctl)
+		vt8500_write(port, vt8500_read(port, VT8500_URLCR) | (1 << 9),
+			     VT8500_URLCR);
+}
+
+static int vt8500_set_baud_rate(struct uart_port *port, unsigned int baud)
+{
+	unsigned long div;
+	unsigned int loops = 1000;
+
+	div = vt8500_read(port, VT8500_URDIV) & ~(0x3ff);
+
+	if (unlikely((baud < 900) || (baud > 921600)))
+		div |= 7;
+	else
+		div |= (921600 / baud) - 1;
+
+	while ((vt8500_read(port, VT8500_URUSR) & (1 << 5)) && --loops)
+		cpu_relax();
+	vt8500_write(port, div, VT8500_URDIV);
+
+	return baud;
+}
+
+static int vt8500_startup(struct uart_port *port)
+{
+	struct vt8500_port *vt8500_port =
+			container_of(port, struct vt8500_port, uart);
+	int ret;
+
+	snprintf(vt8500_port->name, sizeof(vt8500_port->name),
+		 "vt8500_serial%d", port->line);
+
+	ret = request_irq(port->irq, vt8500_irq, IRQF_TRIGGER_HIGH,
+			  vt8500_port->name, port);
+	if (unlikely(ret))
+		return ret;
+
+	vt8500_write(port, 0x03, VT8500_URLCR);	/* enable TX & RX */
+
+	return 0;
+}
+
+static void vt8500_shutdown(struct uart_port *port)
+{
+	struct vt8500_port *vt8500_port =
+			container_of(port, struct vt8500_port, uart);
+
+	vt8500_port->ier = 0;
+
+	/* disable interrupts and FIFOs */
+	vt8500_write(&vt8500_port->uart, 0, VT8500_URIER);
+	vt8500_write(&vt8500_port->uart, 0x880, VT8500_URFCR);
+	free_irq(port->irq, port);
+}
+
+static void vt8500_set_termios(struct uart_port *port,
+			       struct ktermios *termios,
+			       struct ktermios *old)
+{
+	struct vt8500_port *vt8500_port =
+			container_of(port, struct vt8500_port, uart);
+	unsigned long flags;
+	unsigned int baud, lcr;
+	unsigned int loops = 1000;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* calculate and set baud rate */
+	baud = uart_get_baud_rate(port, termios, old, 900, 921600);
+	baud = vt8500_set_baud_rate(port, baud);
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+
+	/* calculate parity */
+	lcr = vt8500_read(&vt8500_port->uart, VT8500_URLCR);
+	lcr &= ~((1 << 5) | (1 << 4));
+	if (termios->c_cflag & PARENB) {
+		lcr |= (1 << 4);
+		termios->c_cflag &= ~CMSPAR;
+		if (termios->c_cflag & PARODD)
+			lcr |= (1 << 5);
+	}
+
+	/* calculate bits per char */
+	lcr &= ~(1 << 2);
+	switch (termios->c_cflag & CSIZE) {
+	case CS7:
+		break;
+	case CS8:
+	default:
+		lcr |= (1 << 2);
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= CS8;
+		break;
+	}
+
+	/* calculate stop bits */
+	lcr &= ~(1 << 3);
+	if (termios->c_cflag & CSTOPB)
+		lcr |= (1 << 3);
+
+	/* set parity, bits per char, and stop bit */
+	vt8500_write(&vt8500_port->uart, lcr, VT8500_URLCR);
+
+	/* Configure status bits to ignore based on termio flags. */
+	port->read_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->read_status_mask = FER | PER;
+
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	/* Reset FIFOs */
+	vt8500_write(&vt8500_port->uart, 0x88c, VT8500_URFCR);
+	while ((vt8500_read(&vt8500_port->uart, VT8500_URFCR) & 0xc)
+							&& --loops)
+		cpu_relax();
+
+	/* Every possible FIFO-related interrupt */
+	vt8500_port->ier = RX_FIFO_INTS | TX_FIFO_INTS;
+
+	/*
+	 * CTS flow control
+	 */
+	if (UART_ENABLE_MS(&vt8500_port->uart, termios->c_cflag))
+		vt8500_port->ier |= TCTS;
+
+	vt8500_write(&vt8500_port->uart, 0x881, VT8500_URFCR);
+	vt8500_write(&vt8500_port->uart, vt8500_port->ier, VT8500_URIER);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *vt8500_type(struct uart_port *port)
+{
+	struct vt8500_port *vt8500_port =
+			container_of(port, struct vt8500_port, uart);
+	return vt8500_port->name;
+}
+
+static void vt8500_release_port(struct uart_port *port)
+{
+}
+
+static int vt8500_request_port(struct uart_port *port)
+{
+	return 0;
+}
+
+static void vt8500_config_port(struct uart_port *port, int flags)
+{
+	port->type = PORT_VT8500;
+}
+
+static int vt8500_verify_port(struct uart_port *port,
+			      struct serial_struct *ser)
+{
+	if (unlikely(ser->type != PORT_UNKNOWN && ser->type != PORT_VT8500))
+		return -EINVAL;
+	if (unlikely(port->irq != ser->irq))
+		return -EINVAL;
+	return 0;
+}
+
+static struct vt8500_port *vt8500_uart_ports[4];
+static struct uart_driver vt8500_uart_driver;
+
+#ifdef CONFIG_SERIAL_VT8500_CONSOLE
+
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+	unsigned int status, tmout = 10000;
+
+	/* Wait up to 10ms for the character(s) to be sent. */
+	do {
+		status = vt8500_read(port, VT8500_URFIDX);
+
+		if (--tmout == 0)
+			break;
+		udelay(1);
+	} while (status & 0x10);
+}
+
+static void vt8500_console_putchar(struct uart_port *port, int c)
+{
+	wait_for_xmitr(port);
+	writeb(c, port->membase + VT8500_TXFIFO);
+}
+
+static void vt8500_console_write(struct console *co, const char *s,
+			      unsigned int count)
+{
+	struct vt8500_port *vt8500_port = vt8500_uart_ports[co->index];
+	unsigned long ier;
+
+	BUG_ON(co->index < 0 || co->index >= vt8500_uart_driver.nr);
+
+	ier = vt8500_read(&vt8500_port->uart, VT8500_URIER);
+	vt8500_write(&vt8500_port->uart, VT8500_URIER, 0);
+
+	uart_console_write(&vt8500_port->uart, s, count,
+			   vt8500_console_putchar);
+
+	/*
+	 *	Finally, wait for transmitter to become empty
+	 *	and switch back to FIFO
+	 */
+	wait_for_xmitr(&vt8500_port->uart);
+	vt8500_write(&vt8500_port->uart, VT8500_URIER, ier);
+}
+
+static int __init vt8500_console_setup(struct console *co, char *options)
+{
+	struct vt8500_port *vt8500_port;
+	int baud = 9600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (unlikely(co->index >= vt8500_uart_driver.nr || co->index < 0))
+		return -ENXIO;
+
+	vt8500_port = vt8500_uart_ports[co->index];
+
+	if (!vt8500_port)
+		return -ENODEV;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(&vt8500_port->uart,
+				 co, baud, parity, bits, flow);
+}
+
+static struct console vt8500_console = {
+	.name = "ttyWMT",
+	.write = vt8500_console_write,
+	.device = uart_console_device,
+	.setup = vt8500_console_setup,
+	.flags = CON_PRINTBUFFER,
+	.index = -1,
+	.data = &vt8500_uart_driver,
+};
+
+#define VT8500_CONSOLE	(&vt8500_console)
+
+#else
+#define VT8500_CONSOLE	NULL
+#endif
+
+static struct uart_ops vt8500_uart_pops = {
+	.tx_empty	= vt8500_tx_empty,
+	.set_mctrl	= vt8500_set_mctrl,
+	.get_mctrl	= vt8500_get_mctrl,
+	.stop_tx	= vt8500_stop_tx,
+	.start_tx	= vt8500_start_tx,
+	.stop_rx	= vt8500_stop_rx,
+	.enable_ms	= vt8500_enable_ms,
+	.break_ctl	= vt8500_break_ctl,
+	.startup	= vt8500_startup,
+	.shutdown	= vt8500_shutdown,
+	.set_termios	= vt8500_set_termios,
+	.type		= vt8500_type,
+	.release_port	= vt8500_release_port,
+	.request_port	= vt8500_request_port,
+	.config_port	= vt8500_config_port,
+	.verify_port	= vt8500_verify_port,
+};
+
+static struct uart_driver vt8500_uart_driver = {
+	.owner		= THIS_MODULE,
+	.driver_name	= "vt8500_serial",
+	.dev_name	= "ttyWMT",
+	.nr		= 6,
+	.cons		= VT8500_CONSOLE,
+};
+
+static int __init vt8500_serial_probe(struct platform_device *pdev)
+{
+	struct vt8500_port *vt8500_port;
+	struct resource *mmres, *irqres;
+	int ret;
+
+	mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	irqres = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (!mmres || !irqres)
+		return -ENODEV;
+
+	vt8500_port = kzalloc(sizeof(struct vt8500_port), GFP_KERNEL);
+	if (!vt8500_port)
+		return -ENOMEM;
+
+	vt8500_port->uart.type = PORT_VT8500;
+	vt8500_port->uart.iotype = UPIO_MEM;
+	vt8500_port->uart.mapbase = mmres->start;
+	vt8500_port->uart.irq = irqres->start;
+	vt8500_port->uart.fifosize = 16;
+	vt8500_port->uart.ops = &vt8500_uart_pops;
+	vt8500_port->uart.line = pdev->id;
+	vt8500_port->uart.dev = &pdev->dev;
+	vt8500_port->uart.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
+	vt8500_port->uart.uartclk = 24000000;
+
+	snprintf(vt8500_port->name, sizeof(vt8500_port->name),
+		 "VT8500 UART%d", pdev->id);
+
+	vt8500_port->uart.membase = ioremap(mmres->start,
+					    mmres->end - mmres->start + 1);
+	if (!vt8500_port->uart.membase) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	vt8500_uart_ports[pdev->id] = vt8500_port;
+
+	uart_add_one_port(&vt8500_uart_driver, &vt8500_port->uart);
+
+	platform_set_drvdata(pdev, vt8500_port);
+
+	return 0;
+
+err:
+	kfree(vt8500_port);
+	return ret;
+}
+
+static int __devexit vt8500_serial_remove(struct platform_device *pdev)
+{
+	struct vt8500_port *vt8500_port = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+	uart_remove_one_port(&vt8500_uart_driver, &vt8500_port->uart);
+	kfree(vt8500_port);
+
+	return 0;
+}
+
+static struct platform_driver vt8500_platform_driver = {
+	.probe  = vt8500_serial_probe,
+	.remove = vt8500_serial_remove,
+	.driver = {
+		.name = "vt8500_serial",
+		.owner = THIS_MODULE,
+	},
+};
+
+static int __init vt8500_serial_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&vt8500_uart_driver);
+	if (unlikely(ret))
+		return ret;
+
+	ret = platform_driver_register(&vt8500_platform_driver);
+
+	if (unlikely(ret))
+		uart_unregister_driver(&vt8500_uart_driver);
+
+	return ret;
+}
+
+static void __exit vt8500_serial_exit(void)
+{
+#ifdef CONFIG_SERIAL_VT8500_CONSOLE
+	unregister_console(&vt8500_console);
+#endif
+	platform_driver_unregister(&vt8500_platform_driver);
+	uart_unregister_driver(&vt8500_uart_driver);
+}
+
+module_init(vt8500_serial_init);
+module_exit(vt8500_serial_exit);
+
+MODULE_AUTHOR("Alexey Charkov <alchark@gmail.com>");
+MODULE_DESCRIPTION("Driver for vt8500 serial device");
+MODULE_LICENSE("GPL");